Level Measurement Point level measurement - Vibrating switches

Transcription

1 Overview Configuration Horizontal mounting Switching point (recommended mounting position, particularly for adhesive applications) Marked with screwed version on top, with flange versions directed to the flange holes Vertical mounting is a standard vibrating level switch for material detection in liquid and slurry applications such as overflow, high, low, and demand applications, as well as pump protection. For use in SIL- applications. Benefits Proven vibrating level switch technology for liquids Compact insertion length of 0 mm (.57 inch) for confined space applications Fault monitoring for corrosion, loss of vibration or line break to the piezo drive Functional Safety (SIL ). Device suitable for use in accordance with IEC 6508 and IEC 65 Hygienic process connections Suitable for API 350 Optional remote test signal conditioner Switching point [approx. 3 (0.5)] Mount away from filling openings or agitators. Switching point with higher density Switching point with lower density Switching point [approx. 7 (.06)] Application is a level switch designed for industrial use in all areas of process technology and can be used with liquids and slurries. With a tuning fork insertion length of only 0 mm (.57 inch), can be mounted in small pipes and applications with confined space. The LVL00 can be used to measure products with a minimum density of > 0.5 g/cm³ (0.08 lb/in³). The LVL00 can be used in difficult conditions including turbulence, air bubbles, foam generation, buildup, or external vibration. continuously monitors faults via frequency evaluation, providing early detection of strong corrosion or damage on the tuning fork, loss of vibration, or a line break to the piezo drive. The tuning fork is piezoelectrically energized and vibrates at its mechanical resonance frequency of approximately 00 Hz. The vibration frequency changes when the tuning fork is covered by the medium. This change is detected by the integrated oscillator and converted into a switching command. The integrated electronics evaluate the level signal and output a switching signal, directly operating connected devices. The optional signal conditioner provides a remote test feature to ensure continuous product reliability. Key Applications: for use in liquids and slurries, for level measurement, overfill, and dry run protection Moisture protection NOTE: Welded socket for flush mount optional installation, dimensions in mm (inch) Ensure cable gland faces downward to avoid water ingress. Siemens FI 0 Update /07 /7

2 Technical specifications Mode of operation Measuring principle Input Measured variable Output Output options Vibrating point level switch High and low and demand (via mode switch) Relay output (DPDT), floating SPDTs Contactless electronic switch -wire Namur signal output Transistor (NPN/PNP) V DC 8/6 ma Measuring accuracy Repeatability 0. mm (0.00 inch) Hysteresis Approx. mm (0.08 inch) with vertical installation Switching delay Approx. 500 ms (on/off) Frequency Approx. 00 Hz Rated operating conditions Installation conditions Location Indoor/outdoor Ambient conditions Ambient temperature C ( F) Installation category III Pollution degree Medium conditions Temperature - LVL00S Standard C ( F) - LVL00S High temperature option C ( F) - LVL00E Standard: with C ( F) 36L/Hastelloy - LVL00E High temperature option: C ( F) with 36L/Hastelloy Pressure (vessel) bar g ( psi g) Density g/cm³ ( lb/in³); g/cm³ ( lb/in³) by switching over Design Material Enclosure Aluminum die-cast AISi0Mg, powder-coated, basis: Polyester Stainless steel housing, electropolished 36L 36L (.0 or.35), Hastelloy 36L (.0 or.35), Hastelloy Tuning fork Extension tube [ø.3 mm (0.839 inch)] Process connection: threaded 36L (.0 or.35), Hastelloy Process connection: flange 36L (.0 or.35), 36L with Hastelloy, ECTFE, or PFA coating Process seal Klingersil C-00 Process connection Pipe thread, cylindrical (ISO 8 T) G ¾" A, G " A Pipe thread, tapered ¾" NPT, " NPT, ½" NPT Flanges DIN from DN5, ASME from " Hygienic fittings Bolting DN 0 PN 0,, ½,, ½" Tri-Clamp PN 0, conus DN 5 PN 0, Tuchenhagen Varivent DN 50 PN 0, SMS Degree of protection Conduit entry Weight Device weight (dependent on process fitting) Tube extension (extended version) Power supply Supply voltage Relay DPDT Contactless -wire NAMUR Operating voltage (characteristics according to standard) for connection to an amplifier according to NAMUR Type X/NEMA X/IP66/IP67 x M0 x.5 (cable: ø mm), x blind stopper M0 x.5; attached x M0 x.5 cable entry x ½" NPT cable entry, x blind stopper ½" NPT, x ½" NPT cable entry x M x ; x blind stopper M0 x.5 Approx kg ( lb) Approx. 90 g/m (0 oz/ft) V AC, 50/60 Hz, V DC [at U > 60 V DC] V AC, 50/60 Hz, V DC IEC , approx. 8. V Off-load voltage U o approx. 8. V Short-circuit current I U approx. 8. ma Power consumption... 8 VA (AC), approx..3 W (DC) Relay DPDT... 8 VA (AC), approx..3 W (DC) Contactless Domestic current requirement approx. 3 ma (via load circuit) Load current Min. 0 ma Max. 00 ma [with I > 300 ma the ambient temperature can be max. 60 C (0 F)] Max. A up to 0 ms (not WHG specified) 8/6 ma, two-wire output Output signal Empty (uncovered) -8 ma Full (covered) -6 ma Fault message - <.8 ma Possible signal conditioning instruments: SITRANS SCSC, SITRANS TCSC -wire Namur Current consumption Falling characteristics.6 ma uncovered/ 0.6 ma covered 0.6 ma uncovered/.6 ma covered Failure message 0.6 ma Transistor (NPN/PNP) V DC Output Floating transistor output, permanently shortcircuit-proof Load current < 00 ma Voltage loss < V Switching voltage <55VDC Blocking current <0 A /7 Siemens FI 0 Update /07

