REPAIR PARTS MANUAL. MODEL NO. M155107H ( ) Lawn Tractor Rev 2.

Size: px

Start display at page:

Download "REPAIR PARTS MANUAL. MODEL NO. M155107H ( ) Lawn Tractor Rev 2."

Blanche Fleming
5 years ago
Views:

1 REPAIR PARTS MANUAL MODEL NO. M155107H ( ) Lawn Tractor Rev 2 1

2 HOW TO USE THIS MANUAL This manual is designed to provide the customer with a means to identify the parts on his/her tractor when ordering repair parts. The illustrations may or may not represent the actual assemblies; therefore, it is not recommended to use this manual as a guide to assemble or disassemble the tractor. Some hardware and parts are drawn larger in order to more readily identify them. Each tractor has its own model number. The model number for your tractor can be found on the fender under the seat. When ordering parts, always give the following information: Product - Tractor Model Number - M155107H ( ) Part Number Part Description TABLE OF CONTENTS SCHEMATIC... 3 ELECTRICAL CHASSIS...-7 DRIVE STEERING ENGINE SEAT...14 DECALS MOWER DECK MOWER LIFT

3 SCHEMATIC SCH12 A AMMETER (OPTIONAL) RED FUSE BATTERY RED SOLENOID STARTER M WHITE PTO SWITCH (DISENGAGED) WHITE ELECTRIC CLUTCH S B M A1 G L A2 RED C A H D WHITE RED CLUTCH/BRAKE (PEDAL UP) GRAY B E REVERSE SWITCH (NOT IN REVERSE) SEAT SWITCH (NOT OCCUPIED) GRAY /WHITE JUNCTION CONNECTOR CHASSIS HARNESS SHORTING CONNECTOR C B A F E D H G BLUE IGNITION UNIT (OPTIONAL) HOUR METER SPARK PLUGS GAP (2 PLUGS ON TWIN CYL. ENGINES) PTO SWITCH (MATING SIDE) BLUE FUEL LINE BLUE 12V POWER OUTLET (OPTIONAL) NOTES ORANGE FUEL SHUT-OFF SOLENOID (IF EQUIPPED) RED CHARGING SYSTEM OUTPUT 9-1AMPDC@300 RPM REGULATOR STATOR 28 VOLTS 300 RPM (REGULATOR DISCONNECTED) BROWN LIGHT SWITCH HEADLIGHTS IGNITION SWITCH POSITION CIRCUIT MAKE OFF RUN/OVERRIDE RUN M+G+A1 B+A1 B+A1 L+A2 START B+S+A CHASSIS HARNESS CONNECTOR (MATING SIDE) 5 4 DASH HARNESS CONNECTOR WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING. NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS

4 ELECTRICAL T08S_r1 With 12V Outlet Option With Service Minder Option

5 ELECTRICAL Battery Bolt Hex Hd 1/4-20 unc x 3/ Battery Box Switch Interlock Harness Socket Light Bulb, Light # Cable Starter Fuse Nut Keps Hex 1/4-20 unc Cable Ground Switch Seat Switch Ign Key/Chain Switch Light/Reset Harness Ign. Dash Screw Thd Cut 1/4-20 x 1/ Cover Terminal Red Solenoid Switch PTO Screw Thdrol 5/1-18 x 3/ Harness Chassis Socket Asm. Bulb Cover Terminal Battery Harness Pigtail Console ROS Screw Plastite x Module Reverse ROS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 5

6 CHASSIS

7 CHASSIS Drawbar Dash Hood Lens LH Grille Lens RH Screw 5/1-18 x 3/ Fender Light Asm Dual Screw THDROL 5/1-18 x 1/2 TYTT Screw x 5/ Screw #10 x.750 BOS Thread Bolt Shoulder 5/ Bumper Extrusion Air Duct Shield Browning Screw 3/8-1 x 3/ Crossmember Screw x 5/ Bushing Steering Cargo Net Asm Chassis Bushing Mtg. Fender Crgo Dash Lower Bolt Fin Hex 5/1-18 unc x 1-1/ Bracket Pick-Off Hood Nut Lock Hex Flange 5/ Plug Hole Dash Lower Console Asm. Deck Lift Skirt Hood Side LH Skirt Hood Side RH Stud Fastner Bolt Shoulder 5/ Spacer Fender Nut Lock 5/1-18 unc Screw Hex 1/4-20 x 3/ Plug Dash Plug Cruise Control NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 7

