AH-03: Bend Tubing. SAFETY FIRST o Follow all Caterpillar facility safety standards when performing this task.

Size: px
Start display at page:

Download "AH-03: Bend Tubing. SAFETY FIRST o Follow all Caterpillar facility safety standards when performing this task."

Transcription

1 AH-03: Bend Tubing Page 1 of 23 SAFETY FIRST o Follow all Caterpillar facility safety standards when performing this task. EQUIPMENT o tube benders, various sizes o levels o tube cutter, various sizes o squares o chamfer tools o tape measures o Parker #212FB Rotary flaring tool o various fittings RESOURCES o none Bend Tubing Note: This task will cover three types of bending profiles. Part A: Simple 90-degree ee Profile

2 Page 2 of Measure e the length of the tubing. Note: Always measure e from om centerline to centerline. o Select the appropriate measuring device shown below. o Using a tape measure and a square, make the first measurement. o Measure from the beveled end of the fitting to the centerline of the tube and record the results.

3 Page 3 of 23 o Measure from the beveled end of the other fitting to the centerline of the tube, and record the results. 2. Mark the tube for bending. o Mark the tube with the first measurement. Continue the mark completely around the tube.

4 Page 4 of 23 o Select the appropriate tube bender shown below. o Insert the tube into the tube bender. o Align the mark on the tube with the L on the tube bender. The L indicates that the measurement was taken from the left. If the measurement was taken from the right, align the mark on the tube with the R on the tube bender. o Ensure that the zeros on both parts of the tube bender are aligned.

5 Page 5 of 23 o Pull the top part of the tube bender down until the zero on the top portion is aligned with 90 on the bottom. 3. Cut the tubing to length. o Position the bent tube at the fittings. o Ensure that the left end of the tube is at the start of the beveled edge.

6 Page 6 of 23 o Position the opposite end of the tube at the start of the beveled edge, and mark the tube. 4. Cut the tube. o Select the appropriate tube cutter shown below. o Position the tube in the cutter and cut the tube.

7 Page 7 of Prepar epare e the cut ends of the tubing. o Select the appropriate chamfering tool shown below. o Place the tube in a vise. o Chamfer both inside and outside diameters. o Blow out the tube with compressed air.

8 6. Flare e the ends of the tube. Page 8 of 23 o Select the appropriate fitting shown below. Triple Lok 37, Intru Lok, and Ferulok Parker Fittings o Select the triple lok 37 degree shown below. Triple Lok 37

9 Page 9 of 23 o Slide the nut on the tube and then the ferrule. o Use the Parker #212FB Rotary Flaring tool or equivalent. Parker #212FB Rotary Flaring Tool o Insert the end with the nut and ferrule into the flaring tool.

10 Page 10 of 23 o Push the tube in until it is against the stop. o Slide the bolt and wing nut into the locking position, and tighten the wing nut finger-tight. o Lubricate the flaring cone with light oil.

11 Page 11 of 23 o Screw in the flaring cone until the end of the tube is flared. Note: Do not over or under flare the tube.

12 7. Install the tube. Page 12 of 23 Note: The tube should line up to the fittings, and the nuts on the tube should screw ew on easily.. Do not force ce the nuts on the fittings. o Check for any burrs and deburr if necessary. o Blow out the tube with compressed air. Part B: Tube with Two 45-degree ee Angles and a 90-degree ee Angle X = Y x 1.414

13 Page 13 of Mark the machine or surface using a square e and level. o Using the square, make a vertical mark above the fitting. o Make a mark not less than 2 1/4-inches above the fitting. This mark will indicate the 90-degree angle. If this mark is less than 2 1/4-inch, the tube end will not fit in the fairing tool. o Using a level, make a horizontal line to the right of the other fitting. 2. Draw out a plan for the tubing to identify the Y and X. o Measure from the 90-degree mark to the horizontal mark above the vertical line. This is the Y. o Multiply the Y number with 1.414, the results will be the X measurement. The constant of is only for 45-degree bends.

14 3. Bend the tube. Page 14 of 23 o Make the X measurements marks on the tube and ensure that the mark continues around the tube. o Insert the tube into the tube bender. This bend will be the first 45- degree bend. o Align the mark on the tube with the 45-degree mark on the top part of the tube bender. Ensure that the zeros on both parts on the tube bender are aligned. o Pull the top part of the tube bender down until the top zero lines up with the 45 on the bottom part.

15 Page 15 of 23 o Position the tube in the tube bender so that the second mark on the tube aligns with the 45 on the top portion of the tube bender. o Align the tube with the groove on the bottom portion of the tube bender to ensure a straight bend. The first bend is now pointing up. o Pull down on the top portion of the tube bender until the zero on the top is aligned with the 45 on the bottom. 4. Measure e the length of the tube to indicate where e the 90-degree ee bend should be made. o Measure from the fitting where the horizontal line is drawn to the vertical line. o Transfer the measurement to the drawing. o Lay the tube on the drawing and mark the tube for the 90-degree bend. o Place the tube in the tube bender. o Align the 90-degree mark on the tube with both zeros on the tube bender. o Align the tube with the groove on the bottom portion of the tube bender. o Pull down on the top portion of the tube bender until the zero on the top is aligned with the 90 on the bottom. 5. Cut the tubing to length. o Position the bent tube at the fittings. o Ensure that the left end of the tube is at the start of the beveled edge.

