45a. Ghid de asamblare. Numerele 45-48
|
|
- Mitchell Martin
- 5 years ago
- Views:
Transcription
1 Ghid de asamblare Numerele NUMĂRUL 45 Piesele oferite cu nr. 45:. Strips imitating the sheathing (veneer) 45a Now, we ll continue the sheathing of the starboard side. Glue the strips of the veneer along the body of the vessel. Glue first layer strips of the sheathing, as shown in the picture. 279 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
2 NAVE CELEBRE 45b In the bow side of the vessel, the strips should reach the keel (see the picture). 45c Using short pieces of the strips, sheath the aft part of the vessel. Cut carefully the exceeding parts of the sheathing. 280 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
3 SFÂNTUL IOAN BOTEZĂ TORUL 45d Stick the strips the way it is shown in the figure and then cut the exceeding parts of the sheathing. 45e Glue the strips on the bow side of the vessel. Helped by the wedge-shaped inserts, fill the gaps of the sheathing. 28 GV UK CNST LFLT 2.indd 28 22/03/202 :44 μ.μ.
4 NAVE CELEBRE 45f Helped by some pieces of strips, with the length of 50 mm, glue the rest of the ship's starboard side, as shown in the picture. In this case, the gun ports and other openings should be covered. 45g Wait the glue to dry. With a special knife or with a scalpel cut the gun ports and the scuppers, as shown in the picture. The forty-fifth stage of the assembly is completed. Keep the assembled structure in a place that ensures its safety, before the next step. 282 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
5 SFÂNTUL IOAN BOTEZĂ TORUL NUMĂRUL 46 2 Piesele oferite cu nr. 46:. Strips imitating the lining (veneer) 2. Strips for the construction of the gunwale.5 x 6 x 300 mm 46a Glue the two rows of strips along the length of the hull, putting them under the scuppers (see picture). Fill the gaps with wedge inserts. Mark with a pencil the location of the gun ports, which need to be cut later. Glue the strips of the veneer so that they cover the gun ports of the upper deck bulwark. 283 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
6 NAVE CELEBRE 46b With a special knife or with a scalpel, cut the porthole of the bottom and the top decks. 46c Finish the lining of the left side of the ship and cut the protruding strips. With fine emery paper, sand gently the hull. Avoid strong pressure, as you may damage the top layer of the sheathing. Collect the remaining sawdust and mix them with colourless glue, in order to get the material to fill the gaps. With a thin spatula fill the resulting gaps of the top layer of the sheathing. After the glue has dried, sand neatly the excesses of the glue. 284 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
7 SFÂNTUL IOAN BOTEZĂ TORUL d Measure the required length of the gunwale of the bow superstructure bulwark (see the picture) and cut the strips no. 2 according to these dimensions. Glue the strips so that they are overboard about.5 mm e Similarly, glue the gunwale of the upper deck bulwark. 285 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
8 NAVE CELEBRE 46f Set at its place the gunwale of the aft superstructure. 2 46g Gently sand the joints of the gunwale strips with the sanding block. The forty-sixth assembly stage is over. Keep the assembled structure in a place that ensures its safety, before the next step. 286 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
9 SFÂNTUL IOAN BOTEZĂ TORUL NUMĂRUL Piesele oferite cu nr. 47:. Strips of.5 x 6 mm for the construction of the gunwale 2. Strips of 0.6 x 20 mm for the bulwark decoration 3. Beams of.5 x 3 mm for the body finishing 4. Beams of 2 x 2 mm for the stern superstructure finishing 47a Cut out 0 segments of 6 mm from the strips no. for the construction of the gunwale and glue them to the remaining curved parts of the bulwark, as shown in the figure. Gently sand them, lining up differences in height and width and forming a smooth line. 287 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
10 NAVE CELEBRE 47b Pour a little of instant glue into a shallow container. When you work with details of small sizes, it will be easier to apply the adhesive on the right places with the help of an awl (needle): incline the container, take an awl and apply the droplets of glue on the right areas. 47c Glue the beams no. 4 of 2 x 2 mm, so that they continue the line of the bulwark gunwale in the upper deck; in the area of the transom stern, the distance between the beam and the gunwale should be of 5 mm (see the figure). Cut off the protruding pieces of the beams. 288 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
11 SFÂNTUL IOAN BOTEZĂ TORUL 47d Glue the beams no. 3 of,5 x 3 mm, as shown in the figure, from the front wall of the forecastle superstructure to the stern transom. Respect the distance indicated on the sidebars (0 mm at the front, 5 mm at the stern) e Glue the strips of,5 x 6 mm, as shown in the figure. In the bow side, the strip must pass under the first scupper. 289 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
12 NAVE CELEBRE 47f In the stern side of the ship, the strip should be placed under the grooves of the aft transom (see the picture). The strips must be symmetrical on both sides of the vessel. 47g Glue the strips of.5 x 6 mm to the aft transom, as shown in the figure. The strips no. 2 will be needed for the further phases of the work. The forty-seventh stage of the assembly is completed. Keep the assembled structure in a place that ensures its safety, before the next step. 290 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
13 SFÂNTUL IOAN BOTEZĂ TORUL NUMĂRUL 48 Piesele oferite cu nr. 48:. Gripe 2. Knee of the head 2 48a From the strips of 0.6 x 20 mm, remaining from the previous phase of work, create a work piece imitating the "space" between the elements of the superstructure aft trimming on the right side (see picture). In order to ease the work, you can prepare previously a pattern of heavy paper. Similarly, fabricate the detail for the left side. 29 GV UK CNST LFLT 2.indd 29 22/03/202 :44 μ.μ.
