Pre-Climbing Inspections
|
|
- Felicity Malone
- 6 years ago
- Views:
Transcription
1 Trainer s Instructions Session 45 Training Objective At the end of this session, the worker should understand the some of the risks associated with tree climbing and how to reduce the risk with a pre-climb inspection. Job Steps Affected by Today s Topic Tree climbing Potential Hazards/Risks Electricity Decay Hangers Root rot Stinging insects/animals Example of Preventable Incidents In 1990, a 27-year-old tree trimmer was working as part of a four-person crew to remove dead trees from a private home in a semi-rural area. The crew had been on the site for two days and had removed four large trees. They were working on the fifth tree and had cut off all of the tree limbs. Even though each tree was checked for rot by tapping on the trunk, the crew was unaware of the decay in the upper trunk. Using a saddle, buck strap, and climbing spurs, the trimmer climbed the tree to cut it away in sections. When the trimmer climbed into the section that was decayed, the spar snapped, taking the trimmer with it. The tree pinned the trimmer to the ground. Death was instantaneous. Some trees fall over because of root decay or cut roots. Trees have also broken off above the ground because of cankers, decay or weak limb attachments. ANSI requirements and suggested safe work procedures An inspection shall be made by a qualified arborist to determine whether an electrical hazard exists before climbing, otherwise entering, or performing work in or on a tree A visual hazard assessment, including a root collar inspection, shall be performed prior to climbing, entering, or performing any work in a tree Arborists shall inspect climbing lines, worklines, lanyards, and other climbing equipment for damage, cuts, abrasion, and/or deterioration before each use and shall remove them from service if signs of excessive wear or damage are found. PPE advised for this job function: Continued on next page TAILGATE SAFETY 287
2 Trainer s Instructions Session Arborists performing rigging operations shall inspect trees for their integrity to determine whether the trees have any visible defect that could affect the operation. If it is determined that the tree poses a risk of failure due to the forces and strains that will be created by the design of the rigging operation, an alternate plan shall be used Rigging points shall be assessed for their structural integrity by a qualified arborist. The rigging plan and the tree shall be considered relative to the forces being applied to any part of the tree, including branch attachments and anchoring roots, before a rigging point is chosen and established Arborists performing rigging operations shall be educated to understand and trained to estimate the potential forces at any point in the rigging system being used. The system components shall comply with working-load limits relative to the operation and the maximum potential forces Careful consideration shall be given to the potential for additional forces resulting from the speciἀc inἀuences of rigging design, rope angles, and the number of lines and/or line parts that will act on any rigging or anchor point Before beginning any tree removal operation, the chain saw operator, equipment operator, and/or crew leader shall carefully consider relevant factors pertaining to the tree and site and shall take appropriate actions to ensure a safe removal operation. Factors to include may be, but are not limited to, tree decay, tree lean, and wind (see Annex C.3, Manual Tree Felling Procedure, for a more inclusive list). What else can you do to prevent injuries 288 TAILGATE SAFETY
3 Handout Session 45 Job Steps Affected by Today s Topic Tree climbing Potential Hazards/Risks Electricity Decay Hangers Root rot Stinging insects/animals Action Steps u Obvious tree-related hazards should be noted on the work order and reviewed by the crew before starting a job. u Before starting any tree work, the property should be inspected by the crew to find the electricity and any other potential hazards. u Learn how to inspect a tree for potential hazards before you start to climb it; if you do not know how, ask an experienced climber to show you. Inspect for root hazards, root rot, cut roots, trunk hazards, cankers, weak crotches, stinging insects, dead branches, hangers and utility wires. Inspection of Climbing Gear Customize and use this sample checklist to help inspect your climbing gear and equipment for wear and/or damage daily before use. Check your personal protection equipment for: helmet, including strap and webbing; safety glasses; hearing protection; other PPE that should be checked before you climb. Next check your climbing line for: glossy or glazed areas, indicating heat damage; inconsistent diameter, indicating internal damage; discoloration, indicating chemical contamination; areas of stiffness, fraying or puffs; integrity of spliced ends; other potential problems with your line. Continued on back PPE advised for this job function: TAILGATE SAFETY 289
