I.H.S INSTALLATION INSTRUCTIONS

Transcription

1 I.H.S INSTALLATION INSTRUCTIONS

2 TOOLS REQUIRED The following tools will be required for installation of your I.H.S. system. Item Qty Needed 9/16 Open End Wrench 2 3/4 Open End Wrench 1 1/2 Open End Wrench or 1/2 Socket with Drive Ratchet 1 3 Prong Extension Cord 1 (Extension cord length will need to run from power receptacle to where you are setting up your I.H.S. system, this will only be used for set up purposes) BASEBALL HOPPER JUNCTION BOX SOFTBALL HOPPER JUNCTION BOX SOFTBALL HOPPER MOTOR 4X4 JUNCTION BOX BASEBALL HOPPER MOTOR BASEBALL AGITATOR BASEBALL HOPPER BASEBALL UPPER EXIT TUBE BASEBALL PINCH ROLLER SOFTBALL PITCHING MACHINE SOFTBALL AGITATOR SOFTBALL HOPPER SOFTBALL UPPER EXIT TUBE SOFTBALL PINCH ROLLER BASEBALL PITCHING MACHINE BASEBALL CHUTE SOFTBALL CHUTE SA-8 LIGHT BOX 2 SOFTBALL AC SPEED CONTROLLER BASEBALL AC SPEED CONTROLLER

3 COIN BOX INSTALLATION CAUTION! WHEN LOADING I.H.S. HOPPER WITH BALLS, EMPLOYEES SHOULD ALWAYS WEAR A BATTING HELMET WITH FACE GUARD AND SOUND A WARNING FOR BATTERS TO LEAVE BATTING STALLS DURING THE LOADING AND MAINTENANCE OF EQUIPMENT THIS EQUIPMENT SYSTEM HAS SEVERAL MOVING PARTS AND HIGH VOLTAGE PRE- SENT WHICH POSE POTENTIAL DANGER TO ANY PERSON SERVICNG OR MAINTAINING IT. BEFORE INSTALLATION, SERVICING OR MAINTAINING EQUIPMENT SYSTEM, YOU MUST REVIEW MAINTENANCE AND SERVICING SECTION OF THIS MANUAL. SERIOUS INJURIES COULD RESULT IF NOT REVIEWED, UNDERSTOOD AND FOLLOWED! COIN BOX INSTALLATION: NOTE: For part identification please refer to the Parts & Accessories section of the manual. Step 1: Mount coin box pole and ABC s Coin Box inside the hitting stall on the right handed batters side, see attached drawing of the cage layout on the last page. Step 2: Route low voltage control cable (Beldon #8723) thru 1/2 EMT or ridged conduit above ground from coin box to light box, located on the I.H.S. Pitching Machine. Step 3: Strip the Control Cable (inside coin box) about 3 from the end of cable, crimp the male insulated quick-disconnect terminals on the black, white & green wires (also crimp the red wire if installing a dual IHS). Connect the terminals as shown in diagram below and zip tie the cable to the black wire-tie block in the back of the coin box. (NOTE: if you have any questions please call ABC s Service Department.) Black (Start) Black (Start) Coin Box Belden Wire White (Coin A) White (Coin A) Red (Coin B) Red (Coin B) Light Box Belden Wire Green (Com) Green (Com) NOTE: MOUNTING HARDWARE FOR COIN BOX AND TERMINAL CONNECTORS FOR BELDEN WIRE ARE SHIPPED INSIDE OF COIN BOX. 3

4 COIN BOX INSTALLATION Route control cable thru pipe (Beldon #8723) Leave 24 min. slack exiting thru hole in center of coin box mounting plate. Coin Box Mount Plate Welded Solidly To Post (Parallel To Cage Side). DO NOT WELD INSIDE CENTER HOLE OF MOUNTING PLATE. Mount Coin Box to Coin Box Plate using (4) 3/8 x 3/4 carriage bolts & lock nuts. 2-1/2 Schedule 40 Pipe F/S TYP J-Box with Watertight (Gasketed) Cover 6 [0.15M] 4-0 [1.22M] 1/2 ridged conduit above ground from coin box to low voltage junction box located behind I.H.S. (Run Control Beldon #8723 ) thru conduit. Concrete post into ground 2 0 (Optional-Flange mount post with 1/4 x 6 steel plate welded to bottom of post, anchored with (4) 3/8 concrete anchor bolts.) 4