14 NAVE CELEBRE 48b Mark on the details nine equilateral triangles with the length of 8 mm. Start the markup from the front edge of the detail on the upper side (see picture). The triangles marked with "x" should be removed. 8 mm 48c Using a scissors, carefully cut out the triangles. 292 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
15 SFÂNTUL IOAN BOTEZĂ TORUL 48d Glue the triangles at their place with quick-drying glue. 48e Prepare the ornamental elements of the second row according to the dimensions shown in the figure. There is no need to glue the dark marked triangles. Prepare in a similar way the ornamental elements of the other side. 29 mm 24mm 24 mm 24 mm 24 mm 24 mm 24 mm 24 mm 20 mm 0 mm 293 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
16 NAVE CELEBRE 48f Separate the prepared elements of the breakwater from the substrate and gently sand them. Then, paint the components in a light color, imitating the "walnut". Glue the knee of the head (2) to the keel, as shown in the figure. Note that the protruding upper part is located above the deck of the vessel. 2 48g Glue the gripe () in a place so that it matches tightly the bottom of the keel and the knee of the head. The forty-eighth stage of the assembly is completed. Keep the assembled structure in a place that ensures its safety, before the next step. 294 GV UK CNST LFLT 2.indd /03/202 :44 μ.μ.
GREEK TRIREME, 480 B.C. Scale: 1/72 Length: 515mm Width: 180mm Height: 220mm
GREEK TRIREME, 480 B.C. Scale: 1/72 Length: 515mm Width: 180mm Height: 220mm HISTORY: The model represents a Greek Trireme from the age of battle of Salamis (480 B.C.). The crew were 170 oarsmen and about
More informationKNARR. SCALE: 1/35 length: 440mm width: 300mm height: 400mm
KNARR SCALE: 1/35 length: 440mm width: 300mm height: 400mm HISTORY: The Knarr is a type of Viking ship which serves for long trade naval business. The Knarrs were very robust and very well resist against
More informationMARIA HF31. SCALE: 1/72 Length: 365 mm width: 85mm height: 295 mm
MARIA HF31 SCALE: 1/72 Length: 365 mm width: 85mm height: 295 mm HISTORY: Maria HF 31 is a fishing Ewer whose home base was Finkenwerder in northern Germany. Maria HF31 operated in the North Sea for more
More informationStevenson Projects Building the Hull Top Deck and Bulkheads
Stevenson Projects Building the Hull 1. Print out both piece sheets. 2. Cut out one keel piece and glue it to a piece of balsa wood or dense cardboard. Cut out the second keel piece and glue it to the
More informationHansa COG 14 th century SCALE: 1/72 Length: 430mm Width: 210mm Height: 330mm
Hansa COG 14 th century SCALE: 1/72 Length: 430mm Width: 210mm Height: 330mm HISTORY: The Hansa was a medieval association of German cities which engaged by in long distance business mainly in area of
More informationVikings ship GOKSTAD, 9 th century Scale: 1/72 Length: 305mm Width: 135mm Height: 182mm
Vikings ship GOKSTAD, 9 th century Scale: 1/72 Length: 305mm Width: 135mm Height: 182mm HISTORY: This model represents a Viking ship found in year 1880 near village Gokstad in Norway. The ship was built
More informationSamurai Armor Set: Step by Step
Samurai Armor Set: Step by Step Pack 6 Stages -5 Contents Stage Pages 7-76 The tasset plates and shoulder pad Stage Pages 77-8 The tassets, helmet and helmet lining Stage Pages 8-86 The tasset plates and
More information8-GUN CORVETTE ASSEMBLY INSTRUCTIONS
8-GUN CORVETTE ASSEMBLY INSTRUCTIONS THE HULL STEP 1 Fasten the Deck to the Hull. Find the hull. This is a large, pink, ship-shaped piece of insulating foam board. This will form the base of your model
More informationaero naut Order No. 3009/00
aero naut Order No. 3009/00 Introduction: The model should be assembled following the sequence of the stages of construction described in these instructions. The laser-cut components are individually numbered.
