Owner s Manual For M452 and M492 Series Spur Gear Hand Winches ORIGINAL TEXT

Size: px
Start display at page:

Download "Owner s Manual For M452 and M492 Series Spur Gear Hand Winches ORIGINAL TEXT"

Transcription

1 Red this Owner s Mnul thoroughly efore operting the equipment. Keep it with the equipment t ll times. Replcements re ville from Thern, Inc., PO Box 347, Winon, MN 55987, IMPORTANT: Plese record product informtion on pge 2. This informtion is required when clling the fctory for service. ORIGINAL TEXT Owner s Mnul For M452 nd M492 Series Spur Ger Hnd Winches

2 pge 2 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches Two-Yer Limited Wrrnty Plese record the following: Dte Purchsed: Model No.: Code No.: This informtion is required when clling the fctory for service. Thern, Inc. wrrnts its products ginst defects in mteril or workmnship for two yers from the dte of purchse y the originl using uyer, or if this dte cnnot e estlished, the dte the product ws sold y Thern, Inc. to the deler. To mke clim under this wrrnty, contct the fctory for n RGA numer. The product must e returned, prepid, directly to Thern, Inc., 5712 Industril Prk Rod, Winon, Minnesot The following informtion must ccompny the product: the RGA numer, the dte of purchse, the description of the climed defect, nd complete explntion of the circumstnces involved. If the product is found to e defective, it will e repired or replced free of chrge, nd Thern, Inc. will reimurse the shipping cost within the contiguous USA. This wrrnty does not cover ny dmge due to ccident, misuse, use, or negligence. Any ltertion, repir or modifiction of the product outside the Thern, Inc. fctory shll void this wrrnty. This wrrnty does not cover ny costs for removl of our product, downtime, or ny other incidentl or consequentil costs or dmges resulting from the climed defects. This wrrnty does not cover rke discs, wire rope or other wer components, s their life is suject to use conditions which vry etween pplictions. FACTORY AUTHORIZED REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY TO THE CONSUMER. THERN, INC. SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. Some sttes do not llow the exclusion or limittion of incidentl or consequentil dmges, or llow limittions on how long n implied wrrnty lsts, so the ove limittion or exclusion my not pply to you. This wrrnty gives you specific legl rights, nd you my lso hve other rights which vry from stte to stte. Note: Thern, Inc. reserves the right to chnge the design or discontinue the production of ny product without prior notice. Aout This Mnul The Occuptionl Sfety nd Helth Act of 1970 sttes tht it is the employer s responsiility to provide workplce free of hzrd. To this end, ll equipment should e instlled, operted, nd mintined in complince with pplicle trde, industril, federl, stte, nd locl regultions. It is the equipment owner's responsiility to otin copies of these regultions nd to determine the suitility of the equipment to its intended use. This Owner s Mnul, nd wrning lels ttched to the equipment, re to serve s guidelines for hzrd-free instlltion, opertion, nd mintennce. They should not e understood to prepre you for every possile sitution. The informtion contined in this mnul is pplicle only to the Thern Model M452 nd M492 Spur Ger Hnd Winches. Do not use this mnul s source of informtion for ny other equipment. The following symols re used for emphsis throughout this mnul: Filure to follow WARNING! instructions my result in equipment dmge, property dmge, nd/or serious personl injury. Filure to follow CAUTION! instructions my result in equipment dmge, property dmge, nd/or minor personl injury. Importnt! Filure to follow importnt! instructions my result in poor performnce of the equipment.

3 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge 3 Suggestions for Sfe Opertion DO the following: Red nd comply with the guidelines set forth in this Owner s Mnul. Keep this mnul, nd ll lels ttched to the winch, redle nd with the equipment t ll times. Contct Thern, Inc. for replcements. Check luriction efore use. Instll the wire rope securely to the winch drum. Keep t lest 4 wrps of wire rope wound on the drum t ll times, to serve s nchor wrps. Filure to do so could cuse the lod to escpe. Keep hnds wy from the drum, gers, wire rope, nd other moving prts of the equipment. Keep ll unnecessry personnel wy from the winch while in opertion. Keep out of the pth of the lod nd out of the pth of roken wire rope tht might snp ck nd cuse injury. DO NOT do the following: Do not lift people, or things over people. Do not wlk or work under lod or in the line of force of ny lod. Do not exceed the lod rting of the winch or ny other component in the system. Do not operte with other thn mnul power. Do not use more thn one winch to move lod unless ech winch ws designed for use in multiple winch system. Do not use dmged or mlfunctioning equipment. To do so could result in filure of the equipment. Do not modify the equipment in ny wy. To do so could cuse equipment filure. Do not wrp the wire rope round the lod. This dmges the wire rope nd could cuse the lod to escpe. Use sling or other pproved rigging device. Do not operte the winch with gurds removed or improperly instlled. Do not divert your ttention from the opertion. Sty lert to the possiility of ccidents, nd try to prevent them from hppening. Do not jerk or swing the lod. Avoid shock lods y strting nd stopping the lod smoothly. Shock lods overlod the equipment nd my cuse dmge. Do not lift lods or pull lods on n incline unless the winch is equipped with rke. Do not leve suspended lod unttended unless specific precutions hve een tken to secure the lod nd keep people wy from the winch nd from under the lod.

4 pge 4 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches 1.1 Instlling the Winch Importnt! Inspect the winch immeditely following instlltion ccording to the Instructions for Periodic Inspection. This will give you record of the condition of the winch with which to compre future inspections. A qulified professionl should inspect or design the foundtion to insure tht it will provide dequte support. Locte the winch so it will e visile during the entire opertion. Do not instll the winch in n re defined s hzrdous y the Ntionl Electric Code, unless instlltion in such n re hs een thoroughly pproved. Do not instll the winch ner corrosive chemicls, flmmle mterils, explosives, or other elements tht my dmge the winch or injure the opertor. Adequtely protect the winch nd the opertor from such elements. Position the winch so the opertor cn stnd cler of the lod, nd out of the pth of roken wire rope tht could snp ck nd cuse injury. Attch the winch to rigid nd level foundtion tht will support the winch nd its lod under ll lod conditions, including shock loding Consult pplicle codes nd regultions for specific rules on instlling the equipment Locte the winch in n re cler of trffic nd ostcles tht could interfere with opertion. Mke sure the winch is ccessile for mintennce nd opertion Mintin fleet ngle etween 1/2 nd 1-1/2 degrees. The proper fleet ngle minimizes wire rope dmge y helping the wire rope wind uniformly onto the drum. See Figure Fsten the winch securely to the foundtion. FOR STANDARD PRODUCTS referred to in this mnul, use 1/2 inch corse thred fsteners, grde 5 or etter, torque dry to 75 ft l without luriction for the M452 series. Use 3/4 inch corse thred fsteners, grde 5 or etter, torque dry to 260 ft l without luriction for M492 series. Mke sure the winch is secured to solid foundtion sed on ccepted engineering prctices. non-stndrd products tht vry from the originl design my hve different fstening requirements. Contct structurl engineer or Thern, Inc. for this informtion. To comply with locl codes, contct qulified professionl to otin proper structure or foundtion specifictions for the mounting of thern products.

5 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge Instlling the Wire Rope Importnt! Use wire rope nd other rigging equipment rted for the size of the lrgest lod you will e moving. Do not drg the wire rope through dirt or deris tht could cuse dmge, or poor opertion. Alwys wer protective clothing when hndling wire rope. Instll the wire rope so it is wound correctly s shown, or the winch will not work properly, nd the lod could escpe. See Figure 3. Instll the wire rope securely to the winch drum. A poorly secured wire rope could come loose from its nchor nd llow the lod to escpe. Do not operte the winch unless the hirpin clip is ssemled to the shft Purchse the proper wire rope for your ppliction. Keep the following in mind when selecting wire rope. Contct reputle wire rope supplier for help. c Breking strength of new wire rope should e t lest 3 times greter thn the lrgest lod plced on the winch. If lods re lifted or pulled on n incline, the reking strength must e t lest 5 times greter thn the lrgest lod. These re minimum vlues nd will vry with the type of lod nd how you re moving it. Wire rope ly must gree with the winding direction of the drum to help insure proper winding. We recommend 7 x 19 glvnized ircrft cle for dimeters up to 5/16 inch, nd 6 x 37 IWRC improved plow steel wire rope for dimeters of up to 3/4 inch. (A mximum rope dimeter of 1/2 inch is recommended due to the drum dimeter.) Importnt! Use sheve or roller guide to direct the wire rope to the drum whenever possile. Instll sheves, trcks nd other equipment so they will remin fixed under ll lod conditions. Follow the recommendtions of the equipment mnufcturer. Use sheves of proper dimeter to minimize wer on the wire rope. Follow the recommendtions of the sheve mnufcturer. Figure 1 Mintining the Fleet Angle When wire rope trvels over sheve or through roller guide mintin fleet ngle y locting the sheve or guide n pproprite distnce from the drum, shown s distnce A. fixed sheve or roller guide distnce A smooth drum 1/2 to 1-1/2 degrees center line When wire rope trvels directly to the lod mintin fleet ngle y controlling sideto-side movement of the lod with trcks or guide rils. Allowing the lod to move too fr to one side cuses stress on the drum flnge which my cuse dmge. lod smooth drum 1/2 to 1-1/2 degrees center line trcks or guide rils

6 pge 6 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches Figure 2 Cotter Pins Instll the hndle. Plce the hndle weldment on the drum shft nd instll the hir pin clip to hold it in plce. The hir pin clip fits in the groove in the drum shft. end rms ck c Loosen the set screws in the hndle weldment, remove the cotter pin from the end of the hndle ssemly nd insert it in the hndle weldment. Adjust hndle length to suit the opertion nd tighten the set screws. Shorten hndle length for light lods or quick opertion. Increse hndle length for hevy lods or slow opertion. Insert the cotter pin in the end of the hndle nd end the rms ck to secure it in plce. See Figure 2. Figure 3 Wire Rope Instlltion instll the wire rope so it is underwound on the drum s shown INSTALL THE HAND WHEEL (Optionl line item offered y Thern). REMOVE THE HAIRPIN CLIP from the end of the drum shft. REMOVE THE HANDLE ASSEMBLY nd the flt hndle weldment from the drum shft. c d e SLIDE THE HAND WHEEL onto the shft until the ger teeth re completely meshed. REPLACE THE HAIRPIN CLIP. KEEP THE HAIRPIN CLIP in plce t ll times to prevent the Hnd Wheel from ccidentlly ecoming disengged from the winch Anchor the wire rope to the winch drum. See Figure 3. Pss the end of the wire rope through the nchor hole, until t lest 1/2 inch of rope extends out the other side. M452 tighten set screw Tighten the set screw until it flttens the wire rope ginst the nchor hole. Use enough force to drive the point of the set screw securely into the wire rope Turn the hndle clockwise to wind wire rope onto the drum. If wire rope unwinds from the drum when the hndle is rotted clockwise, the wire rope is instlled incorrectly. Instll the wire rope correctly efore continuing Wind four full wrps of wire rope onto the drum y operting the winch while holding the wire rope tught. These wrps serve s nchor wrps nd must remin on the drum t ll times. M492

