FALL FROM LADDER INCIDENT
|
|
- Ruby Barber
- 6 years ago
- Views:
Transcription
1 FALL FROM LADDER INCIDENT DRILLSAFE MELBOURNE 02 DECEMBER, 2010 Presenter: Russell Telford Rig175 HR /HSE Supervisor
2 WORKING AT HEIGHT EXPECTATIONS WHEN WORKING AT HEIGHTS THE EXPECTATION IS NOBODY FALLS AND TO BRING ABOUT A SIGNIFICANT REDUCTION IN RISK ASSOCIATED WITH WORKING AT HEIGHT. THIS CAN BE ACHIEVED WITH PROPER PLANNING APPROPRIATE TRAINING ESTABLISHING PEOPLES ROLES AND RESPONSIBILITIES CORRECT EQUIPMENT SELECTION: CERTIFICATION, INSPECTION AND MAINTENANCE. SAFE BEHAVIORS PARTNERSHIP APPROACH EMERGENCY RESPONSE PLAN 2
3 THE INCIDENT OVERVIEW THE DRILL CREW WERE PREPARING TO RUN THE WEARBUSHING ON A STAND OF DRILL PIPE. THE FLOORMAN ASCENDED THE MAST TO RACK BACK A STAND OF DRILL PIPE AT THE CONCLUSION OF SETTING THE WEAR BUSHING. AT THE COMPLETION OF RACKING BACK THE STAND OF DRILL PIPE THE FLOORMAN DESCENDED THE MAST TO ATTEND A JSA FOR THE NEXT OPERATION. DURING THE DESCENT OF THE MAST THE FLOORMAN FELL FROM THE MAST LADDER APPROXIMATLY 14 FEET TO THE RIG FLOOR. 3
4 R175 RIG FLOOR LAYOUT AT TIME OF INCIDENT Floorman Driller Roust Floorman Roust V-Door 4
5 THE INVESTIGATION THE INVESTIGATION FOUND THAT DURING THE FLOORMANS DESCENT THE LAD-SAF BRAKING DEVICE (PRIMARY FALL PROTECTION) ENGAGED AT APPROXIMATELY 14FT FROM THE RIG FLOOR. THE FLOORMAN TRIED TO DISENGAGE THE BRAKE BY STEPPING UP ONE RUNG AND HOLDING HIS WEIGHT WITH HIS LEFT FOOT WHILE USING HIS RIGHT HAND TO DISENGAGE THE BRAKE. AT THIS POINT THE FLOORMAN LOST THREE POINT CONTACT WITH THE LADDER. THE FLOORMAN ONLY HAD HIS LEFT HAND AND LEFT FOOT IN CONTACT WITH THE LADDER. 5
6 THE INVESTIGATION THE FLOORMANS LEFT FOOT SLIPPED ON THE LADDER RUNG SIDEWAYS AND HIS LEG WENT THROUGH THE LADDER CAUSING HIM TO LOSE HIS BALANCE. THIS CAUSED THE FLOORMAN TO GRAB THE BRAKING DEVICE AND THE LAD-SAF CABLE TOGETHER, THEREFORE DISABLING THE BRAKING DEVICE. 6
7 THE INVESTIGATION APPROXIMATELY 6FT FROM THE RIG FLOOR THE LAD-SAF BRAKING DEVICE ENGAGED. DUE TO THE FLOORMANS MOMENTUM THE KARABINER THAT CONNECTED HIS HARNESS TO THE LAD-SAF SYSTEM ELONGATED AND OPENED UP ALLOWING THE FLOORMAN TO FALL TO THE RIG FLOOR. New Damaged 7
8 THE INVESTIGATION NO SECONDARY FALL PROTECTION WAS USED BY THE FLOORMAN. ie: INERTIA REEL AS REQUIRED BY POLICY AND THIS WAS IN PLACE FOR USE WHEN ASCENDING AND DESCENDING THE MAST. THE KARABINER SCREW GATE WAS FOUND TO BE IN THE UNLOCKED POSITION WHICH WAS CONFIRMED BY A CERTIFIED THIRD PARTY AUTHORITY. THIS EFFECTED THE INTEGRITY AND THE EFFICIENCY OF THE KARABINER. THUS ALLOWING THE KARABINER TO ELONGATE AND OPEN UP. THE KARIBINERS SWL WHEN IN THE LOCKED POSITION IS 2549 KG, WHEN THE KARABINER IS IN THE UNLOCKED POSITION ITS LOSES 2/3 S OF ITS INTEGRITY. 8
9 INJURED FLOORMANS STATUS AS A RESULT OF THE FALL THE FLOORMAN SUSTAINED A FRACTURED LEFT FIBULA 2 INCHES ABOVE THE ANKLE AND INJURED HIS L1 & L2 VERTEBRA. 9
10 DIRECT CAUSES THE FLOORMAN LOST THREE POINT CONTACT WITH THE LADDER WHILE TRYING TO DISENGAGE THE LAD-SAF BRAKING DEVICE. THE SECONDARY FALL ARREST SYSTEM (INERTIA REEL) THAT WAS INPLACE WAS NOT USED AS PER COMPANY POLICY. THE KARABINER SCREW GATE WAS NOT PLACED IN THE LOCKED POSITION. 10
11 ACTIONS TO PREVENT RECURRENCE A SAFETY STANDDOWN WAS HELD AND ACCESS TO THE MAST SUSPENDED UNTIL FURTHER RISK ASSESSMENT AND JOB SAFETY ANALYSIS WERE CONDUCTED. THE HEIGHT SAFETY EQUIPMENT WAS CHECKED AND VERIFIED TO BE IN GOOD OPERATING CONDITION BY A CERTIFIED THIRD PARTY AUTHORITY. THE CREWS WERE TRAINED ON BASIC LADDER TECHNIQUES. TASK SPECIFIC JSA S AND BUDDY CHECKLISTS WERE DEVELOPED FOR ASCENDING / DESCENDING THE MAST. THIS ENSURES PERSONNEL ACCESSING THE MAST HAVE A BUDDY TO ASSIST WITH THE APPROPRIATE P.P.E. AND GIVE VERFICATION OF CORRECT FITMENT. ADDITIONAL SIGNAGE WAS PLACED AT THE ACCESS POINTS OF ALL THE MAST LADDERS. 11