4 Handout Session 45 Check your saddle for: abraded webbing; worn stitching; loose grommets; other potential problems with your saddle. Check your lanyard (flipline). First, perform an inspection of the rope, looking for the same defects you checked for in your climbing line. Second, check the hardware for: proper function of snap, carabiner or screw links; inspect the length adjuster for proper operation and attachment; other potential problems with your lanyard system. Check the rest of your climbing hardware for wear and proper operation: carabiners, rope snaps, screw links and ascenders for excessive wear, loose parts in spring-loaded mechanisms, and/or proper locking function; Prusik loops; split tails, especially for worn, burned, and/or glazed areas; integrity of splices; false crotches and redirect slings; ladders; check for other potential problems with your climbing hardware. If you find excessive wear or damage, the equipment must be: 1.) Destroyed immediately; or, 2.) Retired from climbing and put to a different, non-critical use; or, 3.) Marked for repair and removed from service until the repair is complete. 290 TAILGATE SAFETY
5 Quiz Session 45 Complete the following: Name: Date: / / Signature: Multiple Choice Instructions: Select the one statement that best answers each question. 1. Before climbing a tree, you should make. a) a visual trunk inspection b) a visual inspection of the entire tree c) a visual root inspection d) a visual crown inspection 2. During climbing operations, tree limbs should be before weight is applied to them. a) removed b) pruned c) inspected d) shaken 4. Hands and feet should be placed on separate part(s) of the tree while climbing. a) 1 b) 2 c) 3 d) 4 True or False Instructions: Indicate if the statement is true (a) or false (b). 5. The worker should climb on the side of the tree that is farthest from the utility lines. a) True b) False 3. Dead branches should be removed if possible. a) soon b) on the way up c) on the way down d) any time TAILGATE SAFETY 291
Chapter 16 Workbook Questions
1. List four defects that might be found during rope inspection that would require a rope to be retired. a. b. c. d. cuts, excessive fraying, abrasions puffs, pulled or herniated fibers changes in diameter
More informationFall Protection STANDARD PROCEDURE INSTRUCTION. Fall Protection. Title SPI. Department. Supersedes SPI Dated. Jan 19, 2016.
STANDARD PROCEDURE INSTRUCTION Title Fall Protection Department Safety, Health and Environment Supersedes SPI Dated March 27, 2014 SPI 34-21 Effective Date Jan 19, 2016 Fall Protection SPI 34-21 Page 1
More informationPreface Introduction Tools of the Trade: Gearing Up The P.R.E.P. Tree Climbing System P Pre-Climb Inspection
CONTENTS Preface... 6 Introduction... 7 Tools of the Trade: Gearing Up... 8 The P.R.E.P. Tree Climbing System... 10 P Pre-Climb Inspection... 11 1. Inspect Equipment... 12 Tools of the Trade: Buckets,
More informationYou may order this publication from WCB Publications and Videos, Please quote ordering number BK60.
The following material is the property of the Workers Compensation Board of British Columbia and may not be reproduced by those outside of B.C. For those within British Columbia, this material may only
More informationStep By Step How to Establish, Manage and Implement a Fall Protection Program
Step By Step How to Establish, Manage and Implement a Fall Protection Program The following is a step by step guideline for establishing, managing and implementing a fall protection program arranged in
More informationFall Protection Checklist. Guardrail System
Fall Protection Checklist Location/Department: Date of Inspection: Inspectors: Corrective Actions: Work order/memos were issued: Yes No Date issued: In accordance with the MIOSHA and OSHA standards the
More informationPN BuckCat Series Saddles Instructions/Warnings
PN 16905 BuckCat Series Saddles Instructions/Warnings The BuckCat is a light weight saddle developed for the professional arborist. It is fully adjustable at the sides, waist and legs to provide ease of
More informationFall Protection PPE Inspection
Fall Protection PPE Inspection Fall Protection Equipment All Personal Protective Equipment (PPE) shall be inspected when issued, prior to each use and on a regular basis If found defective it should be
More informationSADDLES FOR ARBORISTS USE INSTRUCTIONS / WARNINGS
SADDLES FOR ARBORISTS USE INSTRUCTIONS / WARNINGS All Arborist Saddles manufactured by Buckingham Mfg. Co. are made from the finest quality components. Buckingham offers a wide selection of Arborist Saddle
More informationSerial Number: Lot Number: Purchase Date: General Factors Accepted / Rejected Supportive Details or Comments. Accepted Rejected.