More informationRATLINER Assembly Instructions.
Model Shipways Inc. www.modelexpo-online.com RATLINER Assembly Instructions. Patent Pending 1. Remove center stands and braces from the main rigging frame. 2. The Stands and Braces should press release
More informationINSTRUCTIONS FOR GLUING ON THE BUMPER FOR PORT TOWNSEND WATERCRAFT S NESTING DINGIES. (Or requires a 1 surface to adhere to.)
INSTRUCTIONS FOR GLUING ON THE BUMPER FOR PORT TOWNSEND WATERCRAFT S NESTING DINGIES. (Or requires a 1 surface to adhere to.) The PT 11 bumper is made from a high quality, non marking EPDM rubber. This
More informationH.M. SCHOONER PICKLE THE TRAFALGAR DISPATCH
H.M. SCHOONER PICKLE THE TRAFALGAR DISPATCH Manual 1 of 2 Hull Construction, Masting & Rigging Additional photos of every stage of construction can be found on our website at: http://www.jotika-ltd.com
More informationWe hope you ll enjoy the Drifter as much as we have! Scott DeTray Model Aero Specifications:
We are excited to bring you the Drifter RC airboat. You re probably thinking it doesn t fly so what is Model Aero thinking??? We have always liked RC vehicles of all types and have had a fondness for airboats
More informationIn each step, the needed parts are shown the number right below. Locate all parts for the step.
Tools Required for Assembly Phillips Screwdriver, Med Needle Nose Pliers Sandpaper (#400 grit) Hobby Knife Scissors CA Instant Glue Rubbing Alcohol Drill Bit 1/16", 1.6mm 5/64, 2mm 1/8, 3mm 5/32, 4mm Before
More informationBuilding the Corel Endeavour
SPECIAL ISSUE # 7 DECEMBER 2017 All photographs and articles published remain the copyright property of the contributor and SMSC unless released. Building the Corel Endeavour Photos and commentary by Leon
More informationCONSTRUCTION OF A GUNBOAT A CLASS YACHT by Brian Dill
CONSTRUCTION OF A GUNBOAT A CLASS YACHT by Brian Dill The Gunboat design is the latest Radio A class from Graham Bantock, optimised to provide the best boat speed below 4 knots and to be as good as possible
More informationLeopard-class Dropship
Leopard-class Dropship By Dog Hair Terrain (For use with Battletech, Mechwarrior: Dark Age, or 6mm/1:285 micro armor games) Printing. This model was designed to be printed on 8 ½ x 11 paper. It should
More informationConstitution Instructions
Constitution Instructions This kit will build a 1:48 scale hull for the USS Constitution frigate. The kit contains the following parts. 1/8 deck with laser etched deck lines 1/8 railing Ribs Center keel
More informationRain Gutter Regatta Pack Event
Rain Gutter Regatta Pack Event Sunday July 24 th Check-in: 1:30PM Races start: 2 PM Location: 4512 Hoffman Farms Drive Cost: $4/boat kit Organizer: Matt Cook Ahoy, Mates! Although the seas are only 10-foot
More informationShips of the world : Esmeralda : Assembly Instructions
http://www.canon.com/c-park/ Before starting assembly: Writing the number of each section on its back side before cutting out the sections is highly recommended. (* This way, you can be sure which section
More informationYour kit contains the following items. Additional Items You May Need. Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet
Your kit contains the following items Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet The SkyFox offers great glide performance in a rubber powered plane due to its built up wing.