3 Certificates and approvals CE, CSA Overfill Protection WHG and VLAREM II FM (Non-Incendive) Class I, Div., Groups A, B, C, D FM (Explosion-Proof) Class I, Div., Groups A, B, C, D; (Dust Ignition- Proof) Class II, III, Div., Groups E, F, G IECEx d IIC T6... T Ga/Gb EHEDG ATEX II /G, G EEx d IIC T6 ATEX II G, /G, G EEx ia IIC T6 Shipping approvals BR-Ex d IIC T6... T FDA, 3A, Ehedge SIL/IEC6508 Declaration of Conformity [SIL- (min/max detection)] Please see configuration section below for full list of approvals., Standard 7ML576- in liquid and slurry applications such as over A 0 flow, high, low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Click on the for the online configuration in the PIA Life Cycle Portal. Electronics Contactless electronic switch V AC/DC )9)) Double relay (DPDT) V DC/ V AC ) NAMUR signal 9) Transistor (NPN/PNP) V DC )5) 5 Two-wire (8/6 ma) V DC 6 Approvals Without approvals A Overfill protection (WHG) 9) B ATEX II G, /G, G Ex ia IIC T6 + WHG 6)9) C ATEX II /G, G Ex d IIC T6 + WHG 5)5) D ATEX II G, /G, G Ex ia IIC T6 + shipping E approvals 6)6) ATEX II /G, G Ex d IIC T6 + shipping F approvals 5)5) ATEX II G, /G, G Ex ia IIC T6 + ATEX II / D G IP6X T 6)7)7) IECEx Ex ia IIC T6 6)8) H Shipping approvals 6) K ATEX II 3G Ex na II T5...T X )9) L FM (IS) Class I, II, III, Div., Groups A, B, C, D, E, F, N G 6)0) FM (XP) Class I, Div., Groups A, B, C, D; (DIP) P Class II, III, Div., Groups E, F, G )5)0) FM (NI) Class I, Div., Groups A, B, C, D ) Q IECEx d IIC T6... T Ga/Gb 5)5) R CSA (XP) Class I, II, III Div., S Groups A,B, C, D, E, F, G 5)5) CSA(NI)Class I, II, III, Div., T Groups A, B, C, D, E, F, G ) BR-Ex d IIC T6... T 5)3) U CSA (IS) Class I, II, III Div., V Groups A, B, C, D, E, F, G 6)9) ATEX II G, /G, G Ex ia IIC T6 6) W Process connection Thread G¾" A, PN 6/36L A 0 0 Thread G¾" A, PN 6/36L Ra < 0.8 µm A 0 Thread ¾" NPT, PN 6/36L A 0 Thread ¾" NPT, PN 6/36L Ra < 0.8 µm A 0 3 Thread ¾" NPT, PN 6/Alloy 00 (.360) A 0 Thread G¾" A, PN 6/Alloy C (.60) A 0 5 Thread ¾" NPT, PN 6/Alloy C (.60) A 0 6 Thread G" A, PN 6/36L A 0 7 Thread G" A, PN 6/36L ECTFE coated MB98 ) A 0 8 Thread G" A, PN 6/ 36L PFA coated ) A 0 Thread G" A, PN 6/ Alloy 00 (.360) A Thread G" A, PN 6/ 36L Ra < 0.8 µm A Thread " NPT, PN 6/ 36L A 3 Thread " NPT, PN 6/ 36L ECTFE coated MB98 ) A Thread " NPT, PN 6 / 36L PFA-coated ) A 5 Thread " NPT, PN 6 / Alloy 00 (.360) A 6 Thread " NPT, PN 6 / 36L Ra < 0.8 µm A 7 Thread G" A, PN 6 / Alloy C (.60) A 8 Thread G" A, PN 6/Alloy C (.60) A 0 Ra < 0.3 µm Thread G½" A, PN 6/36L A Thread G½" A, PN 6/36L Ra < 0.8 µm A Thread G½" A, PN 6/Alloy C (.60) A 3 Siemens FI 0 Update /07 /73

4 , Standard 7ML576- in liquid and slurry applications such as overflow, A 0 high, low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Thread " NPT, PN 6/Alloy C (.60) A Thread ½" NPT, PN 6/36L A 5 Thread ½" NPT, PN 6/36L Ra < 0.8 µm A 6 Thread ½" NPT, PN 6/Alloy C (.60) A 7 Thread G" A, PN 6/36L A 8 Thread M7 x.5, PN 6/36L A 3 0 Conus DN 5, PN 0/36L Ra < 0.3 µm A 3 Conus DN 5, PN 0/36L Ra < 0.8 µm A 3 Conus DN 5, PN 0/ECTFE (ZB3033) ) A 3 3 Conus M5, PN 0/36L A 3 Conus M5, PN 0/36L Ra < 0.3 µm A 3 5 Conus M5, PN 0/36L Ra < 0.8 µm A 3 6 Tri-Clamp ", PN 6/36L Ra < 0.3 µm A 3 7 Tri-Clamp ", PN 6/Alloy C (.60) A 3 8 Tri-Clamp ", PN 6/36L Ra < 0.8 µm A 0 Tri-Clamp ½", PN 6/36L Ra < 0.3 µm A Tri-Clamp ½", PN 6/Alloy C (.60) A Tri-Clamp ½", PN 6/36L Ra < 0.8 µm A 3 Tri-Clamp ", PN 6/36L Ra < 0.3 µm A Tri-Clamp ", PN 6/Alloy C (.60) A 5 Tri-Clamp ", PN 6/36L Ra < 0.8 µm A 6 Tri-Clamp ½", PN 0/36L Ra < 0.3 µm A 7 Tri-Clamp ½", PN 0/36L Ra < 0.8 µm A 8 Tri-Clamp 3", PN 0/36L Ra < 0.3 µm A 5 0 Tri-Clamp 3", PN 0/36L Ra < 0.8 µm A 5 Bolting DN 3, PN 0 DIN85/36L Ra < 0.3 µm A 5 Bolting DN 3, PN 0 DIN85/36L Ra < 0.8 µm A 5 3 Bolting DN 5, PN 0 DIN85/36L Ra < 0.3 µm A 5 Bolting DN 5, PN 0 DIN85/36L Ra < 0.8 µm A 5 5 Bolting DN 0, PN 0 DIN85/36L Ra < 0.3 µm A 5 6 Bolting DN 0, PN 0 DIN85/36L Ra < 0.8 µm A 5 7 Bolting DN 0, PN 0 DIN86- A/36L A 5 8 Ra < 0.8 µm ZB305 Bolting DN 50, PN 5 DIN85/36L Ra < 0.3 µm A 6 0 Bolting DN 50, PN 5 DIN85/36L Ra < 0.8 µm A 6 Bolting DN 50, PN 5 DIN86- A/36L A 6 Ra < 0.8 µm ZB305 Hygienic w. compr. nut F0, PN 5/36L A 6 3 Hygienic w. compr. nut F0, PN 5/36L A 6 Ra < 0.3 µm Hygienic w. compr. nut F0, PN 5/36L A 6 5 Ra < 0.8 µm Varivent N50-0/36L Ra < 0.3 µm A 6 6 Varivent N50-0/36L Ra < 0.8 µm A 6 7 Varivent N5/00/36L Ra < 0.8 µm A 6 8 DRD flange, PN 0/36L ZB3007 A 7 0 SMS DN 38/36L Ra < 0.8 µm ) A 7 SMS DN 5, PN 6/36L Ra < 0.8 µm ) A 7 Swagelok VCR screwing ZG579, PN 6/36L A 7 3 Neumo biocontrol size 5, PN 6/36L Ra < 0.8 µm A 7 Neumo biocontrol size 50, PN 6/36L Ra < 0.8 µm ) A 7 5 Neumo biocontrol size 65, PN 6/36L Ra < 0.8 µm A 7 6 Neumo biocontrol size 80, PN 6/36L Ra < 0.8 µm A 7 7 SÜDMO DN 50, PN 0/36L Ra < 0.8 µm A 7 8 Small flange DN 5, PN.5 DIN 803/36L pol. A 8 0 Ra < 0.8 µm Small flange DN 0, PN.5 DIN 803/36L pol. A 8 Ra < 0.8 µm Ingold connection, PN6 / 36 A 8 L Ra < 0.8 µm (acc. to MB53), Standard 7ML576- in liquid and slurry applications such as overflow, A 0 high, low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Ingold connection, PN 6/Alloy C (.60) A 8 3 Ra < 0.8 µm (acc. to MB607) Terminal DN 33.7 PN 0 DIN86-3-A-/36L BN Ra < 0.8 µm ) A 8 Hygienic fl. DN 50 PN 6 DIN86--A-/36L A 8 5 Ra < 0.8 µm Flange DN 5, PN 6 Form C, DIN 50/36L A 8 6 Flange DN 5, PN 6 Form C, DIN 50/PFA ) A 8 7 Flange DN 5, PN 0 Form C, DIN 50/36L A 8 8 Flange DN 5, PN 0 Form C, DIN 50/ B 0 0 Alloy C (.60) Flange DN 5, PN 0 Form C, DIN 50/ECTFE ) B 0 Flange DN 5, PN 0 Form C, DIN 50/PFA ) B 0 Flange DN 5, PN 0 Form C, DIN 50/Enamelled B 0 3 Flange DN 5, PN 0 Form D, DIN 50/36L B 0 Flange DN 5, PN 0 Form F, DIN 50/36L B 0 5 Flange DN 5, PN 0 Form N, DIN 50/36L B 0 6 Flange DN 5, PN 0 Form N, DIN 50/ B 0 7 Alloy C (.60) Flange DN 5, PN 0 Form N, DIN 50/ B 0 8 Alloy 00 (.360) solid Flange DN 5, PN 0 V3, DIN 50/36L B 0 Flange DN 3, PN 0 Form C, DIN 50/36L B Flange DN 3, PN 0 Form C, DIN 50/ECTFE ) B Flange DN 0, PN 6 Form C, DIN 50/36L B 3 Flange DN 0, PN 6 Form C, DIN 50/ECTFE ) B Flange DN 0, PN 0 Form C, DIN 50/36L B 5 Flange DN 0, PN 0 Form C, DIN 50/ B 6 Alloy C (.60) Flange DN 0, PN 0 Form C, DIN 50/ECTFE ) B 7 Flange DN 0, PN 0 Form C, DIN 50/PFA ) B 8 Flange DN 0, PN 0 Form C, DIN 50/ Enamelled 3) B 0 Flange DN 0, PN 0 Form F, DIN 50/36L B Flange DN 0, PN 0 Form N, DIN 50/36L B Flange