EVALUATION SUBJECT: CAST IRON SOIL PIPE AND FITTINGS DIVISION: PLUMBING SECTION: SANITARY WASTE AND VENT PIPING.

Transcription

1 ICC-ES Report PMG-1407 Reissued 10/2017 This report is subject to renewal 10/2018 EVALUATION SUBJECT: CAST IRON SOIL PIPE AND FITTINGS DIVISION: PLUMBING SECTION: SANITARY WASTE AND VENT PIPING Report Holder: JC CAST IRON CORP PO BOX 3044 SOUTH EL MONTE, CA 91733

2 ICC-ES PMG Product Certificate PMG-1407 Effective Date: October 2017 This listing is subject to re-examination in one year. (800) (562) A Subsidiary of the International Code Council CSI: DIVISION: PLUMBING Section: Sanitary Waste and Vent Piping Product certification system: The ICC-ES product certification system includes testing samples taken from the market or supplier s stock, or a combination of both, to verify compliance with applicable codes and standards. The system also involves factory inspections, and assessment and surveillance of the supplier s quality system. Product: Listee: Cast Iron Soil Pipe and Fittings JC Cast Iron Corp PO Box 3044 South El Monte, California Compliance with the following codes: 2018, 2015, 2012 and 2009 International Plumbing Code (IPC) 2018, 2015, 2012 and 2009 International Residential Code (IRC) 2015, 2012 and 2009 Uniform Plumbing Code (UPC)* *Copyrighted publication of the International Association of Plumbing and Mechanical Officials Compliance with the following standards: Identification: CISPI , (excluding Annex A) Standard Specification for Hubless Cast Iron Soil Pipe and Fittings For Sanitary and Storm Drain, Waste, and Vent Piping Applications ASTM A , (excluding Annex A1) Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications Each length of pipe and each fitting shall be plainly marked with the country of origin, the manufacturer s name or the manufacturer s registered trademark by which the manufacturer can be readily identified after installation and any appropriate collective mark (optional). The marking shall be adequate identification of the manufacturer of the pipe and fittings if it readily identifies the manufacturer to the end user of the product. Markings shall be cast on fittings. Pipe markings: The pipe shall be marked continuously on the barrel with a minimum of 0.75 inch (19mm) lettering starting within 3 inches of each end of the pipe. Each pipe shall be marked with the date of manufacture and the ICC-ES PMG listing mark. The marking shall be stenciled on the pipe or otherwise applied so as to be clear and legible. Fitting markings: The marking shall be cast with raised letters that are not to be located within the Listings are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the listing or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this listing, or as to any product covered by the listing. Copyright 2017 ICC Evaluation Service, LLC. All rights reserved. Page 1 of 4

3 PMG-1407 Most Widely Accepted and Trusted Page 2 of 4 Installation: Models: W dimension. Cast markings shall be raised from the wall of the fitting unless otherwise noted. Fittings or fittings packaging shall be marked with ICC-ES PMG listing mark. The JC Cast Iron Corp pipe and fittings are to be installed in accordance with the manufacturer's instructions and the applicable code JC Cast Iron Corp. pipe and fittings are used in Sanitary Waste Systems and Storm Drain Systems in accordance with the applicable code. PIPE: Hubless Cast Iron Pipe in 5 and 10 Feet Nominal Lengths 0156 Pipe 1-1/2" 0158 Pipe Pipe Pipe Pipe Pipe Pipe 10 FITTINGS: 0188 ¼ Bend 1-1/2" 0190 ¼ Bend ¼ Bend ¼ Bend ¼ Bend ¼ Bend Low Heel ¼ Bend 3" x 2" 0282 Low Heel ¼ Bend 4" x Short Sweep ¼ Bend Short Sweep ¼ Bend Short Sweep ¼ Bend Short Sweep Short Sweep ¼ Bend Long Sweep ¼ Bend 1-1/2" 0494 Long Sweep ¼ Bend Long Sweep ¼ Bend Long Sweep ¼ Bend /5 Bend /5 Bend /5 Bend /6 Bend /6 Bend /6 Bend /8 Bend 1-1/2" /8 Bend /8 Bend /8 Bend /8 Bend /8 Bend 8

