MODEL TRIPEX PULLEY SYSTEM
|
|
- Gary Anthony
- 5 years ago
- Views:
Transcription
1 MODEL TRIPEX PULLEY SYSTEM 1
2 PARTS LIST FOR TRIPEX PULLEY SYSTEM Note: Check with your architect or a professional contractor for hardware required to attach the unit to the wall and floor in your facility. Before setting up, check to make sure that you have received the following: 1 FLOORBOARD W/PULLEYS 8 5 /8 W x 30 L x 1 H 1 MIDDLE WALLBOARD W/PULLEYS 5 5 /8 W x 24 L x ¾ H 1 TOP WALLBOARD W/PULLEYS 5 5 /8 W x 24 L x ¾ H 1 CEILING BOARD W/PULLEYS 5 5 /8 W x 24 L x 1 H ROD GUIDES 2 - WEIGHT SLIDES 2 - TRIPLEX SLIDES 10 - WEIGHTS (EACH 2 1 /2 lbs) 6 - NYLON STOPPERS HANDLES 6 -ROPE CLIPS 4-2 PHILLIPS HEAD BOLTS 1 - WEIGHT HOLDER 6 - SWIVEL HOOKS + 2
3 INSTALLATION INSTRUCTIONS (See Illustration Installation Drawing) Overall dimension for installation is 30 inches wide by 9 inches deep by 10 feet tall area. The ceiling must be 10 feet high to install the pulley system. If it s less than 10 feet, one set of guide rods will have to be cut to length to install system. (See picture below) FOR MODEL , TRIPLEX PULLEY If ceiling is 10, 11 or 12, use 56 rods. If ceiling is 9, use 44 rods top level and 56 rods for the lower level. 9 FT CEILING 7 10 FT CEILING 11 FT CEILING FT CEILING 31 CUT TO 44 LT Make sure that you have the appropriate pieces of hardware and tools to install the pulley system. You will need the following to assemble/ install the pulley system. Hardware for attaching the pulley boards to the wall, floor and ceiling is not supplied as hardware required will vary according to the structure of your facility. Recommendation use lag bolts for wood for wood stud walls. Level Pliers Hex head 3/8 socket and ratchet Allen hex head set keys Tape measure Hacksaw (if any height modification is necessary) Lag screws for wall, ceiling and floor Remove from parts kit (4) Phillips Head threaded bolts, fasten into flatboard as shown on following page. 3
4 INSTALLATION INSTRUCTIONS Before beginning to install the pulley system, ensure that the location selected to set up the pulley system has appropriate structural stability. The pulley boards will need to be secured to a structurally sound member in the wall and ceiling. Standard wall studs are acceptable and do not require any extra reinforcement. The floorboard, wallboard, and ceiling board have been pre-drilled for two lag bolts. Remove from parts kit: four Phillips Head Bolts, and fasten into floorboard as shown here. LT. FRONT 1B RT. FRONT Make sure you have the appropriate pieces of hardware and tools to install the pulley system. You will need the following to assemble/install the pulley system. Hardware for attaching the pulley boards to the wall and floor (not supplied, as hardware required will vary according to the structure of your facility). Level Drill with appropriate bits for lead holes Pliers Hex head socket set Tape measure Hacksaw (if any height modification is necessary) 1A 1A 1. From the bottom of floorboard, screw in four Phillips Head Bolts at Position 1A. 2. Place the floorboard on the floor flush against the wall. Position floorboard so pulley is opposite wall. Rotate pulley as needed so it is perpendicular to wall and metal guide tab on pulley holder is away from wall (see Figure 1 on page 4). 3. Locate the weight holder and thread it into the baseboard at Position 1B. 4. Place the weight plates on the weight holder. 5. Place four guide rods onto the inserted Phillips Head Bolts in the floorboard. 6. Slip the weight slide over and down the guide rods so that the weight slide rests against the floorboard. Be sure metal guide tab on pulley holder is facing away from the wall (see Figure 1 on page 4). 12. Tighten both set screws on the collar. 13. Repeat steps for the second side. 14. Place upper wallboard with pulleys over top four guide rods. 15. Make sure upper wallboard is level and lock into place by tightening both set screws in each collar. 16. Using hardware appropriate for your installation, secure upper wallboard to a stud in wall using holes in top and bottom of wallboard. 17. Line up ceiling board in front of the upper wallboard and parallel to the wall. Distance from wall should not exceed 18 inches. 18. Using hardware appropriate for your installation, secure ceiling board to ceiling joist using holes in top and bottom of ceiling board. 7. Place the lower wallboard with pulleys over the four guide rods. 8. Make sure wallboard is level and lock in place by tightening both set screws in each collar. 9. Using hardware appropriate for your installation, secure lower wallboard to stud in wall using holes in top and bottom of wallboard. 