16 Page 16 of 23 o Position the opposite end of the tube at the start of the beveled edge and mark the tube. o Cut the tube. 6. Prepar epare e the cut ends of the tubing. o Place the tube in a vise. o Chamfer both inside and outside diameters. o Blow the tube out with compressed air. 7. Flare e the ends of the tube. o Slide the nut on the tube and then the ferrule. o Insert this end into the flare tool. o Push the tube in until it is against the stop. o Slide the bolt and wing nut into the locking position, and tighten the wing nut finger-tight. o Screw in the flaring cone until the end of the tube is flared. Note: Do not over or under flare the tube. 8. Install the tube. Note: The tube should line up to the fittings, and the nuts on the tube should screw on easily.. Do not force the nuts on the fittings. o Check for any burrs and deburr if necessary. o Blow out the tube with compressed air.

17 Page 17 of 23 Part C: Tube with Complex Bends Note: This tube will have a 90-degree ee and four 45-degree ee bends. The tube will be bent so that a length of it will rest against the wall. 1. Make both Y measurements ements first. o Using a small piece of tubing, lay the tubing against the wall. o Measure from the centerline on the tube to the center of the fitting. o Record this measurement.

18 Page 18 of 23 o Move to the opposite fitting, make the measurement, and record the readings. o Make a drawing and transfer both measurements to the drawing. These are the Y measurements. 2. Determine the X measurements. ements. o Multiply each Y measurement with the constant, o Record the results on the drawing. 3. Make a horizontal line at the top fitting. Make sure the line is centerline of the fitting. o Using a tape measure and square, measure the length of the tube. Measure from the horizontal line to the beveled edge of the bottom fitting, and record the results. 4. Mark the tube with the X measurements ements for the 45-degree ee bends. o Ensure that the marks continue around the tube. o Leave enough room for the 90-degree bend. 5. Make the 90-degree ee bend. o Ensure that there are at least 2 1/4-inches for the 90-degree bend and for the first 45-degree bend.

19 Page 19 of Make the first 45-degree ee bend. o Make the first X measurements on the tube and ensure that the mark continues around the tube. o Insert the tube into the tube bender. This is the first 45-degree bend. o Align the mark on the tube with the 45 mark on the top part of the tube bender. Ensure that the zeros on both parts on the tube bender are aligned. o Pull the top part of the tube bender down so that the zero on the top part of the tube bender lines up with the 45 on the bottom part.

20 Page 20 of Make the second 45-degree ee bend. o Position the tube in the tube bender so that the second mark on the tube aligns with the 45 on the top portion of the tube bender. o Align the tube with the groove on the bottom portion of the tube bender, to ensure a straight bend. o Pull down on the top portion of the tube bender until the zero on the top is aligned with the 45 on the bottom. 8. Make the third 45-degree ee bend. o Slide the tube in the tube bender so that the third mark on the tube aligns with the 45 on the top portion of the tube bender. o Align the tube with the groove on the bottom portion of the tube bender to ensure a straight bend. o Pull down on the top portion of the tube bender until the zero on the top is aligned with the 45 on the bottom. 9. Make the fourth 45-degree ee bend. o Position the tube in the tube bender so that the fourth mark on the tube aligns with the 45 on the top portion of the tube bender. o Align the tube with the groove on the bottom portion of the tube bender, to ensure a straight bend. o Pull down on the top portion of the tube bender until the zero on the top is aligned with the 45 on the bottom.

21 10. Make the 90-degree ee bend. Page 21 of 23 o Position the tube in the tube bender so that the 90-degree mark on the tube aligns with the zero on the top portion of the tube bender. o Align the tube with the groove on the bottom portion of the tube bender, to ensure a straight bend. o Pull down on the top portion of the tube bender until the zero on the top is aligned with the 90 on the bottom Cut the tubing to length. o Position the bent tube at the fittings. o Ensure that the left end of the tube is at the start of the beveled edge. o Position the opposite end of the tube at the start of the beveled edge, and mark the tube. o Cut the tube. 12. Prepar epare e the cut ends of the tubing. o Place the tube in a vise. o Chamfer both inside and outside diameters. o Blow the tube out with compressed air. 13. Flare the ends of the tube. o Slide the nut on the tube and then the ferrule. o Insert this end in the flare tool. o Push the tube in until it is against the stop. o Slide the bolt and wing nut into the locking position and tighten the wing nut finger-tight. o Screw in the flaring cone until the end of the tube is flared. Note: Do not over or under flare the tube. 14. Install the tube.

22 Page 22 of 23 Note: The tube should line up to the fittings, and the nuts on the tube should screw ew on easily.. Do not force ce the nuts on the fittings. o Check for any burrs and deburr if necessary. o Blow out the tube with compressed air. Part D: Compression and Flareless Fitting Assemblies Flodar,, Imperial Eastman Hy Duty Flareless, and Weather eatherhead head Compression Note: Follow the same procedur ocedures es as with flared fittings but with some exceptions listed below. 1. Ensure that the amount of tubing which terminates inside the fittings is factored in on all length calculations. 2. On 90-degree ee bends the fitting end can be less than 2 1/4-inch as clearance for a flaring tool does not have to be factored in.

23 Page 23 of Ensure e that the tube ends are e square e and deburred ed inside and outside diameters. 4. Ensure e that the tubing is seated at the bottom of the ID of the fitting assembly. 5. Ensure e that the compression ferrule ule slide easily over the tube. 6. Ensure e that the assembly nut is not over torqued. 7. Assemblies should be bench assembled in a vise with soft clamps whenever possible.

