Fatigue Resistant Sockets for Dynamic Loads PFEIFER Cable Structures. Cable structures technology Info Nr PFEIFER SEIL- UND HEBETECHNIK GMBH

Size: px
Start display at page:

Download "Fatigue Resistant Sockets for Dynamic Loads PFEIFER Cable Structures. Cable structures technology Info Nr PFEIFER SEIL- UND HEBETECHNIK GMBH"

Transcription

1 Fatigue Resistant Sockets for Dynamic Loads Cable Structures Cable structures technology Info Nr SEIL- UND HEBETECHNIK GMBH DR.-KARL-LENZ-STRASSE 66 D MEMMINGEN TELEPHONE +49 (0) TELEFAX +49 (0) cablestructures@pfeifer.de INTERNET

2 In this information paper presents its two new open spelter sockets type 700 and type 710 In 1999 Seil- und Hebetechnik GmbH, as the first manufacturer on the market, obtained national technical approvals for its cable tension members. They were specifically designed for predominantly static loads. Therefore they are perfectly suitable for pedestrian bridges, stadium roofs, other wide span structures and zoological gardens. Recently achieved the European technical approval for this product line (ETA -11/0160). It is available as a free download on our web site Besides the mentioned applications the cables are also included in structures, such as road bridges or other structures which are dynamically loaded. Numerous fatigue tests have shown that an open spelter socket that is economically designed for static loads is only suitable to Figure 1: Open spelter socket Type 700 Requirement class according to EN paragraph 2: Fatigue load Corrosive load, not exposed to the outside environment Corrosive load, exposed to the outside environment a limited extent for dynamic loads. However, usage within road bridges and other structures under cyclic loads requires materials with specific characteristics. These characteristics are fulfilled by the cables, but not to the full extent with our open spelter sockets type 802. For this reason designed a new open spelter socket, which we would like to present to you now: The new open spelter sockets type 700 and type 710 The new open spelter socket type 700 represents a one-piece socket with a fixed forked cable connection. The force in the cable is transferred through a movable pin to the steel structure. A bolted lid prevents the pin from falling out. This type is perfectly suitable for applications with periodically occurring loads, which do not require length adjustment. No significant fatigue load Class 1 Class 2 Fatigue load mainly caused by longitudinal forces Fatigue load caused by longitudinal forces and bending (wind and rain) Class 3 Class 4 Class 5 Open spelter sockets type 802 fulfil the requirements of the classes 1 and 2. Open spelter sockets type 700 now fulfil all requirement classes 1 to 5. Thus, the fatigue loads are also covered. 2

3 Open spelter sockets type 710 consist of a conical socket with internal thread type 800, a threaded rod with right-hand and left-hand thread and a forked connector with internal thread. This type is used where length adjustment of the cable tension member is necessary. When dimensioning the connection in the steel structure it has to be considered that the dimensions of the plate thickness must be in accordance with the specifications. If there are no exact values given the notch class classification from table 8.1 (13) DIN EN can be used for the calculation. Apart from the end fittings type 700 and type 710 there are several other sockets from the range of products, which are suitable for dynamic loads. For an anchorage of cable tension members with adjustable length we provide the proven and tested cylindrical socket type 810 with spherical nut and spherical disc type 813 / 814. This combination fulfils all demands on cable tension members when they are exposed to dynamic loads. Figure 2: Adjustable open spelter socket type 710 Requirement classes according to EN paragraph 2: Fatigue load Corrosive load, not exposed to the outside environment Corrosive load, exposed to the outside environment No significant fatigue load Class 1 Class 2 Fatigue load mainly caused by longitudinal forces Fatigue load caused by longitudinal forces and bending (wind and rain) Class 3 Class 4 Class 5 Open spelter sockets type 710 fulfil the requirements of the classes 1 to 4. The fork connector of the type 710 corresponds to the geometry of the socket type 700. The two types 700 and 710 thus fit together well. The sophisticated shape of these connections follows our corporate design of the product families PG and PE used for Cable tension members. Thus, the cable types PV (PV = fully locked cable) and other Pfeifer cable types can be arranged side by side in a building following one lead design intent. Figure 3: Cylindrical socket type 810 with spherical nut and disc type 813 / 814 Design and calculation criteria: Structural analysis: The structural analysis and verification of the open spelter sockets is, as far as possible, performed according to DIN / DIN EN In accordance with this standard the socket, the connection sheet, the fork and the pin are verified. Fatigue analysis: The calculation of the dynamically stressed cable tension members is based on the standard DIN EN , part 9 and part 11. In accordance with this standard, full locked cables and spiral strands with poured anchorings with metal and resin fillings are allocated to a notch class category with the reference value of =150 N/mm² (DIN EN table 9.1). This reference value specifies the fatigue strength for 2 million load cycles and a maximum force of 0.45 x Z Bk (Z Bk = characteristic breaking force of the cable). 3