10. Slide one of the remaining weight slides over two of the remaining guide rods. 11. Place the weight slide and rods on the lower wallboard. Be sure metal guide tab on pulley holder is facing away from the wall. 19. Using hardware appropriate for your installation, secure floorboard using holes in each side of floorboard. 20. Rotate the top pulleys of the lower wallboard and ceiling board as needed so they are perpendicular to wall and the metal guide tabs are facing away from the wall (see Figure 1 on page 4). 21. Rotate pulleys directly below top pulleys on the lower wallboard as needed so they are positioned at a 45º angle with the metal guide tab on the pulley holder facing towards the weight holder. 22. Rotate top pulleys on upper wallboard as needed so they are perpendicular to the wall and the metal guide tab is facing towards the wall. 4
5 INSTALLATION INSTRUCTIONS Figure
6 THREADING THE ROPE Figure 2 A C END HERE THREAD ROPE THROUGH FLAT BAR IN TRIPLEX SLIDE AND SECURE (C) START HERE THREAD ROPE THRU PULLEYS 1. Remove three weights from the storage holder and slip onto the weight slide to keep slide in place. This will provide resistance to movement while threading rope through pulleys. 2. Thread the rope through the pulleys starting with pulley (A) - up, over and down to pulley - (B), down and under and up to flat bar in Triplex Slide (C). Tie a knot in the rope to secure it to the flat bar (C). B 6
7 ATTACHING THE MIDDLE HANDLE Figure 3 Follow the illustration to attach the pulley handle. a) b) c) d) e) Parts a) Pulley Handle b) Swivel Hook c) Clip d) Nylon Stopper e) Rope From end of rope, slide nylon stopper on rope until it rests against pulley on wallboard. 2. Pull rope until taught, tie knot on the top of the nylon stopper so rope threaded through pulleys remains taught. 3. Thread the clip on the rope. 4. Slip the rope through hook of the swivel. 5. Slip the rope through the second hole of the clip. 6. Tie a knot at the end of the rope. 7
8 THREADING THE TOP HANDLE Figure 4 Follow the illustration to thread top handle to rope, then follow directions to thread the rope. a) b) c) d) e) Parts a) Pulley Handle b) Swivel Hook c) Clip d) Nylon Stopper e) Rope From end of rope, slide the nylon stopper up rope 24 inches and tie a knot behind the stopper. 2. Thread clip on the rope. 3. Slip the rope through the hook of the swivel. 4. Thread the rope through the second hole of the clip. 5. Tie a knot in the end of the rope after the clip. 6. At this point the handle is complete. Use other end of the rope to thread through the pulleys (see figure 5 on page 9). Once the rope has been threaded, attach the 2nd handle (see figure 6 on page 10). 8
9 THREADING THE ROPE Figure 5 A START HERE THREAD ROPE THRU PULLEYS B D 1. Remove three weights from the storage holder and slip onto the weight slide to keep slide in place. This will provide resistance to movement while threading rope through pulleys. C 2. Thread the rope through the pulleys starting with pulley (A) up, over and down to pulley (B), through the top of pulley (B) frame, out the bottom of pulley (B) frame and down to pulley (C). Down and under (C), up and over pulley (D), down and under pulley (E). The handle with clip and nylon stopper should remain at top pulley. 3. When the rope is threaded through pulley (E), see Figure 6 (next page) to attach 2nd handle. END HERE E 9
10 ATTACHING THE BOTTOM HANDLE Figure 6 Follow the illustration to attach bottom pulley. a) b) c) d) e) Parts a) Pulley Handle b) Swivel Hook c) Clip d) Nylon Stopper e) Rope From end of rope, slide nylon stopper on rope until it rests against pulley on floorboard. 2. Pull rope until taught, tie knot on the top of the nylon stopper so rope threaded through pulleys remains taught. 3. Thread the clip on the rope. 4. Slip the rope through hook of the swivel. 5. Slip the rope through the second hole of the clip. 6. Tie a knot at the end of the rope. NOTE: To prevent excessive wear on rope(s), ensure user is positioned directly in front of top or bottom pulley. 10
11 WARRANTY Sammons Preston Tripex Pulley System is guaranteed to be free from defects in material and/or workmanship under normal use and service for a period of one year from date of purchase. The above guarantee is null and void if unauthorized repair and/or modification is performed on the unit. 11
MODEL CHEST PULLEY SYSTEM
MODEL 9180 CHEST PULLEY SYSTEM 1 PARTS LIST FOR CHEST PULLEY Note: Check with your architect or a professional contractor for hardware required to attach the unit to the wall and floor in your facility.
