F a l l P r o t e c t i o n E x p e r t s. Subject: Use of Rope Grabs in Flat or Sloped Roof Applications
|
|
- Garey Snow
- 5 years ago
- Views:
Transcription
1 No. RG001, Rev. B Subject: Use of Rope Grabs in Flat or Sloped Roof Applications The use of DBI/SALA Rope Grabs (model , ) on flat or sloped roofs are acceptable as a means of fall protection under most conditions. The following guidelines should be observed and the special conditions noted. 1. The rope grabs must be used on a lifeline, which meets the requirements specified in the user instruction manual (i.e., size, construction, material, and strength). 2. The anchorage point shall be capable of supporting 5,000 pounds for fall arrest or 3,000 pounds for restraint applications. See user instruction manual for additional anchorage strength information. NOTE: Restraint anchorage may only be used where there is no possible vertical free fall. Restraint anchorage does not have sufficient strength for fall arrest. 3. The rope grab shall be connected directly to the body support (via locking carabiner) or with a short lanyard (not to exceed three feet in length). 4. Provisions shall me made (i.e., warning lines, monitors, guardrails, etc.) to prevent swing falls from otherwise unprotected roof edges or corners. 5. The lifeline must be protected from contact with sharp or abrasive edges and surfaces. 6. The rope grab locking operation must not be hindered by interference with the roof or objects on the roof surface. 7. Make certain enough clearance exists in the path of the fall to prevent striking an object. See user instructions for additional fall clearance information. 8. The rope grab and the lifeline system shall be positioned to prevent a free fall exceeding six feet (for fall arrest system). Restraint systems do not allow a free fall. 9. Training shall be conducted on the correct care and use, operating characteristics, application limits and consequences of improper use of the rope grab system. 10. All applicable guidelines in the user instruction manual shall be followed.
2 MISC007 Rev. B Subject: Certification / Inspection Frequency The following information describes the normal servicing, recertification and inspection requirements for the DBI/SALA products. Consult the user instruction manuals for complete details and information. Consult DBI/SALA for requirements relating to equipment used under special circumstances. SELF RETRACTING LIFELINES (SRL), CLIMB ASSIST SYSTEMS *DBI/SALA and ANSI require the product to be inspected at least annually by a Competent Person. Extreme conditions of use may require increasing inspection frequency. (In Canada, CSA requires SRL s to be serviced within two years of mfg. date, thereafter annually) *Before each use, DBI/SALA, OSHA and ANSI require SRL s to be inspected (by the user). *After an impact, the SRL must be removed from service (per DBI/SALA, OSHA and ANSI) and inspected. Servicing may be required. WINCHES *DBI/SALA recommends that Salalift I and II winches be serviced and recertified every year. Extreme working conditions may require increasing the frequency. *On a monthly basis, DBI/SALA recommends that a competent person other than the user formally inspect the winches. *Before each use, DBI/SALA requires winches to be inspected (by the user). *After an impact, the winch must be removed form service and inspected. Servicing may be required. RESCUE POSITIONING DEVICES (RPD S) *DBI/SALA recommends that RPD s be serviced and recertified every year. Extreme working conditions may require increasing the frequency. *On a monthly basis, DBI/SALA recommends that a competent person other than the user formally inspect the RPD. *Before each use, DBI/SALA requires the RPD to be inspected (by the user). RESCUMATIC CONTROLLED DESCENT DEVICE *DBI/SALA recommends that Rescumatics have maintenance check performed every 6 months by the user. *On a monthly basis, DBI/SALA recommends that the Rescumatic be formally inspected by a competent person other that the user. LAD SAF LADDER SAFETY SYSTEM *DBI/SALA requires the Lad Saf system (including sleeve) by inspected at least annually by a competent person. *Before each use, DBI/SALA and OSHA require the system to be inspected (by the user)
3 *After an impact, the entire system (including the sleeve) shall be inspected by a competent person. TRIPODS/DAVIT ARMS /SUPPORT STRUCTURES *DBI/SALA requires at least a monthly inspection by a competent person. *Before each use, DBI/SALA, OSHA and ANSI require an inspection (by the user). *After an impact, remove the product from service and inspect. Servicing may be required. LOAD ARRESTORS *DBI/SALA requires the load arrestors to be serviced and recertified every two years. Extreme working conditions may require increasing the servicing frequency. *Annually, a competent person should inspect the units. *After an impact, the load arrestor must be removed from service and returned to a repair center for service/recertification. HARNESSES/LANYARDS /POSITIONING EQUIPMENT /ROPE GRABS, ANCHORAGE CONNECTORS *DBI/SALA and ANSI require the product to be inspected at least annually by a competent person. *Before each use, DBI/SALA, OSHA and ANSI require an inspection (by the user). *After an impact, the product must be removed from service (per DBI/SALA, OSHA and ANSI). TEMPORARY HAORIZONTAL LIFELINE SYSTEM *DBI/SALA requires the system to be inspected annually by a qualified person. Extreme working conditions may require increasing the service frequency. *Before each use, and after installation, a qualified person shall inspect the system. *After an impact, the system must be removed from service (per DBI/SALA, OSHA and ANSI) or returned to the factory for inspection and/or repair.