Full Body Harness Harness Model: General Factors / Supportive Details or Comments 1.) Hardware: (includes D-rings, buckles, keepers, and back pads) Inspect for damage, distortion, sharp edges, burrs, cracks
More informationMONTHLY HARNESS INSPECTION REGISTER JANUARY 2015
www.approvedaccess.co.uk info@approvedaccess.co.uk MONTHLY HARNESS REGISTER The Custodian of this Register is: JANUARY 2015 THE OPERATIVES LISTED BELOW HAVE RECEIVED INFORMATION AND INSTRUCTION REGARDING
More informationFall Protection. Fall Speed vs. Reaction Time. Good body reaction time = 0.5 seconds Travel distance in 0.5 seconds = 4 feet (1.21mts.
Fall Protection Fall Speed vs. Reaction Time Good body reaction time = 0.5 seconds Travel distance in 0.5 seconds = 4 feet (1.21mts.) In 1 second your body will fall 16 feet (4.8 mts.) By the time you
More informationFall Speed vs. Reaction Time
Fall Protection Fall Speed vs. Reaction Time Good body reaction time = 0.5 seconds Travel distance in 0.5 seconds = 4 feet (1.21mts.) In 1 second your body will fall 16 feet (4.8 mts.) By the time you
More informationSafe Work Method Statement LRB TREE SERVICES 6 Behland St, Kearneys Spring QLD, 4350 ABN
JOB NO: PROJECT: DATE: 1/1/2018 SWMS NO: SWMS 001.1 PREPARED BY: LUKE BLINCO REVISED BY: ACTIVITY: TREE REMOVAL & PRUNING SIGNED BY: REVISION DATE: MINIMUM PERSONAL PROTECTIVE EQUIPMENT (PPE) REQUIREMENTS
More informationDecember 2012 Safety Meeting. Fall Protection Answer Key 1. B 2. B 3. D 4. B 5. D 6. C 7. A 8. C 9. D 10. A KEY-SM-FALLPROT V.A.0.
Fall Protection Answer Key December 2012 Safety Meeting Below is the answer key for the quiz. 1. B 2. B 3. D 4. B 5. D 6. C 7. A 8. C 9. D 10. A KEY-SM-FALLPROT Fall Protection 1 Introduction to Fall Protection
More informationUser Instructions 1789 Parapet Wall Anchor
User Instructions 1789 Parapet Wall Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee training program as required
More informationProduct Name: Concrete Anchor Strap
Product Name: Concrete Anchor Strap Part #: 10705; 10710; 10715 ; 10717; 10720 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Table
More informationIMPORTANT: If you have questions on the use, care, application, or suitability of this equipment contact DBI/SALA.
Model Numbers: (See back cover for model numbers) User Instruction Manual Body Belts for Personal Restraint Applications This manual ishould be used as part of an employee training program as required
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 88004X Series D-Ring Extender 5000 lb Rated Connector Complies with ANSI Z359.1-1998, ANSI 10.14 and OSHA 1926 regulations and requirements. Reliance Industries P.O. Box 2046 Deer
More informationTower Climber Orientation.
