Superstrut. Metal Framing. Surface Raceway and Lighting Systems
|
|
- Esther Dorsey
- 5 years ago
- Views:
Transcription
1 Material Superstrut electrical raceway, fixture hanging channel, closure strip and accessories are manufactured from hot rolled strip steel. Standard finish for the accessories is GoldGalv. Design Data Deflections at various hanger rod spacings for raceway channels based on 40 to 45 lb. per fixture. Deflection Channel at 10 ft. (in.) at 12 ft. (in.) at 14 ft. (in.) A1200 1/4 1/2 3/4 C1200 * 3/8 3/4 A1400 * Deflection Channel at 6 ft. (in.) at 7 ft. (in.) at 9 ft. (in.) B1200 3/8 9/16 5/8 B /2 * *Not recommended for this spacing. Electrical Raceway Superstrut channel together with snap-in closure strip is listed by Un derwrit ers Laboratories as a surface metal race way. Other accessories listed by Underwri ters Laboratories are iden ti fied on the drawings. Wire Size AWG With or Without KO A1200 A1400 Maximum Number of Wires Raceway B1200 B1400 C1200 E1200 H1200 A B A B A B A B COLUMN A: Suitable for number of wires indicated when used as a raceway. Also suitable for number of wires indicated when installed to support and supply electrical fixtures when race way wiring is suitable for not less than 75 C. By providing clearance between fixture and raceway of not less than 1/2 in., where suitable for 60 C may be used. COLUMN B: Suitable for number of wires indicated when used as a raceway. Also suitable for number of wires indicated when installed to support electrical fixtures when clearance of not less than 1/8 in. is provided between race way and fixture and when wiring is suitable for 75 C. Applicable Channels A1200 B1200 A1200-KO B1400 A1400 C1200 A1400-KO E1200 H1200 A48
2 Fixture Fittings 802 Raceway Joiner With Reinforcing Plate 822 Raceway Joiner & Seal A213 Inside Joiner Furnished complete with nuts. A802EG A Series 158 B802EG B Series 112 E802EG E Series 170 H802 H Series End Cap With Knockout Furnished complete with 1/4 in. x 5/8 in. machine screws and AB100-1/4 nuts. Cat. No. A (in.) For Channel Wt./C lb. A /16 A Series 75 B822 7/8 B Series Tapped End Cap For A1200 Series channel. Only available in GoldGalv finish. Channel Hanger KO for 1/2 in. conduit. Furnished complete with 1/4 in. x 5/8 in. flat head machine screw and AB100-1/4 nut. A805EG A Series 21 H805EG H Series 31 L Channel Hanger - Long 12 ga. steel. For 3/4 in. or 1 in. conduit. Furnished complete with 1/4 in. x 5/8 in. flat head machine screw and AB100-1/4 nut. Rod Size For Channel Wt./C lb. A809-3/4EG A Series 2 E809-3/4EG E Series 26 Channel Hanger Use hanger rod 3/8 in. or 1/2 in. Use with A, AR, B, BR or C Series single channel. Wt./C 25 lb. L Channel Hanger - Long Long type for all Series channel. Wt./C 48 lb. Illustration showing with nut and bolt furnished to attach to fluorescent fixture. Use with A, B, C or D Series channel. Wt./C 34 lb. Illustration showing L with nut and bolt furnished to attach to fluorescent fixture. Use with E and H Series channel as well as A, B, C or D Series channel. Wt./C 51 lb. A49
3 Pre-Gavanized Steel Closure Strip AB844PGC AB844PGCWH White Epoxy Powder Coated Plastic Closure Strip AB844PC Color : Gold AB844PCGY Color : Grey Fixture Fittings 1-5/8 When used as a raceway, channel is normally installed with the slot up. After wiring has been completed the closure strip is installed. For all channels. Standard length: 10 ft. Stainless Steel Closure Strip AB844SS6CS in. (10 feet) AB803 Cast Conduit Connector Side view AB815 Swing Connector Front view AB Swivel Note: Strapping not included /4 To connect 1/2 in. or 3/4 in. conduit to raceway channel. Furnished complete with stud nuts and hex nuts. Part has removable bushing to increase size from 1/2 in. to 3/4 in. Wt./C 60 lb. AB867 Spacer Nuts and bolts to clamp to channel is included. For 1/2 in. or 3/4 in. conduit. Wt./C 95 lb. AB866 Wiring Stud Nut Nuts and bolts to clamp to channel included. For 1/2 in. or 3/4 in. conduit. Wt./C 25 lb. 1-1/8 For use with AB866 wiring stud nuts. Wt./C 24 lb. 1/2 in. Pipe thread Wt./C 21 lb. 811 Stud Nut 812 Stud Nut AB868 Fiber Retainer for Cables Until Closure Strip is In stalled 811-1STR 1/4 x STR 1/4 x 1-1/4 9 For attaching fixture to slot down channel or to slot up knockouts. Specify length. Hex nut included EG 1/4 x 1 6 Wt./C 3 lb. STD. PACK 100 1/32 1-1/2 1-3/8 A50
