Murray Felstead s modifications to Mark 3 Murranji Tvan to simplify re-assembly.
|
|
- Adela Craig
- 5 years ago
- Views:
Transcription
1 Murray Felstead s modifications to Mark 3 Murranji Tvan to simplify re-assembly. I think all Tvan owners would agree that you do need a fair amount of upper body strength to fold up a Tvan. Lifting the canvas up into the lid section, especially if the canvas is wet, can take a bit of effort. Also, as we all age, we might find the re-assembly progressively more difficult, and we all want to be able to keep our Tvans, don t we? If we have trouble in later years with the re-assembly, we may have to sell it. With this in mind, I have made a couple of simple and fairly cheap modifications to my Mark 3 Murranji, to significantly aid the re-assembly. Firstly, I took my tropical roof to Bartletts, which is the company that makes the canvas for the Tvan. I m lucky I live in Ballarat, where they are located. However, you should find any saddlery store should have the industrial sewing machines to make the modifications. All they did, was add five extra straps with a double loop on each to the tropical roof. (I subsequently realized that the double loop is not required and all one needs to do is just have the five extra straps.) Three, each next to the three clips on the section of the tropical roof that clips to the rings on the tvan roof at the hinge and one on each side of the tropical roof, again next to the clips that clip to the side rings when the tent bottom rear has been pulled up to the side carabiners. These straps will make the process of pulling each clip towards its ring much easier, when the straps are firstly pulled through each ring and then pulled down. I also added a quick grip spring clamp, one extra carabiner to clip on to the carabiner that is permanently attached to the left side of the roof, plus for the pulley system, two extra carabiners, an awning pulley and a few metres of stretch cable, enough to go from the middle of the rear outside floor of the tent, under the tent and up to the centre ring in the roof at the hinge, plus a bit. Five to six metres should be more than enough. And two rings, one ring to pull the cable up and the other to hold the opposite end carabiner in place. The cable has attached a carabiner at one end, and the other end of the cable goes through the pulley and is tied off with a ring. The second carabiner is hooked through the hole in the pulley. See the photos. Most of the photos have an explanation of each component. But basically it does make the whole reassembly process much easier, and the pulling of the tent up into the pocket can be done sitting down on the seat, so it would also be useful if there is bad weather outside. When you arrive in camp, this pulley system will be sitting in the pocket under the lid with the tent, so when letting the tent drop, also watch out for the pulley and carabiners coming down. You don t want them hitting your head! This whole modification was done after one cold, wet morning when I had trouble pulling the clips up to their relative rings. I thought there must be an easier way. This is my solution.
2 This photo shows one of the five extra straps, sewn just next to each of the straps with the plastic clips. The beauty of these straps is that when you are trying to pull the clip up to its ring, it can be difficult to do it without this assistance. Instead, I hoop the strap through the ring that will have the clip attached to it, then pull down on the strap, and simultaneously I can push the canvas tent up to assist getting the clip closer to its ring. This is the simple pulley system. The gold carabiner has a ring attached to it, then this ring has one end of the elastic cord. The other end of the cord loops through the pulley, and, you can t see it clearly in this photo, but there is a ring at this end of the cord. The pulley then has the pink carabiner through its ring. The pulley was bought from the big green hardware store.
3 When in camp, the pink pulley is hooked on the metal bend next to the number plate so it is out of the way. When in camp, the gold end of the pulley sits on the black tvan cord at the back of the tent. The cord in between the gold and pink carabiners is pushed to the side of the floor, so when we walk on the floor inside the tent, the cord cannot be felt.
4 This picture shows the three straps sewn next to the three clips on the section of the tropical roof that, when folding up, attach to the three rings near the hinge of the lid. c I m right handed, and I found when I pull the two rings from the rear top of the tent around to clip onto the carabiners on the side of the lid, the first one (I do the right side first) is easy, but to clip the left side takes a lot more strength. I solved that by adding a second carabiner in line with the carabiner on the left hand side, so that the second ring does not have to be pulled up as far. I don t see a problem here because it is the zips that will soon take the full strain of holding the tent in place. These carabiners are only here to assist to keep the tent up at the lid and to create the pocket for the rest of the tent to placed inside.