4 Fatigue tests are performed according to EN paragraph A.4.1 with a stress cycle of σ =1.25 x The standard DIN EN table 3.1 recommends safety factors for the fatigue strength (γ Mf ). If, for instance, the design concept safety against fatigue failure without notice is chosen for the cable tension member and the resulting damage is chosen as high, then the resulting γ Mf -factor is Therefore the limiting value of the stress range for the cable tension member is / γ Mf = 150 N/mm² / 1.35 = 111 N/mm² The engineer has to calculate the damage equivalent constant stress range for the respective cable tension member. The reference value is 2 million load cycles ( σ E,2 ) This value has to be determined according to DIN EN paragraph 6. The design value results from the multiplication of σ E,2 with the safety factor γ Ff for the damage equivalent stress range. The fatigue verification is fulfilled if the design value is smaller than or equal to the limiting value. Fatigue verification according to DIN EN paragraph 8: γ Ff * σ E,2 / γ Mf Illustration of the dependence of the stress cycles N from the longitudinal stress range (Wöhler curve from EN (9.2)): In the example illustrated the curve for a cable tension member with the notch class classification of = 150 N/mm² is shown. As explained above, this reference value is valid for 2 million stress cycles with a maximum force of 0.45 x Z Bk. In accordance with EN paragraph 9.2, for the inclination of the fatigue strength curve the value of m=4 can be assumed for N 2 x 10 6 and the value of m = 6 for N > 2 x It is therefore possible to read the anticipated fatigue life as a function of the longitudinal stress range from the diagram. Equation for the determination of the bearable stress range σ z : With N c = 2 x 10 6 = 150 N/mm² N z = number of load cycles m = 4 up to 2 x 10 6 load cycles and m = 6 above 2 x 10 6 load cycles Equation for the determination of the number of bearable load cycles N z : With N c = 2 x 10 6 = 150 N/mm² ( Δσ Z := m Δσ m C Δσ N C Z :=N C ( Δσ Z ( N C N Z σ z = stress range m = 4 up to 2 x 10 6 load cycles and m = 6 above 2 x 10 6 load cycles m ( 4

5 FEM calculation: The sockets type 700 and 710 were constructed in CAD programmes in 3D. These drafts served as a basis for the subsequent FEM calculations. Several optimising steps lead to the present design. Symbols used (in accordance with EN ) σ = stress range (longitudinal stresses) σ C = reference value for fatigue strength with N c = 2 x 10 6 Load cycle σ E = damage equivalent constant stress range related to n max γ Mf = γ factor for the fatigue strength γ Ff = γ factor for the damage equivalent stress range σ E Figure 4: FEM calculation of open spelter socket The aim of the analysis was to develop cable tension members which are suitable for dynamic stress (for example road bridges) have an aesthetically pleasing shape can be produced efficiently. These demands are entirely fulfilled with the new types 700 and

6 08.12.pdf WA

List of Material Rope Courses FLEXIBLE PFEIFER SEIL- UND HEBETECHNIK GMBH

List of Material Rope Courses FLEXIBLE PFEIFER SEIL- UND HEBETECHNIK GMBH 09/2014 R O T FLEXILE S U SEIL- UND HEETECHNIK GMH List of Material Rope Courses DR.-KARL-LENZ-STRASSE 66 D-87700 MEMMINGEN TELEPHONE +49 (0) 83 31-937-267 TELEFAX +49 (0) 83 31-937-341 E-MAIL wireropes@pfeifer.de

More information

The Powerful Sealing Calculation

The Powerful Sealing Calculation KLINGER expert 6.0 The Powerful Sealing Calculation The KLINGER expert 6.0 gasket design program is a versatile software to assist users in the selection of non-metallic gasket materials. www.klinger.co.at

More information

Load Ring bolted > VWBG < in pink

Load Ring bolted > VWBG < in pink RUD-Art.-Nr.: 8503693-EN / 03.014 Load Ring bolted > VWBG < in pink EN Safety instructions This safety instruction/declaration has to be kept on file for the whole lifetime of the product. Translation

More information

Also suitable for: Concrete C12/15. For fixing of: Steel constructions Railings Consoles Ladders Wooden constructions Cable trays Machines Staircases

Also suitable for: Concrete C12/15. For fixing of: Steel constructions Railings Consoles Ladders Wooden constructions Cable trays Machines Staircases 28 Highbond anchor FHB II Flexible installation and highest loads in the cracked tensile zone. OVERVIEW FHB II-A S (standard), zinc plated steel FHB II-A L (performance optimised), zinc-plated steel Resin

More information

OPENINGS AND REINFORCEMENTS 26

OPENINGS AND REINFORCEMENTS 26 ASME BPVC.VIII.1-2015 UG-35.2 UG-36 (4) It is recognized that it is impractical to write requirements to cover the multiplicity of devices used for quick access, or to prevent negligent operation or the

More information

Rope measurement devices program PFEIFER SEIL- UND HEBETECHNIK GMBH

Rope measurement devices program PFEIFER SEIL- UND HEBETECHNIK GMBH 02/2015 SEIL- UND HEBETECHNIK GMBH Rope measurement devices program DR.-KARL-LENZ-STRASSE 66 D-87700 MEMMINGEN TELEPHONE +49 (0) 83 31-937-267 TELEFAX +49 (0) 83 31-937-341 E-MAIL wireropes@pfeifer.de

More information

EEF. Fatigue Testing Unit PROCESS DIAGRAM AND UNIT ELEMENTS ALLOCATION. Engineering and Technical Teaching Equipment

EEF. Fatigue Testing Unit PROCESS DIAGRAM AND UNIT ELEMENTS ALLOCATION. Engineering and Technical Teaching Equipment Engineering and Technical Teaching Equipment Fatigue Testing Unit EEF PROCESS DIAGRAM AND UNIT ELEMENTS ALLOCATION ISO 9001: Quality Management (for Design, Manufacturing, Commercialization and After-sales

More information

Bulk materials handling equipment PFEIFER SEIL- UND HEBETECHNIK GMBH

Bulk materials handling equipment PFEIFER SEIL- UND HEBETECHNIK GMBH 06/2017 SEIL- UND HEBETECHNIK GMBH Bulk materials handling equipment DR.-KARL-LENZ-STRASSE 66 D-87700 MEMMINGEN TELEPHONE +49 (0) 83 31-937-301 TELEFAX +49 (0) 83 31-937-341 E-MAIL wireropes@pfeifer.de

More information

The Use of BS 5400: Part 10: Code of Practice for Fatigue

The Use of BS 5400: Part 10: Code of Practice for Fatigue THE HIGHWAYS AGENCY THE SCOTTISH OFFICE DEVELOPMENT DEPARTMENT Amendment No. 1, dated November 1983 THE WELSH OFFICE Y SWYDDFA GYMREIG THE DEPARTMENT OF THE ENVIRONMENT FOR NORTHERN IRELAND The Use of