4 PMG-1407 Most Widely Accepted and Trusted Page 3 of /16 Bend 1-1/2" /16 Bend /16 Bend /16 Bend /16 Bend 6" /16 Bend Sanitary Tee 1-1/2" 0808 Sanitary Tee 2 x 1-1/2" 0810 Sanitary Tee Sanitary Tee 3 x Sanitary Tee Sanitary Tee 4 x Sanitary Tee 4 x Sanitary Tee Sanitary Tee 6 x 4" 0836 Sanitary Tee Sanitary Tapped Tee 1-1/2" 1214 Sanitary Tapped Tee 2 x 1-1/2" 1216 Sanitary Tapped Tee 2 x Sanitary Tapped Tee 3 x 1-1/2" 1222 Sanitary Tapped Tee 3 x Sanitary Tapped Tee 4 x 1-1/2" 1228 Sanitary Tapped Tee 4 x Wye 1-1/2" 1314 Wye Wye 3 x Wye Wye 4 x Wye 4 x 3" 1324 Wye Wye 6 x Wye Wye 8 x Wye 8 x Double Wye Double Wye 3 x Double Wye Double Wye 4 x Double Wye 4 x Wye Branch Upright Wye Branch Upright 3 x Wye Branch Upright Combination Wye 1/8 Bend 1-1/2" 1696 Combination Wye 1/8 Bend 2 x 1-1/2" 1698 Combination Wye 1/8 Bend Combination Wye 1/8 Bend 3 x Combination Wye 1/8 Bend Combination Wye 1/8 Bend 4 x Combination Wye 1/8 Bend 4 x 3" 1708 Combination Wye 1/8 Bend Combination Wye 1/8 Bend 6 x Combination Wye 1/8 Bend Combination Wye 1/8 Bend 8 x Combination Wye 1/8 Bend 8 x Combination Wye 1/8 Bend Sanitary Cross Tee 3 x Sanitary Cross Tee 3

5 PMG-1407 Most Widely Accepted and Trusted Page 4 of Sanitary Cross Tee 4 x Sanitary Cross Test Tee Test Tee Test Tee Increaser/Reducer 2 x 1-1/2" 2140 Increaser/Reducer 3 x Increaser/Reducer 4 x Increaser/Reducer 4 x Increaser/Reducer 6 x Increaser/Reducer 6 x Tapped Adapter 2 x 1-1/2" 2244 Tapped Adapter 2 x Tapped Adapter 3 x Blind Plug Blind Plug Blind Plug Blind Plug P-Trap 1-1/2" 2508 P-Trap P-Trap P-Trap P-Trap w/ Tapped Inlet 2 x 1-1/2" 2832 Closet Bend 3 x 4 x 6 x Closet Bend 3 x 4 x 6 x Closet Bend 4 x 4 x 6 x Closet Bend 4 x 4 x 6 x Closet Bend 4 x 4 x 6 x Closet Flange 4 x Closet Flange 4 x Closet Flange 4 x Figure 1A Fitting 2 x 2 x 1-1/2" x 1-1/2" 8052 Figure 5 Fitting Figure 5 Fitting 3 x Figure 5 Fitting Figure 5 Fitting 4 x Figure 5 Fitting Figure 5 Extended Fitting 3 x Two-Way Cleanout 3 x 3 x Two-Way Cleanout 4 x 4 x P-Trap w/ ½ Tap Primer P-Trap w/ ½ Tap Primer Iron Body Cleanout, Tapped Iron Body Cleanout, Tapped 4 Conditions of Listing: 1. JC Cast Iron Corp pipe and fittings must be installed in accordance with this listing, the applicable code and the manufacturer s published installation instructions. The instructions within this listing must govern if there are any conflicts between the manufacturer s published instructions and this listing. 2. The models recognized in this listing are distributed JC Cast Iron Corp in El Monte, California under a quality control program with annual surveillance inspections by ICC-ES.