SVEA II GSM Connector User Manual
|
|
- Gilbert Kelly
- 5 years ago
- Views:
Transcription
1 SVEA II GSM Connector User Manual
2 1. Introduction Before using SVEA II please read this manual carefully and keep it for future reference. SVEA II GSM Connector is a device for realization of voice connections from analog telephones, fax services and for internet access from PC and data transmission. All services are held over GSM network. Picture 1. SVEA II GSM Connector with external devices SVEA II GSM Connector package contains: SVEA II GSM Connector with built in battery Power supply Antenna GSM User Manual Picture 2. SVEA II GSM Connector package 2
3 2. Technical information 2.1. SVEA II GSM Connector specification GENERAL Dimension Weight excl. power supply 210 mm x 200 mm x 55 mm 1385 g ENVIRONMENT SPECIFICATION Operating temperature -10 o C o C Storage temperature -20 o C o C Relative humidity Max. 85% power supply Type Switch mode Input AC V AC, 50/60Hz Output VDC 18V DC Output current 0,8 A Weight 155 g internal antenna Antenna type All-around helical antenna Frequency band / MHz Impendance 50 ΩW Antenna gain 0,0 db VSWR < 2,0 Type of plug Direct for TNC-f battery backup Voltage Capacity Standby time on battery back up Conversation time on battery backup 12 V 2.3 Ah Min. 12 hours Min. 30 minutes 2.5. Technical specification SVEA II GSM Connector Voltage requirement Current consumption Current consumption (Standby) Telephone interface - Impedance - Line voltage - Ringing voltage - Dialing system - Max. quantities of user devices connected to the plug - Max. cable length between device and plug RJ11 11,0 20 VDC Max VDC mA 600 ΩW 48Vdc / nominal 52 VDC +/- 4 V 48 Vrms +/- 8 25/50 Hz DTMF / Pulse One device to one RJ11 plug 500 meter 3
4 Radio interface - Technology - Out power (According to: Release 99, V5) Data transmission Fax transmission Sensitivity of receiver Voice code - Siemens GSM Phase 2+ - Quad band: GSM 850/900/1800/1900MHz - Class 4 (+33dBm ±2dB) for EGSM900 - Class 1 (+30dBm ±2dB) for GSM Class E2 (+27dBm ± 3dB) for GSM PSK - Class E2 (+26dBm +3/-4dB) for GSM PSK The values stated above are maximum limits and can be lower depending on connection. GPRS Multi-slot Class 12 Mobile Station Class B EGPRS Multi-slot Class 12 Mobile Station Class B CSD Group 3; Class BER Class II < 2.4% E-GSM 900 min.: -102 dbm usually: -108 dbm GSM 1800 min.: -102 dbm usually: -107 dbm ETS06.10/(ETS 06.10) (Full rate), ETS06.50/06.60/06.80 (Enhanced Full Rate), ETS06.20/(ETS 06.20) (Half rate) and Adaptive Multi Rate AMR 3. General description 3.1. Cabinet External antenna cable hole USB Fax/Data Phone Power Picture 3. SVEA II connectors 3.2. External devices plugs Power plug for power supply, which converts 220V/230V voltage to 18V voltage. Do not use other power supplies than the one that was originally supplied with SVEA II. Other power supplies can damage SVEA II. 1. TELEPHONE plug - RJ11 for analog telephone with DTMF or Pulse. 2. FAX/MODEM plug - RJ11 for analog fax machine G3 or analog modem V RS232 port - for programming SVEA II GSM Connector only for authorized person. 4. USB port - not active. Contact Possio for more information. When you connect or disconnect power cable always hold the plug and not the cable. 4
5 3.3. LED signalization SVEA II GSM Connector has 3 built-in LEDs that show status of interface work. SIGNAL Color State GSM signal level Red Yellow Green Flashing Constant Flashing Constant Flashing Constant Very poor or out of GSM net RSSI < -85dBm Poor -85dBm =< RSSI < -80dBm Accepted -80dBm =< RSSI < -75dBm Medium -75dBm =< RSSI < -70dBm Good -70dBm =< RSSI < -65dBm Very good RSSI => -65dBm STATUS Color State Status Red Constant Terminal not on GSM network or SIM card error Green Constant Connected to network / terminal ready to use STATUS, TELEFON line Green Flashing (0.4s/0.4s) Connected to network Telephone line off hook Yellow Flashing (0.4s/0.4s) Telephone dial up to GSM network in progress Yellow Constant Conversation established STATUS, FAX/MODEM line Green/ /Yellow/ Flashing (0.4s/0.4s/0.4s/ Connected to network 0.4s) Fax/Data line off hook Yellow/Green Flashing (0.4s/0.4s) Data/Fax Dial up to GSM network in progress Yellow/Green Flashing (1.6s/0.4s) Data/Fax call established POWER Color State Type of power Green Constant Normal power Red Constant Battery power Red Flashing Battery power (Low battery) 5
6 4. Internal elements description 4.1. Internal elements Internal antenna GSM or wire for external antenna Battery backup PCB Picture 4. Elements of SVEA II GSM Connector 4.2. Alarm switch SVEA II has an alarm switch built into the PCB board that senses an unauthorized opening of the terminal. In case of unauthorized opening, SVEA II can send an alarm to Management Center with information about such an event. This information is also shown via LED signalization; POWER LED is flashing: green-yellow, if SVEA II is connected to power supply or red yellow when terminal is operating on battery backup. Cover must be fully closed for the unit to be operational Holes for mounting Picture 5. Holes for terminal mounting 4.4. Battery backup The battery backup is not connected at delivery. The battery should be connected during SVEA II installation. During the first start of SVEA II GSM Connector with battery backup, SVEA II should be connected to power supply for min. 48 hours. If there is a power break while SVEA II is working, the battery shall be recharged for min. 24 hours. In case of power failures, SVEA II will automatically switch to battery backup. A new battery should be used when standby and conversation time of battery backup is shortened (see: battery backup). Picture 6. Battery backup 6