More informationBogue Class Escort Carrier Kit
Bogue Class Escort Carrier Kit This kit will build a Bogue Class Escort Carrier from WW II, suitable for running as a R/C navel combat ship or convoy ship. During WWII, 43 of these ships were built by
More informationChapter Twelve. Starting the rigging process
Chapter Twelve Starting the rigging process Before I begin describing the rigging process, I must remind folks that it would be a great time to slip that traveler ring onto the bowsprit. I forgot to mention
More informationConstruction Chapters Index
Construction Chapters Index 9 7 8 Chapters Index c. c. c. c. c. c. c7. c8. c9. c0. c. c. c. c. c. c. c7. Balsa Wood Skeleton Strip Planking Hull Fairing Keel Bulb Mould Lead Bulb Casting Keel Construction
More informationMiss Mayflower. Build Manual
Miss Mayflower Build Manual Thank you for the purchase of the Miss Mayflower, this new exciting craft will give you fun on many types of terrain including snow, gravel, pavement, grass, water, and when
More informationCATBOX. A Puddle Duck Racer. By Jim Michalak
CATBOX A Puddle Duck Racer By Jim Michalak CAT BOX HULL SPECIFICATIONS 1. Bow transom from 1/4" plywood. Top and bottom edges framed with 3/4 x 1-1/2" lumber with bevels as shown. Mark centerlines boldly.
More informationUSS. Build the CONSTITUTION. The world s oldest commissioned naval vessel afloat
USS ONSTITUTION uild the The world s oldest commissioned naval vessel afloat 11 uild the USS ST ONSTITUTION ontents P 101 The mainmast 223 102 Mainmast yards and fittings 225 103 Yards and fittings 227
More informationBuilding the Model Shipways kit of the colonial schooner Sultana
Building the Model Shipways kit of the colonial schooner Sultana Introduction by Chuck Passaro These shop notes have been prepared for those of you who enjoy the hobby and wish to take their modeling projects
More informationEuromodel Falmouth Part 5 SHIP S BOAT - v.03. An interpretive build of the. SHIP S BOAT.05.v.03
TRANSLATION LINKS 1. type into your browser... english+italian+glossary+nautical terms 2. utilise the translation dictionary Nautical Terms & Expressions from Euromodel website An interpretive build of
More informationTugster. Tug Boat. Competition or Sport Tug Kit. A Zippkits R/C Boat. Building Instructions
Z I P P M A N U FA C T U R I N G Tugster Tug Boat Competition or Sport Tug Kit A Zippkits R/C Boat Building Instructions 2016 JMP Hobby Group St. Paul, Indiana 47272 www.zippkits.com Toll Free (866) 922-ZIPP
More informationTHE AMERICAN BARN DOOR KITE
THE AMERICAN BARN DOOR KITE Oregon Kitemaker s Retreat January 2007 Rod Beamguard 4104 NW 112 th Way Vancouver, WA 98685-3578 (360) 574-8050 home (360) 750-9833 office kytfevr@wa-net.com PLANFORM BARN
More informationLE CERF, Scale: 1/72 Length: 685mm Width: 255mm Height: 520mm
LE CERF, 1779-1780 Scale: 1/72 Length: 685mm Width: 255mm Height: 520mm HISTORY: The cutter LE CERF was build after the plans of well known French ship designer Denys. The CERF was launched in March 2,
More informationBuilding a model of a Thames Barge
Building a model of a Thames Barge Stage 1 : Reading the instructions The model which I purchased is of the Will Everard, a steel-hulled barge built in the 1920's, one of a range of laser-cut kits from
More informationAssembly Instruction - Triton Vuoksa 2 advanced Touring kayak
Assembly Instruction - Triton Vuoksa 2 advanced Touring kayak QR-Code assembly video: You can find many assembling videos to our boats on our YouTube channel: https://www.youtube.com/c/faltbootde Assembly
More informationParts of the Ship. Terms you should already know
Parts of the Ship Toronto Brigantine Terms you should already know After-peak Fore-peak Bow Stern Fairlead Scupper Freeing port Hull Deck Lifeline Hatch Skylight Cleat Pin-rail Fife-rail Spider-band Block
More informationCarving Ship Model Hulls Laminated and Machine Carved Hulls
Carving Ship Model Hulls Laminated and Machine Carved Hulls Pete Jaquith 09 June 2015 Topsail Schooner Eagle 1847 Topsail schooner rig Built in Arrowsic Island, ME in 1847 3/16 to the foot, 1:64 scale
More informationAliphatic Resin Wood Glue. 18" Fabric Parachute Part #PNC50 Part # Part #11700 Part #J0016. Launch Lug
ADANCED * What you will need to build the Quest High-Q Hobby Knife * Straight Edge Pencil Aliphatic Resin Wood Sanding Sealer & Brush Spray Paint Parts and exploded view of the Quest High-Q Nose Cone 18"
More informationPhoto Essay: How to Build a Nova Scotian Grand Banks Dory By Jeff Spira Plans available at: http://spirainternational.com/ How to Build a Nova Scotian Grand Banks Dory By Jeff Spira In Lunenburg, Nova
More informationwww.aquaglidekayak.com WORK SPACE AND TOOLS 1. Take care to position yourself in a clean, dry area with good ventilation. For proper curing of adhesives, temperature should remain above 10 C (50 F).