4 Kindorf Channel Boxes and Receptacles G2000 G2001 G2002 Finish - GoldGalv Wt./C 110 lb. G2003 Finish - GoldGalv Wt./C 120 lb. G2004 Finish - GoldGalv Wt./C 120 lb. G1038 Duplex Outlet Finish - GoldGalv Wt./C 130 lb. G1038A Single Outlet Finish - GoldGalv Wt./C 140 lb. G1038D Raceway Outlet Complete unit including housing, standard DUPLEX 3-wire, 15 Amp., 125 volt, ground receptacle and cover plate. Finish - GoldGalv Wt./C 55 lb. G1038E Raceway Outlet Complete unit including housing, standard SINGLE 3-wire, 15 Amp., 125 volt, ground receptacle and cover plate. Finish - GoldGalv Wt./C 50 lb. G1038B Housing Only Complete unit including housing, duplex, 3-wire, 15 amp., 277 volt-twistlock receptacle and cover plate. Finish - GoldGalv Wt./C 60 lb. G1038C Duplex Cover Plate G1038CA Single Cover Plate Complete unit including housing, single, 3-wire, 15 amp., 277 volt-twistlock receptacle and cover plate. Finish - GoldGalv Wt./C 50 lb. G1038CX Blank Cover Plate Finish - GoldGalv Wt./C 25 lb. Finish - GoldGalv Wt./C 12 lb. Size of opening: diameter Finish - GoldGalv Wt./C 14 lb. Finish - GoldGalv Wt./C 15 lb. A51
5 Kindorf Fixture Accessories G1017 Mercury Vapor Hanger G972HB1/2 Steel Fixture Hanger Adapter AB844 Closure Strip 1-11/16 A / /64 1-1/8 dia. hole = 3/4 KO G-972-1¼2 Nipple G-972-HB-1/2 & G-972-HB-3/4 Fixture Hanger Adapter Finish - GoldGalv To support high or low bay mercury vapor or heavy incandescent fixtures from raceway channels. Permits plug-in connections with G-1038 raceway outlets Used with Channel Depth (in.) Wt./C lb. A /4 76 Electrical Appllications 2 Finish - GoldGalv The hanger adapter securely mounts the fixture hanger or box to the channel through the 1/2 in. KO in the base. No special tools are needed for installation of fittings and fixtures. Superstrut channels, with 1/2 in. KO s every 6 in., hangs and feeds the fixtures thereby simplifying installation. Wt./C 17 lb. Fixture Hanger Fixture Box and Fixture AB288 E ES145 A1200P A52
6 Electrical Appllications 822 G1038D H AB844 AB803 AB AB A53
7 Electrical Appllications E A1200S G2004 G1038D G2003 AB844 A54
Superstrut. Metal Framing. Surface Raceway and Lighting Systems. Material. Design Data. Electrical Raceway
Material Superstrut electrical raceway, fixture hanging channel, closure strip and accessories are manufactured from hot rolled strip steel. Standard finish for the accessories is GoldGalv. Design Data
More informationNonmetallic T&B Surface Raceway
Nonmetallic Two-Piece System Office White The T&B Two-Piece system is designed to contain everything from THHN conductors to coaxial cable. Made of UL listed 94V-0 PVC, T&B Nonmetallic Surface Raceway
More informationInstallation Instructions MODEL VSTI-A020 Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Versa Steel Inc. Guide Cables No
Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Guide Cables No Guide Cables 1 August 4, 2011 Assembly Instructions: (Shown with a 2 board, 12 ft kit) ITEM NO. PART NUMBER DESCRIPTION
More informationNHR Powder Feed Hopper
Instruction Sheet P/N 0804A0 NHR-8-50 Powder Feed Hopper Description This instruction sheet provides specifications, installation and operation instructions, and parts lists for the NHR-8-50 powder feed
More informationK Page 1 of 48 Air Intake - Pg. 17
K532-53168 Page 1 of 48 Air Intake - Pg. 17 Ref # Part Number Qty Description 24 25 041 06-S 1 Gasket, elbow 25 48 054 09 1 Elbow, air cleaner Discontinued not available at Kohler Co. 35 277116-S 1 Brace,
More informationB-Too Drilling and Tapping Machine
Material Specifications Powered by hand or with Ridgid 690 (TM-29) High strength, modular aluminum and steel components Inserts any 3 /4" to 1" corporation stop under pressure Extracts threaded corporation
More informationHANGERS & SUPPORTS CLIP-IT CLIP-IT STUD STRAPS BAR JOIST CLIP CONDUIT HANGERS CLIP-IT
62 hangers & supports Innovation. It s what Madison is all about. Check out our Madison Strap, the product that started it all. Invented in 1929 by our founder Earl Adkinson, Madison has been on the cutting
More information5. STRUCTURAL ANALYSIS
5. STRUCTURAL ANALYSIS The skeletal structure of the experiment casing is constructed from UNISTRUT with all experiment equipment mounted by UNISTRUT provided fasteners. All maximum loads for nuts, bolts,
More informationPVC Electrical Fittings & Accessories Price List
PVC Electrical Fittings & Accessories Price List Effective August 26, 2002 Electrical Products PVC Electrical Fittings & Accessories Price List PVC Electrical Standards 2 Schedule 40 Fittings: Couplings,
More informationNHR-X-X Encore Feed Hoppers
Instruction Sheet P/N 60986-0 NHR-X-X Encore Feed Hoppers WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation.
