Here's the comparison of the stock rock shaft vs. a 3pt rock shaft.

Size: px
Start display at page:

Download "Here's the comparison of the stock rock shaft vs. a 3pt rock shaft."

Transcription

1 This documents a build of a Category 0 3 point hitch for the John Deere 316 Onan, 318, 322, 330, 332, 420 and 430 tractors. This is Neil Koch's build for his 318. Here's the comparison of the stock rock shaft vs. a 3pt rock shaft. Here is the steel to make the upper lift arms. Use a 1" hole saw for the big holes. The steel for the upper lift arms is 3/8" x 2" The longer ones are 8" long, hole is 1" from end The short ones at bottom are 5 3/8" long.

2 The two above are for center link - 3/16"x2"x5" The large hole are for positioning on "round" part Cut through the center of hole, and will weld back together when positioned on rockshaft. The upper lift arms will look like this when finished. To make each one you will need the following: 1 piece 3/8" x 2" x 8" 1 piece 3/8" x 2" x 5 3/8" 1 piece 3/8" x 2" x 2 1/4" 1 piece 3/8" x 2" x 2 3/4"

3 Here is the upper lift arms finished, you can see the rounded hole at the end to fit on rockshaft. Here is a pic of the fabricated lift arms in comparison to the original 3pt rockshaft.

4 In the pictures above you can see the two pieces of steel for the center link. The holes drilled in the ends needs to be 5/8". Make sure to drill all holes before welding any parts to the rockshaft because it is much easier to get them in a drill press!! You still need to drill the holes through the upper lift arms as well. The tricky part is getting the lift arms mounted at the proper angle in comparison to the deck lift arms. Here is the stock 3pt angle: Notice how the rockshaft is positioned. This is what needs to be done with the non-3pt rockshaft:

5 Finally, here are some measurements for where these pieces go on the rockshaft: The tricky part use a 3/8" piece of steel to hold it up "just right".

6 The center link will be positioned "level" with the surface you are working on, like this: Here is a good way to check that tricky angle for the lift arms I was talking about earlier. Look carefully at the position of the small square in this photo of the stock 3pt rockshaft. Align the flat edge of the deck lift arm with the center of the hole on lift arm. Picture says it better:

7 So, using that as a guide, this is how I will position my lift arm on the rockshaft: Next step is to drill the 5/8" holes in the lift arms to mount the "upper swivels". The biggest concern is

8 the difference in the design of that part the cylinder pushes and pulls on. Notice that the 3-pt rockshaft has a straight slot, and the stock rockshaft has a curved one. How this will effect do the lifting range of the hitch is not know at this time. If mobility needs to be increased, then this area may need to be modified. Here are the upper lift arms and the two pieces of steel for the center link. Here is the rockshaft cleaned up to allow for a better weld.

9 Top view of the lift arm in place. Notice the use of the triangular magnets to help position things. Combined with a steel table, they help when two hands are needed. See how the orange one keeps the arm square with the shaft. The socket it there to space things...it sticks to the magnet. Everything tacked into place. Use the measurements above to find the placement of the lift arms. The one is easy because it goes in between the two pieces that the cylinder pushes on.

10 Welding the center link on after the arms have been tacked into place. Tack weld everything until everything is located. Remember, measure twice, weld once...or something like that! Here's another angle:

11 Here is a shot of fabricated versus factory 3 point rockshaft.. Notice how it is sitting on the table, and how the center link is positioned... level with the table.

12 Here is the almost final product, tacked together and ready to try out: Bolt to tractor to checked for clearances. Up

13 and "down" Next step is to pull it back off, weld all joints really well, and weld the "halves" back on that were a result of cutting through the big 1" holes. This should strengthen things. Also put the category 0 "swivels" in place in the upper lift arms. This will be tricky in an effort to get a good weld with good penetration. For every flat joint that is welded together, cut "V" out the joint in order to provide for more weld and better penetration. Johnny Products provides the Cat 0 stuff you will need for later in the project. These CAT 0 swivels came from a local Kubota dealer for $6 each.

14 Next weld all of the "half sections" back on that was cut originally so that the lift arms would fit on the shaft. Next the upper swivels. Here you can see the original one next to the fabricated one. You will need a CAT 0 swivel joint, and a 5/8" rod to connect it. The longer piece of 5/8" rod is 1 1/8" long. The short one is: 5/8" long. Those are 5/8" steel bushings (like washers) sitting between the rods and swivel.