More informationNAUTICAL TERMINOLOGY
It s important to have a basic understanding of common nautical terms associated with the parts, positions and directions of your vessel. Knowing these terms will make it easier to communicate with people
More informationT27 The Classic Beauty of a Timeless Yacht. created by William Lesh
T27 The Classic Beauty of a Timeless Yacht created by William Lesh Tippecanoe Boats, ltd 2007 Tippecanoe Boats, ltd 2007 T27 Racing Sloop - Radio Control Yacht 4 ft. 26.5 in. Fast Sailing and elegant,
More informationNo.5550 INTRUCTION MANUAL WARRANTY WARNING. Notice This is not a toy. Assembly and operating of this boat requires adult supervision.
INTRUCTION MANUAL WARRANTY Thunder Tiger guarantees this model kit to be free from defects in both material and workmanship. The total monetary value under warrant will in no case exceed the cost of the
More informationSamurai Armor Set: Step by Step
Samurai Armor Set: Step by Step Pack 3 Stages 9-12 1 Contents Stage 9 Pages 29-31 The cuirass side and tassets Stage 10 Pages 32-37 The shoulder plate and tassets Stage 11 Pages 39-41 The shoulder plate
More information275 RID Assembly Instructions
75 RID Assembly Instructions Part No. 0003003 v. Lscsep0 PARTS LIST (Specifications and contents subject to change without notice) Description Part # A. RID Track...0000050 B. Capacity Plate...0053 C.
More informationCub Scout Pack Rain Gutter Regatta
Cub Scout Pack 350 2014 Rain Gutter Regatta Event Location & Date: Advance Firehouse, Saturday November 22nd 11:00am-1:00pm (racing as soon as everyone registers) 106 E Wall Street Advance, IN 46102-9407
More informationAssembly instructions nortik scubi 2 Recreational kayak
Assembly instructions nortik scubi 2 Recreational kayak QR-Code assembly video: Assembly instructions nortik scubi 2 Dear Customer, You have purchased a nortik scubi 2, an innovative hybrid kayak for recreational
More informationPakboats PakCanoe Assembly Instructions
Pakboats PakCanoe Assembly Instructions Note: Please read these assembly instructions carefully before assembling the canoe. a A. Assembling the canoe Note: Don't be afraid to get into the canoe while
More informationSails. Sails: extract from 'Super-detailing the Cutter Sherbourne' page 1 George Bandurek
Sails There are many arguments for adding or omitting the sails on a model ship. There is no right answer and I decided to have a combination of set and furled sails on my model of HM cutter Sherbourne
More informationBuilding your first hull.
Building your first hull. You ve built your first model boat from a kit, and now you re ready to scratch-build a scale model. You may find what you need as a ready-made hull. Alternatively you may decide
More informationEaster Bunny Pompoms
Easter Bunny Pompoms When I was younger I remember it taking ages to make pompoms because of constantly passing a ball of yarn through the middle of two cardboard circles. Well this method makes it a lot
More informationOPERATIONS SEAFARER CERTIFICATION GUIDANCE NOTE SA MARITIME QUALIFICATIONS CODE
Page 1 of 8 Compiled by Chief Examiner Approved by Qualifications Committee: 27 September 2013 OPERATIONS SEAFARER CERTIFICATION GUIDANCE NOTE SA MARITIME QUALIFICATIONS CODE Page 2 of 8 KNOWLEDGE, UNDERSTANDING
More informationDEAR CUSTOMER. Water Fun 275 & 300
Water Fun 275 & 300 DEAR CUSTOMER Thank you for choosing a boat from Water Fun. We are confident that the boat will give you many fine moments at sea. It is recommended that you read the entire manual
More informationSwing Your Partner. by Beth Hester. GH Productions, Inc. The Basket Maker's Catalog
Swing Your Partner by Beth Hester GH Productions, Inc. The Basket Maker's Catalog Materials are available from your basketry supply store or contact: The Basket Maker's Catalog GH Productions, Inc. 521
More informationGluing Guide QCS Oval & Quick Cuff
Gluing Guide QCS Oval & Quick Cuff General information SI TECH has an extensive background and history in the development and design of premium drysuit components that dates back to the early 1960 s. This
More information34. Aft view of the boat at it s highest point.