5 After attaching the rings to the side carabiners and creating the pocket, I then attach the pink carabiner to the middle ring near the lid hinge, as shown in the photo. I then pull this ring down, remembering that the other end of the cord is attached to the rear middle of the tent, and this process then pulls that other carabiner (the gold one) up towards the location of the pulley, and in the process, pulling the centre bottom of the tent up. During this process, I am sitting down on the seat, just under the rings near the hinge. This avoids the process originally suggested to me of having to grab the corners of the tent and throw the tent into the pocket under the lid. Now, I have pulled the cord as far as it goes, bringing up the gold carabiner which is at the rear centre of the tent, and I use the spring clip (also available from Bunnings) to temporarily hold the assembly in place. I then, still sitting on the seat, push the two bottom corners of the tent, which were dragged behind the gold carabiner, into the pocket, just under the lid. I then remove the spring clip, and allow the middle bottom of the tent, where the gold carabiner is, into the pocket. I then unclip the pink carabiner and also put that into the pocket. I then pull the three straps through their rings and attach the three clips to each ring, and then do up the side and top zips.
a WOW Lab Prep Instructions
Pulleys and Mechanical Advantage A major step in the prep of this activity is choosing a good location. A key feature is an easily accessible top anchor. Some examples of good anchors are a solid tree
More informationTrampoline Installation Instructions
Congratulations on purchasing an Oz Trampolines Product. Following are detailed setup instructions for your trampoline. Please ensure all boxes and parts are present before continuing. Setting Up Your
More informationWing assemblyfinal Master 4/29/04 11:20 PM Page 1. Issued January 1, Sabre Aircraft. Assembly Manual. Sabre 16ss Wing
Wing assemblyfinal Master 4/29/04 11:20 PM Page 1 Issued January 1, 2002 Sabre Aircraft Assembly Manual Sabre 16ss Wing Wing assemblyfinal Master 4/29/04 11:20 PM Page 2 1. 2. 1. Unzip the cover and remove
More informationASSEMBLY MANUAL HOBIE CATSY
ASSEMBLY MANUAL HOBIE CATSY HOBIE CAT EUROPE ZI Toulon Est, BP 50 8078 Toulon cedex 9, France Tel : + (0)9 08 78 78 - Fax : + (0)9 08 99 Email : hobiecat@hobie-cat.net - http://www.hobie-cat.net ASSEMBLY
More informationBuilding a Rocket (Advanced) Before you build a rocket try the bottle on the launcher to test if it holds pressure and fits correctly.
You Will Need 3X 2ltr Bottles 1X Paper lip 1X Glue/Double Sided Tape 1X ardboard 1X Bin Liner 1X Roll of Fishing Line or Thin s Sheets of Paper Side A of Fin 1X Hot Glue Gun 1X Pair of Scissors 1X Fine
More information2010 International Snow Science Workshop
HOW TO TURN A KIDS BIKE INTO A BOMB TRAM FOR AVALANCHE CONTROL WORK David Immeker* Heavenly Mountain Resort Professional Ski Patrol, South Lake Tahoe, California ABSTRACT: Bomb trams have been used for
More informationCamRT Sun Top Bimini Installation Instructions
CamRT Sun Top Bimini Installation Instructions C910-07 & C910-08 Rev. 16-Jun-15 Information: info@roswellglobal.com Warranty: warranty@roswellglobal.com Questions? Please call us at (31) 638-1331 Setup:
More informationStand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS
1 Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new Stand-N-Fish Kayak Fishing System. Once installed on your kayak the Stand-N-Fish will take your kayak fishing
More informationOn the Go Swing System Instruction Manual
On the Go Swing System Instruction Manual WARNING READ ENTIRE MANUAL BEFORE USE. THIS SWING IS NOT A TOY. THIS SWING IS ONLY TO BE USED BY TRAINED PERSONNEL, SUCH AS AN OCCUPATIONAL THERAPIST, PHYSICAL
More informationEUROBUNGY-TRAMPOLINE
EUROBUNGY-TRAMPOLINE Set-up instructions of the new model 2004-2010 Photos are taken with the long and short Trailer WARNING for EUROBUNGIES without hydraulic rams There is a potential risk that a pole
More informationINDEX 1- GENERAL INFORMATION INSTALLATION LEG COVER LEG COVER WITH SPEED-SYSTEM ADJUSTMENT...