More informationI.H.S INSTALLATION INSTRUCTIONS
I.H.S INSTALLATION INSTRUCTIONS TOOLS REQUIRED The following tools will be required for installation of your I.H.S. system. Item Qty Needed 9/16 Open End Wrench 2 3/4 Open End Wrench 1 1/2 Open End Wrench
More informationD. ACCESSORIES ADAPTER KITS IMPELLER & SEAL INSTALLATION TOOLS CARRYING HANDLES & LIFT CORDS GALVANIC PROTECTION KITS MUSHROOM STRAINER
. ACCESSORIES AAPTER KITS IMPELLER & SEAL INSTALLATION TOOLS CARRYING HANLES & LIFT CORS GALVANIC PROTECTION KITS MUSHROOM STRAINER SLUGE STRAINERS NEMA 4 WATERTIGHT CONTROL & UAL LEVEL CONTROL (Replaces
More informationDescriptions INCLUDES (2) 1500WC WIRE CLIP; WITH 1/2 INCH, 3/4 INCH CONCENTRIC KNOCKOUT ON BASE
3804 South Street 75964-7263, TX acogdoches Phone: 936-569-7941 Fax: 936-560-4685 1542D STL Junction Box 1500 Wiremold/Legrand Catalog umber Manufacturer Description Weight per unit Product Category Features
More informationSection 9 COYOTE Closures & Splice Cases for OPGW & ADSS
COYOTE Closures & splice cases for OPGW & ADSS: Section 9 Section 9 COYOTE Closures & Splice Cases for OPGW & ADSS Table of Contents COYOTE Closures and Splice Cases for OPGW and ADSS...9-2 COYOTE Closures
More informationSLIDING RAIL SYSTEM 208-580-1904 www.fishfighterproducts.com FFP sliding Rail system The FFP Sliding Rail system will allow you to easily adjust the location of your rod holders, tackle trays, or just
More informationMeter, PD Series, E3 S6, S7 All Parts List
Issue/Rev. 0.0 (3/13) Meter, PD Series, E3 S6, S7 All Parts List Bulletin PO01005 32 68 29 17 68 16 14 19 15 68 20 54 22 18 24 58 23 10 59 41 31 56 55 57 47 52 25 27 34 34 26 40 67 44 39 The Most Trusted
More informationEncore PE 50-lb Feed Hopper
Instruction Sheet P/N 160429-01 Encore PE 50-lb Feed Hopper WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related
More informationBoxes & Mounting Accessories 10-1
Boxes & Mounting Accessories 10-1 ROUND BOXES & ROUND COVERS 3-1/2 ROUND BOXES 4 Hole and 6 Hole Body Side Back Cover Mtg. Pipe holes hole hole Lugs Plugs Thread Size 29 4 1 1 4 27 4 1 1 2 4 27 75 4 ROUND
More informationMaterials: Rigid PVC body, PVC end plugs, PVC reinforcement cuff, Stainless steel cuff bands
PVC PRESSURE VESSELS AMI.5 DIAMETER, 00 PSI, U-PIN STYLE Attractive.5 PVC pressure vessels available for 14, 1 & 40 length membranes. This style is designed for direct connection to /Applied Membranes
More informationGAS DISTRIBUTION PRODUCTS TRANSITION FITTINGS
GAS DISTRIBUTION PRODUCTS TRANSITION FITTINGS CONTINENTAL INDUSTRIES, INC. The Ultimate Connection CONTINENTAL INDUSTRIES, INC. ABOUT US THE ULTIMATE CONNECTION Our Company Continental Industries, Inc.,
More informationAMTEC SUPPORT GRIPS STANDARD, HEAVY DUTY & CONDUIT GRIPS
AMTEC SUPPORT GRIPS STANDARD, HEAVY DUTY & CONDUIT GRIPS DESIGNED TO HOLD THE WEIGHT FOR ELECTRICAL CABLE AS IT HANGS IN VERTICAL, SLOPING OR HORIZONTAL POSITIONS. EASILY INSTALLED AND REMOVED USING NO
More informationNominal Wall Thickness Steel Only in. (mm) Outside Diameter With PVC in. (mm)
PVC-Coated Conduit The ultimate in corrosion protection! OCAL-BLUE Conduit Hot-dip galvanized steel or aluminum conduit. Nominal.00 ( mils) blue urethane coating on interior. Hot-dipped galvanized threads
More informationMeter, PD Series, E3 S1 and E4 S to Present Parts List
Issue/Rev. 0.0 (2/13) Meter, PD Series, E3 S1 and E4 S1 2005 to Present Parts List Bulletin PO01002 9 35 3 39 53 55 57 56 52 54 26 32 37 25 68 48 38 The Most Trusted Name In Measurement 5 31 7 44 42 16
More informationContinental Industries TRANSITION FITTINGS or FAX Visit
Continental Industries TRANSITION FITTINGS 1-800-558-1373 or FAX 1-800-788-1668 Visit www.conind.com ABOUT US Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and
More informationInstallation/Care/Use Manual Soft Sides Fountains with FLEXI-GUARD
Installation/Care/Use Manual Soft Sides Fountains with FLEXI-GUARD EDFP217C EDFP217RAC Installer To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING
More information7 FORAGE AND HARVESTING