15 Here is a close up shot of the original that needs to be duplicated: Weld the bushing or washer onto the end of each piece of rod. Welding the bushing on the end and then grinding it smooth will allow more surface area to weld the swivel joint to. This will also prevent it from accidentally welding the swivel to the inside of the lift arm itself. Here is one 1 1/8" long rod with the bushing welded on top. With the bushing welded on, you can put the rod into the pivot hole. One hole will get the 1 1/8" rod,

16 the other side is 5/8" length rod. Here are both short lengths of rod with bushings in place, in their proper pivot holes. The cat 0 swivel is positioned in between, ready to be welded into place. The 1 1/8" long rod sticks out almost 1/2" on the "outside" of the lift arm. This piece sticking out has a small hole in it. Weld those swivels in place and the rockshaft will be done.

17 Rockshaft completed and painted. Here's a shot of the swivel welded into place. Ground down some of the square corners and cleaned it up a bit.

18 Primed and some black paint!!

19 Here's a close up of that swivel all painted up. Next the lower lift arms. Each lift arm is 1/2"x2"x20" flat stock..

20 Thickness is 1/2" steel. The end with the chain bolts to the tractor. In the picture above, the piece in the center is unbent and uncut. From the right end, and at 6 5/8" made a mark, then another mark at 17 3/4". This is where the bends are. Then cut out a "round" piece on the end with a torch to accommodate for the round swivel to be welded in place. Here's another shot.

21 Both bends are actually the same angle, so in essence it will complete a 3 1/4" offset. The angle is 165 degrees or 15 degrees depending upon how you measure (as illustrated above, but I wrote "65" instead of "165"). To do this, bend a thinner piece of steel to the desired angle to use as a guide. Then clamp each lift arm in a vice, heated at the bend line with a torch, and then bend it over with a sledge hammer until the bend matched the guide piece. If you start with two pieces of steel both 20" long, measure and bend them the same, you can produce two very similar pieces Shown below is extra arms for more hitches. Weld the swivel onto the end. Shim the lift arm up off the table in order to center it on the swivel.

22 Just about ready to weld it on...no turning back now!! Here it is welded into place. These swivels allow for a good weld with good penetration.

23 Here are a couple of shots of the lift arms with the swivels welded on the end.

24 The match set!! Drill some holes in the lower lift arms to attach the lifting links, and weld on a small piece to attach the limiting chains. For the swivels - The package says that the producer is "TISCO". The main part number appears to be "B2226". This is what the package reads line for line (refer to the archive pic) (TISCO) Qty. 2 (p/n?) B E Ball Joint Weld on Cat 0 5/8" Bore First thing was to drill the 1/2" hole in the lift arms. The hole appears to be 9" from the bend.

25 Time to build these lower attachment brackets. Some measurements.

26 Here is the smaller piece measured out. The holes are all 5/8" on these brackets: Comparison of home made bracket to the original.

27 For the attachment bracket that connects the rockshaft lift arm to the lower lift arm, these were found at the local hardware for $2 each. After some disassembly and cutting, they look like this.

28 After a little welding, a little bending, and a little reaming of the top hole to make the 5/8" bolt fit... Had to bend those brackets a little bit to make them fit just right. Here's a shot showing the lower lift arm, the "hardware store" bracket, and the upper rockshaft lift arm. You can just barely see the lower lift arm attachment bracket as well.

29 And now...(drum roll please)...finally...here is a shot of all home made components bolted up to the tractor.. Another view...

30 Still need to rig up some limiting chains and to pull everything back off, then primer and paint it. All the way down The lifting range is about 11" from all the way down to all the way up and will lift at least 170 lbs.

31 Here are all of the components of "Build Your Own 3pt Hitch": Costs: Steel: $48.00 Swivels: $6/ea. $36.00 Center lift link: $20.00 Paint/Primer: $ 8.00 Bolts/Nuts: $ 6.00 Chain: $ 2.50 Total: $ "Building it Yourself...Priceless" All mounted up!

32

33

Constitution Instructions

Constitution Instructions Constitution Instructions This kit will build a 1:48 scale hull for the USS Constitution frigate. The kit contains the following parts. 1/8 deck with laser etched deck lines 1/8 railing Ribs Center keel

More information

PPM-8240 JEEP XJ REAR SPRING HANGER BRACKET Version 1.1

PPM-8240 JEEP XJ REAR SPRING HANGER BRACKET Version 1.1 SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-8240 JEEP XJ REAR SPRING HANGER BRACKET Version 1.1 GENERAL NOTES: These instructions are also available on our website; www.synergymfg.com.