INDEX 1- GENERAL INFORMATION... 1 2- INSTALLATION... 2 2.1- LEG COVER... 3 2.2- LEG COVER WITH SPEED-SYSTEM... 5 3- ADJUSTMENT... 8 1- GENERAL INFORMATION LEG COVER is a product that was developed entirely
More informationModel SWGM1791. Sure Shot Lower Game & Net Attachment Users Manual
Model SWGM1791 Sure Shot Lower Game & Net Attachment Users Manual BEFORE YOU BEGIN Thank you for choosing the AZOOGA SPORTS ARENA Sure Shot Game Attachment. The AZOOGA SPORTS ARENA attachments are designed
More informationAssembly Instructions. for. Puffin Saranac. ScanSport, Inc. P.O. Box 700 (234 May Street) Enfield, New Hampshire Phone: (603)
Assembly Instructions for Puffin Saranac ScanSport, Inc. P.O. Box 700 (234 May Street) Enfield, New Hampshire 03748 Phone: (603) 632 9500 Fax: (603) 632 5611 info@pakboats.com www.pakboats.com Assembling
More information2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions
SECTION A: INTRODUCTION This unofficial set of installation instructions was written for a 2009 Hobie Getaway, using a 2012 Hobie Spinnaker Kit 20999020. Note from the Author: I had never seen this kit
More informationSpeedbar parts. Settings
USER MANUAL Speedbar parts Settings 1) Layout setting (First step to the right or left) Default configuration is intended for the right-handed people, so the first pedal was placed to the right to ensure
More informationOn the Go Swing System Instruction Manual
On the Go Swing System Instruction Manual WARNING READ ENTIRE MANUAL BEFORE USE. THIS SWING IS NOT A TOY. THIS SWING IS ONLY TO BE USED UNDER ADULT SUPERVISION. CONSULT WITH A CHILD S THERAPIST ON HOW
More informationFisher and Paykel Aquasmart Washing Machine Suspension Rods Replacement
Fisher and Paykel Aquasmart Washing Machine Suspension Rods Replacement Kept getting an overbalance fault. Very heavy knocking sound during the rinse cycle. Written By: James ifixit CC BY-NC-SA www.ifixit.com
More informationPuffin Sport Assembly and User Information
Puffin Sport Assembly and User Information ScanSport, Inc. / Pakboats Post Office Box 700 May Street Enfield, New Hampshire 03748 USA Phone: (888) 863-9500 (toll free) From outside the US: +1 (603) 632-9500
More informationIce Axe-Boot belay Freedom of the Hills p. 350 Watch:
Carabiner-Ice Axe Belay Freedom of the Hills pp.358-359 Watch: http://bit.ly/carabinericeaxebelay Also called the stomper belay, the carabiner-ice axe belay provides better security than a boot-axe belay
More informationGrip-Lock Chock Repair Decision Instructions: Procedure and Examples (June 2013)
Grip-Lock Chock Repair Decision Instructions: Procedure and Examples (June 2013) A. Upperside Components All major plastic chock components, namely the Base, Platform, Flip-Face, Cover, Operating Lever
More informationInfant Swing ( )
Infant Swing (04-0017) 1. Insert the yellow T-bar into the hole at the front of the swing. If you need to disengage the T-bar you can squeeze the 2 tabs together under the seat while pulling the T-bar
More informationPuffin Sport and Saco
Puffin Sport and Saco Assembly and User Information Pakboats/ScanSport, Inc. Post Office Box 700 May Street Enfield, New Hampshire 03748 USA Phone: (888) 863-9500 (toll free) From outside the US: +1 (603)
More informationVERSA BIKE RACK INSTRUCTIONS
VERSA BIKE RACK INSTRUCTIONS Models #8, 8 Important This rack is designed for use with a or. receiver hitch. The rack is designed to hold a maximum of two bicycles. Do not use it for anything other than
More informationESCONDIDO FIRE DEPT TRAINING MANUAL Section ENGINE MODULE Page 1 of 14 IRIC/RIC Downed Firefighter Removal Revised
ENGINE MODULE Page 1 of 14 DOWNED FIREFIGHTER REMOVAL Moving the Downed Firefighter: Carries and Drags The process of rescuing a downed firefighter can become extensive and may involve multiple decisions
More informationE. Test, and if needed, adjust tips of antenna. 1. Mark will test antennas with meter at ground end of feedline bundle. Will take 10 minutes.
Project Steps Overview: A. Prepare: B. Raise up small antenna. C. Raise up large antenna. D. Connect to new bundle of 4-feedlines pulled up from ground. E. Test, and if needed, adjust tips of large antenna.