DN 0, PN 0 Form E, DIN 50/36L B 3 Flange DN 0, PN 0 V3, DIN 50/36L B Flange DN 50, PN 0 Form C, DIN 50/36L B 5 Flange DN 50, PN 0 Form C, DIN 50/ B 6 Alloy C (.60) Flange DN 50, PN 0 Form C, DIN 50/ECTFE ) B 7 Flange DN 50, PN 0 Form C, DIN 50/ ECTFE (ZB308) ) B 8 Flange DN 50, PN 0 Form C, DIN 50/PFA ) B 3 0 Flange DN 50, PN 0 Form D, DIN 50/36L B 3 Flange DN 50, PN 0 Form D, DIN 50/ B 3 Alloy C (.60) Flange DN 50, PN 0 Form F, DIN 50/36L B 3 3 Flange DN 50, PN 0 Form N, DIN 50/36L B 3 Flange DN 50, PN 0 Form N, DIN 50/ B 3 5 Alloy C (.60) Flange DN 50, PN 0 Form E, DIN 50/36L B 3 6 Flange DN 50, PN 0 V3, DIN 50/36L B 3 7 Flange DN 50, PN 0 R3, DIN 50/36L B 3 8 Flange DN 50, PN 6 Form F, DIN 50/36L B 0 Flange DN 50, PN 6 Form N, DIN 50/ B Alloy C (.60) Flange DN 50, PN 6 Form C, DIN 50/36L B Flange DN 50, PN 6 Form L, DIN 50/36L B 3 Flange DN 50, PN 00 Form E, DIN 50/36L B Flange DN 50, PN 00 Form L, DIN 50/36L B 5 Flange DN 65, PN 0 Form C, DIN 50/36L B 6 /7 Siemens FI 0 Update /07

5 , Standard in liquid and slurry applications such as overflow, high, low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. 7ML A 0 Flange DN 65, PN 0 Form C, DIN 50/ B 7 Alloy C (.60) Flange DN 65, PN 0 Form C, DIN 50/ECTFE ) B 8 Flange DN 65, PN 0 Form C, DIN 50/PFA ) B 5 0 Flange DN 65, PN 0 Form F, DIN 50/36L B 5 Flange DN 65, PN 6 Form E, DIN 50/36L B 5 Flange DN 80, PN 0 Form C, DIN 50/36L B 5 3 Flange DN 80, PN 0 Form C, DIN 50/ B 5 Alloy C (.60) Flange DN 80, PN 0 Form C, DIN 50/ECTFE ) B 5 5 Flange DN 80, PN 0 Form C, DIN 50/PFA ) B 5 6 Flange DN 80, PN 0 Form C, DIN 50/ Enamelled 3) B 5 7 Flange DN 80, PN 0 Form F, DIN 50/36L B 5 8 Flange DN 80, PN 0 Form N, DIN 50/36L B 6 0 Flange DN 00, PN 6 Form C, DIN 50/36L B 6 Flange DN 00, PN 6 Form C, DIN 50/ B 6 3 Alloy C (.60) Flange DN 00, PN 6 Form C, DIN 50/ECTFE ) B 6 Flange DN 00, PN 6 Form C, DIN 50/PFA ) B 6 5 Flange DN 00, PN 6 Form C, DIN 50/ Enamelled 3) B 6 6 Flange DN 00, PN 6 Form D, DIN 50/36L B 6 7 Flange DN 00, PN 6 Form F, DIN 50/36L B 6 8 Flange DN 00, PN 6 Form N, DIN 50/36L B 7 0 Flange DN 00, PN 0 Form C, DIN 50/36L B 7 Flange DN 00, PN 0 Form C, DIN 50/ECTFE ) B 7 Flange DN 00, PN 0 Form C, DIN 50/PFA ) B 7 3 Flange DN 00, PN 0 Form C, DIN 50/ Enamelled 3) B 7 Flange DN 00, PN 0 Form F, DIN 50/36L B 7 5 Flange DN 00, PN 0 Form N, DIN 50/36L B 7 6 Flange DN 00, PN 0 V3, DIN 50/36L B 7 7 Flange DN 00, PN 6 Form E, DIN 50/36L B 7 8 Flange DN 00, PN 00 Form E, DIN 50/36L B 8 0 Flange DN 00, PN 00 Form L, DIN 50/36L B 8 Flange DN 5, PN 6 Form F, DIN 50/36L B 8 Flange DN 5, PN 0 Form C, DIN 50/36L B 8 3 Flange DN 5, PN 0 Form N, DIN 5/ 36L B 8 Flange DN 50, PN 6 Form C, DIN 50/36L B 8 5 Flange DN 50, PN 6 Form C, DIN 50/ B 8 6 Alloy C (.60) Flange DN 50, PN 6 Form C, DIN 50/ECTFE ) B 8 7 Flange DN 50, PN 6 Form C, DIN 50/PFA ) B 8 8 Flange DN 50, PN 6 Form D, DIN 50/36L C 0 0 Flange DN 50, PN 0 Form C, DIN 50/36L C 0 Flange DN 50, PN 0 Form C, DIN 50/ C 0 Alloy C (.60) Flange DN 50, PN 0 Form F, DIN 50/36L C 0 3 Flange DN 50, PN 0 Form N, DIN 5/36L C 0 Flange DN 00, PN 0 Form C, DIN 50/ECTFE ) C 0 5 Flange DN 00, PN 6 Form C, DIN 50/36L C 0 6 Flange DN 5, PN 0 Form B, EN 09-/36L C 0 7 Flange DN 5, PN 0 Form B, EN 09-/ C 0 8 Alloy C (.60) Flange DN 5, PN 0 Form B, EN/ 36L/ PFA ) C 0 Flange DN 5, PN 0 Form B, EN 09-/ Enamelled 3) C Flange DN 5, PN 0 Form B, EN 09-/36L C Flange DN 5, PN 0 Form F, EN 09-/36L C 3 Flange DN 5, PN 63 Form B, EN 09-/36L C, Standard 7ML576- in liquid and slurry applications such as overflow, A 0 high, low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Flange DN 5, PN 00 Form B, EN 09-/36L C 5 Flange DN 0, PN 0 Form B, EN/ 36L C 6 Flange DN 0, PN 0 Form B, EN 09-/PFA ) C 7 Flange DN 0, PN 0 Form B, EN/36L C 8 Flange DN 50, PN 0 Form B, EN/36L C 0 Flange DN 50, PN 0 Form B, EN 09-/ C Alloy C (.60) Flange DN 50, PN 0 Form B, EN 09-/ C Alloy 00 (.360) ZB977 Flange DN 50, PN 0 Form B, EN 09-/ECTFE ) C 3 Flange DN 50, PN 0 Form B, EN/ 36L/PFA ) C Flange DN 50, PN 0 Form B, EN 09-/ Enamelled 3) C 5 Flange DN 50, PN 0 Form C, EN 09-/36L C 6 Flange DN 50, PN 0 Form D, EN/36L C 7 Flange DN 50, PN 0 Form D, EN 09-/ C 8 Alloy C (.60) Flange DN 50, PN 0 Form B, EN 09-/36L C 3 0 Flange DN 50, PN 0 Form E, EN 09-/36L C 3 Flange DN 80, PN 0 Form B, EN 09-/36L C 3 Flange DN 80, PN 0 Form B, EN 09-/ C 3 3 Alloy C (.60) Flange DN 80, PN 0 Form B, EN 09-/ECTFE ) C 3 Flange DN 80, PN 0 Form B, EN 09-/ Enamelled 3) C 3 5 Flange DN 80, PN 0 Form B, EN 09-/36L C 3 6 Flange DN 00, PN 6 Form B, EN 09-/36L C 3 7 Flange DN 00, PN 6 Form B, EN 09-/ C 3 8 Alloy C (.60) Flange DN 00, PN 6 Form B, EN 09-/ Enamelled 3) C 0 Flange DN 00, PN 0 Form B, EN 09-/36L C Flange DN 00, PN 0 Form B, EN 09-/ Enamelled 3) C Flange DN 00, PN 0 Form C, EN 09-/36L C 3 Flange DN 00, PN 63 Form B, EN 09-/36L C Flange DN 50, PN 6 Form B, EN 09-/36L C 5 Flange DN 50, PN 6 Form B, EN 09-/PFA ) C 6 Flange DN 50, PN 0 Form B, EN 09-/36L C 7 Flange DN 50, PN 0 Form B, EN 09-/ECT- FE ) C 8 Flange DN 50, PN 0 Form B, EN 09-/36L C 5 0 Flange " 50 lb ASME B6.5/36L C 5 Flange " 50 lb RF, ASME B6.5/Alloy C C 5 (.60) Flange " 50 lb RF, ASME B6.5/Alloy 00 (.360) C 5 3 ZB977 Flange " 50 lb RF, ASME B6.5/ECTFE ) C 5 Flange " 50 lb RF, ASME B6.5/PFA ) C 5 5 Flange " 50 lb RF, ASME B6.5/Enamelled 3) C 5 6 Flange " 300 lb RF, ASME B6.5/36L C 5 7 Flange " 300 lb RF, ASME B6.5/ECTFE ) C 5 8 Flange " 600 lb RF, ASME B6.5/36L C 6 0 Flange ½" 50 lb RF, ASME B6.5/36L C 6 Flange ½" 50 lb RF, ASME B6.5/ C 6 Alloy C (.60) Flange ½" 50 lb RF, ASME B6.5/ECTFE ) C 6 3 Flange ½" 50 lb RF, ASME B6.5/PFA ) C 6 Flange ½" 50 lb RF, ASME B6.5 Enamelled 3) C 6 5 Flange ½" 50 lb FF, ASME B6.5/ECTFE ) C 6 6 Flange ½" 300 lb RF, ASME B6.5/36L C 6 7 Siemens FI 0 Update /07 /75