More informationMODEL / SINGLE and DUPLEX PULLEY SYSTEMS
MODEL 922181/922182 SINGLE and DUPLEX PULLEY SYSTEMS MODEL 922181 SINGLE PULLEY SYSTEM MODEL 922182 DUPLEX PULLEY SYSTEM 1 PARTS LIST FOR SINGLE/DUPLEX COLUMN PULLEYS Note: Check with your architect or
More informationFNFB-30 (30 FT FIELDPRO FOOTBALL BACKSTOP SYSTEM) Installation Instructions
FNFB-30 (30 FT FIELDPRO FOOTBALL BACKSTOP SYSTEM) Installation Instructions Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.com Rev: - Page
More informationSASK-A-POLE OWNERS AND USERS MANUAL
SASK-A-POLE OWNERS AND USERS MANUAL GENERAL INFORMATION The Saskatchewan Abilities Council s Sask-a-Pole accessibility and transfer aid is designed to help provide safe and easy access to chairs, beds,
More informationBALL STOP INSTALLTION GUIDE
BALL STOP INSTALLTION GUIDE GROUND SLEEVE INSTALLATION: 1. Locate the exact location of the ground sleeve. NOTE: Maximum recommended pole spacing is 20 feet on center. 2. Excavate the pole footing; refer
More informationATD /8 x 50 Retractable Air Hose Reel Owner s Manual
ATD-31166 3/8 x 50 Retractable Air Hose Reel Owner s Manual Features Heavy-gauge, all-steel reel assembly 8-position ratchet mechanism locks reel at desired hose length 5-position adjustable roller outlet
More informationLSA-BAWMBL. Wall-Mounted Boom Arm INSTRUCTIONS
LSA-BAWMBL Wall-Mounted Boom Arm INSTRUCTIONS 1 Precautions Do not exceed the maximum load capacity. Always engage safety locks and devices where applicable. Product should be used between -22 F and 140
More informationSAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER OCEAN BLUE ABOVE GROUND POOL LADDERS
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER OCEAN BLUE ABOVE GROUND POOL LADDERS ASSEMBLY AND INSTALLATION MANUAL FOR A-FRAME AND INPOOL LADDERS A-FRAME Part No. 400100 PROUDLY MADE IN
More informationTHOR 10 HAMMER CAGE INSTRUCTIONS
75 " 7m 78 4" m 6" 8.8m 45 ".70m 4.9deg 6 4" 6m 44 4".67m 75 " 7m 9 4" 0m 44".m 497 4".64m The 70, Thor Hammer Cage, consists of four heavy duty aluminum net poles. The unique pole structure reduces the
More informationImportant Note: Tighten lock nuts so the support tubes still swing freely see figure 2. There must be 1 2 threads of bolt past end of lock nuts.
Kit Contents: DESCRIPTION QTY. DESCRIPTION QTY. 2 Shank Assembly 1 Support Tube Assembly 1 Side Tube - Short 2 1-1/4 Shank 1 Center Tube - Long 1 3/8-16 x 2.0 Carriage Bolt 2 5/16-18 x 2.25 Carriage Bolt
More informationRehabPro Speed Pulley (M100S & M100FS) User Manual
RehabPro Speed Pulley (M100S & M100FS) User Manual 1. Inspection of Delivery Before unpacking the Pulley please inspect the packaging for shipping damage. Observable damage should be noted prior to signing
More informationAssembly Instructions. -Cantilever Boat Lifts
Assembly Instructions -Cantilever Boat Lifts Winch Instruction Page Safety Information 1. The winch is built for the multipurpose of hauling and lifting operations. It is not to be used as a hoist for
More informationInstallation Instructions MODEL VSTI-A020 Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Versa Steel Inc. Guide Cables No
Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Guide Cables No Guide Cables 1 August 4, 2011 Assembly Instructions: (Shown with a 2 board, 12 ft kit) ITEM NO. PART NUMBER DESCRIPTION
More informationOnly. Gives You the TechLock. System Advantage ASSEMBLY, DISASSEMBLY AND TROUBLESHOOTING INSTRUCTIONS FOR 3000 SERIES FONTAINE
April 00 Only Gives You the TechLock System Advantage ASSEMBLY, DISASSEMBLY AND TROUBLESHOOTING INSTRUCTIONS FOR 000 SERIES FONTAINE C o n n e c t y o u r b u s i n e s s w i t h F O N T A I N E April
More informationCHAPTER 5 REWIND STARTERS
GENERAL INFORMATION CHAPTER 5 REWIND S Rewind starters used on vertical shaft Tecumseh engines are top mount horizontal pull style or side mount vertical pull style. Horizontal shaft engines use side mounted
More informationUniversal Elevator Mount Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI U.S.A.
REQUIRED TOOLS AND MATERIALS: 2 Capable Adults Carpenter s Level 15 Tape Measure Pencil Universal Elevator Mount Owners Manual Customer Service Center N53 W2400 South Corporate Circle Sussex, WI 530 U.S.A.