12 ACTIONS TO PREVENT RECURRENCE 12
13 ACTIONS TO PREVENT RECURRENCE 13
14 VERIFICATION ARE OUR WORKING AT HEIGHTS EXPECTATIONS UNDERSTOOD AND REINFORCED ON A REGULAR BASIS? WHEN WERE CREW MEMBERS LAST TRAINED? HAVE THE RIG CREWS RECEIVED REFRESHER TRAINING? DO CREW MEMBERS UNDERSTAND CORRECT USE OF FALL PROTECTION SYSTEMS? WHAT FALL PROTECTION SYSTEMS ARE AVAILABLE / REQUIRED FOR EACH ASCENDING/DESCENDING LADDER? 14
15 VERIFICATION WHAT PROCESSES ARE BEING USED FOR EQUIPMENT SELECTION, CERTIFICATION, INSPECTION, MAINTENANCE? IS THE WORKING-AT-HEIGHTS OPERATIONS CHECKLIST BEING USED? FOR WHAT OPERATIONS/ACTIVITIES? ARE PROCESSES DIFFERENT FOR EXPERIENCED VS INEXPERIENCED CREW MEMBERS? DO JSA S FOR ALL ACTIVITIES COVER DIFFERENT WORKING-AT-HEIGHTS HAZARDS? 15
Dropped Sheave Saddle Bracket
Dropped Sheave Saddle Bracket Dropped Sheave Bracket - Chronology Date and Time of incident Location of Incident Severity 28 th August 2007 @ 00:15 hrs RIG 100 Work floor High Potential Chronology 28th
More information22.30 hrs. DrillSafe Forum Presentations - Perth Western Australia 5 th Mar 09
Near Miss Dropped 13 3/8 inch Casing 6 th November 2008 22.30 hrs What Happened A joint of 13 3/8 inch casing came out of the single joint elevator at floor level and travelled down the vdoor, along the
More informationSECURITY AND CONFIDENCE AT HEIGHT
Detachable Cable Sleeve SECURITY AND CONFIDENCE AT HEIGHT THE ULTIMATE IN FALL PROTECTION THE DANGERS OF WORKING AT HEIGHT Every day, workers around the world climb ladders to great heights to get their
More informationTechnical Briefing Note
Technical Briefing Note Subject Date Issued Revision Glossary of Terms 14th Nov 2017 Rev 3 The purpose of this Technical Briefing Note is to provide a glossary of terms commonly used in fall injury prevention
More informationInstallation Drawings & Instructions Fall Protection Systems
ISO 9001 Registered Installation Drawings & Instructions Fall Protection Systems Attach the Cougar Slider only at this Sternum Connection Point CSA Z259.2.1-98 & ANSI Z359.1-M1992 [Canada & USA] Revision
More informationSAFE PRACTICES FOR ROPE ACCESS WORK
SAFE PRACTICES FOR ROPE ACCESS WORK Society of Professional Rope Access Technicians 994 Old Eagle School Road, Suite 1019 Wayne, PA 19087 USA (610)971-4850 www.sprat.org info@sprat.org Version 17A Board
More informationSWMS No 001 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 5
Samark North Qld Pty Ltd SWMS Manual SWMS No 00 Samark North Qld Pty Ltd ABN : 99 082 98 87 Electrical Contractors License C372 Page 2 of Safe Work Method Statement Title: SWMS:00 USING PORTABLE LADDERS
More information11.4 FALL-ARREST SYSTEM AND EQUIPMENT CHECKLIST (Must answer yes to all applicable questions)
11.4 FALL-ARREST SYSTEM AND EQUIPMENT CHECKLIST (Must answer yes to all applicable questions) This checklist shall be completed either by the Competent Person or a person trained and designated by the
More informationTechnical Rescuer Rope Rescue Level I NFPA 1006
Standard Area: 6.1.3 General Skill Requirement 6.1.3 General Skill Requirements JPR #RRI-1 Candidate: : Candidate #: STANDARD: 6.1.3 Level I, 2013 Edition TASK: Construct a multiple-point anchor system,
More informationTable of Contents. Chapter 1: Health, Safety and Environment Programs. Chapter 2: General Guidelines and Health Control
IADC Health, Safety and Environmental Reference Guide Table of Contents Chapter 1: Health, Safety and Environment Programs Safety Policy Statement... 1 HSE Meetings... 1 Safety Inspections and Logbooks...