6 , Standard in liquid and slurry applications such as overflow, 7ML A 0 high, low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Flange ½" 300 lb RF, ASME B6.5/ C 6 8 Alloy 00 (.360) ZB977 Flange ½" 300 lb RF, ASME B6.5/ECTFE 3) C 7 0 Flange ½" 600 lb RF, ASME B6.5/36L C 7 Flange " 50 lb RF, ASME B6.5/36L C 7 Flange " 50 lb RF, ASME B6.5/Alloy C C 7 3 (.60) Flange " 50 lb RF, ASME B6.5/Alloy 00 (.360) C 7 ZB977 Flange " 50 lb RF, ASME B6.5/ECTFE ) C 7 5 Flange " 50 lb RF, ASME B6.5/PFA ) C 7 6 Flange " 50 lb RF, ASME B6.5/Enamelled 3) C 7 7 Flange " 50 lb FF, ASME B6.5/36L C 7 8 Flange " 50 lb FF, ASME B6.5/ECTF ) C 8 0 Flange " 50 lb SG (small groove), C 8 ASME B6.5/36L Flange " 300 lb RF, ASME B6.5/36L C 8 Flange " 300 lb RF, ASME B6.5/Alloy C C 8 3 (.60) Flange " 300 lb RF, ASME B6.5/ECTFE ) C 8 5 Flange " 300 lb RF, ASME B6.5/PFA ) C 8 6 Flange " 300 lb RF, ASME B6.5 Enamelled 3) C 8 7 Flange " 300 lb RJF, ASME B6.5/36L C 8 8 Flange " 300 lb ST, ASME B6.5/36L D 0 0 Flange " 300 lb LG (large groove), D 0 ASME B6.5/36L Flange " 300 lb LT, ASME B6.5/36L D 0 Flange " 600 lb RF, ASME B6.5/36L D 0 3 Flange " 600 lb RF, ASME B6.5/Alloy 00 (.360) D 0 ZB977 Flange " 600 lb RF, ASME B6.5/ECTFE ) D 0 5 Flange " 600 lb RJF, ASME B6.5/36L D 0 6 Flange " 600 lb LG, ASME B6.5/36L D 0 7 Flange " 900 lb RJF, ASME B6.5/36L D 0 8 Flange ½" 50 lb RF, ASME B6.5/36L D 0 Flange ½" 300 lb RF, ASME B6.5/36L D Flange 3" 50 lb RF, ASME B6.5/36L D Flange 3" 50 lb RF, ASME B6.5/Alloy C D 3 (.60) Flange 3" 50 lb RF, ASME B6.5/ECTFE ) D Flange 3" 50 lb RF, ASME B6.5/PFA ) D 5 Flange 3" 50 lb RF, ASME B6.5/Enamelled 3) D 6 Flange 3" 50 lb FF, ASME B6.5/36L D 7 Flange 3" 50 lb FF, ASME B6.5/ECTFE ) D 8 Flange 3" 50 lb FF, ASME B6.5/PFA ) D 0 Flange 3" 300 lb RF, ASME B6.5/36L D Flange 3" 300 lb RF, ASME B6.5/Alloy C D (.60) Flange 3" 300 lb RF, ASME B6.5/ECTFE ) D 3 Flange 3" 300 lb RF, ASME B6.5/PFA ) D Flange 3" 300 lb RF, ASME B6.5/Enamelled 3) D 5 Flange 3" 600 lb RF, ASME B6.5/36L D 6 Flange 3½" 50 lb RF, ASME B6.5/36L D 7 Flange 3½" 50 lb RF, ASME B6.5/ECTFE ) D 8 Flange " 50 lb RF, ASME B6.5/36L D 3 0 Flange " 50 lb RF, ASME B6.5/Alloy C D 3 (.60) Flange " 50 lb RF, ASME B6.5/ECTFE ) D 3 Flange " 50 lb RF, ASME B6.5/PFA ) D 3 3 Flange " 50 lb RF, ASME B6.5/Enamelled 3) D 3, Standard in liquid and slurry applications such as overflow, 7ML A 0 high, low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Flange " 50 lb LT, ASME B6.5/36L D 3 5 Flange " 300 lb RF, ASME B6.5/36L D 3 6 Flange " 300 lb RF, ASME B6.5/Alloy C D 3 7 (.60) Flange " 300 lb RF, ASME B6.5/ECTFE ) D 3 8 Flange " 300 lb RJF, ASME B6.5/36L D 0 Flange " 300 lb LG, ASME B6.5/36L D Flange " 300 lb LT, ASME B6.5/36L D Flange " 600 lb RF, ASME B6.5/36L D 3 Flange " 600 lb RJF, ASME B6.5/36L D Flange 6" 50 lb RF, ASME B6.5/36L D 5 Flange 6" 50 lb RF, ASME B6.5/Alloy C D 6 (.60) Flange 6" 50 lb RF, ASME B6.5/ECTFE ) D 7 Flange 6" 50 lb RF, ASME B6.5/PFA ) D 8 Flange 6" 50 lb RJF, ASME B6.5/36L D 5 0 Flange 6" 300 lb RF, ASME B6.5/36L D 5 Flange 8" 50 lb RF, ASME B6.5/36L D 5 Flange 8" 50 lb RF, ASME B6.5/ECTFE ) D 5 3 Flange " BS.0 Table E/36L D 5 Flange " BS.0 Table E/PFA ) D 5 5 Flange ½" BS.0 Table E/36L D 5 6 Flange 3½" BS.0 Table E/36L D 5 7 Flange " BS.0 Table E/ECTFE ) D 5 8 Flange DN 0 0K, JIS/36L D 6 0 Flange DN 50 0K, JIS/36L D 6 Flange DN 80 0K, JIS/36L D 6 Flange DN 00 0K, JIS/36L D 6 3 Thread R PN 6, EN 06-/36L D 6 5 Flange " 900 lb RF, ASME B6.5/36L D 7 0 Adapter/Process temperature Without adapter/ C ( F) With adapter/ C ( F) 3) With adapter/ C ( F) 3 With gas-tight leadthrough/ C ( F) With gas-tight leadthrough/ C 5 ( F) Housing/Cable entry Aluminum IP66/IP67/M0 x.5 A Aluminum IP66/IP67/½" NPT B 36L stainless steel (electropolished) C IP66/IP67/M0 x.5 36L stainless steel (electropolished) D IP66/IP67/½" NPT Plastic single chamber IP66/IP67/M0 x.5 E Plastic single chamber IP66/IP67/½" NPT F Stainless steel chamber (precision casting) G IP66/IP67/M0 x.5 Stainless steel chamber (precision casting) H IP66/IP67/½" NPT Aluminum IP66/IP67/M0 x.5 Special HARTING V plug (bent) according to Tier One (ZB7555) ) /76 Siemens FI 0 Update /07

7 Further designs Order code.-factory certificate for material (EN 00) 8) Order code C5 Please add "-Z" to and specify Order code(s). Switching status indication with colors red-green ) Cleaning including Certificate (oil, grease, and silicone free) A W0 Functional Safety (SIL ). Device suitable for use in C0 accordance with IEC 6508 and IEC 65 8) Dye penetration test, results confirmed via a C3 3. certificate/instrument (EN00) 8) X-ray test + 3. certificate/instrument 8) C Identification label (measurement loop) stainless steel: max. 0 characters, add in plain text. To add more than one line, use a coma ","" for line break. Identification Label (measurement loop) foil: max. 0 characters add in plain text. To add more than one line, use a coma "," for line break. NACE075 to 3. Material Certificate for material (EN00 NACE MR 075) 8) Note: not available with Process Connection and Rigid extension coatings PFA, ECTFE, and Enamel. NACE not available with Hygienic process connections. Y7 Y8 D07 Positive material identification test + 3. certificate/instrument 8) C6 Roughness test + 3. certificate/instrument 8) C8 3.-Inspection Certificate for instrument with test C5 data (EN 00) Quality and test plan C6 Pressure test + 3. certificate/instrument 8) C3 Helium leak test + 3. certificate/instrument 8) C3 Ferrite measuring accuracy to DIN certificate/instrument 8) C60 Pressure test according to Norsok + 3. certificate/instrument 8) C6 Operating Instructions All literature is available to download for free, in a range of languages, at processinstrumentation/documentation Spare Parts and Accessories Electronics module Relay 7ML830-NC Electronics module Contactless 7ML930-6AA NAMUR spare electronics module A5E LVL00 Threaded Welded Socket G¾" A/36L with FKM Seal 7ML930-EE G" A/36L with FKM Seal 7ML930-EF M7 x.5/36l with FKM Seal 7ML930-EG G¾" A/36L with EPDM Seal 7ML930-EH G" A/36L with EPDM Seal 7ML930-EJ M7 x.5/36l with EPDM Seal 7ML930-EK ) Available only with Adapter/Process temperature options, 3,, and 5. ) Available only with Housing/Protection/Cable option B. 3) Available only with Adapter/Process Temperature options,, and. ) Not available with Adapter/Process Temperature options, 3, and 5. 