www.natehome.com Disclaimer: Thank you for supporting the National Association of Tower Erectors (NATE) with your participation in this online orientation course. This program is designed as a resource
More informationInspection & Maintenance
PERSONAL FALL ARREST EQUIPMENT Inspection & Maintenance This article addresses the requirements of OSHA1926.502(d)(21), which states that personal fall arrest systems shall be inspected prior to each use
More informationTree Trimming, Pruning and Removal
Tree Trimming, Pruning and Removal Training (updated 1/18/13) 1. Take Control of Your Own Safety Objectives 1. Name the most common types of tree trimming accidents. 2. Interpret the meaning of common
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 68XXXX Series Anchorage Slings Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046 Deer Park, TX 77536
More informationProduct Name: Hold Me Rope Anchor
Product Name: Hold Me Rope Anchor Part #: 01300 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety
More informationInstructions for The Rose Crossover Style Full Body Harness For Women
P.O. Box 3026 Sherwood Park Alberta T8H 2T1 Phone: (780) 464-7139 Fax: (780) 464-7652 e-mail: inquiries@ safetydirect.ca Web site: www.safetydirect.ca Instructions for The Rose Crossover Style Full Body
More informationInstructions for Dual Retractable Web lanyards Type 1. Instructions for E6 Energy Absorbing Y, Bypass Lanyards. For Worker Mass Range of 90 to 175 kg
P.O. Box 3026 Sherwood Park Alberta T8H 2T1 Phone: (780) 464-7139 Fax: (780) 464-7652 e-mail: inquiries@ safetydirect.ca Web site: www.safetydirect.ca Instructions for Dual Retractable Web lanyards Type
More informationOPE Training Seminar Agenda
OPE Training Seminar Agenda Basics -OSHA - Industry Symbols - A,B,C s - Types of OPE Systems - Selection of an OPE System - Inspection & Maintenance - Safety Tips (OSHA) OCCUPATION SAFETY AND HEALTH ADMINISTRATION
More informationErgoLite P/N 17904, & J17904, J17906 Series Saddle Instructions/Warnings
ErgoLite P/N 17904, 17906 & J17904, J17906 Series Saddle Instructions/Warnings The ErgoLite arborist saddle is designed for the professional arborist. It is fully adjustable at the waist, legs and suspension
More informationRescue ladder System. User Instruction Manual
User Instruction Manual for: Rescue Ladder System (Model Numbers: Ladder - 8516294, Hanging Plate Bracket - 8516316) User Instruction Manual Rescue ladder System This manual is intended to meet the Manufacturer
More informationTREE SPIDER Safety Line Models: TSSL, TSSL3PK
TREE SPIDER Safety Line Models: TSSL, TSSL3PK INSTRUCTION MANUAL READ AND FOLLOW ALL SAFETY WARNINGS AND INSTRUCTIONS IN THIS MANUAL. Do not throw away. Keep for future reference. PH: 507-263-4484 (8 a.m.-
More informationInstructions for Y Style Full Body Harness Model YH130
P.O. Box 3026 Sherwood Park Alberta T8H 2T1 Phone: (780) 464-7139 Fax: (780) 464-7652 e-mail: inquiries@ safetydirect.ca Web site: www.safetydirect.ca Instructions for Y Style Full Body Harness Model YH130
More informationFall Protection PPT-SM-FALLPROT V.A.0.0
Fall Protection 1 Introduction to Fall Protection Falls account for 13% of fatal injuries 11% of these fatal falls were to a lower level Workers may be required to perform tasks at great heights which
More informationYOU MUST LEARN TO MID LINE DESCEND ON YOUR FIRST CLIMB!
Climb Training Orientation for Beginning Ascending and Descending. YOU MUST LEARN TO MID LINE DESCEND ON YOUR FIRST CLIMB! Knots to Learn Rethread Figure Eight Eight on a bight Double Fishermen Water knot
More informationRisk Assessment (RA) Link to template
Risk Assessment (RA) Link to template The RISK ASSESSMENT looks on three main things: The job The tree The surroundings We can minimize hazards if an accident occur by: Identifying the possible risk Evaluate
More informationUSER INSTRUCTIONS LARGE HOOK & STRAP ANCHORAGE CONNECTOR ! WARNING
ROSE MODEL NUMBER USER INSTRUCTIONS LARGE HOOK & STRAP ANCHORAGE CONNECTOR! WARNING National standards and state, provincial and federal laws require the user to be trained before using this product. Use
More informationPart #: 15158; 15159; 15188; 61027; 61029; 61140; 61141
Product Name: Guardrail Receivers Part #: 15158; 15159; 15188; 61027; 61029; 61140; 61141 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment!
