BOSTITCH INSTALLATION ADJUSTMENT and MAINTENANCE MANUAL

Size: px
Start display at page:

Download "BOSTITCH INSTALLATION ADJUSTMENT and MAINTENANCE MANUAL"

Transcription

1 BOSTITCH INSTALLATION ADJUSTMENT and MAINTENANCE MANUAL WARNING: MODELS S13A1, S13B2, S13C AND S13E S25A1, S25B2 AND S25C METAL STITCHERS % CROWN -NO. 18 WIRE NEVER OPERATE MACHINE WITH WIRE FEEDING AND NO MATERIAL ABOVE CLINCHER. SERIOUS DAMAGE MAY RESULT. EXCESSIVE AMOUNT OF LUBRICANT MAY BLEED CAUSING DAMAGE TO WORK BEING STITCHED. IN OPERATING A STITCHER, BE CAREFUL NOT TO DRIVE ONE STITCH OVER ANOTHER, AS THIS MAY BREAK THE DRIVER TIPS. DO NOT OPERATE THE STITCHER WITH WIRE FEED ON BUT WITHOUT MATERIAL BETWEEN DRIVER AND CLINCHER. IF A PIECE OF WIRE GETS CAUGHT IN THE GRIPPER OR FORMER OR SHOE, STOP THE MACHINE AND REMOVE CAREFULLY BEFORE ATTEMPTING TO STITCH AGAIN. 1. INTRODUCTION A wire stitcher, like any other machine, will give satisfactory results to its owner only if properly installed, regularly lubricated, intelligently adjusted, and carefully maintained. Moving parts will wear in time and require replacement, while others may break through accident. Trained service men are available but not always to be had at a moment's notice, and a knowledgeof thefunctionsof themore important parts of a stitcher is therefore most desirable for every person responsible for its operation, in order to know what to do in case of trouble. We have, therefore, gathered together the combined experience of our engineers and service men and have attempted to present the information in a manner that will make it quickly available and readily understood. We would urge, however, in any case of serious difficulty that you notify our nearest sales office, sending samples of the defective work and describing the trouble in detail, so as to obtain the benefit of their experience in arriving at the proper solution. Be sure to report the serial number and model of the machine when corresponding in regard to equipment, so that it may be identified quickly. 2. INSTALLATION (See charts and parts lists for locations and names of parts referred to.) Any machine can be seriously damaged during its installation if it is not properly set up; therefore, we recommend close adherence to the following procedure: (a) After uncrating machine, examine carefully for any breakage in transit. If such be found, do not attempt to run machine but report at once to the selling agent. If our service man is present, let him examine machine and then report to the manufacturer. (b) See that motor is free to revolve when large pulley or flywheel is turned by hand. If tight, clutch is perhaps engaged, in which case shaft will turn also. Turning pulley or flywheel one revolution will release clutch. (c) Examine name plate on motor and see that its specifications are the same as those of the power to be used. If not, do not attempt to operate the machine. (d) Place the machine on a level floor, using shims under base if necessary to prevent any movement or rocking. (e) Lower clincher to at least 2" below the stitcher head, by means of adjusting sleeve on post type stitcher, orclincherbracketadjustingscrewon head mounted clincher bracket stitcher or clincher arm adjusting screw or bolt on arm type stitcher. (f) Be sure that the machine isoiledthoroughlyat all points before operating. Run a little oil on coil of wire, which helps to lubricate wire feed tubes and also the formers and driver, which are tight-fitting when new. Tie a piece of cloth temporarily around the wire above the top end OT tne upper wire Teed tube to remove dirt and excess oil and thus prevent soiling the work. (g) Connect motor cord to power outlet and start motor. See that it runs freely, without undue noise,

2 and that the large pulley rotates clockwiseasviewed from the front of the machine. Should it rotate counter-clockwise, motor wiring should be reconnected by an electrician in order to reverse direction of rotation. (h) Push down foot switch treadle and thus start machine operating, starting and stopping several times. (i) Stop motor, and with connecting link arm pulled down, turn pulley by hand until driver is at lowest point. (j) With driver in lowest position and work to be stitched under same, raise clincher post, bracket, or arm, until work is held firmly. Then lock post, bracket, or arm, in position..(k) Place a spool of wire of proper size on the spoolholder, the wire leading to the left from top of spool, then tighten spool-holderspindlejam nut just enough to give a slight drag to the rotation of spool and prevent the wire uncoiling. If it is too tight, the wire will bind and catch between the coils and thus may cause uneven staple legs. If too loose, the spool may unwind, causing snags in the wire. Cut binding wires on wire coil and bend same back over edge of spool, holding free end of wire in the hand to prevent unwinding and tangling. Cut off bent and twisted end of the wire, then straighten out about 6". The end of the wire to be inserted in machine must be just as straight as possible. Open wire feed gears by raising idler feed gear throwout handle and insert end of wire through eye on upper end of the spring wire guide. Enter the end of the wire into the upper wire tube, push down between the wire feed gears, then through the lower wire tube and between wire straightener rolls. Push it into the hole in the stationary cutter, raising the end of the wire slightly if necessary for proper entrance, then turn down the idler feed gear throwout handle, thus engaging the feed gears. WARNING: NEVER OPERATE MACHINE WITH WIRE FEEDING AND NO MATERIAL ABOVE CLINCHER. SERIOUS DAMAGE MAY RESULT. (I) Start motor and drive a few stitches into material and, if necessary, adjust clincher height to get desired tightness of clinching. See instructions for adjusting clincher. (m) Adjust for proper length of wire by loosening lock screw and moving wire feed guard casting to rightor left along gauge marks on upper part of head casting. Moving to left reduces wire draw while moving to right increases it. When set at mark "0", head will draw one inch of wire and each mark indicates an additional 1 / 8 " in length. When proper length of wire is being drawn, tighten lock screw in place firmly. (n) Drive several rows of stitches into material to be used, examining crown and legs for proper appearance. If not satisfactory, adjust machine in accordance with directions given hereafter. NOTE: When changing length of wire draw, the first stitch driven, and perhaps the second, will beof the previously used length since it is formed from a piece of wire already cut and held in the anvil. The third stitch, however, will be of the new length ADJUSTMENT AND MAINTENANCE The following paragraphs cover briefly the various functions and operating parts of a stitcher and also give the proper methods of adjustment and replacement of parts. Every Stitcher should be oiled daily, and if machine is in constant use, twicedaily.theoil holes and cups are easily found on stitcher head and body. A heavier type of oil should be used for the former and drive bar. A light machine oil should be usedfor remainder of head. CAM LUBRICATING INSTRUCTIONS:-Trip clutch and rotate drive pulley manually, if necessary, in direction indicated by arrow on pulley until grease fitting on cam is aligned with hole in lubricating cover unit located in body or head casing. When fitting is visible thru hole in lubricating cover unit, lubricant can be applied with a grease gun to fit alemite hydraulic fitting (straight type). It is recommended that the cam be greased once monthly with Harris Moly-Lube #2 (high temperature) lubricant or equivalent. WARNING: EXCESSIVE AMOUNT OF LUBRI- CANT MAY BLEED CAUSING DAMAGE TO WORK BEING STITCHED. (a) Clutch Clutch should be oiled frequently with light machine oil. Never let clutch run dry. To oil, turn collar at end of shaft until oil hole is exposed. Put a few drops of oil into brake band occasionally. If the clutch hesitates on picking up, turn lower \ brake adjusting screw in or clockwise about 1 / 4 to V 2 turn, or until clutch picks up. If the clutch repeats, the lower brake adjusting screw should be backed out until clutch does not repeat. Be sure, however, that the BRAKE BAND IS FREE when the clutch is in operation or engaged. Clean out the Clutch Ring and Flywheel with kerosene or any cleaning solvent. It is not necessary to take the Clutch out. Squirt the cleaning fluid into the Flywheel and Clutch Ring and run the machine for a few moments, continuously starting and stopping. NOTE: Proper action of clutch and brake is as follows: When clutch engages, brake band should be free and when clutch is disengaged, brake band should be tight and clutch should be free. When clutch ring wears beyond point of contact, replace pins #2347 with pins #2347A. The following figures will identify expanding pins referred to: No pin is.156" thick No. 2347A pin is.166" thick Thickness is determined by measuring the pin from the flat side to the opposite round side with a micrometer. NOTE: When replacing rings in clutch unit, the heads of the expanding pins for the brake ring and clutch ring must be facing each other. (b) Clincher The clincher must be lined up with the staple as