More information

3.1 T AND TKH FERRULES EUROPEAN STANDARD SYSTEM EN

3.1 T AND TKH FERRULES EUROPEAN STANDARD SYSTEM EN TURNBACK FERRULES T ferrule TKH ferrule 3.1 T AND TKH FERRULES EUROPEAN STANDARD SYSTEM EN 134113 GENERAL DESCRIPTION The aluminium ferrules, type T and type TKH correspond to the European standard for

More information

Liquefied gas cargo tanks and process pressure vessels

Liquefied gas cargo tanks and process pressure vessels .1 -.3 Liquefied gas cargo tanks and process pressure vessels.1 General.1.1 The present texts give the general principles which are applied by Classification Societies for approval and survey of the relevant

More information

Corrugated Hose Loop Calculations

Corrugated Hose Loop Calculations Corrugated Hose Loop Calculations The loop installation is one of the most common application for metal hoses. It allows the flexible hose assembly to work properly. Care must always be exercised to ensure

More information

Simulating the effect of wire rope safety clamps on rope terminations

Simulating the effect of wire rope safety clamps on rope terminations Simulating the effect of wire rope safety clamps on rope terminations Simulating the effect of wire rope safety clamps on ropeterminations by I.M.L. Ridge, J.M. Teissier and R. Verreet Content 1. Background...4

More information

fischer Epoxy Mortar FIS EB The basic epoxy mortar for applications in concrete

fischer Epoxy Mortar FIS EB The basic epoxy mortar for applications in concrete fischer Epoxy Mortar FIS EB The basic epoxy mortar for applications in concrete For standard applications in concrete and rebar connections. Advantages at a glance Epoxy mortar for applications in concrete

More information

MAE 322 Machine Design Lecture 5 Fatigue - 2. Dr. Hodge Jenkins Mercer University

MAE 322 Machine Design Lecture 5 Fatigue - 2. Dr. Hodge Jenkins Mercer University MAE 322 Machine Design Lecture 5 Fatigue - 2 Dr. Hodge Jenkins Mercer University Returning to Stress-Life Fatigue Modeling Fatigue Stress-Life: S f -N Diagram for steels Stress levels below S e (Endurance

More information

Mechanical Anchoring Systems HDA Undercut Anchor Product description. HDA-P Undercut Anchor Pre-Set Type

Mechanical Anchoring Systems HDA Undercut Anchor Product description. HDA-P Undercut Anchor Pre-Set Type Mechanical Anchoring Systems 3.3 3.3.1 HDA Undercut Anchor 3.3.1.1 Product description The Hilti HDA undercut anchor is a heavy-duty mechanical anchor with carbide-tipped undercut segments used to perform

More information

ISO INTERNATIONAL STANDARD. Steel wire ropes for the petroleum and natural gas industries Minimum requirements and terms of acceptance

ISO INTERNATIONAL STANDARD. Steel wire ropes for the petroleum and natural gas industries Minimum requirements and terms of acceptance INTERNATIONAL STANDARD ISO 10425 First edition 2003-08-15 Steel wire ropes for the petroleum and natural gas industries Minimum requirements and terms of acceptance Câbles en acier pour les industries

More information

Rope application technology combined expertise PFEIFER SEIL- UND HEBETECHNIK GMBH

Rope application technology combined expertise PFEIFER SEIL- UND HEBETECHNIK GMBH 10/2017 SEIL- UND HEBETECHNIK GMBH Rope application technology combined expertise DR.-KARL-LENZ-STRASSE 66 DE-87700 MEMMINGEN PHONE +49 (0) 83 31-937-301 FAX +49 (0) 83 31-937-123 E-MAIL wirerope@pfeifer.de

More information

2.1 Introduction to pressure vessels

2.1 Introduction to pressure vessels 2.1 Introduction to pressure vessels Pressure vessels in the form of cylinders and tanks are used for storing variety of liquids and gasses at different temperatures and pressures. Some of the substances

More information

INTERPRETATION OF THE REGULATIONS/STANDARDS...

INTERPRETATION OF THE REGULATIONS/STANDARDS... UT Examination of Gas Cylinders (Validation of testing the cylinder base) Table of Contents 1. INTRODUCTION... 1 1.1. GAS CYLINDER MANUFACTURE... 1 1.2. USE OF GAS CYLINDERS... 2 2. INTERPRETATION OF THE

More information

Overview (key points)

Overview (key points) Topic / Subject TYPE 1 FALL-ARREST DEVICES Time frame = mins Contact statement (gain student attention and create a readiness to learn) Overview (key points) Purpose -Fall-arrest devices are designed to

More information

ASSEMBLY INSTRUCTIONS S O L O N STANDARD MODULES

ASSEMBLY INSTRUCTIONS S O L O N STANDARD MODULES ASSEMBLY INSTRUCTIONS S O L O N STANDARD MODULES SOLON Blue 230/07 SOLON Black 230/07 (01, 02) SOLON Blue 220/03 (01, 07) SOLON Black 280/10 SOLON Black 300/10 SOLON P220/6+/07 SOLON M230/6+/07 (01) SOLON

More information

The cost-efficient fixing for flexible use in non-cracked concrete VERSIONS. zinc-plated steel stainless steel hot-dip galvanised steel

The cost-efficient fixing for flexible use in non-cracked concrete VERSIONS. zinc-plated steel stainless steel hot-dip galvanised steel The cost-efficient fixing for flexible use in non-cracked concrete VERSIONS APPROVALS zinc-plated steel stainless steel hot-dip galvanised steel BUILDING MATERIALS Approved for: Concrete C20/25 to C50/60,

More information

Assembly, Installation and operating. instructions for. Söll-Xenon anchorage device

Assembly, Installation and operating. instructions for. Söll-Xenon anchorage device Assembly, Installation and operating instructions for Söll-Xenon anchorage device according to EN 795:1996 Part No: XE-... (The following must be completed by the operator in permanent waterproof ink.)

