Vehicle-mounted elevating and rotating work platforms.
|
|
- Mary Riley
- 10 months ago
- Views:
Transcription
1 Regulations (Standards - 29 CFR) Vehicle-mounted elevating and rotating work platforms Regulations (Standards - 29 CFR) - Table of Contents Part Number: 1910 Part Title: Occupational Safety and Health Standards Subpart: F Subpart Title: Powered Platforms, Manlifts, and Vehicle-Mounted Work Platforms Standard Number: Title: Vehicle-mounted elevating and rotating work platforms (a) "Definitions applicable to this section" (a)(1) "Aerial device." Any vehicle-mounted device, telescoping or articulating, or both, which is used to position personnel (a)(2) "Aerial ladder." An aerial device consisting of a single- or multiple-section extensible ladder (a)(3) "Articulating boom platform." An aerial device with two or more hinged boom sections (a)(4) "Extensible boom platform." An aerial device (except ladders) with a telescopic or extensible boom. Telescopic derricks with personnel platform attachments shall be considered to be extensible boom platforms when used with a personnel platform (a)(5) "Insulated aerial device." An aerial device designed for work on energized lines and apparatus (a)(6) "Mobile unit." A combination of an aerial device, its vehicle, and related equipment.
2 (a)(7) (a)(7) "Platform." Any personnel-carrying device (basket or bucket) which is a component of an aerial device (a)(8) "Vehicle." Any carrier that is not manually propelled (a)(9) "Vertical tower." An aerial device designed to elevate a platform in a substantially vertical axis (b) "General requirements." (b)(1) Unless otherwise provided in this section, aerial devices (aerial lifts) acquired on or after July 1, 1975, shall be designed and constructed in conformance with the applicable requirements of the American National Standard for "Vehicle Mounted Elevating and Rotating Work Platforms," ANSI A , including appendix, which is incorporated by reference as specified in Aerial lifts acquired for use before July 1, 1975 which do not meet the requirements of ANSI A , may not be used after July 1, 1976, unless they shall have been modified so as to conform with the applicable design and construction requirements of ANSI A Aerial devices include the following types of vehiclemounted aerial devices used to elevate personnel to jobsites above ground: (b)(1)(i) Extensible boom platforms, (b)(1)(ii) (b)(1)(ii) aerial ladders, (b)(1)(iii) articulating boom platforms, (b)(1)(iv)
3 vertical towers, and (b)(1)(v) a combination of any of the above. Aerial equipment may be made of metal, wood, fiberglass reinforced plastic (FRP), or other material; may be powered or manually operated; and are deemed to be aerial lifts whether or not they are capable of rotating about a substantially vertical axis (b)(2) Aerial lifts may be "field modified" for uses other than those intended by the manufacturer, provided the modification has been certified in writing by the manufacturer or by any other equivalent entity, such as a nationally recognized testing laboratory, to be in conformity with all applicable provisions of ANSI A and this section, and to be at least as safe as the equipment was before modification (b)(3) The requirements of this section do not apply to firefighting equipment or to the vehicles upon which aerial devices are mounted, except with respect to the requirement that a vehicle be a stable support for the aerial device (b)(4) For operations near overhead electric power lines, see (c)(3) (c) (c) "Specific requirements" (c)(1) "Ladder trucks and tower trucks." Before the truck is moved for highway travel, aerial ladders shall be secured in the lower traveling position by the locking device above the truck cab, and the manually operated device at the base of the ladder, or by other equally effective means (e.g., cradles which prevent rotation of the ladder in combination with positive acting linear actuators) (c)(2) "Extensible and articulating boom platforms." (c)(2)(i) Lift controls shall be tested each day prior to use to determine that such controls are in safe
4 working condition (c)(2)(ii) Only trained persons shall operate an aerial lift (c)(2)(iii) Belting off to an adjacent pole, structure, or equipment while working from an aerial lift shall not be permitted (c)(2)(iv) Employees shall always stand firmly on the floor of the basket, and shall not sit or climb on the edge of the basket or use planks, ladders, or other devices for a work position (c)(2)(v) A body belt shall be worn and a lanyard attached to the boom or basket when working from an aerial lift (c)(2)(vi) Boom and basket load limits specified by the manufacturer shall not be exceeded (c)(2)(vii) The brakes shall be set and outriggers, when used, shall be positioned on pads or a solid surface. Wheel chocks shall be installed before using an aerial lift on an incline (c)(2)(viii) (c)(2)(viii) An aerial lift truck may not be moved when the boom is elevated in a working position with men in the basket, except for equipment which is specifically designed for this type of operation in accordance with the provisions of paragraphs (b)(1) and (b)(2) of this section (c)(2)(ix) Articulating boom and extensible boom platforms, primarily designed as personnel carriers, shall have both platform (upper) and lower controls. Upper controls shall be in or beside the platform within easy reach of the operator. Lower controls shall provide for overriding the upper controls. Controls shall be plainly marked as to their function. Lower level controls shall not be operated unless permission has been obtained from the employee in the lift, except in case of emergency.