7 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge Generl Theory of Opertion Importnt! Limit nonuniform winding y keeping tension on the wire rope nd y mintining the proper fleet ngle. It is your responsiility to detect nd ccount for different fctors ffecting the condition nd performnce of the equipment The pull required to move the lod must not exceed the lod rting of the winch. Consider the totl force required to move the lod, not the weight of the lod This equipment cn develop forces tht will exceed the lod rting. It is the responsiility of the equipment user to limit the size of the lod. Inspect the equipment regulrly for dmge ccording to the instructions contined in this mnul Use disc rke on ll hnd winches used to lift lods or pull lods on n incline Performnce rtings of the equipment re ffected y the mount of wire rope wound on the drum, the wy in which it is wound, nd the wy the winch is used. c Drum cpcity depends on how tightly nd evenly the wire rope is wound on the drum. Actul drum cpcities re usully 25-30% less thn vlues shown in performnce Tles, due to loose winding nd overlpping. Force required to lift the lod increses with ech dditionl lyer of wire rope wound onto the drum. The vlue shown in performnce Tles is sed on n empty drum, nd mximum hndle length. Lod rting represents the mximum pull tht cn e plced on new equipment. Lod rtings re ssigned vlues for specific mounts of lod trvel or wire rope ccumultion. The lod rting decreses s lyers of wire rope ccumulte on the drum Duty rtings refer to the type of use the equipment is suject to. Consider the following when determining duty rting. c d Environment: hrsh environments include hot, cold, dirty, wet, corrosive, or explosive surroundings. Protect the equipment from hrsh environments when possile. mintennce: poor mintennce, mening poor clening, luriction, or inspection, leds to poor opertion nd possile dmge of the equipment. Minimize poor mintennce y crefully following the instructions contined in this mnul. loding: severe loding includes shock loding nd moving lods tht exceed the lod rting of the equipment. Avoid shock lods, nd do not exceed the lod rting of the equipment. Frequency of Opertion: frequent or lengthy opertions increse wer nd shorten the life spn of gers, erings, nd other components. Increse mintennce of the equipment if used in frequent opertions. Contct the fctory for more informtion.

8 pge 8 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches 2.3 Breking-In the Winch Brek-in occurs during the first 10 hours of norml opertion. During rek-in, mting surfces ecome polished, nd clernces increse. This is desired for efficient opertion of erings nd gers Inspect the winch following rek-in ccording to the Instructions for Periodic Inspection. 2.4 Prepring for Opertion Importnt! When determining whether the lod will exceed the lod rting, consider the totl force required to move the lod Consider the opertion. Do not egin until you re sure you cn perform the entire opertion without hzrd Inspect ll components of the system. Inspect the winch nd other equipment ccording to the Instructions for Frequent Inspection. Opertors must e in good helth, lert, thoroughly trined in operting the equipment, nd properly clothed (hrd ht, sfety shoes nd sfety glsses, no loose clothing). c The lod must e cler of other ojects nd free to move. Mke sure the lod will not tip, spin, roll wy, or in ny wy move uncontrollly Know your lod nd mke sure you do not exceed the lod rting of the winch or ny other equipment in the system. 2.5 Attching the Lod Figure 4 Attching Lod ltch closed tight ginst hook Do not wrp the wire rope round the lod. This dmges the wire rope nd could cuse the lod to escpe. Use sling or other pproved lifting device Cler ojects from the pth of the lod so you cn move it freely nd oserve it t ll times during the opertion Attch the lod using nylon sling, or other pproved lifting device. Follow the recommendtions of the sling mnufcturer. sling seted in sddle of hook Set the sling in the sddle of the hook with the hook ltch completely closed. See Figure 4. Center the lod on the hook so it will remin lnced nd not tip or rotte to one side.

9 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge Moving the Lod Importnt! Oey stop signl from nyone. Mintin tension on the wire rope to keep it tightly nd evenly wound on the drum. If the winch nd lod re not visile during the entire opertion, get help from nother person. Appoint supervisor if more thn one person is involved in the opertion. This will reduce confusion nd increse sfety. When lifting lod, use tg line to keep the lod from swinging or twisting, while keeping yourself wy from the lod. Remove the winch hndle when the winch is not in use, to help void unuthorized use. Do not use the hndle or hnd wheel s rke or nchor for lod Engge the rtchet when winding wire rope onto the drum, disengge the rtchet to unwind the wire rope. Do not engge the rtchet while the winch gers re turning. Stop the winch efore engging the rtchet. Disengge the rtchet y moving the lod slightly to remove pressure from the rtchet, then pull out nd turn the rtchet kno 90 degrees Turn the hndle or Hnd wheel clockwise to wind wire rope onto the drum. If wire rope unwinds from the drum when the hndle is rotted clockwise, the wire rope is instlled incorrectly. Instll the wire rope correctly efore continuing Move the lod slowly nd smoothly, only smll distnce t first. Mke sure the lod is lnced nd securely ttched efore continuing. Mke sure you re not in line with cle movement. Grip the hndle tightly t ll times during opertion. When using the wheel, grip the wheel rim tightly using oth hnds. Do not gr the spokes or rech etween the spokes. c If you relese the hndle or hnd wheel on units not equipped with disc rke, the lod my ckdrive cusing it to spin. Do not try to stop spinning hndle or wheel, step cler until the spinning stops Oserve the wire rope s it winds onto the drum. If it ecomes loose, uneven, or overlpped, stop the opertion nd rewind the wire rope efore continuing. Continued opertion with overlpped or uneven wire rope cn dmge the wire rope nd shorten its life TO QUICKLY WIND OR UNWIND unloded wire rope, move the hndle to or instll the hnd wheel on the countershft. Do not ttempt to move lod with the hndle or hnd wheel instlled on the countershft. When using the hnd wheel, the hirpin clip cnnot e ssemled to the winch. To prevent losing the clip, leve it ttched to the drum shft until you re redy to reposition the hnd wheel ck to the drum shft.

10 pge 10 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches 3.1 Clening the Winch Importnt! Increse the frequency of mintennce procedures if the winch is: Operted for long periods. Used to pull hevy lods. Operted in wet, dirty, hot, or cold surroundings. Clen the winch to remove dirt nd help prevent rust nd corrosion Clen the winch every six months or whenever it is dirty. c Wipe ll equipment to remove dirt nd grese. Leve light film of oil on ll surfces to protect them ginst rust nd corrosion. Wipe off excessive mounts of oil to void the ccumultion of dirt Remove ll unnecessry ojects from the re surrounding the winch. 3.2 Luricting the Winch Importnt! Mke sure luricnt hs temperture rting pproprite for the mient tempertures of the opertion. Luricte the spur gers efore ech opertion, nd periodiclly during opertion. Filure to luricte the gers will cuse dmge or deformtion of ger teeth. Luricte the winch properly to help protect it from wer nd rust. Red the following instructions crefully Consult mnufcturer s recommendtions for specific informtion on luricting the wire rope nd other equipment Luricte winch erings nd shfts t lest every 6 months. c Apply 2 to 3 drops of SAE 30 non-detergent oil to erings nd shfts t ll friction points. Rotte the drum severl times to llow the oil to penetrte, nd wipe off excess oil to void ccumultion of dirt. DO NOT LUBRICATE the hnd wheel when in use. You need it dry for secure grip Luricte winch gers efore every opertion nd t lest every 10 hours during opertion. Apply light film of open ger luricnt to the ger teeth on ll gers. Use Spryon S00201 or equivlent open ger lue. For dirty conditions use dry luricnt such s dry grphite or Moly Luricte the wire rope nd other equipment y following the mnufcturer s recommendtions.

11 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge Inspecting the Equipment Importnt! Strt n inspection progrm s soon s you put the winch into use. Appoint qulified person to e responsile for regulrly inspecting the equipment. Keep written records of inspection. This llows comprison with comments from previous inspections so you cn see chnges in condition or performnce. Perform frequent inspections: Before ech opertion. Every 3 hours during opertion. Whenever you notice signs of dmge or poor opertion. Frequent Wire Rope Inspection: Use ASME B30.7 s guideline for rope inspection, replcement nd mintennce. Check the wire rope, end connections nd end fittings for corrosion, kinking, ending, crushing, irdcging or other signs of dmge. Check the numer, distriution nd type of visile roken wires. See prgrph nd Figure 5. Check the wire rope for reduction of rope dimeter from loss of core support, or wer of outside wires. See Figure 7. Tke extr cre when inspecting sections of rpid deteriortion such s sections in contct with sddles, sheves, repetitive pickup points, crossover points nd end connections. Do not use dmged or mlfunctioning equipment. Plce n OUT OF ORDER sign on the winch. Do not use the winch until the sign is removed y qulified mintennce person who hs completely corrected the prolem. Inspect the winch to detect signs of dmge or poor opertion efore they ecome hzrdous. See Tle Consult pplicle codes nd regultions for specific rules on inspecting the winch nd other equipment Consult mnufcturer s recommendtions for informtion on inspecting the wire rope nd other equipment Instructions for Frequent Inspection Visully inspect the entire winch nd ll other equipment involved in the opertion. Check ll equipment for crcks, dents, ending, rust, wer, corrosion nd other dmge. Mke sure the wire rope is instlled correctly nd nchored securely to the drum. Mke sure the winch is properly luricted. Mke sure the set screws holding the hndle in plce re tight, nd the hir pin clip is instlled. Mke sure mounting fsteners re tightened securely. Mke sure the foundtion is in good condition, nd cple of supporting the winch nd its lod under ll lod conditions. Test winch performnce y moving test lod not exceeding the lod rting. Listen for unusul noises, nd look for signs of dmge s you operte the winch. Mke sure the wire rope winds evenly nd tightly onto the drum. If it is loose or uneven, rewind it efore continuing. Mke sure the hndle rottes freely in oth directions. Mke sure the rtchet engges nd disengges completely. If equipped with rke, check the rke. Rise the lod, then lower it nd stop it few feet off the ground. If the lod continues to cost or creep under norml operting conditions, the rke needs repir or replcement. Contct Thern, Inc. Completely correct ll prolems efore continuing. Use the Trouleshooting Chrt to help determine the cuse of certin prolems. See Tle 2.