More informationRescue Technician: Rope Rescue I
Rescue Technician: Rope Rescue I Skill Sheet Package Based on NFPA 1006: Standard for Technical Rescue Professional Qualifications, 2013 Edition. Alabama Fire College August 2016 REVISED 02/10/2017 Alabama
More informationFALL PROTECTION / ELEVATED WORK
SEPTEMBER CORE REFRESHER HSE TOOL BOX FALL PROTECTION / ELEVATED WORK FALL PROTECTION Falls from elevations are one of the most common causes of death in this industry. OSHA requires fall protection when
More informationSafety is a priority at Vault Pipelines.
Safety is a priority at Vault Pipelines. At Vault Pipelines we believe that every incident is preventable and that every task can be completed safely and efficiently. We will achieve this through our cultural
More informationOverview. Identify fall hazardous areas Describing potential fall hazards How appropriate portable and extension ladders are used
FALL PROTECTION Overview Identify fall hazardous areas Describing potential fall hazards How appropriate portable and extension ladders are used Fall Protection All situations that expose personnel to
More informationPOLMAK SONDAJ SANAYII A.S. HEALTH, SAFETY, AND ENVIRONMENTAL POLICY
POLMAK SONDAJ SANAYII A.S. HEALTH, SAFETY, AND ENVIRONMENTAL POLICY 2 POLMAK GROUP S HSE POLICY Objective The aim of this Manual is to assist our drilling and exploration company POLMAK SONDAJ SANAYII
More information2. Ensure that the leg strap buckles are not obstructed and operate smoothly.
CLIMBING EQUIPMENT NOTE. This equipment is for safety purposes only. It is not to be used as a working harness to support the wearer while working aloft. The equipment has three components; 1. Harness
More informationA Previously Unidentified Failure Mode for Ladder-Climbing Fall-Protection Systems
Session No. 716 A Previously Unidentified Failure Mode for Ladder-Climbing Fall-Protection Systems Introduction Steve Arndt, Ph.D. Principal Engineer Exponent Failure Analysis Associates Chicago, Illinois
More informationSG19:17 NASC. A Guide to Formulating a Rescue Plan 1. INTRODUCTION
SG19:17 A Guide to Formulating a Rescue Plan 1. INTRODUCTION The legal requirement for rescue is specified in the Work at Height Regulations 2005 and require every employer in selecting work equipment
More informationFOR. Society of Professional Rope Access Technicians 994 Old Eagle School Road, Suite 1019 Wayne, PA
SAFE PRACTICES FOR ROPE ACCESS WORK Society of Professional Rope Access Technicians 994 Old Eagle School Road, Suite 1019 Wayne, PA 19087-1866 www.sprat.org 2007 Society of Professional Rope Access Technicians
More informationFALL PROTECTION. Leader s Guide. Marcom Group Ltd.
1818 FALL PROTECTION Leader s Guide Marcom Group Ltd. Structure and Organization Information in this program is presented in a definite order, so that employees will see the relationships between the various
More informationCWA Work-at-Height Certification Assessment Criteria Competent Climbing Wall Worker
Course Date(s): Course Location: Provider(s): Candidate s Name: Candidate s Company: Candidate s Personal Contact Information (complete personal mailing address, mobile phone and personal email address):
More informationDoc No: FPP CARDINAL SURVEYS COMPANY. Safety Management System. Initial Revision Date: Version Revision No. 02 FALL PROTECTION
Revision Preparation: Safety Mgr Authority: President Issuing Dept: Safety Page: Page 1 of 10 Purpose The purpose of this program is to provide fall protection procedures to prevent injury to employees
More informationRIDE Inc. Rigscape Drilling Rig Procedures
2016 RIDE Inc. Rigscape Drilling Rig Procedures Special Instructions/Conditions of Use Reading user procedure manual prior to use is essential Only persons that have been deemed competent in the operation
More information6. Each mitigation was verified and individually documented
CHESM/MSW Field Verification Instructions: All information in sections A, B and C must be completed. Information in section B related to subcontractors should be obtained from the work crew if possible.