5 (c)(2)(x) Climbers shall not be worn while performing work from an aerial lift (c)(2)(xi) The insulated portion of an aerial lift shall not be altered in any manner that might reduce its insulating value (c)(2)(xii) Before moving an aerial lift for travel, the boom(s) shall be inspected to see that it is properly cradled and outriggers are in stowed position, except as provided in paragraph (c)(2)(viii) of this section (c)(3) (c)(3) "Electrical tests." Electrical tests shall be made in conformance with the requirements of ANSI A , Section 5. However, equivalent DC voltage tests may be used in lieu of the AC voltage test specified in A DC voltage tests which are approved by the equipment manufacturer or equivalent entity shall be considered an equivalent test for the purpose of this paragraph (c)(3) (c)(4) "Bursting safety factor." All critical hydraulic and pneumatic components shall comply with the provisions of the American National Standards Institute standard, ANSI A , Section 4.9 Bursting Safety Factor. Critical components are those in which a failure would result in a free fall or free rotation of the boom. All noncritical components shall have a bursting safety factor of at least two to one (c)(5) "Welding standards." All welding shall conform to the following Automotive Welding Society (AWS) Standards which are incorporated by reference as specified in , as applicable: (c)(5)(i) Standard Qualification Procedure, AWS B (c)(5)(ii) Recommended Practices for Automotive Welding Design, AWS D
6 (c)(5)(iii) Standard Qualification of Welding Procedures and Welders for Piping and Tubing, AWS D (c)(5)(iv) Specifications for Welding Highway and Railway Bridges, AWS D [39 FR 23502, June 27, 1974, as amended at 40 FR 13439, Mar. 26, 1975; 55 FR 32014, Aug. 6, 1990; 61 FR 9227, March 7, 1996]
Aerial Lift Safety Program
Aerial Lift Safety Program Revision Date: 6-19-2017 TABLE OF CONTENTS Aerial Lift Safety Program 1.0 Overview... 3 2.0 Policy......3 3.0 Requirements. 3 4.0 Purpose..... 4 5.0 Scope.........4 6.0 Responsibilities........7
Pannier Corporation Health and Safety Handbook Marking System Group Aerial Lifts Original Date: Section: Revision date: Page: 12/5/ of 11
12/5/2013 37 1 of 11 1.0 Overview Aerial lifts are commonly used in construction, inspection, athletic events and repair services to lift Pannier employees to an elevated work position. Proper operation
OSHA Federal Standards October 1, 2014 September 30, 2015
OSHA Federal Standards October 1, 2014 September 30, 2015 29 CFR 29 CFR 1910 1910. SUBPARTS MOST FREQUENTLY CITED SERIOUS VIOLATIONS IN GENERAL INDUSTRY 2015 K N D S J O I Z O Z HAZARD COMMUNICATION WRITTEN
Quiz. telescoping. designed to. established. 1 Pag. EWP Pre Reading
EWP Pre Reading and Quiz Due to the intensivee nature of our EWP course, it is mandatory that you study this manual thoroughly before attending your course. Doing so will ensure you have the best possible