Sickle Assemblies 4560R2 Sickle section, 3" x 3-1/4" underserrated. X-Hvy gauge, Chrome finish. Uses rivet RIV101. 142669H L. FT, SECTION NUMBER 141198, TYPE UND 14260 STEEL HEAT THREADED HEADS. Section
More informationSECTION 2 RING MOUNT
SECTION 2 RING MOUNT Rotax aircraft engines are manufactured and supported by Rotax GmbH of Austria. Read and understand the Rotax manuals completely before starting with the engine installation, as they
More informationWELL COMPLETION & PROTECTION. www. .com MINERAL EXPLORATION ENVIRONMENTAL GEOTECHNICAL GEOTHERMAL ROTARY SONIC HDD
WELL COMPLETION & PROTECTION MINERAL EXPLORATION ENVIRONMENTAL GEOTECHNICAL GEOTHERMAL ROTARY SONIC HDD www..com WELL COMPLETION & PROTECTION TABLE OF CONTENTS TABLE OF CONTENTS (FLUSHMOUNTS)... 2-5 MONITORING
More information1500 Follow Spot Yoke
1500 Follow Spot Yoke Rev 1.1 2004 City Theatrical, Inc. Getting Started with the City Theatrical Follow Spot Yoke Congratulations on the purchase of your City Theatrical Follow Spot Yoke. The City Theatrical
More informationHalsey Taylor Owners Manual
Halsey Taylor Owners Manual Wall Mount Steel Refrigerated Fountains INSTALLER These series fountains are among the easiest to install Fountains on the market today. To assure you install these models easily
More informationHalsey Taylor Owners Manual
Halsey Taylor Owners Manual Non-Refrigerated Fountains OVL-EBP OVL-SBP OVL-SEBP OVL-ESBP Installer To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE ITRUCTIO BEFORE STARTING
More informationCHANNEL & SUPPORT SYSTEMS
Total Cable Management Solutions CHANNEL & SUPPORT SYSTEMS Unitrunk Intelok Channel is a strong, easy to erect support system, ideal for supporting cable trays, cable ladders, pipes and ducting and is
More informationCarlon Non-Metallic Boxes
In this section... Carlon Non-Metallic Boxes Carlon Non-Metallic Boxes Overview... A-68 A-69 Carlon Blue PVC Boxes... A-70 A-76 Carlon SuperBlue Boxes... A-77 A-79 Polycarbonate Boxes... A-80 A-91 Phenolic
More informationParts Manual. Scraper Hitches PH:
Parts Manual Scraper Hitches 12-18 1 Table of Contents A123299 Swivel Hitch 3 A1063527 Super Swivel Hitch 4 A125056 Yoke Hitch 5 A125057 Super Capacity Hitch 6 A125223 MDU Hitch 7 A123224 360 Swivel Hitch
More informationFord Service Saddles and Tapping Sleeves
Section AA 5/2001 Ford Service Saddles and Tapping Sleeves The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 219/563-3171 FAX: 1-800-826-3487
More informationContinental Industries STEEL SERVICE TEES or FAX Visit
Continental Industries STEEL SERVICE TEES 1-800-558-1373 or FAX 1-800-788-1668 Visit www.conind.com ABOUT US Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and
More informationBinks SG-2 Plus TM 2 QT. PRESSURE CUPS Model No (Standard) Model No (with OscillatingAgitator)
INTRODUCTION Binks SG-2 Plus TM Pressure Cup is ideal for component spraying and industrial applications where small batch production spraying is required. The 2 qt. capacity is sufficient to complete
More informationa division of Enviro Safety Products
www.minutemanvac.com, a division of Enviro Safety Products.800.637.6606 Chassis 3 4 5 3 4 6 7 8 5 0 0 6 8 0 7 4 3 5 6 7 E 7e www.minutemanvac.com, a division of Enviro Safety Products.800.637.6606 Page
More informationWALL BRACKETS WALL BRACKETS PDI-179C. PDI-179 Bunting. see diagram next page PDI B-1
PDi-B 500). Bracket has four mounting holes for attachment to reinforcing plates or directly into solid backing in wall. Permanently lubricated oillite pivot bushing. Standard bushing size in 5/8,1/2 is
More informationIdeal 6000 Parts Manual
Ideal 6000 Parts Manual SIP Corporation 2006-2008 All Rights Reserved Part Number 20040-8303 SN 60501-60509 Contents Contents...2 Introduction...2 Door...3 Table...4 Front Grinding Head...6 Top Grinding
More informationStandard Hangers and Adapters
Standard s and Adapters Cable Gripping Tabs Prevent cable slippage without the need for a permanently installed hoisting grip. Pre-Assembled and Captivated Hardware Eliminates the need for field assembly.