12 pge 12 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches Perform periodic inspections: Every 6 months. Whenever you return the winch to service from storge. Whenever you notice dmge or poor opertion in frequent inspection. Whenever you hve, or think you my hve, overloded or shock loded the winch. Figure 5 Broken Wires wire strnd one ly Wire rope ssemly must e replced if more thn 6 wires re roken in one ly, or if more thn 3 wires re roken in one strnd in one ly. Figure 6 Lod Hook Inspection twist throt opening Instructions for Periodic Inspection c Visully inspect the winch nd ll other equipment. Check the finish for wer, flking, or other dmge. Check ll equipment for crcks, dents, ending, rust, wer, corrosion nd other dmge. If the equipment ws overloded, or if you notice crcks or other signs of overloding nd dmge, promptly remove equipment from use nd hve it repired or replced. Do not continue to use dmged or overloded equipment or wire rope. Check ll fsteners for striped threds, wer, ending, nd other dmge. Check the foundtion for crcks, corrosion, nd other dmge. Mke sure the winch is properly luricted. Mke sure ll lels nd pltes re redle, firmly ttched, free of dmge nd clen. Replcements re ville from the fctory. Inspect the wire rope ccording to the wire rope mnufcture's recommendtions or follow ccepted industry stndrds for wire rope inspections. Alwys wer protective clothing when hndling wire rope. Check the entire length of wire rope for ent wires, crushed res, roken or cut wires, corrosion, nd other dmge. Crefully inspect res tht pss over sheves or through roller guides. Note the loction nd concentrtion of roken wires. Replce wire rope if more thn 6 wires re roken in one ly, or more thn 3 wires re roken in one strnd in one ly. See Figure 5. Mke sure the lod hook, nchor fitting or other devices re securely ttched to the wire rope, nd the wire rope where they re ttched is not fryed, corroded, roken, or otherwise dmged. Mesure the throt opening, thickness, nd twist of the hook. Replce the hook if it shows signs of dmge. See Figure 6. Mke sure hook ltch opens without inding nd closes when relesed. Check the nchor holes in the drum nd the surrounding re for signs of wer or distortion. move the drum with your hnds. Check for excessive movement indicting worn or loose gers, erings, or shfts. Slight endply in the driveshft is norml. Excessive movement is cused y overloding or overheting, nd is sign tht your ppliction my require lrger winch. thickness The wire rope ssemly must e replced if the throt opening is 15% wider thn nominl, if the thickness is 10% less thn nominl, or if the hook is twisted 10 or more. d e Plce enough weight to keep the wire rope stright nd tightly drwn. Mesure the dimeter of the wire rope, especilly in res where wer is noticele. Replce the wire rope if the dimeter mesures elow the minimum dimeter t ny point. See Figure 7. Remove the winch from the foundtion. Check fsteners for stripped threds, wer, ends, nd other dmge. Check the frme for ending, distortion, crcks nd other dmge. A ent frme is cused y overloding, nd is sign tht your ppliction my require winch with lrger lod rting.

13 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge 13 Figure 7 Rope Dimeter correct dimeter incorrect The wire rope ssemly must e replced if the dimeter mesures less thn the minimum dimeter t ny point. wire rope size minimum dimeter 1/8 in 7/64 in (.1094 in) 3/16 in 11/64 in (.1719 in) 1/4 in 15/64 in (.2344 in) 5/16 in 19/64 in (.2969 in) 3/8 in 11/32 in (.3438 in) 1/2 in 15/32 in (.4688 in) 5/8 in 37/64 in (.5781 in) 3/4 in 45/64 in (.7031 in) f Test winch performnce y operting the winch with lod equl to the lod rting. Listen for unusul noises, nd look for signs of dmge s you operte the winch. Mke sure the wire rope winds evenly nd tightly onto the drum. If it is loose or uneven, rewind it efore continuing. Oserve the rotting drum, look for signs of loose or misligned erings. Mke sure the lod moves smoothly, without hesittion or strin. Mke sure the hndle rottes freely in oth directions. Mke sure the rtchet engges nd disengges completely. If equipped with rke, check the rke. Rise the lod, then lower it nd stop it few feet off the ground. If the lod continues to cost or creep under norml operting conditions, the rke needs repir or replcement. Contct Thern, Inc. Completely correct ll prolems efore continuing. Use the trouleshooting chrt to help determine the cuse of certin prolems. See Tle 2. Tle 1 Inspection Checklist checked oxes indicte dmge or prolem in need of repir dmges prolems generl finish wethered, flking, otherwise dmged winch jerks or hesittes during opertion prts crcked, ent, rusted, worn, otherwise dmged unusul noises, other signs of mlfunction fsteners stripped threds, ent, worn, otherwise dmged loose, not tightened to proper torque gers excessively worn, crcked, corroded, otherwise dmged loose or improperly luricted rtchet rtchet corroded, crcked, worn, otherwise dmged rtchet does not engge or disengge rke ssemly rke corroded, crcked, worn, otherwise dmged rke does not operte properly drum nchor hole worn, distorted, otherwise dmged excessive movement or cklsh wire rope ent, crushed, otherwise dmged wire rope loosely or unevenly wound roken wires, see Figure 5 replce if more thn 6 wires in one ly, numer per strnd = or 3 wires in one strnd in one ly, re roken numer per ly = dimeter reduced, see Figure 7 replce if dimeter is excessively worn dimeter = end connections corroded, rusted, worn, otherwise dmged not securely ttched lod hook twisted, ent, worn, otherwise dmged, see Figure 6 hook ltch fils to close when relesed replce if twist is 10 degrees or more twist = replce if throt width is 15% lrger thn nominl throt width = replce if thickness is 10% less thn nominl thickness = lels nd pltes dirty, illegile, otherwise dmged loosely ttched or missing comments: uthorized signture: dte

14 pge 14 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches Tle 2 Trouleshooting Chrt Contct the fctory for detiled instructions if you re required to disssemle the winch or rke for ny reson. Disssemly of the winch or rke efore contcting Thern, Inc. voids ll wrrnties. prolem cuse correction hndle turns, drum doesn't turn loose or roken spring pins...inspect winch nd rke, repir s necessry loose, stripped or roken gers...inspect gers nd repir s necessry hndle turns hrd or not t ll rtchet on winch engged...disengge winch rtchet lod too hevy...lighten lod spring pins loose or roken on winch or rke...inspect winch nd rke, repir s necessry disc rke dmged or locked...inspect rke, repir s necessry gers or erings roken or locked...inspect nd repir s necessry rke does not operte properly friction discs worn or dmged...inspect nd replce s necessry friction discs dmged from over luriction...inspect nd replce s necessry disc rke rtchet pwl dmged...inspect nd repir s necessry excessively worn gers or erings lod too hevy...lighten lod (excessive cklsh) poor luriction of gers or erings...inspect nd reluricte s necessry overheting operted too long without rest...llow to cool lod too hevy...lighten lod poor luriction...inspect nd luricte s necessry ering seized up...inspect nd replce s necessry unusul noises high pitched squek poor luriction...inspect nd reluricte s necessry grinding noise contminted luriction...clen nd reluricte winch dirt in rke or winch gers...inspect nd clen s necessry roken gers or erings...inspect nd replce s necessry rttling noise loose olts, set screws or other fsteners...tighten ll olts nd other fsteners uneven clicking noise in rke roken ger tooth in rke...inspect nd repir s necessry wek clicking noise in rke spring or rtchet pwl dirty or dmged...inspect nd clen or repir s necessry worn rke rtchet pwl, ger, or spring...inspect nd replce s necessry no clicking noise in rke rtchet incorrectly instlled...disssemle nd instll correctly rtchet pwl dmged or worn excessively...inspect nd replce s necessry

15 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge Repiring the Winch Importnt! It is your responsiility to determine when to replce prts. When considering whether to continue using prt or to replce it, rememer tht replcing it is the est wy to void further equipment dmge. Replce ll spring pins nd retining rings when you disssemle the winch or rke for repir or replcement. Appoint qulified person to e responsile for ll repirs to the equipment Get fctory uthoriztion for ll repirs. Unuthorized repirs will void the wrrnty, nd my led to dmge or filure of the winch Replce dmged or poorly operting prts with Thern repir prts Refinish res where the pint is worn or flking. A good finish helps to protect ginst corrosion nd wether dmge. c Remove the finish from dmged res, down to the re metl. Clen the re thoroughly. Repint with high qulity primer nd finishing cot To order repir prts, contct your locl deler. Include the following informtion when ordering: model numer seril numer (or code numer) prt numer dte purchsed, nd from whom description of wht hppened, or wht is wrong your nme nd return ddress 4.1 Trnsporting the Winch Importnt! Keep record of wht you ship, nd when you send it Pck the winch using the originl pckging mterils, if possile Sel the winch in plstic with desiccnt to help protect it from rust, corrosion, nd other dmge Inspect the winch ccording to the Instructions for Periodic Inspection efore instlling it in new loction. 4.2 Storing the Winch Sel the winch in plstic with desiccnt to help protect it from rust, corrosion, nd other dmge Store the winch in cool clen plce wy from corrosive chemicls nd moisture Rotte the drum periodiclly to keep ering nd gers surfces from ecoming lcquered Inspect the winch ccording to the Instructions for Periodic Inspection efore instlling it for opertion.