32. The repaired holes. Still looks pretty ugly, though maybe not quite as bad. The epoxy probably isn t strong enough to make any difference in strength, but you never know of a piece of masking tape.
More informationMelon-Shaped Egg Basket
Melon-Shaped Egg Basket GH PRODUCTIONS, INC. The Basket Maker's Catalog Materials are available from your basketry supply store, or contact: GH Productions, Inc. The Basket Maker's Catalog 521 E. Walnut
More informationJohn with his stiff back, rows Caravan Leghorn ashore in the KISS dinghy.
The Kiss Dinghy (Keep It Stupid, Simple.) My friend Caravan had been using the prototype for a year when I asked him how it was going. It is phenomenally sensible. He replied. John is crippled with a bad
More information1/10 th Scale 1956 Ted Jones Classic Hydroplane
1/10 th Scale 1956 Ted Jones Classic Hydroplane Preparation These plans show outside sheeting of 3/32 balsa laminated with 1/64 birch ply. This makes a light and strong skin for this boat. Optionally you
More informationInstructions MANUAL. Folding kayak NERIS-3
Instructions MANUAL Folding kayak NERIS-3 1. General description NERIS-3 is a touring folding kayak ideal for flat Technical features: water trips on rivers, lakes and water Loading capacity 375 kg reservoirs.
More informationAssembly Instructions. for. Puffin Saranac. ScanSport, Inc. P.O. Box 700 (234 May Street) Enfield, New Hampshire Phone: (603)
Assembly Instructions for Puffin Saranac ScanSport, Inc. P.O. Box 700 (234 May Street) Enfield, New Hampshire 03748 Phone: (603) 632 9500 Fax: (603) 632 5611 info@pakboats.com www.pakboats.com Assembling
More informationPre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender
Pre-Paint>Fuselage>Empennage>Fit vertical tail fin Objectives of this task: To fit the vertical tail fin to the fuselage, including fitting the static probe, static tube, optional strobe light wiring and
More informationSHIP FORM DEFINITION The Shape of a Ship
SHIP FORM DEFINITION The Shape of a Ship The Traditional Way to Represent the Hull Form A ship's hull is a very complicated three dimensional shape. With few exceptions an equation cannot be written that
More informationPaddle Steam Ferry COMMODORE PERRY
A FREE PAPER MODEL TO DOWNLOAD AND CONSTRUCT A SCALE 1/250 Paddle Steam Ferry COMMODORE PERRY USS Commodore Perry was one of many ferries and other civilian craft that were converted to serve in the Union
More informationAdding Sculpted Toes to a Cloth Doll Foot
Adding Sculpted Toes to a Cloth Doll Foot by Sherralyn St. Clair, www.sherralynsdolls.com Many cloth doll patterns leave the doll's foot as a simple rounded shape. I have found that adding sculpted toes
More informationGRP BOAT BUILDING INSTRUCTIONS 2006
125 ASSOCIATION VICTORIAN DIVISION INC. GRP BOAT BUILDING INSTRUCTIONS 2006 TABLE OF CONTENTS 1.0 COPYRIGHT 4 2.0 PLAN SET and MEASUREMENT 4 3.0 MATERIALS FOR HULL 4 3.1 Patterns 4 3.2 Foam Panels 4 3.3
More informationRobotic Yacht. The construction of Birdy II. Paul
Robotic Yacht The construction of Birdy II Paul Table of Contents Introduction... 3 Construction... 4 Superstructure... 4 Birdy II... 5 Building Frame... 6 Bulkheads... 7 Drawing the Waterline... 7 Keel
More informationPuffin Sport and Saco
Puffin Sport and Saco Assembly and User Information Pakboats/ScanSport, Inc. Post Office Box 700 May Street Enfield, New Hampshire 03748 USA Phone: (888) 863-9500 (toll free) From outside the US: +1 (603)
More informationSkinning without a Needle: Fastening a skin around a kayak or boat frame, using splines an open-source project? Text and photos by Robert Morris
Skinning without a Needle: Fastening a skin around a kayak or boat frame, using splines an open-source project? Text and photos by Robert Morris Introduction One of the lovely qualities of the skin-on-frame
More informationPAY N PAK, 1/12 th Scale, Limited Sport Hydro P Sport Hydro
1980 82 PAY N PAK, 1/12 th Scale, Limited Sport Hydro P Sport Hydro Introduction: The 1980 turbine Pay N Pak is a good subject for a model race boat. It has a low profile, mild pickle-fork setback, long
More informationASSEMBLING INSTRUCTION - TRITON LADOGA 2 ADVANCED
ASSEMBLING INSTRUCTION - TRITON LADOGA 2 ADVANCED Touring and sea kayak Assembly video: Assembling Instruction - Triton Ladoga 2 advanced Dear Customer, At first: please do not be alarmed by the extent
More informationINTERNATIONAL FLYING FIFTEEN CLASS MEASUREMENT FORM