7 Battery recycling The battery should not be disposed with unsorted household waste. Improper disposal may be harmful to the environment and human health. Please refer to your local waste authority for information on return and collection systems in your area Antenna Depending on the GSM signal level at installation site, a suitable antenna should be chosen to provide correct terminal functionality. SVEA II GSM Connector can work both with the internal and/or an external antenna. Internal antenna An internal helical GSM antenna is provided with terminal; See 2.3 for specification of this antenna. External antenna External GSM antenna for terminal shall fulfill requirements as below. Parameters of external antennas Parameters Type of antenna All-around and direction antenna with specification suitable for installation site Frequency band / MHz Impedance 50 ohm VSWR < 2,0 Type of connector TNC-f Recommended type of antenna cable H155, RLF-7 or other with the same or better spefication When you are using external antenna follow all rules of external antenna manufacturer. If you notice that the antenna or antenna cable is damaged, contact your reseller. Do not change the antenna or antenna cable by yourself. Do not touch the antenna or antenna cable if it is damaged. Avoid standing close to the antenna, when SVEA II is working. Keep a min. distance of 30cm. This distance can be different depending on antenna type. Picture 7. Example of mounting the external antenna For direction antennas with gain more than 3 db, see the safety distance below. Picture 8. Safe distance for antenna with gain 8 db and 20 db. 7
8 5. Installation and safety precautions 5.1. Place of installation SVEA II shall only be used inside buildings and cannot be exposed to humidity, sun or to high and low temperatures. SVEA II GSM Connector shall be installed at least 30cm / 12 inches from people. The distance between SVEA II and other devices connected to SVEA II shall be a minimum 3 meters. Space around terminal shall be free; terminal needs to be ventilated when working. Any heating devices (like radiator, stove) cannot be placed close to SVEA II. SVEA II shall be mounted with screws to mounting holes. SVEA II shall be mounted vertically on flat and hard surface. Picture 9. Example of SVEA II installation 5.2. Safety precautions Should an external antenna be used, please install the telephone cable away from the antenna cable. Do not dismantle and do not drop SVEA II. Battery backup is part of SVEA II. Do not dismantle the battery, because it contains materials that can cause burns to skin. Do not throw the battery into fire, because it can explode. Protect SVEA II against dust. Non-original antennas may have negative influence for RF signal transmission. Using the non-original antennas or connecting other devices can damage SVEA II. If terminal is repaired by a non-authorized person, SVEA II loses all warranty. Only the outside part of SVEA II cabinet can be cleaned. Use a dry and soft cloth only. Do not use cleaning alcohol, acetone, caustic chemicals, solvent, and any scrub powder, which can damage the plastic casing. 8
9 6. Calling 6.1. Voice services outgoing calls Telephone connected to TELEPHONE plug. 1. Pick up telephone handset, you will hear dial tone. If terminal is not ready you will hear a busy tone or a non-available tone. 2. Dial the number (DTMF/PULSE). If you press # the number will be sent to network immediately. Without pressing # number will be sent automatically after 7 seconds. 3. SVEA II sets the connection with defined number. 4. Hang up to end connection Voice services incoming calls Telephone connected to TELEPHONE plug. 1. After receiving information about incoming calls, terminal sends ringing tone to TELEPHONE plug. 2. Pick up telephone handset and start your conversation. 3. Hang up to end connection Additional services Telephone connected to TELEPHONE plug. 1. Pick up telephone handset, you will hear dial tone. If terminal is not ready you will hear a busy tone or a non-available tone. 2. Choose a code of additional service via DTMF. You cannot use PULSE mode for these services. 3. SVEA II receives service code from user and sends to network operator. 4. Hang up to end connection FAX services outgoing calls Fax connected to FAX/MODEM plug. 1. Sequence the same as in voice calls FAX services incoming calls Fax connected to FAX/MODEM plug, calls incoming on additional number for fax calls. It is recommended to set fax on automatic receiving mode. 1. After receiving information about incoming calls, SVEA II sends ringing tone to FAX/MODEM plug. 2. After answering the call, fax machine starts receiving the fax message Internet connection Dial-up Telephone modem connected to FAX/MODEM plug. 1. Choose (DTMF/PULSE) a number of ISP (Internet Service Provider). 2. Terminal sets the connection Data transmission outgoing calls Telephone modem connected to FAX/MODEM plug. 1. Pick up line to get a dial tone. 2. Choose a number (DTMF/PULSE) preceding 1*. If you press # the number will be sent to network immediately. Without pressing # number will be sent automatically after 7 seconds. 3. SVEA II sets the connection with defined number. 4. Hang up to end connection Data transmission incoming connections Telephone modem is connected to FAX/MODEM plug, calls incoming on additional number for data transmission. 1. After receiving information about incoming calls, SVEA II sends ringing tone to FAX/MODEM plug. 2. SVEA II sets the connection. For fax calls the minimum GSM signal shall be on medium level according to table in 3.3 SIGNAL LED. Realization of voice connection is not possible via FAX/MODEM connector. 9