More information

To address this issue, Ariens Company has developed two cradle plates kits:

To address this issue, Ariens Company has developed two cradle plates kits: Date: August 21, 2012 No. B-2093 Service Bulletin Ariens Company 655 W. Ryan St. Brillion, WI 54110 www.gravely.com Product Family: Pro-Turn 400 Mowers Subject: Possible Foot Plate Weld Fracture Dealer

More information

JEEP CHEROKEE XJ DIY FRONT BUMPER ASSEMBLY INSTRUCTIONS

JEEP CHEROKEE XJ DIY FRONT BUMPER ASSEMBLY INSTRUCTIONS JEEP CHEROKEE XJ DIY FRONT BUMPER ASSEMBLY INSTRUCTIONS Please read the mounting instructions below carefully before attempting to install. Thank you for purchasing your new DIY Bumper from JcrOffroad!

More information

CHAINLESS ANCHORING SYSTEM USER MANUAL

CHAINLESS ANCHORING SYSTEM USER MANUAL CHAINLESS ANCHORING SYSTEM USER MANUAL Introduction..................................................... 1 Setting up the Chainless Anchoring System............................ 4 Set up Procedure............................................

More information

Step 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the seam joint is.

Step 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the seam joint is. WhiplashGV Instruction Manual Email: Brian@Blazermarine.com Phone: 513-598-1769 Step 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the

More information

SERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.

SERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding

More information

Soccer Goal. Model: SG20 Series. Installation, Operation and Maintenance Instructions

Soccer Goal. Model: SG20 Series. Installation, Operation and Maintenance Instructions Soccer Goal Model: SG20 Series Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE

More information

Divider Systems. Rear Tire Divider (RTD) Section 4. Model Years Model Years Model Years

Divider Systems. Rear Tire Divider (RTD) Section 4. Model Years Model Years Model Years Divider Systems Rear Tire Divider (RTD) Section 4 Model Years 1988 1993... 2-3 Model Years 1994 1996... 4-5 Model Years 1997 2010... 6-7 Model Years 2011 Present, Upper... 8-9 Model Years 2011 Present,

More information

PAY N PAK, 1/12 th Scale, Limited Sport Hydro P Sport Hydro

PAY N PAK, 1/12 th Scale, Limited Sport Hydro P Sport Hydro 1980 82 PAY N PAK, 1/12 th Scale, Limited Sport Hydro P Sport Hydro Introduction: The 1980 turbine Pay N Pak is a good subject for a model race boat. It has a low profile, mild pickle-fork setback, long

More information

Parts Manual. Scraper Hitches PH:

Parts Manual. Scraper Hitches PH: Parts Manual Scraper Hitches 12-18 1 Table of Contents A123299 Swivel Hitch 3 A1063527 Super Swivel Hitch 4 A125056 Yoke Hitch 5 A125057 Super Capacity Hitch 6 A125223 MDU Hitch 7 A123224 360 Swivel Hitch

More information

SUGGESTED SLIDE INSTALLATION PROCEDURE

SUGGESTED SLIDE INSTALLATION PROCEDURE SUGGESTED SLIDE INSTALLATION PROCEDURE DECKED is providing these instructions as a courtesy to its customers. While DECKED has attempted to ensure that these instructions are accurate and complete, DECKED

More information

BICYCLE ACCESS RAMP INSTALLATION INSTRUCTIONS. Customer Service all4cycling.com.au

BICYCLE ACCESS RAMP INSTALLATION INSTRUCTIONS. Customer Service all4cycling.com.au BICYCLE ACCESS RAMP INSTALLATION INSTRUCTIONS Customer Service 1300 429 254 all4cycling.com.au Thanks for buying our Bicycle Access Ramp! You re now the proud owner of the Bike Fixation Bicycle Access

More information

Fairlane & Meteor Instruction Package RC-114K. Rear Coilover Suspension Kit NOTE...

Fairlane & Meteor Instruction Package RC-114K. Rear Coilover Suspension Kit NOTE... ROD & CUSTOM Motorsports INCORPORATED 1962-1965 Fairlane & Meteor Instruction Package RC-114K Rear Coilover Suspension Kit NOTE... PLEASE READ ALL INSTRUCTIONS INCLUDED WITHIN THIS PACKAGE. IF AFTER READING

More information

Backboard and Rim Owners Manual

Backboard and Rim Owners Manual REQUIRED TOOLS AND MATERIALS: Two (2) Capable Adults Tape Measure Backboard and Rim Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. Step Ladder - 8ft. (2.4

More information

Deluxe Gourd Racks I D E G A. Parts List. Shown above are parts for the two-level, Deluxe Gourd Rack (DGR 12V)with 12 arms for vertically hung gourds.