More informationRBI Solar One-Piece Ground Mount Solution GM-GS
Solar Mounting System Installation Guide RBI Solar One-Piece Ground Mount Solution GM-GS Ballasted Ground Mount System RBI Solar 1292 Logan Circle NW Atlanta, GA 30318 513-618-7240 info@rbisolar.com OVERVIEW
More informationOWNER'S MANUAL. Copyright 2003 GAMMA - All Rights Reserved
OWNER'S MANUAL AL Issue 1 - December 2003 Copyright 2003 GAMMA - All Rights Reserved OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... ASSEMBLY INSTRUCTIONS PAGE 4... MOUNTING THE RACQUET PAGE
More informationCO V E R S TA R AU TO MAT I C S A F E T Y CO V E R INSTALLATION GUIDE
CO V E R S TA R AU TO MAT I C S A F E T Y CO V E R DECKMOUNT SYSTEM INSTALLATION GUIDE SECTIONS System Parts Reference...3 Standard Top Track...4-6 Mechanism... 7-10 Cover Fabric...11-16 Home Owner & Builder
More informationOWNER'S MANUAL. Copyright 1999 ATS - All Rights Reserved
OWNER'S MANUAL AL Issue 2 - August 19, 1999 Copyright 1999 ATS - All Rights Reserved OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... ASSEMBLY INSTRUCTIONS PAGE 4... MOUNTING THE RACQUET PAGE
More information8MAY15 US RACK, Inc Falcon Drive, Madera, CA
8MAY15 US RACK, Inc. - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTRUCTIONS for Bedrail-mounted MOTORCYCLE RACK, Model 2001-4TRA WARNING: Do NOT attempt to install or use this rack without following
More informationUniversal Anchoring Adapter For Mercedes
Universal Anchoring Adapter For Mercedes Anchoring Pin & Tube Set (For Most Mercedes Models) Users Manual 006 Chief Automotive Technologies, Inc. Chief s Limited One-Year Warranty & Liability CHIEF'S
More informationInstallation Instructions
116-3027, 116-3017 X-Pando Adjustable Steel Protector Installation Instructions 1404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 NB 6/28/10 607-0112 Step 1. Mounting
More informationX-6 STRINGING MACHINE OWNER'S MANUAL. Issue 1 - May Copyright 2004 GAMMA Sports - All Rights Reserved
X-6 STRINGING MACHINE OWNER'S MANUAL Issue 1 - May 2004 Copyright 2004 GAMMA Sports - All Rights Reserved OWNER'S MANUAL GAMMA X-6 TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3...ASSEMBLY
More informationPRISMA. Installation, Operation, & Maintenance Manual. Climbing Panel + FREEMount System. NOTE TO INSTALLERS Always Read Instructions Before Use
PRISMA Climbing Panel + FREEMount System Installation, Operation, & Maintenance Manual NOTE TO INSTALLERS Always Read Instructions Before Use This Manual contains information on the proper installation
More informationReach poles & cables system. product guide
Reach poles & cables system product guide Phantom Indoor Batting Cage reach poles & cables system This reach poles & cables system is engineered to maximize your interior space. This guide will walk you
More informationRehabPro Standard Pulley (M30, M50, M70, M30F, M50F, M70F)
RehabPro Standard Pulley (M30, M50, M70, M30F, M50F, M70F) User Manual RehabPro, Inc. 28215 North 25th Dale Phoenix, AZ 85085 602-317-7207 (phone) E-mail: sales@rehabpropulleys.com E-mail: kris@rehabpropulleys.com
More informationHP10168 & HP10169 KITS HP10152 / HP10154 / HP10156
HP10168/&HP10154 HP10169/KITS HP10152 HP10156 HP10152: 2" AMP Air Suspension Spacer Kit Ford F-450 Pickup 2WD & 4WD HP10154: 4" AMP Air Suspension Spacer Kit Ford F-450 Pickup 2WD & 4WD HP10156: 6" AMP
More informationMarine 6-Boat Free-Standing Racks SKU: Updated November 2011
Marine 6-Boat Free-Standing Racks SKU: 30-061 Updated November 011 Contains: Marine -Boat Free-Standing Racks (SKU 1-003) Marine 3 rd Boat Expansion Racks (SKU 1-0303) Marine Back Legs (SKU -001) 3 Sets
More informationCABLES-ONLY SYSTEM PRODUCT GUIDE
CABLES-ONLY SYSTEM PRODUCT GUIDE Phantom Indoor Batting Cage CABLES-ONLY SYSTEM This cables-only system is engineered to maximize your interior space. This guide will walk you through setting up your wall
More informationOPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M)
OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M) READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND SAFETY INFORMATION IN THIS MANUAL BEFORE OPERATING OR 04/17 (M6K-M) SERVICING THIS TOOL TABLE
More informationStand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS
1 Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new Stand-N-Fish Kayak Fishing System. Once installed on your kayak the Stand-N-Fish will take your kayak fishing
More informationA-FRAME RESIN IN & OUT FLIP UP LADDER
A-FRAME RESIN IN & OUT FLIP UP LADDER NE1222 NOTE FOR SAFETY PURPOSES ALL LADDERS SHOULD BE SECURED BY ATTACHING THEM TO THE TOP LEDGE OF THE POOL. (See step 13 for details) In order for the ladder to
More informationMODEL #7100X A-FRAME LADDER
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #7100X A-FRAME LADDER LADDER MUST BE ATTACHED TO POOL FRAME... DO NOT USE WITH INFLATABLE POOLS ASSEMBLY AND INSTALLATION MANUAL The Anti-Entrapment
More informationFIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions
FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions WARNING! WARNING! WARNING! THIS BASKETBALL SYSTEM IS SPRING LOADED AND SHIPPED UNDER TENSION. ATTEMPTING TO ASSEMBLE OR DISASSEMBLE ANY
More informationHoldUp Plus2. Safety Kit included: See additional instructions for installation. REAR WHEEL TRAY. BASE (1x) lock WASHER (1x) KEY (2x) SAFETY CLIP (1x)
HoldUp Plus2 InsTAll This product on 2" hitch version of the HoldUp Front WHEEL TRAY assembly (1x) REAR WHEEL TRAY assembly (1x) wrench (1x) BASE (1x) bolt (8X) Lock WASHER (8X) Washer (8x) KEY (2x) SAFETY
More informationGRAVITY BIKE RACK ASSEMBLY & OPERATING INSTRUCTIONS
GRAVITY BIKE RACK 94479 ASSEMBLY & OPERATING INSTRUCTIONS Due to continuing improvement, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011
More informationSTAND AID 1600/ ECONOSTAND
MAKERS OF STAND AID, POWER TOILET AID AND FREEDOM CHAIR STAND AID 600/ ECONOSTAND INSTRUCTIONS AND WARRANTY FOR STAND AID 600 STAND AID SERIAL # PO BOX 386 Sheldon, IA 50 (800) 83-8580 (7) 34-53 Fax: (7)
More informationDO NOT use any Alien Flier Zip Line Products or Accessories until you read and understand these SAFETY WARNINGS!