10 7. Troubleshooting Problem with noise during connection Move connected devices away from SVEA II, and in case of using an external antenna move it also away at least 3 metres/ 10 feet from antenna and antenna cable. Problem with signal on line TELEPHONE and/or FAX/MODEM: Make sure that SVEA II is connected to power supply or battery backup (see 3.3 LED signalization). Make sure that signal level is strong enough (SIGNAL LED). Make sure that cables between terminal and connected devices are connected correctly and that they are not damaged. If device is connected to SVEA II correctly, make sure that SVEA II is reacting correctly for on Hook / Off Hook state (see 3.3 LED signalization). If SVEA II shows correct state but there is no signal (contact your operator). Problem with CLIP presentation: Make sure that telephone connected to SVEA II, services the FSK signalization standard. You can find this information in the user manual of analog telephone. Contact your operator, to find if CLIP FSK service is activated. Problem with additional services offered by operator: Contact your operator to find if additional service is activated for your SVEA II. Using the additional services is possible only via DTMF mode. Make sure that telephone connected to terminal is in DTMF mode. Problem with sending / receiving fax: Make sure that fax machine is connected to the FAX/MODEM plug. Contact your operator to find if sending/receiving fax message service (i.e CSD-fax ) is activated for your SVEA II and if you have an additional dedicated number for fax. Switch the fax machine to automatic mode and try once again to send /receive fax message. Make sure that SIGNAL LED shows correct GSM signal level recommended for realization of fax service. Problem with data transmission: Make sure that the modem is connected to FAX/MODEM plug. Contact your operator to find if data transmission service is active for your SVEA II and if you have additional number for data transmission. 8. Information about safety SVEA II GSM Connector uses the general GSM standard, like typical mobile phones Electronic equipment Although most of electronic equipment is well protected from RF signals, RF signals may interfere with some devices. In some cases the signal from SVEA II or external antenna, can interfere with medical equipment e.g. hearing aid. If you notice problems please read the instruction of your device. In case of using other medical equipment contact your doctor or manufacture of equipment, to make sure that your equipment is well protected from RF signals Usage Power cable and other cables connected to SVEA II shall always be installed in a proper way. Do not let children touch SVEA II and cables that are connected to terminal. If you notice that power cable is damaged, inform your reseller. Do not change the cable yourself. Non-original cable can caused damages to SVEA II. It can also be dangerous to the user. Recycling SVEA II should not be disposed with unsorted household waste. Improper disposal may be harmful to the environment and human health. Please refer to your local waste authority for information on return and collection systems in your area. 10
SonoMeter 30 Energy Meters
Data Sheet SonoMeter 30 Energy Meters Description The Danfoss SonoMeter 30 is a range of ultrasonic, compact energy meters intended for measuring energy consumption in heating and cooling applications
More informationPortable oxygen concentrator
Table of contents G3 1. Introduction 2 2. Important Safety Rules 3 3. Unpack your Lovego 4 4. User Controls & System Status Indicators 5 5. Quick Start 6 6. How to operate 7 7. How to operate with battery
More informationCertification Exhibit FCC ID: R7PIWRS4. FCC Rule Part: ACS Report Number: W03.11.A
Certification Exhibit FCC ID: R7PIWRS4 FCC Rule Part: 15.247 ACS Report Number: 09-0412.W03.11.A Manufacturer: Cellnet Technology Inc. Model: Gridstream DCIWR Manual 5015 B.U. Bowman Drive Buford, GA 30518
More informationA4 Operation Manual. Fig.1-1 Controller Socket Diagram
A4 Operation Manual Safety Instruction Please read this manual carefully, also with related manual for the machinery before use the controller. For installing and operating the controller properly and
More informationJOLLY2. Installation user s manual. 6 different operating modes selectable. version 3.3. DATA TO BE FILLED OUT BY THE INSTALLER (Page 1)
ENGLISH ENGLISH ENGLISH ENGLISH Installation user s manual Warning! electrical scheme modified JANUARY 2005 version 3.3 JOLLY2 DATA TO BE FILLED OUT BY THE INSTALLER (Page 1) 6 different operating modes
More informationMAGICFX CONFETTIPISTOL USER AND INSTALLATION MANUAL
English MAGICFX CONFETTIPISTOL USER AND INSTALLATION MANUAL CONFETTI FX / STREAMER FX Manual trigger PART01129 rev 01-00 DISCLAIMER WARNING Read this manual carefully before installing and/or using this
More informationA4s Operation Manual
A4s Operation Manual Safety Instruction Please read this manual carefully, also with related manual for the machinery before use the controller. For installing and operating the controller properly and
More informationAchat 112 mid-high-range speaker. user manual
Achat 112 mid-high-range speaker user manual Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de
More informationHyperSecureLink V6.0x User Guide
HyperSecureLink V6.0x User Guide Note: This software works with the LS-30 Version (06.0x or later) 1, Hardware Installation: 1-1, Connection Diagram for USB or RS-232 Computer Interface To LS-30 CM1 To
More informationPROPORTIONING VALVE. Model 150 INSTRUCTION MANUAL. March 2017 IMS Company Stafford Road
PROPORTIONING VALVE Model 150 INSTRUCTION MANUAL March 2017 IMS Company 10373 Stafford Road Telephone: (440) 543-1615 Fax: (440) 543-1069 Email: sales@imscompany.com 1 Introduction IMS Company reserves
More informationOperating Instructions Part No
DIGITAL AUTOMATIC TYRE INFLATOR Operating Instructions Part No. 11.0545 Thank you for selecting this Jamec Pem Automatic Tyre Inflator. Please read this manual before carrying out any installation or service
More informationOperating instructions Safety Rope Emergency Stop Switches ZB0052 / ZB0053 ZB0072 / ZB0073
Operating instructions Safety Rope Emergency Stop Switches UK ZB0052 / ZB0053 ZB0072 / ZB0073 7390878 / 02 03 / 2011 Contents 1 Safety instructions...3 2 Installation / set-up...4 2.1 Applications...4
More information1. Functional description. Application program usage. 1.1 General. 1.2 Behavior on bus voltage loss and bus voltage. 1.