2.2. Anchorage Point A secure point of attachment for Lifelines, lanyards or deceleration devices.
Title: Elevated Walking/Working Surfaces (Fall Protection) Site Function: Safety Procedure No.: MC032.122 Page: 1 of 16 McIntosh Site Reviewed: 02/2013 Effective: 03/2013 Supersedes: 08/2012 Preparer:
F A C I L I T A T O R S G U I D E
Aerial Lift Safety FA C I L I TAT O R S G U I D E What s Inside Facilitator s Guide a Overview b Getting Started d Presentation Guidelines f Lesson Plan h Frequently Asked Questions 1 Introduction 2 The
SYDNEY TRAMWAY MUSEUM WORKING ON ELEVATED PLATFORMS PROCEDURE
WORKING ON ELEVATED PLATFORMS PROCEDURE DECEMBER 2008JANUARY 2014 1. Document Details: SYDNEY TRAMWAY MUSEUM Document Control Record Name: Working On Elevated Platforms Procedure Number STM 6161 Version
Reviewed: New Effective: 5/18/12 Supersedes: New Preparer: Owner: Approver: Team Member, Occupational Safety Industrial Hygiene
Procedure No.: BC032.027 Page: 1 of 15 Preparer: Owner: Approver: Team Member, Occupational Safety Industrial Hygiene Manager, Occupational Safety Industrial Hygiene Vice President, Ecology & Safety (Signature
OSHA 29CFR 1910 Subpart D Walking-Working Surfaces Content
OSHA 29CFR 1910 Subpart D Walking-Working Surfaces Content 1910.28 Duty to have Fall Protection and Falling Object Protection 1910.29 Fall Protection Systems and Falling Object Protection Criteria and
Fall Protection ABC s
Fall Protection ABC s Chris Caron American Safety & Supply, Inc. Fall Protection ABC Itinerary Review types of fall arrest systems Review and discuss ladder safety Discuss the various components of fall
Reporting, Recording & more Walking Working Surfaces Local Emphasis Program Your Questions
Reporting, Recording & more Walking Working Surfaces Local Emphasis Program Your Questions As of January 1, 2015, employers must report the following to OSHA: All work-related fatalities within 8 hours
Operator's Manual Supplement
Operator's Manual Supplement Traveling Fall Arrest Anchor System Original Instructions First Edition Fifth Printing Part No. 1256390GT Operator's Manual Supplement Genie Self-propelled Boom Products and
OSHA Regulatory Update
OSHA Regulatory Update New Walking-Working Surfaces and PPE (Fall Protection) Rule Maggie Miracle Safety and Occupational Health Manager OSHA Objectives Purpose of the New Rule Benefits of the New Rule
Aerial Lift Safety Program
Aerial Lift Safety Program 0 Program Contents Introduction 2 Regulatory Basis..2 Operational Safety Precautions.3 Hazard Avoidance 3 1. Electrocution.3 2. Tip Over and Collapse.4 3. Falls.5 4. Collision
Key provisions of OSHA's new rule on walking/working surfaces, fall protection
ARTICLES CASES Key provisions of OSHA's new rule on walking/working surfaces, fall protection Although an overwhelming majority of general industry accidents stem from slips, trips and falls, Subpart D
FALL PROTECTION AND RESCUE PLAN NS-MAYPORT BLDG RENOVATION PROJECT. (Revised Copy 11/19/2010)
FALL PROTECTION AND RESCUE PLAN NS-MAYPORT BLDG. 1553 RENOVATION PROJECT (Revised Copy 11/19/2010) 1 TABLE OF CONTENTS 1.0 SCOPE AND PERSONNEL RESPONSIBLE FOR THE PLAN 2.0 STATEMENT OF COMPANY POLICY 3.0
Fall Protection PPT-SM-FALLPROT V.A.0.0
Fall Protection 1 Introduction to Fall Protection Falls account for 13% of fatal injuries 11% of these fatal falls were to a lower level Workers may be required to perform tasks at great heights which
Walking-Working Surfaces
Walking-Working Surfaces 29 CFR 1910, Subpart D Presented by: Chesapeake Region Safety Council Rod Markley, CSP, CHST, CET Subpart D - Walking-Working Surface Topics we will cover: Background of rule Overview
Thanks To Our Sponsors Platinum Sponsor NS Department of Labour and Workforce Development
March 25, 26, 27, 2009 Thanks To Our Sponsors Platinum Sponsor NS Department of Labour and Workforce Development Special Event Sponsor Workers Compensation Board of Nova Scotia Gold Sponsors Maxwell Promotions
ELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR CFR , ,
ELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.331 335-29 CFR 1926.302, 1926.416, 1926.417 BASIS: The National Safety Council estimates that there are at least 300 deaths
SAFETY HARNESSES IN MOBILE ELEVATING WORK PLATFORMS
SAFETY HARNESSES IN MOBILE ELEVATING WORK PLATFORMS BOOM TYPE PLATFORMS It is strongly recommend that a full body harness with an adjustable lanyard (used to provide work restraint and adjusted to be as
Operator's Manual Supplement
Operator's Manual Supplement Cribbing Instructions First Edition Sixth Printing Part No. 82943GT Operator's Manual Supplement Front Matter Important Contents Plywood cribbing may be used to provide a level
Sample Fall Rescue Plan for Bridge Work