3 closely as possible to insure maximum ease of penetration through work by the staple, as well as to clinch staple properly. TO ADJUST CLINCHER SIDEWAYS ' V S13A1 and S25A1 Stitchers 1. Loosen post pivot cup clamp screws, and post brace lock nuts at post end. 2. Adjust post in direction desired, by means of post pivot cup adjusting screws. For example: To move post to the right, back out right hand screw and turn in left hand screw as much as necessary to locate clincher correctly. Turn in right hand screw until post is held solidly. 3. Tighten post pivot cup clamp screws and post brace lock nuts. S73C and S13E Stitchers 1. Loosen bottom nut on clincherarm adjusting bolt (on S13E only). 2. Loosen lock nuts on clincher arm side adjusting screws. 3. Adjust arm in direction desired by means of clincher arm side adjusting screws. For example: If arm must be moved to the right, back out the right hand screw and turn in the left hand screw as much as necessary. Turn in right hand screw until arm is held solidly. 4. Tighten lock nuts on clincher arm side adjusting screws. Tighten bottom nut on clincher arm adjusting bolt on S13E Stitcher only. I '! S25C Stitcher V_- j 1. Loosen arm adjusting screw set screw UA Loosen arm clamp screws UA Adjust arm by means of arm adjusting screw UA Tighten rear clamp screw and check for correct position. Readjust if necessary. 5. Tighten both clamp screws securely.tighten arm adjusting set screw UA TO ADJUST CLINCHER FORWARD OR BACK S13A1 and S25A1 Stitchers 1. Adjust post in direction desired by means of lock nuts at forward end of post brace. For example: -To move post forward, loosen nut at front of post and turn nut at back of post until desired position is reached. Then tighten nut at front end. S73C and S25C Stitchers 1. Loosen Clincher holder screws, push clincher forward or back to suit. Tighten clincher holder screws. S13E Stitcher 1. Loosen bottom nut on arm adjusting bolt and locknuts on arm side adjusting screws. Back out adjusting screws slightly. _? 2. Adjust arm in or out by turning arm pivot pin to right or left as required. 3. Return arm side adjusting screws to original setting and tighten lock nuts. 4. Adjust arm vertically, if necessary, by means of the two nuts on arm adjusting bolt Check adjustment of clincher operating slide by turning machine over by hand and watching clincher slide. If there is any tendency to bind, loosen lock nut under arm and back out set screw one or two turns. When'clincher cam has reached its maximum throwout position turn this screw in until clincher slide is flush with top of clincher. Tighten lock nut and turn over by hand again to be sure nothing binds. 6. Check all adjustments to be sure all are tight and try machine once or twice on scrap pieces of material. The arm should be adjusted so that the work will be just held between formers and clincher and should not deflect enough while the staple is being driven to cause loss of contact between formers and work. TO ADJUST ARM UP OR DOWN ON S25C 1. Loosen arm clamp screws UA Loosen lock nuts on arm elevating screw UA Tighten arm clamp screw lightly. Turn machine over by hand and check for space between clincher and bottom of formers. Turn arm elevating screw UA9076 in the required direction to obtain the space desired. Tighten clamp screws and arm elevating screw lock nuts secureiy. (c) Stitching Wire When stitching metal it has been found that #18 wire is best suited to the majority of work. This wire can be had in various degrees of hardness or temper, such as #18 Bookbinders wire, which is the softest, #18-230, #18-260, # and # It is impossibletogivethe exact thickness of metal which a given temper of wire will penetrate. Roughly, Bookbinders wire will penetrate a single thickness of.020 soft steel; #18-230, two thicknesses of.020 (total.040); #18-260, two thicknesses of.040 (total.080); #18-290, one thickness of.060 plus.030 (total.090); # two thicknesses of.060 (total.120). If the metal is too hard, there may be trouble in stitching so great a thickness; on the other hand, if the metal is soft, the thickness may be increased. When stitching a soft material like fibre or rubber to metal, especially if this material is thick, there may be trouble in penetrating the metal due to lack of support for the wire in the soft material. For this purpose, the # wire may help, in which case special spool holder equipment will be required. It is best to use the softest wire that will penetrate the work safely, as the harder wire will cause more wear on the machine. (d) WARNING: IN OPERATING A STITCHER, BE CAREFUL NOT OT DRIVE ONE STITCH OVER ANOTHER, AS THIS MAY BREAK THE DRIVER TIPS. DO NOT OPERATE THE STITCHER WITH WIRE FEED ON BUT WITHOUT MATERIAL BETWEEN DRIVER AND CLINCHER. IF A PIECE OF WIRE GETS CAUGHT IN THE GRIPPER OR FORMER OR SHOE, STOP THE MACHINE AND REMOVE CAREFULLY BEFORE ATTEMPTING TO STITCH AGAIN.

4 S13A1 STITCHER NOTE: SEE S13C STITCHER CHART (PAGE 7) FOR BODY, BASE, DRIVE AND TRIP PARTS. fl

5 Ul I

6 SI3C STITCHER UA H6 831H2

7 / \, ' 1 1, I I - -" t^-" ""^ i ^f**^ i ^^^^ *^- v^** i t --' i _- - ^ UB

8 S13E STITCHER oo i BA 446H HA 18283JA/1S281DA ^ 36571BA 36575D 36576C

9 36523A 36551BA B 36547B \_36544_ 36543B UB OV-AC V-AC V-DC CO

10 S25C STITCHER 93 H JA DA 830H13 831H11 UA UA UA8840J3 UB4124. J

11 ( L seer; FOR PARTS SPECIAL TO S25A1 & S25B2 STITCHERS SEE LIST IN REAR OF BOOK OV-AC V-AC V-DC

12 S13B2 STITCHER UA HN H15 NOTE: SEE S13C STITCHER CHART (PAGE 7) FOR BODY, BASE, DRIVE AND TRIP PARTS 821H -TOP CLINCHER MOUNTING (AS SHOWN) 821H2- BOTTOM CLINCHER MOUNTING SB825 _BG1_ H SPACER

13 FOOT SWITCH ASSEMBLY SINGLE TRIP MECHANISM 150H10 165H15 J «. / I 1 //I o si. / / / / A 840H Q5B 36554BA E_A *36606DA \ *FOR S25 STITCHERS - 13-

14 INSTRUCTIONS FOR USE OF JAM RELEASING WRENCH INSERT PINS IN WRENCH BSA37 INTO TWO HOLES IN DRIVE PULLEY WASHER 18281DA AND TURN IN THE DIRECTION SHOWN ON SKETCH WRENCH DRIVE PULLEY WASHER DA - 14-

15 CLUTCH AND BRAKE UNIT 2340B 446H HA UB MIN MAX. 2347A CLUTCH RING ASSEMBLY E JA

16 PLAIN CLINCHERS CLINCHERS FOR S13A1, S13B2, AND S13C STITCHERS RAISED CLINCHERS o OPEN END CLINCHING SURFACE (With 2 Drilled Holes) 830H6-45 Angle of Contact (Standard) S13C, S13B2 830H17-37y 2 Angle of Contact (With 2 Tapped Holes) 830H13-45 Angle of Contact (Standard) S25C CLINCHING SURFACE MILLED THRU 830H15-45 Angle of Contact Raised Vi" 830H21 45 Angle of Contact Raised 1" GROOVED CLINCHING SURFACE 830H39-45 Angle of Contact Raised W GROOVED CLINCHING SURFACE 830H11-45" Angle of Contact PASS-BY CLINCHING SURFACE 830H47 - Raised %" OPEN END CLINCHING SURFACE (With 1 Tapped Hole) 830H19-45 Angle of Contact GARNISH MOULDING CLINCHERS CLINCHING SURFACE MILLED THRU LIP 830H 45 Angle of Contact SINGLE CLINCHING SURFACE MILLED THRU 830H20-45 Angle of Contact Raised 2" POST CLINCHERS 280G - 45 Angle of Contact (Standard) 280G2-37 W Angle of Contact OPEN END CLINCHING SURFACE 830H24-45 Angle of Contact (Raised 3") 830H37-37'/ 2 " Angle of Contact (Raised 3") CLINCHER ADAPTERS 832H - For Use With V4", %" and 1" Raised Clinchers OPEN END CLINCHING SURFACE 830H8-45 Angle of Contact 832H2 - For Use With 2" Raised Clincher CLINCHER HOLDERS 831H2 -With Tapped Clincher Hole (Standard) S13C 831H11 -With Drilled Clincher Hole (Standard) S25C S31H7 - For Use With 3" Raised Clincher 830H24 (S13C Only) 831H8 - For Use With 3" Raised Clincher 830H24 (25C Only) Movable Clincher Solid Clincher Solid Clincher 37 'A" 45 Sectional View Showing Types of Clinchers W' -16-