Deluxe Gourd Racks I D E G A. Parts List. Shown above are parts for the two-level, Deluxe Gourd Rack (DGR 12V)with 12 arms for vertically hung gourds. Deluxe Gourd Racks H F K I D E J C G A Shown above are parts for the two-level, Deluxe Gourd Rack (DGR V)with arms for vertically hung gourds. Parts List Code Quantity A B C D E F G H I J 6, or 4 6, or

More information

SEADUCER BOATS GAS SPORT HYDRO

SEADUCER BOATS GAS SPORT HYDRO SEADUCER BOATS GAS SPORT HYDRO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 2 - Pkg. Of 440 push rod ends 2 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 30" flex

More information

Road Chain Catcher Installation Instructions (K13-001, K13-006, K SL1, K SL2)

Road Chain Catcher Installation Instructions (K13-001, K13-006, K SL1, K SL2) Road Chain Catcher Installation Instructions (K13-001, K13-006, K13-001-SL1, K13-001-SL2) Description: The K-Edge Road Chain Catcher series is designed to eliminate chain drop on the lowest chainring due

More information

SECTION 2 RING MOUNT

SECTION 2 RING MOUNT SECTION 2 RING MOUNT Rotax aircraft engines are manufactured and supported by Rotax GmbH of Austria. Read and understand the Rotax manuals completely before starting with the engine installation, as they

More information

Lock-N-Load. Bullet Feeder

Lock-N-Load. Bullet Feeder Lock-N-Load Bullet Feeder table of contents steps Overview... 2 List of required hand tools... 2 1: Mounting the Bullet Feeder to the Bench... 3 2: Mounting the Bullet Feed Hopper... 4 3: Bullet Feed Hopper

More information

Installation Instructions MODEL VSTI-A020 Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Versa Steel Inc. Guide Cables No

Installation Instructions MODEL VSTI-A020 Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Versa Steel Inc. Guide Cables No Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Guide Cables No Guide Cables 1 August 4, 2011 Assembly Instructions: (Shown with a 2 board, 12 ft kit) ITEM NO. PART NUMBER DESCRIPTION

More information

QUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift

QUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your

More information

RZR 900 Hitch Mount Plate

RZR 900 Hitch Mount Plate RZR 900 Hitch Mount Plate Polaris RZR 900 2015+ Part #: 5801119 Rev. 031017 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-278-7768 E-mail: sales-rtpro@sporttruckusainc.com SAFETY WARNING RT Pro

More information

OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL)

OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL) OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL) Table of Contents ASSEMBLY ASSEMBLY Pistol Bullet Feeder... Page 3 CHANGE-OVERS The Hornady Lock-N-Load Pistol Bullet Feeder is capable of feeding most

More information

FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions

FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions WARNING! WARNING! WARNING! THIS BASKETBALL SYSTEM IS SPRING LOADED AND SHIPPED UNDER TENSION. ATTEMPTING TO ASSEMBLE OR DISASSEMBLE ANY

More information

1/10 th Scale 1956 Ted Jones Classic Hydroplane

1/10 th Scale 1956 Ted Jones Classic Hydroplane 1/10 th Scale 1956 Ted Jones Classic Hydroplane Preparation These plans show outside sheeting of 3/32 balsa laminated with 1/64 birch ply. This makes a light and strong skin for this boat. Optionally you

More information

WEIGHT STACK ATTACHMENT. Assembly Manual (888) FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY

WEIGHT STACK ATTACHMENT. Assembly Manual (888) FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY WEIGHT STACK ATTACHMENT Assembly Manual DF835 (888) 258-0533 FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS

More information

Steps for W17, W14,W07, Wing Assembly Sonex #815

Steps for W17, W14,W07, Wing Assembly Sonex #815 CAUTION: This document is in no way a publication of Sonex Aircraft LLC. or any other corporation. All products mentioned are not necessarily recommended for use, but are included for informational purposes

More information

How to Replace Ball Joints

How to Replace Ball Joints How to Replace Ball Joints This is a big write up with a lot of pictures but I thought it would help some people. I know a lot of people have been having problems with ball joints so when I did mine I

More information

INSTALLATION INSTRUCTIONS FOR ROLLOVER PROTECTION SYSTEM (ROPS)