This document is intended to provide guidance for developing fall rescue plans for bridge contractors. The Occupational Safety and Health Administration s (OSHA) regulation 29 CFR 1926.502(d)(20) states:
OCCUPATIONAL HEALTH AND SAFETY ACT FALL PROTECTION REGULATIONS
c t OCCUPATIONAL HEALTH AND SAFETY ACT FALL PROTECTION REGULATIONS PLEASE NOTE This document, prepared by the Legislative Counsel Office, is an office consolidation of this regulation, current to June
In This Document. OBJECTIVES Upon completion of this module, you should be able to:
Struck By Fact Sheet MODULE DESCRIPTION This module provides information that will enable you to recognize common struck-by hazards at construction worksites. OBJECTIVES Upon completion of this module,
Respiratory Protection Self-Inspection Checklist
Respiratory Protection Self-Inspection Checklist Guidelines: This checklist applies to the use of either atmosphere-supplying or air-purifying respirators being worn, voluntarily or otherwise, for comfort
DEPARTMENT OF LICENSING AND REGULATORY AFFAIRS AND INDUSTRY SERVICES DIRECTOR S OFFICE BUREAU OF SAFETY AND REGULATION
DEPARTMENT OF LICENSING AND REGULATORY AFFAIRS AND INDUSTRY SERVICES CONSUMER DIRECTOR S OFFICE BUREAU OF SAFETY AND REGULATION GENERAL INDUSTRY SAFETY AND HEALTH STANDARD GENERAL INDUSTRY SAFETY STANDARDS
ARKANSAS TECH UNIVERSITY FACILITIES MANAGMENT HEALTH AND SAFETY MANUAL
FALL PROTECTION (PERSONAL FALL ARREST SYSTEMS) 15.0 The purpose of this policy is to specify procedures and training for the safety of the employees in the Facilities Management Group while working on
FALL PROTECTION PROGRAM
FALL PROTECTION PROGRAM 1.0 PURPOSE: The Indiana University (IU) is to: 1.1 Protect Indiana University employees from injuries associated with falls 1.2 Inform Indiana University employees of the hazards
Instructions for assembly and use ZAP telescopic platform ladder Z600
en Instructions for assembly and use ZAP telescopic platform ladder Z600 291361 English Instructions for assembly and use ZAP telescopic platform ladder Contents 1. Information on this manual... 2 1.1
DREW UNIVERSITY FALL PROTECTION PROCEDURE (DRAFT 12/11)
PURPOSE The objective of this policy & guideline is to eliminate the potential for injuries and fatalities to employees and contractors resulting from falls from elevated work areas at Drew University
Harley-Davidson Motor Company
Harley-Davidson Motor Company Standardized Contractor Safety Pre-Qualification Form (SCSPF) Complete and email this form to the appropriate facility by clicking on the location below: Arizona Proving Grounds
Safety Services Guidance. Guidance on: The Provision and Use of Work Equipment Regulations 1998 (PUWER)
Guidance on: The Provision and Use of Work Equipment Regulations 1998 (PUWER) Key word(s) : Work equipment. Using, maintaining and repairing. Information, instruction and supervision. Risk Assessment.
Limited quantities of compressed gases.
173.306 Limited quantities of compressed gases. (a) Limited quantities of compressed gases for which exceptions are permitted as noted by reference to this section in 172.101 of this subchapter are excepted
WT 850 / WT Maximum job performance. Courtesy of Crane.Market
WT 850 / WT 1000 Maximum job performance Revolutionary construction A true space-saver The WT 1000 possesses the special ability of being able to slew its boom system laterally into operating position
QUALITY ASSURANCE SPECIFICATION NONDESTRUCTIVE EXAMINATION PAGE 1 OF 7
QUALITY ASSURANCE SPECIFICATION REVISION: 0 DATE: 08/29/14 NONDESTRUCTIVE EXAMINATION PAGE 1 OF 7 1.0 Purpose The purpose of this specification is to establish the minimum quality assurance requirements
CRANES AND DERRICKS IN CONSTRUCTION. PART 1: INTRODUCTION
CRANES AND DERRICKS IN CONSTRUCTION PART 1: INTRODUCTION Applicability of This Module Use the following General Applicability Checklist to determine whether a rulebook and its sections apply to your operation
User Instructions 1789 Parapet Wall Anchor
User Instructions 1789 Parapet Wall Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee training program as required
Deans, Directors, Heads of Schools and Departments and Research Institute Directors and Managers
Working at Height 1. PURPOSE 1.1 To ensure that any work at height is carried out in accordance with the legal requirements and associated guidance. This includes the use of scaffolds, towers, ladders,
Walking and Working Surfaces: Comprehensive Training
Walking and Working Surfaces: Comprehensive Training PROGRAM SYNOPSIS: To ensure workers are provided with safe working and traveling surfaces, OSHA has developed and recently updated its regulation 29
MEWP - Boom Note: It is recommended that you read the Supporting Information page before you read this factsheet.