More informationTransfer Chain (SA-1002) & Adjustable I-Beam Clamp (SA-1039 or SA-1040) Operating Instructions
Transfer Chain (SA-1002) & Adjustable I-Beam Clamp (SA-1039 or SA-1040) Operating Instructions SPIDER Page 1 of 8 702127 Rev A Using Transfer Chain with Adjustable I-Beam Clamp Safety Notes Do not use
More informationSEVERE INJURY WITH HAND AMPUTATION AND SKULL FRACTURE
HSE Bulletin Page no.1 SEVERE INJURY WITH HAND AMPUTATION AND SKULL FRACTURE Type of accident: Data of accident: Job position: Type of activity: Activity performed: Lost Time Injury March, 14 th 2003 Motorman
More informationCONTRACTOR WHS HAZARD STANDARD CONFINED SPACE EXTERNAL USE ONLY
CONTRACTOR WHS HAZARD STANDARD CONFINED SPACE EXTERNAL USE ONLY Principles in the Optus Contractor WHS management process CONTRACTOR MANAGEMENT STAGES PRINCIPLES THIS STANDARD REQUISITION Requisition WHS
More informationCompliance Is the First Step on the Safety Ladder Understanding the final walking-working surface rule from OSHA and how Honeywell ladder solutions
Compliance Is the First Step on the Safety Ladder Understanding the final walking-working surface rule from OSHA and how Honeywell ladder solutions keep you protected OSHA Walking-Working Surface Rule
More informationProvide initial response at rope rescue incidents
Page 1 of 5 Provide initial response at rope rescue incidents Level 4 Credits 6 Purpose This unit standard is for people who are required to respond to a rope rescue incident. People credited with this
More informationOperating and Safety Instructions. Sectional doors
Operating and Safety Instructions Sectional doors Index Index General Information Warnings and Safety Instructions Inspection / Maintenance Attention in case of rope rupture or spring fracture Operation
More informationFALL PROTECTION SAFETY PROGRAM
FALL PROTECTION SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.66-29 CFR 1910.128, 129, 130, 131, (Proposed) - 29 CFR 1926.104-29 CFR 1926.500-503 BASIS: Approximately 300,000 disabling injuries
More informationRIDE Inc. Rigscape Service Rig Procedures
2016 RIDE Inc. Rigscape Service Rig Procedures Special Instructions/Conditions of Use Reading user procedure manual prior to use is essential Only persons that have been deemed competent in the operation
More informationInstallation & User Manual
Installation & User Manual September 2017 INTRODUCTION General Information The fall protection system on this project has been installed to reduce the risk experienced by the users when carrying out light
More informationFall Protection and Elevated Work
Program No: SP-010 Page 1 1.0 PURPOSE AND INTRODUCTION Fall Protection and Elevated Work To establish fall protection safety procedures for Pitt County Schools employees engaged in any of the following
More informationA GUIDE TO BUYING FALL ARREST EQUIPMENT. uk.rs-online.com (UK customers) (International customers)
A GUIDE TO BUYING FALL ARREST EQUIPMENT (UK customers) www.rs-components.com (International customers) INTRODUCTION In a world of evolving legislation employers in the EU have had a legal responsibility
More informationUser Instruction Manual Tripod Anchorage Connectors
User Instruction Manual Tripod Anchorage Connectors This manual is intended to meet the Manufacturer's Instructions as required by ANSI Z359.1 and ANSI A10.14, and should be used as part of an employee
More informationWINDMILL (pre-start) HAZARD INSPECTION CHECKLIST
Windmill Hazard Inspection Checklist WINDMILL (pre-start) HAZARD INSPECTION CHECKLIST Authorised by: LOCATION OF INSPECTION...... Inspected By (1)........... (2)..... PRINT PRINT Signature (1):. (2)....
More informationIRATA. Levels, 1, 2, or 3 5 days training + 1 assessment day (Includes Examination Fees + IRATA Registration)
AIMED AT Employees of companies and individuals who wish to obtain / maintain an international accreditation for rope access and work positioning. Levels, 1, 2, or 3 5 days training + 1 assessment day
More information(MSW) Process Overview. Introduction Chevron Corporation. All rights reserved.
SiteSafe Managing Safe User Work Training (MSW) Process Overview Introduction 2009 Chevron Corporation. All rights reserved. Operational Excellence Management System 2009 Chevron Corporation. All rights
More informationValidity Date Reg No 10 years HMSS-329. Unit Reviewer Approver Version HSE&Q Anne-Louise Thäng Helén Axelsson 13
INSTRUCTIONS 1(5) WORKING AT HEIGHT 1 General All work must be planned, arranged and carried out so that accidents caused by falling or falling objects are prevented (The Work Environment Act and its regulations).