! WARNING DO NOT use any Alien Flier Zip Line Products or Accessories until you read and understand these SAFETY WARNINGS! A zip line can be very dangerous. Do not use this kit if you do not understand
More informationConfer Plastics Inc. - Installation Manuals CONFER PLASTICS, INC. CONFER PLASTICS, INC. POOL ENTRY SYSTEM FOR ABOVE-GROUND POOLS
Page 1 of 6 Other Installation Manuals CONFER PLASTICS, INC. CONFER PLASTICS, INC. POOL ENTRY SYSTEM FOR ABOVE-GROUND POOLS Adjusts to fit most above-ground pools with flat or slightly dished bottoms PARTS
More informationRef Part Part # Qty Letter A Rudder Catcher B X 1/2 PH Bolts C Rudder Bracket
Ref Part Part # Qty A Rudder Catcher 07.2694.0000 1 J B Q A B 10-32 X 1/2 PH Bolts 07.2136.0000 10 C Rudder Bracket 07.2689.0000 1 D Kayak Pad Eye 01.1315.0430 2 E Cherry Rivets 01.1315.0459 4 H T N P
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Models No. TD0101, TD0101F Description Impact Driver L PRODUCT P 1/ 14 CONCEPT AND MAIN APPLICATIONS Models TD0101 and TD0101F are cost-competitive 100N.m-class impact driver developed
More informationVL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns , , , , , )
VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns 3714022, 3714028, 3714034, 3714040, 3714043, 3714046) REIMANN & GEORGER CORPORATION MARINE PRODUCTS BUFFALO, NY P/N 6112103 04/09/18 1 SAFETY 1.1 INTRODUCTION
More information602 STRINGING MACHINE OWNER'S MANUAL
PROGRESSION 602 STRINGING MACHINE OWNER'S MANUAL AL Issue 1- April 2000 Copyright 2000 GAMMA Sports - All Rights Reserved PROGRESSION 602 STRINGING MACHINE TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2...
More informationFirst Team Sports, Inc. Stellar Recreational Volleyball System
First Team Sports, Inc. Stellar Recreational Volleyball System BILL OF MATERIALS A 2 Volleyball Vertical Post K 1 ½ Centerlock Nut B 2 Height Labels L 2 Carabiner Clip C 3 Net Clamp M 1 ½ x 2 Hex Bolt
More informationUSER MANUAL. DM65 Manual Flush/Tilt Combo Mount
USER MANUAL DM65 Manual Flush/Tilt Combo Mount 1 D1_1.11.11.indd 1 ! CAUTION When using this mounting system, basic precautions should be followed, including: Follow the entire installation/user s manual
More informationSide-of-Pole Mount for 1 Module (SPM1) For Module Types A & B
Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 080311-2 SP3363-1 Side-of-Pole Mount for 1 Module (SPM1)
More informationFirst Team Sports, Inc. Blast Recreational Volleyball System
First Team Sports, Inc. Blast Recreational Volleyball System BILL OF MATERIALS A 2 Volleyball Vertical Post K 1 ½ Centerlock Nut B 3 Net Clamp L 2 Carabiner Clip C 1 Pulley Clamp M 1 ½ x 2 Hex Bolt D 4
More informationMALONER. Installation & Loading Instructions - Please Read Before Beginning. Step 1: Installing Carriers to Cross Bars
SeaWing V-STYLE KAYAK CARRIER 60mm 50mm Rubber Plugs SeaWing Kayak Carriers 12 Load Straps Jawz Universal Adapters Mounting Bolts T-Knobs 12 Safety Lines MD Series Only Installation & Loading Instructions
More informationORNAMENTAL CANTILEVER GATE INSTRUCTIONS
U.S.A. Patent Number 5,36,83 ORNAMENTAL CANTILEVER GATE INSTRUCTIONS *NOTICE: Ornamental Cantilever Gates are supplied with rolls of 2 mesh safety screening in sufficient quantities to cover the entire
More informationInstallation Instructions - Steel 4 Spring Arm Kits , , , ,
Installation Instructions - Steel Spring Arm Kits 50-0709, 50-079, 50-0750, 50-075, 50-078 GR 8// 07-00 0 N. Marshall Ave. El Cajon CA. 900 For technical support call us at (800) 8-075 Step. Determining
More informationSTERN MOTOR FOOT CONTROL KIT For use with the Torqeedo 403 Ultralight
STERN MOTOR FOOT CONTROL KIT For use with the Torqeedo 403 Ultralight The Wilderness Systems Foot Control Kit is designed to connect directly to a Torqeedo 403 Ultralight motor mounted on the stern of
More informationBackboard and Rim Owners Manual
REQUIRED TOOLS AND MATERIALS: Two (2) Capable Adults Tape Measure Backboard and Rim Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. Step Ladder - 8ft. (2.4
More informationSteel Spring Driven Reel Instruction Manual
Steel Spring Driven Reel Instruction Manual WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in
More informationNICROS-GRANITPANELS INSTALLATION MANUAL
NICROS-GRANITPANELS INSTALLATION MANUAL NICROS, INC. 845 PHALEN BLVD. ST. PAUL, MN 55106 PHONE: 651.778.1975 FAX: 651.778.8080 THANK YOU FOR YOUR PURCHASE OF THIS NICROS PRODUCT Nicros-GranitPanels are