More informationMini Channel & Fittings
Our mini channels and fittings provide for an economical method of supporting light load requirements on a strut system. Channel Channels are cold formed on our modern rolling mills from 18 Ga. (1.2 mm)
More informationOUTER RACE SHIM SPACERS METRIC OUTER RACE SHIM SPACERS. All Dimensions in Millimeters. Material:300 Series Stainless Steel
OUTER RACE SHIM SPACERS Material:300 Series Stainless Steel METRIC OUTER RACE SHIM SPACERS All Dimensions in Millimeters Material:300 Series Stainless Steel 6-16 INNER RACE SHAFT SPACERS 3 /32" To 1 /2"
More informationChannel Nuts & Hardware
Channel Nuts Channel nuts are one of the main components of our strut system. It is designed to provide essential gripping power and ease during installation. Channel nuts are press formed, machined and
More informationDual Electronic Basketball System Owners Manual
Dual Electronic Basketball System Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. WARNING! READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT.
More informationW A L D M A N U F A C T U R I N G C O M P A N Y, I N C.
A Axle & Nut Assemblies 22 Axle Sets 22 Axles 22 B Bars, Handle 12,13 Basket Fittings 10 Baskets 7,8,9,10 Bolts, Binder 15 Bolts, Expander 15 Bolts, Fork Crown 17 Bolts & Nuts, Assorted 21 Bolts & Nuts,
More informationSpeciÞcations. Engine Dimensions Dimensions in millimeters. Inch equivalents shown in [].
SpeciÞcations Engine Dimensions Dimensions in millimeters. Inch equivalents shown in []. Ê ßÔ Ê ÛÝ Ñ Ê Û ÎÊ Û É 5 ENGINE IDENTIFICATION NUMBERS Kohler engine identiþcation numbers (model, speciþcation
More informationMUELLER. A Wall Type. Indicator Post. Reliable Connections. General Information 2. Technical Data/ Dimensions 3. Installation 4-5.
Installation Instructions manual MUELLER table of contents PAGE A-20814 Wall Type General Information 2 Technical Data/ Dimensions Installation 4-5 Maintenance 6 Parts 7 Indicator Post! WARNING: 1. Read
More informationECP Series Explosionproof Enclosures for OEM Applications. Optimized design, extensive sizes, and fast lead times.
ECP Series Explosionproof Enclosures for OEM Applications Optimized design, extensive sizes, and fast lead times. ECP Series Explosionproof Enclosures, the latest addition to our portfolio of electrical
More informationATV 90 Y-12 YOUTH 2-STROKE RED (A2004ATB2BUSR) Page 1 of 52 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY
2004 ATV 90 Y-12 YOUTH 2-STROKE RED (A2004ATB2BUSR) Page 1 of 52 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY 2004 ATV 90 Y-12 YOUTH 2-STROKE RED (A2004ATB2BUSR) Page 2 of 52 A-ARM, FLOOR PANEL, AND BUMPER
More informationPage 1 of 1 04/19/13 SBR
Office of Roadway Engineering - Plan Insert Sheets Number Title Date Number Title Date Number Title Date 201015 Extension of Anchor Bolts 07/20/12 207000 Bikeway Pavement Marking Details 01/18/13 202010
More informationCLEANROOM GEL GRID CEILING SYSTEM PRODUCT DATA Division
5023 HAZEL JONES ROAD, BOSSIER CITY, LA 71111 888.315.1561 800.877.8746 FAX SALES@GORDONCLEANROOM.COM GORDONCLEANROOM.COM AN EMPLOYEE OWNED COMPANY CLEANROOM GEL GRID CEILING SYSTEM PRODUCT DATA Division
More informationInvacare Top End Parts Catalog
Invacare Top End Parts Catalog T Titanium Top End Frames / Standard Parts Pre- July 2009 20 22 0 2 Pre- July 2009 9 2 2 Pre- July 2009 9 2 Titanium Head Tube Assembly see Casters / Forks on pg. 4 4 4 see
More informationRev J Terminator Parts Book Page 1 of 15 Top End