More informationProduct Name: Internal Shock Lanyard
Product Name: Internal Shock Lanyard Part #: 11200; 11201; 11202; 11203; 21215; 01295; 01296; 01297; 01298; 11211; 11212; 11213; 11260; 11261 Instruction Manual Do not throw away these instructions! Read
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 714XXX Series Lanyard Extender Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046 Deer Park, TX 77536
More informationProduct Name: Angel Anchor
Product Name: Angel Anchor Part #: 00260 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards
More informationSection 16B. Fall Protection. Falls are the second leading cause of death in the workplace. Factors contributing to falling incidents:
Section 16B. Fall Protection Falls are the second leading cause of death in the workplace. Factors contributing to falling incidents: 1. Personal factors Lack of concentration. Use of medication. Poor
More informationNOTE WARNING! PHOENIX, AZ USA USER INSTRUCTION MANUAL WATCH VIDEOS 6, 12 & 25 ON ULTRASAFEUSA.COM MODEL: SIZE: DATE:
MODEL: 1-800-850-5914 PHOENIX, AZ USA SIZE: DATE: USER INSTRUCTION MANUAL DESCRIPTION: HARNESS NOMEX / KEVLAR F.R. MODEL: 96305NK, 96305K, 96396BKQL, 96305NK, U-96350KQLMX, 96305K, U-96396BKQLMXTP MEETS
More informationUSER S INSTRUCTION MANUAL FOR THE INSTALLATION, OPERATION & MAINTENANCE OF THE GUARDIAN TEMPORARY HORIZONTAL LIFELINE SYSTEM
USER S INSTRUCTION MANUAL FOR THE INSTALLATION, OPERATION & MAINTENANCE OF THE GUARDIAN 04630 TEMPORARY HORIZONTAL LIFELINE SYSTEM 1 WARNING This is a design compatible component for a comprehensive Guardian
More informationZIGZAG Experience. Important / remember. Failure to heed any of these warnings may result in severe injury or death.
A. Childeric / Copalme ZIGZAG Experience This "Product Experience" document is a supplement to the Instructions For Use, which provides feedback from field experience and tips for using your product It
More informationGENERAL GUIDELINES FOR PROPER RIGGING PRACTICES AND INSPECTION & REMOVAL CRITERIA FOR SLINGS PER OSHA
GENERAL GUIDELINES FOR PROPER RIGGING PRACTICES AND INSPECTION & REMOVAL CRITERIA FOR SLINGS PER OSHA 1910.184 SAFE OPERATING PRACTICES -.Whenever any sling is used, the following practices shall be observed:
More informationUse of the Climbing wall at Pendle Vale College. Method statement and risk assessment
Use of the Climbing wall at Pendle Vale College Method statement and risk assessment Updated June 2015 Using the Climbing Wall The climbing wall is to be used only under supervision from member of staff
More informationSection 31 TABLE OF CONTENTS Tree Maintenance and Removal. 31.A General B Tree Climbing C Felling
Section 31 TABLE OF CONTENTS Tree Maintenance and Removal Section: Page 31.A General... 31-1 31.B Tree Climbing... 31-3 31.C Felling... 31-7 31.D Brush Removal and Chipping... 31-10 31.E Other Operations
More informationProduct Name: Snappy Anchor
Product Name: Snappy Anchor Part #: 00710; 00711; 00715-TV Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable
More informationTree Worker A MONTHLY RESOURCE FOR TREE CARE PROFESSIONALS k OCTOBER 2016 Number 404
Tree Worker A MONTHLY RESOURCE FOR TREE CARE PROFESSIONALS k OCTOBER 2016 Number 404 Back to Basics: Rigging Slings I find myself wanting to review or get back to the basics sometimes on different things.
More informationProduct Name: Edge Series Web SRL
Product Name: Edge Series Web SRL Part #: 10900; 10901, 10909, 20900 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction
More informationDeveloped by Firefighter Ty Drage January NFPA 1670 Standard on Operations and Training for Technical Search and Rescue Incidents
Q UICK A CCESS K IT (1.1) Developed by Firefighter Ty Drage January 2011 NFPA 1670 Standard on Operations and Training for Technical Search and Rescue Incidents T ASK S KILL DESCRIPTION AND DETAIL Every
More informationINSTRUCTIONS FOR USE
Rebar Chain Assembly INSTRUCTIONS FOR USE 7260XX Rebar Chain Assembly Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046
More informationProduct Name: Edge Angel SRL
Product Name: Edge Angel SRL Part #: 10920; 10922; 10925 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable
More informationIRATA International code of practice for industrial rope access. Part 3: Informative annexes Annex H: Equipment inspection checklist