16 pge 16 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches Spur Ger Hnd Winch Model M452 item description prt numer qty. 1 DRUM C FRAME D HEX JAM NUT NYLK NC SST A CAPSCREW HEXHD NC X.625 SST A BEARING HOUSING ASSEMBLY A COUNTERSHAFT B RADIAL BALL BEARING 1.00ID X 2.00OD X.75 STL A RETAINING RING EXT SST A PINION 2.25OD X 2.0PD X 1.71RD A SET SCREW SOKHD NYLK NC X.250 SST A KEY.250 X.250 X A KEY.250 X.250 X A COUNTERSHAFT GEAR C SET SCREW SOKHD NYLK NC X.625 SST A FLAT HANDLE ASSEMBLY B HAIR PIN CLIP.750 X.093 DIA SST A DRUM SHAFT B COTTER PIN.187 X SST A HANDLE ASSEMBLY B RATCHET PIN A SLOTTED SPRING PIN.156 X.750 SST A COMPRESSION SPRING.658OD X.048WD X SST A RATCHET PIN KNOB A SLOTTED SPRING PIN.156 X SST A SET SCREW SQHD NC X.500 SST A HANDLE GRIP A BRAKE HANDLE B BRAKE BAND ASSEMBLY C FLAT WASHER SMALL OD.312 X.750 SST A WASHER HELSPRLK.312 X.596 X.078 SST A BRAKE HANDLE BUSHING A HEX NUT NC SST A LABEL LOAD RATING A LABEL CAUTION A LABEL CODE LABEL WARNING A LABEL OIL A LABEL CABLE TAKEUP A LABEL WARNING A2691 1

17 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge

18 pge 18 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches Spur Ger Hnd Winch Model M452B 1 item description prt numer qty. 1 DRUM C FRAME D HEX JAM NUT NYLK NC SST A CAPSCREW HEXHD NC X.625 SST A DRUM SHAFT B BEARING HOUSING ASSEMBLY A COUNTER SHAFT B BALL BEARING RAD 1.00ID X 2.00OD X.75 STL A RETAINING RING EXT SST A PINION A SET SCREW SOKHD NYLK NC X.250 SST A KEY.250 X.250 X A KEY.250 X.250 X A COUNTERSHAFT GEAR C SET SCREW SOKHD NYLK NC X.625 SST A BRAKE SUBASSEMBLY C HANDLE ASSEMBLY B COTTER PIN.187 X SST A RATCHET PIN A SLOTTED SPRING PIN.156 X.750 SST A COMPRESSION SPRING.658OD X.048WD X SST A RATCHET PIN KNOB A SLOTTED SPRING PIN.156 X SST A HAIR PIN CLIP.750 X.093 DIA SST A LABEL LOAD RATING A LABEL CAUTION A LABEL CODE LABEL WARNING A LABEL OIL A LABEL CABLE TAKEUP A See Hnd Operted Disc Brke mnul (A6191) for rke informtion.

19 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge

20 pge 20 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches Spur Ger Hnd Winch Model M452B-A 1 item description prt numer qty. 1 DRUM C FRAME D HEX JAM NUT NYLK NC SST A CAPSCREW HEXHD NC X.625 SST A SET SCREW SOKHD NYLK NC X.625 SST A BRAKE SUBASSEMBLY C HANDLE ASSEMBLY B COTTER PIN.187 X SST A BEARING HOUSING ASSEMBLY A DRUM SHAFT B BALL BEARING RAD 1.00ID X 2.00OD X.75 STL A COUNTER SHAFT B RETAINING RING EXT SST A KEY.250 X.250 X A PINION 2.25OD X 2.0PD X 1.71RD A SET SCREW SOKHD NYLK NC X.250 SST A KEY.250 X.250 X A COUNTERSHAFT GEAR C HAIR PIN CLIP.750 X.093 DIA SST A LABEL LOAD RATING A LABEL CAUTION A LABEL CODE LABEL WARNING A LABEL OIL A LABEL CABLE TAKEUP A See Hnd Operted Disc Brke mnul (A6191) for rke informtion.

21 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge

22 pge 22 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches Spur Ger Hnd Winch Model M492 Model M item description prt numer qty. prt numer qty. 1 FRAME D SD RADIAL BALL BEARING A A COUNTERSHAFT B SB RETAINING RING EXT SST A A MACHINERY BUSHING X X 18GA A A SET SCREW SOKHD NYLK NC X.500 SST A A SET SCREW SOKHD NYLK NC X.625 SST A A SET SCREW SOKHD NYLK NC X SST A A DRUM SHAFT B SB BEARING HOUSING ASSEMBLY B B MACHINERY BUSHING X X 18GA A A DRUM C SC BEARING HOUSING ASSEMBLY B B FLAT HANDLE ASSEMBLY B B HANDLE ASSEMBLY B B COTTER PIN.187 X SST A A HAIR PIN CLIP.750 X.093 DIA SST A A BRAKE HANDLE BUSHING A A CAPSCREW HEXHD NC X SST A A HEX NUT NC SST A A FLAT WASHER SMALL OD.312 X.750 SST A A WASHER HELSPRLK.312 X.596 X.078 SST A A SLOTTED SPRING PIN.187 X.750 SST A A COUNTERSHAFT GEAR C C KEY.250 X.250 X A A RATCHET PIN A A RATCHET PIN KNOB A A COMPRESSION SPRING.658OD X.048WD X SST A A SLOTTED SPRING PIN.156 X.750 SST A A SLOTTED SPRING PIN.156 X SST A A PINION A A SET SCREW SOKHD NYLK NC X.250 SST A A KEY.250 X.250 X A A SET SCREW SQHD NC X.750 SST A A HANDLE GRIP A A BRAKE HANDLE B B BRAKE BAND ASSEMBLY B B LABEL LOAD RATING A A LABEL CAUTION A A LABEL CODE LABEL WARNING A A LABEL OIL A A LABEL CABLE TAKEUP A A LABEL WARNING A A For use with wire rope greter thn 9/16 inch. 2 For use with 9/16 inch wire rope or smller.

23 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge

24 pge 24 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches Spur Ger Hnd Winch Model M492B 1 Model M492B-12 1 item description prt numer qty. prt numer qty. 1 FRAME D SD RADIAL BALL BEARING A A COUNTERSHAFT B SB RETAINING RING EXT SST A A MACHINERY BUSHING X X 18GA ZPLIRDI ST A A SET SCREW SOKHD NYLK NC X.500 SST A A SET SCREW SOKHD NYLK NC X.625 SST A A SET SCREW SOKHD NYLK NC X SST A A DRUM SHAFT B SB BEARING HOUSING ASSEMBLY B B MACHINERY BUSHING X X 18GA ZPLIRDI ST A A DRUM C SC BEARING HOUSING ASSEMBLY B B COUNTERSHAFT GEAR C C KEY.250 X.250 X A A RATCHET PIN A A RATCHET PIN KNOB A A COMPRESSION SPRING.658OD X.048WD X SST A A SLOTTED SPRING PIN.156 X.750 SST A A SLOTTED SPRING PIN.156 X SST A A PINION A A SET SCREW SOKHD NYLK NC X.250 SST A A KEY.250 X.250 X A A BRAKE SUBASSEMBLY C C HANDLE ASSEMBLY B B COTTER PIN.187 X SST A A HAIR PIN CLIP.750 X.093 DIA SST A A LABEL LOAD RATING A A LABEL CAUTION A A LABEL CODE LABEL WARNING A A LABEL OIL A A LABEL CABLE TAKEUP A A See Hnd Operted Disc Brke mnul (A6191) for rke informtion. 2 For use with wire rope greter thn 9/16 inch. 3 For use with 9/16 inch wire rope or smller.

25 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge

26 pge 26 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches Spur Ger Hnd Winches Performnce Chrcteristics 3 lod rting (l) wire drum cpcity (ft) 1 single doule force 2 model 1st mid full rope 1st mid full ger ger to lift numer description lyer drum drum di. (in) lyer drum drum rtio rtio 1000 l M l mrine duty / : :1 10 l (for pulling only) 5/ (doule ger) 3/ M452B 4000 l mrine duty / :1 10 l with rke (for lifting) 5/ (doule ger) 3/ M452B-A 4000 l mrine duty / :1 10 l with rke (for lifting) 5/ (doule ger) 4 inch drum width 3/ M492 10,000 l mrine duty 10, / : :1 8 l (for pulling only) 3/ (doule ger) 1/ M492B 10,000 l mrine duty 10, / :1 8 l with rke (for lifting) 3/ (doule ger) 1/ M ,000 l mrine duty 10, / : :1 8 l (for pulling only) 3/ (doule ger) 12 inch drum width 1/ M492B-12 10,000 l mrine duty 10, / :1 8 l with rke (for lifting) 3/ (doule ger) 12 inch drum width 1/ Actul drum cpcities my e 25-30% less, due to nonuniform winding. Wire rope tension will lso ffect drum cpcity. 2 Approximte hndle force required to lift 1000 l with n empty drum, nd mximum hndle length. 3 Performnce Chrcteristics re for stndrd products referred to in this mnul. Non-stndrd products my vry from the originl design. Contct Thern, Inc. for this informtion. Hnd Wheel Model HW452 Model HW492 item description prt numer qty. prt numer qty. 1 HAND WHEEL C C BEARING SLEEVE A A BEARING SLEEVE A A LABEL CODE NUMBER LABEL MODEL A A LABEL WARNING A A These items re not shown in prts drwing

27 Owner's Mnul for Thern M452 nd M492 Series Hnd Winches pge 27 NOTES:

28 Thern, Incorported 5712 Industril Prk Rod Winon, MN PH FAX Thern Europe Windmolen NN Almelo Netherlnds PH

Owner s Manual For 5122 Series Portable Davit Cranes ORIGINAL TEXT

Owner s Manual For 5122 Series Portable Davit Cranes ORIGINAL TEXT Red this Owner s Mnul thoroughly efore operting the equipment. Keep it with the equipment t ll times. Replcements re ville from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com IMPORTANT:

More information

Owner s Manual For 4WM2 Series Worm Gear Hand Winch ORIGINAL TEXT

Owner s Manual For 4WM2 Series Worm Gear Hand Winch ORIGINAL TEXT Red this Owner s Mnul thoroughly efore operting the equipment. Keep it with the equipment t ll times. Replcements re ville from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com IMPORTANT:

More information

Owner s Man ual. For 4HPF/4HWF/4HBP Series Helical/Parallel, Helical/Worm, Helical/Bevel and Planetary Gear Power Winches

Owner s Man ual. For 4HPF/4HWF/4HBP Series Helical/Parallel, Helical/Worm, Helical/Bevel and Planetary Gear Power Winches Red this Own er s Mn u l thor ough ly e fore op er t ing the equip ment. Keep it with the equip ment t ll times. Re plce ments re vil le from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com