17 PARTS FOR S13A1, S13B2, S13C, S13E, S25A1, S25B2 AND S25C STITCHERS 90H3 91H2 92H 93H 94H2 94H3 148H 164H8D 174H18 446H5 809H 840H 867H3 869H2 997H BD H f>340b * ^ DA 18283HA 18283JA BA B B A 36554BA O ^ Spoolholder Bracket Spoolholder Spindle Spoolhoider Thrust Washer Assem Spoolholder Friction Spring Spoolholder Lock Nut Spoolholder Spindle Jam Nut Drive Shaft Bushing (Back) Drive Cam Drive Pulley 9" Clutch Brake Band Assem. (9" Clutch) Drive Pulley Guard Clutch Sleeve Key Latch Latch Contact Spoolholder Lock Latch Spring Plunger Foot Switch Treadle Pivot BSA37 Latch Spring A Pulley Washer Screw Lock Spring Drive Bar Link Bushing Clutch Lever Clutch Lever Spring Plunger Brake Band Adjusting Screw Brake Band Adjusting Screw Lock Latch Pivot Stud HN1420 Clutch Ring Expanding Pin HN Pulley Washer Screw HN Pulley Washer Screw Lock Brake Band Adjusting Screw Lock Spring Pulley Washer Assem. Brake Ring Clutch Ring Assem. 9" Clutch Clutch Pawl Plunger Brake Band Assem. (4" Clutch) Clutch Lever Pivot Stop Plunger Spring Solenoid Connecting Link Pin Stop Plunger Clutch Pawl Brake Band Link Clip Solenoid Cover Plate Brake Band Link Brake Band Link Stud Clutch Sleeve Assem. Connecting Link Arm Single Trip Lever Single Trip Lever Pivot Single Trip Screw Solenoid Bracket Foot Switch Base Foot Switch Treadle PW516 SW6 UA UA UA UA UA UA UA UA UA UA UA UA UA UA UB UB UB Micro Switch Shield Foot Switch Treadle Spring Solenoid Connecting Link Spring Solenoid Spring Bracket Solenoid Connecting LinkSpring Retaining Washer Foot Switch Assem. Micro Switch Solenoid 110 Volt A.C. Solenoid 220 Volt A.C. Solenoid 230 Volt D.C. Oiler Drive Shaft Bushing (Front) Circuit Breaker Grease Fitting Pin Wrench (For re-setting Head) V Belt Motor Pulley (% Bore) for 295 Stitches per minute with 1725 R.P.M. Motor MotorPulley (% Bore) for295 Stitches per minute with 1425 R.P.M. Motor Motor Pulley (% Bore) for 295 Stitches per minute with 1425 R.P.M. Motor Solenoid Screw Nut Solenoid Spring Bracket Nut Switch Contact Screw Lock Nut HN Connecting Link Stop Nut HN Solenoid Connecting Link Pin Nut LW14 Solenoid Screw Lock Washer LW716 Solenoid Bracket Screw Lock Washer Pulley Guard Screw Washer Micro Switch Screw Lock Washer Micro Switch Screw Solenoid Cover Plate Screw Solenoid Screw Solenoid Spring Bracket Screw Pulley Guard Screw Spoolholder Bracket Screw Spoolholder Bracket Screw Pulley WasherScrew Lock Spring Screw SingleTrip Lever Pivot Block Screw (Short) SingleTrip Lever Pivot Block Screw (Long) Connecting Link Stop Screw Head to Body Screw Drive Cam Screw Motor Plate Stud Screw Spoolholder Thrust Washer Cotter Spoolholder Lock Nut Stop Pin Solenoid Spring Retaining Fin -17-

18 PARTS FOR S13A1, S13B2, S13C AND S13E STITCHERS 150H10 Body 151H35 1 / 2 Base 165H15 Drive Shaft 866H5 Stop Plunger Lever - Assem Clutch Lever Spring 36507B Motor Plate Motor Plate Stud 36541A Single Trip Lever Pivot Block Connecting Link Arm Pivot 36566EA Solenoid Connecting Link UA Guard Screw UA Body to Base Screw LW716 Body Screw Lock Washer UA Solenoid Bracket Screw UA Motor Plate Screw UA Motor Plate Stud Screw UA Clincher Arm Pivot Lock Screw PARTS FOR S25A1, S25B2, AND S25C STITCHERS 150J13 Body Q151L7 Base 178H8 Motor Plate 866H6 Stop Plunger Lever - Assem Clutch Lever Spring 36606DA Solenoid Connecting Link 36607A Drive Shaft 36618A Hand Trip Assembly LW58 Body Screw Lock Washer UA Solenoid Bracket Screw UA Post Binding Screw UA Body to Base Screw PARTS FOR S13A1 AND S25A1 STITCHERS 201G7 Post Pivot Head 202G7 Post Base 204G2 Post Pivot Pin 205G2 Post Pivot Pin Cup - Right Hand 206G2 Post Pivot Pin Cup - Left Hand 283G Post Adjusting Nut SB1204 Post Base Leveling Bushing HN5811 Post Brace Lock Nut HN Post Brace Lock Nut - (Front) LW58 Post Brace Lock Washer PW12 Post Base Screw Washer UA Clincher Screw UA Post Pivot Cup Adjusting Screw UA Post Pivot Cup Clamp Screw UA Post Pivot Head Lock Screw UA Post Base Screw UA Post Clamping Screw Note: See page 16 for Clinchers r 183H 183R2 186H2 282GA PARTS FOR S13A1 STTCHER ONLY Clincher Arm Locking Pin Clincher Arm Pivot Arm Hole Cover Plate Post Column Assem. 284G Post Brace 2338 Clincher Arm Locking Pin Plug Guard UA Arm Hole Cover Plate Screw UA Clincher Arm Lock Pin Screw 282G3A 284G3 PARTS FOR S25A1 STITCHER ONLY Post Column Assembled 36630A Single Trip Pivot Block Post Brace