INTERNATIONAL FLYING FIFTEEN CLASS MEASUREMENT FORM 2014 Authority: * International Sailing Federation, Ariadne House, Town Quay, Southampton, Hampshire, SO14 2AQ, UK IN ORDER TO OBTAIN A MEASUREMENT CERTIFICATE
More informationConstructing the Masts
A: Fore Mast completed B: Main Mast unpainted C: Boom Rest D: Unpainted mast detail (fore and main mast) A D B C Constructing the Masts The main and fore masts are virtually identical. At least as far
More informationMarking films application guide
Marking films application guide The application techniques that we will describe should help users by making their job easier, or by saving them time. However, we know that all the advice in the world
More informationUMBILICAL CORD MODEL FOR UMBILICAL VEIN CATHETERIZATION TRAINING
UMBILICAL CORD MODEL FOR UMBILICAL VEIN CATHETERIZATION TRAINING A Guide to its Construction and Usage INTRODUCTION Introduction This training model aims to familiarize clinicians with umbilical vein catheterization
More informationInstructions MANUAL. Folding kayak NERIS-2 (tandem)
Instructions MANUAL Folding kayak NERIS-2 (tandem) 1. General descrition NERIS-2 is a touring folding kayak ideal for flat water trips on rivers, lakes and water reservoirs. It is also suitable for sea
More informationE Manual Self tacking system 30
597-205-E 2015-12-09 Manual Self tacking system 30 1 Self tacking system 30, 443-200-10 A self-tacking jib makes life on board a lot easier, in particular for shorthanded crews. The jib sheet is led to
More informationBasic Install Guide. Parts: 1 P a g e
Basic Install Guide Parts: 1 P a g e Step One: Remove all panels and components from boxes. Step Two: Carefully unroll your turf. Be sure not to cut the turf when removing from protective plastic. The
More informationSmall, Lightweight, Very Portable and Low Cost. Print in Landscape Mode with ¼ inch borders.
The 1 SHEET WEDGE Drawn 09-20-2015 Small, Lightweight, Very Portable and Low Cost Ken Simpson Designs Rev 07-31-2016 Print in Landscape Mode with ¼ inch borders It may look similar to some of my other
More informationFeaturing Coats Dual Duty XP. Supplies
Halloween Black Cat Basket Technique: Designed By: Skill Level: Crafting Time: Finished size: Sewing, Fabric Crafting Linda Turner Griepentrog Intermediate An evening 6" (15.24cm) (at base) x 3 1 2" x
More informationAPPENDIX IV DEVELOPMENT AND MEASUREMENT RULES OF THE INTERNATIONAL TEN SQUARE METER SAILING CANOE
APPENDIX IV Development Canoe Rules APPENDIX IV DEVELOPMENT AND MEASUREMENT RULES OF THE INTERNATIONAL TEN SQUARE METER SAILING CANOE 1 GENERAL Class and measurement rules measurement forms may be obtained
More informationShrouds, dead-eyes and ratlines
Shrouds, dead-eyes and ratlines On a real vessel the shrouds would be put up before the running rigging and many modellers follow this sequence. On Sherbourne I attached the stays and the running rigging
More information1. For the purposes of this standard, the maximum weight capacity of a boat is:
1. For the purposes of this standard, the maximum weight capacity of a boat is: a. The maximum load the boat may carry plus 32 divided by 141 b. The load displayed on the capacity label c. The load displayed
More informationVacuum Bagging Wings Instruction Manual Purdue University
Vacuum Bagging Wings Instruction Manual Purdue University Note: Do not leave the vacuum pump running unattended! Revision: Original Release 10/31/15 Vacuum bagged wings are quick to build, light weight,
More informationKayaking Bob s Tandem Island SpraySkirt Kit Installation Instructions
Kayaking Bob s Tandem Island SpraySkirt Kit Installation Instructions Copyright 2011 by R. E. & D. L. Conlon Kit Contains: Right & Left SpraySkirts 3 Long Black Wire Ties* 3 Short Black Wire Ties* 1 3/16
More informationCarbo Racing Foil Instruction Manual Unit 0, 1, 2, 3
Carbo Racing Foil Instruction Manual Unit 0, 1, 2, 3 WARNING!: Strictly follow all instructions to avoid an accident, damage to your vessel, personal injury or death. See www.harken.com/manuals for additional
More informationTrogear Bowsprit Through Hull Installation Manual
Trogear Marine Products, LLC www.trogear.com info@trogear.com 866-616-2978 Trogear Bowsprit Through Hull Installation Manual Congratulations on your purchase of the Trogear Bowsprit which can be installed
More informationBASIC COROPLAST HULLS FOUR HULLS, all single occupant designs. Choose the one that suites your needs.