5) Not available with Adapter/Process Temperature options,, and 5. 6) Available only with Electronics options and 6. 7) Not available with ECTFE coated probe options. 8) Listed Certificates are not available with all configurations please contact factory for more information. 9) Not available with Housing/Protection/Cable Option V. 0) Not available with PFA and ECTFE coating options. ) Available only with Approval option A. ) Available only with Relay Electronic options and Non-hazardous Approval options. 3) Available only with Enamelled Process connection options. ) Available only with Electronic options, 5, and 6. 5) Available only with Aluminum Housing/Protection/Cable options. 6) Not available with Stainless Steel (electropolished) Housing/Protection/Cable options and certain glands. 7) Not available with Plastic and Stainless Steel (electropolished) Housing/Protection/Cable options and certain glands. 8) Not available with Housing/Protection/Cable options D, and V. 9) Not available with Plastic Housing/Protection/Cable options and certain glands. 0) Not available with Housing/Protection/Cable options A, E, G, and V. ) Available only with Housing/Protection/Cable options B, D, F, and H. ) Not available with Housing/Protection/Cable options C and V. 3) Available only with Housing/Protection/Cable options A, B, and H. ) Not available with Approval options C, E, G, H, L, N, V, and W. 5) Not available with Approval options C, E, G, H, N, V, and W. Siemens FI 0 Update /07 /77

8 , Rigid extension in liquid applications such as overflow, high, 7ML low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Click on the for the online configuration in the PIA Life Cycle Portal. Electronics Contactless electronic switch V AC/DC )9)) Double relay (DPDT) V DC/ V AC ) NAMUR signal 9) Transistor (NPN/PNP) V DC )5) 5 Two-wire (8/6 ma) V DC 6 Approvals Without approvals A Overfill protection (WHG) 9) B ATEX II G, /G, G Ex ia IIC T6 + WHG 6)9) C ATEX II /G, G Ex d IIC T6 + WHG 5)7)6) D ATEX II G, /G, G Ex ia IIC T6 + shipping E approvals 6)7) ATEX II /G, G Ex d IIC T6 + shipping approvals F 5)7)6) ATEX II G, /G, G Ex ia IIC T6 + ATEX II /D G IP6X T 6)8)8) IECEx Ex ia IIC T6 6)9) H Shipping approvals 7) K ATEX II 3G Ex na II T5... T X 8) L FM (IS) Class I, II, III, Div., Groups A, B, C, D, E, F, G 6)0) N FM (XP) Class I, Div., Groups A, B, C, D; (DIP) P Class II, III, Div., Groups E, F, G )5) FM (NI) Class I, Div., Groups A, B, C, D ) Q IECEx d IIC T6... T Ga/Gb 5)7)6) R CSA(XP) Class I,II,III Div., S Groups A, B, C, D, E, F, G )5)7) CSA(NI)Class I,II,III, Div., T Groups A, B, C, D, E, F, G ) BR-Ex d IIC T6... T 5)8) U CSA (IS) Class I, II, III Div., V Gruppen A, B, C, D, E, F, G 6)9) ATEX II G, /G, G Ex ia IIC T6 6) W NOTE: When selecting a Process connection option, process connection coating must match the extension coating and the material and surface roughness type. Process connection Thread G¾" A, PN 6/36L A 0 0 Thread G¾" A, PN 6/36L Ra < 0.8 µm A 0 Thread ¾" NPT, PN 6/36L A 0 Thread ¾" NPT, PN 6/36L Ra < 0.8 µm A 0 3 Thread ¾" NPT, PN 6/Alloy 00 (.360) A 0 Thread G¾" A, PN 6/Alloy C (.60) A 0 5 Thread ¾" NPT, PN 6/Alloy C (.60) A 0 6 Thread G" A, PN 6/36L A 0 7 Thread G" A, PN 6/36L ECTFE coated MB98 ) A 0 8 Thread G" A, PN 6/36L PFA coated ) A 0 Thread G" A, PN 6/Alloy 00 (.360) A Thread G" A, PN 6/36L Ra < 0.8 µm A 3 Thread " NPT, PN 6/36L A Thread " NPT, PN 6/36L ECTFE coated MB98 ) A 5 Thread " NPT, PN 6/36L PFA coated ) A 6 Thread " NPT, PN 6/Alloy 00 (.360) A 7 Thread " NPT, PN 6/36L Ra < 0.8 µm A 8 Thread G" A, PN 6/Alloy C (.60) A 0, Rigid extension in liquid applications such as overflow, high, 7ML low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Thread G½" A, PN 6/36L A Thread G½" A, PN 6/36L Ra <0.8 µm A Thread G½" A, PN 6/Alloy C (.60) A 3 Thread " NPT, PN 6/Alloy C (.60) A Thread ½" NPT, PN 6/36L A 5 Thread ½" NPT, PN 6/36L Ra< 0.8 µm A 6 Thread ½" NPT, PN 6/Alloy C (.60) A 7 Thread G" A, PN 6/36L A 8 Thread M7 x.5 PN 6/36L A 3 0 Cyl. socket/36ti/.58 ECTFE coated ZB98 ) A 3 Conus DN 5 PN 0/36L Ra < 0.3 µm A 3 Conus DN 5 PN 0/36L Ra < 0.8 µm A 3 3 Conus DN 5 PN 0/ECTFE (ZB3033) ) A 3 Conus M5 PN 0/36L A 3 5 Conus M5 PN 0/36L Ra < 0.3 µm A 3 6 Conus M5 PN 0/36L Ra < 0.8 µm A 3 7 Tri-Clamp " PN 6/36L Ra < 0.3 µm A 3 8 Tri-Clamp " PN 6/Alloy C (.60) A 0 Tri-Clamp " PN 6/36L Ra < 0.8 µm A Tri-Clamp ½" PN 6/36L Ra < 0.3 µm A Tri-Clamp ½" PN 6/Alloy C (.60) A 3 Tri-Clamp ½" PN 6/36L Ra < 0.8 µm A Tri-Clamp " PN 6/36L Ra < 0.3 µm A 5 Tri-Clamp " PN 6/Alloy C (.60) A 6 Tri-Clamp " PN 6/36L Ra < 0.8 µm A 7 Tri-Clamp ½" PN 0/36L Ra < 0.3 µm A 8 Tri-Clamp ½" PN 0/36L Ra < 0.8 µm A 5 0 Tri-Clamp 3" PN 0/36L Ra < 0.3 µm A 5 Tri-Clamp 3" PN 0/36L Ra < 0.8 µm A 5 Bolting DN 3 PN 0 DIN85/36L Ra < 0.3 µm A 5 3 Bolting DN 3 PN 0 DIN85/36L Ra < 0.8 µm A 5 Bolting DN 5 PN 0 DIN85/36L Ra < 0.3 µm A 5 5 Bolting DN 5 PN 0 DIN85/36L Ra < 0.8 µm A 5 6 Bolting DN 0 PN 0 DIN85/36L Ra < 0.3 µm A 5 7 Bolting DN 0 PN 0 DIN85/36L Ra < 0.8 µm A 5 8 Bolting DN 0 PN 0 DIN86- A/36L A 6 0 Ra < 0.8 µm ZB305 Bolting DN 50 PN 5 DIN85/36L Ra < 0.3 µm A 6 Bolting DN 50 PN 5 DIN85/36L Ra < 0.8 µm A 6 Bolting DN 50 PN 5 DIN86- A/36L A 6 3 Ra < 0.8 µm ZB305 Hygienic w.compr.nut F0 PN 5/36L A 6 Hygienic w.compr.nut F0 PN 5/36L Ra < 0.3 µm A 6 5 Hygienic w.compr.nut F0 PN 5/36L Ra < 0.8 µm A 6 6 Varivent N50-0/36L Ra < 0.3 µm A 6 7 Varivent N50-0/36L Ra < 0.8 µm A 6 8 Varivent N5/00/36L Ra < 0.8 µm A 7 0 DRD flange PN 0/36L ZB3007 A 7 SMS DN 38/36L Ra < 0.8 µm ) A 7 SMS DN 5 PN 6/36L Ra < 0.8 µm ) A 7 3 Swagelok VCR screwing ZG579 PN 6/36L A 7 Neumo biocontrol size 5 PN 6/36L Ra < 0.8 µm A 7 5 Neumo biocontrol size 50 PN 6/36L Ra < 0.8 µm A 7 6 SÜDMO DN 50 PN 0/36L Ra < 0.8 µm A 8 0 Small flange DN 5 PN.5 DIN 803/36L pol. A 8 Ra<0.8 µm Small flange DN 0 PN.5 DIN 803/36L pol. A 8 Ra<0.8 µm Ingold connection PN 6/36L Ra < 0.8 µm A 8 3 /78 Siemens FI 0 Update /07