More informationSPINNER RIDE GETTING STARTED GUIDE. Welcome to a personalized fitness experience for your members
This addendum accompanies your equipment documentation and is additional information concerning the heart rate features for your equipment and console. Important The heart rate feature is intended for
More information310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment
OPERATOR S MANUAL FOR MORSE TILT-TO-LOAD DRUM ROTATOR SAFETY INFORMATION: While Morse Manufacturing Co. drum handling equipment is engineered for safety and efficiency, a high degree of responsibility
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Weight Distributing Hitch Ball Mount Class IV See dealer application charts 999T7 WQ820 TOOLS REQUIRED: 14 mm Wrench or Ratchet
More informationImport Bike Rack OEM INSTALLATION MANUAL
Import ike Rack OEM INSTLLTION MNUL TLE OF ONTENTS System Information 2 Safety Information 2 Resources Required 3 Preparation 3 Under umper ttachment 3 Over umper ttachment 3 Installation 3 Under umper
More informationPage 1. Single Scull Car Rack Assembly and User s Manual " "
Page 1 Single Scull Car Rack Assembly and User s Manual Page 2 Items in the box: (2) V cradles (2) 4 rails (1) 1 3/4 X 18 rail coupler (4) 1/4-20 X 4 1/2 bolts (2) 1/4-20 X 2 1/2 bolts (12) 1/4 flat washers
More informationOPERATING and MAINTENANCE INSTRUCTIONS MAXIS 3K Puller (M3K-M)
OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 3K Puller (M3K-M) 04/17 (M3K-M) READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND SAFETY INFORMATION IN THIS MANUAL BEFORE OPERATING OR SERVICING THIS TOOL TABLE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08L07-E09-100 Application 2013 ODYSSEY Publications No. AII 13265 Issue Date AUG 2012 Put this information in the glove box with the vehicle owner s manual. PARTS
More informationV-PLOW. ACCUFLO Conveyor Belt Cleaning System MAX SYSTEMS GUIDE. Engineering. LIB-CP-SYS-01-E Rev.9. Page 1
ACCUFLO Conveyor Belt Cleaning System Page 1 Conveyor Belt Cleaning System - System Nomenclature CATGORY MAINFRAM INFORMATION BLAD INFORMATION CP=CONVYOR PRODUCTS CP - PA - 36 M - G 83 SYSTM TYP BLT WIDTH
More informationTOURNAMENT ICE. 8Ft-Gold Standard Manual Score Home Air Hockey Game Assembly Instructions / Manual
TOURNAMENT ICE 8Ft-Gold Standard Manual Score Home Air Hockey Game Assembly Instructions / Manual Thank you for purchasing a Gold Standard Games product. All of us at Gold Standard Games want you to be
More informationCover EX Installation Instructions
Cover EX Installation Instructions 1. Lay out all the parts and verify that they are all present according to the Cover EX Parts and Hardware List. See Fig 1. Call 800-730-7727 for all replacement and
More informationBig Ride ASSEMBLY AND INSTALLATION INSTRUCTIONS * * C A U T I O N * *
Big Ride ASSEMBLY AND INSTALLATION INSTRUCTIONS * * C A U T I O N * * S.R. SMITH BIG RIDE SLIDES ARE MANUFACTURED FOR INSTALLATION AND USE ON INGROUND SWIMMING POOLS ONLY. THE BIG RIDE IS NEVER TO BE INSTALLED
More information600 / 600FC OWNER'S MANUAL
PROGRESSION 600 / 600FC OWNER'S MANUAL Issue 2 / Version E - Dec. 10, 1997 Copyright 1997 GAMMA Sports - All Rights Reserved PROGRESSION 600 / 600FC OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY
More informationF-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN F-1281-R LOWER RIGHT SKIN F-1208-R FUSELAGE FRAME
F-1282-R BOTTOM RIGHT SKIN F-1283C J-STIFFENER F-1278 TOP SKIN F-00009-L ADAHRS BRACKET F-00009-R ADAHRS BRACKET F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN SECTION 10: TAILCONE F-1279-L UPPER LEFT
More informationInstructions. Follow All Instructions Before Assembling Or Using This Product
Instructions Follow All Instructions Before Assembling Or Using This Product IMPORTANT DO NOT RETURN THIS PRODUCT TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE: (800) 492-9334 WARNING: Improper use
More informationLock-N-Load. Bullet Feeder
Lock-N-Load Bullet Feeder table of contents steps Overview... 2 List of required hand tools... 2 1: Mounting the Bullet Feeder to the Bench... 3 2: Mounting the Bullet Feed Hopper... 4 3: Bullet Feed Hopper
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More informationE. Test, and if needed, adjust tips of antenna. 1. Mark will test antennas with meter at ground end of feedline bundle. Will take 10 minutes.
