X5-55/X5-70/X5-80/X Operation Maintenance Installation Warranty Manual

Size: px
Start display at page:

Download "X5-55/X5-70/X5-80/X Operation Maintenance Installation Warranty Manual"

Transcription

1 X5-55/X5-70/X5-80/X5-105 Opertion Mintennce Instlltion Wrrnty Mnul

2 EU Complince Sttement Attwood Corportion hereby declres tht the MotorGuide X5 trolling motor is in complince with the essentil requirements nd other relevnt provisions of the 99/5/EC R&TTE directive. Council Directive 2004/108/EC Electromgnetic Comptibility EN 55012:2008; A1:2010 Vehicles, bots nd internl combustion engines. Council Directive 98/96/EC Mritime Equipment Directive EN 60945:2002+C1:2008 Mritime nvigtion nd rdiocommuniction equipment nd systems (Motor systems) CISPR16 Conducted nd Rdited Emissions EN :2008 ESD EN :2006 Rdited Immunity EN :2004 EFT EN :2005 Surges EN :2008 Conducted Susceptibility EN :2001 Mgnetic Field Immunity EN :2004 Voltge Dips nd Interrupts Council Directive 2006/42/EC Mchinery EN ISO Sfety of mchinery Generl principles for design, risk ssessment nd reduction i

3 Thnk You Thnk you for choosing MotorGuide, one of the finest trolling motors vilble. Yers of experience hve been committed to the gol of producing the finest qulity products. This led to MotorGuide's reputtion for strict qulity control, excellence, durbility, long lsting performnce nd being the best t providing fter the sle service nd support. Plese red this mnul crefully before operting your motor. This mnul hs been prepred to ssist you in the opertion, sfe use, nd cre of your trolling motor. Agin, thnk you for your confidence in MotorGuide. Wrrnty Messge The product you hve purchsed comes with Two Yer Limited Wrrnty from MotorGuide, the terms of the policy re set forth in the Wrrnty Informtion section of this mnul. The policy sttement contins description of the durtion of coverge, importnt disclimers nd limittions of dmges, nd other relted informtion. Plese review this importnt informtion. The description nd specifictions contined herein were in effect t the time this mnul ws pproved for printing. MotorGuide, whose policy is one of continued improvement, reserves the right to discontinue models t ny time, to chnge specifictions, designs, methods, or procedures without notice nd without incurring obligtion. Copyright nd Trdemrk Informtion MERCURY MARINE. All rights reserved. Reproduction in whole or in prt without permission is prohibited. Alph, Axius, Brvo One, Brvo Two, Brvo Three, Circle M with Wves Logo, K plnes, Mriner, MerCthode, MerCruiser, Mercury, Mercury with Wves Logo, Mercury Mrine, Mercury Precision Prts, Mercury Propellers, Mercury Rcing, MotorGuide, OptiMx, Quicksilver, SeCore, Skyhook, SmrtCrft, Sport Jet, Verdo, VesselView, Zero Effort, Zeus, #1 On the Wter nd We're Driven to win re registered trdemrks of Brunswick Corportion. Pro XS is trdemrk of Brunswick Corportion. Mercury Product Protection is registered service mrk of Brunswick Corportion. ii

4 Wrrnty Informtion MotorGuide Limited Two Yer Wrrnty... 1 Generl Informtion Boter's Responsibilities... 3 Protecting People in the Wter... 3 Pssenger Sfety Messge... 3 Sfe Boting Suggestions... 3 Product Overview X5 55/X5 70/X5 80/X5 105 MotorGuide Trolling Motor...5 Specifictions...6 Wiring nd Bttery Informtion Wiring nd Bttery Informtion... 7 Stndrd Prctices nd Procedures... 7 Bttery Recommendtions... 7 Bttery Precutions... 8 Estblishing Common Ground... 8 Wire nd Cble Routing...9 Wire Color Code Abbrevitions... 9 Bttery Connection Trolling Motor Instlltion nd Opertion Mount Brcket Instlltion Permnent Foot Pedl Mounting (Optionl) Instlling the Motor into the Bow Mount...17 Removing the Motor from the Bow Mount Connecting the Sonr Disply to the Trolling Motor Stowing the Trolling Motor Deploying the Trolling Motor Adjusting the Motor Depth Directionl Indictor Cble Steer Models Speed Control Cble Steer Models...24 iii

5 Mintennce Trolling Motor Cre Inspection nd Mintennce Schedule Lubriction Points Bttery Inspection Propeller Replcement Adjusting the Steering Cble Tension Front Locking Pin Replcement...30 MotorGuide Accessories Inquiries Troubleshooting Trolling Motor Performnce iv

6 WARRANTY INFORMATION MotorGuide Limited Two Yer Wrrnty KEEP YOUR ORIGINAL PURCHASE RECEIPT 1. To obtin wrrnty service, the purchser should deliver or return the unit (postge prepid nd insured) to ny MotorGuide uthorized service center. DO NOT RETURN TO PLACE OF PURCHASE unless they re n uthorized service center. Motors purchsed in other countries should be returned to plce of purchse. Products returned by mil should be crefully pckged nd include note describing the nture of the problem nd/or service requested, customer ddress, nd phone number. A copy of the receipt, Bill of Sle, registrtion verifiction, or other proof of purchse is required with the return of the product for wrrnty considertion. Wrrnty clims will not be ccepted without presenttion of purchse receipt for trolling motor, other verifiction of registrtion, or Bill of Sle for bot pckge. 2. MotorGuide electric trolling motors re wrrnted to the originl purchser to be free from defects in mteril nd/or workmnship for two (2) yers. Wrrnty is NOT trnsferble to ny subsequent purchser. 3. MotorGuide, t its discretion, will repir or replce items covered under the terms of this wrrnty. Neither MotorGuide nor MotorGuide service delers re responsible for dmges to MotorGuide products due to repirs performed by nyone other thn the MotorGuide Fctory Service Center. Neither MotorGuide nor Mercury Mrine is responsible for filure or dmge cused by improper instlltion, set up, preprtion, or previous service or repir errors. 4. Wrrnty coverge is vilble only to customers tht purchse from deler uthorized by MotorGuide/Mercury Mrine to distribute the product in the country in which the sle occurred. Wrrnty coverge nd durtion vries by the country in which the product resides. This wrrnty pplies to X5 series MotorGuide trolling motors sold nd residing in the United Sttes. This Limited Wrrnty begins on the dte the product is first sold to purchser or the dte on which the product is first put into service, whichever occurs first. MotorGuide ccessories re covered by this Limited Wrrnty for coverge period of one (1) yer from the dte of retil sle. The repir or replcement of prts, or the performnce of service under this wrrnty, does not extend the life of this wrrnty beyond its originl expirtion dte. Promotionl wrrnties re not included in this sttement nd coverge my vry by promotion. Product either sold or put into service more thn six yers from dte of mnufcture is excluded from wrrnty coverge. 5. MotorGuide Composite Shft Limited Lifetime Wrrnty. MotorGuide composite shfts re wrrnted to the originl retil purchser to be free of defects in mteril or workmnship for the lifetime of the originl purchser. MotorGuide will provide new composite shft t no cost for ny composite shft which contins defect in mteril or workmnship. The instlltion costs re the sole responsibility of the purchser. 1

7 WARRANTY INFORMATION 6. This wrrnty does not pply to norml worn prts, i.e., worn cbles, djustments, or product dmge due to 1) neglect, lck of mintennce, ccident, bnorml opertion or improper instlltion or service; 2) buse, i.e., bent metl columns, bent rmture shfts, broken control cbles, etc., ccidents, modifictions, misuse, excessive wer or dmge cused by n owner s filure to provide resonble nd necessry instlltion or cre; 3) use of n ccessory or prt not mnufctured by MotorGuide/ Mercury; 4) ltertion or removl of prts; 5) opening the lower unit (motor) by nyone other thn the Fctory Service Center will void this wrrnty. 7. This wrrnty will not pply to hul out, lunch, towing nd storge, trnsporttion chrges nd/or trvel time, telephone or rentl chrges of ny type, inconvenience, or loss of time or income, or other consequentil dmges. 8. We reserve the right to improve the design of ny trolling motor without ssuming ny obligtion to modify ny trolling motor previously mnufctured. 9. Serilized "Service Repir" motors hve one (1) yer wrrnty. Nonserilized "Service Repir" electric trolling motors re NOT wrrnted. "Service Repir" motor denotes trolling motor sold by MotorGuide tht my be "used," but hs been inspected nd my hve hd minor repirs. Originl retil purchser of "Service Repir" motor is the first purchser of the motor fter it is denoted s "Service Repir." "Service Repir" motors hve blue sticker on the bttery cble nd box denoting "Mnufcturer Certified Service Repir Motor." 10. TERMINATION OF COVERAGE: Wrrnty coverge my be terminted for repossessed product, or product purchsed t uction, from slvge yrd, from liquidtor, from n insurnce compny, from unuthorized mrine delers or botbuilders, or other third prty entities. 11. ALL INCIDENTAL AND/OR CONSEQUENTIAL DAMAGES ARE EXCLUDED FROM THIS WARRANTY, WARRANTIES OF MERCHANTABILITY AND FITNESS ARE EXCLUDED FROM THIS WARRANTY, IMPLIED WARRANTIES ARE LIMITED TO THE LIFE OF THIS WARRANTY, SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE. 2

8 Boter's Responsibilities The opertor (driver) is responsible for the correct nd sfe opertion of the bot nd sfety of its occupnts nd generl public. It is strongly recommended tht ech opertor (driver) red nd understnd this entire mnul before operting the trolling motor. Be sure t lest one dditionl person on bord is instructed in the bsic opertion of the trolling motor in cse the driver is unble to operte the bot. Protecting People in the Wter WHILE YOU ARE TROLLING GENERAL INFORMATION It is very difficult for person in the wter to tke quick ction to void bot heding in their direction, even t slow speeds Alwys slow down nd exercise extreme cution ny time you re boting in n re where there might be people in the wter. WHILE THE BOAT IS STATIONARY! WARNING A spinning propeller, moving bot, or ny solid device ttched to the bot cn cuse serious injury or deth to swimmers. Stop the trolling motor immeditely whenever nyone in the wter is ner your bot. Shut off the trolling motor before llowing people to swim or be in the wter ner your bot. Pssenger Sfety Messge Whenever the bot is in motion, observe the loction of ll pssengers. A sudden reduction in bot speed, such s shrp chnge of bot direction, could throw them off the bot. Sfe Boting Suggestions In order to sfely enjoy the wterwys, fmilirize yourself with locl nd other governmentl boting regultions nd restrictions, nd consider the following suggestions. Use flottion devices. It is the lw to hve n pproved personl flottion device of suitble size for ech person bord nd hve it redily ccessible. 3