9 , Rigid extension in liquid applications such as overflow, high, low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. 7ML Collar clamp connection DN33,7 PN0 Form A, A 8 DIN86-3/.35 (BN, Ra < 0.8 µm) Collar flange DN50 PN6 Form A, DIN86-/ A L (Ra < 0.8 µm) Flange DN 5 PN 6 Form C, DIN 50/36L A 8 6 Flange DN 5 PN 6 Form C, DIN 50/PFA ) A 8 7 Flange DN 5 PN 0 Form C, DIN 50/36L A 8 8 Flange DN 5 PN 0 Form C, DIN 50/ B 0 0 Alloy C (.60) plated Flange DN 5 PN 0 Form C, DIN 50/ECTFE ) B 0 Flange DN 5 PN 0 Form C, DIN 50/PFA ) B 0 Flange DN 5 PN 0 Form D, DIN 50/36L B 0 3 Flange DN 5 PN 0 Form F, DIN 50/36L B 0 Flange DN 5 PN 0 Form N, DIN 50/36L B 0 5 Flange DN 5 PN 0 Form N, DIN 50/ B 0 6 Alloy C (.60) plated Flange DN 5 PN 0 Form N, DIN 50/ B 0 7 Alloy 00 (.360) solid Flange DN 5 PN 0 V3, DIN 50/36L B 0 8 Flange DN 3 PN 0 Form C, DIN 50/36L B 0 Flange DN 3 PN 0 Form C, DIN 50/ECTFE ) B Flange DN 0 PN 6 Form C, DIN 50/36L B Flange DN 0 PN 6 Form C, DIN 50/ECTFE ) B 3 Flange DN 0 PN 0 Form C, DIN 50/36L B Flange DN 0 PN 0 Form C, DIN 50/ B 5 Alloy C (.60) plated Flange DN 0 PN 0 Form C, DIN 50/ECTFE ) B 6 Flange DN 0 PN 0 Form C, DIN 50/PFA ) B 7 Flange DN 0 PN 0 Form C, DIN 50/Enamelled 3) B 8 Flange DN 0 PN 0 Form F, DIN 50/36L B 0 Flange DN 0 PN 0 Form N, DIN 50/36L B Flange DN 0 PN 0 Form E, DIN 50/36L B Flange DN 0 PN 0 V3, DIN 50/36L B 3 Flange DN 50 PN 0 Form C, DIN 50/36L B Flange DN 50 PN 0 Form C, DIN 50/ B 5 Alloy C (.60) plated Flange DN 50 PN 0 Form C, DIN 50/ECTFE ) B 6 Flange DN 50 PN 0 Form C, DIN 50/ECTFE (ZB308) ) B 7 Flange DN 50 PN 0 Form C, DIN 50/PFA ) B 8 Flange DN 50 PN 0 Form D, DIN 50/36L B 3 0 Flange DN 50 PN 0 Form D, DIN 50/ B 3 Alloy C (.60) Flange DN 50 PN 0 Form F, DIN 50/36L B 3 Flange DN 50 PN 0 Form N, DIN 50/36L B 3 3 Flange DN 50 PN 0 Form N, DIN 50/ B 3 Alloy C (.60) solid Flange DN 50 PN 0 Form E, DIN 50/36L B 3 5 Flange DN 50 PN 0 V3, DIN 50/36L B 3 6 Flange DN 50 PN 0 R3, DIN 50/36L B 3 7 Flange DN 50 PN 6 Form F, DIN 50/36L B 3 8 Flange DN 50 PN 6 Form N, DIN 50/ B 0 Alloy C (.60) plated Flange DN 50 PN 6 Form C, DIN 50/36L B Flange DN 50 PN 6 Form L, DIN 50/36L B Flange DN 50 PN 00 Form E, DIN 50/36L B 3 Flange DN 50 PN 00 Form L, DIN 50/36L B Flange DN 65 PN 0 Form C, DIN 50/36L B 5 Flange DN 65 PN 0 Form C, DIN 50/ B 6 Alloy C (.60) plated, Rigid extension in liquid applications such as overflow, high, 7ML low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Flange DN 65 PN 0 Form C, DIN 50/ECTFE ) B 7 Flange DN 65 PN 0 Form C, DIN 50/PFA ) B 8 Flange DN 65 PN 0 Form F, DIN 50/36L B 5 0 Flange DN 65 PN 6 Form E, DIN 50/36L B 5 Flange DN 80 PN 0 Form C, DIN 50/36L B 5 Flange DN 80 PN 0 Form C, DIN 50/ B 5 3 Alloy C (.60) plated Flange DN 80 PN 0 Form C, DIN 50/ECTFE ) B 5 Flange DN 80 PN 0 Form C, DIN 50/PFA ) B 5 5 Flange DN 80 PN 0 Form F, DIN 50/36L B 5 6 Flange DN 80 PN 0 Form N, DIN 50/36L B 5 7 Flange DN 80 PN 0 Form N, DIN 50/ B 5 8 Alloy C (.60) plated Flange DN 00 PN 6 Form C, DIN 50/36L B 6 0 Flange DN 00 PN 6 Form C, DIN 50/ B 6 Alloy C (.60) plated Flange DN 00 PN 6 Form C, DIN 50/ECTFE ) B 6 Flange DN 00 PN 6 Form C, DIN 50/PFA ) B 6 3 Flange DN 00 PN 6 Form D, DIN 50/36L B 6 Flange DN 00 PN 6 Form F, DIN 50/36L B 6 5 Flange DN 00 PN 6 Form N, DIN 50/36L B 6 6 Flange DN 00 PN 0 Form C, DIN 50/36L B 6 7 Flange DN 00 PN 0 Form C, DIN 50/ECTFE ) B 6 8 Flange DN 00 PN 0 Form C, DIN 50/PFA ) B 7 0 Flange DN 00 PN 0 Form C, DIN 50/ Enamelled 3) B 7 Flange DN 00 PN 0 Form F, DIN 50/36L B 7 Flange DN 00 PN 0 Form N, DIN 50/36L B 7 3 Flange DN 00 PN 0 V3, DIN 50/36L B 7 Flange DN 00 PN 6 Form E, DIN 50/36L B 7 5 Flange DN 00 PN 00 Form E, DIN 50/36L B 7 6 Flange DN 00 PN 00 Form L, DIN 50/36L B 7 7 Flange DN 5 PN 6 Form F, DIN 50/36L B 7 8 Flange DN 5 PN 0 Form C, DIN 50/36L B 8 0 Flange DN 5 PN 0 Form N, DIN 5/36L B 8 Flange DN 50 PN 6 Form C, DIN 50/36L B 8 Flange DN 50 PN 6 Form C, DIN 50/ B 8 3 Alloy C (.60) plated Flange DN 50 PN 6 Form C, DIN 50/ECTFE ) B 8 Flange DN 50 PN 6 Form C, DIN 50/PFA ) B 8 5 Flange DN 50 PN 6 Form D, DIN 50/36L B 8 6 Flange DN 50 PN 0 Form C, DIN 50/36L B 8 7 Flange DN 50 PN 0 Form C, DIN 50/ B 8 8 Alloy C (.60) plated Flange DN 50 PN 0 Form F, DIN 50/36L C 0 0 Flange DN 50 PN 0 Form N, DIN 5/36L C 0 Flange DN 00 PN 0 Form C, DIN 50/ECTFE ) C 0 Flange DN 00 PN 6 Form C, DIN 50/36L C 0 3 Flange DN 5 PN 0 Form B, EN 09-/36L C 0 Flange DN 5 PN 0 Form B, EN 09-/ C 0 5 Alloy C (.60) plated Flange DN 5 PN 0 Form B, EN/36L/PFA ) C 0 6 Flange DN 5 PN 0 Form B, EN 09-/ Enamelled 3) C 0 7 Flange DN 5 PN 0 Form B, EN 09-/36L C 0 8 Flange DN 5 PN 0 Form F, EN 09-/36L C 0 Flange DN 5 PN 63 Form B, EN 09-/36L C Flange DN 5 PN 00 Form B, EN 09-/36L C Flange DN 0 PN 0 Form B, EN/36L C 3 Flange DN 0 PN 0 Form B, EN 09-/PFA ) C Flange DN 0 PN 0 Form B, EN/36L C 5 Siemens FI 0 Update /07 /79

10 , Rigid extension in liquid applications such as overflow, high, 7ML low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Flange DN 50 PN 0 Form B, EN/36L C 6 Flange DN 50 PN 0 Form B, EN 09-/ C 7 Alloy C (.60) plated Flange DN 50 PN 0 Form B,EN 09-/ C 8 Alloy 00 (.360) ZB977 Flange DN 50 PN 0 Form B, EN 09-/ECTFE ) C 0 Flange DN 50 PN 0 Form B, EN/36L/PFA ) C Flange DN 50 PN 0 Form B, EN 09-/ Enamelled 3) C Flange DN 50 PN 0 Form C, EN 09-/36L C 3 Flange DN 50 PN 0 Form D, EN/36L C Flange DN 50 PN 0 Form D, EN 09-/ C 5 Alloy C (.60) plated Flange DN 50 PN 0 Form B, EN 09-/36L C 6 Flange DN 50 PN 0 Form E, EN 09-/36L C 7 Flange DN 80 PN 0 Form B, EN 09-/36L C 8 Flange DN 80 PN 0 Form B, EN 09-/ C 3 0 Alloy C (.60) plated Flange DN 80 PN 0 Form B, EN 09-/ECTFE ) C 3 Flange DN 80 PN 0 Form B, EN 09-/ Enamelled 3) C 3 Flange DN 80 PN 0 Form B, EN 09-/36L C 3 3 Flange DN 00 PN 6 Form B, EN 09-/36L C 3 Flange DN 00 PN 6 Form B, EN 09-/ C 3 5 Alloy C (.60) plated Flange DN 00 PN 6 Form B, EN 09-/ Enamelled 3) C 3 6 Flange DN 00 PN 0 Form B, EN 09-/36L C 3 7 Flange DN 00 PN 0 Form B, EN 09-/ Enamelled 3) C 3 8 Flange DN 00 PN 0 Form C, EN 09-/36L C 0 Flange DN 00 PN 63 Form B, EN 09-/36L C Flange DN 50 PN 6 Form B, EN 09-/36L C Flange DN 50 PN 6 Form B, EN 09-/PFA ) C 3 Flange DN 50 