More informationSemi Freddo Snow kite [Ram Air]
User manual Semi Freddo Snow kite [Ram Air] This manual gives you detailed instructions on how to use your new Semi Freddo kite. We recommend you take your time to read the instructions. In case you have
More informationRefurbishing TR6 Window Slides. Chuck Hobbs 27 Feb 2017
Refurbishing TR6 Window Slides Chuck Hobbs 27 Feb 2017 Why Refurbish your Window Slides? Original slides are 40+ years old and are usually rusty, have no felt left on the runners and often the windows
More informationLazy Bag Installation Guide for Beneteau Yachts
INTERNATIONAL DESIGN AND TECHNICAL OFFICE Lazy Bag Installation Guide for Beneteau Yachts 8 August, 2001 Neil Pryde Sails Int. 354 Woodmont Road #18 Milford, CT 06460 Phone: 203-874-6984 Fax: 203-877-7014
More informationUsing Your Bike Friday : Folding Rear Rack
Using Your Bike Friday : Folding Rear Rack Green Gear Cycling, Inc. 3364 W. 11th Ave. Eugene, OR 97402 800-777-0258 USA & Canada +1-541-687-0487 Int l +1-541-687-0403 Fax www.bikefriday.com info@bikefriday.com
More informationTHOR 10 HAMMER CAGE INSTRUCTIONS
75 " 7m 78 4" m 6" 8.8m 45 ".70m 4.9deg 6 4" 6m 44 4".67m 75 " 7m 9 4" 0m 44".m 497 4".64m The 70, Thor Hammer Cage, consists of four heavy duty aluminum net poles. The unique pole structure reduces the
More informationKayak Trailer Project.doc
Kayak Trailer Project.doc Note: the red trailer shown in some of the illustrations is no longer available from Northern Tools. However, may be able to adapt similar trailer, but measurements may not be
More informationEQUIPMENT INFORMATION SYSTEM COMPONENTS OPERATOR INSTRUCTIONS
01 EQUIPMENT INFORMATION SYSTEM COMPONENTS 05 06 07 08 09 11 13 15 OPERATOR INSTRUCTIONS INSERTING BALLISTIC PROTECTION INTO PLATEBAGS 3-BAND SKELETAL CUMMERBUND ATTACHMENT (RELEASABLE) 3-BAND SKELETAL
More informationFirst Team Sports, Inc. Stellar Recreational Volleyball System
First Team Sports, Inc. Stellar Recreational Volleyball System BILL OF MATERIALS A 2 Volleyball Vertical Post K 1 ½ Centerlock Nut B 2 Height Labels L 2 Carabiner Clip C 3 Net Clamp M 1 ½ x 2 Hex Bolt
More informationAerial Litter Basket Set-Up
The following information is also based upon the manufactures recommendations of proper aerial stokes set-up procedures, and the teachings of aerial dynamics. Any deviation in setup procedures could possibly
More informationPakboats PakCanoe Assembly Instructions
Pakboats PakCanoe Assembly Instructions Note: Please read these assembly instructions carefully before assembling the canoe. a A. Assembling the canoe Note: Don't be afraid to get into the canoe while
More informationShip Wrecked! For background information on the Design Process, see pages 3-5.
Ship Wrecked! Outcome: 5-3-14: Use the design process to construct a prototype containing a system of two or more different simple machines that move in a controlled way to perform a specific function.
More information2. Note that the ropes from the rigging board are secured in the cam cleats of the jib fairleads.