IRATA International code of practice for industrial rope access Part 3: Informative annexes Annex H: inspection checklist September 2013 The first edition of Annex H was published in December 2010. This
More informationCORPORATE SAFETY MANUAL
CORPORATE SAFETY MANUAL Procedure No. 32-0 Revision: Date: May 2005 Total Pages: 10 PURPOSE To provide general guidelines for the inspection of all ropes, chains, cables, slings, etc. used for personnel
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 7100 Series Lanyards Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046 Deer Park, TX 77536 Phone :
More information1.0 Purpose: To provide guidelines for selection, usage, inspection and rejection of rigging equipment
Orignal Issue Date : 28-10-10 Date of Revision: Page- - 1-1.0 Purpose: To provide guidelines for selection, usage, inspection and rejection of rigging equipment (Slings & Ropes) 2.0 Reference: 3.0 Associated
More informationOCCUPATIONAL HEALTH AND SAFETY ACT FALL PROTECTION REGULATIONS
c t OCCUPATIONAL HEALTH AND SAFETY ACT FALL PROTECTION REGULATIONS PLEASE NOTE This document, prepared by the Legislative Counsel Office, is an office consolidation of this regulation, current to June
More informationProduct Name: Universal Guardrail Post
Dist. by: BEST MATERIALS Ph: 800-474-7570 www.bestmaterials.com Email: Sales@BestMaterials.com Product Name: Universal Guardrail Post Part #: 61133; 61135; 61136 Instruction Manual Do not throw away these
More informationMATERIAL HANDLING - FIELD RIGGING SAFETY PROGRAM
Title: Material Handling - Rigging Effective Date: 12/4/2014 Control Number: THG_0049 Revision Number: 1 Date: 10/23/2015 Annual Review Completed: 5/13/2015 MATERIAL HANDLING - FIELD RIGGING SAFETY PROGRAM
More informationInstallation, Operating, Inspection and Maintenance Instructions Ladder Climber s Safety System. Warning
OWNER'S MANUAL Installation, Operating, Inspection and Maintenance Instructions Ladder Climber s Safety System Model # s: 6000, 6001, 6010 Warning You must read and fully understand all instructions, or
More informationFall Protection ABC s
Fall Protection ABC s Chris Caron American Safety & Supply, Inc. Fall Protection ABC Itinerary Review types of fall arrest systems Review and discuss ladder safety Discuss the various components of fall
More informationHARNESSES / Available in S, M, L & XL
WINTER 2018 Tools & Safety Equipment for the Rope Access Worker VOL. 1 HARNESSES / Available in S, M, L & XL S1 Safety Harness 66772 The S1 Safety harness was designed by the experts at Safety One Training
More informationProduct Name: 2-Way Standing Seam Roof Clamp. Instruction Manual. Part #: 10600
Product Name: 2-Way Standing Seam Roof Clamp Part #: 10600 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Table of Contents Introduction
More informationFigure 1 - Parts Identification. Copyright 2002, DB Industries, Inc.
User Instruction Manual Zorbit Energy Absorber Kits for Horizontal Lifeline Systems This manual is provided as the Maunfacturer s Instructions, and should be used as part of an employee training program
More informationWARNING! DO NOT THROW AWAY THESE INSTRUCTIONS! READ AND UNDERSTAND BEFORE USING EQUIPMENT!
Guardian Fall Protection Kent, WA 800-466-6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment shall
More informationANCHORAGE STRAPS INSTRUCTION MANUAL
ANCHORAGE STRAPS INSTRUCTION MANUAL THE INSTRUCTIONS APPLIES TO THE FOLLOWING MODELS: EZA6350 4' Cross Anchor Strap for Concrete EZA635 6' Cross Anchor Strap for Concrete CONCRETE ANCHOR WEB STRAPS INSTRUCTIONS
More informationProduct Name: Non-Shock Lanyard
Product Name: Non-Shock Lanyard Part #: 01121, 01122; 01280, 01250, 01255, 01260, 01265, 01251, 01261, 01265, 01270, 01271 Instruction Manual Do not throw away these instructions! Read and understand these
More informationPremium PowerPoint Presentation. Rigging Review
Premium PowerPoint Presentation Rigging Review Chapter 1 Hoisting Safety Review: What about the CG Symmetrical vs. Asymmetrical Balanced and Unbalanced Lifting Lug Hooks Angle Deformation Safety Gates
More informationClimbing Area. Review Completed by: Jamie Brunt Approved By: Steve Allard Date: June 2012
Topic/Activity/Issue: Climbing Area Page: 1 of 5 TASK/ OPERATION: Operating Climbing Wall Operating Procedure Developed by: Steve Allard Manager Paccar Scout Camp Approved By: Steve Allard Date: 23/11/10
More informationZIGZAG Experience. Important / remember. Failure to heed any of these warnings may result in severe injury or death.