4 Subject: Product Life Date: February 1998 No. MISC002, Rev. E The current DBI/SALA policy on the life of products is totally dependent on the condition of the item and not the age. A DBI/SALA product can be used as long as the inspection performed does not reveal any damage, wear, or other characteristics that will effect the product s performance. The inspection of the product shall be performed according to details outlined in the user instruction manual on the specific product as well as other applicable information provided by DBI/SALA. The frequency of inspections to determine the usability of the product shall be as follows: 1. Inspect before each use (by user). 2. Monthly (by competent person other than user) (for winches, RPD s, Rescumatics, tripods, davit arms) (recorded). 3. Annually (by competent person other than the user) (recorded). After a fall, the product shall be removed from service and destroyed (or used for educational purposes). After a fall, Self- Retracting Lifelines (SRL s) shall be inspected and serviced (if required, see user instructions) by factory authorized service center. Inspection and servicing frequency may need to be modified based on the amount of use and the conditions within the environment the product is used in. Current OSHA and ANSI regulations indicate the following regarding inspection of equipment: OSHA OSHA *Remove impacted systems and components. *Inspect systems prior to use. *Remove impacted systems and components. *Inspect systems prior to use. ANSI Z *Comply with manufacturer s instructions. *Inspection by user prior to use. *Inspect at least annually by competent person. All equipment found to be unusable shall be tagged as rejected and pulled out of service. Copies of user instructions and other available inspection information can be obtained from DBI/SALA. Activation Date Typically the date of manufacture on a product or the date of purchase is used to help determine when a product is due for inspection. The date of the products first use can also be used as an activation date. The activation date is defined as the time when a product is first put into actual service (initally or after service/repair).
5 If inspection timing is based on the activation date instead of the manufacture date, service date or purchase date, the activation date should be recorded in the user instruction manual in the inspection and maintenance log under the inspection date column (or record/document in some manner). Indicate that the entry is date of first use (or activation date). If the activation date is unknown, the product purchase date, service date, or manufacture date should be used to determine when product is due for inspection. Prior to placing a product into service that product shall be properly stored according to the user instruction manual. Learn more about clothing & work wear we have.
Subject: Certification / Inspection Frequency
Technical Bulletin MISC007 Rev. B Subject: Certification / Inspection Frequency The following information describes the normal servicing, recertification and inspection requirements for the DBI/SALA products.