More information

Owner s Manual For TAC Series Planetary Gear Air Winches ORIGINAL TEXT

Owner s Manual For TAC Series Planetary Gear Air Winches ORIGINAL TEXT Red this Owner s Mnul thoroughly efore operting the equipment. Keep it with the equipment t ll times. Replcements re ville from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com IMPORTANT:

More information

Owner s Man ual. For MTA1000 and MTA2000 Series Cycloidal Gear Air Winches

Owner s Man ual. For MTA1000 and MTA2000 Series Cycloidal Gear Air Winches Red this Own er s Mn u l thor ough ly e fore op er t ing the equip ment. Keep it with the equip ment t ll times. Re plce ments re vil le from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com

More information

Owner s Manual. For TH330MR1 Hydraulic Winches Dedicated for Personnel Lifting

Owner s Manual. For TH330MR1 Hydraulic Winches Dedicated for Personnel Lifting Red this Owner s Mnul thoroughly before operting the equipment. Keep it with the equipment t ll times. Replcements re vilble from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com IMPORTANT:

More information

Workfit -SR, Dual Monitor Short Surface

Workfit -SR, Dual Monitor Short Surface User's Guide Workfit -SR, Dul Monitor Short Surfce Do not throw wy! Crdord locks needed for instlltion. Visit http://www.ergotron.com/workfi t-sr-instll for instlltion instructionl video. NOTE: 10 feet

More information

400 Series Flat Panel Monitor Arm Rotate Mount Double Pivot P/L

400 Series Flat Panel Monitor Arm Rotate Mount Double Pivot P/L User's Guide 400 Series Flt Pnel Monitor Arm Rotte Mount Doule Pivot P/L < 23ls. (10.44 kg) For the ltest User Instlltion Guide plese visit: www.ergotron.om 1 of 10 Hzrd Symols Review These symols lert

More information

Reproduction. Not for. Mower - Roller Bar WARNING. Installation and Leveling Instructions. Attention Setup Personnel: Model: ,

Reproduction. Not for. Mower - Roller Bar WARNING. Installation and Leveling Instructions. Attention Setup Personnel: Model: , Mower - Roller Br Instlltion nd Leveling Instructions 4 Model: 9555, 9594 Attention Setup Personnel: 5 4 5 Model: 958, 9595 Model: 9559 Model: 959 The sfety wrnings provided in this guide nd in the trctor's

More information

Lesson 8: Application Technology

Lesson 8: Application Technology The type of ppliction equipment used must suit the type of ppliction. In this module, you ll lern the prts of the most common types of ppliction equipment used by ssistnt pplictors, s well s how to properly

More information

VB-7253 Series. Application. Features. Applicable Literature

VB-7253 Series. Application. Features. Applicable Literature VB-7253 Series 1/2 to 2 Screwed NPT Stinless Steel Trim with Teflon Disc Stem Up Open, Two-Wy Vlves Generl Instructions Appliction VB-7253 series single set, stem down to close, two wy vlves control wter

More information

pge 2 Owner's Mnul for Thern 4WS nd 4HS Series Power Winhes Two-Yer Limited Wrrnty Plese reord the following: Dte Purhsed: Model No.: Seril No.: This

pge 2 Owner's Mnul for Thern 4WS nd 4HS Series Power Winhes Two-Yer Limited Wrrnty Plese reord the following: Dte Purhsed: Model No.: Seril No.: This Red this Own er s Mn u l thor ough ly e fore op er t ing the equip ment. Keep it with the equip ment t ll times. Re ple ments re vil le from Thern, In. IMPORTANT: Plese reord produt informtion on pge 2.

More information

First Aid in School Policy

First Aid in School Policy First Aid in School Policy Approved y the Governing Body of West Monkton Church of Englnd Primry School: Reviewed y Governors nd Agreed: Septemer 2017 At West Monkton we im to e n inspirtionl community,

More information

SETUP & PREPARATION KNOW YOUR PRODUCT 1. ASSEMBLY CORDLESS POLE PRUNER. Fitting Rear Handle

SETUP & PREPARATION KNOW YOUR PRODUCT 1. ASSEMBLY CORDLESS POLE PRUNER. Fitting Rear Handle STANDARD EQUIPMENT Pole Chin Guide Br CORDLESS POLE PRUNER Guide Br Cover INSTRUCTION MANUAL Rer Hndle SPECIFICATIONS Input: Br Length: Cutting Length Mx.: Chin Speed: Oil Tnk Cpcity: Length: Weight: 18V

More information

* LANDING ROLLED CURB SIDEWALK RAMP TYPE R (ROLLED SIDES) * LANDING ** RAMP FULL CURB HEIGHT MAY BE REDUCED TO ACCOMMODATE MAXIMUM SIDE FLARE SLOPE

* LANDING ROLLED CURB SIDEWALK RAMP TYPE R (ROLLED SIDES) * LANDING ** RAMP FULL CURB HEIGHT MAY BE REDUCED TO ACCOMMODATE MAXIMUM SIDE FLARE SLOPE * MXIMUM LNDING IS 2.0% IN ECH DIRECTION OF TRVEL. LNDING MINIMUM DIMENSIONS 5' x 5'. ** MXIMUM RMP CROSS IS 2.0%, RUNNING 5% - 7% (8.3% MXIMUM). "NON-WLKING" RE * LNDING 24" CROSS FULL WIDTH PERMNENT

More information

How To Demonstrate Guide E24 & E26

How To Demonstrate Guide E24 & E26 Pre-Demonstrtion Checklist Clen the entire mchine Chrge tteries Check squeegee ldes Bring proper rushes nd/or pds Clening cost nlysis Prepre quottion with lese pyments E24 & E26 literture nd fct sheet

More information

Pinpoint GPS. FCC and IC Compliance Statement

Pinpoint GPS. FCC and IC Compliance Statement FCC nd IC Complince Sttement PINPOINT KEY FOB, FCC ID MVU10148 ACMA: N2523 IC: 6094A 09291, 6094A 09305 This device complies with prt 15 of the FCC Rules. Opertion is suject to the following two conditions:

More information

DBI SALA Confined Space Rescue Davit System

DBI SALA Confined Space Rescue Davit System Instructions for the following series products: Rescue Davit System (See back page for specific model numbers.) User Instruction Manual For Davit Rescue System This manual should be used as part of an

More information

Contents TRIGONOMETRIC METHODS PROBABILITY DISTRIBUTIONS

Contents TRIGONOMETRIC METHODS PROBABILITY DISTRIBUTIONS ontents UNIT 7 TRIGONOMETRI METHODS Lesson 1 Trigonometric Functions................... 462 1 onnecting ngle Mesures nd Liner Mesures.............. 463 2 Mesuring Without Mesuring.........................

More information

Operation Maintenance Installation Warranty Manual

Operation Maintenance Installation Warranty Manual Opertion Mintennce Instlltion Wrrnty Mnul 2017 Mercury Mrine Xi3 Wireless Edition ORIGINAL LANGUAGE INSTRUCTIONS FCC nd IC Complince Sttement Xi SERIES WIRELESS FOOT PEDAL FCC ID MVU09291 Xi SERIES WIRELESS

More information

Grand Espresso Corner Kitchen

Grand Espresso Corner Kitchen Please retain this information for future reference PRTS LIST To order replacement parts, please visit 1 2 3 4 6 5 7 8 9 10 11 12 13 19 22 16 17 18 20 23 24 25 14 15 21 26 28 30 31 32 33 29 34 36 37 27

More information

User Instruction Manual For Davit Rescue System

User Instruction Manual For Davit Rescue System Instructions for the following series products: Rescue Davit System Model numbers 8004000 and 8302500 User Instruction Manual For Davit Rescue System This manual should be used as part of an employee training

More information

ARIAKON OWNER S MANUAL READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS PAINTBALL MARKER.

ARIAKON OWNER S MANUAL READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS PAINTBALL MARKER. RIKON Thank You for choosing RIKON SIM-5 SERIES.68 CLIER PINTLL MRKER (SIM-5. SIM-5 PRO, SIM-5 PRO ELITE) RIKON 2794 LOKER VE WEST SUITE 107 CRLSD C 92010 1-877-4-RIKON 760-268-0735 FX 760-268-0736 On

More information

ANATOMY OF A TRIPOD: Friction Lock (column) 8 Boots / Footwear. Friction Lock (Leg)

ANATOMY OF A TRIPOD: Friction Lock (column) 8 Boots / Footwear. Friction Lock (Leg) IMPORTANT DO NOT USE YOUR TRIPOD UNTIL YOU HAVE READ THESE INSTRUCTIONS. NO WARRANTY CLAIM WILL BE ENTERED INTO FOR THE MISUSE OR INCORRECT USE OF THESE PRODUCTS. ANATOMY OF A TRIPOD: We offer the three

More information

X5-55/X5-70/X5-80/X Operation Maintenance Installation Warranty Manual

X5-55/X5-70/X5-80/X Operation Maintenance Installation Warranty Manual X5-55/X5-70/X5-80/X5-105 Opertion Mintennce Instlltion Wrrnty Mnul EU Complince Sttement Attwood Corportion hereby declres tht the MotorGuide X5 trolling motor is in complince with the essentil requirements

More information

CAUTION - PUT SAFETY FIRST

CAUTION - PUT SAFETY FIRST www.shoremaster.com DVS Vertical Lift (Double V Side): Frame ssembly Instructions. Models: 500DVS - 0ft Wide, 5000lb Capacity - Part #: 0079 600DVS - 0ft Wide, 6000lb Capacity - Part #: 0033.. 3.. 5. CUTION

More information

* SEE ANCHOR SCHEDULE SHEET 7

* SEE ANCHOR SCHEDULE SHEET 7 "-20 MLE PNELMTE W/ WINGNUT -1/2" O.C. "-20 X 1/2" MCHINE OLT & NUT -1/2" O.C 04/0/15 JH UPDTE TO 5TH EDITION (2014) FC 8/14/1 Y DTE SPCING ERROR OR MSONRY POWERS CLK-IN W/ "-20 SIDEWLK OLT -1/2" O.C.

More information

DLx1200, DLx1500, DLx1900, DLx2300 PULLING WINCHES. U.S. Patent Canadian Patent Model #DLx1200

DLx1200, DLx1500, DLx1900, DLx2300 PULLING WINCHES. U.S. Patent Canadian Patent Model #DLx1200 DLx1200, DLx1500, DLx1900, DLx2300 PULLING WINCHES U.S. Patent 6116580 Canadian Patent 2378538 Model #DLx1200 WARNING READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL, OPERATE OR SERVICE THIS WINCH.