A. Childeric / Copalme ZIGZAG Experience This "Product Experience" document is a supplement to the Instructions For Use, which provides feedback from field experience and tips for using your product It
More informationSAFE WORK PROCEDURE. Location of Equipment Written By: Approved By: Date Created Last Revision
Page 1 of 5 Location of Equipment Written By: Approved By: Date Created Last Revision School: Facilities & Operations Brent Vandenbosch Gordon Howe October 14, 2009 new Room: n/a Barry Hamilton HAZARDS
More informationPURPOSE: The purpose of this Operating Policy/Procedure (OP) is to ensure that material handling devices are used correctly and safely.
[Date changed posted 10/3/17 (replaces 10/31/12 edition)] Operating Policy and Procedure : Material Handling Devices DATE: October 3, 2017 PURPOSE: The purpose of this Operating Policy/Procedure (OP) is
More informationSlings Natural Rope, Synthetic Rope and Synthetic Web
Optional Information Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: Slings Natural Rope, Synthetic Rope and Synthetic Web Self Inspection Checklist Guidelines:
More informationRIGGERS SAFETY SAFETY IS IN THE DETAILS FULL LINE CATALOG
RIGGERS SAFETY SAFETY IS IN THE DETAILS FULL LINE CATALOG Riggers Safety is a California-based manufacturer of Personal Fall Arrest Systems (PFAS) and Fall Prevention Products. Our automated manufacturing
More informationProduct Name: Bull Ring Anchor
Product Name: Bull Ring Anchor Part #: 00484 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards
More informationRescue Ladder Basic Kit Model: FS-EX243 18ft (5.48m)
Rescue Ladder Basic Kit Model: FS-EX243 18ft (5.48m) IMPORTANT!!! ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS
More informationUser Instruction Manual For Davit Rescue System
Instructions for the following series products: Rescue Davit System Model numbers 8004000 and 8302500 User Instruction Manual For Davit Rescue System This manual should be used as part of an employee training
More informationModule Overview Module Description Not a substitute for standards. Training should not be considered as substitute for safety and health standards for
Module Overview Fall Protection Equipment Module Description Basic guidelines and methods. Selection, inspection and maintenance of fall protection equipment to include: body belt. full body harness. lanyard.
More informationSelf Retracting Device User Instruction Manual
6.3 INSPECTION AND MAINTENANCE LOG CONTINUED: Model: Serial #: Date of Mfg: Class: SRL SRL-R SRL-LE INSPECTION DATE INSPECTION ITEMS NOTED CORRECTIVE ACTION MAINTENANCE PERFORMED Web Devices Fall Arrest
More informationProduct Name: 2-Way Standing Seam Roof Clamp
Product Name: 2-Way Standing Seam Roof Clamp Part #: 10600 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable
More informationRIGGERS SAFETY SAFETY IS IN THE DETAILS FULL LINE CATALOG
RIGGERS SAFETY SAFETY IS IN THE DETAILS FULL LINE CATALOG Riggers Safety is a California-based manufacturer of Personal Fall Arrest Systems (PFAS) and Fall Prevention Products. Our automated manufacturing
More information1 of 15. Policy Number 61. Last Update: March 21, Effective Date: 11/22/11 Resolution No Title: Fall Protection Policy POLICY STATEMENT
Policy Number 61 Effective Date: 11/22/11 Resolution No. 476-11 Title: Fall Protection Policy Last Update: March 21, 2011 POLICY STATEMENT The objective of the Cayuga County (County) Fall Protection Policy
More informationProduct Name: Rope Grab
Product Name: Rope Grab Part #: 01500; 01503; 01505; 01506; 01507; 01511 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction
More informationBasic Rigging Knots. Clove hitch: primarily used to secure branches which are being rigged. To secure this hitch from rolling
Clove hitch: primarily used to secure branches which are being rigged. To secure this hitch from rolling out under load during rigging, it is vital to secure the tail end of the rope around the standing
More informationRigging Safety. 1 Copyright 2014 by PEC Safety Management, Inc. PPT-SM-RIGGING 2014