COMPRESSION TUBE FITTINGS

COMPRESSION TUBE FITTINGS COMPRESSION TUBE FITTINGS 1/16 THROUGH 2 2 MM THROUGH 50 MM LET-LOK TUBE FITTINGS DESCRIPTION The HAM-LET GROUP has produced high quality tube and pipe LET-LOK HOW DOES IT WORK? A HAM-LET has gained an

More information

COMPRESSION TUBE FITTINGS 1/16 THROUGH 2 -INCH, 2 MM THROUGH 50 MM-METRIC

COMPRESSION TUBE FITTINGS 1/16 THROUGH 2 -INCH, 2 MM THROUGH 50 MM-METRIC 1/16 THROUGH 2 -INCH, 2 MM THROUGH 50 MM-METRIC LET-LOK TUBE FITTINGS DESCRIPTION HAM-LET LET-LOK HOW DOES IT WORK? HAM-LET LET-LOK LET-LOK LET-LOK HAM-LET LET-LOK 1 4 3 2 4 Tube 1 2 3 1 2 3 4 6 LET-LOK

More information

IMPORTANT: RECEIVING INSTRUCTIONS:

IMPORTANT: RECEIVING INSTRUCTIONS: Instruction Sheet Sidewinder Mechanical Bender IMPORTANT: RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any shipping damage is found, notify carrier at once.shipping damage

More information

Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B

Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 080311-2 SP3363-1 Side-of-Pole Mount for 1 Module (SPM1)

More information

COMPRESSION TUBE FITTINGS

COMPRESSION TUBE FITTINGS COMPRESSION TUBE FITTINGS 1/16 THROUGH 2 2 MM THROUGH 50 MM LET-LOK TUBE FITTINGS DESCRIPTION The HAM-LET GROUP has produced high quality tube and pipe fittings in various materials for high pressure applications

More information

Torque Specifications

Torque Specifications SENR3130-10 Torque Specifications All Caterpillar Products S/N From the library of Barrington Diesel Club CONTENT General Information 01/07/2005 Introduction to Torque 01/07/2005 Torque-Turn 01/07/2005

More information

FLEXIBLE SHAFTING (Wet & Dry)

FLEXIBLE SHAFTING (Wet & Dry) TM-5 April 5, 2004 Elliott offers a complete line of precision tube tools, including: tube expanders Boiler Expanders Heat Exchanger Expanders Condenser Expanders Refinery Expanders tube rolling motors

More information

Final Assembly Instructions Bikes with Quill Stems

Final Assembly Instructions Bikes with Quill Stems Final Assembly Instructions Bikes with Quill Stems Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert

More information

Tube Fabricating Equipment

Tube Fabricating Equipment Tube Fabricating Equipment Tube Fabricating Equipment Tube cutters Tube Benders Flaring Tools Flaring Tool Kits Swaging Tools Testing & Service Tools Deburring Tool The World Standard Tube Cutters Sizes

More information

Installation Instructions

Installation Instructions 116-3027, 116-3017 X-Pando Adjustable Steel Protector Installation Instructions 1404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 NB 6/28/10 607-0112 Step 1. Mounting

More information

Assembly Instructions

Assembly Instructions CS-B-FM Assembly Instructions Thank you for purchasing a Shelti product. All of us at Shelti want you to be completely satisfied with your Pro Foos game, so feel free to contact us for help with the assembly

More information

Tube Fabricating Equipment Introduction At Parker, we feel that proper tube selection and installation are key ingredients to building leak-free, reli

Tube Fabricating Equipment Introduction At Parker, we feel that proper tube selection and installation are key ingredients to building leak-free, reli Tube Fabricating Equipment Catalog 4290 Revised, July 2000 Tube Fabricating Equipment Introduction At Parker, we feel that proper tube selection and installation are key ingredients to building leak-free,

More information

// ADapters GUIDelines

// ADapters GUIDelines // ADapters GUIDelines ADAPTER SELECTION Selection of an appropriate ALFAGOMMA adapter for a given application depends on the fluid system operating parameters listed below and the tube material and wall

More information

Final Assembly Instructions Bikes with Threaded Headsets

Final Assembly Instructions Bikes with Threaded Headsets Final Assembly Instructions Bikes with Threaded Headsets Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our

More information

To save this document, scroll up and select the download icon

To save this document, scroll up and select the download icon Thank you for purchasing a RustySpokes Softcruise. We know you are going to enjoy the bike, but if you had it shipped to you, there are a few things you need to do to assemble the bike. The seat, pedals

More information

Rapidmain Installation Guide

Rapidmain Installation Guide Rapidmain Installation Guide Aluminium Compressed Air Pipe Work Installation Guide Trafalgar Court, Waterloo Ind Estate, Widnes Cheshire. UK. Ref: Rapidmain installation guide 4b Index 1. Rapidmain fittings:

More information

FITTING IDENTIFICATION AMERICANT THREAD TYPES APPENDIX ALFAGOMMA // APPENDIX. Dash numers. NPTF (National Pipe Tapered Fuel)

FITTING IDENTIFICATION AMERICANT THREAD TYPES APPENDIX ALFAGOMMA // APPENDIX. Dash numers. NPTF (National Pipe Tapered Fuel) // FITTINGS GUIDelines FITTING IDENTIFICATION numers Most fluid piping system sizes are measured by dash numbers. These are universally used abbreviations for the size of component expressed as the numerator

More information

Tools & Installation. Tools & Installation Index

Tools & Installation. Tools & Installation Index L Radius +0 59-2 32 60 +2 A B -0 32 C E F.09" ia. Weep Hole Tools & Installation MAXIMATOR offers manual Coning and Threading tools that are designed to prepare accurate tubing ends to accept the medium,

More information

Troyer s Gourd Rack 8 unit F R H O P

Troyer s Gourd Rack 8 unit F R H O P B E A D I M-N L Vertical Parts F R H O P Horizontal Parts C G J Updated 11/16 Parts List A: Top of Pole B: Bottom of Pole C: 48 Ground Stake D: Top Perch rods 48 long E: Hub F: Rope Winder w/ attached

More information

Connecting a SSL/PTV Backflush System

Connecting a SSL/PTV Backflush System This section provides instructions for connecting your SSLBKF/PTVBKF injector modules with pre-column and analytical capillary column into the oven. Refer to the chapters SSLBKF Injector Module and PTVBKF