5 LIGHT BOX WIRING INSTALLATION: LIGHT BOX INSTALLATION NOTE: Confirm Light Box is not plugged into A/C power (receptacle) Step 1: Feed the Beldon #8723 Control Cable thru the light box strain relief marked Low Voltage. Step 2: Strip Beldon wire #8723 Control Cable about 3 from the end of cable, crimp the male insulated quick disconnect terminals on the black, white & green wires (also crimp the red wire if installing a dual IHS). Connect the male terminals to the female quick disconnect terminals corresponding wire color located at the top left corner on the light box door. Step 3: Close light box door and tighten clamp down. (Make sure not to pinch any wires when closing light box door). 5

6 DUAL HOPPER INSTALLATION THE FOLLOWING STEPS ARE ONLY REQUIRED IF INSTALLING A DUAL MACHINE IHS. IF INSTALLING A SINGLE MACHINE IHS PLEASE PROCEED TO THE PITCHING MACHINE SETUP INSTRUCTIONS. Step 1: Lift the baseball hopper onto the main frame of the IHS and secure by hooks. Step 2: Install and tighten (4) 3/8 x 2 1/2 bolts with flat washers, lock washers, and nuts thru the legs of the baseball hopper and IHS main frame. 6

7 DUAL HOPPER INSTALLATION Step 3: Install the pinch roller assembly and secure with the 4 bolts that hold the white UHMW bushing onto the hopper exit hole, finger tighten the 4 mounting bolts. Step 4: Remove the 4 screws that secure the baseball pinch roller bottom cover. 7

8 DUAL HOPPER INSTALLATION Step 5: Route the Pinch Roller A cord thru the strain relief of the baseball pinch roller box. Connect the black wire of the Pinch Roller A cord to either wire of the pinch roller motor. Connect the white wire of the Pinch Roller A cord to the other pinch roller motor wire. Route the green wire of the Pinch Roller A cord thru one of the holes in the pinch roller bottom cover plate and secure with the self tapping screw on the front side of pinch roller box. Reinstall and tighten the 4 self tapping screws for the bottom cover, tighten pinch roller cord strain relief. Step 6: Loosen the 2 screws holding the faceplate on the baseball hopper junction box located on top of the hopper. Route the baseball hopper motor wire along the square tubing framework of the hopper and into the strain relief of the baseball hopper junction box. 8

9 DUAL HOPPER INSTALLATION Step 7: At the baseball hopper junction box, wire nut the white wire from the baseball hopper motor together with the white wire from the 4x4 junction box cord. Wire nut the green wire from the baseball hopper motor together with the green wire from the 4x4 junction box cord. Connect the black wire from the 4x4 junction box cord to the open terminal connector on the 10 amp resettable circuit breaker located on the side of the baseball hopper junction box. AFTER COMPLETING THESE STEPS PLEASE PROCEED TO THE PITCHING MACHINE SETUP INSTRUCTIONS. 9

10 PITCHING MACHINE SETUP PROCEDURE PITCHING MACHINE SETUP Step 1: Unplug Machine A cord leading from the AC Speed Controller to the Light Box. (see diagram 1) Diagram 1 NOTE: WHEN COMPLETING THIS STEP THE PITCHING MACHINE MOTOR AND WHEELS WILL BE RUNNING, USE CAUTION AND BE AWARE OF MOVING PARTS. Step 2: Plug Machine A male cord end from the AC Speed Controller into an extension cord, extension cord should be plugged into 115 vac outlet. (see diagram 2 ) Diagram 2 Plug directly into an extension cord 10

11 PITCHING MACHINE SETUP PROCEDURE Step 3: Manually drop balls into pitching machine chute to determine where the ball is pitching. (see diagram 3 ). Diagram 3 Step 4: Turn knob clockwise on AC Speed Controller for a faster speed or counter clockwise on the AC Speed Controller for slower speeds until you reach your desired speed. (see diagram 4) Diagram 4 11