1181387 Rev J.2016.03.22 Terminator Parts Book Page 1 of 15 Top End 1181387 Rev J.2016.03.22 Terminator Parts Book Page 2 of 15 Top End (800) 532-8677 (727) 522-8677 fax: (727) 522-1007 Terminator: Frame
More informationPressure Dump Valve Service Kit for Series 2300 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit
More informationMeter, PD Series, E3 A1, S1 and E4 S1 Prior to 2005 Parts List
Issue/Rev. 0.0 (2/13) Meter, PD Series, E3 A1, S1 and E4 S1 Prior to 2005 Parts List Bulletin PO01001 33 Pre 1994 39 32 31 21 Pre 1994 45 18 48 44 30 78 57 46 Note: Angled housing not shown. The Most Trusted
More informationMUELLER. Mega-Lite Drilling Machine. Reliable Connections. table of contents PAGE. Equipment 2. Operating Instructions 3-4. Parts Information 5
operating Instructions manual MUELLER Mega-Lite Drilling Machine table of contents PAGE Equipment 2 Operating Instructions 3-4 Parts Information 5 Travel Charts 6-11! WARNING: 1. Read and follow instructions
More informationGT21 String Trimmer UT Page 1 of 16 Accessories
GT21 String Trimmer UT-26038 Page 1 of 16 Accessories GT21 String Trimmer UT-26038 Page 2 of 16 Accessories Ref # Part Number Qty S/P/F Description 1 PS01443 1 TOOL KIT 2 DG07819 1 /P STRAP 3 G07830 1
More informationUser Manual 1792 Standing Seam Metal Roof Retractable Swivel Anchor
1 User Manual 1792 Standing Seam Metal Roof Retractable Swivel Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee
More informationPipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
More informationEPOXY FITTINGS DIMENSIONS
Bulletin No. A150 May 1, 2004 EPOXY FITTINGS DIMENSIONS 2"-16" GREEN THREAD fittings may be used with GREEN THREAD and RED THREAD II piping. Refer to Chemical Resistance Guide, Bulletin No. E5615, for
More informationRev S Terminator Parts Book Page 1 of 14 Top E nd
1181387 Rev S.2017.01.17 Terminator Parts Book Page 1 of 14 Top E nd 1181387 Rev S.2017.01.17 Terminator Parts Book Page 2 of 14 Top E nd Terminator: Frame Assembly PER CHAIR Frame Only: Aluminum for Folding
More information44 CE RANGE WATERTIGHT SURFACE-MOUNTING JUNCTION BOXES
WALL BOXES IN GWPLAST 75 - GWT 650 C GWT 650 C TP 85 C WALLS WITH CABLE GLAND - IP44 AND IP55 GW44001 JUNCTION BOXES WITH PLAIN PRESS-ON LID - IP44 - GREY RAL 7035 LxHxD (mm) No. holes / Ø GW 44 001 Ø
More informationThe Tool Box. Lifespan Healthcare, LLC 270 Scientific Drive, Suite #14 Norcross, GA t f
The Tool Box Table of Contents System TOOLS Adapters... 1 Heavy Duty Equipment Rails... 1 Light Duty Equipment Rails... 2 Mounting Hardware... 2 Equipment Shelves and Monitor Mounts... 3, 4 Work Surfaces...
More informationReproduction. Not for 27" & 29" TWO STAGE INTERMEDIATE SNOWTHROWERS Parts Manual for M1227E M1227EX M1529E
Parts Manual for 27" & 29" TWO STAGE INTERMEDIATE SNOWTHROWERS 2011 Model No. Description 1696001 M1227E 1696002 M1227EX 1696003 M1529E Briggs & Stratton Yard Power Products Group 535 Macon Road McDonough,
More informationMeter, PD Series H8-S1, S3, S5, S6, & S7 Parts List
Meter, PD Series H8-S1, S3, S5, S6, & S7 Parts List Issue/Rev. 0.0 (1/14) Bulletin PO01010 S1 S3, S5, S6, S7 The Most Trusted Name In Measurement Inner Mechanism Page 2 PO01010 Issue/Rev. 0.0 (1/14) Item
More informationGel Drop Seal for FOSC 450 Fiber Optic Splice Enclosure Installation Instructions
Gel Drop Seal for FOSC 450 Fiber Optic Splice Enclosure Installation Instructions TECP-30-215 Issue 1 4/2013 INTRODUCTION The Gel Drop Seal device is for use with FOSC 450 B, B Short, C, and D size closures
More informationE10 E10 E10 E10 E10 E10 E10 E10 E10 E10 E10 E10 E10 E10. Cable gland Series 8161/7, 8161/8. Installation Equipment and Accessories E10/1.