More information

Related Elevator Products

Related Elevator Products 37 SECTION 2 - Elevator Products Reeving Splices Related Elevator Products Reeving Splice Specifications PIN # Wire Rope Size Units per Carton Wt. per Carton (Lbs) Length (IN) Color Code 1119100012 3/8

More information

ISO INTERNATIONAL STANDARD. Cranes and lifting appliances Selection of wire ropes Part 1: General

ISO INTERNATIONAL STANDARD. Cranes and lifting appliances Selection of wire ropes Part 1: General INTERNATIONAL STANDARD ISO 4308-1 Third edition 2003-05-01 Cranes and lifting appliances Selection of wire ropes Part 1: General Grues et appareils de levage Choix des câbles Partie 1: Généralités Reference

More information

TECHNICAL SPECIFICATION

TECHNICAL SPECIFICATION lifting anchor system The T-slot The T-slot lifting anchor system...1 Introduction...2 The T-slot anchor...3 The O-anchor...3 The P-anchor...3 The TKS rod-anchor...3 The TPA plate-anchor...3 The TKA tilting

More information

Technical Briefing Note

Technical Briefing Note Technical Briefing Note Subject Date Issued Revision Glossary of Terms 14th Nov 2017 Rev 3 The purpose of this Technical Briefing Note is to provide a glossary of terms commonly used in fall injury prevention

More information

fischer Epoxy Mortar FIS EB

fischer Epoxy Mortar FIS EB fischer Epoxy Mortar FIS EB The basic epoxy mortar for applications in concrete ETA-15/0771 ETAG 001-5 Post-installed rebar connection (TR2 fischer Epoxy Mortar FIS EB: For standard applications in concrete

More information

Design and Analysis of Pressure Safety Release Valve by using Finite Element Analysis

Design and Analysis of Pressure Safety Release Valve by using Finite Element Analysis Design and Analysis of Pressure Safety Release Valve by using Finite Element Analysis Mr.V.D.Rathod* 1, Prof.G.A.Kadam* 2, Mr.V. G. Patil* 3 * 1 M.E. Design (Pursuing), SKN Sinhgad Institute of Technology&

More information

Steam Trap BK 15 (DN40, DN 50) Original Installation Instructions English

Steam Trap BK 15 (DN40, DN 50) Original Installation Instructions English Steam Trap BK 15 (DN40, DN 50) EN English Original Installation Instructions 810682-03 1 Contents Page Important Notes Usage for the intended purpose... 4 Safety note... 4 Danger... 4 Attention... 4 Application

More information

Vessels subject to External Pressure

Vessels subject to External Pressure Basic principles of compressive force Vessels subject to External Pressure Before After The result of just air pressure! Presented by: Ray Delaforce Basic principles of compressive force Consider For a

More information

D 042 D 062 In-line mounting Operating pressure up to 100 bar Nominal flow rate up to 90 l/min

D 042 D 062 In-line mounting Operating pressure up to 100 bar Nominal flow rate up to 90 l/min Pressure Filters D D 6 In-line mounting Operating pressure up to 1 bar Nominal flow rate up to 9 l/min Description Application In the pressure circuits of hydraulic and lubrication systems. Performance

More information

Injection mortar FIS VL

Injection mortar FIS VL Injection mortar FIS VL The solid injection mortar for standard applications in cracked concrete and masonry High-bay warehouses BUILDING MATERIALS Approved for anchorings in: Concrete C20/25 to C50/60,

More information

Electropneumatic Positioner and Pneumatic Positioner Type 3760 JIS

Electropneumatic Positioner and Pneumatic Positioner Type 3760 JIS Electropneumatic Positioner and Pneumatic Positioner Type 3760 Application Single-acting positioners for direct attachment to pneumatic control valves. Supplied with an electric input signal of 4 to 20

More information

Combined Wave and Wind Fatigue Damage for Offshore Structures

Combined Wave and Wind Fatigue Damage for Offshore Structures Combined Wave and Wind Fatigue Damage for Offshore Structures Ronald Horn, S.M.I.L.E.-FEM GmbH, Heikendorf Hongxia Gu, IMPaC Offshore Engineering GmbH, Hamburg October, 19-21 th, 2011, Stuttgart 1 S.M.I.L.E.-FEM

More information

Tresca s or Mises Yield Condition in Pressure Vessel Design

Tresca s or Mises Yield Condition in Pressure Vessel Design Tresca s or Mises Yield Condition in Pressure Vessel Design Franz Rauscher Institute for Pressure Vessels and Plant Technology Vienna University of Technology Austria Why using Tresca s yield condition

More information

Push-in fittings CRQS, stainless steel

Push-in fittings CRQS, stainless steel Features Application Effortless selection of the right fitting. Festo offers a secure solution for every connection. The convenient push-in fitting system includes well over 1000 types of standard and

More information

markilux markilux Technical Information safe timeless beautiful markilux Collection Specification markilux 1700 markilux 1700 stretch markilux

markilux markilux Technical Information safe timeless beautiful markilux Collection Specification markilux 1700 markilux 1700 stretch markilux safe timeless beautiful pergola 215 Installation of and awning systems (in line EN 13561) and pergola systems intended for outdoor use meet the requirements of European Standard EN 13561 for blinds and

More information

Evaluation of Eurocode damage equivalent factor based on traffic simulation

Evaluation of Eurocode damage equivalent factor based on traffic simulation Evaluation of Eurocode damage equivalent factor based on traffic simulation N. Maddah & A. Nussbaumer EPFL, Lausanne, Switzerland ABSTRACT: The Eurocodes provide a simplified fatigue design control through

More information

GEA FOR ADVANCED STRUCTURAL DYNAMIC ANALYSIS

GEA FOR ADVANCED STRUCTURAL DYNAMIC ANALYSIS SMART SOLUTIONS FOR VIBRATION MONITORING GEA FOR ADVANCED STRUCTURAL DYNAMIC ANALYSIS ANALYSIS OF CIVIL STRUCTURES - EXPO MERLATA PEDESTRIAN BRIDGE ABSTRACT Civil structures and in particular bridges and