9 GENERAL INFORMATION Do not overlod your bot. Most bots re rted nd certified for mximum lod (weight) cpcities, refer to your bot cpcity plte. If in doubt, contct your deler or the bot's mnufcturer. Perform sfety checks nd required mintennce. Follow regulr schedule nd ensure ll repirs re mde properly. Never be under the influence of lcohol or drugs while boting (it is the lw). Alcohol or drug use impirs your judgment nd gretly reduces your bility to rect quickly. Pssenger bording. Stop the trolling motor whenever pssengers re bording or unloding. Be lert. The opertor of the bot is responsible by lw to mintin proper lookout by sight nd hering. The opertor must hve n unobstructed view prticulrly to the front. No pssengers, lod, or fishing sets should block the opertors view when operting the bot. Underwter hzrds. Reduce speed nd proceed with cution whenever nvigting in shllow wter. Tripping hzrds. To void trip hzrd, route ll cbles nd wiring netly nd out of the wy. Report ccidents. Bot opertors re required by lw to file Boting Accident Report with their stte boting lw enforcement gency when their bot is involved in certin boting ccidents. A boting ccident must be reported if 1) there is loss of life or probble loss of life, 2) there is personl injury requiring medicl tretment beyond first id, 3) there is dmge to bots or other property where the dmge or 4) there is complete loss of the bot. Seek further ssistnce from locl lw enforcement. 4

10 PRODUCT OVERVIEW X5 55/X5 70/X5 80/X5 105 MotorGuide Trolling Motor m b c d l h g e k i f j Directionl indictor b cm (21 in.) mount brcket c - Ltch relese hndle d - Foot pedl e - Momentry button f - 3 position switch g - Speed control knob h - Bttery cbles i - 61 cm (24 in.) mount brcket (optionl) j - Propeller k - Lower unit l - Composite column m - Brcket door knob 5

11 PRODUCT OVERVIEW Specifictions Model Freshwter/ Sltwter Volts Speeds Forwrd/ Reverse Sonr Pek Thrust Shft Length X5 55 FW Freshwter 12 V Vrible No 24.9 kgf (55 lbf) cm (45 in.) X5 55 FW Freshwter 12 V Vrible Yes 24.9 kgf (55 lbf) cm (45 in.) X5 70 FW Freshwter 24 V Vrible No 31.8 kgf (70 lbf) cm (45 in.) X5 70 FW Freshwter 24 V Vrible Yes 31.8 kgf (70 lbf) cm (45 in.) X5 80 FW Freshwter 24 V Vrible No 36.3 kgf (80 lbf) 91.4 cm (36 in.) X5 80 FW Freshwter 24 V Vrible No 36.3 kgf (80 lbf) cm (45 in.) X5 80 FW Freshwter 24 V Vrible Yes 36.3 kgf (80 lbf) cm (45 in.) X5 80 FW Freshwter 24 V Vrible No 36.3 kgf (80 lbf) cm (50 in.) X5 80 FW Freshwter 24 V Vrible Yes 36.3 kgf (80 lbf) cm (50 in.) X5 80 FW Freshwter 24 V Vrible No 36.3 kgf (80 lbf) cm (60 in.) X5 80 FW Freshwter 24 V Vrible Yes 36.3 kgf (80 lbf) cm (60 in.) X5 105 FW Freshwter 36 V Vrible No 47.6 kgf (105 lbf) cm (45 in.) X5 105 FW Freshwter 36 V Vrible Yes 47.6 kgf (105 lbf) cm (45 in.) X5 105 FW Freshwter 36 V Vrible No 47.6 kgf (105 lbf) cm (50 in.) X5 105 FW Freshwter 36 V Vrible Yes 47.6 kgf (105 lbf) cm (50 in.) X5 105 FW Freshwter 36 V Vrible No 47.6 kgf (105 lbf) cm (60 in.) X5 105 FW Freshwter 36 V Vrible Yes 47.6 kgf (105 lbf) cm (60 in.) 6

12 WIRING AND BATTERY INFORMATION Wiring nd Bttery Informtion! WARNING An operting or chrging bttery produces gs tht cn ignite nd explode, sprying out sulfuric cid, which cn cuse severe burns. Ventilte the re round the bttery nd wer protective equipment when hndling or servicing btteries.! WARNING Performing service or mintennce without first disconnecting the bttery cn cuse product dmge, personl injury, or deth due to fire, explosion, electricl shock, or unexpected motor strting. Alwys disconnect the bttery cbles from the bttery before mintining, servicing, instlling, or removing motor components. Stndrd Prctices nd Procedures When instlling or removing this trolling motor, follow these guidelines: Disconnect the trolling motor from the trolling motor bttery. Do not use the min engine bttery to power the trolling motor. Bttery Recommendtions Use 12 volt, deep cycle mrine btteries. The number of btteries required vries ccording to the model of your trolling motor. Refer to Bttery Connection. As generl rule, deep cycle btteries with higher mp hour rting or reserve cpcity rting will provide longer run times nd better performnce. Instll mnul reset circuit breker in line with the trolling motor positive leds within 180 cm (72 in.) of the btteries. These cn be purchsed from your locl MotorGuide retiler or from Do not extend the included 10 guge bttery cbles more thn 1.8 m (6 ft) for totl of 3 m (10 ft). If longer bttery cbles re required, MotorGuide offers ccessory 8 mm² (8 guge) bttery cbles. Use nylock nuts to secure the bttery cbles to their terminls. Using wing nuts to secure the bttery cbles cn cuse loose connections. Any depth sounders or fish finders must be powered from the engine strting bttery. Connecting electronic equipment to the trolling motor btteries cn cuse electricl interference nd possible electrolysis. Recommended MotorGuide Accessory Description 8 guge bttery cble nd terminls with 50 mp mnul reset circuit breker Prt Number MM309922T 7

13 WIRING AND BATTERY INFORMATION Recommended MotorGuide Accessory Description 50 mp mnul reset circuit breker 60 mp mnul reset circuit breker Prt Number MM5870 8M Bttery Precutions! WARNING An operting or chrging bttery produces gs tht cn ignite nd explode, sprying out sulfuric cid, which cn cuse severe burns. Ventilte the re round the bttery nd wer protective equipment when hndling or servicing btteries. When chrging btteries, n explosive gs mixture forms in ech cell. Prt of this gs escpes through holes in the vent plugs nd my form n explosive tmosphere round the bttery if ventiltion is poor. This explosive gs my remin in or round the bttery for severl hours fter it hs been chrged. Sprks or flmes cn ignite this gs nd cuse n internl explosion, which my shtter the bttery. The following precutions should be observed to prevent n explosion: 1. Do not smoke ner btteries being chrged or which hve been chrged very recently. 2. Do not brek live circuits t terminls of btteries, becuse sprk usully occurs t the point where live circuit is broken. Alwys be creful when connecting or disconnecting cble clmps on chrgers. Poor connections re common cuse of electricl rcs which cuse explosions. 3. Do not reverse polrity of bttery terminl to cble connections. Estblishing Common Ground A common ground ( ) connection increses sonr sensitivity, improves sonr disply, voids the ground circuit s possible source of corrosion or electrolysis, nd reduces interference with other electronic equipment. For 12 volt trolling motor pplictions, connect the negtive ( ) terminl on the trolling motor bttery to the negtive ( ) terminl on the engine strting bttery with common ground cble to estblish common ground. For 24 volt nd 36 volt trolling motors, common ground ( ) connection cnnot be estblished with the 12 volt electricl system in the bot due to the different circuit voltges. As generl rule to reduce interference with other electronics on your bot, route ll bttery wiring wy from other bot wiring (opposite side of the bot if possible), keep the bttery cble length s short s possible, nd lwys use bttery cbles of the pproprite size (guge). 8

14 WIRING AND BATTERY INFORMATION ELECTROLYSIS Using the min engine bttery s power source for the trolling motor my cuse electrolysis on metllic prts. If the motor nd bttery wiring re instlled correctly nd electrolysis issues continue, seprte the trolling motor from ny other bot electronics. Using the min engine bttery s power source for the trolling motor is not recommended. Refer to Bttery Connection for correct instlltion. Wire nd Cble Routing Route the trolling motor wires on the opposite side of the bot from other bot wiring. The trolling motor should be connected to its own dedicted bttery. Sensitive electronics, such s depth finders, should be connected to seprte bttery. Mrine engines should hve their own dedicted strting bttery. All btteries should hve common ground. Wire Color Code Abbrevitions Wire Color Abbrevitions BLK Blck BLU Blue BRN Brown GRY or GRA Gry GRN Green ORN or ORG Ornge PNK Pink PPL or PUR Purple RED Red TAN Tn WHT White YEL Yellow LT or LIT Light DK or DRK Drk 9

15 WIRING AND BATTERY INFORMATION Bttery Connection! WARNING Before working round electricl system components, disconnect the bttery cbles from the bttery to prevent injury or dmge to the electricl system due to n ccidentl short circuit.! CAUTION Disconnecting or connecting the bttery cbles in the incorrect order cn cuse injury from electricl shock or cn dmge the electricl system. Alwys disconnect the negtive ( ) bttery cble first nd connect it lst. NOTICE Filure to operte the trolling motor within the recommended voltge specifictions cn cuse product dmge. Do not exceed the mximum supply voltge. IMPORTANT: Refer to the decl on the hed of the trolling motor to determine the voltge requirements of your trolling motor. 12-VOLT BATTERY CONNECTION 1. Strting with the negtive ( ) led, disconnect the bttery cbles from the engine strting bttery. 2. Instll 50 mp (good) or 60 mp (best) mnul reset circuit breker in line with the trolling motor power cble positive (+) led nd the trolling motor bttery positive (+) terminl. 3. Connect the positive (+) trolling motor led to the positive (+) trolling motor bttery terminl. 4. Connect the negtive ( ) trolling motor led to the negtive ( ) trolling motor bttery terminl. 5. Connect jumper cble (common ground bond) from the trolling motor bttery negtive ( ) terminl to the engine bttery negtive ( ) terminl. NOTE: Vessels using 12 volt trolling motors with multiple btteries must hve common ground bonding circuit. Not estblishing common ground between the vessel btteries my cuse severe corrosion, electrolysis, or electricl shock. NOTE: The common ground bond cble should be no more thn one wire size (guge) smller thn the bttery cbles, nor smller thn 16 guge (AWG). The common ground bond cble must be insulted, nd secured to the negtive ( ) bttery terminls with ring style connectors. 10

