Certificate of Compliance

Transcription

1 Certificate of Compliance Certificate: Master Contract: Issued to: Brodie Meter Company, LLC Highway 301 North Statesboro, GA USA Attention: Jonathan Whitten The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US or with adjacent indicator 'US' for US only or without either indicator for Canada only. Issued by: Dorel Stefan Dorel Stefan PRODUCTS CLASS PROCESS CONTROL EQUIPMENT - For Hazardous Locations CLASS PROCESS CONTROL EQUIPMENT - For Hazardous Locations - Certified to US Standards Class I, Division 1, Groups C & D BiRotor Plus Models B271, B274, B281, B284 and B291 Volumetric Flow Meters; Rated 9-28Vdc, 5W Class 2; Ambient Temperature range -40 C to +60 C; Maximum Process Pressure for B271, B281 and B291 of 1964kPa (285psi) or for B274 and B284 of 5099kPa (740psi). Enclosure Type 4X/IP65, Temperature codes of T6 or T4 (high temperature process fluid model) Model code: Bxyz9abcdefghjk B=BiRotor Plus xy - Flow Rate 27=Std 425 US gpm/1609 lpm, intermittent 550 US gpm/2081 lpm, pipe size 3 28=Std 700 US gpm/2650 lpm, intermittent 1000 US gpm/3785, pipe size 4 DQD 507 Rev Page: 1

2 29=Std 1000 US gpm/3785 lpm, intermittent 1200 US gpm/4542 lpm, pipe size 6 z - Maximum Process Pressure - MWP 1=285psi 4=740psi (only options 27 and 28) 9 - Revision C=BiRotor Plus a - Meter Output Temperature of Process: -20 C to 75 C std A=One Pickoff w/dual Channel Preamp B= Two Pickoffs w/dual Channel Preamp C= One Pickoff only D=Two Pickoffs only Temperature of Process: -10 C to 110 C (High Temp.) E= One HT Pickoff w/dual Channel Preamp F= Two HT Pickoffs w/dual Channel Preamp G= One HT Pickoff only H= Two HT Pickoffs only b - Elastomers: Process Wetted Materials (any alpha character A-Z, not relevant to certification) c - Connection Type, Flange A=ANSI 150# B=ANSI 300# C=DIN PN 16 D=DIN PN 40 d - Accuracy/Flow Range (any alpha character A-Z, not relevant to certification) e - Rotors/Bearings (any alpha character A-Z, not relevant to certification) f - Additional Measurement A=none g - Weights and Measure Approvals (any alpha character A-Z, not relevant to certification) h - Hazardous Area Approvals B=USA and Canada (Class I Groups C and D) j - Additional Accessories - Register Mounting 1=none k - Material Certification and Pressure Documentation (any alpha character A-Z, not relevant to certification) DQD 507 Rev Page: 2

3 Low Temperature BiRotor Plus Models LB271, LB274, LB281, LB284 and LB291 Volumetric Flow Meters; Rated 9-28Vdc, 5W Class 2; Ambient Temperature range -40 C to +60 C; Maximum Process Pressure for LB271 LB281 and LB291 of 1964kPa (285psi) or for LB274 and LB284 of 5099kPa (740psi). Enclosure Type 4X/IP65, Temperature codes of T6. Model code: LBxyz9abcdefghjk LB=Low Temp BiRotor Plus xy - Flow Rate 27=Std 425 US gpm/1609 lpm, intermittent 550 US gpm/2081 lpm, pipe size 3 28=Std 700 US gpm/2650 lpm, intermittent 1000 US gpm/3785, pipe size 4 29=Std 1000 US gpm/3785 lpm, intermittent 1200 US gpm/4542 lpm, pipe size 6 z - Maximum Process Pressure - MWP 1=285psi 4=740psi (only options 27 and 28) 9 - Revision A=Low Temp BiRotor Plus a - Meter Output Temperature of process: -40 to 75 C A=One Pickoff w/dual Channel Preamp B= Two Pickoffs w/dual Channel Preamp C= One Pickoff only D=Two Pickoffs only b - Elastomers: Process Wetted Materials (any alpha character A-Z, not relevant to certification) c - Connection Type, Flange A=ANSI 150# B=ANSI 300# C=DIN PN 16 D=DIN PN 40 d - Accuracy/Flow Range (any alpha character A-Z, not relevant to certification) e - Rotors/Bearings (any alpha character A-Z, not relevant to certification) f - Additional Measurement A=none g - Weights and Measure Approvals (any alpha character A-Z, not relevant to certification) DQD 507 Rev Page: 3