More informationF a l l P r o t e c t i o n E x p e r t s. Subject: Product Life Date: February 1998
Technical Bulletin Subject: Product Life Date: February 1998 No. MISC002, Rev. E The current DBI/SALA policy on the life of products is totally dependent on the condition of the item and not the age. A
More informationF a l l P r o t e c t i o n E x p e r t s. Subject: Buckle Specifications and Operations
Technical Bulletin No. MISC008 Subject: Buckle Specifications and Operations DBI/SALA uses four types of buckles in full body harnesses, body belts and other fall protection equipment: parachute buckles,
More informationRegion: USA Language: EN Number : TB0031 Revision : B. Total Page: 3 Page n : 1 First Issue: 10/2014 Rev. Date: 10/08/2014
Subject Dropped Object Protection Region: USA Language: EN Number : TB0031 Revision : B Total Page: 3 Page n : 1 First Issue: 10/2014 Rev. Date: 10/08/2014 Some users of fall protection equipment require
More information1.3 LIMITATIONS: The following application limitations must be recognized and considered before using this product:
3965 Pepin Avenue Red Wing, MN 55066-1837 Toll Free: (800) 328-6146 Phone: (651) 388-8282 Fax: (651) 388-5065 www.protecta.com User Instruction Manual AJ720A Concrete Anchor This manual is intended to
More information1.2 LIMITATIONS: Consider the following application limitations before using this equipment:
User Instruction Manual Standing Seam Roof Anchor This manual is intended to meet the Manufacturer s Instructions, and should be used as part of an employee training program as required by OSHA. Figure
More informationFall / Impact Indicators in Full Body Harnesses. Region: USA Language: EN Number : TB0027 Revision : A
Technical Bulletin Subject Fall / Impact Indicators in Full Body Harnesses Region: USA Language: EN Number : TB0027 Revision : A Total Page: 1 Page n : 1 First Issue: 02/2014 Rev. Date: 2/28/2014 Harnesses
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 7100 Series Lanyards Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046 Deer Park, TX 77536 Phone :
More informationFall Protection ABC s
Fall Protection ABC s Chris Caron American Safety & Supply, Inc. Fall Protection ABC Itinerary Review types of fall arrest systems Review and discuss ladder safety Discuss the various components of fall
More informationWARNING! DO NOT THROW AWAY THESE INSTRUCTIONS! READ AND UNDERSTAND BEFORE USING EQUIPMENT!
Guardian Fall Protection Kent, WA 800-466-6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment shall
More informationFall Protection. ANSI-What is it, Why is it important? Craig Firl. March 5 th, Company Private
Fall Protection ANSI-What is it, Why is it important? New ANSI Standards Craig Firl March 5 th, 2013 ANSI Fall Protection Standards What is ANSI? American National Standards Institute Voluntary Consensus
More informationFigure 1 - Parts Identification. Copyright 2002, DB Industries, Inc.
User Instruction Manual Zorbit Energy Absorber Kits for Horizontal Lifeline Systems This manual is provided as the Maunfacturer s Instructions, and should be used as part of an employee training program
More informationINSTRUCTIONS FOR USE
Rebar Chain Assembly INSTRUCTIONS FOR USE 7260XX Rebar Chain Assembly Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046
More informationUser Instruction Manual Fixed Beam Anchor
User Instruction Manual Fixed Beam Anchor This manual is intended to meet the Manufacturer s Instructions as required by ANSI Z359.1 and ANSI A10.14, and should be used as part of an employee training
More informationInstructions for the following series products:
Instructions for the following series products: U-Bolt Roof Anchors (See back page for specific model numbers.) User Instruction Manual U-bolt Roof Anchor This manual is intended to be used as part of
More information??????? is committed to providing a safe work environment for its employees and preventing occupational injuries due to falls.
Intent??????? is committed to providing a safe work environment for its employees and preventing occupational injuries due to falls. Fall Protection is an integral part of our commitment to a safe work
More informationUser Instruction Manual Tripod Anchorage Connectors
User Instruction Manual Tripod Anchorage Connectors This manual is intended to meet the Manufacturer's Instructions as required by ANSI Z359.1 and ANSI A10.14, and should be used as part of an employee
More informationWARNING! DO NOT THROW AWAY THESE INSTRUCTIONS! READ AND UNDERSTAND BEFORE USING EQUIPMENT!
Guardian Fall Protection Kent, WA 800-466-6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment shall
More informationUser Instruction Manual Roof Anchor and / Sayfline Horizontal Lifeline System
Instructions for the following series products: Roof Anchor (See back page for specific model numbers.) User Instruction Manual 2103673 Roof Anchor and 76002001/7600202 Sayfline Horizontal Lifeline System
More informationUser Instruction Manual Fixed Beam Anchor
Instructions for the following series products: FIXED BEAM ANCHOR Model Numbers: The Ultimate in Fall Protection 2108406 2108407 2108408 2108409 2108410 2108411 User Instruction Manual Fixed Beam Anchor
More informationfall arrest. Contact your distributor or Guardian about policies regarding replacement of Guardian components involved in a fall.