12 PITCHING MACHINE SETUP PROCEDURE Step 5: Loosen the 3/4 nut on the hi/low handle. (see diagram 5) Diagram 5 Step 6: Turn the hi/low adjust handle clockwise to raise the pitch or counter clockwise to lower the pitch until you have reached your desired pitch height. (see diagram 6) Diagram 6 Step 7: Tighten the 3/4 nut on the hi/low handle. (see diagram 7) Diagram 7 12

13 PITCHING MACHINE SETUP PROCEDURE Step 8: Loosen the 3/4 nut on the left/right adjuster knob shaft. (see diagram 8) Diagram 8 3/4 NUT Step 9: Turn the left/right knob clockwise to pitch right or counter clockwise to pitch left until you have reached your desired pitch. (see diagram 9) Diagram 9 Step 10: After you have achieved desired pitch location, tighten the 3/4 nut on the left/right adjuster knob shaft. (see diagram 10) Diagram 10 3/4 NUT IF THIS IS A DUAL MACHINE IHS REPEAT THE SAME PROCEDURES FOR MACHINE B BEFORE PROCEEDING TO THE NEXT STEP. 13

14 HOPPER BALL FEED ADJUSTMENT After pitching machine has been set you may have to make minor adjustments for free flow of ball from hopper exit tube to the pitching machine. There is primarily 3 types of adjustment to be made, adjustments listed below. NOTE: DISCONNECT AC SPEED CONTROLLER MACHINE A MALE CORD END FROM EXTENSION CORD BEFORE PROCEDING WITH THE FOLLOWING STEPS. UPPER EXIT TUBE Step 1: Using a 1/2 wrench, loosen the 4 bolts securing the upper exit tube to the bushing. (see diagram 1) Diagram 1 Step 2: Rotate upper/lower exit tube so the ball will drop into the pitching machine chute. (see diagram 2) Diagram 2 Step 3: Using a 1/2 wrench, tighten the 4 bolts securing the upper exit tube to the bushing. (see diagram 3) Diagram 3 14

15 HOPPER BALL FEED ADJUSTMENT GUIDE CHUTE ADJUSTMENT (for Baseball and Softball Fast pitch) Step 1: Using two 9/16 wrenches, loosen the (2) bolts for the guide chute. (see diagram 1) Diagram 1 Step 2: Rotate guide chute up or down to the desired position so that the ball from the lower exit tube drops freely into the guide chute. (see diagram 2) Diagram 2 Step 3: Using two 9/16 wrenches, tighten the (2) bolts for the guide chute. (see diagram 3) Diagram 3 15

16 HOPPER BALL FEED ADJUSTMENT & BALL LOADING GUIDE CHUTE ADJUSTMENT (for Softball Slow pitch) Step 1: Loosen the two allen head bolts that secure the chute to the pitching machine. (see diagram 1) Step 2: Adjust the chute so that it is all the way down in the slot of frame. (see diagram 2) Step 3: Tighten the (2) allen head bolts and nuts that secure the chute to the frame. Bolt should be all the way down in the slot. Diagram 1 Diagram 2 HOPPER BALL LOADING: 1) When loading hopper with balls, employees should sound a warning for batters to leave batting stalls during maintenance of equipment. 2) Batting helmets with face guard should be used at all times when maintaining equipment. 3) Always unplug power to I.H.S. unit when servicing. 4) Never put more than 400 Baseballs or 300 Softballs in hopper at one time. 5) Please review Batting Range Safety and Operations Standards before using equipment. 16

17 LIGHT BOX FINAL SETUP Step 1: Plug AC Speed Controller Machine A male cord end back into the Light Box female cord end Machine A. (see diagram 1) Diagram 1 Step 2: Plug Light Box Power male cord end into 120 vac receptacle. (see diagram 2) Diagram 2 IF THIS IS A DUAL MACHINE IHS REPEAT THE SAME PROCEDURES FOR MACHINE B 17