BASIC COROPLAST HULLS FOUR HULLS, all single occupant designs. Choose the one that suites your needs. The build notes for one hull 5 type should 8 apply to all hull types. 1 CUT these 2 lines First 20
More informationBlazer Marine, Whiplash Sport 40
Blazer Marine, Whiplash Sport 40 Thank you for choosing to build the Whiplash 40. We have spent over 12 years perfecting this design, and finally we are making it available to the world. We are excited
More informationPACK 24 RAINGUTTER REGATTA November 19, 2010 (7pm at Hawthorne)
PACK 24 RAINGUTTER REGATTA November 19, 2010 (7pm at Hawthorne) Welcome to the Pack 24 Raingutter Regatta! Get ready for a night of excitement, action and a lot of hot air. The premise of Raingutter Regatta
More informationAngel 250 Angel 250 (H) Angel 300 Angel 300 (H) Angel 330 Angel 330 (H)
Angel 250 Angel 250 (H) Angel 300 Angel 300 (H) Angel 330 Angel 330 (H) Owner s manual www.silvermarine.com CONTENTS GENERAL INTRODUCTION...2 STRUCTURE TERMINOLOGY...3 TECHNICAL SPECIFICATIONS...3 PARTS
More informationAn Australian Classic by spectre.com
An Australian Classic by www.go spectre.com Your Bug! Welcome to the Balain Bug experience!!!!!! The Bug kit has been designed so as to be a modern version of the Traditional Bug now you can sail like
More information18. Tailplane torque-tube
18. Tailplane torque-tube Step 1 Fu se lage rear bulkhead Remove the three part templates of the rear bulkhead: an A4 size sheet from Annex A (page 5) and two A3 size sheets from Annex F of the manual,
More informationMANDATORY BULLETIN No.: SAFETY RELATED. EV a SR. Appendix 1 Bulletin Flow Chart
Appendix 1 Bulletin Flow Chart Form No.: QS-406/F-03A Issue: Date of Issue: Page: 2 APPENDIX 2 Inspection of Nicopress Pressing Tooling: Vernier calliper or Nicopress check gauge Felt-tip pen to mark clamps
More informationHow To Build A Water Rocket
How To Build A Water Rocket DESIGN AND DEVELOPMENT Brainstorm The first step in the design of a water bottle rocket is brainstorming. Brainstorming is a problem-solving technique that involves the spontaneous
More informationPuffin Sport Assembly and User Information
Puffin Sport Assembly and User Information ScanSport, Inc. / Pakboats Post Office Box 700 May Street Enfield, New Hampshire 03748 USA Phone: (888) 863-9500 (toll free) From outside the US: +1 (603) 632-9500
More informationRUDDER KIT INSTRUCTIONS
A I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS TARPON 0/40/60/60i The Tarpon series is designed as a high performance sit-on-top kayak tailored for the sport paddler. Our rudder system is designed to
More informationSTUDY GUIDE A Day By Day Course Refreshment Quiz To Ensure That You Make The Most Out Of Your Rod Building Class
DAY ONE: 1) Why would you want to build your own fishing rod? a. It s fun and rewarding b. You can customize your rod to your needs c. You can save money d. All of the Above 2) The main part of a fishing
More informationMaking Spars for the Schooner Jeanette
Making Spars for the Schooner Jeanette..... by Byron Rosenbaum Figure 1. Byron Rosenbaum s 1:16-scale radio-controlled model of the schooner Jeanette. All photographs by the builder. The spars required
More informationChapter Fourteen. Foresale Halliard
Chapter Fourteen Foresale Halliard The foresail halliard was rigged using.018 tan rope. You will need two 3/16 single blocks. One should have a hook seized to its end. The hook can be made from 24 gauge
More informationAssembling Instruction - Triton Ladoga 1 advanced Allround touring and sea kayak
Assembling Instruction - Triton Ladoga 1 advanced Allround touring and sea kayak 1 Assembling Instruction - Triton Ladoga 1 advanced Dear Customer, At first: please do not be alarmed by the extent of these
More information