Guardian Fall Protection Kent, WA 800-466-6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment shall
More informationIMPORTANT: Record the product identification information from the ID label in the inspection and maintenance log in section 9.0 of this manual.
Instructions for the following series products: Vacuum Anchor HLL System (See back page for specific model numbers.) User Instruction Manual Vacuum Anchor Horizontal Lifeline System This manual is intended
More informationSECTION FACILITY FALL PROTECTION PART I - GENERAL
SECTION 11 24 29 - FACILITY FALL PROTECTION PART I - GENERAL 1.1 The Illinois Department of Labor (IDOL) regulates fall protection for general industry and construction in the public sector under the Illinois
More informationGEMTOR. ... when your life is on the line OWNER'S MANUAL. FLW Series Self-Retracting Lanyard/Fall Limiter
GEMTOR TM... when your life is on the line OWNER'S MANUAL FLW Series Self-Retracting Lanyard/Fall Limiter Installation, Operating, Inspection and Maintenance Instructions Warning You must read and fully
More informationFigure 1 - Cable Grip Horizontal Lifeline Termination ZORBIT ENERGY ABSORBER RELEASE TAB
Instructions for the following series products: Cable Grip (See back pages for specific model numbers.) User Instruction Manual Cable Grip Kit for Horizontal Lifeline Systems This manual is provided as
More informationSelf Retracting Device User Instruction Manual
6.3 INSPECTION AND MAINTENANCE LOG CONTINUED: Model: Serial #: Date of Mfg: Class: SRL SRL-R SRL-LE INSPECTION DATE INSPECTION ITEMS NOTED CORRECTIVE ACTION MAINTENANCE PERFORMED Web Devices Fall Arrest
More informationROOF ANCHOR / D-RING ANCHOR PLATE
RIGGERS SAFETY Riggers Safety LLC. 267 Winfield Cr. Corona, CA 92880. 951 371 8586. www.riggerssafety.com Use and Safety Manual ROOF ANCHOR / D-RING ANCHOR PLATE Table of Contents WARNINGS 3 Definitions
More informationARKANSAS TECH UNIVERSITY FACILITIES MANAGMENT HEALTH AND SAFETY MANUAL
FALL PROTECTION (PERSONAL FALL ARREST SYSTEMS) 15.0 The purpose of this policy is to specify procedures and training for the safety of the employees in the Facilities Management Group while working on
More informationPatrick Harel Ph
Patrick Harel Ph- 920-418-2714 pharel@capitalsafety.com The Worldwide Experts in Fall Protection Standards Occupational Safety and Health Administration (OSHA) 29 CFR 1910 and 1926 Governing Body Sets
More informationFigure 1 - Parts Identification
Instructions for the following series products: Zorbit Energy Absorber Kits (See back page for specific model numbers.) User Instruction Manual Zorbit Energy Absorber Kits for Horizontal Lifeline Systems
More informationUser Instructions 1790 Rail Anchor
User Instructions 1790 Rail Anchor This document is intended to meet the Manufacturer s Instruction requirements as stated by ANSI Z359.1, and should be used as part of an employee training program as
More informationRescue Ladder Model: CTB LDR-RSC 18ft (5.48m)
Rescue Ladder Model: CTB LDR-RSC 18ft (5.48m) IMPORTANT!!! ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS SHOULD
More informationProduct Name: Hold Me Rope Anchor
Product Name: Hold Me Rope Anchor Part #: 01300 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 88004X Series D-Ring Extender 5000 lb Rated Connector Complies with ANSI Z359.1-1998, ANSI 10.14 and OSHA 1926 regulations and requirements. Reliance Industries P.O. Box 2046 Deer