More informationProduct Numbers & Ordering Information
United Kingdom Product Family Söll Vi-Go Vertical Cable System Söll Vi-Go Ladder Climbing Safety Systems provide the ultimate in safety with continuous fall protection when climbing fixed ladders: remarkably
More information1 AIM 2 4 REASONS FOR INCLUSION 3 6 PLANT AND EQUIPMENT REQUIREMENTS 4 7 SYSTEM AND PROCEDURAL REQUIREMENTS 4 8 PEOPLE REQUIREMENTS 6
CONTENTS PAGE 1 AIM 2 2 APPLICATION 2 3 DEFINITIONS 2 4 REASONS FOR INCLUSION 3 5 REQUIREMENTS 3 6 PLANT AND EQUIPMENT REQUIREMENTS 4 7 SYSTEM AND PROCEDURAL REQUIREMENTS 4 8 PEOPLE REQUIREMENTS 6 APPENDIX
More informationWorking at Height. Policy and Procedures. Author: Beth Webster Assistant Safety Advisor. On behalf of School Safety Committee.
Working at Height Policy and Procedures Author: Beth Webster Assistant Safety Advisor Authorised by: Issued by: John Stephenson Safety Office On behalf of School Safety Committee Review Date: NO LATER
More informationEliminating Dropped Objects at the Worksite
Eliminating Dropped Objects at the Worksite Allen Smith, DROPS GLOBAL Eliminating Dropped Objects at the Worksite Allen Smith, DROPS GLOBAL ABOUT DROPS: dropsonline.org Oil & Gas Industry Workgroup focused
More informationP+P Product Code 90015/20
v2 12/08 P+P ANTHRON SELF RESCUE SYSTEM USER INSTRUCTIONS P+P Product Code 90015/20 This manual does not constitute suitable and sufficient training in the use of this rescue equipment. Contact P+P for
More informationRope Grab Operation & Maintenance Manual
S A F E T Y A T T H E H I G H E S T L E V E L Rope Grab Operation & Maintenance Manual Rope Grab Operation (14mm) The rope grab has to be opened to position the rope correctly. Open the rope grab device
More informationUSER S MANUAL V3.0. MULTI-PURPOSE DEVICE Pulley Descent Control Belay
USER S MANUAL V3.0 MULTI-PURPOSE DEVICE Pulley Descent Control Belay MULTI-PURPOSE DEVICE Pulley Descent Control Belay Thank you for selecting the CMC MPD for your technical rope rescue systems. Truly
More information1. Objective of the initiative To ensure that all employees and subcontractors are aware of the risks associated with working at height.
Safety Initiative 02 Working at Height May 2011 CONTENTS 1. Objective of the initiative 2. Overview. 3. Implementation 4. Duties 5. Hierarchy of Controls 6. Workplace Inspections 7. Fragile Surfaces 8.
More informationUSER S MANUAL MULTI-PURPOSE DEVICE. Pulley l Descent Control l Belay V2.3. cmcrescue.com (800) Goleta, CA USA
Pulley l Descent Control l Belay MULTI-PURPOSE DEVICE V2.3 USER S MANUAL 6740 Cortona Drive Goleta, CA 93117 USA support@cmcrescue.com (800) 235-5741 cmcrescue.com Control No. MAN - 3330X0 Rev 00 MULTI-PURPOSE
More informationThe purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field.