More information

Supratec Gesellschaft für Umweltund Verfahrenstechnik mbh OXYFLEX - M T / M T M E M B R A N E D I S C D I F F U S ER AERATION TECHNOLOGY

Supratec Gesellschaft für Umweltund Verfahrenstechnik mbh OXYFLEX - M T / M T M E M B R A N E D I S C D I F F U S ER AERATION TECHNOLOGY OXYFLEX - M T 2 3 5 / M T 3 0 0 M E M B R A N E D I S C D I F F U S ER UND GESELLSCHAFT FÜR UMWELT- VERFAHRENSTECHNIK MBH AERATION TECHNOLOGY von-drais-straße 7 D-55469 Simmern / Hunsrück Tel.: +49 6761

More information

Z5160 Load adapter Mounting instructions (1.2 EN)

Z5160 Load adapter Mounting instructions (1.2 EN) Z560 Load adapter Mounting instructions (. EN) WARNING! CAUTION! IMPORTANT! Note: References in the manual This refers to a potentially dangerous situation which may lead to personal injury. This refers

More information

TECHNICAL MANUAL. COPRA Anchoring Coupler. For Smart Bolted Connections

TECHNICAL MANUAL. COPRA Anchoring Coupler. For Smart Bolted Connections TECHNICAL MANUAL Anchoring Coupler For Smart Bolted Connections Version: PEIKKO GROUP 03/2017 Anchoring Coupler For bolted connections Multi-purpose anchoring system for all bolted connections Simplifi

More information

Low Wind High Yields Series

Low Wind High Yields Series Low Wind High Yields Series Wind Turbines USER S MANUAL Introduction Low Wind High Yields Series rotor blades apply the latest advanced thermoplastic engineering and are manufactured by precision injection

More information

SafeWaze Fall Protection Technical Data Sheet. General Information. Inspection and Examination

SafeWaze Fall Protection Technical Data Sheet. General Information. Inspection and Examination SideWalk 30,60, 100 Rope Horizontal Lifeline Systems General Information PD 4-30-08 The HORIZONTAL SAFETY LINES have been tested to the standards described in ANSI Z359.1-1992, CSA Z259.13-04 and certified

More information

HiPerMax LuK tooth chain for transmissions Reliable Power Flow in the Drive Train

HiPerMax LuK tooth chain for transmissions Reliable Power Flow in the Drive Train HiPerMax LuK tooth chain for transmissions Reliable Power Flow in the Drive Train Andreas Englisch Michael Pichura LuK SYMPOSIUM 2006 87 6 LuK tooth chain for transmissions Introduction A modern drive

More information

SPOKES & NIPPLES FOR BICYCLE 2017

SPOKES & NIPPLES FOR BICYCLE 2017 SPOKES & NIPPLES FOR BICYCLE 2017 HISTORY AND PRESENT Based in Lomagna, in the heart of Lombardy, Alpina Raggi S.p.A. was founded in 1926 and focusses its activity on the production of spokes and nipples.

More information

VSL MINING & TUNNELING SYSTEMS VSL. mining and tunneling

VSL MINING & TUNNELING SYSTEMS VSL. mining and tunneling VSL MINING & TUNNELING SYSTEMS VSL mining and tunneling VSL Mining & Tunneling Bolt systems VSL offers three type of bolting system for the mining & Tunnelling industry VSL-S Solid Threaded bolts. Continuous

More information

PHOENIX, ARIZONA USA

PHOENIX, ARIZONA USA NEW PRODUCTS MODEL: US-AASS-80 DESCRIPTION: Cantilever Arm 80 MEETS OSHA & ANSI Z359.14 CLASS B 1-800-850-5914 PHOENIX, ARIZONA USA WWW.ULTRASAFEUSA.COM CANTILEVER ARM The Ultra-Safe cantilever arm has

More information

XTS-Impact. XTS-Terminal (hold)

XTS-Impact. XTS-Terminal (hold) XTS-Impact The XTS-Impact is used to support the XTS-Linked system, as a standalone anchorage point and as an anchorage point in horizontal temporary lifeline systems. The anchorage point is tested according

More information

Erection, maintenance and disposal Inverted installation. Zinc oxide silicone-housed surge arresters PEXLIM R-X, Q-X and P-X

Erection, maintenance and disposal Inverted installation. Zinc oxide silicone-housed surge arresters PEXLIM R-X, Q-X and P-X Erection, maintenance and disposal Inverted installation Zinc oxide silicone-housed surge arresters PEXLIM R-X, Q-X and P-X 1 Important information The following instruction is valid for PEXLIM R-X, PEXLIM

More information

TRAVSMART permanent single-cable horizontal lifeline system

TRAVSMART permanent single-cable horizontal lifeline system The Travsmart single-line system provides a smooth travel. It allows the traveler to move freely over the intermediate anchors, minimizing wear and eliminating user assistance. The user s hands remain

More information

Highbond anchor FHB II-A S

Highbond anchor FHB II-A S Highbond anchor FHB II-A S The best performance in cracked concrete with the least installation effort VERSIONS APPROVALS zinc-plated steel stainless steel high corrosion-resistant steel ADVANTAGES BUILDING

More information

E 328 E 498 Tank top mounting Connection up to G1½ / -24 SAE and SAE 2 Nominal flow rate up to 600 l/min / gpm

E 328 E 498 Tank top mounting Connection up to G1½ / -24 SAE and SAE 2 Nominal flow rate up to 600 l/min / gpm Return-Suction Filters E 8 E 98 Tank top mounting Connection up to G½ / - SE and SE Nominal flow rate up to 6 l/min / 8. gpm Description pplication For operation in units with hydrostatic drives, when