More informationRescue Ladder Basic Kit Model: LDR-BAS-CTS 18ft (5.48m)
Rescue Ladder Basic Kit Model: LDR-BAS-CTS 18ft (5.48m) Patent # US 9,677,333 WARNING: ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS
More information11.4 FALL-ARREST SYSTEM AND EQUIPMENT CHECKLIST (Must answer yes to all applicable questions)
11.4 FALL-ARREST SYSTEM AND EQUIPMENT CHECKLIST (Must answer yes to all applicable questions) This checklist shall be completed either by the Competent Person or a person trained and designated by the
More informationUser Instruction Manual. Fixed Beam Anchor
Instructions for the following series products: Fixed Beam Anchor (See back page for specific model numbers.) User Instruction Manual Fixed Beam Anchor This manual is intended to meet the Manufacturer
More informationKnow Your ABCs FALL PROTECTION GUIDE
Know Your ABCs FALL PROTECTION GUIDE PEAKWORKS ABCs of Fall Arrest KNOW YOUR ABCs Fall arrest systems are the collection of equipment components that are configured to arrest a fall. There are several
More informationUser Instruction Manual For Davit Rescue System
Instructions for the following series products: Rescue Davit System Model numbers 8004000 and 8302500 User Instruction Manual For Davit Rescue System This manual should be used as part of an employee training
More informationPart #: 42000; 42001; 42002; 42003; 42004; 42005; 42006; 42008
Product Name: Velocity SRL Part #: 42000; 42001; 42002; 42003; 42004; 42005; 42006; 42008 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment!
More informationUSER INSTRUCTION MANUAL CONCRETE BOLT ANCHORAGE CONNECTOR
Instructions for the following series products: Concrete Bolt Connector Models: 2100041, 2100066, 2104560, 2104561, 2104562 USER INSTRUCTION MANUAL CONCRETE BOLT ANCHORAGE CONNECTOR This manual is intended
More informationRescue Ladder Model: KT ft (5.48m)
Rescue Ladder Model: KT36164 18ft (5.48m) IMPORTANT!!! ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS SHOULD BE
More informationUser Instructions 1789 Parapet Wall Anchor
User Instructions 1789 Parapet Wall Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee training program as required
More informationRescue Ladder Basic Kit Model: FS-EX243 18ft (5.48m)
Rescue Ladder Basic Kit Model: FS-EX243 18ft (5.48m) IMPORTANT!!! ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS
More informationIMPORTANT: If you have questions on the use, care, application, or suitability of this equipment contact DBI/SALA.
Model Numbers: (See back cover for model numbers) User Instruction Manual Body Belts for Personal Restraint Applications This manual ishould be used as part of an employee training program as required
More informationOPERATION AND INSTRUCTION MANUAL ROLLER SLING Model: IN106.3FT & IN106.2FT
OPERATION AND INSTRUCTION MANUAL ROLLER SLING Model: IN106.3FT & IN106.2FT IMPORTANT!!! ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS
More informationThe purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field.
Purpose The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field. Fall Protection and Prevention JELD-WEN Field Employees
More informationProduct Name: Concrete Anchor Strap
Product Name: Concrete Anchor Strap Part #: 10705; 10710; 10715 ; 10717; 10720 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Table
More informationImportant: If you have questions on the use, care, or suitability of this equipment for your application contact Capital Safety.