Purpose The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field. Fall Protection and Prevention JELD-WEN Field Employees
More informationNew Mexico Institute of Mining & Technology. Fall Protection Program
New Mexico Institute of Mining & Technology Fall Protection Program REGULATORY STANDARDS: OSHA - 29 CFR 1910.66 29 CFR 1910.128, 129, 130, 131, (Proposed) 29 CFR 1926.104 29 CFR 1926.500 BASIS: Approximately
More informationWalking-Working Surfaces and Fall Protection Standards Update. OSHA General Industry
Walking-Working Surfaces and Fall Protection Standards Update OSHA General Industry Background Slips, trips, and falls account for a majority of all general industry injury incidents. Caused 849 workplace
More informationUSER S MANUAL V2.2. MULTI-PURPOSE DEVICE Pulley Descent Control Belay
USER S MANUAL V2.2 MULTI-PURPOSE DEVICE Pulley Descent Control Belay 6740 Cortona Drive Goleta, CA 93117 USA support@cmcrescue.com (800) 235-5741 cmcrescue.com 3330X0.00.101413 WARNING MULTI-PURPOSE DEVICE
More informationUser Instructions. Mobile Ladders with Platform to BS EN 131-7:2013
User Instructions Mobile Ladders with Platform to BS EN 131-7:2013 User Instructions for Mobile Ladders with Platform to BS EN 131-7:2013 All mobile steps are built to the highest engineering standards
More informationApplying Construction Fall Protection Concepts to General Industry
Applying Construction Fall Protection Concepts to General Industry Applying Construction Fall Protection Concepts to General Industry Michael Tesmer, CSP and David Jewell, CSP Conney Safety Products This
More informationSafewaze FS983 Cable Safety Climb System Ladder Mount Instructions
Safewaze FS983 Cable Safety Climb System Ladder Mount Instructions Ladder Mount Cable Safe Climb System B) Head Assembly with Cable A) Upright Mast C) Cable Standoff E) Cable Clamps D) Base Anchor Bracket
More informationSAFE WORK METHOD STATEMENT (SWMS) All Trades Abseiling ABN: Ph:
PCBU: ALL TRADES ABSEILING ABN: 42 137 576 035 PO Box 774 NEWPORT NSW 2106 LIC: 123517C P: 0412 227 578 Principal Contractor (PC): Date SWMS provided to PC: Work activity: Workplace location: High risk
More informationDeveloped by Firefighter Ty Drage January NFPA 1670 Standard on Operations and Training for Technical Search and Rescue Incidents
Q UICK A CCESS K IT (1.1) Developed by Firefighter Ty Drage January 2011 NFPA 1670 Standard on Operations and Training for Technical Search and Rescue Incidents T ASK S KILL DESCRIPTION AND DETAIL Every
More informationGUIDE 2002 HEALTH AND SAFETY FOR ARTIFICIAL CLIMBING STRUCTURES AND OPERATIONS FOR DESIGNERS, MANUFACTURES, SUPPLIERS, OPERATORS AND USERS
HEALTH AND SAFETY FOR ARTIFICIAL CLIMBING STRUCTURES AND OPERATIONS FOR DESIGNERS, MANUFACTURES, SUPPLIERS, OPERATORS AND USERS GUIDE 2002 WorkCover NSW Health and Safety Guide WorkCover Watching out for
More informationGEMTOR. ... when your life is on the line OWNER'S MANUAL. FLW Series Self-Retracting Lanyard/Fall Limiter
GEMTOR TM... when your life is on the line OWNER'S MANUAL FLW Series Self-Retracting Lanyard/Fall Limiter Installation, Operating, Inspection and Maintenance Instructions Warning You must read and fully
More informationZIGZAG Experience. Important / remember. Failure to heed any of these warnings may result in severe injury or death.
A. Childeric / Copalme ZIGZAG Experience This "Product Experience" document is a supplement to the Instructions For Use, which provides feedback from field experience and tips for using your product It
More informationSecurity and confidence at height.
A Security and confidence at height. Vertical Systems DISTRIBUTED BY M DBI-SALA Vertical Systems are designed to complement your ability to work while meeting all applicable OSHA and ANSI standards. Vertical
More informationUSER INSTALLATION & INSTRUCTION MANUAL Manual #4.9XX.0000.R00
ISO 9001 Registered USER INSTALLATION & INSTRUCTION MANUAL Manual #4.9XX.0000.R00 Rail Fall Protection System Ladder and Titan Towers Installations CSA Z259.2.1-98 Revision Date: April 29, 2011 1 Table
More informationHEALTH & SAFETY ARRANGEMENTS FOR MANAGEMENT OF WORK AT HEIGHT
HEALTH & SAFETY ARRANGEMENTS FOR MANAGEMENT OF WORK AT HEIGHT INTRODUCTION Cwmni CYNNAL recognises that accidents can arise from working at height. Falls from height can be a cause of injury and absence
More informationNo communication between the injured technician and his co-worker, and no visual line of site from the anchor area to the worksite.
IRATA Safety Bulletin Description Contributing factors Control measures SB 1: Non-IRATA incident. Technician fell approximately 30 metres after connecting to ropes whilst on a balcony halfway down a highrise
More informationHarness Kit KIT 1. Colour: Size: Add date to any comments. Inform OIC or DOIC of any issues arising immediately.
Harness Kit KIT 1 Colour: Size: MODEL : NAVAHO BOD CROLL FAST HARNESS The results of this PPE inspection are provided to you subject to the condition that the components to be inspected do not come into
More informationFALL PROTECTION COMPARISON BETWEEN VARIOUS OSHA STANDARDS, NAVY and EM 385 (2008) REQUIREMENTS
Requirements FALL PROTECTION COMPARISON BETWEEN VARIOUS OSHA STANDARDS, NAVY and EM 385 (2008) REQUIREMENTS Navy FP Chapter 13 of OPNAVINST 5100.23G (2005) and Fall Protection Guide for Ashore Facilities
More informationMR-051 ROOF ACCESS PERMIT
Instruction 1 State the job Details. Date: Site Name: Site Supervisor: Number of workers: Work description: Blocks being accessed: Existing weather conditions: Instruction 2 State and verify competency/
More informationFall Protection Plan. Chinook Drilling 8/10/2012
2012 Fall Protection Plan Chinook Drilling 8/10/2012 Written by: ST, AO Checked by: Approved by: A.O 2 3 Table of Contents 179.0 Fall Protection Plan... 9 180.0 Slips, Trips and Falls from The Same Level...