Application program usage product family: Product type: Manufacturer: Name: Order-No.: Valve actuators Constant valve actuator Siemens Valve actuator AP 562/02 5WG1 562-7AB02 Commissioning For commissioning
More informationOperating Instructions Part No
DIGITAL AUTOMATIC TYRE INFLATOR Operating Instructions Part No. 11.0578 Thank you for selecting this Jamec Pem Automatic Tyre Inflator. Please read this manual before carrying out any installation or service
More informationApollo Safety Features
Overview of Emergency Start Mains Power Failure Gas Supply Failure Ventilator Failure Fresh Gas Delivery Failure Ventilator and Fresh Gas Delivery Failure Display Failure User Interface Failure System
More informationBUDDY Gorgeous and easy to use GPS Navigation Kit USER GUIDE. Love from Intempo Digital xx
BUDDY Gorgeous and easy to use GPS Navigation Kit USER GUIDE Love from Intempo Digital xx Contents - What s in the box 1. Buddy with Styli touch screen pen 2. Buddy holder 3. USB cable 4. Car charger 5.
More informationWireless Belt Pack BP Conductor with Radio Transmit
Wireless Belt Pack BP5-10 5-Conductor with Radio Transmit Operation Manual 7340 SW Durham Road Portland, OR 97224 USA Phone: 503-684-6647 1-800-527-0555 Fax: 503-620-2943 email: sales@firecom.com www.firecom.com
More informationUser s Manual. Copyright 2014 Trick Technologies Oy
User s Manual Copyright 2014 Trick Technologies Oy Catchbox Pro Module Catchbox Cover Contents 1 Safety Instructions...4-5 2 Quick Start... 6-15 3 Product Description... 16-18 Overview...16 Compatibility...17
More informationWireless Belt Pack BP Conductor Jack with Radio Transmit & Volume Control
Wireless Belt Pack BP3-10 3-Conductor Jack with Radio Transmit & Volume Control Operation Manual 7340 SW Durham Road Portland, OR 97224 USA Phone: 503-684-6647 1-800-527-0555 Fax: 503-620-2943 email: sales@firecom.com
More informationInstruction Manual BA90 Precision Barometer
Instruction Manual BA90 Precision Barometer halstrup-walcher GmbH Stegener Straße 10 D-79199 Kirchzarten Germany Phone: +49 (0) 76 61/39 63 0 Fax: +49 (0) 76 61/39 63 99 E-Mail: info@halstrup-walcher.com
More informationSensoric 4-20 ma Transmitter Board Operation Manual
Sensoric 4-20 ma Transmitter Board Operation Manual 1 Content Features Operation Manual Technical Data Mechanical Dimensions Remarks & Contact information 2 Features Soldered sensor cell (non replaceable)
More informationSPECIFICATION. Product Name : MA450 Storm 5in1 Permanent Mount Antenna LTE MIMO*2 + WIFI MIMO*2 + GNSS
SPECIFICATION Part No. : MA45.K.LBICG.3 Product Name : MA45 Storm 5in1 Permanent Mount Antenna LTE MIMO*2 + WIFI MIMO*2 + GNSS Features : Aerodynamic, Super Low-profile Vandal Resistant Housing 2* LTE
More informationSECTION 2 SMART PAYOUT MANUAL SET FIELD SERVICE MANUAL
SECTION 2 SMART PAYOUT MANUAL SET FIELD SERVICE MANUAL Innovative Technology assume no responsibility for errors, omissions, or damages resulting from the use of information contained within this manual.
More informationKERN EG/EW Version /02
E KERN EG/EW Version 1.5 07/02 Operating Instructions Electronic Precision Balances Contents 1 TECHNICAL DATA... 20 2 UNPACKING AND STANDARD ACCESSORIES... 23 3 SETTING UP THE BALANCE... 23 4 EXTERNAL
More informationBUBBLER CONTROL SYSTEM
BUBBLER CONTROL SYSTEM Description: The HDBCS is a fully automatic bubbler system, which does liquid level measurements in water and wastewater applications. It is a dual air compressor system with, air
More informationSensor for Air Bubble Detection at Liquid Filled Tubes. SONOCHECK Type ABD06.xx. Operating Manual
Sensor for Air Bubble Detection at Liquid Filled Tubes SONOCHECK Type ABD06.xx Operating Manual Manufacturer: Model: Type: SONOTEC Ultraschallsensorik Halle GmbH Air Bubble Detector ABD06.xx SONOTEC Ultraschallsensorik
More informationBUBBLER CONTROL SYSTEM
BUBBLER CONTROL SYSTEM Description: The LDBCS is a fully automatic bubbler system, which does liquid level measurements in water and wastewater applications. It is a dual air compressor system with, air
More informationSDX Submersible Depth Transmitter User Manual
SDX Submersible Depth Transmitter User Manual July 2017 USER INFORMATION Stevens makes no warranty as to the information furnished in these instructions and the reader assumes all risk in the use thereof.