MEWP - Boom Note: It is recommended that you read the Supporting Information page before you read this factsheet. Preparation for work (Preparation) Boom-type mobile elevated work platforms, commonly known
Walking/Working Surfaces Plan
South Central College North Mankato/Mankato Campus 1920 Lee Boulevard N. Mankato, MN 56002-1920 Faribault Campus 1225 Third Street SW Faribault, MN 55021-5782 Adoption Date: 03-21-18 Revision Date: Walking/Working
EM Section 12. Control of Hazardous Energy (Lockout/Tagout)
EM 385-1-1 Section 12 Control of Hazardous Energy (Lockout/Tagout) Lockout/Tagout References EM 385-1-1 Section 12 29 CFR 1926.600 (a) (3) i Heavy Equipment 29 CFR 1926.702 (j) (1) Concrete Tools 29 CFR
New OSHA Sweep Auger Enforcement Policy. Presented by: Jim Nolte - Safety Director Wisconsin Agri-Business Association
New OSHA Sweep Auger Enforcement Policy Presented by: Jim Nolte - Safety Director Wisconsin Agri-Business Association Background In 2008 OSHA was asked if an unguarded sweep auger could be operated (energized)
Personal commitments you can live and work by:
Personal commitments you can live and work by: I anticipate possible dangers in any given operation and make every effort to analyze and avoid them before starting work, including immediately communicating
HOW TO PREPARE FOR THE LEVEL A CRANESAFE CERTIFICATION ASSESSMENT
HOW TO PREPARE FOR THE LEVEL A CRANESAFE ASSESSMENT Prepare for your assessment! Our website contains all the information you need for a successful assessment. Our goal is to find you competent on the
Model Safety Program
Model Safety Program DATE: SUBJECT: Safety Procedures for Servicing Single and Multi Piece Rim Wheels. REGULATORY STANDARD: OSHA 29 CFR 1910.177 RESPONSIBILITY: The company Safety Officer is. He/she is
Fall Protection Resource Guide P AGE 1
Fall Protection Resource Guide P AGE 1 As a Home Builder, we do not self-perform any work. This section is a resource guide only and is not intended to put any requirements on the company. All subcontractors,
Fall Protection Program
Fall Protection Program TABLE OF CONTENTS INTRODUCTION... 3 Forward... 3 Objective... 3 Applicability... 3 Responsibilities... 4 Program Enforcement... 5 FALL PROTECTION SELECTION... 6 Site Specific Fall
FALL PROTECTION PLAN INSTRUCTIONS
Sonic Drilling Ltd. FALL PROTECTION PLAN INSTRUCTIONS Each employer must ensure that a fall protection system is used when work is done at a place from which a fall of 3 m (10 ft) or more may occur, or
Sheared Bolts Discovered on JLG Aerial Lift Boom Connections to Platform after Physical Inspection
TN: 3514 Sheared Bolts Discovered on JLG Aerial Lift Boom Connections to Platform after Physical Inspection Priority Descriptor: Yellow /Caution Lesson ID: 2012-BNL-Aerial-0001 Originator: Brookhaven National
OPENINGS AND REINFORCEMENTS 26
ASME BPVC.VIII.1-2015 UG-35.2 UG-36 (4) It is recognized that it is impractical to write requirements to cover the multiplicity of devices used for quick access, or to prevent negligent operation or the
Presented By David F. Coble, MS, CSP. Safety Associates
OSHA Required Training Presented By David F. Coble, MS, CSP Coble, Taylor & Jones Safety Associates www.ctjsafety.com t David F. Coble, MS, CSP 36 years of safety experience including 12 y y p g years
Voluntary clean-up operations at sites recognized by Federal, state, local or other governmental bodies as uncontrolled hazardous waste sites;
All DOL OSHA Advanced Search A to Z Index En Español Contact Us About OSHA OSHA RSS Feeds Print This Page Text Size Home Workers Regulations Enforcement Data & Statistics Training Publications What's New
Doc No: FPP CARDINAL SURVEYS COMPANY. Safety Management System. Initial Revision Date: Version Revision No. 02 FALL PROTECTION