User Instruction Manual for: Saflok Toggle Anchor (Model Number: 2100101) User Instruction Manual Saflok Toggle Anchor This manual is intended to meet the Manufacturer s Instructions as required by ANSI
More informationOperating instructions. Skyline Beam Clamp
Operating instructions for Skyline Beam Clamp Model # 3093 Reliance Industries, LLC PO Box 140008 Denver, CO 80214 Ph. (800) 488-5751 Ph. (303) 424-8650 Fax (303) 424-8670 User Instructions 3093 Skyline
More informationOPERATION AND INSTRUCTION MANUAL Flat Roof Anchor Model: FRA250L-10X-CTS
OPERATION AND INSTRUCTION MANUAL Flat Roof Anchor Model: FRA250L-10X-CTS (Patent Pending) WARNING: ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT
More informationSaflok Concrete Wedge Anchor
User Instruction Manual for: Saflok Concrete Wedge Anchor (Model Numbers: 2100085, 2100085C) User Instruction Manual Saflok Concrete Wedge Anchor This manual is intended to meet the Manufacturer s Instructions
More informationrooftop anchor Standing Seam Metal Roofs
The Ultimate in Fall Protection INSTRUCTION MANUAL ANSI Z359.1 OSHA This manual is intended to meet the Manufacturer s Instructions as required by ANSI Z359.1 and should be used as part of an employee
More informationProduct Name: 2-Way Standing Seam Roof Clamp
Product Name: 2-Way Standing Seam Roof Clamp Part #: 10600 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable
More informationProduct Name: Rope Grab
Product Name: Rope Grab Part #: 01500; 01503; 01505; 01506; 01507; 01511 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction
More informationProduct Name: Angel Anchor
Product Name: Angel Anchor Part #: 00260 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards
More informationRollGliss Rescue Emergency Descent Device. This manual is intended to be used as part of an employee training program as required by OSHA.
User Instruction Manual for: RollGliss Rescue Emergency Descent Device with Auto-Retract (Model Numbers: See Figure 1) User Instruction Manual RollGliss Rescue Emergency Descent Device with auto-retract
More informationProduct Name: Edge Series Web SRL
Product Name: Edge Series Web SRL Part #: 10900; 10901, 10909, 20900 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction
More informationFALL PROTECTION (SAF-SPI-06)
1. PURPOSE To describe the Ontario Operations standard methods for preventing serious injury resulting from fall from heights and to provide a Standard for Fall Protection to safeguard employees who work
More informationDepartment of Facilities Management. Occupational Health and Safety. Fall Protection Program
Department of Facilities Management Occupational Health and Safety Fall Protection Program October 2016 1 1.0 INTRODUCTION This program has been developed to provide guidance to those managers and supervisors
More informationLAD-SAF STATIC WIRE ROPE GRAB
A Capital Safety Company INSTRUCTION MANUAL LAD-SAF STATIC WIRE ROPE GRAB FOR 3/8 INCH WIRE CABLE Model Number: 5000338 Figure 1 Static Wire Rope Grab Model Description Cable Requirements 5000338 Wire
More informationProduct Name: Bull Ring Anchor
Product Name: Bull Ring Anchor Part #: 00484 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards
More informationProduct Name: Non-Shock Lanyard
Product Name: Non-Shock Lanyard Part #: 01121, 01122; 01280, 01250, 01255, 01260, 01265, 01251, 01261, 01265, 01270, 01271 Instruction Manual Do not throw away these instructions! Read and understand these
More informationFigure 1 - Snap Hooks and Carabiners PART NUMBER MANUFACTURER S ID YEAR OF MANUFACTURE PART NUMBER MANUFACTURER S ID YEAR OF MANUFACTURE
Instructions for the following series products: SNAP HOOKS AND CARABINERS (See back page for specific model numbers.) User Instruction Manual Snap Hooks and Carabiners This manual is intended to meet the
More informationProduct Name: Edge Angel SRL
Product Name: Edge Angel SRL Part #: 10920; 10922; 10925 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable
More informationTable of Contents Beam Trolley
I178 Rev H / 34-9720066 31 January 2012 Table of Contents 3.1 9065 Beam Trolley 2 Thank You WARNING All persons using this equipment must read, understand and follow all instructions. Failure to do so
More informationFigure Figure 2 - Applications
User Instruction Manual 5000335 Rope Grab This manual is intended to meet the Manufacturer's Instructions as required by OSHA and should be used as part of an employee training program as required by OSHA
More informationFALL PROTECTION GUIDELINE