8 DRIVE

9 DRIVE Transaxle, TUFFTORQ K4 BA Key Washer 13/32 x 13/1 x 1 Ga Spring, Brake Rod Shift Knob Rod, Brake Ring E Rod, Brake, Park Cover, Foot Pedal Bolt Pulley Idler Flat Lock Nut 3/ Idler V-Groove 910" Offset V-Belt, Drive Shaft Asm. Pedal Brake Control Console Bolt Hex Flghd 5/1-18 Gr Screw 1/4 x 1/ Strap Torque Rod Bypass Nut Lock Hex Flange 5/ Screw 5/1-18 x 3/ Retainer Spring Pin Cotter 1/8 x 3/ Retainer Clip Spring, Return, Clutch Nut Push Latch Brake Parking Keeper Belt Centerspan Bolt RDHD SQNK 3/8-1 unc x Nut Push Shaft Asm Shift Arm Clevis Rod Shift Spring Shift Spacer Split Handle Parking Brake Bolt Rdhd Sqnk 3/8-1 x 2-3/ Spacer Retainer Washer Link Clutch Ground Drive Bellcrank Ground Drive Keeper Bellcrank Ground Drive Screw 3/8-1 x Bracket Clutch Anti-Rotation Washer Bushing Brake Shaft Retainer Spring Clip Handle Keeper Belt Trans Bracket Mount Touque Washer Hardened Washer Serrated Screw 3/8-1 x 3/ Washer 13/32 x 1 x 14 Ga Guard Muffler Bolt 7/1-14 x 1 Gr Link Shift NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 9

10 STEERING ASSEMBLY steering-tex_legnd2_2_r1 10

11 STEERING ASSEMBLY Wheel, Steering Axle Asm., Front Spindle Asm., LH Spindle Asm., RH Washer.75 x Thrust Washer 25/32 x 1-5/8 x 1 Ga Ring, Clip #T Cap, Spindle Washer 25/32 x 1-1/4 x 1 Ga Washer, Lock Hvy Hlcl Spr 3/ Nut, Crown Lock 3/8-24 unf Shaft Steering Plate Steering Boot Steering Adapter, Wheel Steering Bushing, Strg. Blk Insert, Wheel Steering Screw 3/8-1 x 3/ Gear, Sector Plate Washer 11/32 x 2-3/8 x 12 Ga Nut Lock 3/8-1 unc Nut Hex Jam Toplock 1/2-20 unf Washer Hardened.793 x 1.37 x Bolt 3/8-1 unc x 2-1/ Spacer Brace Axle Bracket Upstop Bolt Shoulder Sector Pivot CFM Washer Thrust Sector Steering Nut Flange Lock 5/ Draglink, LH Draglink, RH Screw 5/1-18 x 3/ Retainer Clip Spring Steering Brace Axle Front Bolt Hex Fghd 7/1-14 x 3 Serr Bushing PM Front Axle Nut Lock Flange 7/1-14 Gr Washer 1.5 x.505 x Bracket Deck Susp. Front Bearing Washer Thrust.515 x.750 x.033 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 11

12 ENGINE 12

13 ENGINE Engine Briggs Model No. 31A Muffler Keeper Belt Engine Clutch Electric Pulley Engine Tank Fuel Cap Asm Control Throttle Screw #10 x.750 BOS Thread Control Choke Fuel Line Spark Arrester Kit Clamp Hose Washer 1-1/2 OD x 15/32 ID x Washer Lock 7/ Nut Keps Hex 1/4-20 unc Gasket Screw 5/1-18 x Tube Drain Oil Easy Plug Drain Oil Screw 3/8-1 x 1-1/ Bolt 7/1-20 x Screw 3/8-1 x Washer 9/32 x 7/8 x 1 Ga Screw 1/4-20 x 3/4 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm Engine Power Rating Information The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J11940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision ). Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual on-site or net horsepower). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine. 13