More information

MASTER TRUING STAND TS-3. Optional Dial indicator set with brackets Dial indicator bracket set only

MASTER TRUING STAND TS-3. Optional Dial indicator set with brackets Dial indicator bracket set only MASTER TRUING STAND TS-3 3 2 1 3 8 9 4 10 7 6 5 12 13 Optional 1555-1 Dial indicator set with brackets 1556-1 Dial indicator bracket set only 49 11 16 14 15 48 32 31 37 38 20 19 17 18 34 39 21 36 22 33

More information

Side-of-Pole Mount for 1 Module (SPM1) For Module Type C

Side-of-Pole Mount for 1 Module (SPM1) For Module Type C Module Type Width Length C 22-27 56-63 Side-of-Pole Mount for 1 Module (SPM1) For Module Type C ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 022212-1 Side-of-Pole Mount

More information

EXTERNALLY ROUTED DROPPER POST owner S MANUAL

EXTERNALLY ROUTED DROPPER POST owner S MANUAL EXTERNALLY ROUTED DROPPER POST owner S MANUAL Introduction: This adjustable height seat post with internal cable routing allows for micro-adjustments using a remote handlebar mounted lever. The cable actuated

More information

TABLE OF CONTENTS FRAME FEATURES INTRODUCTION

TABLE OF CONTENTS FRAME FEATURES INTRODUCTION S3 DISC MANUAL TABLE OF CONTENTS Introduction...1 Frame Features...2 Fork Preparation...3 Small Parts...5 Frame Preparation...6 Brake Housing Installation...7 Mechanical Cable Routing...9 Electric Cable

More information

Horizontal Fuselage. Top Vertical Fuselage 1. Lay out the Top Vertical Fuse Front(1), Top Vertical Fuse Back(2), and Vertical Stabilizer(3).

Horizontal Fuselage. Top Vertical Fuselage 1. Lay out the Top Vertical Fuse Front(1), Top Vertical Fuse Back(2), and Vertical Stabilizer(3). Rumbuilder 71 B-17 Congrats on your Rumbuilder B-17! We re glad you chose to fly with us! If you have any problems, or missing/broken kit pieces, please contact us. We d be happy to replace any damaged

More information

A. TO PREPARE THE MACHINE FOR USE.

A. TO PREPARE THE MACHINE FOR USE. INSTRUCTION MANUAL FOR THE ML120 STRINGING MACHINE. CONTENTS: A. TO PREPARE THE MACHINE FOR USE. 1. The assembly of frame with console and tooltray. 2. Fixing the lever of the tension unit. 3. Putting

More information

Syringe, Distribution Valve and Infusion Pump Removal/Replacement ATTENTION SYRINGE REPLACEMENT

Syringe, Distribution Valve and Infusion Pump Removal/Replacement ATTENTION SYRINGE REPLACEMENT ATTENTION SYRINGE REPLACEMENT Please read through the document completely before starting any repairs. Refer to the proper section in the service manual for complete removal and replacement procedures.

More information

SHUR-LOK CORPORATION TECHNICAL SALES BULLETIN

SHUR-LOK CORPORATION TECHNICAL SALES BULLETIN Page 1 of 9 1. SCOPE: 1.1. This provides the minimum design, port preparation and installation and removal requirements for SLAS4383-XX-XX, SLF2002-XX-XX and SLF3004-XX-XX adapter reducer and is applicable

More information

Foos 300 Assembly Instructions

Foos 300 Assembly Instructions Foos 300 Assembly Instructions Thank you for purchasing a Shelti product. All of us at Shelti want you to be completely satisfied with your Foos game, so feel free to contact us for help with the assembly

More information

General page Straight unions page Angle unions page Tee and L-unions page Gauge connection unions page 42

General page Straight unions page Angle unions page Tee and L-unions page Gauge connection unions page 42 C 2610-00 Table of contents General page 3-13 DILO unions for pressure ranges from 100 320 bar Straight unions page 14-25 Weld-on tube unions page 14-16 Screw-in tube unions page 17-25 with metric / Whitworth-

More information

Final Assembly Instructions Bikes with Threaded Headsets

Final Assembly Instructions Bikes with Threaded Headsets Final Assembly Instructions Bikes with Threaded Headsets Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our

More information

Tube Fabricating Equipment. Catalog 4290 Revised, August 2003

Tube Fabricating Equipment. Catalog 4290 Revised, August 2003 Tube Fabricating Equipment Catalog 4290 Revised, August 2003 Introduction At Parker, we feel that proper tube selection and installation are key ingredients to building leak-free, reliable tubing systems.

More information

2019 MADONE ASSEMBLY MANUAL

2019 MADONE ASSEMBLY MANUAL 2019 MADONE ASSEMBLY MANUAL 2019 MADONE Rim brakes and Di2 drivetrain Rim brakes and mechanical drivetrain Disc brakes and Di2 drivetrain Disc brakes and mechanical drivetrain TABLE OF CONTENTS Common

More information

No Mausers Lost Their Lives in the Production of This Article

No Mausers Lost Their Lives in the Production of This Article No Mausers Lost Their Lives in the Production of This Article by RGI Media, Inc - Published with permission The problem with working on Cosmoline soaked WWII relics is that the process is addictive. Projects

More information

8MAY15 US RACK, Inc Falcon Drive, Madera, CA

8MAY15 US RACK, Inc Falcon Drive, Madera, CA 8MAY15 US RACK, Inc. - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTRUCTIONS for Bedrail-mounted MOTORCYCLE RACK, Model 2001-4TRA WARNING: Do NOT attempt to install or use this rack without following