Project Steps Overview: A. Prepare: B. Raise up small antenna. C. Raise up large antenna. D. Connect to new bundle of 4-feedlines pulled up from ground. E. Test, and if needed, adjust tips of large antenna.
More informationSPOOLER INSTRUCTIONS. STEP 12 If you are going to paint your posts, that should be done at this time.
STEP 4 Starting where you marked the end post location, move down your fence line 6 feet and make another mark. This mark is where your second upright post will be installed. Continuing down the fence
More informationCENTER-STRUT HEIGHT ADJUSTMENT UNITS MANUAL OPERATION
ASSEMBLY, INSTALLATION &MAINTENANCE INSTRUCTIONS CENTER-STRUT HEIGHT ADJUSTMENT UNITS MANUAL OPERATION No. 00900-211 and 00900-506 Nylon spacer (2) located between fan backboard support and backboard FAN
More informationSAVE THESE INSTRUCTIONS
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #8100X OUTSIDE SAFETY LADDER 48" TO 54" FOR USE WITH CONFER PLASTICS IN POOL STEPS LADDER MUST BE ATTACHED TO POOL FRAME... DO NOT USE
More informationInstructions. Follow All Instructions Before Assembling Or Using This Product
Instructions Follow All Instructions Before Assembling Or Using This Product IMPORTANT DO NOT RETURN THIS PRODUCT TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE: (800) 492-9334 WARNING: Improper use
More informationMUELLER. Mega-Lite Drilling Machine. Reliable Connections. table of contents PAGE. Equipment 2. Operating Instructions 3-4. Parts Information 5
operating Instructions manual MUELLER Mega-Lite Drilling Machine table of contents PAGE Equipment 2 Operating Instructions 3-4 Parts Information 5 Travel Charts 6-11! WARNING: 1. Read and follow instructions
More informationTroyer s Gourd Rack 8 unit F R H O P
B E A D I M-N L Vertical Parts F R H O P Horizontal Parts C G J Updated 11/16 Parts List A: Top of Pole B: Bottom of Pole C: 48 Ground Stake D: Top Perch rods 48 long E: Hub F: Rope Winder w/ attached
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO AND TANDEM KAYAKS IMPORTANT: For Tandem kayaks, the Supplemental Kit will be needed in addition to this kit and can be purchased through a registered dealer. The addition of a rudder to
More informationTripod Setup Guide (M-TPx)
Items needed: 1/2 inch wrench, mast level (M-MLA), medium size wire cutters, crescent wrench, all-purpose grease, tape measure, tie wraps, redi-mix cement (optional), shovel (optional), sledge hammer (for
More informationDetroit Speed, Inc. A-body Rear Coilover Conversion Kit A-body (Moser Rear Axle) P/N: , , , , ,
Detroit Speed, Inc. A-body Rear Coilover Conversion Kit 1964-1972 A-body (Moser Rear Axle) P/N: 042411, 042412, 042413, 042417, 042418, 042419 The Detroit Speed, Inc. A-body Rear Coilover Conversion Kit
More informationSide-of-Pole Mount for 1 Module (SPM1) For Module Type C
Module Type Width Length C 22-27 56-63 Side-of-Pole Mount for 1 Module (SPM1) For Module Type C ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 022212-1 Side-of-Pole Mount
More informationHMO500. Headrest Hardware. Stealth s Multi-Axis Headrest Hardware. Installation Manual INSTALLATION INSTRUCTIONS FOR. Stealth Products HMO500 Hardware
Headrest Hardware Installation Manual HMO500 Stealth s Multi-Axis Headrest Hardware INSTALLATION INSTRUCTIONS FOR Stealth Products HMO500 Hardware Compatible with: All Stealth Products Headrests Customer
More informationSCOUT DECK ANCHOR 3 1/4" BONDING SCREW
SCOUT DECK ANCHOR 16" 16" 1" X 4" ANCHOR BOLT (4) 10" 3 1/8" 5" 6" MIN COPPER WIRE TO ATTACH TO BONDING GRID 3 1/4" BONDING SCREW CONCRETE DECK SPECIFICATIONS: THE AQUA CREEK PRODUCTS' SCOUT DECK ANCHOR
More informationDEADLATCHES LK-2100 SERIES ASSEMBLY DETAILS LK R-RH
LK-2100-40-R-RH 7:07 2 x csk. holes to suit M5 LK-2100-40-R-RH Right hand door FX079XSLF x 4 1 LK-2100-70 LK-2100-70 AC021 LK-2100-40-R-RH 2 3 4 Complete assembly should consist of:- LK-2100-40-R-RH Lock
More informationBike Rack and Tire Carrier