16 WIRING AND BATTERY INFORMATION 6. Strting with the positive (+) led, reconnect the bttery cbles to the engine strting bttery. e BLK RED RED BLK b c d f volt bttery connection with common ground bond - Power cbles to trolling motor b - Mnul reset circuit breker c - Trolling motor bttery d - Engine strting bttery e - Power cbles to engine f - Common ground ( ) bond cble 24-VOLT BATTERY CONNECTION 1. Strting with the negtive ( ) led, disconnect the bttery cbles from the engine strting bttery. 2. Instll 50 mp (good) or 60 mp (best) mnul reset circuit breker in line with the trolling motor power cble positive (+) led nd the trolling motor bttery B positive (+) terminl. 3. Connect the positive (+) trolling motor led to the positive (+) terminl on trolling motor bttery B. 4. Connect jumper wire (reference gry) between the negtive ( ) terminl on bttery B to the positive (+) terminl on bttery A. IMPORTANT: The jumper wire should be the sme wire guge s the negtive ( ) nd positive (+) power cbles. 5. Connect the trolling motor negtive ( ) led to the negtive ( ) terminl on bttery A. 11

17 WIRING AND BATTERY INFORMATION 6. Strting with the positive (+) led, reconnect the bttery cbles to the engine strting bttery. d BLACK GRAY Bttery A c RED Bttery B c b volt bttery connection - Power cbles to trolling motor b - Mnul reset circuit breker c - Jumper wire (not supplied) d - Negtive ( ) bttery terminl IMPORTANT: Do not connect common ground bond cble between 24 volt nd 12 volt electricl circuits. 36-VOLT BATTERY CONNECTION 1. Strting with the negtive ( ) led, disconnect the bttery cbles from the engine strting bttery. 2. Instll 50 mp (good) or 60 mp (best) mnul reset circuit breker in line with the trolling motor power cble positive (+) led nd the trolling motor bttery C positive (+) terminl. 3. Connect the positive (+) trolling motor led to the positive (+) terminl on trolling motor bttery C. 4. Connect jumper wire (reference gry) between the negtive ( ) terminl on bttery C to the positive (+) terminl on bttery B. IMPORTANT: The jumper wire should be the sme wire guge s the negtive ( ) nd positive (+) power cbles. 5. Connect jumper wire (reference gry) between the negtive ( ) terminl on bttery B to the positive (+) terminl on bttery A. 12

18 WIRING AND BATTERY INFORMATION 6. Connect the trolling motor negtive ( ) led to the negtive ( ) terminl on bttery A. 7. Strting with the positive (+) led, reconnect the bttery cbles to the engine strting bttery. d BLK GRY Bttery A c GRY Bttery B c RED Bttery C c b volt bttery connection - Power cbles to trolling motor b - Mnul reset circuit breker c - Jumper wire (not supplied) d - Negtive ( ) bttery terminl IMPORTANT: Do not connect common ground bond cble between 36 volt nd 12 volt electricl circuits. 13

19 TROLLING MOTOR INSTALLATION AND OPERATION Mount Brcket Instlltion b c X5 bow mount brcket b - Ltch relese hndle c - Brcket door knob 1. Select n pproprite re on the deck of the bot to instll the mount. Ensure tht the forwrd mounting screws will not penetrte the hull. IMPORTANT: Choose n re on the bot deck tht llows 7.6 cm (3 in.) clernce between the bow of the bot nd the column of the trolling motor Clernce 7.6 cm (3.0 in.) 2. Plce the bow mount bse on the surfce of the bot deck. Use the mount bse s templte to mrk the loctions of the front mounting holes nd the rer mounting holes on the mount bse. 14

20 TROLLING MOTOR INSTALLATION AND OPERATION IMPORTANT: A minimum of four mounting bolts re required to mount the trolling motor to the bot. Spred the mounting bolts s fr prt s prcticl for the most secure mounting Mount brcket mounting holes (5 per side) 3. Drill the mounting holes with 7 mm (1/4 in.) dimeter drill bit. Remove ny debris. IMPORTANT: Use lrger drill bit to countersink the holes on fiberglss bots to prevent crcking. 4. Insert the rubber isoltors between the bse of the mount nd the bot mounting surfce. Plce the tie down strp under the mount brcket, hook nd loop side down, with the buckle fcing towrd the outside of the bot. b Velcro tie down strp b - Buckle 15

21 TROLLING MOTOR INSTALLATION AND OPERATION 5. Instll the stinless steel wshers nd nylon locknuts onto the mounting screws underneth the bot deck. Tighten them securely with P3 screwdriver nd 7/16 in. wrench. IMPORTANT: If necessry, shim the rubber wshers with 25 mm (1 in.) outside dimeter stinless steel wshers to crete level mounting surfce. IMPORTANT: The mount brcket must ly flush ginst the rubber isoltors before being bolted to the deck or the mount will bind, mking it difficult or impossible to unltch. c b - Mount brcket b - Mounting screw c - Rubber isoltor d - Deck e - Wsher f - Nylon locknut d e f Once instlled, the brcket should fsten securely nd evenly, with the ltch pins in the slots, nd relese with light, quick pull on the rope hndle. Permnent Foot Pedl Mounting (Optionl) 1. Determine suitble loction for the foot pedl with the trolling motor deployed nd in the stowed position. Ensure tht there re no obstructions beneth the bot deck tht would interfere with the mounting screws, such s bulkheds or bot wiring. 2. Once suitble loction is chosen, mrk the mounting holes, using the foot pedl s templte. 3. Use 3 mm (7/64 in.) drill bit to drill holes through the bot deck. 16

22 TROLLING MOTOR INSTALLATION AND OPERATION 4. Use four #8 x 2 in. stinless steel screws to secure the foot pedl to the bot deck Instlling the Motor into the Bow Mount 1. Turn the brcket door knob counterclockwise to loosen nd open the brcket door. 2. Plce the motor column into the brcket nd close the door. 3. Turn the brcket door knob clockwise to tighten the motor column in the brcket. - Brcket door knob b - Brcket door b Removing the Motor from the Bow Mount 1. Turn the brcket door knob counterclockwise to loosen nd open the brcket door. 2. Remove the motor column from the brcket nd close the door. 17

23 TROLLING MOTOR INSTALLATION AND OPERATION Connecting the Sonr Disply to the Trolling Motor NOTE: This procedure pplies only to models equipped with integrted sonr. This sonr disply connection procedure pplies to trolling motor models with internl sonr tht offer built in 200/83 khz sonr trnsducers comptible with Egle, Grmin, Humminbird, Lowrnce, nd Vexilr brnd sonr displys. For comptibility with other sonr units, refer to The trolling motor is equipped with Lowrnce 7 pin plug. Adpters re vilble to connect other brnds of sonr displys to the trolling motor. Mtch the cble connector to the sonr port on the bck of the sonr disply. Power up the unit to ensure tht the sonr cble is connected securely. b - Hrness to nose cone sonr b - Lowrnce 7 pin plug to sonr disply Trnsducer dpter cbles vilble from MotorGuide Lowrnce 7 to 6 pin dpter Vexilr 3 pin dpter Grmin 6 pin dpter Humminbird 7 pin dpter Prt Number 8M M M M Stowing the Trolling Motor! WARNING Rotting propellers cn cuse serious injury or deth. Never strt or operte the motor out of wter.! CAUTION Moving prts, such s hinges nd pivot points, cn cuse serious injury. Keep wy from moving prts when stowing, deploying, or tilting the motor. 1. Firmly grsp the ltch relese hndle. 2. Snp the ltch relese hndle to disengge the lock pin. 18

24 TROLLING MOTOR INSTALLATION AND OPERATION 3. Continue to pull the ltch relese hndle to rise the lower unit onto the mount. - Ltch relese hndle IMPORTANT: Gently rise the trolling motor out of the wter. Do not relese the ltch relese hndle until the lock pin is engged. 4. Once the motor is in the stowed position, the lock pin engges to secure the trolling motor X5 in the stowed position 19

25 TROLLING MOTOR INSTALLATION AND OPERATION 5. Position the tie down strp over the composite column nd through the buckle. Pull it tight, then secure the hook nd loop bcking together to secure the motor to the mount brcket. - Tie down strp Deploying the Trolling Motor! WARNING Rotting propellers cn cuse serious injury or deth. Never strt or operte the motor out of wter.! CAUTION Moving prts, such s hinges nd pivot points, cn cuse serious injury. Keep wy from moving prts when stowing, deploying, or tilting the motor.! CAUTION Avoid possible serious injury from the motor dropping suddenly when djusting the motor depth. Firmly grsp the motor shft with one hnd when rising or lowering the motor. 1. Remove the tie down strp securing the trolling motor to the mount brcket. 2. Firmly grsp the ltch relese hndle. 3. Snp the ltch relese hndle to disengge the lock pin. 4. Continue to mintin tension on the ltch relese hndle while lowering the trolling motor into the wter. 20

26 TROLLING MOTOR INSTALLATION AND OPERATION IMPORTANT: Gently lower the trolling motor into the wter. Do not relese the ltch relese hndle until the lock pin is engged. - Ltch relese hndle Once the motor is in the deployed position, the lock pin will engge to secure the trolling motor. - X5 in the deployed position Adjusting the Motor Depth! CAUTION Avoid possible serious injury from dropping the motor when djusting the motor depth. Firmly grsp the motor shft with one hnd when rising or lowering the motor. 21

27 TROLLING MOTOR INSTALLATION AND OPERATION CABLE STEER MODELS Adjust the depth of the motor to improve trolling motor performnce in vrious wter depths nd wve conditions. IMPORTANT: When djusting the motor depth, ensure tht the propeller bldes re fully submerged cm (6 12 in.) below the wter surfce to void ventiltion. 1. Firmly grsp the column with one hnd. 2. Loosen the brcket door knob until the motor column slides freely. 3. Rise or lower the motor column until the propeller bldes re submerged cm (6 12 in.) below the wter surfce, then tighten the collr. 4. Adjust the brekwy knobs on ech side of the mount so the motor will brek wy if it encounters underwter obstructions. b b - Brcket door knob b - Brekwy knobs

28 TROLLING MOTOR INSTALLATION AND OPERATION Directionl Indictor Cble Steer Models The indictor provides directionl informtion t glnce. b c d Directionl indictor b - Right turn toe down; motor steers bot to right (continue to press ll the wy down for reverse) c - Stright hed foot pedl in middle d - Left turn heel down; motor steers bot to left (continue to press ll the wy down for reverse) 23