> Explosion protection type "Increased safety" > Degree of protection IP68 > Ex e and Ex i versions > Integrated blind plug (accessory) for closing unused cable glands > Cable diameter ranges from 1 to
More informationSLEEVE AND COLLAR MOUNT FREESTALLS
SLEEVE AND COLLAR MOUNT FREESTALLS FREESTALLS-1 FEATURES Hot dipped galvanized or pre-galvanized loop option. Heavy galvanized 3 1/2 post Easy installation Adjustable height Cow friendly loop profile to
More informationOperating Instructions Models and Hydrostatic Test Pumps
Operating Instructions Models 33100 and 33101 Hydrostatic Test Pumps 33100 DIMENSIONS: WEIGHT: PUMP: MOTOR: CONTROL: GAUGE: DISCHARGE HOSE: 16 (40cm) L x 22 (55cm) W x 18 (45cm) H 87 lbs., 39.5 kg Triplex
More informationM2 Antenna Systems, Inc. Model No: VLP16
M2 Antenna Systems, Inc. Model No: 100-600VLP16 SPECIFICATIONS: Model... 100-600VLP16 Frequency Range... 100-600 MHz Cont. *Gain... 9.64 dbi Front to back... 12 db Typical Beamwidth... E=64 / H=70 Feed
More informationAutoDrill s OUTSTANDING FEATURES
PRODUCTION DRILLING & TAPPING SOLUTIONS Reduce Your Costs and Increase Your Production The Affordable, Powerful, Compact Solution AutoDrill s OUTSTANDING FEATURES Self Feeding with Air or Oil Thrust Capacity
More informationElectrical Contractor s. Labor Units Manual
Electrical Contractor s Labor Units Manual EMT CONDUIT & CONNECTORS EMT THINWALL CONDUIT 1/2" 2.75 3.25 3.75 4.13 4.54 C 3/4" 3.00 3.50 4.00 4.40 4.84 C 1" 3.50 4.00 4.50 4.95 5.45 C 1 1/4" 4.00 4.50 5.00
More informationBARNES PROSSER CROWN SERVICE PARTS
MODEL PART NO. SGV3002L 084798 SGV3022L 084799 SGV3062L 084800 SGV3032L 084801 SGV3042L 084802 SGV3052L 088861 SGV5002L 084803 SGV5022L 084804 SGV5062L 084805 SGV5032L 084806 SGV5042L 084807 SGV5052L 088862
More informationParts Manual STRIKER Striker 2840 Parts List - PN Printed in USA 03/18/08
Parts Manual STRIKER 2840 Striker 2840 Parts List - PN 238155 - Printed in USA 03/18/08 Standard Parts Recommended General Wear Parts Ref No Part Description Qty Part No 1 Squeegee Hose Assembly
More informationTripod Setup Guide (M-TPx)
Items needed: 1/2 inch wrench, mast level (M-MLA), medium size wire cutters, crescent wrench, all-purpose grease, tape measure, tie wraps, redi-mix cement (optional), shovel (optional), sledge hammer (for
More informationSCOUT DECK ANCHOR 3 1/4" BONDING SCREW
SCOUT DECK ANCHOR 16" 16" 1" X 4" ANCHOR BOLT (4) 10" 3 1/8" 5" 6" MIN COPPER WIRE TO ATTACH TO BONDING GRID 3 1/4" BONDING SCREW CONCRETE DECK SPECIFICATIONS: THE AQUA CREEK PRODUCTS' SCOUT DECK ANCHOR
More informationInstallation, Operation and Maintenance Manual for Back Pressure Regulator
Installation, Operation and Maintenance Manual for Back Pressure Regulator Model 8860 2009 Groth Corporation IOM-8860 Rev. B 12541 Ref. ID: 95565 Page 2 of 13 Table of Contents I. INTRODUCTION 3 II. DESIGN
More informationSEALED CONNECTORS FOR THE LIMIT SWITCHES
SEALED CONNECTORS FOR THE LIMIT SWITCHES LIST OF MODELS / Sealed connectors are used at the cable-connecting section of limit switches. Type and appearance Materials Features Target market Applications
More informationBUTTERFLY VALVES. Toll Free (877) - ICFLUID -2-
BUTTERFLY VALVES 1. General HyrdoWer is a globally recognized manufacturer of power unit accessories. They have become specialists in the design of Butterfly Valves and Hydraulic Compensators. The shut
More informationHYDRAULIC PUNCH DRIVER 38456, 38520, 7306 / 7306SB, 7310 / 7310SB, 7506, 7606SB, 7610SB, 7625 / 7625Pg / 7625PgSB, 7646 / 7646Pg / 7646PgSB
INSTRUCTION MANUAL HYDRAULIC PUNCH DRIVER 38456, 38520, 7306 / 7306SB, 7310 / 7310SB, 7506, 7606SB, 7610SB, 7625 / 7625Pg / 7625PgSB, 7646 / 7646Pg / 7646PgSB Read and understand all of the instructions
More informationTable Bases. Stainless Steel, Aluminum and Cast Iron Designs
Table Bases Stainless Steel, Aluminum and Cast Iron Designs Features: Our Table Bases are available in Table and Bar heights and most can be cut to any custom height. These bases are strong and durable,
More informationGT20 String Trimmer UT Page 1 of 16 Accessories
GT20 String Trimmer UT-26037 Page 1 of 16 Accessories GT20 String Trimmer UT-26037 Page 2 of 16 Accessories Ref # Part Number Qty S/P/F Description 1 PS01443 1 TOOL KIT 2 DG07819 1 /P STRAP 3 G07830 1
More informationCopper Bonded Ground Rod / Grounding Rods / Copper Bonded Earth Rod / Earthing rods
Copper Bonded Ground Rod / Grounding Rods / Copper Bonded Earth Rod / Earthing rods Copper bonded earth rods are made from low carbon Steel. Earth Rods are molecularly bonded with 99.9% pure electrolytic
More informationOPERATIONS/PARTS MANUAL FOR PATTERSON'S MODEL # WWP40M-LPS-6 LOW-PROFILE BARGE CONNECTOR WINCH
W. W. Patterson Company 3 Riversea Road Pittsburgh, PA 15233 Phone: 800-322-2018 FAX: 412-322-2785 OPERATIONS/PARTS MANUAL FOR PATTERSON'S MODEL # WWP40M-LPS-6 LOW-PROFILE BARGE CONNECTOR WINCH Please
More informationR-3501-E2 R-3501-H4. R-3501-HL Mountable Curb Frame, Grate
For a complete listing of FREE OPEN AREAS and PERIMETERS of all grates, refer to pages 306-311. R-3501-D2A See pages 145-146-148 &155 for additional Roll Type products R-3501-D2A C 1.0 3.4 R-3501-E2 ROLL
More informationSIMPLAIR PIPING TOOL. JXT Company
SIMPLAIR PIPING INGERSOLL-RAND SIMPLAIR PIPING With push-in fittings and lightweight anodized aluminum pipe, a SimplAir system provides ideal connection throughout your entire air distribution system.