19 PARTS FOR S13B2,AND S25B2 STITCHERS 129H5 Gripper Spring Pivot 821H Clincher Bracket - (Standard) for Top Clincher Mounting 821H2 Clincher Bracket for Bottom Clincher Mounting 824H Clincher Bracket Spacer BG1114 Clincher Bracket Screw Washer SB825 Clincher Bracket Screw - (Lower) Base Plate Clincher Bracket Screw Washer HN Clincher Bracket Adjusting Screw Lock Nut HN71614 Clincher Bracket Screw Nut PW38 Clincher Screw Washer UA ClincherScrew-ForTopClincherMounting UA Clincher Bracket Screw UA Clincher Bracket Adjusting Screw UA Base Plate Screw UA Clincher Screw-For Bottom Clincher Mounting Note: See page 16 for Clinchers 183H 183R2 186H2 PARTS FOR S13B2 STITCHER ONLY Clincher Arm Locking Pin 2338 Clincher Arm Locking Pin Plug Clincher Arm Pivot Guard Arm Hole Cover Plate UA Arm Hole Cover Plate Screw UA Clincher Arm Lock Pin Screw PARTS FOR S25B2 STITCHER ONLY 36630A Single Trip Lever Pivot Block PARTS FOR S13C STITCHER ONLY 183H Clincher Arm Locking Pin SB R2 Clincher Arm Pivot SW H27 Clincher Arm 189J2 Clincher Arm Adjusting Screw UA BG1304 Clincher Holder Washer UA Clincher Arm Locking Pin Plug UA Base Plate UA Guard UA HN Clincher Arm Side Adjusting Screw Lock Nut Note: HN Clincher Arm Adjusting Screw Lock Nut Clincher ArmSide Adjusting Screw Clincher Arm Side Adjusting Screw Lock Washer Clincher Screw Base Plate Screw Clincher Holder Screw Clincher Arm to Pivot Screw Clincher Arm Lock Pin Screw See page 16forClinchers,ClincherHolders, and Clincher Adaptors PARTS FOR S25C STITCHER ONLY WJ16 Arm Clincher Holder Washer Base Cover Arm Binding Screw Washer (Rear) 36630A Single Trip Pivot Block Arm Binding Screw Washer (Front) Wear Block 'UA Arm Adjusting Set Screw UA7H4.1 CKncfier Screw UA Base Cover Screw UA Clincher Holder Screw UA Arm Adjusting Screw UA9076 Arm Elevating Screw UA9160 Arm Clamp Screw HN5811 Arm Locating Screw Lock Nut

20 PARTS FOR S13E STITCHER ONLY BG300 Clincher Arm Adjusting EccentricSet Screw Plug Base Plate B512B Clincher Operating Lever Slide Pin A Clincher Arm HN Clincher Arm Pivot Pin HN A Clincher Arm Adjusting Eccentric HN Clincher Arm Adjusting Bolt HN Clincher Arm Adjusting Bolt Pin 36537A Clincher Cam Slide HN Clincher Cam Slide Roll HN Clincher Cam Slide Roll Retainer PW Clincher Cam Slide Plunger PW B Clincher Cam Slide Lever SW Clincher Operating Lever Pivot Clincher Cam Slide Lever Pivot UA B Push Rod 36547B Push Rod Guide UA C Push Rod Guide Spring Plate 36551BA Clincher Operating Slide UA Clincher Operating Slide Spring Clincher Operating Slide Spring Hook UA BA Clincher Holder UA D Clincher UA Clincher Screw UA D Clincher Slide UA C Clincher Operating Lever UA B Clincher Slide Tip UA Air Valve Bracket UA Air Valve Lever UA Air Valve Lever Pivot UA Air Tube UA Guard UA Ai r Tu be Adapto r Air Valve Air Petcock Air Petcock Nipple Air Line Coupler Air Valve Lever Pivot Screw Nut Air Valve Guard Screw Nut Clincher Arm Side Adjusting Screw Lock Nut ClincherOperating Slide Adjusting Screw Lock Nut Air Valve Screw Nut Clincher Arm Adjusting Bolt Nut Air Valve Lever Pivot Washer Air Valve Screw Washer Clincher Arm Side Adjusting Screw Lock Washer Clincher Operating Lever Pivot Retaining Screw ClincherCam Slide LeverPivot Retaining Screw Clincher Arm Adjusting Bolt Pin Retaining Screw Clincher Holder Screw Push Rod Guide Screw Air Valve Screw Air Valve Guard Screw Air Valve Bracket Screw Air Valve Lever Pivot Screw Air Valve Bracket Screw Clincher Cam Slide Roll Retainer Screw Base Plate Screw Clincher Arm Adjusting Eccentric Set Screw ClincherOperating Slide Adjusting Screw Clincher Arm Adjusting Screw / i n BOSTITCH Division of Textron Inc., East Greenwich, R. I , U.S.A. BSA 360 D 5-76 LITHO IN U.S.A.

OPERATOR'S MANUAL Model 23 or 24 Belt Drive Electric Seamer

OPERATOR'S MANUAL Model 23 or 24 Belt Drive Electric Seamer OPERATOR'S MANUAL Model 23 or 24 Belt Drive Electric Seamer Model 23-500 (shown) If you are not experienced with your seamer, please read and understand this manual before operating the machine. If you

More information

DIRECT DRIVE DIXIE DOUBLE SEAMER Model 25D

DIRECT DRIVE DIXIE DOUBLE SEAMER Model 25D OPERATOR'S MANUAL DIRECT DRIVE DIXIE DOUBLE SEAMER Model 25D LUBRICATE DAILY: A. Gears inside gear housing at chuck shaft (1) Oil B. Seam rolls and cam rolls (4) - Oil C. Seam roll levers through gear

More information

OPERATOR'S MANUAL DIRECT DRIVE DIXIE DOUBLE SEAMER Model 10D

OPERATOR'S MANUAL DIRECT DRIVE DIXIE DOUBLE SEAMER Model 10D OPERATOR'S MANUAL DIRECT DRIVE DIXIE DOUBLE SEAMER Model 10D OIL DAILY: A. Gears inside gear housing through oil groove in gear housing at cut surface of chuck shaft. (Oil through #517 gear housing cover

More information

Model 23H Hand Crank Seamer

Model 23H Hand Crank Seamer OPERATOR'S MANUAL Model 23H Hand Crank Seamer If you are not experienced with your seamer, please read and understand this manual before operating the machine. If you have a question discuss it with your

More information

44in Side Discharge Mower for Wheel Horse XL 440H Lawn Tractors Model No Serial No and Up

44in Side Discharge Mower for Wheel Horse XL 440H Lawn Tractors Model No Serial No and Up Form No. 5-8 in Side Discharge Mower for Wheel Horse XL 0H Lawn Tractors Model No. 790 Serial No. 5000000 and Up Operator s Manual Register your product at www.toro.com Original Instructions (EN) Contents

More information

7130 Lancer Rear Drive Magnetic Commercial Indoor Cycling Bike

7130 Lancer Rear Drive Magnetic Commercial Indoor Cycling Bike 7130 Lancer Rear Drive Magnetic Commercial Indoor Cycling Bike Owner s Manual Made in Taiwan INDEX IMPORTANT SAFETY INFORMATION... 1 EXPLODED DRAWING... 2 PARTS LIST... 3 ASSEMBLY INSTRUCTION... 4-9 USER

More information

CHAPTER 5 REWIND STARTERS

CHAPTER 5 REWIND STARTERS GENERAL INFORMATION CHAPTER 5 REWIND S Rewind starters used on vertical shaft Tecumseh engines are top mount horizontal pull style or side mount vertical pull style. Horizontal shaft engines use side mounted

More information

IMPORTANT: RECEIVING INSTRUCTIONS:

IMPORTANT: RECEIVING INSTRUCTIONS: Instruction Sheet Sidewinder Mechanical Bender IMPORTANT: RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any shipping damage is found, notify carrier at once.shipping damage

More information

3/8" Dr. Air Butterfly Impact Wrench

3/8 Dr. Air Butterfly Impact Wrench 8192106 3/8" Dr. Air Butterfly Impact Wrench Owner s Manual Read and understand all instructions before use. Retain this manual for future reference. Specifications Construction: Polished aluminum and

More information

MUELLER. A Wall Type. Indicator Post. Reliable Connections. General Information 2. Technical Data/ Dimensions 3. Installation 4-5.