29 TROLLING MOTOR INSTALLATION AND OPERATION Speed Control Cble Steer Models DIGITAL VARIABLE SPEED MOTORS Foot operted motors re vilble with digitl vrible speed control. Control the speed of your motor by rolling the speed control knob with your hnd or foot until you rech the desired speed. b c d Foot pedl b - Momentry switch c - On/off/pedl switch d - Speed control knob Speed control knob: Digitl vrible speed motor control knobs re numbered 0 10, nd llow you to select ny speed from 0 10, nd stop the motor. Momentry switch: The momentry switch is locted on the top right corner of the foot pedl. The momentry switch works in conjunction with the on/off/pedl switch when it is in the pedl position. When the momentry switch is pressed, the motor will run t the selected speed s long s the switch is pressed. On/off/pedl switch: This three position switch provides three options for operting the motor: on, pedl, or off.. On: Allows the motor to run continuously t the speed selected by the speed control knob, without the use of the momentry switch. b. Pedl: Allows the motor to ctivte with the momentry switch t the speed selected by the speed control knob. c. Off: Turns the trolling motor off. 24

30 Trolling Motor Cre To keep your trolling motor in the best operting condition nd retin its dependbility, it is importnt tht your trolling motor receive periodic inspections nd mintennce. We urge you to keep it mintined properly to ensure the sfety of you nd your pssengers.! WARNING Neglecting to inspect, mintin, or repir your trolling motor cn result in product dmge or serious injury or deth. Do not perform mintennce or service on your trolling motor if you re not fmilir with the correct service nd sfety procedures. SELECTING REPLACEMENT PARTS We recommend using originl MotorGuide Certified Tough replcement prts. Inspection nd Mintennce Schedule BEFORE EACH USE Check the trolling motor for tightness on the deck mount. Check the tightness of the bttery led connections. Visully inspect for loose or corroded wiring connections. Check the tightness of the propeller nut. Check the propeller bldes for dmge. AFTER EACH USE Disconnect the bttery cbles from the power source. Check the propeller nd the propeller shft for debris such s weeds nd fishing line. Remove ll debris. Rinse the trolling motor with clen wter to remove dirt nd dust tht my scrtch the surfce. EVERY 100 HOURS OF USE OR ANNUALLY Periodiclly lubricte ll the pivot points. Refer to Lubriction Points. Check the tightness of bolts, nuts, nd other fsteners. Inspect the bttery. Refer to Bttery Inspection. STORAGE PREPARATION MAINTENANCE The mjor considertion in prepring the trolling motor for storge is to protect it from corrosion nd dmge cused by freezing of trpped wter. Complete the pproprite cre instructions to prepre the trolling motor for storge. Store the trolling motor in dry loction where it will not be ffected by tempertures below 29 C ( 20 F). 25

31 IMPORTANT: Trolling motors stored in tempertures below 0 C (32 F) should be operted slowly for minimum of 15 minutes before going bove 30% opertion. Lubriction Points NOTE: Preferred lubricnts cn be obtined t ny uthorized MotorGuide or Mercury Mrine service center. To reduce friction nd quiet squeks, lubricte the specified loctions periodiclly with the following lubricnts: Brcket door knob threds 2 4 C with PTFE Ltch pin hooks 2 4 C with PTFE Ltch pins 2 4 C with PTFE MAINTENANCE Pivot pins 4 Stroke 10W 30 Outbord Oil IMPORTANT: Never use n erosol lubricnt to grese or oil ny prt of the unit. Mny erosol lubricnts contin hrmful propellnts tht cn cuse dmge to vrious prts of the trolling motor. IMPORTANT: Do not llow ny lubricnt to contct the column sleeves in the door brcket hlves s trolling motor steering tension will be ffected. c c b d c c b Ltch pin hooks b - Pivot pins c - Ltch pins d - Brcket door knob threds Tube Ref No C with PTFE 110 Description Where Used Prt No. 4-Stroke 10W-30 Outbord Oil Bttery Inspection Ltch pins, ltch pin hooks, nd brcket door knob threds A 1 Pivot pins 92-8M The bttery should be inspected t periodic intervls to ensure proper trolling motor opertion. 26

32 IMPORTANT: Red the sfety nd mintennce instructions which ccompny your bttery. 1. Ensure tht the bttery is secured to the vessel. 2. Ensure tht the bttery cble terminls re clen, tight, nd correctly instlled. For instlltion instructions, refer to Bttery Connection. 3. Ensure tht the bttery is equipped with bttery box to prevent ccidentl shorting of the bttery terminls. Propeller Replcement! WARNING Performing service or mintennce without first disconnecting the bttery cn cuse product dmge, personl injury, or deth due to fire, explosion, electricl shock, or unexpected motor strting. Alwys disconnect the bttery cbles from the bttery before mintining, servicing, instlling, or removing motor components. REMOVING THE PROPELLER MAINTENANCE 1. Disconnect the power cbles from the bttery. 2. While holding the propeller blde with one gloved hnd, use 9/16 in. wrench or rtchet nd 9/16 in. socket to remove the propeller nut. Remove the propeller nut nd wsher (or node, for sltwter models). IMPORTANT: Remove the propeller nut with wrench or rtchet nd socket. Using nother tool my dmge the propeller nut or shft. If the propeller cnnot be removed esily, use rubber mllet to lightly tp the bck side of the opposite blde. If the propeller cnnot be removed, hve the propeller removed by n uthorized deler. 27

33 MAINTENANCE NOTE: If the propeller pin is bent, replce the propeller pin INSTALLING THE PROPELLER 1. Rotte the motor shft to insert the propeller pin horizontlly. - Propeller pin

34 MAINTENANCE 2. Instll the propeller onto the motor shft by engging the propeller onto the propeller pin Instll the wsher (or node, for sltwter models) onto the propeller shft, then instll the propeller nut. Use wrench or socket nd rtchet to tighten the propeller nut until it is snug, then tighten the nut nother 1/4 turn. IMPORTANT: Do not overtighten the propeller nut, or dmge to the propeller or propeller pin my occur Adjusting the Steering Cble Tension! WARNING Neglecting to inspect, mintin, or repir your trolling motor cn result in product dmge or serious injury or deth. Do not perform mintennce or service on your trolling motor if you re not fmilir with the correct service nd sfety procedures. The cble tension on the X5 trolling motor is preset t the fctory. With time nd use, the cbles my stretch slightly, requiring occsionl djustment. The following procedure explins how to djust the steering cble tension. Use cre while djusting the steering cble tension. Excessive cble tension will cuse premture wer to the cbles nd pulleys, while excessively loose tension my cuse the cbles to jump off of the pulleys, resulting in loss of steering control. 29

35 MAINTENANCE 1. Remove the foot pedl from the bot deck if it hs been secured with screws. 2. Adjust the cble tension by turning the cble tension screw clockwise to increse tension, nd counterclockwise to decrese tension. Adjust the cble tension screw to the specified torque vlue. Description Nm lb in. lb ft Cble tension screw Bottom of foot pedl - Cble tension screw Front Locking Pin Replcement The front locking pin cn be esily replced if the locking pin is dmged. Refer to the following instructions nd follow them completely for successful repir.! WARNING Performing service or mintennce without first disconnecting the bttery cn cuse product dmge, personl injury, or deth due to fire, explosion, electricl shock, or unexpected motor strting. Alwys disconnect the bttery cbles from the bttery before mintining, servicing, instlling, or removing motor components. 1. Pull the ltch relese hndle nd open the mount to position where it is prt wy between the stowed nd deployed positions. Support the mount in this position. 2. Pull nd hold the ltch relese hndle until the lock is ligned s shown. Hold the ltch relese hndle in this position. 30

36 MAINTENANCE IMPORTANT: Do not relese the ltch relese hndle until the new locking pin is instlled, or internl dmge to the mount will occur. - Locking pin b - Lock b Once the lock is ligned s shown, press the locking pin in the direction indicted, but do not remove it completely. NOTE: If required, tp the locking pin out with screwdriver hndle or smll hmmer to disengge the locking pin Continue to hold the ltch relese hndle once the locking pin is prtilly removed. 5. Orient the new locking pin so the lignment tb is fcing the sme direction s the lignment tb of the old locking pin. 6. Press the new locking pin into the opposite side of the mount. Continue to press the new locking pin until it clicks into position. 31

37 MAINTENANCE NOTE: The new locking pin will press out the old locking pin s it is instlled. - Alignment tbs Relese the ltch relese hndle nd move the trolling motor to the stowed or deployed position s desired. 32

38 Trolling Motor Performnce Symptom Possible Cuse Resolution Loss of power Excessive noise, vibrtion Motor filure (ll speeds) Motor filure (one or more speeds) TROUBLESHOOTING Wek bttery Loose or corroded bttery connections Propeller is loose, dmged, or off blnce Wiring or electricl connection fulty Weeds, fishing line, or debris wrpped round propeller Motor shft is bent Propeller is loose, dmged, or off blnce Wek bttery Loose or corroded bttery connections Electricl Fuse or circuit breker is open Propeller is loose, dmged, or off blnce Wiring or electricl connection fulty. Refer to Wiring nd Bttery Informtion. Refer to Mintennce. Wire guge from the bttery to the trolling motor is insufficient. Six guge wire (13 mm²) is recommended. Remove weeds, fishing line, or debris from propeller. Refer to Wrrnty Informtion. Refer to Mintennce. Refer to Wiring nd Bttery Informtion. Check the connector for loose or dmged connection. Refer to Wiring nd Bttery Informtion. Locte nd correct the cuse of the overlod. Then replce the fuse or reset the circuit breker. Refer to Mintennce. Refer to Wrrnty Informtion. 33

39 TROUBLESHOOTING Symptom Possible Cuse Resolution Difficulty removing propeller Mount brcket squeks Bent propeller pin Bent rmture shft Lock pins need lubriction Hold one blde nd lightly tp the opposite blde with rubber mllet. Use putty knife on both sides of the propeller to pply equl pressure. Refer to service center. Lubricte the lock pins on the mount brcket with 2 4 C with PTFE. 34

Operation Maintenance Installation Warranty Manual

Operation Maintenance Installation Warranty Manual 2017 Mercury Mrine Xi5 Wireless Edition Opertion Mintennce Instlltion Wrrnty Mnul 8M0124200 117 eng eng ORIGINAL LANGUAGE INSTRUCTIONS FCC nd IC Complince Sttement Xi5 WIRELESS FOOT PEDAL FCC ID MVU09291