More informationSDX Submersible Depth Transmitter User Manual
SDX Submersible Depth Transmitter User Manual October 2007 USER INFORMATION Stevens makes no warranty as to the information furnished in these instructions and the reader assumes all risk in the use thereof.
More informationRPS900W Redundant Power Supply. Installation Guide.
RPS900W Redundant Power Supply Installation Guide www.edge-core.com Installation Guide RPS900W Redundant Power Supply Single DC Output Port with Dual Output Voltages RPS900W E10013-CS-R01 1500000081A
More informationOperating instructions Capacitive sensor KIA (M30) / / 2010
Operating instructions Capacitive sensor KIA (M30) UK 704182 / 03 07 / 2010 Contents 1 Preliminary note 3 2 Safety instructions 3 3 Functions and features 3 3.1 Application examples 4 4 Installation 4
More informationVERTICAL AIR COMPRESSORS
VERTICAL AIR COMPRESSORS MODEL NO: VE15C150, VE18C150, VE25C150 PART NO: 2226010, 2226020, 2226025 OPERATION & MAINTENANCE INSTRUCTIONS LS0715 INTRODUCTION Thank you for purchasing this CLARKE Vertical
More informationTH-1800-T TRX-700-CNG Converter
TH-1800-T TRX-700-CNG Converter low detector The CNG fuel gas flowmeter is so accurate as to meet a demand of measuring the CNG directly by making the most use of our well-established mini-thermal flowmeter
More informationTEL/jlRE" Introduction. Display Features and Modes. Startup Procedure. Power-Up Procedure. Adjustment Modes
TEL/jlRE" Introduction The Telaire 7001 CO 2 /T emperature monitor (shown in Fi gt u e 1 below) is an easy to use hand-held instnunent, which provides stable and highly accurate readings due to Telaire
More informationRAM 4021-DPX Operation Manual
RAM 4021-DPX Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS ABL 4021-DPX / RAM 4021-DPX For Your Safety... 3 Description... 3 Setup Mode... 4 Lights/Alarms... 4 Operation...
More informationOperating instructions Capacitive sensors KG AC (M18) / / 2010
Operating instructions Capacitive sensors KG AC (M18) UK 704923 / 00 09 / 2010 Contents 1 Preliminary note 3 2 Safety instructions 3 3 Functions and features 3 3.1 Application examples 4 4 Installation
More informationUsER manual for Watersens ph -REDOX
UsER manual for Watersens -REDOX Cl 8 1 2 6 3 3 7 7 4 4 4 4 Parts List 1 Redox Probe 1 x 2 PH Probe 1 x 5 Tube Weight 2 x 6 Connection Valve 1 x chlorine 3 Chlorine and Pumps 2 x 7 Dosing Valve 2 x 5 5
More informationYSC-8330 USER MANUAL XI AN TYPICAL INDUSTRIES CO.,LTD.
YSC-8330 USER MANUAL XI AN TYPICAL INDUSTRIES CO.,LTD. Contents 1 Notice 1.1 Work environment 1.2 Notice of installation 1.3 Notice of safety 2 Installation and Adjustment 2.1 Controll box 2.2 Speed controller
More informationElectronic Volume Correctors
Electronic Volume Correctors Ben Manson Landis+Gyr October 14, 2016 PUBLIC Agenda Customer Types and suitable equipment Volume corrector standards / regulations Basics of volume correction Gauge v Absolute
More informationPLEASE READ CAREFULLY BEFORE INSTALLING OR USING MEGA POOL SAVER MPS 1100
MPS-1100 User Manual Mega Pool Saver Ltd PLEASE READ CAREFULLY BEFORE INSTALLING OR USING MEGA POOL SAVER MPS 1100 For further up to date instructions on how to install Mega Pool Saver MPS 1100, please
More informationSPECIFICATIONS ATTENTION
VPS 504 S06 Installation Manual - P/N 80122 - Ed. 01/09 VPS 504 S06 and S05 Valve Proving System Installation Instructions VPS 1 6 Gases Natural gas, air and other inert gases. NOT suitable for butane
More informationEasySas. The most advanced airlock electronics on the market. Recyclable product. Eco-design. Energy savings
EasySas The most advanced airlock electronics on the market Eco-design Energy savings Recyclable product ELECTRONIC AIRLOCK MANAGEMENT SkySas range UniSas range CompacSas range An electronic management
More informationOperating instructions Installation instructions To be kept in the vehicle!