More information

MEVA Guided Climbing MGC Technical Instruction Manual

MEVA Guided Climbing MGC Technical Instruction Manual MEVA Guided Climbing MGC Technical Instruction Manual Product Features MGC is the abbreviation for MEVA Guided Climbing and the name of MEVA s guided climbing system. Guided climbing means that after each

More information

ISO INTERNATIONAL STANDARD. Personal protective equipment for protection against falls from a height Single-point anchor devices

ISO INTERNATIONAL STANDARD. Personal protective equipment for protection against falls from a height Single-point anchor devices INTERNATIONAL STANDARD ISO 14567 First edition 1999-03-01 Personal protective equipment for protection against falls from a height Single-point anchor devices Équipements individuels de protection contre

More information

Preparation and Installation of the Sanitary BDI-FLX Sensor and Connection to the BDI-FLX Interface Cable

Preparation and Installation of the Sanitary BDI-FLX Sensor and Connection to the BDI-FLX Interface Cable GEP-6075 Rev. B 101574 Ref. I.D.: 16973 Preparation and Installation of the Sanitary BDI-FLX Sensor and Connection to the BDI-FLX Interface Cable WARNING USER SHOULD READ AND THOROUGHLY UNDERSTAND THESE

More information

FEA ANALYSIS OF PRESSURE VESSEL WITHDIFFERENT TYPE OF END CONNECTIONS

FEA ANALYSIS OF PRESSURE VESSEL WITHDIFFERENT TYPE OF END CONNECTIONS FEA ANALYSIS OF PRESSURE VESSEL WITHDIFFERENT TYPE OF END CONNECTIONS Deval Nitin Bhinde 1 and Rajanarsimha S. 2 1 MTech CAD-CAM & Robotics, 2 Facculty, Department of Mechanical Engineering K.J. Somaiya

More information

Linear Compressor Suction Valve Optimization

Linear Compressor Suction Valve Optimization Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2016 Linear Compressor Suction Valve Optimization Rinaldo Puff Embraco, Brazil, rinaldo.puff@embraco.com

More information

Fall Protection Checklist. Guardrail System

Fall Protection Checklist. Guardrail System Fall Protection Checklist Location/Department: Date of Inspection: Inspectors: Corrective Actions: Work order/memos were issued: Yes No Date issued: In accordance with the MIOSHA and OSHA standards the

More information

Pressure Reducing Valve DMV 755

Pressure Reducing Valve DMV 755 Pressure Reducing Valve DMV 755 Nominal size DN 10 50 Nominal size 3/8 2 Nominal pressure PN 10 bar Features pressure setting range 1 to 9 bar control valve for reliable reduction of system pressures to

More information

IAPMO GUIDE CRITERIA FOR BALL VALVES IAPMO IGC PURPOSE

IAPMO GUIDE CRITERIA FOR BALL VALVES IAPMO IGC PURPOSE INTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS IAPMO GUIDE CRITERIA FOR BALL VALVES IAPMO IGC 157-20067 1 PURPOSE 1.1 The purpose of this standard is to establish an acceptable standard

More information

IMO ANCHORING, MOORING AND TOWING EQUIPMENT. Submitted by the Republic of Korea

IMO ANCHORING, MOORING AND TOWING EQUIPMENT. Submitted by the Republic of Korea INTERNATIONAL MARITIME ORGANIZATION E IMO SUB-COMMITTEE ON SHIP DESIGN AND EQUIPMENT 48th session Agenda item 6 DE 48/6/1 17 November 2004 Original: ENGLISH ANCHORING, MOORING AND TOWING EQUIPMENT Shipboard

More information

Opening Angle 76º 30º [337] 45º 76º 30º [213] 45º 76º 30º [169] 45º 76º 30º [337] 45º 76º 30º [337] 45º 76º 30º [128] 45º 76º 30º [404] 45º 76º 30º

Opening Angle 76º 30º [337] 45º 76º 30º [213] 45º 76º 30º [169] 45º 76º 30º [337] 45º 76º 30º [337] 45º 76º 30º [128] 45º 76º 30º [404] 45º 76º 30º 17.22 Picture Force N [lbs] Opening Angle Weight Opening/closure time min 84A3-310000000 84A3X310000000 84A3Y310000000 84A3Z310000000 60º 1,35 84A3-0000000 84A3X0000000 950 84A3Y0000000 [213] 84A3Z0000000

More information

SG33KTL-M Quick Installation Guide. 1 Unpacking and Inspection

SG33KTL-M Quick Installation Guide. 1 Unpacking and Inspection SG33KTL-M Quick Installation Guide This guide provides a general instruction of the installation procedures of SG33KTL-M. In no case shall this guide substitute for the user manual or related notes on

More information

Operating instruction for the quick-change tap holders type:

Operating instruction for the quick-change tap holders type: type: HF 20 HF 30 Date of edition: 15.07.2008 Stage of alteration: 4 Please keep this for future use! Contents: 1 Application range, safety instructions and technical data... 3 1.1 Application range,

More information

MAKING MODERN LIVING POSSIBLE. Pilot operated internal safety valves type POV REFRIGERATION AND AIR CONDITIONING DIVISION.

MAKING MODERN LIVING POSSIBLE. Pilot operated internal safety valves type POV REFRIGERATION AND AIR CONDITIONING DIVISION. MAKING MODERN LIVING POSSIBLE Pilot operated internal safety valves type POV REFRIGERATION AND AIR CONDITIONING DIVISION Technical leaflet Contents Page Introduction...3 Features...3 Design...4 Technical

More information

Mounting instructions. Strain transducer SLB-700A. B 26.SLB700A.10 e

Mounting instructions. Strain transducer SLB-700A. B 26.SLB700A.10 e Mounting instructions Strain transducer SLB-700A B 26.SLB700A.10 e SLB700A 3 Contents Page Safety instructions.............................................. 4 1 Applications..................................................