Revision Preparation: Safety Mgr Authority: President Issuing Dept: Safety Page: Page 1 of 10 Purpose The purpose of this program is to provide fall protection procedures to prevent injury to employees
Energy Control Procedures Lockout/Tagout 29 CFR
Energy Control Procedures Lockout/Tagout 29 CFR 1910.147 Paul Schlumper, PE, CSP Georgia Tech Research Institute What is covered? Servicing and maintenance Normal production operations where: Employees
420 LB. CAPACITY. PROTECTIVE SHOULDER CAPS Provide protection and comfort when carrying heavy materials. The Ultimate Full Body Comfort Harnesses
F U L L B O D Y H A R N E S S E S The Ultimate Full Body Comfort Harnesses PROTECTIVE SHOULDER CAPS Provide protection and comfort when carrying heavy materials. ExoFit NEX harnesses are the newest, most
Regulations Respecting Compressed Gas Pressure Vessels
COMPRESSED GAS PRESSURE VESSELS SR 99/70 1 Regulations Respecting Compressed Gas Pressure Vessels Repealed by Chapter B-5.1 Reg 1 (effective January 1, 2007) Formerly Saskatchewan Regulations 99/70 (effective
WORK AT HEIGHT PROCEDURE
WORK AT HEIGHT PROCEDURE Rev No. Reason for Revision Prepared By Reviewed By Approval by Rev 00 Initial Release Navendra Singh Sanjay Kale Shrinivas Katti Rev 01 Standardization of Procedure Anil Jain
Department of Facilities Management. Occupational Health and Safety. Fall Protection Program
Department of Facilities Management Occupational Health and Safety Fall Protection Program October 2016 1 1.0 INTRODUCTION This program has been developed to provide guidance to those managers and supervisors
Sample Written Program. for. Safety Policy
Sample Written Program for Safety Policy 1910, 1926 Safety Policy The following safety policy is provided only as a guide to assist employers and employees in complying with the requirements of 29 CFR
FOCUS 4 HAZARDS ENGLISH Electrocutions Fall Protection Struck-By Caught Inbetween
ENGLISH Electrocutions Fall Protection Struck-By Caught Inbetween Employee general safety Each employee must understand that there is a certain responsibility they must take to ensure their safety on the
HEALTH AND SAFETY PROGRAM 201 HOT TAP PERMIT/FILLET WELD REPAIRS
Page 1 of 15 1.0 PURPOSE 1.1. Axiall, Plaquemine Complex, has developed this Hot Tap Permit Program to eliminate potential accidents, injuries, and to enhance employee protection. 1.2. To provide for the
THE CORPORATION OF THE CITY OF BELLEVILLE BY LAW NUMBER
THE CORPORATION OF THE CITY OF BELLEVILLE BY LAW NUMBER 2006 65 A BY LAW TO PRESCRIBE THE HEIGHT AND DESCRIPTION OF, AND THE MANNER OF ERECTING AND MAINTAINING FENCES AND GATES SURROUNDING PRIVATELY OWNED
Fall Protection / Open Holes & Guardrail
Fall Protection / Open Holes & Guardrail 1. Leading Edges Policy Statement It is GW Communications policy that any worker exposed to a fall 6 or greater, shall be protected from coming into contact with
STEEL TRENCH SHIELDS DW MODELS
STEEL TRENCH SHIELDS DW MODELS 3330 S. SAM HOUSTON PKWY E. HOUSTON, TEXAS 77047 Phone: 713.943.0750 Toll Free: 800.231.6662 Fax: 713. 943.8483 COPYRIGHT, U.S.A., SPEED SHORE CORPORATION, 2009 April 16,
Safety Practice Regulations
Safety Practice Regulations JULY 2017 Name 10028 Copyright BC Hydro 2017. This book and its contents are strictly for work done by or for BC Hydro and all access to its Power System. Any other use, distribution,
MECHANICAL POWER-TRANSMISSION APPARATUS SELF INSPECTION CHECKLIST
Name of School: OPTIONAL INFORMATION Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: MECHANICAL POWER-TRANSMISSION APPARATUS SELF INSPECTION CHECKLIST Guidelines: This checklist
SPEED SHORE MANUFACTURER S TABULATED DATA "MHS" MODELS. STEEL MANHOLE SHIELDS 4 Single Wall 4 Double Wall 4 Double Wall with Cut-Outs
SPEED SHORE MANUFACTURER S TABULATED DATA "MHS" MODELS STEEL MANHOLE SHIELDS 4 Single Wall 4 Double Wall 4 Double Wall with Cut-Outs January 01, 2005 3330 S. SAM HOUSTON PKWY E. HOUSTON, TEXAS 77047 Tel:
FALL PROTECTION SAFETY PROGRAM
FALL PROTECTION SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.66-29 CFR 1910.128, 129, 130, 131, (Proposed) - 29 CFR 1926.104-29 CFR 1926.500-503 BASIS: Approximately 300,000 disabling injuries
American National Standards Institute, ANSI Z359 Fall Protection Code Update
NAVFAC SOUTHEAST American National Standards Institute, ANSI Z359 Fall Protection Code Update John Davis, SSM Prepared by: Basil Tominna, P.E. September 2010 29 June 2012 Introduction ANSI approved several
Regulated Oil and Gas Companies under National Energy Board Jurisdiction
File 185-A000-41 8 August 2003 Regulated Oil and Gas Companies under National Energy Board Jurisdiction Dear Sir / Madam: Guidance Notes for Pressure Equipment under National Energy Board Jurisdiction
FALL PROTECTION
115500 FALL PROTECTION PART 1 GENERAL 1.01 General A. Cornell University seeks to prevent exposures to fall hazards whenever possible and protect personnel that may be exposed to fall hazards. Therefore,
MODULAR ALUMINUM PANEL SHIELDS MAPS
MODULAR ALUMINUM PANEL SHIELDS MAPS 3330 S. SAM HOUSTON PKWY E. HOUSTON, TEXAS 77047 Phone: 713.943.0750 Toll Free: 800.231.6662 Fax: 713. 943.8483 April 16, 2009 MODULAR ALUMINUM PANEL SHIELDS Page 2
Chapter 2 Rigging. Cutting Wire Rope. Anchoring Wire Rope to Drum. Winding Wire Rope Onto Drum
Chapter 2 Rigging Cutting Wire Rope The wire rope must be tightly seized on both sides of the point where the wire rope will be cut, as shown in Figure 2-1. Seize the wire rope with either seizing wire
COOPER POWER SERIES. D-73P3 bypass switches installation instructions. Switches MN008005EN. Effective April 2016 Supersedes S June 2013
Switches MN008005EN Effective April 2016 Supersedes S328-120-1 June 2013 D-73P3 bypass switches installation instructions COOPER POWER SERIES DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY The information,
POWER DELIVERY. Contractor Health & Safety General Terms and Conditions. Appendix B Personal Protective Equipment
Personal Protective Equipment ( PPE ): All PPE worn on IPL job sites must have ANSI and/or approval ratings. Hard hats and safety glasses with side shields (including prescription eyewear) shall be worn
Authority for 1910 Subpart I - 1910 Subpart I Page 1 of 1 nmlkj All DOL nmlkji OSHA Advanced Search OSHA Home Occupational Safety & Health Administration A to Z Index En Español Contact Us What's New About
STANDARD FOR CONTROL VALVE SEAT LEAKAGE
11-3 STANDARD FOR CONTROL VALVE SEAT LEAKAGE 1. PURPOSE 1.1 This standard establishes a series of seat leakage classes for control valves and defines the test procedures. 2. SCOPE & LIMITATIONS 2.1 Selection
Boat Hoist Operations Code of Practice and Guidance COP2
Boat Hoist Operations Code of Practice and Guidance COP2 Edition 2 January 2016 Contents Introduction... 2 Access... 2 Liability... 2 Notification of boat hoisting at La Collette yacht basin... 3 Responsibilities
ARC FLASH PROTECTION AT HEIGHTS
ARC FLASH PROTECTION AT HEIGHTS Arc Rated Fall Protection FallTech has you covered with Arc Rated products for the four components of a Personal Fall Arrest System (PFAS). Anchorage Connector When working
STEEL TRENCH SHIELDS TUFF-LITE MODELS
STEEL TRENCH SHIELDS TUFF-LITE MODELS 3330 S. SAM HOUSTON PKWY E. HOUSTON, TEXAS 77047 Phone: 713.943.0750 Toll Free: 800.231.6662 Fax: 713. 943.8483 April 16, 2009 TRENCH SHIELDS TUFF-LITE TM Page 2 of
escalino The convenient stair climber Conquer stairs easily and safely
The convenient stair climber escalino Conquer stairs easily and safely www.aat-online.de Be it a handicap or an illness, stairs restrict your personal mobility considerably. With the escalino you can enjoy
MSC Guidelines for Pressure Vessels
References: a. 46 CFR Part 54 Pressure Vessels S. T. Brady, CDR, Chief, Engineering Division b. ASME Boiler and Pressure Vessel Code (BPVC), Section VIII, Division 1, (1998 Edition) c. Navigation and Inspection