ON OFF Sonatic Sonatic Level indicator for gas cylinders (Type GB) h Operating instructions Installation instructions To be kept in the vehicle! Service (UK and Eire) Tel. (0 12 83) 51 10 92 Fax (0 12
More informationCONSOLE-320 ENGLISH. 230A: CONSOLE-320 with cable data output Item 230B: CONSOLE-320 with cable + wireless radio data output
CONSOLE-320 Item 230A: CONSOLE-320 with cable data output Item 230B: CONSOLE-320 with cable + wireless radio data output Table of contents 1. INTRODUCTION...2 1.1 Power supply...2 1.2 Connections...2 1.3
More informationSolenoid gas valve. The solenoid gas valve is also applicable as a main gas valve Pilot gas valve for forced draft burners
7 634 VGS1... with AGA67 connector VGS2... with AGA67 connector Solenoid gas valve VGS The solenoid gas valve is also applicable as a main gas valve Pilot gas valve for forced draft burners The VGS and
More informationQPL... Pressure Switches. Siemens Building Technologies HVAC Products
7 221 Pressure Switches QPL... The pressure switches are used for monitoring gas or air pressures. When the pressure falls below the switching point, the associated electrical circuit will open or switch
More informationAUTO PUMP STATUS CENTER
INSTRUCTION MANUAL AUTO PUMP STATUS CENTER PRESSURE ONLY MODEL #: 091-198-12-AP File: IM_091-198-12-AP_revD.indd Rev: D, pg 3 WD Revised By: PSS Date: 2-01-2016 3 YEAR WARRANTY INTRODUCTION The Auto Pump
More informationRAM Operation Manual
RAM 4021-1 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021-1 For Your Safety... 2 Description... 2 Setup Mode... 3 Lights/Alarms... 3 Operation... 4 Calibration...
More informationOC Panel High Limit Aquastat Kit, Manual Reset p/n
OC Panel High Limit Aquastat Kit, Manual Reset p/n 233202 Instruction Sheet APPLICATION The OC (Option Control) Panel High Limit Aquastat Kit provides electronic temperature sensing in a UL limit-rated
More informationMiniature controls. Contactors. Overload relays. Starters. Control relays
Contactors Overload relays Starters Control relays Description General features Wiring terminations available include plugon connectors, wire pins for PC board mounting and solder connections Low power
More informationMass Flow Meter (MFM) for gases
Mass Flow Meter (MFM) for gases Type can be combined with Inline MFM for nominal flow rates from 25 l N /min to 1,500 l N /min; 1/4 to 3/4 High accuracy Fast settling time Fieldbus option Special version
More informationPre-filter for Brushless Blower Instruction Manual
Pre-filter for Brushless Blower 781-70-702 Instruction Manual Minebea Co., Ltd. Industrial Machinery Business Unit 251-8531 1-1-1 Katase,Fujisawa,kanagawa Contact Us Industrial Machinery Product Sales
More informationINSTRUCTION MANUAL Auto Purge System
INSTRUCTION MANUAL Auto Purge System content 1. Safety instructions 2. Description 3. Assembly and installation 4. Delivery items 5. Technical data 6. CE-Document 1. Safety instructions Read the safety
More informationSTAGE, STADIUM & X-TREME SHOT.
USER AND INSTALLATION MANUAL ENGLISH STAGE, STADIUM & X-TREME SHOT. CONFETTI & STREAMER FX PART01339 rev 01-00 DISCLAIMER WARNING Read this manual carefully before installing and/or using this product.
More informationDIY - PC - Interface for Suunto Cobra/Vyper/Mosquito
DIY - PC - Interface for Suunto Cobra/Vyper/Mosquito Summary This document is the distinct consequence of the Spyder/Stinger interface DIY. After having many e-mails concerning the application for the
More informationUser's Manual. Heavy Duty Dissolved Oxygen Meter. Model
User's Manual Heavy Duty Dissolved Oxygen Meter Model 407510 Introduction Congratulations on your purchase of Extech's Heavy Duty Dissolved Oxygen / Temperature Meter which simultaneously displays Dissolved
More informationVortex Flow Sensor VA Di Ex-d for flow measurement in gases; with integrated, configurable transducer UVA in Ex-d housing
Vortex Flow Sensor VA Di Ex-d Vortex Flow Sensor VA Di Ex-d for flow measurement in gases; with integrated, configurable transducer UVA in Ex-d housing Drawing 1 Measurable variables actual flow rate actual
More informationBASnet LightiView Install Guide
BASnet LightiView 1025 Cobb Place Blvd Suite 100 Kennesaw, GA 30144 800-241-9173 www.triateklighting.com ATTENTION This section serves as a notice of the immediate or potential dangers involved when working
More informationDatasheet: K-30 ASCII Sensor
Datasheet: K-30 ASCII Sensor The K30 ASCII sensor is a low cost, infrared and maintenance free transmitter module intended to be built into different host devices that require CO2 monitoring data. The
More informationAlphasense 4-20 ma transmitters offer convenience and easy maintenance for toxic sensors:
ALPHASENSE USER MANUAL Page 1 4-20mA Transmitter for Toxic Sensors UMTOX-1 Issue 4 1 INTRODUCTION The Transmitter PCB includes circuitry for a three electrode toxic sensor to convert the µa output signal
More informationWF STEUERUNGSTECHNIK GMBH. INFORMATION and TECNICAL DESCRIPTION
1 INFORMATION and TECNICAL DESCRIPTION 14 2 AIRLEADER Professional Compressor Management + Compressed Air Visualisation + Alarm Service Management + AIRLEADER - has been the effective answer for compressed
More informationMOTOROLA PTP 800 LICENSED ETHERNET MICROWAVE
HIGH-THROUGHPUT COMMUNICATIONS FOR MULTI-SERVICE NETWORKS MOTOROLA PTP 800 LICENSED ETHERNET MICROWAVE PTP 800 solutions can efficiently and affordably transport the data, voice and video that your bandwidth-intensive
More informationLK-SX CO 2 +VOC. Application. Security Advice Caution. Notes on Disposal
LK-SX CO 2 +VOC Sensor for detection of carbon dioxide (CO 2) and mixed gas content in air ducts Data sheet Subject to technical alteration Issue date: 24.08.2015 Application For detection of CO2 and VOC.