MUELLER. A Wall Type. Indicator Post. Reliable Connections. General Information 2. Technical Data/ Dimensions 3. Installation 4-5. Installation Instructions manual MUELLER table of contents PAGE A-20814 Wall Type General Information 2 Technical Data/ Dimensions Installation 4-5 Maintenance 6 Parts 7 Indicator Post! WARNING: 1. Read

More information

Index Table. Model 794. Installation, Operating and Maintenance Instructions

Index Table. Model 794. Installation, Operating and Maintenance Instructions CLOCKWISE MANUAL MAKING INTO CCW TABLE Index Table Model 794 Installation, Operating and Maintenance Instructions Black & Webster Products Division 545 Hupp Ave. P.O. Box 831, Jackson, Michigan 49204 2009

More information

MUELLER. Mega-Lite Drilling Machine. Reliable Connections. table of contents PAGE. Equipment 2. Operating Instructions 3-4. Parts Information 5

MUELLER. Mega-Lite Drilling Machine. Reliable Connections. table of contents PAGE. Equipment 2. Operating Instructions 3-4. Parts Information 5 operating Instructions manual MUELLER Mega-Lite Drilling Machine table of contents PAGE Equipment 2 Operating Instructions 3-4 Parts Information 5 Travel Charts 6-11! WARNING: 1. Read and follow instructions

More information

44 Mower Wheel Horse 5xi Tractor Attachment

44 Mower Wheel Horse 5xi Tractor Attachment Form No. -660 44 Mower Wheel Horse 5xi Tractor Attachment Model No. 7857 890000 and Up Model No. 7858 890000 and Up Operator s Manual Domestic English (EN) Introduction We want you to be completely satisfied

More information

MUELLER GAS. No-Blo Operations Using D-5. Drilling Machine. Reliable Connections. General Information 2

MUELLER GAS. No-Blo Operations Using D-5. Drilling Machine. Reliable Connections. General Information 2 operating Instructions manual MUELLER GAS TAble of contents PAGE No-Blo Operations Using D-5 General Information 2 Installing No-Blo Service Tees, Service Stop Tees and Curb Stop Tees 3-8 Reconditioning

More information

MAGNETIC INDOOR CYCLING BIKE

MAGNETIC INDOOR CYCLING BIKE MAGNETIC INDOOR CYCLING BIKE SF-B1805 USER MANUAL IMPORTANT! Please retain owner s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL

More information

Santa Fe Cycles Assembly Guide Introduction

Santa Fe Cycles Assembly Guide Introduction Santa Fe Cycles Assembly Guide Introduction Congratulations on your purchase of your new Santa Fe bicycle. You have purchased a bicycle that has many features and qualities. Please take a few minutes and

More information

Lectric Cycles Mid-Drive Electric Motor Installation

Lectric Cycles Mid-Drive Electric Motor Installation Lectric Cycles Mid-Drive Electric Motor Installation This write-up describes the installation of a Lectric Cycles electric motor. The model is the e-rad Mid-Drive 750 Watt conversion kit, installed on

More information

SIGNATURE DEF REELS Models: Bare Reel Reel Reel Reel

SIGNATURE DEF REELS Models: Bare Reel Reel Reel Reel SERVICE BULLETIN SB2023 Rev C 7/11 SIGNATURE DEF REELS Models: 2400-006 Bare Reel 2400-007 16 Reel 2400-008 20 Reel 2400-009 30 Reel Thoroughly read and understand this manual before installing, operating

More information

MASTER TRUING STAND TS-3. Optional Dial indicator set with brackets Dial indicator bracket set only

MASTER TRUING STAND TS-3. Optional Dial indicator set with brackets Dial indicator bracket set only MASTER TRUING STAND TS-3 3 2 1 3 8 9 4 10 7 6 5 12 13 Optional 1555-1 Dial indicator set with brackets 1556-1 Dial indicator bracket set only 49 11 16 14 15 48 32 31 37 38 20 19 17 18 34 39 21 36 22 33

More information

OPERATOR'S MANUAL DIRECT DRIVE DIXIE DOUBLE SEAMER. Model 25D

OPERATOR'S MANUAL DIRECT DRIVE DIXIE DOUBLE SEAMER. Model 25D OPERATOR'S MANUAL DIRECT DRIVE DIXIE DOUBLE SEAMER Model 25D OPERATOR'S MANUAL DIRECT DRIVE DIXIE DOUBLE SEAMER MODEL 25D INTRODUCTION DESCRIPTION Dixie Model 25D series of double seamers are adaptable

More information

HOLLISTER-WHITNEY ROPE GRIPPER

HOLLISTER-WHITNEY ROPE GRIPPER HOLLISTER-WHITNEY ROPE GRIPPER Instructions for Model #620GA1, 620GA2 (US PATENT 8,511,437) WARNING: KEEP HANDS CLEAR OF ROPE GRIPPER. FORCES CREATED CAN CRUSH FINGERS. Figure 1 ROPE GRIPPER TM MOUNTING

More information

1650EXLT, ,

1650EXLT, , 1650EXLT, 96193008901, 2012-10 "CHASSIS, ENGINE & PULLEYS" - 000 00 00-00 W/O DESCRIPTION 1 B&S 21M307-0135-F1 FOR SERVICE & PARTS 1-800-233-3723 1 532 42 92-03 FRAME 1 2 532 15 04-06 BOLT 1 3 532 42 88-67

More information

OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP50-H-14 HYDRAULIC WINCH.

OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP50-H-14 HYDRAULIC WINCH. W. W. Patterson Company 3 Riversea Road Pittsburgh, PA 15233 Phone: 800-322-2018 FAX: 412-322-2785 OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP50-H-14 HYDRAULIC WINCH. Please fill in the following blanks

More information

AIR DRIVE ROLL FEED CARTON STAPLER MODEL: H-1031 MANUAL

AIR DRIVE ROLL FEED CARTON STAPLER MODEL: H-1031 MANUAL AIR DRIVE ROLL FEED CARTON STAPLER MODEL: H-1031 MANUAL WARNING Before operating this stapler familiarize yourself with the safety warnings and instructions in this manual. Keep these instructions with

More information

AR STYLE FIREARMS OWNER'S MANUAL: OPERATION, HANDLING, DISASSEMBLY / REASSEMBLY & SAFETY INSTRUCTIONS

AR STYLE FIREARMS OWNER'S MANUAL: OPERATION, HANDLING, DISASSEMBLY / REASSEMBLY & SAFETY INSTRUCTIONS AR STYLE FIREARMS OWNER'S MANUAL: OPERATION, HANDLING, DISASSEMBLY / REASSEMBLY & SAFETY INSTRUCTIONS - DO NOT DISCARD THIS MANUAL - READ THIS MANUAL CAREFULLY, PAYING CLOSE ATTENTION TO THE INSTRUCTIONS

More information

K Page 1 of 48 Air Intake - Pg. 17

K Page 1 of 48 Air Intake - Pg. 17 K532-53168 Page 1 of 48 Air Intake - Pg. 17 Ref # Part Number Qty Description 24 25 041 06-S 1 Gasket, elbow 25 48 054 09 1 Elbow, air cleaner Discontinued not available at Kohler Co. 35 277116-S 1 Brace,

More information

REPAIR PART NUMBER NUMBER DESCRIPTION 0137 ELE 0136 ELE 12 VOLT SOLENOID

REPAIR PART NUMBER NUMBER DESCRIPTION 0137 ELE 0136 ELE 12 VOLT SOLENOID PART REPAIR PART NUMBER NUMBER DESCRIPTION 0137 ELE 0136 ELE 12 VOLT SOLENOID 0203 WHL 0250 WHL WHEEL HUB 0251 WHL AXLE 0252 WHL DUST CAPS 0253 WHL TIRE - 210 SP 0204 WHL 0211 WHL TIRE & WHEEL - SP 0250

More information

LIQUIP DRYBREAK COUPLER. API800 Series MAINTENANCE INSTRUCTIONS

LIQUIP DRYBREAK COUPLER. API800 Series MAINTENANCE INSTRUCTIONS LIQUIP DRYBREAK COUPLER API800 Series MAINTENANCE INSTRUCTIONS API LOADING COUPLER TO API RP1004 June 2015 Issue: F M:\Product-Info\API8xx\6-Service-Maintenance\API800 MAINTENANCE INSTRUCTIONS 40183.doc

More information

CHAPTER 2 MAINTENANCE

CHAPTER 2 MAINTENANCE CHAPTER 2 MAINTENANCE This chapter addresses the proper care of the machine gun to ensure its overall effectiveness and efficient functioning. The information includes the gunner's knowledge in disassembly

More information

SERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.

SERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding

More information

OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP75H-10 HYDRAULIC WINCH.

OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP75H-10 HYDRAULIC WINCH. W. W. Patterson Company 3 Riversea Road Pittsburgh, PA 15233 Phone: 800-322-2018 FAX: 412-322-2785 OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP75H-10 HYDRAULIC WINCH. Please fill in the following blanks

More information

Final Assembly Instructions Bikes with Threaded Headsets

Final Assembly Instructions Bikes with Threaded Headsets Final Assembly Instructions Bikes with Threaded Headsets Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our

More information

DM-MARD (English) Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike REAR DERAILLEUR XTR RD-M9100 RD-M9120

DM-MARD (English) Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike REAR DERAILLEUR XTR RD-M9100 RD-M9120 (English) DM-MARD001-00 Dealer's Manual ROAD MTB Trekking City Touring/ Comfort Bike URBAN SPORT E-BIKE REAR DERAILLEUR XTR RD-M9100 RD-M9120 CONTENTS CONTENTS...2 IMPORTANT NOTICE...3 TO ENSURE SAFETY...4

More information

BELT DRIVE INDOOR CYCLING BIKE SF-B1712 USER MANUAL

BELT DRIVE INDOOR CYCLING BIKE SF-B1712 USER MANUAL BELT DRIVE INDOOR CYCLING BIKE SF-B1712 USER MANUAL IMPORTANT! Please retain owner s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN

More information

HP-104 & HP-106 Tapping Machine OPERATIONS MANUAL

HP-104 & HP-106 Tapping Machine OPERATIONS MANUAL 30230 Los Alamos Rd. Murrieta, CA 92563 800-279-5659 FAX 951-926-2334 TappingMachines.com HP-104 & HP-106 Tapping Machine OPERATIONS MANUAL & OPERATING INSTRUCTIONS WARNING READ: Before using this product,

More information

B-Too Drilling and Tapping Machine

B-Too Drilling and Tapping Machine Material Specifications Powered by hand or with Ridgid 690 (TM-29) High strength, modular aluminum and steel components Inserts any 3 /4" to 1" corporation stop under pressure Extracts threaded corporation

More information

VERSA BIKE RACK INSTRUCTIONS

VERSA BIKE RACK INSTRUCTIONS VERSA BIKE RACK INSTRUCTIONS Models #8, 8 Important This rack is designed for use with a or. receiver hitch. The rack is designed to hold a maximum of two bicycles. Do not use it for anything other than

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Model No. Description RP2300FC, RP2301FC Router CONCEPT AND MAIN APPLICATIONS Models RP2300FC and RP2301FC are upgraded sister tools of our current plunge-type electronic router Model

More information

Vac Bagger Wheelhorse 42 and 48 Mowers for Classic Garden Tractors

Vac Bagger Wheelhorse 42 and 48 Mowers for Classic Garden Tractors Form No. -80 Vac Bagger Wheelhorse and 8 Mowers for Classic Garden Tractors Model No. 790 000000 & Up Operator s Manual Domestic English (EN) Contents Page Introduction................................

More information

RADIUS ROD BUSHING SET

RADIUS ROD BUSHING SET RADIUS ROD BUSHING SET These are designed to allow your front suspension to operate much more freely than the factory units, with less maintenaance. STICKSION could be a key word here. The front end will

More information

Liste de pièces Lista de Piezas Parts List

Liste de pièces Lista de Piezas Parts List S Liste de pièces Lista de Piezas Parts List 4 4-14 April 014 1 1 14 1 13 13 17 8 7 1 3 4 11 1 1 0 Singer S Ref No Part No Part Name 1 800400 Front cover (unit) S NA Front cover 3 N/A Button 4 N/A Button

More information

Tripod Setup Guide (M-TPx)

Tripod Setup Guide (M-TPx) Items needed: 1/2 inch wrench, mast level (M-MLA), medium size wire cutters, crescent wrench, all-purpose grease, tape measure, tie wraps, redi-mix cement (optional), shovel (optional), sledge hammer (for

More information

Model 130M Pneumatic Controller

Model 130M Pneumatic Controller Instruction MI 017-450 May 1978 Model 130M Pneumatic Controller Installation and Operation Manual Control Unit Controller Model 130M Controller is a pneumatic, shelf-mounted instrument with a separate

More information

TECHNICAL DATA ZTR Model 312

TECHNICAL DATA ZTR Model 312 DIXON INDUSTRIES. INC. A BLOUNT COMPANY AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYVILLE KS 67337 0945 316 251 2000 FAX 316 251 4117 TECHNICAL DATA ZTR Model 312 IMPORTANT - READ OPERATOR'S MANUAL BEFORE

More information

Final Assembly Instructions Bikes with Threaded Headsets

Final Assembly Instructions Bikes with Threaded Headsets Final Assembly Instructions Bikes with Threaded Headsets Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our

More information

Thank you for purchasing a WIKE BOX BIKE!

Thank you for purchasing a WIKE BOX BIKE! Thank you for purchasing a WIKE BOX BIKE! Contents Safety.....3 Front wheel.4 Kickstand..5 Handle Bar & Box 6 Seat post and Saddle 7 Final pre-ride check 8 Tools needed to assemble Bike: -High table or

More information

Final Assembly Instructions Bikes with Quill Stems

Final Assembly Instructions Bikes with Quill Stems Final Assembly Instructions Bikes with Quill Stems Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert

More information

MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A

MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A OPERATION MANUAL / SPARE PARTS LIST MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A337.0001 13.1912.01 13191201.en/MAS/ 10.02 INDEX PAGE 1 SAFETY INSTRUCTIONS 2 2 WARRANTY CONDITIONS AND LIABILITY 4 3 APPROPRIATE

More information

310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment

310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment OPERATOR S MANUAL FOR MORSE TILT-TO-LOAD DRUM ROTATOR SAFETY INFORMATION: While Morse Manufacturing Co. drum handling equipment is engineered for safety and efficiency, a high degree of responsibility

More information

Assembly Drawing: W-311B-A01, or as applicable Parts List: W-311B-A01-1, or as applicable Special Tools: , , &

Assembly Drawing: W-311B-A01, or as applicable Parts List: W-311B-A01-1, or as applicable Special Tools: , , & REDQ Regulators Model 411B Barstock Design Powreactor Dome Regulator OPERATION AND MAINTENANCE Contents Scope..............................1 Installation..........................1 General Description....................1

More information

SPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1.

SPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1. 2 GALLON TWIN STACK AIR COMPRESSOR Model: 9526 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or

More information

DM-RARD (English) Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike. Rear Derailleur DURA-ACE RD-R9100 ULTEGRA RD-R8000

DM-RARD (English) Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike. Rear Derailleur DURA-ACE RD-R9100 ULTEGRA RD-R8000 (English) DM-RARD001-03 Dealer's Manual ROAD MTB Trekking City Touring/ Comfort Bike URBAN SPORT E-BIKE Rear Derailleur DURA-ACE RD-R9100 ULTEGRA RD-R8000 CONTENTS IMPORTANT NOTICE... 3 TO ENSURE SAFETY...

More information

Barrel Assembly. Field Stripping

Barrel Assembly. Field Stripping WARNINGS: Carry out safety check before handling the weapon. The weapon is heavily oiled for shipping. Clean and lubricate before firing. These procedures given apply only to the US Ordnance QCB version.

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Models No. TD0101, TD0101F Description Impact Driver L PRODUCT P 1/ 14 CONCEPT AND MAIN APPLICATIONS Models TD0101 and TD0101F are cost-competitive 100N.m-class impact driver developed

More information

MAINTENANCE PROCEDURE FOR X 650

MAINTENANCE PROCEDURE FOR X 650 MAINTENANCE PROCEDURE FOR X 650 X 650 25. juli 2005-1/6 MAINTENANCE PROCEDURE FOR X 650 2 ND STAGE WARNING: This maintenance procedure is only for appointed Scubapro technicians that completed a course

More information

TECHNICAL DATA BROCHURE Model 304

TECHNICAL DATA BROCHURE Model 304 DIXON INDUSTRIES, INC. A BLOUNT COMPANY AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYVILLE KS 673370945 316 251 2000 FAX 316 251 4117 TECHNICAL DATA BROCHURE Model 304 IMPORTANT - READ OPERATOR'S MANUAL BEFORE

More information

OPERATION AND FUNCTIONING

OPERATION AND FUNCTIONING C1, FM 23-65 * CHAPTER 3 OPERATION AND FUNCTIONING This chapter explains the operation of the MG. It discusses the loading, unloading, and clearing procedures, and the cycle of functioning of the weapon.