More information

90-8M eng. Xi5 Wireless Edition Mercury Marine

90-8M eng. Xi5 Wireless Edition Mercury Marine 2014 Mercury Mrine Xi5 Wireless Edition eng 90-8M0097265 814 eng ORIGINAL LANGUAGE INSTRUCTIONS FCC nd IC Complince Sttement Xi5 WIRELESS FOOT PEDAL FCC ID MVU09291 Xi5 WIRELESS REMOTE FCC ID MVU09305

More information

2017 Mercury Marine. Xi3 Wireless Edition. Operation Maintenance Installation Warranty Manual

2017 Mercury Marine. Xi3 Wireless Edition. Operation Maintenance Installation Warranty Manual 2017 Mercury Mrine Xi3 Wireless Edition Opertion Mintennce Instlltion Wrrnty Mnul 8M0130831 1117 eng eng ORIGINAL LANGUAGE INSTRUCTIONS FCC nd IC Complince Sttement Xi SERIES WIRELESS FOOT PEDAL FCC ID

More information

Operation Maintenance Installation Warranty Manual

Operation Maintenance Installation Warranty Manual Opertion Mintennce Instlltion Wrrnty Mnul 2017 Mercury Mrine Xi3 Wireless Edition ORIGINAL LANGUAGE INSTRUCTIONS FCC nd IC Complince Sttement Xi SERIES WIRELESS FOOT PEDAL FCC ID MVU09291 Xi SERIES WIRELESS

More information

Reproduction. Not for. Mower - Roller Bar WARNING. Installation and Leveling Instructions. Attention Setup Personnel: Model: ,

Reproduction. Not for. Mower - Roller Bar WARNING. Installation and Leveling Instructions. Attention Setup Personnel: Model: , Mower - Roller Br Instlltion nd Leveling Instructions 4 Model: 9555, 9594 Attention Setup Personnel: 5 4 5 Model: 958, 9595 Model: 9559 Model: 959 The sfety wrnings provided in this guide nd in the trctor's

More information

ANATOMY OF A TRIPOD: Friction Lock (column) 8 Boots / Footwear. Friction Lock (Leg)

ANATOMY OF A TRIPOD: Friction Lock (column) 8 Boots / Footwear. Friction Lock (Leg) IMPORTANT DO NOT USE YOUR TRIPOD UNTIL YOU HAVE READ THESE INSTRUCTIONS. NO WARRANTY CLAIM WILL BE ENTERED INTO FOR THE MISUSE OR INCORRECT USE OF THESE PRODUCTS. ANATOMY OF A TRIPOD: We offer the three

More information

Pinpoint GPS. FCC and IC Compliance Statement

Pinpoint GPS. FCC and IC Compliance Statement FCC nd IC Complince Sttement PINPOINT KEY FOB, FCC ID MVU10148 ACMA: N2523 IC: 6094A 09291, 6094A 09305 This device complies with prt 15 of the FCC Rules. Opertion is suject to the following two conditions:

More information

Pinpoint GPS 90-8M

Pinpoint GPS 90-8M FCC nd IC Complince Sttement PINPOINT KEY FOB, FCC ID MVU10148 ACMA: N2523 IC: 6094A 09291, 6094A 09305 This device complies with prt 15 of the FCC Rules. Opertion is suject to the following two conditions:

More information

Workfit -SR, Dual Monitor Short Surface

Workfit -SR, Dual Monitor Short Surface User's Guide Workfit -SR, Dul Monitor Short Surfce Do not throw wy! Crdord locks needed for instlltion. Visit http://www.ergotron.com/workfi t-sr-instll for instlltion instructionl video. NOTE: 10 feet

More information

Lesson 8: Application Technology

Lesson 8: Application Technology The type of ppliction equipment used must suit the type of ppliction. In this module, you ll lern the prts of the most common types of ppliction equipment used by ssistnt pplictors, s well s how to properly

More information

VB-7253 Series. Application. Features. Applicable Literature

VB-7253 Series. Application. Features. Applicable Literature VB-7253 Series 1/2 to 2 Screwed NPT Stinless Steel Trim with Teflon Disc Stem Up Open, Two-Wy Vlves Generl Instructions Appliction VB-7253 series single set, stem down to close, two wy vlves control wter

More information

Owner s Manual. For TH330MR1 Hydraulic Winches Dedicated for Personnel Lifting

Owner s Manual. For TH330MR1 Hydraulic Winches Dedicated for Personnel Lifting Red this Owner s Mnul thoroughly before operting the equipment. Keep it with the equipment t ll times. Replcements re vilble from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com IMPORTANT:

More information

Owner s Manual For M452 and M492 Series Spur Gear Hand Winches ORIGINAL TEXT

Owner s Manual For M452 and M492 Series Spur Gear Hand Winches ORIGINAL TEXT Red this Owner s Mnul thoroughly efore operting the equipment. Keep it with the equipment t ll times. Replcements re ville from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com IMPORTANT:

More information

Firearm Safety. Links to Topics below XAVIER BECERRA THE SIX BASIC GUN SAFETY RULES. Attorney Genera] The. Six Basic Gun Safety Rules

Firearm Safety. Links to Topics below XAVIER BECERRA THE SIX BASIC GUN SAFETY RULES. Attorney Genera] The. Six Basic Gun Safety Rules firerm Sfety Stte of Cliforni - Deprtment of Justice - Office of the Attorney Generl Pge 1 of 14 Stte of Cliforni Deprtment of]ustice XAVIER BECERRA Attorney Gener] Serch Trnslte Website Trducir Sitio

More information

Bypass Compensator Cartridge, Size 16

Bypass Compensator Cartridge, Size 16 Bypss Compenstor Crtridge, Size 6 Q mx = 5 l/min, p mx = 42 br Direct cting, djustble compenstor spring Description These direct-cting bypss pressure-compenstor (hydrostt) crtridges, series DWDP-2B -6,

More information

The Discussion of this exercise covers the following points: The open-loop Ziegler-Nichols method. The open-loop Ziegler-Nichols method

The Discussion of this exercise covers the following points: The open-loop Ziegler-Nichols method. The open-loop Ziegler-Nichols method Exercise 6-3 Level Process Control EXERCISE OBJECTIVE In this exercise, you will perform PID control of level process. You will use the open-loop step response method to tune the controller. DISCUSSION

More information

Grand Espresso Corner Kitchen

Grand Espresso Corner Kitchen Please retain this information for future reference PRTS LIST To order replacement parts, please visit 1 2 3 4 6 5 7 8 9 10 11 12 13 19 22 16 17 18 20 23 24 25 14 15 21 26 28 30 31 32 33 29 34 36 37 27

More information

Owner s Manual For 5122 Series Portable Davit Cranes ORIGINAL TEXT

Owner s Manual For 5122 Series Portable Davit Cranes ORIGINAL TEXT Red this Owner s Mnul thoroughly efore operting the equipment. Keep it with the equipment t ll times. Replcements re ville from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com IMPORTANT:

More information

400 Series Flat Panel Monitor Arm Rotate Mount Double Pivot P/L

400 Series Flat Panel Monitor Arm Rotate Mount Double Pivot P/L User's Guide 400 Series Flt Pnel Monitor Arm Rotte Mount Doule Pivot P/L < 23ls. (10.44 kg) For the ltest User Instlltion Guide plese visit: www.ergotron.om 1 of 10 Hzrd Symols Review These symols lert

More information

SETUP & PREPARATION KNOW YOUR PRODUCT 1. ASSEMBLY CORDLESS POLE PRUNER. Fitting Rear Handle

SETUP & PREPARATION KNOW YOUR PRODUCT 1. ASSEMBLY CORDLESS POLE PRUNER. Fitting Rear Handle STANDARD EQUIPMENT Pole Chin Guide Br CORDLESS POLE PRUNER Guide Br Cover INSTRUCTION MANUAL Rer Hndle SPECIFICATIONS Input: Br Length: Cutting Length Mx.: Chin Speed: Oil Tnk Cpcity: Length: Weight: 18V

More information

Owner s Manual For 4WM2 Series Worm Gear Hand Winch ORIGINAL TEXT

Owner s Manual For 4WM2 Series Worm Gear Hand Winch ORIGINAL TEXT Red this Owner s Mnul thoroughly efore operting the equipment. Keep it with the equipment t ll times. Replcements re ville from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com IMPORTANT:

More information

Owner s Man ual. For 4HPF/4HWF/4HBP Series Helical/Parallel, Helical/Worm, Helical/Bevel and Planetary Gear Power Winches

Owner s Man ual. For 4HPF/4HWF/4HBP Series Helical/Parallel, Helical/Worm, Helical/Bevel and Planetary Gear Power Winches Red this Own er s Mn u l thor ough ly e fore op er t ing the equip ment. Keep it with the equip ment t ll times. Re plce ments re vil le from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com

More information

Instructions. Electronic Aquarium Water Change System. Replenishing Water. Extracting Water. Includes instructions for:

Instructions. Electronic Aquarium Water Change System. Replenishing Water. Extracting Water. Includes instructions for: Instructions Electronic Aqurium Wter Chnge System Includes instructions for: Replenishing Wter Extrcting Wter INTRODUCTION WHAT S INCLUDED The Aquplenish Wter Chnger conditions, monitors nd replenishes

More information

How To Demonstrate Guide E24 & E26

How To Demonstrate Guide E24 & E26 Pre-Demonstrtion Checklist Clen the entire mchine Chrge tteries Check squeegee ldes Bring proper rushes nd/or pds Clening cost nlysis Prepre quottion with lese pyments E24 & E26 literture nd fct sheet

More information

Owner s Manual For TAC Series Planetary Gear Air Winches ORIGINAL TEXT

Owner s Manual For TAC Series Planetary Gear Air Winches ORIGINAL TEXT Red this Owner s Mnul thoroughly efore operting the equipment. Keep it with the equipment t ll times. Replcements re ville from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com IMPORTANT:

More information

CAUTION - PUT SAFETY FIRST

CAUTION - PUT SAFETY FIRST www.shoremaster.com DVS Vertical Lift (Double V Side): Frame ssembly Instructions. Models: 500DVS - 0ft Wide, 5000lb Capacity - Part #: 0079 600DVS - 0ft Wide, 6000lb Capacity - Part #: 0033.. 3.. 5. CUTION

More information

Pool Ladder. Owner s Manual For: 52in (132 cm) model. For illustrative purposes only. Pool is not provided.