VII 1. Place the hull, bow into wind, on its trailer, a soft surface, or a rigging board. We strongly recommend making a rigging board; it is simple and inexpensive and greatly simplifies rigging and working
More informationThe Rubber Band Car. Lesson Guide. The Challenge: To build a car that moves under the power of rubber bands! Topics: Forces, Energy, Simple Machines
The Rubber Band Car The Challenge: To build a car that moves under the power of rubber bands! Topics: Forces, Energy, Simple Machines Version 1 Materials: 2 compact discs (per group) Corrugated cardboard
More informationGTR FlexPLI Manual. FlexPLI Preparation before Car Testing
FlexPLI Manual FlexPLI Preparation before Car Testing 04.09.2013 A B current language Introduction Fitting Flesh Leg Preparation for Dynamic Inverse Test Fitting Flesh and Covers C Proposal Leg Preparation
More informationHolden Grip-Lock TM Chock Inspection and Repair Standards: Procedure and Examples (April 2016)
Holden Grip-Lock TM Chock Inspection and Repair Standards: Procedure and Examples (April 2016) This document is the property of IL, LLC, and should only be used in connection with the Holden Grip-Lock
More informationA white sail for Edmond Dantes
A white sail for Edmond Dantes Making a new junk sail, then rigging and test-sailing it in the summer of 2012 Part one The construction of the sail..ed in June 2011... Edmond Dantes is a 9.47m /4-ton Mikkel
More informationFALL RANGE PROTECTION
FALL PROTECTION RANGE PS53 544 FP19 506 Fall Protection is put in place to prevent the risks associated with falling from heights, reducing impact force, restricting obstacle/ground collision and restricting
More informationTWO KAYAK VERTICAL FOLD-DOWN CARRIER
S P X O TWO KAYAK VERTICAL FOLD-DOWN CARRIER TA R 2 50mm 40mm Stax Pro2 Kayak Carrier Red Load Straps Jawz Adapters Mounting Bolts Foam Blocks 9 Safety Strap 12 Tie-Downs Installation & Loading Instructions
More informationHobie Island Spinnaker Instructions
Hobie Island Spinnaker Instructions Please read through the instruction manual before using this product. 2 Installation Components 1. 2. 1. Swivel Cam Cleat 2. Mount for Cleat w/ Hardware 3. Padeye w/
More informationASSEMBLY GUIDE Deck buckles
TheY SSEMLY GUIDE Deck buckles Seam channels ackrest Cockpit handles Seat pad Coaming (cockpit rim) Deck strap (back) OW (front) Handle Handle Cockpit Stern fairing US PTENT NO. 8,316,788 ulkhead ulkhead
More informationFlat Fold Highchair INSTRUCTION MANUAL. Designed and manufactured to BS EN 14988: 2012 IMPORTANT:
Flat Fold Highchair INSTRUCTION MANUAL Designed and manufactured to BS EN 14988: 2012 IMPORTANT: Thank you for choosing our product. Please read and understand these instructions before using this flat
More informationPT 11 trouble-shooting and maintenance.
PT 11 trouble-shooting and maintenance. Does your rudder not stay down?...your back seat slip off?...your knobs tight and your leather pads loose? Maybe we can help. We have used our PT 11 s hard enough
More informationKnots, Hitches and Bends
Knots, Hitches and Bends It is hard to define clearly the terms knot, hitch and bend because their functions overlap. However, the terms may be generally defined as follows: Knots Hitches Bends Knots are
More informationBALL STOP INSTALLTION GUIDE
BALL STOP INSTALLTION GUIDE GROUND SLEEVE INSTALLATION: 1. Locate the exact location of the ground sleeve. NOTE: Maximum recommended pole spacing is 20 feet on center. 2. Excavate the pole footing; refer
More informationInstructions. Follow All Instructions Before Assembling Or Using This Product
Instructions Follow All Instructions Before Assembling Or Using This Product IMPORTANT DO NOT RETURN THIS PRODUCT TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE: (800) 492-9334 WARNING: Improper use
More informationASSEMBLY & FITTING GUIDE. Best Friend Mobility Dog Wheelchair Assembly Guide
1 Best Friend Mobility Dog Wheelchair Assembly Guide No matter what the reason, an injury or an illness, it is difficult when your pet becomes paralyzed or lose its ability to walk or move on its own.
More informationTHE GARRISON BINDER ...
Did you ever wonder why (to quote Andy Rooney) the Garrison binder is for many rodmakers the source of contentious problems while other rodmakers never seem to have problems. One of the primary reasons
More informationButler Tactical Parachute Systems, LLC
Butler Tactical Parachute Systems, LLC A division of Butler Parachute Systems Group, Inc. TT-600 TETHERED TANDEM BUNDLE DELIVERY SYSTEM PACKING MANUAL (REVISION A ) Page 1 of 62 INTRODUCTION This manual
More informationInstalling N-Strike Recon CS-6 Stage 1 and Stage 2 Performance Kits
Installing N-Strike Recon CS-6 Stage 1 and Stage 2 Performance Kits The Nerf N-Strike Recon CS-6 is a currently available blaster that is relatively easy to modify. The guys at Orange Mod Works have produced
More informationESOCCI RIGGING MANUAL
ESOCCI RIGGING MANUAL 1 Spray Covers Hull Rear Iako Forward Iako Ama ESOCCI RIGGING MANUAL 2 When training & racing in outrigger canoes, the canoe is your protector on the water and therefore it is imperative
More informationChapter 2 Rigging. Cutting Wire Rope. Anchoring Wire Rope to Drum. Winding Wire Rope Onto Drum
Chapter 2 Rigging Cutting Wire Rope The wire rope must be tightly seized on both sides of the point where the wire rope will be cut, as shown in Figure 2-1. Seize the wire rope with either seizing wire
More informationIMPRESS 3 Manual supplement Competition Speedbag
IMPRESS 3 Manual supplement Competition Speedbag Edition: 04/2014 Contents Introduction... 2 Fitting the speedbag... 2 Closing the speedbag... 2 Cockpit and Instrument panel... 2 Installing this second
More informationOPERATOR S MANUAL SPREADER. CSS, VNQ [For Combine Harvester AW82V] Original instructions
OPERATOR S MANUAL SPREADER CSS, VNQ [For Combine Harvester AW82V] en Original instructions Introduction Introduction Please read this operator s manual before using your spreader. We would first like to
More informationRamp B is steeper than Ramp A. Less force is needed to push boxes up Ramp A. However, you have to move the boxes over a greater distance.