Bike Rack and Tire Carrier OWNER'S MANUAL Rev: 10.26.2017 Page 1 Bike Rack and Tire Carrier Owners Manual TABLE OF CONTENTS System 2 Description 2 Prior To Operation 3 Manual Slide-Out Bike Rack Operation
More informationLadies Shopper Bike Assembly Manual 28C03
Ladies Shopper Bike Assembly Manual 28C03 Ecosmo Ltd 1 Know your bike 1. Wheel 2. Rear Derailleur 3. Chain 4. Crank Set 5. Pedal 6. Seat Quick Lock 7. Saddle and Post 8. Frame 9. Front Light 10. Front
More informationSAMPLE PAGE. Section 2... Wire Rope
Section 2...................................................... Wire Rope Never use any kind of clip to directly connect two straight lengths of wire rope to form a continuous piece. Do not make up slings
More informationInstallatIon and owner s InstrUCtIons
InstallatIon and owner s InstrUCtIons Wall Mount Series Adjustable and Fixed Height Goal Systems table of Contents Safety Instructions... 2 Goal Specifications... 3 Frame Attachment... 4 Frame Assembly
More informationAssembly Guide ST200 FUNCTIONAL TRAINER
Assembly Guide ST200 FUNCTIONAL TRAINER Assembly Guide ST200 FUNCTIONAL TRAINER To avoid possible damage to this Functional Trainer, please follow these assembly steps in the correct order. Before proceeding,
More informationASSEMBLY MANUAL HOBIE CATSY
ASSEMBLY MANUAL HOBIE CATSY HOBIE CAT EUROPE ZI Toulon Est, BP 50 8078 Toulon cedex 9, France Tel : + (0)9 08 78 78 - Fax : + (0)9 08 99 Email : hobiecat@hobie-cat.net - http://www.hobie-cat.net ASSEMBLY
More informationX-6FC STRINGING MACHINE OWNER'S MANUAL. Issue 1 - May Copyright 2004 GAMMA Sports - All Rights Reserved
X-6FC STRINGING MACHINE OWNER'S MANUAL Issue 1 - May 2004 Copyright 2004 GAMMA Sports - All Rights Reserved OWNER'S MANUAL GAMMA X-6FC TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3...
More informationEZ-Mount 4 Spring Enclosed System to 22 (Low & High Mount Applications) Installation Instructions
501-1768 (With Wire) 501-1769 (No Wire) 501-1766 (With Wire) 501-1767 (No Wire) 607-015 WLH 06/20/18 TABLE OF CONTENTS ***Assembly*** ***Parts*** Pivot Points and Mounting Locations (Low Mount)... 1 High
More informationWEIGHT STACK ATTACHMENT. Assembly Manual (888) FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
WEIGHT STACK ATTACHMENT Assembly Manual DF835 (888) 258-0533 FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS
More informationSTRINGING MACHINE OWNER'S MANUAL. Issue 5 - November 2012
602 STRINGING MACHINE OWNER'S MANUAL Issue 5 - November 2012 2 602 MP602-12 OWNER S MANUAL TABLE OF CONTENTS WARRANTY... PAGE 3 FEATURES... PAGE 4 ASSEMBLY INSTRUCTIONS... PAGE 5 MOUNTING THE FRAME...
More information#59114 Rola 2-Bike Rack Carrier (Shown Assembled) (A) (C) (B)
Use for Parts: #59114 Rola -Bike Rack System #59115 Rola 1-Bike Add-On TOOLS REQUIRED 10mm or 13/3 Socket & Wrench #59114 Rola -Bike Rack Carrier (Shown Assembled) Tray Attachment Hardware: (3) Plastic
More informationCaliber Sled Wheels Assembly Instructions for PN and 13579
Caliber Sled Wheels Assembly Instructions for PN 13576 and 13579 Caution: Read all instructions before assembling or using Sled Wheels. Follow the steps in order. Only use Sled Wheels as intended, following
More information200 STRINGING MACHINE
200 STRINGING MACHINE OWNER S MANUAL Issue 1 - July 2010 Provided by www.gssalliance.com 200 OWNER S MANUAL TABLE OF CONTENTS WARRANTY...PAGE 2 FEATURES...PAGE 3 ASSEMBLY INSTRUCTIONS...PAGE 4 MOUNTING
More informationASSEMBLY INSTRUCTIONS
XR 9-2009:new odc 1018 revised 2/17/10 9:11 AM Page 1 ODC XR 9 OUTDOOR DISCOVERY CRAFT ASSEMBLY INSTRUCTIONS Your ODC XR 9 Pontoon Boat comes in two separate cartons consisting of the following parts:
More information2012 K9100 COMPACT Worldwide Cycling Solutions Through Creative Innovations.
Home Instruction Sheet Step-1Please check for any missing parts. Model K9100 COMPACT (Basic AirCaddy) aircaddy web page 20 04/03/12 98% (1) T3230-00 METAL WHEEL TRUCK Model K8350 (Aircraft Kit) (Optional)
More information