4 h - Hazardous Area Approvals B=USA and Canada (Class I Groups C and D) j - Additional Accessories - Register Mounting 1=none k - Material Certification and Pressure Documentation (any alpha character A-Z, not relevant to certification) APPLICABLE REQUIREMENTS Canadian Requirements CSA Std C22.2 No 0-M91 CSA Std. C22.2 No CSA Std C22.2 No 30-M1986 CSA Std C22.2 No 142M1987 CSA Std C22.2 No CSA Std C22.2 No US Requirements ANSI/UL Std th Ed. ANSI/UL Std th Ed. ANSI/UL Std 50 12th Ed. ANSI/UL Std 50E 1st Ed. The following standard(s) were used in whole or in part as a guideline. IEC Ed. 2.1 NEMA MARKINGS General Requirements - Canadian Electrical Code, Part II Threaded Conduit Entries Explosion-Proof Enclosures for Use in Class Hazardous Locations Process Control Equipment Enclosures for Electrical Equipment, Non- Environmental Considerations Enclosures for Electrical Equipment, Environmental Considerations Industrial Control Equipment Explosion-Proof and Dust-Ignition-Proof Electrical Equipment For Use in Hazardous (Classified) Locations Enclosures for Electrical Equipment, Non- Environmental Considerations Enclosures for Electrical Equipment, Environmental Considerations Degree of Protection Provided by Enclosures (IP Code) Enclosures for Electrical Equipment (1000 Volts Maximum) The following markings are provided on multiple 300 series stainless steel painted, stamped and etched nameplates. The stainless steel plate is attached to the flow meter by means of two or four stainless steel drive screws. See drawings ENG , ENG , ENG , ENG and ENG submittor's name: Brodie Meter Co LLC or DBA Brodie International or CSA Master Contract Number xxxxxx, adjacent to the CSA Mark in lieu of manufacturers name. model designation: As specified in the PRODUCTS section above. electrical rating: As specified in the PRODUCTS section above. DQD 507 Rev Page: 4

5 maximum process pressure; As specified in the PRODUCTS section above. ambient temperature range: As specified in the PRODUCTS section above. Enclosure: As specified in the PRODUCTS section above. hazardous locations designations: As specified in the PRODUCTS section above. date code or equivalent; The CSA Mark with or without C and US indicators, as shown on the Certificate of Conformity. WARNING - TO PREVENT IGNITION OF HAZARDOUS ATMOSPHERE, DISCONNECT ALL SUPPLY CURCUITS, AND INSURE THE AREA IS NON-HAZARDOUS BEFORE OPENING, KEEP COVER TIGHTLY CLOSED WHEN IN OPERATION, CONDUIT SEALS MUST BE INSTALLED WITHIN 18 INCHES OF THE ENCLOSURE ADVERTISSEMENT: POUR EVITER D ENFLAMMER DES VAPEURS DANGEREUSES, COUPRI TOUTES LES ALIMENTATIONS ET S ASSURER QEU L EMPLACEMENT N EST PAS DANGEREREUX ANAVT D OUVRIR. PENDANT L UTILISATION, S ASSURER QUE LE COUVERCLE EST BIEN FERM. POSE DES RACCARDS DE SCELLEMENT AU PLUS 475 MM BOITER. Note - Jurisdictions in Canada may require these markings to also be provided in French language. It is the responsibility of the manufacturer to provide bilingual marking, where applicable, in accordance with the requirements of the Provincial Regulatory Authorities. It is the responsibility of the manufacturer to determine this requirement and have bilingual wording added to the "Markings". DQD 507 Rev Page: 5