What is a simple machine? Would you say this bicycle is a simple machine? It is certainly simpler than a car, but it does not fit the scientific definition of simple machine. A simple machine is a device
More informationLaying out the Grid Laying out an accurate grid pattern in the sand is very important in order to get the columns and rows straight and true.
Laying out the Grid Laying out an accurate grid pattern in the sand is very important in order to get the columns and rows straight and true. As of this writing, the plot is 72 feet wide by 156 feet deep
More informationDeluxe Gourd Racks I D E G A. Parts List. Shown above are parts for the two-level, Deluxe Gourd Rack (DGR 12V)with 12 arms for vertically hung gourds.
Deluxe Gourd Racks H F K I D E J C G A Shown above are parts for the two-level, Deluxe Gourd Rack (DGR V)with arms for vertically hung gourds. Parts List Code Quantity A B C D E F G H I J 6, or 4 6, or
More informationFIX ROAD & FIX STRAP cargo securing systems Operating Instruction Manual
FIX ROAD & FIX STRAP cargo securing systems Operating Instruction Manual NWE NETWORK ENGINEERING OY AB VAT: FI 09628099 1 Introduction Please ensure you read these instructions and understand them fully
More informationInstant Garage 20' x 12' 3" x 8' 3"
Instant Garage 20' x 12' 3" x 8' 3" Assembly Instructions Description Model # Instant Garage 20' x 12' 3" x 8' 3" - Grey CIG 1220 3503502 Recommended Tools OR THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED
More informationMALONER. Installation & Loading Instructions - Please Read Before Beginning. Step 1: Attaching Blocks to Kayak MPG152
Deluxe Kayak Kit SOFT RACK KAYAK CARRIER Kayak Blocks 9 Block Straps 15 Load Straps 12 Bow & Stern Lines Installation & Loading Instructions - Please Read Before Beginning 1 Step 1: Attaching Blocks to
More informationASSEMBLY GUIDE US PATENT NO. 8,316,788. Cockpit handles. Deck buckles. Seat pad. Seam channels. Coaming (cockpit rim) straps. (front) (back) Cockpit
SSEMLY GUIDE 2014 Deck buckles Seam channels ackrest ockpit handles Seat pad oaming (cockpit rim) Deck straps (back) ow (front) Handle Handle ockpit fairing ulkhead ulkhead ow fairing US PTENT NO. 8,316,788
More informationOPPI Rigging Guide 3/2008
OPPI Rigging Guide 3/2008 McLaughlin Boat Works optistuff.com Thanks for purchasing OPPI, the most durable and F-U-N sailboat available. Rigging your OPPI is easy and the following pictures make it a breeze
More informationInstallation Manual. Version 12-10
Installation Manual The products and parts shown herein are to be installed and used adjusted in accordance with these instructions. Any deviation by the buyer, installer, or user from these instructions
More informationButler Parachute Systems, Inc
Butler Parachute Systems, Inc A division of Butler Parachute Systems Group, Inc. TT-600 GEN 1 & 2 TETHERED TANDEM BUNDLE DELIVERY SYSTEM ASSEMBLY MANUAL 1 JUN 2010 INTRODUCTION This manual contains all
More informationASSEMBLY INSTRUCTIONS FOR 2B4004 GOAL
ASSEMBLY INSTRUCTIONS FOR 2B4004 GOAL 1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred, notify trucking company immediately. Lay out all parts. Remove
More informationLuna the African Flower Cat
Luna the African Flower Cat By: JO s Crocheteria You will need: Crochet hook 2mm and 3mm Yarn needle Cotton filling Yarn: Catania 26 x 36= 4 70 g black 20 g grey 220 g white 150 g brown Pattern In total
More informationSKED-EVAC Tripod Instructions