More information

Steam Trap BK BK 212-ASME. Original Installation Instructions English

Steam Trap BK BK 212-ASME. Original Installation Instructions English Steam Trap BK 212.. BK 212-ASME EN English Original Installation Instructions 810609-02 1 Contents Page Important Notes Usage for the intended purpose... 3 Safety note... 3 Danger... 3 Attention... 3 Application

More information

TECH TIPS: ROPE DEFECTS

TECH TIPS: ROPE DEFECTS Hoist Ropes: Why must they be inspected? A hoist rope is not made to last forever. This is a useful fact, as the kinds of wear that appear on a rope can indicate areas of problems within an installation

More information

Proportional Pressure-Relief Cartridge Valve, Size 2...4

Proportional Pressure-Relief Cartridge Valve, Size 2...4 Proportional Pressure-Relief Cartridge Valve, Size... Q max = l/min (6 gpm), p max = bar (58 psi) Direct acting, electrically operated Description proportional pressure-relief valves are direct acting

More information

Hilti, Inc South 122 nd East Avenue Tulsa, OK

Hilti, Inc South 122 nd East Avenue Tulsa, OK Attached are page(s) from the 2014 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,

More information

Technical Data Sheet TI-F52 Locking Unit KFHL Certified by Lloyd s Register

Technical Data Sheet TI-F52 Locking Unit KFHL Certified by Lloyd s Register English translation of German original TI-F52 Locking Unit KFHL Certified by Lloyd s Register For a detailed functional description refer to Technical Information TI-F10. Further important practical advice

More information

ASME Boiler & Pressure Vessel Code Analysis of the 1497 MHz High-Current Cryomodule Helium Vessel

ASME Boiler & Pressure Vessel Code Analysis of the 1497 MHz High-Current Cryomodule Helium Vessel 1.0 Introduction ASME Boiler & Pressure Vessel Code Analysis of the 1497 MHz High-Current Cryomodule Helium Vessel Katherine Wilson 28 May 2007 To minimize the hazards associated with vacuum and pressure

More information

PRODUCT SPECIFICATION. SFP+ Cage and Cage Assembly 1 of 8 A

PRODUCT SPECIFICATION. SFP+ Cage and Cage Assembly 1 of 8 A SFP+ Cage and Cage Assembly 1 of 8 A 1.0 Objective This specification defines the performance, test, quality and reliability requirements of the _Small Form-factor Pluggage (SFP+) product. 2.0 Scope This

More information

User Instruction Manual For Davit Rescue System

User Instruction Manual For Davit Rescue System Instructions for the following series products: Rescue Davit System Model numbers 8004000 and 8302500 User Instruction Manual For Davit Rescue System This manual should be used as part of an employee training

More information

J. J. Daly Metal Improvement Company Paramus New Jersey USA

J. J. Daly Metal Improvement Company Paramus New Jersey USA Shot Peening-Current Trends, Future Prospects J. J. Daly Metal Improvement Company Paramus New Jersey USA The shot peening process is sparingly used compared to other processes such as heat treating, plating,

More information

TIGHTNESS. Glass sealing Thanks to our glass-sealing technology, ODU products can meet the most demanding tightness requirements.

TIGHTNESS. Glass sealing Thanks to our glass-sealing technology, ODU products can meet the most demanding tightness requirements. TIGHTNESS Glass sealing Thanks to our glass-sealing technology, ODU products can meet the most demanding tightness requirements. ODU has the necessary expertise for developing and manufacturing connectors

More information

Pressure relief valve DHV 725 set range: 0,2-10,0 bar

Pressure relief valve DHV 725 set range: 0,2-10,0 bar Pressure relief valve DHV 75 set range: 0, - 0,0 bar Advantage pressure setting possible at any time, also during operation optimum monitoring valves high reproducibility of the set pressure high level

More information

CARES Technical Approval Report TA1-B & C 5059

CARES Technical Approval Report TA1-B & C 5059 CARES Technical Approval Report TA1-B & C 5059 Issue 2 DEXTRA Griptec Anchors Assessment of the Griptec Anchors Product and Quality System for Production 5059 Product DEXTRA Griptec Anchors for reinforcing

More information

Comparison and Sensitivity Investigations of a CALM and SALM Type Mooring System for Wave Energy Converters

Comparison and Sensitivity Investigations of a CALM and SALM Type Mooring System for Wave Energy Converters J. Mar. Sci. Eng. 214, 2, 93-122; doi:1.339/jmse2193 Article OPEN ACCESS Journal of Marine Science and Engineering ISSN 277-1312 www.mdpi.com/journal/jmse Comparison and Sensitivity Investigations of a

More information

Pressure Relief Valve DHV 718

Pressure Relief Valve DHV 718 Pressure Relief Valve DHV 718 Nominal size DN 8 50 Nominal size 3/8 2 Nominal pressure PN 10 bar Features pressure setting range 0.5 to 10 bar diaphragm controlled pressure relief valve simple design,

More information

Brick & Concrete. Expandet ESI Xtreme Pro Injection Mortar ADVANTAGES. ACCESSORIES Wide range of accessories. INSTALLATION:

Brick & Concrete. Expandet ESI Xtreme Pro Injection Mortar ADVANTAGES. ACCESSORIES Wide range of accessories. INSTALLATION: Expandet ESI Xtreme Pro Injection Mortar Expandet ESI Xtreme Pro is the professional all round bonded anchor solution that provides expansion free, safe and fast anchorage of threaded rod, socket anchors

More information

FRONT DERAILLEUR - CURRENT RANGE

FRONT DERAILLEUR - CURRENT RANGE FRONT DERAILLEUR - CURRENT RANGE (since 2015) (since 2018) (since 2017) (since 2018) WARNING! This technical manual is intended for use by professional mechanics. Anyone who is not a qualified professional