Pool Ladder. Owner s Manual For: 52in (132 cm) model. For illustrative purposes only. Pool is not provided. () 52 2-SECTIONS POOL LDDER ENGLISH 7.5 X 10.3 PNTONE 295U 0/17/201 OWNER S MNUL Pool Ladder Owner s Manual For: 52in (132 cm) model For illustrative purposes only. Pool is not provided. IMPORTNT SFETY

More information

Hot-Air Blowers 12 / / Hot-Air Blowers

Hot-Air Blowers 12 / / Hot-Air Blowers Hot-Air Blowers MISTRAL HOTWIND PREMIUM / HOTWIND SYSTEM MISTRAL Accessories HOTWIND Accessories VULCAN SYSTEM VULCAN SYSTEM Accessories IGNITER BM4/BR4 IGNITER BM4/BR4 Accessories 12 / 13 14 / 15 16 17

More information

* LANDING ROLLED CURB SIDEWALK RAMP TYPE R (ROLLED SIDES) * LANDING ** RAMP FULL CURB HEIGHT MAY BE REDUCED TO ACCOMMODATE MAXIMUM SIDE FLARE SLOPE

* LANDING ROLLED CURB SIDEWALK RAMP TYPE R (ROLLED SIDES) * LANDING ** RAMP FULL CURB HEIGHT MAY BE REDUCED TO ACCOMMODATE MAXIMUM SIDE FLARE SLOPE * MXIMUM LNDING IS 2.0% IN ECH DIRECTION OF TRVEL. LNDING MINIMUM DIMENSIONS 5' x 5'. ** MXIMUM RMP CROSS IS 2.0%, RUNNING 5% - 7% (8.3% MXIMUM). "NON-WLKING" RE * LNDING 24" CROSS FULL WIDTH PERMNENT

More information

Pool Ladder. Owner s Manual For: 36in (91 cm), 42in (107 cm), 48in (122 cm) models. For illustrative purposes only.

Pool Ladder. Owner s Manual For: 36in (91 cm), 42in (107 cm), 48in (122 cm) models. For illustrative purposes only. (), 2, 8 1-SECTION OL LDDER ENGLISH 7. X 10. PNTONE 29U 0/1/2017 English OWNER S MNUL IMRTNT SFETY RULES Read, Understand, and Follow all Instructions Carefully before Installing and using this Product.

More information

United States Patent (19)

United States Patent (19) United Sttes Ptent (19) Mobley (11) 45) Ptent Number: Dte of Ptent: Nov. 19, 1991 (54) BICYCLE RACK FORMOUNTING ON A VAN 76 Inventor: Mrk H. Mobley, P.O. Box 636, Norris, Tenn. 37828 21 Appl. No.: 436,492

More information

Pool Ladder. Owner s Manual For: 48in (122 cm) model. For illustrative purposes only. Pool is not provided. IMPORTANT! DO NOT RETURN PRODUCT TO STORE

Pool Ladder. Owner s Manual For: 48in (122 cm) model. For illustrative purposes only. Pool is not provided. IMPORTANT! DO NOT RETURN PRODUCT TO STORE OWNER S MNUL Pool Ladder Owner s Manual For: 48in (122 cm) model For illustrative purposes only. Pool is not provided. IMPORTNT SFETY RULES Read, understand, and follow all instructions carefully before

More information

Pool Ladder. Owner s Manual For: 52" (132 cm) model. For illustrative purposes only.

Pool Ladder. Owner s Manual For: 52 (132 cm) model. For illustrative purposes only. () 52 2-SECTIONS OL LDDER ENGLISH 7.5 X 10.3 PNTONE 295U 05/20/2017 OWNER S MNUL Pool Ladder Owner s Manual For: 52" (132 cm) model For illustrative purposes only. IMRTNT SFETY RULES Read, understand,

More information

Owner s Man ual. For MTA1000 and MTA2000 Series Cycloidal Gear Air Winches

Owner s Man ual. For MTA1000 and MTA2000 Series Cycloidal Gear Air Winches Red this Own er s Mn u l thor ough ly e fore op er t ing the equip ment. Keep it with the equip ment t ll times. Re plce ments re vil le from Thern, Inc., PO Box 347, Winon, MN 55987, 507-454-2996. www.thern.com

More information

Valve Proving System for automatic Shutoff Valves

Valve Proving System for automatic Shutoff Valves 7 66 VVGYR Vlve Proving System for utomtic Shutoff Vlves 11... The 11 vlve proving system is designed for use with shutoff vlves in connection with gs burners nd gs pplinces. In the event of indmissible

More information

YEARS SKIBOCK CONSTRUCTION MANUAL cm / inch 90kg / 198 lbs 1.5 hours. Length Max weight Time to build

YEARS SKIBOCK CONSTRUCTION MANUAL cm / inch 90kg / 198 lbs 1.5 hours. Length Max weight Time to build SKIOCK CONSTRUCTION MNUL 8 YERS Length Max weight Time to build 130-190 cm / 51-75 inch 90kg / 198 lbs 1.5 hours WRNING - IMPORTNT NOTICE TO PRENTS efore you start constructing and use our product, please

More information

Chapter 4 Group of Volunteers

Chapter 4 Group of Volunteers CHAPTER 4 SAFETY CLEARANCE, FREEBOARD AND DRAUGHT MARKS 4-1 GENERAL 4-1.1 This chpter specifies the minimum freebord for inlnd wterwy vessels. It lso contins requirements concerning the indiction of the

More information

UNIFORM STANDARD DRAWINGS CLARK COUNTY AREA, NEVADA YEAR 2016 REVISIONS

UNIFORM STANDARD DRAWINGS CLARK COUNTY AREA, NEVADA YEAR 2016 REVISIONS , NEVD YER 2016 REVISIONS DWG NO. TITLE ND REVISIONS SUMMRY EFFECTIVE DTE 223.1 Residential Driveway without djacent Sidewalk 7/1/2016 New Drawing to allow flexibility in Roadway Design. 234.1 Typical

More information

THERMOFLO FLUID PUMPS& SYSTEMS THERMOFLO FOR HEATING, COOLING AND WATER SUPPLY APPLICATIONS TO BS7074 SEALED SYSTEMS EXPANSION VESSELS PRESSURIZERS

THERMOFLO FLUID PUMPS& SYSTEMS THERMOFLO FOR HEATING, COOLING AND WATER SUPPLY APPLICATIONS TO BS7074 SEALED SYSTEMS EXPANSION VESSELS PRESSURIZERS THERMOFLO S E A L E D S Y S T E M S THERMOFLO SEALED SYSTEMS FOR HEATING, COOLING AND WATER SUPPLY APPLICATIONS TO BS7074 EXPANSION VESSELS PRESSURIZERS PUMPS& SYSTEMS WALL OR BASE MOUNTING PRESSURIZERS

More information

For ELECTRIC ANCHOR WINCH Models: T Pontoon 35 T sw Salt Water Series Coastal 35

For ELECTRIC ANCHOR WINCH Models: T Pontoon 35 T sw Salt Water Series Coastal 35 INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCHES For ELECTRIC ANCHOR WINCH Models: T10109-35 Pontoon 35 T10102-35sw Salt Water Series Coastal 35 If you have any questions or difficulty installing

More information

TWO BIKE UPRIGHT ROOF MOUNT BIKE CARRIER

TWO BIKE UPRIGHT ROOF MOUNT BIKE CARRIER TWO IKE UPRIGT ROOF OUNT IKE CRRIER NOTE: Please read instructions carefully before installation. Please refer to assembly instructions, and ensure the bike carrier is installed correctly. Please keep

More information

Bicycle wheel and swivel chair

Bicycle wheel and swivel chair Aim: To show conservtion of ngulr momentum. To clrify the vector chrcteristics of ngulr momentum. (In this demonstrtion especilly the direction of ngulr momentum is importnt.) Subjects: Digrm: 1Q40 (Conservtion

More information

his is a preview only - it is not a valid BS7671 certificate. This is a nly - it is not a valid BS7671 certificate. This is a preview only - it is

his is a preview only - it is not a valid BS7671 certificate. This is a nly - it is not a valid BS7671 certificate. This is a preview only - it is certificte vlid the seril review - it vlid number hs been defced certificte. or ltered nly - it vlid ELECTRICAL certificte. INSTALLATION CERTIFICATE - it Issued in ccordnce with Brith Stndrd 7671 Requirements

More information

LK4420BFFR - FTN, 4420BFFR - FTN. Owners Manual

LK4420BFFR - FTN, 4420BFFR - FTN. Owners Manual Owners Manual 4420 Bottle Filler Freeze Resistant Tubular Fountain with 98837C or 98838C Dual Valve Control ssembly MODEL 4420BF1LFR MODEL 4420BF1UFR MODEL 4420BF2FR ITLLER 4420BFFR Fountains are among

More information

ANNEX 1 CLASSIFICATION AND LABELLING SUMMARY TABLES

ANNEX 1 CLASSIFICATION AND LABELLING SUMMARY TABLES ANNEX CLASSIFICATION AND LABELLING SUMMARY TABLES ANNEX CLASSIFICATION AND LABELLING SUMMARY TABLES NOTE: The codifiction of hzrd s is further explined in Annex 3 (Section ). The hzrd re intended to be

More information

For ANCHOR WINCH Model: T Big Water 45 T sw Salt Water Series Big Water 45

For ANCHOR WINCH Model: T Big Water 45 T sw Salt Water Series Big Water 45 INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCHES For ANCHOR WINCH Model: T10110-45 Big Water 45 T10103-45sw Salt Water Series Big Water 45 If you have any questions or difficulty installing this

More information

GRENADES INTRODUCTION: EOD CONSIDERATIONS ANTI-ARMOR/HEAT: SAFETY: FRAGMENTATION: IMPACT FRAGMENTATION: FOR OFFICIAL USE ONLY FOR OFFICIAL USE ONLY

GRENADES INTRODUCTION: EOD CONSIDERATIONS ANTI-ARMOR/HEAT: SAFETY: FRAGMENTATION: IMPACT FRAGMENTATION: FOR OFFICIAL USE ONLY FOR OFFICIAL USE ONLY INTRODUCTION: Hnd or rifle projected. Min chrge includes HE, riot-control gents, smokes, nd incendiry nd pyrotechnic mterils. Fuzing is vried nd my be time-dely or impct fuzed. Are esily nd frequently

More information

OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 3K Puller (M3K-M)

OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 3K Puller (M3K-M) OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 3K Puller (M3K-M) 04/17 (M3K-M) READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND SAFETY INFORMATION IN THIS MANUAL BEFORE OPERATING OR SERVICING THIS TOOL TABLE

More information

SGP-20S SGP-25S SGP-32S SGP-40S. Price $ $ $ $ Filtered compressed air, lubricated or non-lubricated

SGP-20S SGP-25S SGP-32S SGP-40S. Price $ $ $ $ Filtered compressed air, lubricated or non-lubricated SGP-S -JW SELF-ENTERING PRLLEL PNEUMTI GRIPPER (SERIES SGP-S) Double-ting. Ptented bklsh djusting system. High performne in ompt size. The rugged onstrution ensures trouble-free long life nd relibility

More information

2014 Victorian Shooting Championship

2014 Victorian Shooting Championship 2014 Victorin Shooting Chmpionship VPCI, in conjunction with the Stte Coches nd the Stte Umpires invite ll PFA licensed petnque plyers in the Stte of Victori to tke prt in the 2014 Victorin Shooting Chmpionship.