14 SEAT ASSEMBLY seat-tex_7a-vgt Seat Bracket Pivot Fender Strap, Asm Fender Nut, Lock w/ins. 3/8-1 unc Spring, Seat Cprsn Bolt 5/1-18 unc x 3/4 w/sems Pan, Seat Bolt, Shoulder 5/ Nut, Lock 5/1-18 unc Handle Slide Seat Spring Latch Seat Bolt 3/8-1 x 3/ Washer 13/32 x 2-3/8 x 12 Ga. NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 14

15 DECALS Decal, Warning Sym Decal, Warning Decal, Warning Engine Decal, V-Belt Sch Decal, Eng. HP Decal, Hood LH/RH Decal, Cutfinger Decal, Battery Dnge/Poi Decal, Fender Decal, Fender DB/CE Decal, Steering Whl Decal, Panel Side Decal, Hot Muffler Decal, Clutch/Brake Decal, Saddle Brake Parking Decal, Enviro Decal, Bypass Decal, Load Limit Pad, Footrest, LH Pad, Footrest, RH Manual, Oper Euro Manual, Oper Scan Manual, Oper E-Bloc Manual, Oper Baltic Manual, Parts WHEELS AND TIRES Cap, Valve, Tire Stem, Valve Rim Assembly, Front Tube, Front (Ser vice Item Only) Tire, Front Fitting, Grease (Front Wheel Only) Bearing, Flange (Front Wheel Only) Cap, Axle (Front Wheel Only) Tire, Rear Tube, Rear (Service Item Only) Rim Assembly, Rear Sealant, Tire (10 oz. Tube) wheel_art_1-vgt 15 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm

16 MOWER DECK _D_elec-Tex_10_r _mulch_plate_

17 MOWER DECK Mower Housing Arm Suspension Bolt/Washer Asm 7/1-20 unf Blade Shaft Assembly, Mandrel Housing, Mandrel Bearing, Ball, Mandrel Stripper, Mower Deck Bolt, Shoulder Baffle, Vortex Nut, Crownlock 5/1-18 unc Bracket, Deflector Cap, Sleeve Spring, Torsion, Deflector Nut, Push Shield, Deflector Rod, Hinge Screw Thdrol Rolling Wsh Hd Washer, Spacer Pulley, Mandrel Nut, Toplock, Flanged Bolt Carr Sh. 3/8-1 x 1-1/2 Gr Pulley Idler Nut, Lock Flg. 3/8-1 unc Arm, Idler Spacer, Retainer Screw 3/8-1 x Guard, Tuv Idler Bolt RDHD 3/8-1 unc x V-Belt Bolt Washer, Flat Hardened Cover Mulching Screw x 5/ Washer # Washer Lock # Latch Asm Nut Weld Bolt, Shoulder Wheel, Gauge Nut, Lock 3/8-1 unc Washer 3/8 x 7/8 x 14 Ga Pulley, Idler, Primary Stud Fastener Nut Lock Hex Flange Spring Mower Drive Electric Screw THDROL 3/8-1 x 1/ Mandrel Assembly (Includes housing, shaft and shaft hard ware only-pulley not included) Replacement Mower, Complete NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 17

18 MOWER LIFT * lift-tex_1_r3 *Key 91 may be substituted for Key Shaft Asm., Lift Lever Asm., Lift Grip, Lever Spring Torsion Pin Cotter 7/1 Bow Tie Lock Spring Lift Assist Washer Clear Zinc Pin Cotter 5/1 Bow Tie Lock Link Lift Susp Mower Rear Screw 3/8-1 x 3/ Link Lift Susp. Front Mower Nut Centerlock 3/ Link Asm. Lift FXD NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 18

19 SERVICE NOTES 19

20 TH PRINTED IN USA

KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION

KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 874 78 04-10 Bolt, Fin Hex 1/4-20 x 5/8 12 532 13 09-86 Lens, LH 3 532 12 84-45 Bracket, Pivot Hood LH 13 532 13 09-84 Grille 4 819 09 10-16 Washer, Flat 1/4 21 532 12 69-38 Bumper, Hood 5 817 49 05-12