More informationLAD-SAF LAD-SAF VERTICAL SAFETY SYSTEM THE ULTIMATE IN FALL PROTECTION
LAD-SAF VERTICAL SAFETY SYSTEM THE ULTIMATE IN FALL PROTECTION CONTENTS Product Overview 2 Working Safely at Height 2 Features & Benefits 3 Lad-Saf X2 Detachable Cable Traveller 4-5 Typical System Configurations
More informationGeneral Risk Assessment for Climbing, Bouldering and Abseiling
General Risk Assessment for Climbing, Bouldering and Abseiling Activity: Climbing, Abseil and Bouldering Activity Session What are the hazards? Who at risk? What are the risks? Ankle injuries, head injuries
More informationA variety of other devices can be used with the front dee ring, but please check for suitability.
FULL BODY HARNESS Accredited to: EN 361 Web 45mm water resistant polyester. High tensile steel alloy & stainless/steel. 1.15 kg Rear & front attachment point, rip stitch indicators The TRGH2 harness is
More informationSAFEWORK PRACTICES EQUIVALENCY PROCEDURE FOR ACCESSING FLOATING ROOF TANKS ON STORAGE TANKS IN SERVICE CAT A-2 SOP #33
SUNCOR ENERGY PRODUCTS DISTRIBUTION TERMINAL OPERATING MANUAL STANDARD OPERATING PROCEDURE SAFEWORK PRACTICES EQUIVALENCY PROCEDURE FOR ACCESSING FLOATING ROOF TANKS ON STORAGE TANKS IN SERVICE Date Issued:
More informationUSE, ASSEMBLING AND MAINTEINANCE INSTRUCTIONS FOR CLIMBING LADDER
www.palicampion.it use, assembling and maintenance istrucrions for climbing ladder. rev130616 Pag. 1 di 9 USE, ASSEMBLING AND MAINTEINANCE INSTRUCTIONS FOR CLIMBING LADDER IMPORTANT: This documents concerns
More informationFOR. Society of Professional Rope Access Technicians P.O. Box 685 Rock Spring, GA Phone:
SAFE PRACTICES FOR ROPE ACCESS WORK Society of Professional Rope Access Technicians P.O. Box 685 Rock Spring, GA 30739 Phone: 303-794-0944 SAFE PRACTICES FOR ROPE ACCESS WORK INDEX 1. Scope and Purpose
More informationSöll GlideLoc vertical rail system
Created in cooperation with Europoles GmbH & Co. KG Söll GlideLoc vertical rail system Continuous fall protection system for fixed ladders Engineered for smooth operation for ascending/ descending Durable
More informationDeans, Directors, Heads of Schools and Departments and Research Institute Directors and Managers
Working at Height 1. PURPOSE 1.1 To ensure that any work at height is carried out in accordance with the legal requirements and associated guidance. This includes the use of scaffolds, towers, ladders,
More informationFALL PROTECTION PLAN FALL PROTECTION PROGRAM
FALL PROTECTION PLAN IMPORTANT: This document is intended to provide guidance only for developing site-specific fall protection plans for working at heights. FALL PROTECTION PLAN IMPORTANT: This document
More informationCertified in 3 & 4 leg configurations to CEN/TS 16415:2013 for maximum 2 persons and EN 795:2012 for single person use. total edge management system
Certified in 3 & 4 leg configurations to CEN/TS 16415:2013 for maximum 2 persons and EN 795:2012 for single person use total edge management system the world s most versatile modular total edge management
More informationFall Protection / Open Holes & Guardrail
Fall Protection / Open Holes & Guardrail 1. Leading Edges Policy Statement It is GW Communications policy that any worker exposed to a fall 6 or greater, shall be protected from coming into contact with
More informationUsage and maintenance manual for the fall arrester system of the Söll GlideLoc type with a guided type fall arrester. Söll Comfort 2. Order No.
Usage and maintenance manual for the fall arrester system of the Söll GlideLoc type with a guided type fall arrester Söll Comfort 2 Order No. 23331 in accordance with EN 353-1:2002 / CNB/P/11.073 Serial
More informationFALL PROTECTION (SAF-SPI-06)
1. PURPOSE To describe the Ontario Operations standard methods for preventing serious injury resulting from fall from heights and to provide a Standard for Fall Protection to safeguard employees who work
More informationAt the end of this presentation you should know the difference between fall prevention, fall restraint, and fall arrest.