More information9A5N Solid State CW Paddle
9A5N Solid State CW Paddle User manual Table of contents: 1. General description 2. Before you begin 3. Finger piece and/or battery installation 4. Interconnection 5. Lever(s) sensitivity adjustment 6.
More informationThe Univentor 1250 Anaesthesia Unit
THE UNIVENTOR 1200/1250 ANAESTHESIA UNIT The Univentor 1250 Anaesthesia Unit TABLE OF CONTENTS EDITION 1 Section 1 - WARRANTY & SERVICE 1.1. WARRANTY 2 1.2. DAMAGED SHIPMENTS 2 1.3. SERVICE 2 Section 2
More informationVERTICAL AIR COMPRESSORS
VERTICAL AIR COMPRESSORS MODEL NO: VE11C150, VE15C150, VE18C150 PART NO: 2226005, 2226000, 2226015 OPERATION & MAINTENANCE INSTRUCTIONS LS0615 INTRODUCTION Thank you for purchasing this CLARKE Vertical
More information! Warning, refer to accompanying documents.
About this Manual To the best of our knowledge and at the time written, the information contained in this document is technically correct and the procedures accurate and adequate to operate this instrument
More informationRoller AC Servo System
Safely Instruction Roller AC Servo System HMI-15 User Manual Please read this manual carefully, also with related manual for the machinery before use the controller. For installing and operating the controller
More informationLK-SX VOC. Application. Security Advice Caution. Notes on Disposal. Combined sensor mixed gas. Data sheet
LK-SX VOC Combined sensor mixed gas Data sheet Subject to technical alteration Issue date: 24.08.2015 Application The sensor detects air quality in ventilation ducts. A stronger output signal of the sensor
More informationOperating Instructions of BROSA tension load cells, types 0111, 0113
Operating Instructions of BROSA tension load cells, types 0, 03. Description of BROSA tension load cells. Structure and function The BROSA type 0 and 03 tension load cells transmit and measure the tensile
More informationAutocalibration Systems For In Situ Oxygen Analyzers
Product Data Sheet PDS 106-340AC SPS 4000, IMPS 4000, and MPS 3000 January, 1999 Autocalibration Systems For In Situ Oxygen Analyzers Cost-effective autocalibration systems for installations ranging from
More informationSystem Introduction. Specifications. Expansion Cards
System Introduction Section 1 Specifications Central Processor Board Eight stations, expandable to 24 Two telephone lines, expandable to eight A 100 call log of caller name,* number,* time and date of
More informationGas Pressure Switch for DMV safety shutoff valves
Gas Switch for DMV safety shutoff valves GAO-A GMH-A GML-A UL Listed UL 353 File # MH 1668 CSA Certified CSA C. No. LR 53 File # 0157 FM Approved Class 3510, 3530 File # J.I. 1Y9A9.AF Commonwealth of Massachusetts
More informationInstruction Manual Differential Pressure Transmitter
DE61 Instruction Manual Differential Pressure Transmitter Table of Contents 1. Safety Instructions 2. Intended Applications 3. Product Description and Functions 4. Installation 5. Commissioning 6. Maintenance
More informationEC214 EC215 - EC215R Bench Conductivity Meters
Instruction Manual EC214 EC215 - EC215R Bench Conductivity Meters http://www.hannainst.com These Instruments are in Compliance with the CE Directives Dear Customer, Thank you for choosing a Hanna Instruments
More informationFTS SUBMERSIBLE PRESSURE TRANSMITTER USER S MANUAL
FTS SUBMERSIBLE PRESSURE TRANSMITTER USER S MANUAL TABLE OF CONTENTS PRODUCT OVERVIEW 2 I - USE AND CARE: 3 II - INSTALLATION: 5 III - GENERAL MAINTENANCE TIPS: 5 IV - APPENDIX: A-1 2-WIRE CURRENT LOOP
More informationSonoSelect 10 and SonoSafe 10 energy meters
SonoSelect 10 and SonoSafe 10 energy meters Description The Danfoss SonoSelect 10 and SonoSafe 10 are ultrasonic compact energy meters intended for measuring energy consumption in heating and cooling applications
More informationTransmitter CS 21 Operation Manual
Transmitter CS 21 Operation Manual Content Page For your Safety 3 General Description 3 Detection Principle 4 Operational Notes 4 Design 4 Mounting Position of CS21 5 Mounting 6 Installation of Electrical
More informationWELCOME TO THE REVOLUTION
USER GUIDE WELCOME TO THE REVOLUTION THANK YOU FOR CHOOSING THE GCQUAD We listened to what you wanted - and created the most accurate, versatile and game-enhancing ball and club analysis solution available
More informationTransmitter CS 21 Operation Manual
Transmitter CS 21 Operation Manual 1194 Oak Valley Drive, Suite 20, Ann Arbor, MI 48108 800-959-0573 734-769-1888 Content Page For your Safety 3 General Description 3 Detection Principle 4 Operation 4
More informationRAM Operation Manual. Worldwide Manufacturer of Gas Detection Solutions
RAM 4021 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021 For Your Safety... 2 Description.... 2 Setup Mode.... 2 Lights/Alarms.... 3 Operation.... 4 Calibration....