Skedco, Inc. Web Site: http://www.skedco.com E-mail: skedco@skedco.com P.O. Box 3390 Tualatin, Oregon 97062 USA Phone (503) 691-7909 FAX (503) 691-7973 SKED-EVAC Tripod Instructions FEATURES The Sked-Evac
More informationFar East Boat Optimist Rigging Instructions
Far East Boat Optimist Rigging Instructions These instructions are written specifically for Far East Boats Championship and Racing Optimist. Parts of the Optimist PAGE 1 Sprit Wind Indicator Sail Mast
More informationPro Climb Rigging Bollard USER MANUAL. Pro Climb Rigging Bollard
Pro Climb Rigging Bollard USER MANUAL Pro Climb Rigging Bollard www.proclimb.co.nz Protection Rubber Wear Sleeve Picture 1 Rigging Loop Introduction The Pro Climb Rigging Bollard (PCRB) is a friction device
More informationROPE RESCUE & RIGGING
ROPE RESCUE & RIGGING Field Guide Second Edition by Grant Prattley ROPE RESCUE & RIGGING Field Guide Second Edition 2016 Written and illustrated by Grant Prattley Copyright Over The Edge Rescue www.oterescue.com
More informationBasketball Instructions
Quality Family Games Basketball Instructions Model 752.69 Product Registration 752.69 08/14/14 Visit www.carrom.com to register your product to receive the latest product updates, special offers, and other
More informationASSEMBLY GUIDE Deck buckles
TheOST SSEMLY GUIE eck buckles Seam channels ackrest ockpit handles Seat pad oaming (cockpit rim) eck straps (back) OW (front) Handle Handle ockpit Stern fairing US PTENT NO. 8,316,788 ulkhead ulkhead
More informationPART NUMBER: E361SXA200 DESCRIPTION: KAYAK CARRIER
A KIT CONTENTS: : Plug 16x Long Carriage Bolt 4x Hex Key 4x Button Head Screw 4x Pad Strap BASE Over-Molded Wrench 1x SnapAround 4x 1/5 : Important Notes: Minimum crossbar spread of 24". If spread is less
More informationGel Drop Seal for FOSC 450 Fiber Optic Splice Enclosure Installation Instructions
Gel Drop Seal for FOSC 450 Fiber Optic Splice Enclosure Installation Instructions TECP-30-215 Issue 1 4/2013 INTRODUCTION The Gel Drop Seal device is for use with FOSC 450 B, B Short, C, and D size closures
More informationBAYST ASSEMBLY GUIDE Deck line
The YST SSEMLY GUIDE Deck line Deck web oaming (cockpit rim) ockpit handles Seat pad Seat back Zipper channel OW (front) (back) Handle Handle ockpit ow fairing US PTENT NO. 8,316,788 ulkhead ulkhead For
More informationTRAINING TIPS FOR STARTING HORSES
January, 2017 TRAINING TIPS FOR STARTING HORSES 1. CORRIDOR WITH BELL Give horses a long straight entry Encourage riders to push with seat and NOT too much leg Do not halt first time through just walk
More informationPectoral Machine. User manual E S S E N T I A L S T R E N G T H
E L E M E N T and the cable E S S E N T I A L S T R E N G T H User manual 1 and the cable and The identification plate of and manufacturer, affixed on the back panel of the weight stack, gives the following
More informationPRO BANDS TRAINING GUIDE
PRO BANDS TRAINING GUIDE Thank you for choosing SKLZ Pro Bands. We are dedicated to providing you with the best tools and instruction possible to help you unleash your athletic potential. If there is anything
More informationInstallation of 2 Tier In Line Greeting Card Rack
Installation of 2 Tier In Line Greeting Card Rack Material Sent to Store: Greeting Card Fixtures: 4ft Inline Tier Kit (1 per every 4ft based on planogram) 3ft endcap Tier Kit (will not receive if planogram
More informationMounting Instructions 2010 Wolfman Expedition Dry Saddlebags or Teton Saddlebags to another brand of Rectangular Side Rack.