Rigging Safety 1 Copyright by PEC Safety Management, Inc. Rigger Role Assist the crane operator by properly attaching and detaching loads the crane Know how to safely connect and disconnect loads Discuss
More informationCabling. Cabling. Crown stabilisation. Overload indicator tree save. Accessories
Cabling Cabling 53 54 55-56 57 Crown stabilisation Overload indicator Accessories Crown stabilisation Trees in urban environments are subject to extensive human interference. In general terms, urban living
More informationUser Instruction Manual Roof Anchor and / Sayfline Horizontal Lifeline System
Instructions for the following series products: Roof Anchor (See back page for specific model numbers.) User Instruction Manual 2103673 Roof Anchor and 76002001/7600202 Sayfline Horizontal Lifeline System
More informationQO9.d.. e v -.PXresat
BEFORE THE BOARD OF COUNTY COMMISSIONERS, COWLITZ COUNTY, WA. In the Matter of Rescinding Res. No. 93-037 Adopted 3-8 -1993 and Adopting The Updated Fall Protection Policy RESOLUTION NO. 3 n 2 WHEREAS,
More informationFALL-TEK RESCUE SOLUTION
FALL-TEK RESCUE SOLUTION KT36168 KT36169 KT36170 KT36175 Manufacturer s Instructions PMIROPE.COM T 1-800-282-ROPE Solutions and Kits Solutions This page is intentionally blank. PRODUCT DESCRIPTION PMI
More informationBuckingham Mfg. Co. Inc.
Buckingham Mfg. Co. Inc. ERGOVATION Batten Seat Attachment (PN 1368) Accessory Assembly Instructions Step 1 Note: There are 2 ways that this attachment can be used on the Ergovation saddle / sit harness.
More informationBasic Rigging And Wire Rope
Basic Rigging And Wire Rope Presented By Master Builders of Iowa Basic Rigging and Wire Rope Topics Four Commandments of Rigging Sling Angles Types Of Hitches Types Of Slings Types Of Rigging Devices OSHA
More information1.2 LIMITATIONS: Consider the following application limitations before using this equipment:
User Instruction Manual Standing Seam Roof Anchor This manual is intended to meet the Manufacturer s Instructions, and should be used as part of an employee training program as required by OSHA. Figure
More informationCOPYRIGHT 2014 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
The following material is being provided for informational purposes and in order to promote safety awareness. It does not constitute nor should it serve as a substitute for legal or other professional
More informationTOWER-TEK RESCUE SOLUTION
TOWER-TEK RESCUE SOLUTION KT36171 (25m) KT36172 (100m) KT36173 (122m) Manufacturer s Instructions PMIROPE.COM T 1-800-282-ROPE SOLUTIONS & KITS SOLUTIONS This page is intentionally blank. PRODUCT DESCRIPTION
More informationSURVIVING THE FALL: Leader s Guide. The Proper Use Of Your Personal Fall Arrest System. ERI Safety Videos
2911 SURVIVING THE FALL: The Proper Use Of Your Personal Fall Arrest System Leader s Guide ERI Safety Videos SURVIVING THE FALL: The Proper Use Of Your Personal Fall Arrest System This easy-to-use Leader
More informationFALL PROTECTION / ELEVATED WORK
SEPTEMBER CORE REFRESHER HSE TOOL BOX FALL PROTECTION / ELEVATED WORK FALL PROTECTION Falls from elevations are one of the most common causes of death in this industry. OSHA requires fall protection when
More informationBuckingham Mfg. Co., Inc. OX BLOCK TM Instructions and Warnings
OVERVIEW The Buckingham OX BLOCK is a rope snatch block with an integrated friction bar used for lowering loads, snubbing loads, and raising loads. It allows the rigging professional to handle loads with
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 8000 Series Full Body Harnesses Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046 Deer Park, TX 77536
More informationRescue Ladder Model: KT ft (5.48m)
Rescue Ladder Model: KT36164 18ft (5.48m) IMPORTANT!!! ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS SHOULD BE
More informationSOUTH LYON FIRE DEPARTMENT Manual of Procedures 403
PERSONAL PROTECTIVE EQUIPMENT Issued: June 1, 2012 Revised: September 25, 2015 Approved: Chief Mike Kennedy I. SCOPE This procedure applies to all employees required to work in hazardous environments.
More information