More information

Pinpoint GPS 90-8M

Pinpoint GPS 90-8M FCC nd IC Complince Sttement PINPOINT KEY FOB, FCC ID MVU10148 ACMA: N2523 IC: 6094A 09291, 6094A 09305 This device complies with prt 15 of the FCC Rules. Opertion is suject to the following two conditions:

More information

Bypass Compensator Cartridge, Size 16

Bypass Compensator Cartridge, Size 16 Bypss Compenstor Crtridge, Size 6 Q mx = 5 l/min, p mx = 42 br Direct cting, djustble compenstor spring Description These direct-cting bypss pressure-compenstor (hydrostt) crtridges, series DWDP-2B -6,

More information

Pool Ladder. Owner s Manual For: 36in (91 cm), 42in (107 cm), 48in (122 cm) models. For illustrative purposes only.

Pool Ladder. Owner s Manual For: 36in (91 cm), 42in (107 cm), 48in (122 cm) models. For illustrative purposes only. (), 2, 8 1-SECTION OL LDDER ENGLISH 7. X 10. PNTONE 29U 0/1/2017 English OWNER S MNUL IMRTNT SFETY RULES Read, Understand, and Follow all Instructions Carefully before Installing and using this Product.

More information

Hot-Air Blowers 12 / / Hot-Air Blowers

Hot-Air Blowers 12 / / Hot-Air Blowers Hot-Air Blowers MISTRAL HOTWIND PREMIUM / HOTWIND SYSTEM MISTRAL Accessories HOTWIND Accessories VULCAN SYSTEM VULCAN SYSTEM Accessories IGNITER BM4/BR4 IGNITER BM4/BR4 Accessories 12 / 13 14 / 15 16 17

More information

YEARS SKIBOCK CONSTRUCTION MANUAL cm / inch 90kg / 198 lbs 1.5 hours. Length Max weight Time to build

YEARS SKIBOCK CONSTRUCTION MANUAL cm / inch 90kg / 198 lbs 1.5 hours. Length Max weight Time to build SKIOCK CONSTRUCTION MNUL 8 YERS Length Max weight Time to build 130-190 cm / 51-75 inch 90kg / 198 lbs 1.5 hours WRNING - IMPORTNT NOTICE TO PRENTS efore you start constructing and use our product, please

More information

Pool Ladder. Owner s Manual For: 52in (132 cm) model. For illustrative purposes only. Pool is not provided.

Pool Ladder. Owner s Manual For: 52in (132 cm) model. For illustrative purposes only. Pool is not provided. () 52 2-SECTIONS POOL LDDER ENGLISH 7.5 X 10.3 PNTONE 295U 0/17/201 OWNER S MNUL Pool Ladder Owner s Manual For: 52in (132 cm) model For illustrative purposes only. Pool is not provided. IMPORTNT SFETY

More information

THERMOFLO FLUID PUMPS& SYSTEMS THERMOFLO FOR HEATING, COOLING AND WATER SUPPLY APPLICATIONS TO BS7074 SEALED SYSTEMS EXPANSION VESSELS PRESSURIZERS

THERMOFLO FLUID PUMPS& SYSTEMS THERMOFLO FOR HEATING, COOLING AND WATER SUPPLY APPLICATIONS TO BS7074 SEALED SYSTEMS EXPANSION VESSELS PRESSURIZERS THERMOFLO S E A L E D S Y S T E M S THERMOFLO SEALED SYSTEMS FOR HEATING, COOLING AND WATER SUPPLY APPLICATIONS TO BS7074 EXPANSION VESSELS PRESSURIZERS PUMPS& SYSTEMS WALL OR BASE MOUNTING PRESSURIZERS

More information

Pool Ladder. Owner s Manual For: 52" (132 cm) model. For illustrative purposes only.

Pool Ladder. Owner s Manual For: 52 (132 cm) model. For illustrative purposes only. () 52 2-SECTIONS OL LDDER ENGLISH 7.5 X 10.3 PNTONE 295U 05/20/2017 OWNER S MNUL Pool Ladder Owner s Manual For: 52" (132 cm) model For illustrative purposes only. IMRTNT SFETY RULES Read, understand,

More information

TWO BIKE UPRIGHT ROOF MOUNT BIKE CARRIER

TWO BIKE UPRIGHT ROOF MOUNT BIKE CARRIER TWO IKE UPRIGT ROOF OUNT IKE CRRIER NOTE: Please read instructions carefully before installation. Please refer to assembly instructions, and ensure the bike carrier is installed correctly. Please keep

More information

INVESTIGATION 2. What s the Angle?

INVESTIGATION 2. What s the Angle? INVESTIGATION 2 Wht s the Angle? In the previous investigtion, you lerned tht when the rigidity property of tringles is comined with the ility to djust the length of side, the opportunities for useful

More information

Firearm Safety. Links to Topics below XAVIER BECERRA THE SIX BASIC GUN SAFETY RULES. Attorney Genera] The. Six Basic Gun Safety Rules

Firearm Safety. Links to Topics below XAVIER BECERRA THE SIX BASIC GUN SAFETY RULES. Attorney Genera] The. Six Basic Gun Safety Rules firerm Sfety Stte of Cliforni - Deprtment of Justice - Office of the Attorney Generl Pge 1 of 14 Stte of Cliforni Deprtment of]ustice XAVIER BECERRA Attorney Gener] Serch Trnslte Website Trducir Sitio

More information

T POOL ASSEMBLY AND INSTALLATION MANUAL. Trinidad LX Above Ground 52 Round Extruded Wall Pools

T POOL ASSEMBLY AND INSTALLATION MANUAL. Trinidad LX Above Ground 52 Round Extruded Wall Pools T3668-80 POOL SSEMLY ND INSTLLTION MNUL Trinidad LX bove Ground 52 Round Extruded Wall Pools Note: Deck and fence accessories shown are optional. THIS MNUL EXPLINS THE CORRECT METHOD TO SSEMLE YOUR NEW

More information

OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP40M-12 and all WIDE DRUM variations of this HAND OPERATED WINCH.

OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP40M-12 and all WIDE DRUM variations of this HAND OPERATED WINCH. W. W. Patterson Company 3 Riversea Road Pittsburgh, PA 15233 Phone: 800-322-2018 FAX: 412-322-2785 OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP40M-12 and all WIDE DRUM variations of this HAND OPERATED WINCH.

More information

UNIFORM STANDARD DRAWINGS CLARK COUNTY AREA, NEVADA YEAR 2016 REVISIONS

UNIFORM STANDARD DRAWINGS CLARK COUNTY AREA, NEVADA YEAR 2016 REVISIONS , NEVD YER 2016 REVISIONS DWG NO. TITLE ND REVISIONS SUMMRY EFFECTIVE DTE 223.1 Residential Driveway without djacent Sidewalk 7/1/2016 New Drawing to allow flexibility in Roadway Design. 234.1 Typical

More information

VL SHEAVES/CABLE UPGRADE KIT INSTRUCTIONS

VL SHEAVES/CABLE UPGRADE KIT INSTRUCTIONS VL SHEAVES/CABLE UPGRADE KIT INSTRUCTIONS RGC MARINE PRODUCTS BUFFALO, NY P/N 6112062 02/03/17 TABLE OF CONTENTS CHAPTER TITLE PAGE 1 SAFETY... 1 1.1 Introduction... 1 1.2 Safety Definitions... 1 1.3 Equipment

More information

10mm SHOWER PANEL SIZES 1000 & 1200 SIZES 500, 600, 700, 800 & 900 SIZES 1000 & 1200 OPTION 1 - PAGES 2-4 OPTION 2 - PAGES 2-5 OPTION 3 - PAGES 6-7

10mm SHOWER PANEL SIZES 1000 & 1200 SIZES 500, 600, 700, 800 & 900 SIZES 1000 & 1200 OPTION 1 - PAGES 2-4 OPTION 2 - PAGES 2-5 OPTION 3 - PAGES 6-7 SHOWER PANEL 785 / Issue / 5 SIZES 5, 6, 7, 8 & 9 SIZES & SIZES & OPTION - PAGES - OPTION - PAGES - 5 OPTION 3 - PAGES 6-7 Plese red these instrutions refully nd keep for future referene. Inorret fitting

More information

Rules of Hockey including explanations. Effective from 1 January 2015

Rules of Hockey including explanations. Effective from 1 January 2015 Rules of Hockey including explntions Effective from 1 Jnury 2015 Copyright FIH 2014 The Interntionl Hockey Federtion Rue du Vlentin 61 CH 1004 Lusnne Switzerlnd Tel. : + 41 21 641 0606 Fx : + 41 21 641

More information

ERRATA for Guide for the Development of Bicycle Facilities, 4th Edition (GBF-4)

ERRATA for Guide for the Development of Bicycle Facilities, 4th Edition (GBF-4) Dvid Bernhrdt, P.E., President Commissioner, Mine Deprtment of Trnsporttion Bud Wright, Executive Director 444 North Cpitol Street NW, Suite 249, Wshington, DC 20001 (202) 624-5800 Fx: (202) 624-5806 www.trnsporttion.org

More information

CATERPILLAR XL G2 YEARS CONSTRUCTION MANUAL

CATERPILLAR XL G2 YEARS CONSTRUCTION MANUAL 6-14 CTERPILLR XL G2 YERS CONSTRUCTION MNUL Length Max weight Time to build 120-168 cm / 47-66 inch 70 kg / 153 lbs 2 hours WRNING - IMPORTNT NOTICE TO PRENTS efore you start constructing and use our product,

More information

USA Field Hockey s Modifications to the 2017 FIH Rules of Hockey

USA Field Hockey s Modifications to the 2017 FIH Rules of Hockey USA Field Hockey hs estlished tht the Interntionl Hockey Federtion (FIH) will e the ultimte uthority for rules governing the sport of hockey in the United Sttes. This rule ook is reprinted under the uthority

More information

OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP75H-10 HYDRAULIC WINCH.

OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP75H-10 HYDRAULIC WINCH. W. W. Patterson Company 3 Riversea Road Pittsburgh, PA 15233 Phone: 800-322-2018 FAX: 412-322-2785 OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP75H-10 HYDRAULIC WINCH. Please fill in the following blanks

More information

Chapter 4 Group of Volunteers

Chapter 4 Group of Volunteers CHAPTER 4 SAFETY CLEARANCE, FREEBOARD AND DRAUGHT MARKS 4-1 GENERAL 4-1.1 This chpter specifies the minimum freebord for inlnd wterwy vessels. It lso contins requirements concerning the indiction of the

More information

Rules of Hockey including explanations. Effective from 1 January 2017

Rules of Hockey including explanations. Effective from 1 January 2017 From 1 Jnury 2017 Rules of Hockey including explntions Effective from 1 Jnury 2017 Copyright FIH 2016 The Interntionl Hockey Federtion Rue du Vlentin 61 CH 1004 Lusnne Switzerlnd Tel. : + 41 21 641 0606

More information

OPERATION and MAINTENANCE Guide

OPERATION and MAINTENANCE Guide Catalog No. AIR1000 Winch and Hoist OPERATION and MAINTENANCE Guide Cat. No. AIR1000 1250 Lb. Single Line Pull READ THIS BEFORE OPERATING UNIT INSTALLATION: Mount on clean, flat surface. Use 1/2" mounting

More information

CYLINDERS HYDRAULIC HOIST CYLINDERS

CYLINDERS HYDRAULIC HOIST CYLINDERS CYLINDERS HYDRULIC HOIST CYLINDERS The combination of strict machining tolerances, solid stop contact faces, and larger overlap between the stages has resulted in one of the strongest and most stable cylinder

More information

VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns , , , , , )

VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns , , , , , ) VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns 3714022, 3714028, 3714034, 3714040, 3714043, 3714046) REIMANN & GEORGER CORPORATION MARINE PRODUCTS BUFFALO, NY P/N 6112103 04/09/18 1 SAFETY 1.1 INTRODUCTION

More information

United States Patent (19)

United States Patent (19) United Sttes Ptent (19) Mobley (11) 45) Ptent Number: Dte of Ptent: Nov. 19, 1991 (54) BICYCLE RACK FORMOUNTING ON A VAN 76 Inventor: Mrk H. Mobley, P.O. Box 636, Norris, Tenn. 37828 21 Appl. No.: 436,492

More information

APPNA SPRING MEETING CHICAGO, ILLINOIS RETAIL BAZAAR REGISTRATION MARRIOTT DOWNTOWN MAGNIFICENT MILE 540 NORTH MICHIGAN AVENUE

APPNA SPRING MEETING CHICAGO, ILLINOIS RETAIL BAZAAR REGISTRATION MARRIOTT DOWNTOWN MAGNIFICENT MILE 540 NORTH MICHIGAN AVENUE 1 PPN SPRING MEETING 2018 CHICGO, ILLINOIS PRIL 26 29, 2018 MRRIOTT DOWNTOWN MGNIFICENT MILE 540 NORTH MICHIGN VENUE RETIL ZR REGISTRTION 2 COMPNY NME CONTCT NME DDRESS RETIL ZR REGISTRTION PREFERRED PHONE

More information

SNOWDRIFTER G1 CONSTRUCTION MANUAL

SNOWDRIFTER G1 CONSTRUCTION MANUAL ch 7-14 SNOWDRIFTER G1 CONSTRUCTION MNUL YERS Length Max weight Time to build 98-125 cm / 39-49 inch 80kg / 176 lbs 2 hours WRNING - IMPORTNT NOTICE TO PRENTS efore you start constructing and use our product,

More information

2017 Mercury Marine. Xi3 Wireless Edition. Operation Maintenance Installation Warranty Manual

2017 Mercury Marine. Xi3 Wireless Edition. Operation Maintenance Installation Warranty Manual 2017 Mercury Mrine Xi3 Wireless Edition Opertion Mintennce Instlltion Wrrnty Mnul 8M0130831 1117 eng eng ORIGINAL LANGUAGE INSTRUCTIONS FCC nd IC Complince Sttement Xi SERIES WIRELESS FOOT PEDAL FCC ID

More information

Triple Tine Mechanical Grapple

Triple Tine Mechanical Grapple Attachment Solutions Triple Tine Mechanical Grapple Operators Manual KENCO Mechanical Grapple Operation Manual 1 TABLE OF CONTENTS 170 State Route 271 Section I. General Information.... 3 Section II. Safety...

More information

OPERATIONS and SAFETY MANUAL

OPERATIONS and SAFETY MANUAL OPERATIONS and SAFETY MANUAL LIFETIME WARRANTY SPECIAL SAFETY FEATURES: 1. Hook starts to open when device exceeds weight limit. 2. Latch Pops when weight is exceeded. At this point remove the load from

More information

OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M)

OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M) OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M) READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND SAFETY INFORMATION IN THIS MANUAL BEFORE OPERATING OR 04/17 (M6K-M) SERVICING THIS TOOL TABLE

More information

The Discussion of this exercise covers the following points: The open-loop Ziegler-Nichols method. The open-loop Ziegler-Nichols method

The Discussion of this exercise covers the following points: The open-loop Ziegler-Nichols method. The open-loop Ziegler-Nichols method Exercise 6-3 Level Process Control EXERCISE OBJECTIVE In this exercise, you will perform PID control of level process. You will use the open-loop step response method to tune the controller. DISCUSSION

More information

90-8M eng. Xi5 Wireless Edition Mercury Marine

90-8M eng. Xi5 Wireless Edition Mercury Marine 2014 Mercury Mrine Xi5 Wireless Edition eng 90-8M0097265 814 eng ORIGINAL LANGUAGE INSTRUCTIONS FCC nd IC Complince Sttement Xi5 WIRELESS FOOT PEDAL FCC ID MVU09291 Xi5 WIRELESS REMOTE FCC ID MVU09305

More information

2-4 YEARS RIDER CONSTRUCTION MANUAL cm 30 kg 90 min. Length Max weight Time to build

2-4 YEARS RIDER CONSTRUCTION MANUAL cm 30 kg 90 min. Length Max weight Time to build RIDER CONSTRUCTION MNUL 2-4 YERS Length Max weight Time to build 88-98 cm 30 kg 90 min WRNING - IMPORTNT NOTICE TO PRENTS efore you start constructing and use our product, please carefully read the following

More information

OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP50-H-14 HYDRAULIC WINCH.

OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP50-H-14 HYDRAULIC WINCH. W. W. Patterson Company 3 Riversea Road Pittsburgh, PA 15233 Phone: 800-322-2018 FAX: 412-322-2785 OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP50-H-14 HYDRAULIC WINCH. Please fill in the following blanks

More information

Operation Maintenance Installation Warranty Manual

Operation Maintenance Installation Warranty Manual 2017 Mercury Mrine Xi5 Wireless Edition Opertion Mintennce Instlltion Wrrnty Mnul 8M0124200 117 eng eng ORIGINAL LANGUAGE INSTRUCTIONS FCC nd IC Complince Sttement Xi5 WIRELESS FOOT PEDAL FCC ID MVU09291

More information

Instructions. Electronic Aquarium Water Change System. Replenishing Water. Extracting Water. Includes instructions for:

Instructions. Electronic Aquarium Water Change System. Replenishing Water. Extracting Water. Includes instructions for: Instructions Electronic Aqurium Wter Chnge System Includes instructions for: Replenishing Wter Extrcting Wter INTRODUCTION WHAT S INCLUDED The Aquplenish Wter Chnger conditions, monitors nd replenishes

More information

Bicycle wheel and swivel chair

Bicycle wheel and swivel chair Aim: To show conservtion of ngulr momentum. To clrify the vector chrcteristics of ngulr momentum. (In this demonstrtion especilly the direction of ngulr momentum is importnt.) Subjects: Digrm: 1Q40 (Conservtion

More information

OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 3K Puller (M3K-M)

OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 3K Puller (M3K-M) OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 3K Puller (M3K-M) 04/17 (M3K-M) READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND SAFETY INFORMATION IN THIS MANUAL BEFORE OPERATING OR SERVICING THIS TOOL TABLE

More information

OPERATIONS/PARTS MANUAL FOR PATTERSON'S HAND OPERATED WINCH

OPERATIONS/PARTS MANUAL FOR PATTERSON'S HAND OPERATED WINCH DOC # 5071-A W. W. Patterson Company 3 Riversea Road Pittsburgh, PA 15233 Phone: 800-322-2018 FAX: 412-322-2785 OPERATIONS/PARTS MANUAL FOR PATTERSON'S HAND OPERATED WINCH Please fill in the following

More information

REQUEST FOR COMMENTS

REQUEST FOR COMMENTS REQUEST FOR COMMENTS NEW UNIFORM STNDRD DRWING NUMER 217.S2, "RESIDENTIL CUR ND GUTTER R-TYPE"; MODIFICTIONS TO STNDRD DRWING NUMERS 223, 224, 226.S1, ND 227.S1 The Specifications Subcommittee of the Regional

More information

310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment

310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment OPERATOR S MANUAL FOR MORSE TILT-TO-LOAD DRUM ROTATOR SAFETY INFORMATION: While Morse Manufacturing Co. drum handling equipment is engineered for safety and efficiency, a high degree of responsibility

More information

Pool Ladder. Owner s Manual For: 48in (122 cm) model. For illustrative purposes only. Pool is not provided. IMPORTANT! DO NOT RETURN PRODUCT TO STORE

Pool Ladder. Owner s Manual For: 48in (122 cm) model. For illustrative purposes only. Pool is not provided. IMPORTANT! DO NOT RETURN PRODUCT TO STORE OWNER S MNUL Pool Ladder Owner s Manual For: 48in (122 cm) model For illustrative purposes only. Pool is not provided. IMPORTNT SFETY RULES Read, understand, and follow all instructions carefully before

More information

Valve Proving System for automatic Shutoff Valves

Valve Proving System for automatic Shutoff Valves LGY lve Proving System for utomtic Shutoff lves 11... The 11... vlve proving system is designed for use with shutoff vlves in connection with gs urners nd gs pplinces. n the event of indmissile lekge,

More information

IGF Research Project N Safer High Heels

IGF Research Project N Safer High Heels IGF Reserch Project 17868 N Sfer High Heels Survivl of compnies in the fshion nd sesonlly dependent sectors such s the footwer industry depends upon their ility to implement the ltest trends. Shoe ottoms

More information

600 / 600FC OWNER'S MANUAL

600 / 600FC OWNER'S MANUAL PROGRESSION 600 / 600FC OWNER'S MANUAL Issue 2 / Version E - Dec. 10, 1997 Copyright 1997 GAMMA Sports - All Rights Reserved PROGRESSION 600 / 600FC OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY

More information

T-016 ASSEMBLY MANUAL MODEL ROCK AND ROLL Main Street NE Minneapolis, MN

T-016 ASSEMBLY MANUAL MODEL ROCK AND ROLL Main Street NE Minneapolis, MN MODEL T-016 ASSEMBLY MANUAL ROCK AND ROLL 5280 Main Street NE Minneapolis, MN 55421 1.877.226.7824 www.kurtkinetic.com COMPONENTS Tools Required for Assembly: 17mm Wrench or Adjustable Wrench When unpacking,

More information

Dual Monitor Desk Mount

Dual Monitor Desk Mount Dul Mnitr Desk Munt Instructin Mnul SKU: STAND-V002 Scn the QR cde with yur mbile device r llw the link r helpul vides nd speciictins relted t this prduct. https://viv-us.cm/prducts/stnd-v002 help@viv-us.cm

More information

Winchline n a box WINCH LINE SELECTION GUIDE. Wire Rope Winchlines are superior to most other winchlines found in the market place due to the

Winchline n a box WINCH LINE SELECTION GUIDE. Wire Rope Winchlines are superior to most other winchlines found in the market place due to the Winchline n a box Wire Rope Winchlines are superior to most other winchlines found in the market place due to the eye) end terminations. Each eye is protected by a steel liner (thimble) to guard against

More information

OWNERS MANUAL. Model Shown with optional Primary Mooring Cleats. Portable Mooring System SAFETY OPERATION MAINTENANCE PARTS

OWNERS MANUAL. Model Shown with optional Primary Mooring Cleats. Portable Mooring System SAFETY OPERATION MAINTENANCE PARTS OWNERS MANUAL Model 2400 Shown with optional Primary Mooring Cleats. Portable Mooring System SAFETY OPERATION MAINTENANCE PARTS CAUTION: Before using your new Pier Tender, read rules for Safety, Operation,

More information

Chapter 2 Rigging. Cutting Wire Rope. Anchoring Wire Rope to Drum. Winding Wire Rope Onto Drum

Chapter 2 Rigging. Cutting Wire Rope. Anchoring Wire Rope to Drum. Winding Wire Rope Onto Drum Chapter 2 Rigging Cutting Wire Rope The wire rope must be tightly seized on both sides of the point where the wire rope will be cut, as shown in Figure 2-1. Seize the wire rope with either seizing wire

More information

453 Series Steam Heated Vaporizing Regulator

453 Series Steam Heated Vaporizing Regulator ADI 0453A Certified ISO 9001:2000 453 Series Steam Heated Vaporizing Regulator INSTALLATION AND OPERATION INSTRUCTIONS Before Installing or Operating, Read and Comply with These Instructions Controls Corporation

More information

2000 lb manual winch

2000 lb manual winch 2000 lb manual winch Model 41694 Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011

More information

OPERATIONS MANUAL IMPORTANT SAFETY INFORMATION

OPERATIONS MANUAL IMPORTANT SAFETY INFORMATION OPERATIONS MANUAL IMPORTANT SAFETY INFORMATION Please read, understand and follow all safety information contained in these instructions prior to the use of this tool. Retain these instructions for further

More information

Workrite Sierra HX & HXL Assembly Instructions for 3-leg Electric Workcenters

Workrite Sierra HX & HXL Assembly Instructions for 3-leg Electric Workcenters Workrite ierr HX & HXL Assemly Instrutions for 3-leg Eletri Workenters #1500216- Rev Workrite ierr HX & HXL Eletri Workenters - Assemly Instrutions for 3-leg les Rer Leg rket* Qty: 2 List of rts, grouped

More information

DIRECT DRIVE DIXIE DOUBLE SEAMER Model 25D

DIRECT DRIVE DIXIE DOUBLE SEAMER Model 25D OPERATOR'S MANUAL DIRECT DRIVE DIXIE DOUBLE SEAMER Model 25D LUBRICATE DAILY: A. Gears inside gear housing at chuck shaft (1) Oil B. Seam rolls and cam rolls (4) - Oil C. Seam roll levers through gear

More information

Warning CABLE REPLACEMENT INSTRUCTIONS. Questions? - Call Telpro Inc. Customer Service at or

Warning CABLE REPLACEMENT INSTRUCTIONS. Questions? - Call Telpro Inc. Customer Service at or CABLE REPLACEMENT INSTRUCTIONS Warning Read and follow these warnings and the instructions that follow. Failure to do so could result in serious property damage and/or serious bodily injury. BEFORE operating

More information

OPERATIONS/PARTS MANUAL FOR PATTERSON'S MODEL # WWP40M-LPS-6 LOW-PROFILE BARGE CONNECTOR WINCH

OPERATIONS/PARTS MANUAL FOR PATTERSON'S MODEL # WWP40M-LPS-6 LOW-PROFILE BARGE CONNECTOR WINCH W. W. Patterson Company 3 Riversea Road Pittsburgh, PA 15233 Phone: 800-322-2018 FAX: 412-322-2785 OPERATIONS/PARTS MANUAL FOR PATTERSON'S MODEL # WWP40M-LPS-6 LOW-PROFILE BARGE CONNECTOR WINCH Please

More information

SIGNATURE DEF REELS Models: Bare Reel Reel Reel Reel

SIGNATURE DEF REELS Models: Bare Reel Reel Reel Reel SERVICE BULLETIN SB2023 Rev C 7/11 SIGNATURE DEF REELS Models: 2400-006 Bare Reel 2400-007 16 Reel 2400-008 20 Reel 2400-009 30 Reel Thoroughly read and understand this manual before installing, operating

More information

Asbestos Management Program

Asbestos Management Program ( Asbestos Mngement Progrm < West Virgini University Morgntown, WV 26506 West Virgini University '(/' Asbestos Mngement Progrm Best Prctice Mnul 1 of 22 Tble Of Contents 1.0 INTRODUCTION 4 1.1 1.2 1.3

More information

Hand winch MANIBOX GR

Hand winch MANIBOX GR Hand spurgear winch Hand winch MANIBOX GR Instruction manual UK 34-331.09/9 PRODUCT DEVELOPED AND MANUFACTURED ACCORDING TO STANDARD NF EN 13157 In an endeavour to improve its products, HUCHEZ reserves

More information

ATD /8 x 50 Retractable Air Hose Reel Owner s Manual

ATD /8 x 50 Retractable Air Hose Reel Owner s Manual ATD-31166 3/8 x 50 Retractable Air Hose Reel Owner s Manual Features Heavy-gauge, all-steel reel assembly 8-position ratchet mechanism locks reel at desired hose length 5-position adjustable roller outlet

More information

GRENADES INTRODUCTION: EOD CONSIDERATIONS ANTI-ARMOR/HEAT: SAFETY: FRAGMENTATION: IMPACT FRAGMENTATION: FOR OFFICIAL USE ONLY FOR OFFICIAL USE ONLY

GRENADES INTRODUCTION: EOD CONSIDERATIONS ANTI-ARMOR/HEAT: SAFETY: FRAGMENTATION: IMPACT FRAGMENTATION: FOR OFFICIAL USE ONLY FOR OFFICIAL USE ONLY INTRODUCTION: Hnd or rifle projected. Min chrge includes HE, riot-control gents, smokes, nd incendiry nd pyrotechnic mterils. Fuzing is vried nd my be time-dely or impct fuzed. Are esily nd frequently

More information

bark bark bat bat Multiple Meaning Words: Kindergarten to Grade 2 More Teaching Tools at harsh sound made by a dog

bark bark bat bat Multiple Meaning Words: Kindergarten to Grade 2 More Teaching Tools at  harsh sound made by a dog the brk the brk bt bt hrsh sound mde by dog Mx, stop brking! outside cover of the trunks, brnches, nd roots of woody plnts The brk of this tree is very rough. club of wood or metl used to hit the bll in

More information

DISASSEMBLING & REASSEMBLING CARTRIDGE INSTALLING SEATPOST ON BIKE

DISASSEMBLING & REASSEMBLING CARTRIDGE INSTALLING SEATPOST ON BIKE INTRODUCTION BILL OF MATERIALS SPECIFICATIONS & TOOLS PROCEDURES DISASSEMBLING & REASSEMBLING CARTRIDGE INSTALLING SEATPOST ON BIKE OPERATION OF SEATPOST GIANT LIMITED WARRANTY 1 INTRODUCTION Congratulations

More information

44in Side Discharge Mower for Wheel Horse XL 440H Lawn Tractors Model No Serial No and Up

44in Side Discharge Mower for Wheel Horse XL 440H Lawn Tractors Model No Serial No and Up Form No. 5-8 in Side Discharge Mower for Wheel Horse XL 0H Lawn Tractors Model No. 790 Serial No. 5000000 and Up Operator s Manual Register your product at www.toro.com Original Instructions (EN) Contents

More information

30T A/Manual Hydraulic Shop Press

30T A/Manual Hydraulic Shop Press 30T A/Manual Hydraulic Shop Press Operation Manual 1 1. Important Information 1.1 Safety Information 1.1.1 Hazard Symbols Used in the Manuals This manual includes the hazard symbols defined below when

More information

Wildcat LB Winch Kit. Operator s Manual Installation Instructions Replacement Parts List. With Wireless Control System.

Wildcat LB Winch Kit. Operator s Manual Installation Instructions Replacement Parts List. With Wireless Control System. p/n 2259-560 Wildcat 4000 LB Winch Kit With Wireless Control System Operator s Manual Installation Instructions Replacement Parts List 2012 Arctic Cat Inc. Trademarks of Arctic Cat Inc. Thief River Falls,

More information

TOURNAMENT REGULATIONS OUTDOOR COMPETITIONS

TOURNAMENT REGULATIONS OUTDOOR COMPETITIONS TOURNAMENT REGULATIONS OUTDOOR COMPETITIONS Octoer 2012 INTERNATIONAL HOCKEY FEDERATION CONTENTS 1 Rules of competition 2 Tournment Officils 3 Tem entry 4 Pre-tournment riefing meetings 5 Composition of

More information

2,500/4,000 LB Easy Riser Vertical Cable Feighner Lift

2,500/4,000 LB Easy Riser Vertical Cable Feighner Lift 2,500/4,000 LB Easy Riser Vertical Cable Feighner Lift CAUTION - PUT SAFETY FIRST 1. Before attempting to install or operate this lift, study and fully understand the proper operating procedures and safety

More information