0 At the end of this presentation you should know the difference between fall prevention, fall restraint, and fall arrest. We will review the hazards associated with fall protection and how to mitigate
More informationSample Fall Rescue Plan for Bridge Work
This document is intended to provide guidance for developing fall rescue plans for bridge contractors. The Occupational Safety and Health Administration s (OSHA) regulation 29 CFR 1926.502(d)(20) states:
More informationFALL PROTECTION PLAN INSTRUCTIONS
Sonic Drilling Ltd. FALL PROTECTION PLAN INSTRUCTIONS Each employer must ensure that a fall protection system is used when work is done at a place from which a fall of 3 m (10 ft) or more may occur, or
More informationWORK AT HEIGHT PROCEDURE
WORK AT HEIGHT PROCEDURE Rev No. Reason for Revision Prepared By Reviewed By Approval by Rev 00 Initial Release Navendra Singh Sanjay Kale Shrinivas Katti Rev 01 Standardization of Procedure Anil Jain
More informationFall Control User Instructions
Fall Control User Instructions Procedure BP-FCL-0096-01 branach.com sales@branach.com User Instructions These user instructions cover the following Branach products classified as for Professional use according
More informationSurface exploration drilling
Checklist Surface exploration drilling This checklist is intended to assist employers to identify common hazards and manage risks associated with surface exploration drilling. June 2017 Background In surface
More informationApplication of rope access methods in the construction, inspection, repair and maintenance of wind turbines
Application of rope access methods in the construction, inspection, repair and maintenance of wind turbines Introduction IRATA International s rope access system is a safe method of working at height,
More informationWorking at Height. A printed or saved copy is an UNCONTROLLED copy. Check that it is the latest available version before use.
A printed or saved copy is an UNCONTROLLED copy. Check that it is the latest available version before use. Title: Number: WORKING AT HEIGHT CSBP-GM-11-031-02 Version Number: 24.0.0 Date Revised: 10 September
More informationMANUFACTURING TECHNICAL INSTRUCTIONS - SAFETY FALL HAZARD CONTROL REQUIREMENTS SERIES & NO. SMI - 157
1 of 6 1.0 PURPOSE To establish minimum requirements and guidelines for controlling hazardous exposure of personnel to falls from working elevations in conformance with Federal and State OSHA rules and
More information8. Fall Protection Procedures WAC
1.0 Fall Protection Introduction 8. Fall Protection Procedures WAC 296-155-245 If an employee is exposed to a fall hazard of ten (10) feet or more in height, the employee must use a fall restraint, fall
More information2016 OFFSHORE TRAINING AND ASSESSMENT SERVICES
2016 OFFSHORE TRAINING AND ASSESSMENT SERVICES INTRODUCTION ILS is a specialist training and assessment provider operating on a global basis in the offshore oil and gas industry. Our specialist services
More information"FALL PREVENTION IN THE WORKPLACE"
MAJOR PROGRAM POINTS "FALL PREVENTION IN THE WORKPLACE" Part of the "GENERAL SAFETY SERIES" Quality Safety and Health Products, for Today...and Tomorrow Outline of Major Points Covered in the "Fall Protection"
More informationHeight Safety Lifting Load Control
01 Safety Height Safety Lifting Load Control Management GOTCHA ORIGINAL RESCUE KIT Technical Data Sheet SpanSet Australia Ltd 13 Pullman Place Emu Plains NSW 2750 Australia Telephone +61 2 4735 3955 Fax
More informationTRUSTED. DURABLE. RELIABLE.
SEALED-BLOK SELF RETRACTING LIFELINES TRUSTED. DURABLE. RELIABLE. FIELD PROVEN TECHNOLOGY RSQ FEATURE 420 LB. CAPACITY RETRIEVAL CAPABILITIES THE ULTIMATE IN FALL PROTECTION PRODUCT SHEET SEALED-BLOK SELF
More informationSWMS No 012 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 6
Samark North Qld Pty Ltd SWMS SWMS No 0 Samark North Qld Pty Ltd ABN : 99 08 98 87 Electrical Contractors License C37 Page of 6 Safe Work Method Statement Title: SWMS:0 INSTALLING LIGHT POLES Work Method
More informationTripod. System. User Instructions. 3M Occupational Health and Environmental Safety. Fall Protection Equipment
3M Occupational Health and Environmental Safety Fall Protection Equipment Tripod System User Instructions User Instructions for the 3M TM Tripod System. Important: Keep these User Instructions for reference.
More informationCompliance In A Can. Contents 1.0 HOW TO USE THIS MANUAL
Compliance In A Can This manual is intended to meet the Manufacturer s Instructions as required by ANSI Z359.1 and should be used as part of an employee training program as required by OSHA. Contents 1.0
More informationSafe Work Procedure for installation of external cladding
Safe Work Procedure for installation of external cladding This procedure has been formulated to cover safe systems of work for the installation of external cladding. This instruction will be used to reduce
More information