More informationSPECIFICATION. 3in1 LTE MIMO + GNSS Antenna
SPECIFICATION Part No. : MA250.A.LBI.001 Product Name : Sentinel Adhesive Mount 3in1 LTE MIMO + GNSS Antenna Feature : Ideal for IoT and Automotive Applications Smallest High Performance MIMO 2 x LTE 4G/3G/2G
More informationResusci Anne Simulator
EN Resusci Anne Simulator Important Product Information www.laerdal.com Cautions and Warnings A Caution identifies conditions, hazards, or unsafe practices that can result in minor personal injury or damage
More informationUser Manual V14.1 IP68 LED FLEX NEON
User Manual V14.1 IP68 LED FLEX NEON PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION LEAVE A COPY FOR THE END USER/MAINTENANCE ENGINEER FOR FUTURE REFERENCE 1/11 PRODUCT SPECIFICATION 1. Operating
More informationPTP 800 SPLIT-MOUNT SOLUTION
TM PTP 800 SPLIT-MOUNT SOLUTION LICENSED ETHERNET MICROWAVE FOR MULTI-SERVICE NETWORKS Cambium Point-to-Point (PTP) 800 Licensed Ethernet Microwave Solutions can efficiently and affordably transport the
More informationHS653 Negative Pressure Ventilation Controller
HS653 Negative Pressure Ventilation Controller General Installation Notes: Make sure that power is disconnected from system prior to servicing. Installation of this equipment and related OEM equipment
More informationE8AA. Pressure Sensor of Stainless Steel Construction Is Ideal for a Wide Range of Applications. Pressure Sensor (Stainless Steel Diaphragm)
Pressure Sensor (Stainless Steel Diaphragm) CSM DS_E_3_1 Pressure Sensor of Stainless Steel Construction Is Ideal for a Wide Range of Applications Incorporates double diaphragms consisting of SUS316L stainless
More informationRAM 4021-PR. Operation Manual. Worldwide Manufacturer of Gas Detection Solutions
RAM 4021-PR Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021-PR For Your Safety... 2 Description.... 2 Setup Mode.... 2 Lights/Alarms.... 3 Operation.... 4
More informationGas Pressure Switch for DMV safety shutoff valves
Gas Switch for DMV safety shutoff valves GAO-A GMH-A GML-A UL Listed UL 353 File # MH 1668 CSA Certified CSA C. No. LR 53 File # 0157 FM Approved Class 3510, 3530 File # J.I. 1Y9A9.AF Commonwealth of Massachusetts
More informationI/P Transducer Positioner Module
I/P Transducer Positioner Module VRC P/N: 7958032 Installation, Operation and Maintenance Instructions 2.09 [53.1] 1.30 [32.9] 2.97 [75.5] 0.78 [19.8] 0.18 [4.4] 1.42 [36.1] n.18 MOUNTING HOLES (2) PLACES
More informationCCT-7320/ROC-2313 Reverse Osmosis Controller
CCT-7320/ROC-2313 Reverse Osmosis Controller 1 General The instrument is a combined control instrument of a reverse osmosis controller and an on-line conductivity instrument. It can perform the operation
More informationElectronic gas volume corrector model DGVC-04
Electronic gas volume corrector model DGVC-04 1. Introduction The following user s manual gives information about the installation, configuration, usage and storage of the electronic gas volume corrector
More informationRAM 4021 Operation Manual
RAM 4021 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021 For your safety...3 Description...3 Set-up mode...4 Annunciator lights/alarms...4 Operation...5 Calibration...6
More informationMEDIANA HEARTON AED A15. Mediana Automated External Defibrillator A15
AED A5 Mediana Automated External Defibrillator A5 AED A5 COVER Protected icon sheet, shock button, adult/paediatric mode switch. 7 BATTERY Disposable LiMnO2 Non-Rechargeable. 2yrs shelf life, 5yrs standby
More informationElectro-Pneumatic Converter YT-940 SERIES
Electro-Pneumatic Converter YT-940 SERIES PRODUCT MANUAL VERSION 1.00 Contents 1. Introduction 3 1.1 General information for the users. 3 1.2 Manufacturer Warranty 3 1.3 Explosion Proof Warning. 4 2. Product
More informationMETEOR LSR36500 LIGHTING UNDERWATER POOL LIGHT. Operating Instructions
METEOR LSR36500 UNDERWATER POOL LIGHT Operating Instructions LIGHTING CONTENTS Preface...3 Features...3 Precautions...3 Components and Connectors...4 Installation...5 Controls...7 Appearance...8 Technical
More informationInstallation & Maintenance Instructions TEC-11N TIMER. Analogue electronic timer 02/09
Installation & Maintenance Instructions TEC-11N TIMER Analogue electronic timer 02/09 GENERAL OPERATION The TEC-11N timer is produced using SMT (Surface Mounting Technology), ensuring improved performance
More informationInstallation and Operation Manual
Manual Static pressure transducer with controller Differential static pressure transducer with analog output and optional PI control mode Large diaphragm element with differential transformer Transducer
More informationACCUSTRIDE ACCUSTRIDEFM. Digital Clip-on Pedometer WC153. Digital Clip-on Pedometer WC154 ENGLISH
ACCUSTRIDE Digital Clip-on Pedometer WC153 ACCUSTRIDEFM Digital Clip-on Pedometer WC154 ENGLISH CONTENTS INTRODUCTION USE OF PEDOMETER 4 BASIC FEATURE 5 TIME MODE 7 WALK / RUN MODE 9 MEMORY MODE 11 USER
More informationVerdi G-Series Family
Verdi G-Series Family High-Power Pumps for Ti:Sapphire Lasers and Amplifiers Applications such as ultrafast spectroscopy, multiphoton microscopy, terahertz imaging, and Optical Coherence Tomography (OCT)
More information