FALL PROTECTION GUIDELINE July 2001 Table of Contents INTRODUCTION...3 CONTROL MEASURES...4 SURFACE PROTECTION...4 FIXED BARRIERS...5 EXAMPLES OF GUARDRAIL...6 WARNING BARRIERS...7 HANDRAILS...8 SURFACE
More informationDBI SALA Confined Space Rescue Davit System
Instructions for the following series products: Rescue Davit System (See back page for specific model numbers.) User Instruction Manual For Davit Rescue System This manual should be used as part of an
More informationSafe Work Practices (SWP) SWP (6) FALL PROTECTION PROGRAM
SWP (6) FALL PROTECTION PROGRAM The following information on Fall Protection has been based around the BC OHS Regulations, standards, policies and guidelines. Prior to starting work outside of BC, the
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 68XXXX Series Anchorage Slings Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046 Deer Park, TX 77536
More informationOperations and Instruction Manual Might Swivel Model # Concrete and Steel Anchorage Connector ANSI Z ,000 lbs / 44kn
Operations and Instruction Manual Might Swivel Model # 00238 Concrete and Steel Anchorage Connector ANSI Z359.1 10,000 lbs / 44kn Description: Zinc plated forged heat treated steel, Special design gives
More informationSafeWaze Fall Protection Technical Data Sheet. General Information. Inspection and Examination
SideWalk 30,60, 100 Rope Horizontal Lifeline Systems General Information PD 4-30-08 The HORIZONTAL SAFETY LINES have been tested to the standards described in ANSI Z359.1-1992, CSA Z259.13-04 and certified
More informationFALL PROTECTION
115500 FALL PROTECTION PART 1 GENERAL 1.01 General A. Cornell University seeks to prevent exposures to fall hazards whenever possible and protect personnel that may be exposed to fall hazards. Therefore,
More informationUSER INSTRUCTIONS LARGE HOOK & STRAP ANCHORAGE CONNECTOR ! WARNING
ROSE MODEL NUMBER USER INSTRUCTIONS LARGE HOOK & STRAP ANCHORAGE CONNECTOR! WARNING National standards and state, provincial and federal laws require the user to be trained before using this product. Use
More informationProduct Name: Standing Seam Roof Clamp
Product Name: Standing Seam Roof Clamp Part #: 00250 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety
More informationProduct Name: Internal Shock Lanyard
Product Name: Internal Shock Lanyard Part #: 11200; 11201; 11202; 11203; 21215; 01295; 01296; 01297; 01298; 11211; 11212; 11213; 11260; 11261 Instruction Manual Do not throw away these instructions! Read
More informationGUARDIAN CB ANCHORS. Model Numbers: SS
GUARDIAN CB ANCHORS Model Numbers: 00600 00601 00600-SS 00610 00645 00651 00652 00653 00656 00657 00680 00690 10681 10683 USER S MANUAL KEEP THIS FOR YOUR RECORDS AND TRAINING PURPOSES! READ AND UNDERSTAND
More informationNew Mexico Institute of Mining & Technology. Fall Protection Program
New Mexico Institute of Mining & Technology Fall Protection Program REGULATORY STANDARDS: OSHA - 29 CFR 1910.66 29 CFR 1910.128, 129, 130, 131, (Proposed) 29 CFR 1926.104 29 CFR 1926.500 BASIS: Approximately
More informationNew ANSI Fall Protection Standards
ANSI Z359.7 and ANSI Z359.14 Rick Maurice Craig Firl June 17, 2016 ANSI Z359.14 Self Retracting Devices Effective August 20, 2012 SUMMARY New terms SRD, SRL-R, SRL-LE New classifications Class A, Class
More informationFall Protection / Open Holes & Guardrail
Fall Protection / Open Holes & Guardrail 1. Leading Edges Policy Statement It is GW Communications policy that any worker exposed to a fall 6 or greater, shall be protected from coming into contact with
More informationFALL PROTECTION WORK PLAN (Alstom Power Installation Canada)
FALL PROTECTION WORK PLAN (Alstom Power Installation Canada) Location: Unit: Foreman: Task: Supervisors Ensure: Workers must review and sign this fall protection work plan prior to starting work in an
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 714XXX Series Lanyard Extender Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046 Deer Park, TX 77536
More informationUser Manual 1792 Standing Seam Metal Roof Retractable Swivel Anchor
1 User Manual 1792 Standing Seam Metal Roof Retractable Swivel Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee
More informationInstructions for the following series products:
Instructions for the following series products: EZ-Line Horizontal Lifeline System Model Number 7605060 User Instruction Manual EZ-Line Horizontal Lifeline System This manual is intended to meet the Manufacturer
More informationArco Pod. Guardian Fall Protection Kent WA WARNING!