More information

INSTALLATION AND OPERATING INSTRUCTIONS. T10219-AD Deckboat 40 with AutoDeploy and Wireless Remote Control

INSTALLATION AND OPERATING INSTRUCTIONS. T10219-AD Deckboat 40 with AutoDeploy and Wireless Remote Control INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCH T10219-AD Deckboat 40 with AutoDeploy and Wireless Remote Control If you have any questions or difficulty installing this product, we are here to help!

More information

OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M)

OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M) OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M) READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND SAFETY INFORMATION IN THIS MANUAL BEFORE OPERATING OR 04/17 (M6K-M) SERVICING THIS TOOL TABLE

More information

ERRATA for Guide for the Development of Bicycle Facilities, 4th Edition (GBF-4)

ERRATA for Guide for the Development of Bicycle Facilities, 4th Edition (GBF-4) Dvid Bernhrdt, P.E., President Commissioner, Mine Deprtment of Trnsporttion Bud Wright, Executive Director 444 North Cpitol Street NW, Suite 249, Wshington, DC 20001 (202) 624-5800 Fx: (202) 624-5806 www.trnsporttion.org

More information

Thank You. Warranty Message

Thank You. Warranty Message Thnk You Thnk you for purhsing MotorGuide Xi5 Wireless Trolling Motor. The Xi5 is designed nd engineered to deliver the performne tht nglers expet: quiet opertion, reliility, nd preise ontrol. We re onfident

More information

Inflatable Acoustical Shell

Inflatable Acoustical Shell Owner s Manual Inflatable coustical Shell CONTENTS Safety Precautions.............................2 Set Up and Usage.........................2 Stability..................................3 Fire Hazard...............................3

More information

HITCH MOUNT TWO-ARM BIKE CARRIER

HITCH MOUNT TWO-ARM BIKE CARRIER TC MOUNT TWO-RM BKE CRRER NOTE: Please read instructions carefully before installation. Please refer to assembly instructions, and ensure the bike carrier is installed correctly. Please keep the instruction

More information

Dual Monitor Desk Mount

Dual Monitor Desk Mount Dul Mnitr Desk Munt Instructin Mnul SKU: STAND-V002 Scn the QR cde with yur mbile device r llw the link r helpul vides nd speciictins relted t this prduct. https://viv-us.cm/prducts/stnd-v002 help@viv-us.cm

More information

First Aid in School Policy

First Aid in School Policy First Aid in School Policy Approved y the Governing Body of West Monkton Church of Englnd Primry School: Reviewed y Governors nd Agreed: Septemer 2017 At West Monkton we im to e n inspirtionl community,

More information

Inflatable Stand Up Paddle Board Manual

Inflatable Stand Up Paddle Board Manual Inflatable Stand Up Paddle Board Manual V-Max AIR 12 6 Voyager AIR 11 6 Koa AIR 10 2 and 10 8 Heavy duty built in carrying handles Steel D Ring Built in Cargo Straps EVA Deck Pad High Pressure Air Valve

More information

OWNERS MANUAL. Model Shown with optional Primary Mooring Cleats. Portable Mooring System SAFETY OPERATION MAINTENANCE PARTS

OWNERS MANUAL. Model Shown with optional Primary Mooring Cleats. Portable Mooring System SAFETY OPERATION MAINTENANCE PARTS OWNERS MANUAL Model 2400 Shown with optional Primary Mooring Cleats. Portable Mooring System SAFETY OPERATION MAINTENANCE PARTS CAUTION: Before using your new Pier Tender, read rules for Safety, Operation,

More information

POWER COMBICON feed-through plugs mm pitch DFK-PC 16/...-ST(F)-10,16

POWER COMBICON feed-through plugs mm pitch DFK-PC 16/...-ST(F)-10,16 feed-through plugs 0.6 mm pitch DFK-PC 6/...-ST(F)-0,6 If 6 mm conductor is used, the new feed-through plug connector offers the possibility to trnsfer current of 76 A from inside the device to outside

More information

DM-SL (English) Dealer's Manual. REVOSHIFT Shifter SL-RS47 SL-RS45 SL-RS36 SL-RS35 SL-RS34 SL-RS25

DM-SL (English) Dealer's Manual. REVOSHIFT Shifter SL-RS47 SL-RS45 SL-RS36 SL-RS35 SL-RS34 SL-RS25 (English) DM-SL0002-03 Dealer's Manual REVOSHIFT Shifter SL-RS47 SL-RS45 SL-RS36 SL-RS35 SL-RS34 SL-RS25 IMPORTNT NOTICE This dealer's manual is intended primarily for use by professional bicycle mechanics.

More information

Instruction Manual. The Blackhawk XC. Model FP015

Instruction Manual. The Blackhawk XC. Model FP015 Instruction Manual The Blackhawk XC Model FP015 TTENTION!! WHEN YOU SEE WRNING! BE SURE TO HEED THE MESSGE! THE INFORMTION CONTINED IN THESE MESSGES CN SVE YOUR LIFE!! PLESE NOTE THT WRNING! statements

More information

Valve Proving System for automatic Shutoff Valves

Valve Proving System for automatic Shutoff Valves LGY lve Proving System for utomtic Shutoff lves 11... The 11... vlve proving system is designed for use with shutoff vlves in connection with gs urners nd gs pplinces. n the event of indmissile lekge,

More information

Reel Away (cord reeler)

Reel Away (cord reeler) Reel way (For ftermarket pplications) Reel way Installation and Owner s Manual (For ftermarket pplications) Features The Standard Reel way stores cords up to 36 feet in length. The Deluxe Reel way stores

More information

CAL. YM91 CHRONOGRAPH

CAL. YM91 CHRONOGRAPH CL. YM91 CHRONOGRPH TIME/CLENDR Hour, minute and small second hands Date displayed in numerals Measures up to 60 minutes in 1/5 second increments. Split time measurement ENGLISH DISPLY ND CROWN/UTTONS

More information

T POOL ASSEMBLY AND INSTALLATION MANUAL. Trinidad LX Above Ground 52 Round Extruded Wall Pools

T POOL ASSEMBLY AND INSTALLATION MANUAL. Trinidad LX Above Ground 52 Round Extruded Wall Pools T3668-80 POOL SSEMLY ND INSTLLTION MNUL Trinidad LX bove Ground 52 Round Extruded Wall Pools Note: Deck and fence accessories shown are optional. THIS MNUL EXPLINS THE CORRECT METHOD TO SSEMLE YOUR NEW

More information

ARIAKON OWNER S MANUAL READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS PAINTBALL MARKER.

ARIAKON OWNER S MANUAL READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS PAINTBALL MARKER. RIKON Thank You for choosing RIKON SIM-5 SERIES.68 CLIER PINTLL MRKER (SIM-5. SIM-5 PRO, SIM-5 PRO ELITE) RIKON 2794 LOKER VE WEST SUITE 107 CRLSD C 92010 1-877-4-RIKON 760-268-0735 FX 760-268-0736 On

More information

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS 18 GAUGE 1-1/4 INCH BRAD NAILER Model: 7611 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.

More information

VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns , , , , , )

VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns , , , , , ) VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns 3714022, 3714028, 3714034, 3714040, 3714043, 3714046) REIMANN & GEORGER CORPORATION MARINE PRODUCTS BUFFALO, NY P/N 6112103 04/09/18 1 SAFETY 1.1 INTRODUCTION

More information

APPNA SPRING MEETING CHICAGO, ILLINOIS RETAIL BAZAAR REGISTRATION MARRIOTT DOWNTOWN MAGNIFICENT MILE 540 NORTH MICHIGAN AVENUE

APPNA SPRING MEETING CHICAGO, ILLINOIS RETAIL BAZAAR REGISTRATION MARRIOTT DOWNTOWN MAGNIFICENT MILE 540 NORTH MICHIGAN AVENUE 1 PPN SPRING MEETING 2018 CHICGO, ILLINOIS PRIL 26 29, 2018 MRRIOTT DOWNTOWN MGNIFICENT MILE 540 NORTH MICHIGN VENUE RETIL ZR REGISTRTION 2 COMPNY NME CONTCT NME DDRESS RETIL ZR REGISTRTION PREFERRED PHONE

More information

GETZ EQUIPMENT INNOVATORS PART NO.: 9G59554 MODEL: MS 36 SC-R HYDROSTATIC TEST PUMP

GETZ EQUIPMENT INNOVATORS PART NO.: 9G59554 MODEL: MS 36 SC-R HYDROSTATIC TEST PUMP GETZ EQUIPMENT INNOVATORS PART NO.: 9G59554 MODEL: MS 36 SC-R HYDROSTATIC TEST PUMP LIMITED WARRANTY Getz Equipment Innovators warrants its products, and component parts of any product manufactured by

More information

R E D I C O N T R O L S

R E D I C O N T R O L S R E D I C O N T R O L S Operation & Maintenance Manual Portable Service Purger for Low Pressure Chillers Model: PSP-LP-1B For Refrigerants R-11, R-113, R-114 & R-123 & Other Similar Refrigerants File Literature

More information

600 / 600FC OWNER'S MANUAL

600 / 600FC OWNER'S MANUAL PROGRESSION 600 / 600FC OWNER'S MANUAL Issue 2 / Version E - Dec. 10, 1997 Copyright 1997 GAMMA Sports - All Rights Reserved PROGRESSION 600 / 600FC OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY

More information

2,500/4,000 LB Easy Riser Vertical Cable Feighner Lift

2,500/4,000 LB Easy Riser Vertical Cable Feighner Lift 2,500/4,000 LB Easy Riser Vertical Cable Feighner Lift CAUTION - PUT SAFETY FIRST 1. Before attempting to install or operate this lift, study and fully understand the proper operating procedures and safety