More information

Operating & Maintenance MANUAL

Operating & Maintenance MANUAL Operating & Maintenance MANUAL Thank You for purchasing the golf industry s state-of-the-art STEELCLUB Putter Angle Machine. You should find it simple to operate. Please follow the instructions in this

More information

Hydraulic Piston Accumulators

Hydraulic Piston Accumulators Ride Control Engineering Services PWCE Extendavator Paul Wever Construction Equipment Co., Inc. P.O. Box 85 401 Martin Drive Goodfield, IL 61742-0085 Phone (309) 965-2005 Fax (309) 965-2905 1-800-990-PWCE

More information

QUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift

QUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your

More information

Armorer s Handgun Sight Tool

Armorer s Handgun Sight Tool Armorer s Handgun Sight Tool Product #710905 Instructions #1054680 Rev. B 2 Top Knobs Height Adjustment Screw Adjustment Wheel Front Pusher Block Top Carriage Assembly 2 Front Pusher Block Screws Bottom

More information

INSTALLING THE BOLT-IN-PLACE FOOTPLATE KIT (FIGURE 1)

INSTALLING THE BOLT-IN-PLACE FOOTPLATE KIT (FIGURE 1) Bolt-In-Place/Spring Button Assembly and Installation Instructions Kits No. 1110266 and 1121271 SAVE THESE INSTRUCTIONS NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use.

More information

SAMPLE PAGE. Section 2... Wire Rope

SAMPLE PAGE. Section 2... Wire Rope Section 2...................................................... Wire Rope Never use any kind of clip to directly connect two straight lengths of wire rope to form a continuous piece. Do not make up slings

More information

Side-of-Pole Mount for 1 Modules (SPM1) For Module Types E, F, G, & H ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation

Side-of-Pole Mount for 1 Modules (SPM1) For Module Types E, F, G, & H ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation Side-of-Pole Mount for 1 Modules (SPM1) For Module Types E, F, G, & H ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A SP3348-1 PCN 022212-2 Side-of-Pole Mount for 1 Module

More information

>B< Press Range. SALES: +44 (0) FAX: +44 (0) WEB:

>B< Press Range. SALES: +44 (0) FAX: +44 (0) WEB: >B< Press Range SALES: +44 (0)121 557 2831 FAX: +44 (0)121 520 8778 WEB: ibpconex.co.uk EMAIL: sales@ibpgroup.com 74 75 MATERIAL TUBE SPECIFICATION SIZE 6mm to 18mm 22mm 28mm to 54mm N o of turns 11 4

More information

VERSA BIKE RACK INSTRUCTIONS

VERSA BIKE RACK INSTRUCTIONS VERSA BIKE RACK INSTRUCTIONS Models #8, 8 Important This rack is designed for use with a or. receiver hitch. The rack is designed to hold a maximum of two bicycles. Do not use it for anything other than

More information

INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER

INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 - Rubber 2 - Rail Assemblies 1 - Rudder Body 1 - Rudder Retraction Grommets

More information

8. Carefully layout all the parts of the reservoir setup and clean any dirt, grime or dust from the parts. ( image 8 ) 8

8. Carefully layout all the parts of the reservoir setup and clean any dirt, grime or dust from the parts. ( image 8 ) 8 INSTRUCTIONS TO SERVICE AMADAXTREME SHOCKS 2.0 REMOTE RES AUSTRALIAN VERSION PART 1 - SERVICE THE RESERVOIR 1.Prior to cleaning the shock check for any leaks or signs of damage to the res, lines, bushes

More information

Final Assembly Instructions Bikes with 16 Wheel Size

Final Assembly Instructions Bikes with 16 Wheel Size Final Assembly Instructions Bikes with 16 Wheel Size Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert

More information

PXRF- Tracer Helium Flow Control System

PXRF- Tracer Helium Flow Control System PXRF- Tracer Helium Flow Control System This flow control system was designed to regulate the gas flow from a helium (He) balloon tank containing 8.9 cu ft (0.25 cu m). Tank not included with the system.

More information

User s Manual. Model SWTC800. CAUTION: Adult Assembly Required

User s Manual. Model SWTC800. CAUTION: Adult Assembly Required User s Manual Model SWTC800 CAUTION: Adult Assembly Required Model SWTC800...3...4...4...5...6.........8...9...10-11 Part Identification Chart... 12 Exploded Drawing and Parts List...13-14 Ordering Replacement

More information

Push-Lok 801/804/821/836 Hose and Fittings

Push-Lok 801/804/821/836 Hose and Fittings Push-Lok 801/804/821/836 Hose and Fittings Parker Push-Lok The Most Complete Line of Premium-Quality, Low-Pressure Hose and Fittings Push-Lok Plus 801 hose provides the quick and easy assembly/ disassembly

More information

>B< Press Range. SALES: +44 (0) FAX: +44 (0) WEB:

>B< Press Range. SALES: +44 (0) FAX: +44 (0) WEB: >B< Press Range SALES: +44 (0)121 557 2831 FAX: +44 (0)121 520 8778 WEB: ibpconex.co.uk EMAIL: sales@ibpgroup.com 74 75 MATERIAL TUBE SPECIFICATION SIZE 6mm to 18mm 22mm 28mm to 54mm N o of turns 11 4

More information

Road Chain Catcher Installation Instructions (K13-001, K13-006, K SL1, K SL2)

Road Chain Catcher Installation Instructions (K13-001, K13-006, K SL1, K SL2) Road Chain Catcher Installation Instructions (K13-001, K13-006, K13-001-SL1, K13-001-SL2) Description: The K-Edge Road Chain Catcher series is designed to eliminate chain drop on the lowest chainring due

More information

BOYLE S / CHARLES LAW APPARATUS - 1m long

BOYLE S / CHARLES LAW APPARATUS - 1m long BOYLE S / CHARLES LAW APPARATUS - 1m long Cat: MF0340-101 (combination Boyle s and Charles without mercury) DESCRIPTION: The IEC Boyle's & Charles Law apparatus is a high quality instrument designed to

More information

Techcon Systems TS1258 Pressure Pot

Techcon Systems TS1258 Pressure Pot Techcon Systems TS1258 Pressure Pot User Guide TABLE OF CONTENT 1. SAFETY. 3 1.1 Intended Use 3 1.2 Safety Precaution 3 2. CERTIFICATE OF COMFORMANCE 4 3. FEATURES. 5 4. SPECIFICATIONS 5 5. INSTALLATION

More information

SERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.

SERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding

More information

Shifting Lever. RAPIDFIRE Plus 11-speed

Shifting Lever. RAPIDFIRE Plus 11-speed (English) DM-SL0005-04 Shifting Lever Dealer's Manual RAPIDFIRE Plus 11-speed MTB XTR SL-M9000 DEORE XT SL-M8000 CONTENTS IMPORTANT NOTICE... 3 TO ENSURE SAFETY... 4 LIST OF TOOLS TO BE USED... 7 INSTALLATION...

More information

DM-RCWH (English) Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike. Wheel Set. WH-RX31 SM-AX x12 SM-AX x12

DM-RCWH (English) Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike. Wheel Set. WH-RX31 SM-AX x12 SM-AX x12 (English) DM-RCWH001-00 Dealer's Manual ROAD MTB Trekking City Touring/ Comfort Bike URBAN SPORT E-BIKE Wheel Set WH-RX31 SM-AX720-100x12 SM-AX720-142x12 CONTENTS IMPORTANT NOTICE... 3 TO ENSURE SAFETY...

More information

Sidemount Dovetail saddles User manual

Sidemount Dovetail saddles User manual Sidemount Dovetail saddles User manual March 2016 1/9 www.trackthestars.com Contents Introduction... 3 Product safety... 3 Receiving the Sidemount Dovetail Saddle... 4 Installation... 4 Remove Top Mount

More information

NEXT GENERATION FLEX FENCE

NEXT GENERATION FLEX FENCE NEXT GENERATION FLEX FENCE Area To Be Fenced.. With Next Generation Flex Fence any post that is not in a straight line with another post must be braced. Layout your fence installation. Determine all end

More information

1.0 - OPENING AND CLOSING THE DOOR

1.0 - OPENING AND CLOSING THE DOOR The purpose of this manual is to provide the user with instructions on how to safely open and close, how to conduct routine maintenance, and how to install the PEI TWINLOCK Closure on a pressure vessel.

More information

FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions

FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions WARNING! WARNING! WARNING! THIS BASKETBALL SYSTEM IS SPRING LOADED AND SHIPPED UNDER TENSION. ATTEMPTING TO ASSEMBLE OR DISASSEMBLE ANY

More information

READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.

READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. Drywall Stills DS1830 Max Weight Capacity 225 Lb READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance. Every effort

More information

Gurney Flap for WRX and STI w/low Profile Trunk Spoiler

Gurney Flap for WRX and STI w/low Profile Trunk Spoiler Gurney Flap for 2015+ WRX and STI w/low Profile Trunk Spoiler 2017-12-05 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced

More information

INSTALLING THE PROWLER 13 RUDDER

INSTALLING THE PROWLER 13 RUDDER INSTALLING THE PROWLER 13 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 Rubber 2 Rail Assemblies Rudder Body 1 Rudder Retraction Grommets (includes steering

More information

Important Note: Tighten lock nuts so the support tubes still swing freely see figure 2. There must be 1 2 threads of bolt past end of lock nuts.

Important Note: Tighten lock nuts so the support tubes still swing freely see figure 2. There must be 1 2 threads of bolt past end of lock nuts. Kit Contents: DESCRIPTION QTY. DESCRIPTION QTY. 2 Shank Assembly 1 Support Tube Assembly 1 Side Tube - Short 2 1-1/4 Shank 1 Center Tube - Long 1 3/8-16 x 2.0 Carriage Bolt 2 5/16-18 x 2.25 Carriage Bolt

More information

Operating Instructions for Cobra and Lynx Duct Leakage Testers

Operating Instructions for Cobra and Lynx Duct Leakage Testers Operating Instructions for Cobra and Lynx Duct Leakage Testers Table of Contents Introduction Introduction... 2 Safety Precautions Safety Precautions.. 2 Prior to Testing System Preparation.. 4 Power Requirements...

More information

Two Ferrule Tube Fittings 316 stainless steel ranging from 1/8" to 1" (6mm to 25mm) O.D.

Two Ferrule Tube Fittings 316 stainless steel ranging from 1/8 to 1 (6mm to 25mm) O.D. Two errule Tube ittings 316 stainless steel ranging from 1/8" to 1" (6mm to 25mm) valve & fitting www.veelok.com Introduction Vee-Lok tube fittings are designed to provide a leak-free connection and applied

More information

2019 MADONE ASSEMBLY MANUAL

2019 MADONE ASSEMBLY MANUAL 2019 MADONE ASSEMBLY MANUAL 2019 MADONE Rim brakes and Di2 drivetrain Disc brakes and Di2 drivetrain Rim brakes and mechanical drivetrain Disc brakes and mechanical drivetrain TABLE OF CONTENTS Common

More information

Installation Instructions for the AlphaDeck Staging System

Installation Instructions for the AlphaDeck Staging System Installation Instructions for the AlphaDeck Staging System Step 1 - Preparation A. Before setting up this system, determine the location of the stages and all the parts you will need. B. Read through the

More information

Installation and Training Manual

Installation and Training Manual AirForce1 Tower Kit Installation and Training Manual FuturEnergy Limited Ettington Park Business Centre Stratford upon Avon CV37 8BT +44 (0)1789 451070 Table of Contents Safety Notes... 3 Parts Supplied

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS KIT CONTENTS: PART NUMBER: DESCRIPTION: E361SXA300 ROOF MOUNT BICYCLE CARRIER B9 TRIBECA Short Carriage Bolt Long Carriage Bolt 3x Over-Molded Wrench Button Head Screw 2x Washer

More information

SPOOLER INSTRUCTIONS. STEP 12 If you are going to paint your posts, that should be done at this time.