More information

ATV 90 Y-12 YOUTH 2-STROKE RED (A2004ATB2BUSR) Page 1 of 52 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY

ATV 90 Y-12 YOUTH 2-STROKE RED (A2004ATB2BUSR) Page 1 of 52 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY 2004 ATV 90 Y-12 YOUTH 2-STROKE RED (A2004ATB2BUSR) Page 1 of 52 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY 2004 ATV 90 Y-12 YOUTH 2-STROKE RED (A2004ATB2BUSR) Page 2 of 52 A-ARM, FLOOR PANEL, AND BUMPER

More information

Reproduction. Not for 27" & 29" TWO STAGE INTERMEDIATE SNOWTHROWERS Parts Manual for M1227E M1227EX M1529E

Reproduction. Not for 27 & 29 TWO STAGE INTERMEDIATE SNOWTHROWERS Parts Manual for M1227E M1227EX M1529E Parts Manual for 27" & 29" TWO STAGE INTERMEDIATE SNOWTHROWERS 2011 Model No. Description 1696001 M1227E 1696002 M1227EX 1696003 M1529E Briggs & Stratton Yard Power Products Group 535 Macon Road McDonough,

More information

Fontaine Fifth Wheel Ultra LT Rebuild Procedures

Fontaine Fifth Wheel Ultra LT Rebuild Procedures Fontaine Fifth Wheel Ultra LT Rebuild Procedures Disassembly Assembly Adjustments 800-874-9780 2010 LT-147 January 2010 Dissassembly Cover plate removed for clarity. Refer to exploded view of assembly

More information

HOLLISTER-WHITNEY ROPE GRIPPER

HOLLISTER-WHITNEY ROPE GRIPPER HOLLISTER-WHITNEY ROPE GRIPPER Instructions for Model #620GA1, 620GA2 (Patented worldwide, other patents pending) WARNING: KEEP HANDS CLEAR OF ROPE GRIPPER. FORCES CREATED CAN CRUSH FINGERS. Figure 1 ROPE

More information

Maintenance Manual. Note: This document is broken up into the following 6 sections of prescribed maintenance.

Maintenance Manual. Note: This document is broken up into the following 6 sections of prescribed maintenance. How to Perform Maintenance On LPKF Circuit Board Plotters Requirements - LPKF Circuit Board Plotter - BoardMaster Software - 2.5 mm Allen wrench (for earlier model machines) - 3mm Allen Wrench - 4mm Allen

More information

HATFIELD. Continuing the Tradition SEMI-AUTOMATIC SHOTGUN INSTRUCTION MANUAL

HATFIELD. Continuing the Tradition SEMI-AUTOMATIC SHOTGUN INSTRUCTION MANUAL HATFIELD Continuing the Tradition SEMI-AUTOMATIC SHOTGUN INSTRUCTION MANUAL READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM SAFETY HANDLING RULES 1.Always keep the

More information

LIST NO.E078 ENGINE. ENGINE BRUSH CUTTER Model CG 27EAS (E1)

LIST NO.E078 ENGINE. ENGINE BRUSH CUTTER Model CG 27EAS (E1) LIST E078 (E1) ENGINE ENGINE BRUSH CUTTER Model 2010 7 16 A B 1 2 1 3 4 5 6 7 16 15 17 13 8 9 10 11 12 13 14 15 18 19 20 11 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

More information

M16 R / M1600 R USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM.

M16 R / M1600 R USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM. ARMSCOR M16 R / M1600 R USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM. DISCHARGING FIREARMS IN POOLY VENTILATED AREAS, CLEANING

More information

48 Mower Wheel Horse 5xi Garden Tractor Attachment

48 Mower Wheel Horse 5xi Garden Tractor Attachment Form No. 6-565 8 Mower Wheel Horse 5xi Garden Tractor Attachment Model No. 786 Serial No. 000000 and Up Model No. 786 Serial No. 000000 and Up Operator s Manual Domestic English (EN) Contents Page Introduction................................

More information

DM-MBRD (English) Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike. Rear Derailleur SLX RD-M7000 DEORE RD-M6000

DM-MBRD (English) Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike. Rear Derailleur SLX RD-M7000 DEORE RD-M6000 (English) DM-MBRD001-04 Dealer's Manual ROAD MTB Trekking City Touring/ Comfort Bike URBAN SPORT E-BIKE Rear Derailleur SLX RD-M7000 DEORE RD-M6000 CONTENTS IMPORTANT NOTICE... 3 TO ENSURE SAFETY... 4

More information

Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project.

Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project. Greg Cowens' $10 PVC Roller Reefing for CP-16's by Greg Cowen Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project. Materials: 2

More information

QUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift

QUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your

More information

1.0 - OPENING AND CLOSING THE DOOR

1.0 - OPENING AND CLOSING THE DOOR The purpose of this manual is to provide the user with instructions on how to safely open and close, how to conduct routine maintenance, and how to install the PEI TWINLOCK Closure on a pressure vessel.

More information

Important! Read this manual before using the reel. Manual english

Important! Read this manual before using the reel. Manual english mportant! Read this manual before using the reel. Manual english F3W, L5W and H5D series Spool Change System This fly fishing reels are equipped with a spool change system wherein the spool is the only

More information

Tru Trak Sulky Proline Mid Size Mower Attachment

Tru Trak Sulky Proline Mid Size Mower Attachment Form No. -7 Tru Trak Sulky Proline Mid Size Mower Attachment Model No. 00 000000 and Up Operator s Manual Domestic English (EN) Contents Page Introduction................................ Safety.....................................

More information

Rear Drive System SERVICE INSTRUCTION. Specifications SI-R670B

Rear Drive System SERVICE INSTRUCTION. Specifications SI-R670B - SERVICE INSTRUCTION SI-R670B t Rear Drive System Before use, read these instructions carefully, and follow them for correct use. In order to realize the best performance, we recommend that the following

More information

Front derailleur. Dealer's Manual DURA-ACE FD-R9100 ULTEGRA FD-R FD ROAD MTB Trekking. City Touring/ Comfort Bike DM-RAFD001-03

Front derailleur. Dealer's Manual DURA-ACE FD-R9100 ULTEGRA FD-R FD ROAD MTB Trekking. City Touring/ Comfort Bike DM-RAFD001-03 (English) DM-RAFD001-03 Dealer's Manual ROAD MTB Trekking City Touring/ Comfort Bike URBAN SPORT E-BIKE Front derailleur DURA-ACE FD-R9100 ULTEGRA FD-R8000 105 FD-5801 Procedures for cable tension adjustment

More information

2019 MADONE ASSEMBLY MANUAL

2019 MADONE ASSEMBLY MANUAL 2019 MADONE ASSEMBLY MANUAL 2019 MADONE Rim brakes and Di2 drivetrain Rim brakes and mechanical drivetrain Disc brakes and Di2 drivetrain Disc brakes and mechanical drivetrain TABLE OF CONTENTS Common

More information

ELECTRIC TOOL PARTS LIST

ELECTRIC TOOL PARTS LIST Hitachi Power Tools LIST E933 ELECTRIC TOOL PARTS LIST SLIDE COMPOUND SAW Model 2004 2 13 (E2) 1 2 3 4 5 6 7 40 41 601 8 9 10 11 12 26 27 28 29 30 29 602 618 602 10 9 42 603 604 605 606 607 608 14 43 13

More information

LIQUIP DRYBREAK COUPLER. LYNX Series MAINTENANCE INSTRUCTIONS

LIQUIP DRYBREAK COUPLER. LYNX Series MAINTENANCE INSTRUCTIONS LIQUIP DRYBREAK COUPLER LYNX Series MAINTENANCE INSTRUCTIONS API LOADING COUPLER TO API RP1004 February 2016 Issue: DRAFT A Issue: DRAFT - A 02/01/16 Page 1 CONTENTS LYNX Series Datasheet... 3 LYNX Series