More information

CATERPILLAR XL G2 YEARS CONSTRUCTION MANUAL

CATERPILLAR XL G2 YEARS CONSTRUCTION MANUAL 6-14 CTERPILLR XL G2 YERS CONSTRUCTION MNUL Length Max weight Time to build 120-168 cm / 47-66 inch 70 kg / 153 lbs 2 hours WRNING - IMPORTNT NOTICE TO PRENTS efore you start constructing and use our product,

More information

Pressure Dump Valve Service Kit for Series 2300 Units

Pressure Dump Valve Service Kit for Series 2300 Units Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit

More information

bark bark bat bat Multiple Meaning Words: Kindergarten to Grade 2 More Teaching Tools at harsh sound made by a dog

bark bark bat bat Multiple Meaning Words: Kindergarten to Grade 2 More Teaching Tools at  harsh sound made by a dog the brk the brk bt bt hrsh sound mde by dog Mx, stop brking! outside cover of the trunks, brnches, nd roots of woody plnts The brk of this tree is very rough. club of wood or metl used to hit the bll in

More information

MALONER. Installation & Loading Instructions - Please Read Before Beginning. Step 1: Installing Carriers to Cross Bars

MALONER. Installation & Loading Instructions - Please Read Before Beginning. Step 1: Installing Carriers to Cross Bars SeaWing V-STYLE KAYAK CARRIER 60mm 50mm Rubber Plugs SeaWing Kayak Carriers 12 Load Straps Jawz Universal Adapters Mounting Bolts T-Knobs 12 Safety Lines MD Series Only Installation & Loading Instructions

More information

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS 18 GAUGE 2 INCH BRAD NAILER Model: 7555 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.

More information

DO NOT use any Alien Flier Zip Line Products or Accessories until you read and understand these SAFETY WARNINGS!

DO NOT use any Alien Flier Zip Line Products or Accessories until you read and understand these SAFETY WARNINGS! ! WARNING DO NOT use any Alien Flier Zip Line Products or Accessories until you read and understand these SAFETY WARNINGS! A zip line can be very dangerous. Do not use this kit if you do not understand

More information

T-016 ASSEMBLY MANUAL MODEL ROCK AND ROLL Main Street NE Minneapolis, MN

T-016 ASSEMBLY MANUAL MODEL ROCK AND ROLL Main Street NE Minneapolis, MN MODEL T-016 ASSEMBLY MANUAL ROCK AND ROLL 5280 Main Street NE Minneapolis, MN 55421 1.877.226.7824 www.kurtkinetic.com COMPONENTS Tools Required for Assembly: 17mm Wrench or Adjustable Wrench When unpacking,

More information

VOLUME III SKI-DOO SNOWMOBILE FLAT RATE TIME SCHEDULE FORMULA* III / III LT MACH* I MACH* Z / Z LT GRAND TOURING* SE. Bombardier Inc.

VOLUME III SKI-DOO SNOWMOBILE FLAT RATE TIME SCHEDULE FORMULA* III / III LT MACH* I MACH* Z / Z LT GRAND TOURING* SE. Bombardier Inc. FLT RTE TIME SCHEDULE SKI-DOO SNOWMOBILE 1997 VOLUME III FORMUL* III / III LT MCH* I MCH* Z / Z LT GRND TOURING* SE Effective November 25th, 1996 Subject to review from time to time, without notice or

More information

FREESTANDING WOOD FIRES

FREESTANDING WOOD FIRES FREESTNDING WOOD FIRES F12000HW - USTRLI 2013 Item No. MRKET FUEL TYPE FINISH YER FN 995957 Charcoal VHT Paint U HRDWOOD SEP-2013 Yes 995958 Matt Black Enamel IPL No. : 999173 Issue: Date: Page: 1 of 11

More information

Wildcat LB Winch Kit. Operator s Manual Installation Instructions Replacement Parts List. With Wireless Control System.

Wildcat LB Winch Kit. Operator s Manual Installation Instructions Replacement Parts List. With Wireless Control System. p/n 2259-560 Wildcat 4000 LB Winch Kit With Wireless Control System Operator s Manual Installation Instructions Replacement Parts List 2012 Arctic Cat Inc. Trademarks of Arctic Cat Inc. Thief River Falls,

More information

Cocoa Patio Pond with Lit Spillway

Cocoa Patio Pond with Lit Spillway Cocoa Patio Pond with Lit Spillway REMINDER CALL 1-888-755-5641 BEFORE RETURNING TO STORE. PACKAGE CONTENTS ITEM # GQSPPB/GQSPPW Questions, problems, missing parts? Before returning to your retailer, call

More information

Vertical Lift: Frame Assembly Instructions. Model: ft Wide 7000lb Capacity - Part #:

Vertical Lift: Frame Assembly Instructions. Model: ft Wide 7000lb Capacity - Part #: www.shoremaster.com 70068 Vertical Lift: Frame ssembly Instructions. Model: 70068-0ft Wide 7000lb apacity - Part #: 0070. 2. 3.. 5. UTION - PUT SFETY FIRST Before attempting to install or operate this

More information

SNOWDRIFTER G1 CONSTRUCTION MANUAL

SNOWDRIFTER G1 CONSTRUCTION MANUAL ch 7-14 SNOWDRIFTER G1 CONSTRUCTION MNUL YERS Length Max weight Time to build 98-125 cm / 39-49 inch 80kg / 176 lbs 2 hours WRNING - IMPORTNT NOTICE TO PRENTS efore you start constructing and use our product,

More information

Pressure Dump Valve Service Kit for Series 3000 Units

Pressure Dump Valve Service Kit for Series 3000 Units Instruction Sheet Pressure Dump Valve Service Kit for Series 000 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00, 400, 500, and 700 applicator

More information

Owners Manual Bottle Filler Freeze Resistant Tubular Fountain & Pet Fountain with 98837C Dual Valve Control Assembly

Owners Manual Bottle Filler Freeze Resistant Tubular Fountain & Pet Fountain with 98837C Dual Valve Control Assembly LK Owners Manual 4420 Bottle Filler Freeze Resistant Tubular Fountain & Pet Fountain with 98837C Dual Valve Control ssembly MODEL 4420BF1UDBFR MODEL 4420BF1LDBFR ITLLER 4420DBBFFR Fountains are among the

More information

HITCH MOUNT PLATFORM BIKE CARRIER

HITCH MOUNT PLATFORM BIKE CARRIER model no. 040-90-4 HITCH MOUNT PLTFORM BIK CRRIR NOT: Please read instructions carefully before installation. Please refer to assembly instructions and ensure the bike carrier is installed correctly. Please

More information

200 A, 15 and 25 kv class loadbreak bushing insert installation instructions

200 A, 15 and 25 kv class loadbreak bushing insert installation instructions Loadbreak Apparatus Connectors Effective October 2013 Supersedes March 2011 200 A, 15 and 25 kv class loadbreak bushing insert installation instructions S500-12-1 DISCLAIMER OF WARRANTIES AND LIMITATION

More information

(12) Patent Application Publication (10) Pub. No.: US 2003/ A1

(12) Patent Application Publication (10) Pub. No.: US 2003/ A1 US 2003O183916A1 (19) United Sttes (12) Ptent Appliction Publiction (10) Pub. No.: US 2003/0183916A1 Heck et l. (43) Pub. Dte: Oct. 2, 2003 (54) PACKAGING (22) Filed: Mr. 27, 2002 MICROELECTROMECHANICAL

More information

3/8" Dr. Air Butterfly Impact Wrench

3/8 Dr. Air Butterfly Impact Wrench 8192106 3/8" Dr. Air Butterfly Impact Wrench Owner s Manual Read and understand all instructions before use. Retain this manual for future reference. Specifications Construction: Polished aluminum and

More information

OWNER'S MANUAL FISHING AND PONTOON BOAT ANCHOR WINCH. 24' Class Rope Anchor Winch

OWNER'S MANUAL FISHING AND PONTOON BOAT ANCHOR WINCH. 24' Class Rope Anchor Winch OWNER'S MANUAL 24' Class Rope Anchor Winch FISHING AND PONTOON BOAT ANCHOR WINCH PW24101 The 24 Class anchor winch is a 12VDC power winch that retrieves and deploys river, mushroom, or navy type anchors

More information

Installation, Operation & Maintenance Manual

Installation, Operation & Maintenance Manual Original Instructions Installation, Operation & Maintenance Manual Sentry VREL Control Valve Pressure Conditioning S-SW-IOM-00277-15 1-17 Table of Contents Safety Information... 3 General Safety Precautions...

More information

User Instruction Manual

User Instruction Manual User Instruction Manual 4500 psi Air Compressor Ver 2, 1.18 Contents Parts Included...3 Assembly Instructions...3-5 Operation Instructions...6-7 Oil Change Intervals...8 Air Filter Replacement...9 Setting

More information

VL SHEAVES/CABLE UPGRADE KIT INSTRUCTIONS

VL SHEAVES/CABLE UPGRADE KIT INSTRUCTIONS VL SHEAVES/CABLE UPGRADE KIT INSTRUCTIONS RGC MARINE PRODUCTS BUFFALO, NY P/N 6112062 02/03/17 TABLE OF CONTENTS CHAPTER TITLE PAGE 1 SAFETY... 1 1.1 Introduction... 1 1.2 Safety Definitions... 1 1.3 Equipment

More information

OWNER'S MANUAL FREE FALL ROPE AND CHAIN ANCHOR WINCH. 12 Volt Powered Winch Power-In / Freewheel-out operation. 36', 41' and 46' Class Anchor Winch

OWNER'S MANUAL FREE FALL ROPE AND CHAIN ANCHOR WINCH. 12 Volt Powered Winch Power-In / Freewheel-out operation. 36', 41' and 46' Class Anchor Winch OWNER'S MANUAL 36', 41' and 46' Class Anchor Winch FREE FALL ROPE AND CHAIN ANCHOR WINCH PW46101 12 Volt Powered Winch Power-In / Freewheel-out operation These instructions apply to all models listed.

More information

COOPER POWER SERIES. D-73P3 bypass switches installation instructions. Switches MN008005EN. Effective April 2016 Supersedes S June 2013

COOPER POWER SERIES. D-73P3 bypass switches installation instructions. Switches MN008005EN. Effective April 2016 Supersedes S June 2013 Switches MN008005EN Effective April 2016 Supersedes S328-120-1 June 2013 D-73P3 bypass switches installation instructions COOPER POWER SERIES DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY The information,

More information