Mounting Instructions OTHER 2010 Wolfman Expedition Dry Saddlebags or Teton Saddlebags to another brand of Rectangular Side Rack. Thank You for purchasing our new 2010 Wolfman Products Please Note: The
More information2016 Spring Fall Protection Construction Products
2016 Spring Fall Protection Construction Products Anchorage 3-Man Swiveling Roof Anchor 2103690 Reusable 3-man swiveling roof anchor for sloped wood structures with fasteners. Concrete D-ring Anchor 2104560
More informationAssembly, Installation, & Use Instructions
Assembly, Installation, & Use Instructions The information in this document is subject to change without notice. Copyright Springfree Trampoline Inc. 2005, 2015. All rights reserved. 706304 WARNING Read
More information! CAUTION! ! WARNING! General Information
Great Plains Mfg., Inc. Installation Instructions Used with: 2SF24, 24-Foot Two-Section Drill General Information Two-Section, Hydraulic Folding Marker 2SF30, 30-Foot Two-Section Drill 2SBM30, 30-Foot
More informationCornelius Keg Topping System for Barrels
Product# KEG405 MoreInstructions Cornelius Keg Topping System for Barrels Keg Like A Pro! Congratulations on your purchase and welcome to kegging! This guide is designed to teach you how to clean, sanitize,
More informationRIGGERS SAFETY SAFETY IS IN THE DETAILS FULL LINE CATALOG
RIGGERS SAFETY SAFETY IS IN THE DETAILS FULL LINE CATALOG Riggers Safety is a California-based manufacturer of Personal Fall Arrest Systems (PFAS) and Fall Prevention Products. Our automated manufacturing
More informationArmorer s Handgun Sight Tool
Armorer s Handgun Sight Tool Product #710905 Instructions #1054680 Rev. B 2 Top Knobs Height Adjustment Screw Adjustment Wheel Front Pusher Block Top Carriage Assembly 2 Front Pusher Block Screws Bottom
More informationLCI Party Deck OWNER'S MANUAL
LCI Party Deck OWNER'S MANUAL Introduction Lippert Components Party Decks are designed to help transform the ramp door of a coach into a comfortable, additional living space. The LCI Party Deck takes previously
More informationRudder Kit Assembly Instructions for Quest 13
Rudder Kit Assembly Instructions for Quest 13 Revised 4/2/2015 78501 Rudder System The Hobie Quest is designed for the addition of an optional rudder system. Rudder systems in boats like this allow you
More informationwww.myrower.com support@myrower.com ASSEMBLY Congratulations on purchasing the MyRower! Please see the following pages for instructions on assembling your MyRower. Bits bag contents: Rail Cross Bolt (90mm)
More informationcricket Premier Portable Cage Winch System Heavy Duty Parks Parks Cages Wooden Bays Stumps Netting Sundries cricket
cricket 21 Premier Portable Cage Winch System Heavy Duty Parks Parks Cages Wooden Bays Stumps Netting Sundries cricket setting the standard - leading the field Harrod UK continue to work with consultants
More informationREDMAN SUIT ASSEMBLING AND PACKING INSTRUCTIONS
ASSEMBLING AND PACKING INSTRUCTIONS RedMan Training Gear Train realistically and you train to survive. RedMan Training Gear empowers law enforcement, corrections, military and security professionals to
More informationNice. Nine. Need to. You
Nine Nice You Need to Okay, it s actually six knots, one sling, one lashing and one handy tip, but who can resist the alliteration? The knots are no big secret. You ll find them in many publications and
More informationHeight Safety Lifting Load Control
01 Safety Height Safety Lifting Load Control Management HARNESS RANGE Technical Data Sheet SpanSet Australia Ltd 13 Pullman Place Emu Plains NSW 2750 Australia Telephone +61 2 4735 3955 Fax +61 2 4735
More informationcomfort without compromising on performance and to fit your various needs on touring,
Congratulations on your purchase of Goal-26X. Goal-26X is made to enhance comfort without compromising on performance and to fit your various needs on touring, shopping and communicating. Let s have fun
More informationRIGGERS SAFETY SAFETY IS IN THE DETAILS FULL LINE CATALOG
RIGGERS SAFETY SAFETY IS IN THE DETAILS FULL LINE CATALOG Riggers Safety is a California-based manufacturer of Personal Fall Arrest Systems (PFAS) and Fall Prevention Products. Our automated manufacturing
More informationSkills Night 2005 Troop 80, B.S.A.
Skills Night 2005 Troop 80, B.S.A. Event Description Judge 1 st Rotation (7:10 8:00) 1a Pitch a Canadian Tent 2a Tripod with hanging bucket 3a Get over the electric wire 4a Challenge Station 5a Stretcher
More information