SPOOLER INSTRUCTIONS. STEP 12 If you are going to paint your posts, that should be done at this time. STEP 4 Starting where you marked the end post location, move down your fence line 6 feet and make another mark. This mark is where your second upright post will be installed. Continuing down the fence

More information

RUDDER KIT INSTRUCTIONS

RUDDER KIT INSTRUCTIONS C I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS PAMLICOS-0,0,T, T, 60T, Excel Rotomolded Pamlico 0, 0, T, T, 60T, Excel The addition of a rudder to a kayak results in additional control and efficiency,

More information

RATCHET RELEASE SHACKLE

RATCHET RELEASE SHACKLE RATCHET RELEASE SHACKLE INNOVATIVE PILING EQUIPMENT HYDRAULIC PILING HAMMERS EURO RATCHET RELEASE SHACKLE FOR STEEL ERECTION OPERATORS INSTRUCTIONS & SPARE PARTS LIST EXCAVATOR MOUNTED VIBRATORS EXCAVATOR

More information

PULLTARP INSTALLATION & OPERATORS MANUAL

PULLTARP INSTALLATION & OPERATORS MANUAL PULLTARP INSTALLATION & OPERATORS MANUAL Step 1. Mounting Positions Determine the mounting position for your truck Fig. 1 - Fig. 7. Fig. 1 Fig. 2 Fig. 3 A Mount Top Or Bottom Roll B Mount Top Or Bottom

More information

Movement: Using the chest muscles and a slight bend in the elbow, bring your arms together in front of your chest.

Movement: Using the chest muscles and a slight bend in the elbow, bring your arms together in front of your chest. Chest Fly Anchor: Chest height Start: Stand with a split stance arms open out to the side, palms facing forward. Movement: Using the chest muscles and a slight bend in the elbow, bring your arms together

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Models No. TD0101, TD0101F Description Impact Driver L PRODUCT P 1/ 14 CONCEPT AND MAIN APPLICATIONS Models TD0101 and TD0101F are cost-competitive 100N.m-class impact driver developed

More information

Cable Replacement Instructions for R-Series Roust-A-Bout 100/150/250

Cable Replacement Instructions for R-Series Roust-A-Bout 100/150/250 Cable Replacement Instructions for R-Series Roust-A-Bout 100/150/250 US 7514 Alabonson Road Houston, TX 77088 phone: 281-999-6900 fax: 281-999-6966 Canada 1721 Bishop St. Unit #4 Cambridge, ON N1T 1N5

More information

Poppetted Coaxial Drop Tube Assembly for use with Auto Limiter II. Installation Instructions

Poppetted Coaxial Drop Tube Assembly for use with Auto Limiter II. Installation Instructions Poppetted Coaxial Drop Tube Assembly for use with Auto Limiter II Installation Instructions Franklin Fueling Systems 3760 Marsh Rd. Madison, WI 53718 USA Tel: +1 608 838 8786 800 225 9787 Fax: +1 608 838

More information

>B< Press Range. SALES: +44 (0) FAX: +44 (0) WEB:

>B< Press Range. SALES: +44 (0) FAX: +44 (0) WEB: >B< Press Range SALES: +44 (0)121 557 2831 FAX: +44 (0)121 520 8778 WEB: ibpconex.co.uk EMAIL: sales@ibpgroup.com 74 75 MATERIAL TUBE SPECIFICATION SIZE 6mm to 18mm 22mm 28mm to 54mm N o of turns 11 4

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS KIT CONTENTS: INSTALLATION INSTRUCTIONS PART NUMBER: DESCRIPTION: E361SXA302 roof MOUNT BICycle CARRIER SINGLE Short Carriage Bolt 1x Long Carriage Bolt 3x Over-Molded Wrench 1x Button Head Screw 2x Washer

More information

Mini Mr.Bulletfeeder by Double-Alpha

Mini Mr.Bulletfeeder by Double-Alpha Mini Mr.Bulletfeeder by Double-Alpha User Manual Thank you for choosing the Mini Mr.Bulletfeeder by Double-Alpha! This newly designed product will give you years of reliable service. It will make your

More information

All DZR stopvalve (BS1010). copper x copper. Gunmetal body. All parts in contact with water are made from material resistant to dezincification.

All DZR stopvalve (BS1010). copper x copper. Gunmetal body. All parts in contact with water are made from material resistant to dezincification. All DZR stopvalve (BS1010). copper x copper. Gunmetal body. All parts in contact with water are made from material resistant to dezincification. K551DZR Size Pattern No. Pack 1 Qty Pack 2 Qty Code Barcode

More information

Tripod Setup Guide (M-TPx)

Tripod Setup Guide (M-TPx) Items needed: 1/2 inch wrench, mast level (M-MLA), medium size wire cutters, crescent wrench, all-purpose grease, tape measure, tie wraps, redi-mix cement (optional), shovel (optional), sledge hammer (for

More information

Intru-lok Flareless Bite Type Fittings

Intru-lok Flareless Bite Type Fittings Intru-lok Flareless Bite Type Fittings 4300 atalog Flareless Bite Type Fittings Nuts, Ferrules, Inserts BIP Knurled Nut BI2 Nut BTI2 Nut and Ferrule TI2 Ferrule TIP Expander / Insert T23UI Insert HBI2