PN 0 Form B, EN 09-/36L C Flange DN 50 PN 0 Form B, EN 09-/ECT- FE ) C 5 Flange DN 50 PN 0 Form B, EN 09-/36L C 6 Flange " 50 lb ASME B6.5/36L C 7 Flange "50 lb RF, ASME B6.5/Alloy C (.60) C 8 plated Flange "50 lb RF, ASME B6.5//Alloy 00 C 5 0 (.360) ZB977 Flange " 50 lb RF, ASME B6.5/ECTFE ) C 5 Flange "50 lb RF, ASME B6.5/PFA ) C 5 Flange " 50 lb RF, ASME B6.5/Enamelled 3) C 5 3 Flange " 300 lb RF, ASME B6.5/36L C 5 Flange " 300 lb RF, ASME B6.5/ECTFE ) C 5 5 Flange " 600 lb RF, ASME B6.5/36L C 5 6 Flange ½" 50 lb RF, ASME B6.5/36L C 5 7 Flange ½" 50 lb RF, ASME B6.5/ C 5 8 Alloy C (.60) plated Flange ½" 50 lb RF, ASME B6.5/ECTFE ) C 6 0 Flange ½" 50 lb RF, ASME B6.5/PFA ) C 6 Flange ½" 50 lb RF, ASME B6.5 Enamelled 3) C 6 Flange ½" 50 lb FF, ASME B6.5/ECTFE ) C 6 3 Flange ½" 300 lb RF, ASME B6.5/36L C 6 Flange ½" 300 lb RF, ASME B6.5/ C 6 5 Alloy 00 (.360) ZB977 Flange ½" 300 lb RF, ASME B6.5/ECTFE ) C 6 6, Rigid extension in liquid applications such as overflow, high, 7ML low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Flange ½" 600 lb RF, ASME B6.5/36L C 6 7 Flange " 50 lb RF, ASME B6.5/36L C 6 8 Flange " 50 lb RF, ASME B6.5/Alloy C C 7 0 (.60) plated Flange " 50 lb RF, ASME B6.5/ C 7 Alloy 00 (.360) ZB977 Flange " 50 lb RF, ASME B6.5/ECTFE ) C 7 Flange " 50 lb RF, ASME B6.5/PFA ) C 7 3 Flange " 50 lb RF, ASME B6.5/Enamelled 3) C 7 Flange " 50 lb FF, ASME B6.5/36L C 7 5 Flange " 50 lb FF, ASME B6.5/ECTFE ) C 7 6 Flange " 50 lb SG (small groove), C 7 7 ASME B6.5/36L Flange " 300 lb RF, ASME B6.5/36L C 7 8 Flange " 300 lb RF, ASME B6.5/Alloy C C 8 0 (.60) plated Flange " 300 lb RF, ASME B6.5/ECTFE ) C 8 Flange " 300 lb RF, ASME B6.5/PFA ) C 8 3 Flange " 300 lb RJF, ASME B6.5/36L C 8 5 Flange " 300 lb ST, ASME B6.5/36L C 8 6 Flange " 300 lb LG (large groove), C 8 7 ASME B6.5/36L Flange " 300 lb LT, ASME B6.5/36L C 8 8 Flange " 600 lb RF, ASME B6.5/36L D 0 0 Flange " 600 lb RF, ASME B6.5/Alloy 00 D 0 (.360) ZB977 Flange " 600 lb RF, ASME B6.5/ECTFE ) D 0 Flange " 600 lb RJF, ASME B6.5/36L D 0 3 Flange " 600 lb LG, ASME B6.5/36L D 0 Flange " 900 lb RJF, ASME B6.5/36L D 0 5 Flange ½" 50 lb RF, ASME B6.5/36L D 0 6 Flange ½" 300 lb RF, ASME B6.5/36L D 0 7 Flange 3" 50 lb RF, ASME B6.5/36L D 0 8 Flange 3" 50 lb RF, ASME B6.5/Alloy C D 0 (.60) plated Flange 3" 50 lb RF, ASME B6.5/Alloy 00 D (.360) ZB977 Flange 3" 50 lb RF, ASME B6.5/ECTFE ) D Flange 3" 50 lb RF, ASME B6.5/PFA ) D 3 Flange 3" 50 lb RF, ASME B6.5/Enamelled 3) D Flange 3" 50 lb FF, ASME B6.5/36L D 5 Flange 3" 50 lb FF, ASME B6.5/ECTFE ) D 6 Flange 3" 50 lb FF, ASME B6.5/PFA ) D 7 Flange 3" 300 lb RF, ASME B6.5/36L D 8 Flange 3" 300 lb RF, ASME B6.5/Alloy C D 0 (.60) plated Flange 3" 300 lb RF, ASME B6.5/ECTFE ) D Flange 3" 300 lb RF, ASME B6.5/PFA ) D Flange 3" 300 lb RF, ASME B6.5/Enamelled 3) D 3 Flange 3" 600 lb RF, ASME B6.5/36L D Flange 3½" 50 lb RF, ASME B6.5/36L D 5 Flange 3½" 50 lb RF, ASME B6.5/ECTFE ) D 6 Flange " 50 lb RF, ASME B6.5/36L D 7 Flange " 50 lb RF, ASME B6.5/Alloy C D 8 (.60) plated Flange " 50 lb RF, ASME B6.5/ECTFE ) D 3 0 Flange " 50 lb RF, ASME B6.5/PFA ) D 3 Flange " 50 lb RF, ASME B6.5/Enamelled 3) D 3 Flange " 50 lb LT, ASME B6.5/36L D 3 3 /80 Siemens FI 0 Update /07

11 , Rigid extension in liquid applications such as overflow, high, low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. 7ML Flange " 300 lb RF, ASME B6.5/36L D 3 Flange " 300 lb RF, ASME B6.5/Alloy C D 3 5 (.60) plated Flange " 300 lb RF, ASME B6.5/ECTFE ) D 3 6 Flange " 300 lb RJF, ASME B6.5/36L D 3 7 Flange " 300 lb LG, ASME B6.5/36L D 3 8 Flange " 300 lb LT, ASME B6.5/36L D 0 Flange " 600 lb RF, ASME B6.5/36L D Flange " 600 lb RJF, ASME B6.5/36L D Flange 5" 50 lb RF, ASME B6.5/36L D 3 Flange 6" 50 lb RF, ASME B6.5/36L D Flange 6" 50 lb RF, ASME B6.5/Alloy C D 5 (.60) plated Flange 6" 50 lb RF, ASME B6.5/ECTFE ) D 6 Flange 6" 50 lb RF, ASME B6.5/PFA ) D 7 Flange 6" 50 lb RJF, ASME B6.5/36L D 8 Flange 6" 300 lb RF, ASME B6.5/36L D 5 0 Flange 8" 50 lb RF, ASME B6.5/36L D 5 Flange 8" 50 lb RF, ASME B6.5/ECTFE ) D 5 Flange " BS.0 Table E/36L D 5 3 Flange " BS.0 Table E/PFA ) D 5 Flange ½" BS.0 Table E/36L D 5 5 Flange 3½" BS.0 Table E/36L D 5 6 Flange " BS.0 Table E/ECTFE ) D 5 7 Flange DN 0 0K, JIS/36L D 5 8 Flange DN 50 0K, JIS/36L D 6 0 Flange DN 80 0K, JIS/36L D 6 Flange DN 00 0K, JIS/36L D 6 Thread R PN6, EN06-/36L ) D 6 5 Flange " 900 lb RF, ASME B6.5/36L D 7 0 Flange " 50 lb RF, ASME B6.5/Alloy C D 7 (.60) solid Adapter/Process temperature Without adapter/ C With adapter/ C 3) With adapter/ C 0) 3 With gas-tight leadthrough/ C With gas-tight leadthrough/ C 0) 5 Housing/Cable entry Aluminum IP66/IP67/M0 x.5 A Aluminum IP66/IP67/½" NPT B 36L stainless steel (electropolished) C IP66/IP67/M0 x.5 36L stainless steel (electropolished) D IP66/IP67/½" NPT Plastic single chamber IP66/IP67/M0 x.5 E Plastic single chamber IP66/IP67/½" NPT F Stainless steel chamber (precision casting) IP66/IP67/M0 x.5 G Stainless steel chamber (precision casting) H IP66/IP67/½" NPT Aluminum IP66/IP67/M0 x.5 Special HARTING V plug (bent) according to Tier One (ZB7555) NOTE: When selecting a Rigid Extension option, extension coating must match the process connection coating and the material and surface roughness type. Rigid Extension 36L mm A mm A mm A, Rigid extension in liquid applications such as overflow, high, 7ML low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications mm A mm A mm A mm A mm A 7 Rigid Extension ECTFE coated mm B mm B mm B mm B mm B mm B 5 Rigid Extension PFA coated mm C mm C mm C mm C mm C mm C mm C mm C 7 Rigid Extension 36L Ra 0.8 μm mm D mm D mm D mm D mm D mm D mm D mm D 7 Rigid Extension 36L Ra 0.3 μm mm E mm E mm E mm E mm E mm E mm E mm E 7 Rigid Extension Enamelled version mm F mm F mm F mm F mm F mm F 5 Rigid Extension Alloy C (.60) mm G mm G mm G mm G mm G mm G mm G mm G 7 Siemens FI 0 Update /07 /8