Guardian Fall Protection Kent WA 98032 800.466.6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment
More informationUSER S INSTRUCTION MANUAL FOR THE INSTALLATION, OPERATION & MAINTENANCE OF THE GUARDIAN TEMPORARY HORIZONTAL LIFELINE SYSTEM
USER S INSTRUCTION MANUAL FOR THE INSTALLATION, OPERATION & MAINTENANCE OF THE GUARDIAN 04630 TEMPORARY HORIZONTAL LIFELINE SYSTEM 1 WARNING This is a design compatible component for a comprehensive Guardian
More informationAre You OSHA Compliant? Browse Our Products Specifically For Compliance With The Updated Walking-Working Surfaces and Fall Protection Standard.
Are You OSHA Compliant? Browse Our Products Specifically For Compliance With The Updated Walking-Working Surfaces and Fall Protection Standard. OSHA s Walking-Working Surfaces and Fall Protection Standard
More informationOPERATION AND INSTRUCTION MANUAL
OPERATION AND INSTRUCTION MANUAL Swivel Anchor Model: SWS100N-316-CTS Patent US # 8,424,638 WARNING: ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT
More informationAmerican National Standards Institute, ANSI Z359 Fall Protection Code Update
NAVFAC SOUTHEAST American National Standards Institute, ANSI Z359 Fall Protection Code Update John Davis, SSM Prepared by: Basil Tominna, P.E. September 2010 29 June 2012 Introduction ANSI approved several
More informationWrapBax 2 Lanyards With Integral Energy Absorbers
Instructions for the following series products: WrapBax 2 Lanyards (See back page for specific model numbers.) User Instruction Manual WrapBax 2 Lanyards With Integral Energy Absorbers This manual is intended
More informationFall Protection STANDARD PROCEDURE INSTRUCTION. Fall Protection. Title SPI. Department. Supersedes SPI Dated. Jan 19, 2016.
STANDARD PROCEDURE INSTRUCTION Title Fall Protection Department Safety, Health and Environment Supersedes SPI Dated March 27, 2014 SPI 34-21 Effective Date Jan 19, 2016 Fall Protection SPI 34-21 Page 1
More informationProduct Name: 2-Way Standing Seam Roof Clamp. Instruction Manual. Part #: 10600
Product Name: 2-Way Standing Seam Roof Clamp Part #: 10600 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Table of Contents Introduction
More informationFigure Figure 2 - Applications
User Instruction Manual 5000335 Rope Grab This manual is intended to meet the Manufacturer's Instructions as required by ANSI Z359.1, and should be used as part of an employee training program as required
More informationFall Hazards, Anchor Points and Fall Clearances OSH-2 August 7, 0900
Fall Hazards, Anchor Points and Fall Clearances OSH-2 August 7, 2017 @ 0900 Phil Fincher, CIH, CSP Overview ANSI & OSHA Fall Protection Standards Definitions, Roles, & Responsibilities of Authorized, Competent,
More informationFall Protection Checklist. Guardrail System
Fall Protection Checklist Location/Department: Date of Inspection: Inspectors: Corrective Actions: Work order/memos were issued: Yes No Date issued: In accordance with the MIOSHA and OSHA standards the
More informationFall Protection PPT-SM-FALLPROT V.A.0.0
Fall Protection 1 Introduction to Fall Protection Falls account for 13% of fatal injuries 11% of these fatal falls were to a lower level Workers may be required to perform tasks at great heights which
More informationProduct Name: Beamer Instruction Manual. Part #: 00110
Product Name: Beamer 12-1 Part #: 00110 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Guardian Fall Protection 6305 S. 231st St.,
More informationRoof Anchor and Sayfline Horizontal Lifeline System
Instructions for the following series products: Model Numbers: 2103673 User Instruction Manual 2103673 and 7600511 Sayfline Horizontal Lifeline System This manual is intended to meet the Manufacturer s
More informationProduct Name: Snappy Anchor
Product Name: Snappy Anchor Part #: 00710; 00711; 00715-TV Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable
More information