More information

SASK-A-POLE OWNERS AND USERS MANUAL

SASK-A-POLE OWNERS AND USERS MANUAL SASK-A-POLE OWNERS AND USERS MANUAL GENERAL INFORMATION The Saskatchewan Abilities Council s Sask-a-Pole accessibility and transfer aid is designed to help provide safe and easy access to chairs, beds,

More information

TO RECEIVE the most benefit from a

TO RECEIVE the most benefit from a Using Surveying Equipment TO RECEIVE the most benefit from a tool, it must be used properly. In addition, it must be well maintained. In most cases, the user will need some instruction and training regarding

More information

SCUBAPRO Repair Guide. S600-S550 Second Stages

SCUBAPRO Repair Guide. S600-S550 Second Stages SCUBAPRO Repair Guide S600-S550 Second Stages S600 Configuration A S600 Configuration B USE THIS GUIDE AS A REFERENCE WHEN SERVICING THE S600 AND S550 SECOND STAGES S550 P/N 41-047-000 FOR REPAIR OF S600-S550

More information

Instructions. Follow All Instructions Before Assembling Or Using This Product

Instructions. Follow All Instructions Before Assembling Or Using This Product Instructions Follow All Instructions Before Assembling Or Using This Product IMPORTANT DO NOT RETURN THIS PRODUCT TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE: (800) 492-9334 WARNING: Improper use

More information

Lectric Cycles Mid-Drive Electric Motor Installation

Lectric Cycles Mid-Drive Electric Motor Installation Lectric Cycles Mid-Drive Electric Motor Installation This write-up describes the installation of a Lectric Cycles electric motor. The model is the e-rad Mid-Drive 750 Watt conversion kit, installed on

More information

GATE INSTALLATION INSTRUCTIONS

GATE INSTALLATION INSTRUCTIONS For Technical Support: 1-877-862-7049 GATE INSTALLATION INSTRUCTIONS What You Need: Posthole digger 4 long, 2 diameter galvanized pipe For Loose Soil 3 additional 3 long, 2 diameter galvanized pipe Level,

More information

Cantilever Brake. Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike

Cantilever Brake. Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike (English) DM-RCBR001-00 Dealer's Manual ROAD MTB Trekking City Touring/ Comfort Bike URBAN SPORT E-BIKE Cantilever Brake BR-CX70 BR-CX50 BL-4700 BL-4600 BL-R780 BL-R3000 ST-7900 ST-6700 ST-5700 ST-4600

More information

Olympic Flat Bench with weight set

Olympic Flat Bench with weight set Project: Olympic Flat Bench With Weight Set Page 1 of 33 Olympic Flat Bench with weight set NOTE: The measurements within this text and 2D documentation are given both in millimeters and inches (in brackets).

More information

Flat Bench. Use various tools and clamps in process of welding, so you could weld the items together with accuracy.

Flat Bench. Use various tools and clamps in process of welding, so you could weld the items together with accuracy. Project: Flat Bench Page 1 of 50 Flat Bench The measurements within this text and 2D documentation are given both in millimeters and inches (in brackets). This website is based on ISO measurement unit

More information

>B< Press Range. SALES: +44 (0) FAX: +44 (0) WEB:

>B< Press Range. SALES: +44 (0) FAX: +44 (0) WEB: >B< Press Range SALES: +44 (0)121 557 2831 FAX: +44 (0)121 520 8778 WEB: ibpconex.co.uk EMAIL: sales@ibpgroup.com 74 75 MATERIAL TUBE SPECIFICATION SIZE 6mm to 18mm 22mm 28mm to 54mm N o of turns 11 4

More information

Contents. Stainless Steel Side Block. 1.1 Separating the Side Block. Stainless Steel Side Block Reassembly of. Assembly from the Helmet Shell

Contents. Stainless Steel Side Block. 1.1 Separating the Side Block. Stainless Steel Side Block Reassembly of. Assembly from the Helmet Shell Separating the Side Block Assembly from the Helmet Shell Contents SSB-1 SSB-3 SSB-5 SSB-5 SSB-7 1.1 Separating the Side Block Assembly from the Helmet Shell 1.2 Side Block Assembly Replacement 1.3 Defogger

More information

ICE PROTECTION - PROPELLER

ICE PROTECTION - PROPELLER ICE PROTECTION - PROPELLER. DESCRIPTION This section describes the portion of the Ice Protection System pertaining to the propeller. This includes the slinger ring and the de-icing propeller boots. Grooved

More information

TABLE OF CONTENTS INTRODUCTION

TABLE OF CONTENTS INTRODUCTION R3 DISC MANUAL TABLE OF CONTENTS Introduction... 1 Frame Features... 2 Fork Preparation... 3 Small Parts... 5 Frame Preparation... 6 Brake Housing Installation... 7 Mechanical Cable Routing... 9 Electric

More information

E Manual Self tacking system 30

E Manual Self tacking system 30 597-205-E 2015-12-09 Manual Self tacking system 30 1 Self tacking system 30, 443-200-10 A self-tacking jib makes life on board a lot easier, in particular for shorthanded crews. The jib sheet is led to

More information

VK/VP SERIES : Sealless Vertical Pump. Assembling Instructions 2010

VK/VP SERIES : Sealless Vertical Pump. Assembling Instructions 2010 VK/VP SERIES : Sealless Vertical Pump Assembling Instructions 2010 20610 Manhattan Place Suite 116 Torrance, CA 90501 Phone: 310-328-9114 Fax: 310-328-9441 1. Motor Shaft and Pump Base (1) (2) Place a

More information