CYCLIC PERFORMANCE PER ASTM E 330 TEST REPORT. Rendered to: TRUSEAL TECHNOLOGIES, LTD. PRODUCT TYPE: Fixed Window

Size: px

Start display at page:

Download "CYCLIC PERFORMANCE PER ASTM E 330 TEST REPORT. Rendered to: TRUSEAL TECHNOLOGIES, LTD. PRODUCT TYPE: Fixed Window"

Roderick Barber
5 years ago
Views:

1 CYCLIC PERFORMANCE PER ASTM E 330 TEST REPORT Rendered to: TRUSEAL TECHNOLOGIES, LTD. PRODUCT TYPE: Fixed Window Report No.: Test Dates: 07/30/07 Through: 08/03/07 Report Date: 08/20/07 Expiration Date: 08/03/ Derry Court York, PA phone: fax:

2 CYCLIC PERFORMANCE PER ASTM E 330 TEST REPORT Rendered to: TRUSEAL TECHNOLOGIES, LTD. 260 Jackson Street West Hamilton, Ontario L8P 1M5 CANADA Report No.: Test Dates: 07/30/07 Through: 08/03/07 Report Date: 08/20/07 Expiration Date: 08/03/11 Project Summary: Architectural Testing, Inc. was contracted by TruSeal Technologies, Ltd. to perform testing on five fixed windows. The samples tested met the performance requirements set forth in the referenced test procedures for a Pa (-80.0 psf). Test specimen description and results are reported herein. The samples were provided by the client. Test Procedures: The test specimens were evaluated in accordance with the client provided test plan as well as in general accordance with ASTM E , Test Method for Structural Performance of Exterior Windows, Curtain Walls and Doors by Uniform Static Air Pressure Difference. Test Specimen Description: Test Specimen #1: Spacer Type: Duraseal (Single Seal) Test Specimen #2: Spacer Type: Conventional Spacer System Test Specimen #3: Spacer Type: Duralite (Single Seal) Test Specimen #4: Spacer Type: Duraseal (Dual-Seal) Test Specimen #5: Spacer Type: Duralite (Dual-Seal) Product Type: Fixed Window The following descriptions apply to all specimens. Overall Size: 1524 mm (60") wide by 1829 mm (72") high Fixed Daylight Opening Size: 1448 mm (57") wide by 1753 mm (69") high 130 Derry Court York, PA phone: fax:

3 Page 2 of 10 Test Specimen Description: (Continued) Finish: All aluminum was painted. Glazing Details: The unit was glazed with 1" thick insulating glass constructed of two sheets of 1/4" thick clear tempered glass and a spacer system. The glass was set from the interior against hot melt glazing compound and secured with aluminum snap-in glazing bead with a four fin rubber compression gasket. Frame Construction: The frame was constructed of extruded aluminum. The corners were square-cut, sealed, and secured with #8 x 1-1/2" screws. Installation: The units were installed into a Spruce-Pine-Fir wood test buck. The nail fin was set against a bed of silicone and was secured with #6 x 1-1/4" screws through the nail fin into the buck, 3" from each corner and spaced 13" on center.

4 Page 3 of 10 Test Results: The temperature during testing was 27 C (80 F). The results are tabulated as follows: ASTM E 330, Air Pressure Cycling Test Unit #1: Duraseal (Single Seal) Design Pressure: Pa (-80.0 psf) Pressure Range Pa (psf) 0 to 3828 (0 to 80) 0 to 5742 (0 to 120) 3828 to 0 (80 to 0) 957 to 0 (20 to 0) Number of Cycles Average Cycle Time (Seconds) NEGATIVE PRESSURE Maximum Deflection at Indicator mm (inch) #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11 # N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A (3) 4.6 (0.18) 4.6 (0.18) 26.7 (5) 1 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A (4) 19.1 (0.75) 14.7 (0.58) 5.3 (0.21) 4.1 (0.16) 3.1 (0.12) 6.4 () 5.6 (0.22) 5.6 (0.22) 9.7 (0.38) 8.4 (0.33) 7.6 (0.30) 29.0 (1.14) 22.1 (0.87) 17.8 (0.70) 3.3 (0.13) Observations: No damage was observed. Result: Pass Note: See Architectural Testing, Inc. Sketch #1 for indicator locations.

5 Page 4 of 10 Test Results: (Continued) ASTM E 330, Air Pressure Cycling Test Unit #2: Conventional Spacer System Design Pressure: Pa (-80.0 psf) Pressure Range Pa (psf) 0 to 3828 (0 to 80) 0 to 5742 (0 to 120) 3828 to 0 (80 to 0) 957 to 0 (20 to 0) Number of Cycles Average Cycle Time (Seconds) NEGATIVE PRESSURE Maximum Deflection at Indicator mm (inch) #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11 # N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A (0.94) 5.1 (0.20) 6.1 (0.24) 3.8 (0.15) 26.2 (3) 1 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A (0.15) 4.1 (0.16) 2.8 (0.11) 24.9 (0.98) 18.5 (0.73) 6.6 (0.26) 4.8 (0.19) 3.8 (0.15) 6.9 (0.27) 4.6 (0.18) 4.6 (0.18) 27.2 (7) 19.8 (0.78) Observations: No damage was observed. Result: Pass Note: See Architectural Testing, Inc. Sketch #1 for indicator locations.