More informationMODEL 9875 STADIUM BASEBALL SCOREBOARD. Instruction Manual
UNITEC MANUFACTURING DIVISION MODEL 9875 STADIUM BASEBALL SCOREBOARD (WITH INNING BY INNING SCORING) Instruction Manual Mailing Address: PO Box 260, Yorkville, NY 13495-0260 Plant Address: 34 Main Street,
More informationPOWER TOOL ACCESSORIES MADE FOR THE TRADE! KNOCKOUTS BENDING. Voltage Detector, Non-Contact GT-12A V with Audible Alarm and Bright LED s
TESTING POWER TOOL ACCESSORIES KNOCKOUTS Voltage Detector, Non-Contact GT-12A 50-1000V with Audible Alarm and Bright LED s 34401 34403 34411 36414 BENDING 555 Classic Electric Bender 555C Bender Only 555RSC
More informationPart No (Low Changeover) Part No (High Changeover) Part No (High Changeover)
ELX-S TM UNIT 60% 665020 (Low Changeover) 305274 (High Changeover) 305305 (High Changeover) IMPORTANT: This catalog is published as an aid in identifying the detail parts that make up this complete device.
More informationPlok. Rapid Mating Multi-Pin Industrial Connector. Amphenol Industrial Sine Systems * Pyle Connectors Corporation
- Plok Rapid Mating Multi-Pin Industrial onnector mphenol Industrial Sine Systems * Pyle onnectors orporation eatures and enefits Rapid mate spring loaded, push to mate, pull to unmate coupling system
More informationPARTS: AIRPREP AFTERCOOLERS AND AIR DRYERS
PARTS: AIRPREP AFTERCOOLERS AND AIR DRYERS MOTOR AND FAN PARTS ITEM/MODEL ACS/ADS 250 ACS/ADS 400 ACS/ADS 750 ACS/ADS 950 ACS/ADS 1200 ACS/ADS 1600 Air motor 1300-040-03 1300-040-03 1300-040-03 1300-090-03
More informationRANGER PROP BUILDING INSTRUCTIONS & PHOTOS
RANGER PROP BUILDING INSTRUCTIONS & PHOTOS Science under the ice Ice sheet At the international competition, the science under the ice product demonstration will take place under an actual sheet of ice.
More informationReplaces Lesco 300 & 500 Parts Cutting Unit
Replaces Lesco 300 & 500 Parts 3A 11 10 10 11 17 3 1 15 2 13 1 20 1 20 1 21 2 2 22 1B 30 1A 10 14 31 25 23 24 10 4 27 23 25 26 14 24 10 13A 5 5A 4A 16 0 R&R Reels Available, Lifetime Guaranteed 1 R50271
More informationBRINGING YOU THE SINCE 1980
BRINGING YOU THE QUALIT Y YOU DESERVE SINCE 1980 2 0 16 P R O D U C T C ATA LO G A Division of Vermont Precision Tools, Inc. QUALITY POLICY Our policy is to consistently achieve or exceed customer satisfaction
More informationPressure Dump Valve Service Kit for Series 3000 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 000 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00, 400, 500, and 700 applicator
More informationGRAVITY BIKE RACK ASSEMBLY & OPERATING INSTRUCTIONS
GRAVITY BIKE RACK 94479 ASSEMBLY & OPERATING INSTRUCTIONS Due to continuing improvement, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011
More informationCOMPACT TRIPLE WALL OUTLET STATION MODEL INSTALLATION AND OPERATING INSTRUCTIONS
COMPACT TRIPLE WALL OUTLET STATION MODEL 6255-1 INSTALLATION AND OPERATING INSTRUCTIONS To assure safe operation and conformation to local fire codes, all Porter Outlet Stations are designed to be used
More informationFI-25V OWNER S MANUAL
OWNER S MANUAL SIDE VIEW INSIDE VIEW - CONTROL PANEL 04/18/07 PARTS LIST ITEM PART NO. DESCRIPTION 1 2 TANK25 DFP8 25 GALLON MOLDED TANK 8 CAP FOR 25 GALLON TANK 3 4 H34-30 HBSS1234 FOAM DISCHARGE HOSE
More informationBARRIER OFFSET 0" A 6" 6" A 12" 12" A 26" A 26" 3A OR 4A L OR S * ** L OR S L OR S
ACCEPTABLE (TCB) TYPES AND ANCHORING DETAILS BASED ON UNDERLYING SURFACE TYPE AND BARRIER OFFSET FROM DROP-OFF BARRIER OFFSET UNDERLYING SURFACE 0" A 6" 6" A 12" 12" A 26" A 26" TCB TYPE DETAIL TCB TYPE
More information