12 , Rigid extension 7ML577- in liquid applications such as overflow, high, low, and demand applications, as well as pump protection. For use in SIL- and hazardous applications. Rigid Extension Alloy 00 (.360) mm H mm H mm H mm H mm H mm H 5 Order code Further designs Please add "-Z" to and specify Order code(s). Switching status indication with colors red-green ) A Cleaning including Certificate W0 (oil, grease, and silicone free) Enter the total insertion length in plain text Y0 description, max. 000 mm (57.8 inch) Identification label (measurement loop) stainless Y7 steel: max. 0 characters, add in plain text. To add more than one line, use a coma "," for line break. Identification Label (measurement loop) foil: Y8 max. 0 characters add in plain text. To add more than one line, use a coma "," for line break. NACE075 to 3. Material Certificate for material D07 (EN00 NACE MR 075) 8) Note: not available with Process connection and Rigid extension coatings PFA, ECTFE, and Enamel. NACE not available with Hygienic process connections..-factory certificate for material (EN 00) 8) C5 Functional Safety (SIL ). Device suitable for use in C0 accordance with IEC 6508 and IEC 65 8) Dye penetration test, results confirmed via a C3 3. certificate/instrument (EN 00) 8) X-ray test + 3. certificate/instrument 8) C Positive material identification test C certificate/instrument 8) Roughness test + 3. certificate/instrument 8) C8 3.-Inspection Certificate for instrument with test C5 data (EN 00) Quality and test plan C6 Pressure test + 3. certificate/instrument 8) C3 Helium leak test + 3. certificate/instrument 8) C3 Ferrite measuring accuracy to DIN 35- C certificate/instrument 8) Pressure test according to Norsok C certificate/instrument 8) Operating Instructions All literature is available to download for free, in a range of languages, at processinstrumentation/documentation Spare Parts and Accessories Electronics module Relay Electronics module Contactless NAMUR spare electronics module Lock fitting, unpressurized, G" A/36L Lock fitting, unpressurized, " NPT/36L Lock fitting, unpressurized, G.../" A/36L Lock fitting, unpressurized,... /" NPT/36L Lock fitting, bar, G" A/36L Lock fitting, bar, " NPT/36L Lock fitting, bar, G... /" A/36L Lock fitting, bar,... /" NPT/36L Lock fitting, bar, G" A/36L Lock fitting, bar, " NPT/36L Lock fitting, bar, G... /" A/36L Lock fitting, bar,... /" NPT/36L 7ML830-NC 7ML930-6AA A5E ML930-DQ 7ML930-DR 7ML930-DS 7ML930-DT 7ML930-DU 7ML930-DV 7ML930-DW 7ML930-DX 7ML930-EA 7ML930-EB 7ML930-EC 7ML930-ED ) Available only with Adapter/Process temperature options, 3,, and 5. ) Available only with Housing/Cable entry option B. 3) Available only with Adapter/Process temperature options,, and. ) Not available with Adapter/Process temperature options, 3, and 5. 5) Not available with Adapter/Process temperature options,, and 5. 6) Available only with Electronics options and 6. 7) Available only with rigid extension options less than 3 00 mm. 8) Listed Certificates are not available with all configurations please contact factory for more information. 9) Not available with Housing/Protection/Cable option V. 0) Not available with PFA, ECTFE, and enamelled coating options. ) Available only with some 36L extensions. ) Available only with relay electronic options and non-hazardous Approval options. 3) Available only with Enamelled Process connection/material options. ) Not available with Approval options C, E, G, H, L, N, V, and W. 5) Not available with Approval options C, E, G, H, N, and V. 6) Only available with Aluminum Housing/Protection/Cable options and certain glands. 7) Not available with Stainless Steel Electropolish Housing/Protection/Cable options and certain glands. 8) Not available with Plastic or Stainless Steel Electropolish Housing/Protection/Cable options and certain glands. 9) Not available with Housing/Protection/Cable options D and V. 0) Not available with Housing/Protection/Cable options A, E, G, and V. ) Not available with some Housing/Protection/Cable gland options. ) Not available with Housing/Protection/Cable options A, C, and V. /8 Siemens FI 0 Update /07

13 SITRANS SCSC, single channel, signal conditioner for Single channel signal conditioning instrument for level detection with relay output for one LVL vibrating switch with electronics version two-wire 8/6 ma. Provides remote test of LVL00. Click on the for the online configuration in the PIA Life Cycle Portal. Approvals For Ex-free area ATEX II () G/D [Ex ia Ga/Da] IIC/IIIC, I (M) [Ex ia Ma] I IEC [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I SIL qualification 7ML A A D Without Version Single-channel (8/6 ma) for level detection Single channel (8/6 ma), level detection with fail safe relay Housing/cable entry Plastic/IP0 A Terminal block connection Detachable.5 mm²/ Ex sensor: x blue; output A and operating voltage: x black Detachable.5 mm²/ sensor: x black; output B and operating voltage: x black Language English 0 German Operating Instructions All literature is available to download for free, in a range of languages, at processinstrumentation/documentation H Order code SITRANS TCSC, two channel, signal 7ML576- conditioner for 7 7 A Two channel signal conditioning instrument for level detection with relay output for two LVL vibrating switches with electronics version two-wire 8/6 ma. Provides remote test of LVL00. Click on the for the online configuration in the PIA Life Cycle Portal. Approvals For Ex-free area ) A ATEX II () G/D [Ex ia Ga/Da] IIC/IIIC, I (M) D [Ex ia Ma] I ) IEC [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I ) H SIL qualification Without Version Double-channel (8/6 ma) for level detection Housing/cable entry Plastic/IP0 A Terminal block connection Detachable.5 mm²/ Ex sensor: x blue; A output and operating voltage: x black Detachable.5 mm²/ sensor: x black; B output and operating voltage: x black Language English 0 German Operating Instructions All literature is available to download for free, in a range of languages, at processinstrumentation/documentation ) Available only with terminal block connection option B ) Available only with terminal block connection option A Order code Siemens FI 0 Update /07 /83