More information

OR-V 41 P BETRIEBSANLEITUNG DEUTSCH ENGLISH FRANÇAIS ITALIANO MODE D'EMPLOI ISTRUZIONI PER L'USO

OR-V 41 P BETRIEBSANLEITUNG DEUTSCH ENGLISH FRANÇAIS ITALIANO MODE D'EMPLOI ISTRUZIONI PER L'USO DEUTSCH ENGLISH FRANÇAIS ITALIANO 3 10 17 24 BETRIEBSANLEITUNG OPERATING INSTRUCTIONS MODE D'EMPLOI ISTRUZIONI PER L'USO OR-V 41 P Ab Serie-Nr. 200 From serie no 200 A partir du no de série 200 A partire

More information

Data Distribution Cabinets. Exclusive CD edition March 2006

Data Distribution Cabinets. Exclusive CD edition March 2006 Exclusive CD edition March 2006 Introduction: The development of distribution cabinets is the practical reply from KRONE to the ever increasing demands on the data, telephone, and network technology. Cost-effective,

More information

Gas plug-in hose, straight-through form. Instructions for Use. suitable for gas socket model G2019T, G2016T. G2023 from 01/1990.

Gas plug-in hose, straight-through form. Instructions for Use. suitable for gas socket model G2019T, G2016T. G2023 from 01/1990. Gas plug-in hose, straight-through form Instructions for Use suitable for gas socket model G2019T, G2016T Model Year built: G2023 from 01/1990 en_int Gas plug-in hose, straight-through form 2 from 12 Table

More information

Hatch cover securing and tightness

Hatch cover securing and tightness (1986) (Rev 1 1996) (Corr.1 June 2000) (Rev.2 July 2005) (Corr.1 Oct 2005) Hatch cover securing and tightness 1. Application 1.1 The following recommendations apply to steel hatch covers that are fitted

More information

HELM Hinging facility according to EN 795:2012 Typ D. Sliding hardware

HELM Hinging facility according to EN 795:2012 Typ D. Sliding hardware HELM Hinging facility according to EN 795:2012 Typ D Sliding hardware Contents General Information General Information Page 3 Certification Page 4 Technical Information HELM Track profile Page 7 HELM Bends

More information

Proportional Pressure-Relief Cartridge Valve, Size 2...4

Proportional Pressure-Relief Cartridge Valve, Size 2...4 Proportional Pressure-Relief Cartridge Valve, Size... Q max = l/min, p max = 3 bar Direct acting, electrically operated 1 Description proportional pressure-relief valves are direct acting screw-in cartridges

More information

Solenoid gas valve. The solenoid gas valve is also applicable as a main gas valve Pilot gas valve for forced draft burners

Solenoid gas valve. The solenoid gas valve is also applicable as a main gas valve Pilot gas valve for forced draft burners 7 634 VGS1... with AGA67 connector VGS2... with AGA67 connector Solenoid gas valve VGS The solenoid gas valve is also applicable as a main gas valve Pilot gas valve for forced draft burners The VGS and

More information

MSA Latchways Solutions for Industry

MSA Latchways Solutions for Industry MSA Latchways Solutions for Industry Fall protection systems for industrial applications Overhead systems Horizontal systems LadderLatch VersiRail Self-Retracting Lifeline (SRL) MSA Latchways Solutions

More information

SITRANS P measuring instruments for pressure

SITRANS P measuring instruments for pressure SITRANS P measuring instruments for pressure Z series for gage pressure Siemens AG 008 Overview Design The main components of the pressure transmitter are: Brass housing with silicon measuring cell and

More information

BARRIER OFFSET 0" A 6" 6" A 12" 12" A 26" A 26" 3A OR 4A L OR S * ** L OR S L OR S

BARRIER OFFSET 0 A 6 6 A 12 12 A 26 A 26 3A OR 4A L OR S * ** L OR S L OR S ACCEPTABLE (TCB) TYPES AND ANCHORING DETAILS BASED ON UNDERLYING SURFACE TYPE AND BARRIER OFFSET FROM DROP-OFF BARRIER OFFSET UNDERLYING SURFACE 0" A 6" 6" A 12" 12" A 26" A 26" TCB TYPE DETAIL TCB TYPE

More information

RULES FOR CLASSIFICATION Ships. Part 3 Hull Chapter 5 Hull girder strength. Edition October 2015 DNV GL AS

RULES FOR CLASSIFICATION Ships. Part 3 Hull Chapter 5 Hull girder strength. Edition October 2015 DNV GL AS RULES FOR CLASSIFICATION Ships Edition October 2015 Part 3 Hull Chapter 5 The content of this service document is the subject of intellectual property rights reserved by ("DNV GL"). The user accepts that

More information

Presented to the International Technical Rescue Symposium, November Abstract

Presented to the International Technical Rescue Symposium, November Abstract Presented to the International Technical Rescue Symposium, November 21 Presented by: Chuck Weber, PMI Quality Manager Abstract This paper presents the results of 162 individual drop tests performed at

More information

Electrically Operated Pressure-Relief Cartridge, Size 10

Electrically Operated Pressure-Relief Cartridge, Size 10 Electrically Operated Pressure-Relief Cartridge, Size 1 Q max = 14 l/min (37 gpm), p max = bar (5 psi) seated pilot stage, spool-type design, with remote contral port Z Series WUVPOC-2, WUVPLC-2 1 Description

More information

Electropneumatic Positioner and Pneumatic Positioner Type 3760 JIS

Electropneumatic Positioner and Pneumatic Positioner Type 3760 JIS Electropneumatic Positioner and Pneumatic Positioner Type 3760 Application Single-acting positioners for direct attachment to pneumatic control valves. An electric standardized signal of 4 to 20 ma or

More information

MULTI-MONTI Technical manual

MULTI-MONTI Technical manual MUTI-MONTI Technical manual Version 01/2017 Technical manual MUTI-MONTI Content Instructions for fixing P. 3 Chapter 1: Admissible loads in as well as P. 4 anchor characteristics for MMS-6 to MMS-16 1.1

More information