6 Page 5 of 10 Test Results: (Continued) ASTM E 330, Air Pressure Cycling Test Unit #3: Duralite (Single Seal) Design Pressure: Pa (-80.0 psf) Pressure Range Pa (psf) 0 to 3828 (0 to 80) 0 to 5742 (0 to 120) 3828 to 0 (80 to 0) 957 to 0 (20 to 0) Number of Cycles Average Cycle Time (Seconds) NEGATIVE PRESSURE Maximum Deflection at Indicator mm (inch) #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11 # N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A (7) 6.1 (0.24) 3.1 (0.12) 5.8 (0.23) 27.4 (8) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A < (<0.01) 27.4 (8) 20.3 (0.80) 14.7 (0.58) 5.6 (0.22) 3.8 (0.15) 5.1 (0.20) 3.3 (0.13) 25.9 (2) 19.1 (0.75) 14.7 (0.58) 2.8 (0.11) Observations: No damage was observed. Result: Pass Note: See Architectural Testing, Inc. Sketch #1 for indicator locations.

7 Page 6 of 10 Test Results: (Continued) ASTM E 330, Air Pressure Cycling Test Unit #4: Duraseal (Dual-Seal) Design Pressure: Pa (-80.0 psf) Pressure Range Pa (psf) 0 to 3828 (0 to 80) 0 to 5742 (0 to 120) 3828 to 0 (80 to 0) 957 to 0 (20 to 0) Number of Cycles Average Cycle Time (Seconds) NEGATIVE PRESSURE Maximum Deflection at Indicator mm (inch) #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11 # N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A (0.99) 5.1 (0.20) 3.6 (0.14) 5.3 (0.21) 25.6 (1) 1 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A (0) 18.8 (0.74) 18.8 (0.74) 6.1 (0.24) 4.6 (0.18) 4.6 (0.18) 5.8 (0.23) 4.1 (0.16) 4.1 (0.16) 25.2 (0.99) 18.5 (0.73) 18.5 (0.73) Observations: No damage was observed. Result: Pass Note: See Architectural Testing, Inc. Sketch #1 for indicator locations.

8 Page 7 of 10 Test Results: (Continued) ASTM E 330, Air Pressure Cycling Test Unit #5: Duralite (Dual-Seal) Design Pressure: Pa (-80.0 psf) Pressure Range Pa (psf) 0 to 3828 (0 to 80) 0 to 5742 (0 to 120) 3828 to 0 (80 to 0) 957 to 0 (20 to 0) Number of Cycles Average Cycle Time (Seconds) NEGATIVE PRESSURE Maximum Deflection at Indicator mm (inch) #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11 #12 1 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A (1) 5.1 (0.20) 5.3 (0.21) 25.4 (0) 1 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A (4) 19.8 (0.78) 14.7 (0.58) 5.6 (0.22) 4.1 (0.16) 2.8 (0.11) 6.1 (0.24) 4.1 (0.16) 2.8 (0.11) 26.7 (5) 19.6 (0.77) 15.0 (0.59) Observations: No damage was observed. Result: Pass Note: See Architectural Testing, Inc. Sketch #1 for indicator locations. Conclusion: Five insulating glass spacer systems were tested for cyclic wind pressure performance in accordance to the client provided test plan. During the testing and at the conclusion of the testing, all five spacer systems performed in a similar manner. It is our opinion that there is no difference in performance of the five insulating glass spacer systems tested.

9 Page 8 of 10 Test Equipment: Cycling Mechanism: Computer controlled centrifugal blower with electronic pressure measuring device Deflection Measuring Device: Linear transducers Tape and film were not used to seal against air leakage during structural testing. Drawing Reference: The test specimen drawings have been reviewed by Architectural Testing, Inc. and are representative of the test specimen reported herein. List of Official Observers: Name Werner Lichtenberger, P.E. Stephen D. Shank Tim McGill Michael D. Stremmel, P.E. Jeremy R. Bender Company TruSeal Technologies, Ltd. Architectural Testing, Inc. Architectural Testing, Inc. Architectural Testing, Inc. Architectural Testing, Inc.

Page 9 of 10 Detailed drawings, data sheets, representative samples of test specimens, a copy of this report, or other pertinent project documentation will be retained by Architectural Testing, Inc.

Results obtained are tested values and were secured by using the designated test methods.

10 Page 9 of 10 Detailed drawings, data sheets, representative samples of test specimens, a copy of this report, or other pertinent project documentation will be retained by Architectural Testing, Inc. for a period of four years from the original test date. At the end of this retention period, such materials shall be discarded without notice and the service life of this report will expire. Results obtained are tested values and were secured by using the designated test methods. This report does not constitute certification of this product nor an opinion or endorsement by this laboratory. It is the exclusive property of the client so named herein and relates only to the specimen(s) tested. This report may not be reproduced, except in full, without the written approval of Architectural Testing, Inc. For ARCHITECTURAL TESTING, INC. Jeremy R. Bender Technician Michael D. Stremmel, P.E. Senior Project Engineer JRB:vlm Attachments (pages): This report is complete only when all attachments listed are included. Appendix-A: Sketch (1)

11 Page 10 of 10 Revision Log Rev. # Date Page(s) Revision(s) 0 08/20/07 N/A Original report issue 1 09/27/07 Page 1, 3, 5, 6, 7 Page 8 Changed Dura-Seal and Dura-Lite to Duraseal and Duralite Added P.E. to Werner Lichtenberger This report produced from controlled document template ATI 00165, revised 07/23/07.

12 Appendix A Sketch

ASTM E1886 and ASTM E1996 TEST REPORT. Report No.: E Rendered to: 3M COMPANY St. Paul, Minnesota 55144

ASTM E1886 and ASTM E1996 TEST REPORT Report No.: E6587.01 201 44 Rendered to: 3M COMPANY St. Paul, Minnesota 55144 PRODUCT TYPE: Safety and Security Window Film SERIES/MODEL: 3M Safety and Security Film