More information

Bladerider X8 Assembly Help Notes

Bladerider X8 Assembly Help Notes 2.1 Remove All Parts & Have Some Tools Handy Remove all items from the box and identify each part as per the packing sheet and check that nothing is missing. If there is something missing, please email

More information

I.H.S INSTALLATION INSTRUCTIONS

I.H.S INSTALLATION INSTRUCTIONS I.H.S INSTALLATION INSTRUCTIONS TOOLS REQUIRED The following tools will be required for installation of your I.H.S. system. Item Qty Needed 9/16 Open End Wrench 2 3/4 Open End Wrench 1 1/2 Open End Wrench

More information

Repair instructions. Pivot bushing replacement. XL-AS10001RM-en-DE Rev B

Repair instructions. Pivot bushing replacement. XL-AS10001RM-en-DE Rev B Repair instructions Pivot bushing replacement XL-AS10001RM-en-DE Rev B Table of contents Table of contents 1 General information... 3 1.1 Safety information...3 1.2 Legal information...4 1.3 Order and

More information

Pressure Dump Valve Service Kit for Series 2300 Units

Pressure Dump Valve Service Kit for Series 2300 Units Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit

More information

Columbia Taping Tools. Hydra Reach Handle. Manual

Columbia Taping Tools. Hydra Reach Handle. Manual Columbia Taping Tools Hydra Reach Handle Manual Table of contents Warning 2 Introduction 3 Before you start, identify your handle 4 What is your problem? 5 Reservoir Upgrade 5 Setting up the loading system

More information

Installation Instructions

Installation Instructions 116-3027, 116-3017 X-Pando Adjustable Steel Protector Installation Instructions 1404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 NB 6/28/10 607-0112 Step 1. Mounting

More information

A. TO PREPARE THE MACHINE FOR USE.

A. TO PREPARE THE MACHINE FOR USE. INSTRUCTION MANUAL FOR THE ML120 STRINGING MACHINE. CONTENTS: A. TO PREPARE THE MACHINE FOR USE. 1. The assembly of frame with console and tooltray. 2. Fixing the lever of the tension unit. 3. Putting

More information

Exchange Part# 2018 List Price

Exchange Part# 2018 List Price List 22581-1 AIR GUN ASSY ONLY -TORQUE RITE POWER DRA $762 22581-1R $451 N/A 310-120 AIR VALVE, 3 WAY $127 N/A N/A N/A 16806-M BALLSCREW ASS'Y, Z-AXIS $1,660 N/A N/A N/A 15609-16 BALLSCREW MX 16" ENGLISH

More information

OPERATOR S MANUAL SPREADER. CSS, VNQ [For Combine Harvester AW82V] Original instructions

OPERATOR S MANUAL SPREADER. CSS, VNQ [For Combine Harvester AW82V] Original instructions OPERATOR S MANUAL SPREADER CSS, VNQ [For Combine Harvester AW82V] en Original instructions Introduction Introduction Please read this operator s manual before using your spreader. We would first like to

More information

LJ1-25 LouieJRtm Tapping Machine

LJ1-25 LouieJRtm Tapping Machine 1/21/08 WARNING: Before using this product, read owners manual and follow all Safety Rules and Operating Instructions. LJ1-25 LouieJRtm Tapping Machine OPERATIONS MANUAL & OPERATING INSTRUCTIONS 30230

More information

MUELLER A A Non-Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3.

MUELLER A A Non-Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3. Installation Instructions manual MUELLER table of contents PAGE A-20808 General Information 2 Technical Data 3 Dimensions 4 A-20809 Non-Adjustable Installation 5-6 Parts 7 Maintenance 8 Vertical Indicator

More information

Lock-N-Load. Bullet Feeder

Lock-N-Load. Bullet Feeder Lock-N-Load Bullet Feeder table of contents steps Overview... 2 List of required hand tools... 2 1: Mounting the Bullet Feeder to the Bench... 3 2: Mounting the Bullet Feed Hopper... 4 3: Bullet Feed Hopper

More information

600 / 600FC OWNER'S MANUAL

600 / 600FC OWNER'S MANUAL PROGRESSION 600 / 600FC OWNER'S MANUAL Issue 2 / Version E - Dec. 10, 1997 Copyright 1997 GAMMA Sports - All Rights Reserved PROGRESSION 600 / 600FC OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY

More information

Installation Instructions for the AlphaDeck Staging System

Installation Instructions for the AlphaDeck Staging System Installation Instructions for the AlphaDeck Staging System Step 1 - Preparation A. Before setting up this system, determine the location of the stages and all the parts you will need. B. Read through the

More information

Drive Belt Instructions

Drive Belt Instructions Drive Belt Safety Do not roll, pry, twist, invert or bend the belt back on itself. Do not zip tie the belt. The acceptable temperature range for your belt drive is -53 C to 85 C. Do not lubricate the belt

More information

DM-RD (English) Dealer s Manual. ROAD Rear Derailleur RD-9000 RD-6800 RD-5800 RD-4700

DM-RD (English) Dealer s Manual. ROAD Rear Derailleur RD-9000 RD-6800 RD-5800 RD-4700 (English) DM-RD0003-09 ROAD Rear Derailleur Dealer s Manual RD-9000 RD-6800 RD-5800 RD-4700 CONTENTS IMPORTANT NOTICE...3 TO ENSURE SAFETY...4 LIST OF TOOLS TO BE USED...6 INSTALLATION...8 Chain length...

More information

BELT DRIVE INDOOR CYCLING BIKE SF-B1712

BELT DRIVE INDOOR CYCLING BIKE SF-B1712 BELT DRIVE INDOOR CYCLING BIKE SF-B1712 USER MANUAL IMPORTANT! Read all instructions carefully before using this product. Retain owner s manual for future reference. For customer service, please contact:

More information

MUELLER. A A Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3.

MUELLER. A A Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3. Installation Instructions manual MUELLER table of contents PAGE A-20806 A-20807 Adjustable General Information 2 Technical Data 3 Dimensions 4 Installation 5-6 Parts 7 Maintenance 8 Vertical Indicator

More information

SAFETY RULES WARNING: READ THESE SAFETY RULES & OPERATORS MANUAL BEFORE HANDLING YOUR FIREARM

SAFETY RULES WARNING: READ THESE SAFETY RULES & OPERATORS MANUAL BEFORE HANDLING YOUR FIREARM SAFETY RULES WARNING: READ THESE SAFETY RULES & OPERATORS MANUAL BEFORE HANDLING YOUR FIREARM Never point a firearm at anyone and always keep the muzzle pointed in a safe direction. Always treat all firearms

More information

I Illustrated Parts List 650 CRT B. Tiller. Repair Parts Manual

I Illustrated Parts List 650 CRT B. Tiller. Repair Parts Manual Illustrated Parts List 2001-11 I0102042 650 CRT B 954328030 Repair Parts Manual Tiller HANDLE ASSEMBLY 1 532 18 06-34 Control, Throttle 2 532 00 92-66 Grip, Handle 4 532 15 92-28 Bar Assembly, Control

More information

FLEXIBLE SHAFTING (Wet & Dry)

FLEXIBLE SHAFTING (Wet & Dry) TM-5 April 5, 2004 Elliott offers a complete line of precision tube tools, including: tube expanders Boiler Expanders Heat Exchanger Expanders Condenser Expanders Refinery Expanders tube rolling motors

More information

TECHNICAL DATA BROCHURE - ZTR 428 & 429

TECHNICAL DATA BROCHURE - ZTR 428 & 429 TECHNICAL DATA BROCHURE - ZTR 428 & 429 DATE 8/89 (Rev.) MPORTANT -- READ OPERATOR S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS. Deluxe Seat Adjustment Easy hand lever action allows forward and backward

More information

USER MANUAL

USER MANUAL C Cimarron Sports 1-888-816-6517 www.cimarronsports.com Combo Pitching Machine USER MANUAL TABLE OF CONTENTS Thank you for purchasing the Cimarron Combo Pitching Machine. The Cimarron Combo Pitching Machine

More information