Hot Work Program. University of Wisconsin-Platteville Reviewed 4/2016
Hot Work Program University of Wisconsin-Platteville Reviewed 4/2016 The purpose of the Hot Work Program is to establish safety procedures for employees, contractors, and subcontractors engaging in any
PRODUCT PROFILE 2017
PRODUCT PROFILE 2017 Column Climber is a division of Nascent Corporation COLUMN CLAW Column Claw (flange widths to 14 ; flange thicknesses to 1-7/8 ) Column Claw is vertically-sliding and fall-activated
September 27, DOE-RL-92-36, Hanford Site Hoisting and Rigging Manual. Wire Rope. Page 1 CONTENTS
Page 1 CONTENTS 8.0 WIRE ROPE...2 8.1 SCOPE...2 8.2 GENERAL REQUIREMENTS...2 8.2.1 Design Factors For s... 2 8.2.2 Rotation-Resistant Rope...3 8.2.3 Requirement for Independent Core...3 8.3 INSPECTION
1. Section Summary for loose climbing equipment provided by Owner. 2. Section "Cast in Place Concrete"
SECTION 131200 CLIMBING WALLS PART 1 - GENERAL 1.1 SUMMARY A. Work included: 1. Provide seamless textured substrate, panel-formed interior climbing wall system with internal structural support system,
FALL PROTECTION (SAF-SPI-06)
1. PURPOSE To describe the Ontario Operations standard methods for preventing serious injury resulting from fall from heights and to provide a Standard for Fall Protection to safeguard employees who work
GROVE MODEL RT58D - 20 TON CAPACITY
LIFTING CHARTS - Rough Terrain Cranes GROVE MODEL - 20 TON CAPACITY WEIGHT REDUCTIONS FOR LOAD HANDLING DEVICES 23 JIB with 28-70 BOOM * Stowed - 381 lbs. * Erected - 1,950 lbs. 23-38 TELE. JIB with 28-70
VERSION 1.0 FEBRUARY 1, 2017 FALL PROTECTION AND ELEVATED WORK UNC CHARLOTTE 9201 UNIVERSITY CITY BLVD., CHARLOTTE, NC 28223
VERSION 1.0 FEBRUARY 1, 2017 FALL PROTECTION AND ELEVATED WORK UNC CHARLOTTE 9201 UNIVERSITY CITY BLVD., CHARLOTTE, NC 28223 Table of Contents I. Purpose... 3 II. Scope... 3 III. Program Responsibilities...
WBM Installation Manual KAT Master Hitch
WBM Installation Manual KAT Master Hitch General Information This section provides general information and recommendations required prior to installing, operating or maintaining your KAT Master Hitch.
Equipment Operation Procedures
Procedures Purpose It is the policy of this company to permit only trained and authorized personnel to operate construction equipment. These procedures are applicable to both daily operators, and those
Walking-Working Surfaces Fall Protection Program
Purpose Walking-Working Surfaces Fall Protection Program The purpose of this program is to provide procedures to eliminate, prevent, and control hazards from falls from heights. Scope This program is applicable
Competent Person - Fall Protection Presented by Turner Safety- your instructor is Steve Turner
Competent Person - Fall Protection Presented by Turner Safety- your instructor is Steve Turner 1 Falls in Construction Falls are the leading cause of deaths in the construction industry. Most fatalities
ModelsEZU-15 & EZU-15-R. BISHAMON INDUSTRIES CORPORATION 5651 East Francis Street Ontario, California 91761, USA (909) (800)
UP P n e u m a t i c ModelsEZU-15 & EZU-15-R BISHAMON INDUSTRIES CORPORATION 5651 East Francis Street Ontario, California 91761, USA (909) 390-0055 (800) 231-3187 Table of Contents GETTING STARTED......................................
WORKING AT HEIGHT RESOURCE BOOKLET. Working at Height 1
WORKING AT HEIGHT RESOURCE BOOKLET Working at Height 1 Falls constantly top the HSENI Construction Group Statistics as the biggest cause of major injuries. The Construction Employers Federation Health
Safety System Installation Guide for ARE Wind Poles
Safety System Installation Guide for ARE Wind Poles V. 1 May 2011 ** Climbing pegs and ladder should be installed before the pole is erected.** A. Install climbing pegs Install climbing pegs (bolt set)