MiG-29 Scale EDF Radio Control model airplane

Transcription

1 MiG-9 Scale EDF Radio Control model airplane Wingspan : 45mm Model No : FF-D004 UNDER SFETY PRECUTIONS This radio control is not a toy! - lways keep this instruction manual ready on hand for quick reference. - ssemble this kit only places out of children reach. - First-time builders of EDF model should seek the advice of experienced modellers before beginning assembly and if they do not fully understand any parts of the construction. - Taking out liability insurance is recommended. - You are responsible for this model s assembly and safe operation. You need to purchase the following accessories separately to complete the assembly.. Signal cable (Throttle) 800mm pc required Electric Speed Control (ESC) w/ec 60 w/ EC pc required. Signal cable (Elevator) 800mm rushless Motor, kv, Shaft dia 5mm pcs required pc required 3. Silicone attery cable (No. WG or 4WG) 800mm pc required 7. Micro servo, torque >.8kg pcs required 4. Li-Po attery, 5-cells (8.5v), 3600mh, 0C pc required C Copyright 007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg.

2 Warning! First-time fliers should seek advice on pre-flight adjustments and assembly from experienced fliers. Remember that flying a badly assembled or badly adjusted aircraft is very dangerous! In The beginning, novice fliers should always be assisted by an experienced flier and should never fly alone! This model aircraft is designed to be powered by an electric-motor. Installing a over power motor and engine, or flying this model aggressively may lead to serious damage and accidents! Kit contents No Parts Qty Description No Parts Qty Description Canopy lock 8 5x0x3 plywood Canopy Vertical Tail Wing 4 4 mm collar 9 44x0x3 plywood mm collar xx3 plywood Fuselage 4 Linkage stopper 3x7x3 plywood 5 3 Landing gear 3mm plywood 6 x 90mm wire 3 3mm plywood Wing 7 Carbon rod 4 x x mm plywood 8 3x30mm screw 5 3mm plywood Horizontal Tail Wing Exhaust cone Nylon connector 0 3x0mm screw 6 4x0x3 plywood 3x0 screw 7 3xx3 plywood 3x3mm set screw 8 mm plywood Ducted Fan Unit pcs x4mm Screw Square stopper 3 x 50mm wire x 30mm wire 9 3mm plywood 30 3 Plastic parts 8 4 mm 3 mm Nose x Main x x 54mm wire 3 Foam Glue Foam glue Tools Required Epoxy Glue Scissors Screw driver Sharp Hobby Knife attery required Li-Po atteries (Motor) wl Double-sided Tape Solder --size atteries (Transmitter) Needle Nose Pliers 8mm ox Driver Solder Iron (80W above)

3 Fuselage Optional extension cable required for the connection of the and elevator servo.. Signal cable (Elevator) Optional extension cable required for the connection of the ESC.. Signal cable (Throttle) Fuselage 800mm pcs required. Silicone attery cable (No. WG or 4WG) 000mm 30 x x 3 plywood ESC 800mm pcs required pc required 3 mm plastic parts Note : () Install the servo cable before installing ducted fan unit. () Use Y extension cable to connect the ESC to receiver. FLYFLY HOY Copyright 007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg.

4 3 Horizontal Tail 30 x 5.6 x 3mm plywood 0 x 4 x 3mm plywood Sand a flat surface 7mm 5mm 4 Horizontal Tail FLYFLY HOY Copyright 007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg.

5 5 Front fuselage 6 Rear fuselage Elevator Throttle attery ir tank 5 x 0 x 3 plywood Optional Note : Li-Po Receiver Optional ir retract valve Diagram included the optional air retract system. Please refer to the retract system instruction for the installation method in detail. FLYFLY HOY 3 x 7 x 3mm plywood 44 x 0 x 3mm plywood Note : ssemble the front part in step-5 together. 4 x 0 x 3mm plywood 4 mm plastic parts 3 x x 3mm plywood Copyright 007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg.

6 7 8 Nose gear Nose gear 38 x 9.5 x 3 plywood FLYFLY HOY Copyright 007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg.

7 9 0 Wing construction Wing construction 4 mm plastic parts FLYFLY HOY Note : The cover designed for removable to access the motor & EDF. Note : Epoxy half of the cone only 4 mm plastic parts Copyright 007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg.

8 ssembly djustment FLYFLY HOY 60mm 4 x 600 carbon rod 40mm 4 x 350 carbon rod Copyright 007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg.

9 3 4 0 mm 0 mm = = djustment djustment Your radio require the elevon mixing ELEVTOR/ ILERON FLYFLY HOY Never fly before checking the CG s required position. In order to obtain the CG requirement, reposition the receiver and battery. NEVER fly the model without well balancing. 47mm (5.8 ) Note : djust the natural position of the elevator for level flight Copyright 007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg.

10 attery installation Note : If you intend to install pcs Li-Po battery, the diagram show the location for placing the battery. Li-Po battery FLYFLY HOY