INSTALLATION INSTRUCTIONS FOR ROLLOVER PROTECTION SYSTEM (ROPS) INSTALLATION INSTRUCTIONS FOR ROLLOVER PROTECTION SYSTEM (ROPS) This manual contains assembly, operating, maintenance and safety instructions for your ROPS. Before Installing the ROPS or operating a machine

More information

Row Marker OEM /

Row Marker OEM / IMPORTANT: Your new row marker is designed to attach to the Troy-Bilt Hiller-Furrower attachment. If you don t have Hiller- Furrower, call us or visit www.troybilt.com to place an order: OEM-290-250 for

More information

Converting a 2006 Royal Enfield Classic to a Kick Start Only Machine. There are good reasons for not having an electric start.

Converting a 2006 Royal Enfield Classic to a Kick Start Only Machine. There are good reasons for not having an electric start. Converting a 2006 Royal Enfield Classic to a Kick Start Only Machine Reasons There are good reasons for not having an electric start. They are: 1. Reliability. There simply are fewer parts to fail. When

More information

Universal Elevator Mount Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI U.S.A.

Universal Elevator Mount Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI U.S.A. REQUIRED TOOLS AND MATERIALS: 2 Capable Adults Carpenter s Level 15 Tape Measure Pencil Universal Elevator Mount Owners Manual Customer Service Center N53 W2400 South Corporate Circle Sussex, WI 530 U.S.A.

More information

Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS

Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS 1 Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new Stand-N-Fish Kayak Fishing System. Once installed on your kayak the Stand-N-Fish will take your kayak fishing

More information

A. TO PREPARE THE MACHINE FOR USE.

A. TO PREPARE THE MACHINE FOR USE. INSTRUCTION MANUAL FOR THE ML120 STRINGING MACHINE. CONTENTS: A. TO PREPARE THE MACHINE FOR USE. 1. The assembly of frame with console and tooltray. 2. Fixing the lever of the tension unit. 3. Putting

More information

INSTRUCTIONS 360 Y-DROP HAGIE STS 2015

INSTRUCTIONS 360 Y-DROP HAGIE STS 2015 INSTRUCTIONS 60 Y-DROP HAGIE STS 05 INSTRUCTIONS 60 Y-DROP HAGIE STS 05 INTRODUCTION Before beginning, it s important to know where each mounting bracket fits relative to the row spacing involved. The

More information

A Low Cost Digital Angle Gage, version 3

A Low Cost Digital Angle Gage, version 3 A Low Cost Digital Angle Gage, version 3 By R. G. Sparber Copyleft protects this document. 1 Sometimes re-inventing the wheel has advantages. What you see here is just a variation on a sine bar. The accuracy

More information

Guide of the BrickIt balloon system for LEGO Blimps

Guide of the BrickIt balloon system for LEGO Blimps Guide of the BrickIt balloon system for LEGO Blimps Introduction At LEGO WORLD Zwolle 2010 we saw the blades on the LEGO Education Renewable Energy Add-On Set 9688 for the first time (See Figure 1). We

More information

2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions

2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions SECTION A: INTRODUCTION This unofficial set of installation instructions was written for a 2009 Hobie Getaway, using a 2012 Hobie Spinnaker Kit 20999020. Note from the Author: I had never seen this kit

More information

E Manual Self tacking system 30

E Manual Self tacking system 30 597-205-E 2015-12-09 Manual Self tacking system 30 1 Self tacking system 30, 443-200-10 A self-tacking jib makes life on board a lot easier, in particular for shorthanded crews. The jib sheet is led to

More information

E-trike Li Assembly Guide

E-trike Li Assembly Guide PREPARATION 1. Read this assembly manual BEFORE commencing assembly. 2. Carefully remove all the components and packaged hardware from the shipping boxes. 3. Unpack the contents of the large double box

More information

HermanMiller Aeron. New Aeron Disassembly for Recycling. Materials Identification and Segregation: Tools Required. Step 1

HermanMiller Aeron. New Aeron Disassembly for Recycling. Materials Identification and Segregation: Tools Required. Step 1 HermanMiller Aeron For more information about our products and services or to see a list of dealers, please visit us at www.hermanmiller.com or call 888-443 - 4357. 2016 Herman Miller, Inc., Zeeland, Michigan

More information

PRO1030 Bi-Directional Assembly Replacement

PRO1030 Bi-Directional Assembly Replacement PRO1030 Bi-Directional Assembly Replacement 1. Remove both side covers using the Crank and Cover Removal procedure. Fig. 1 2. Disconnect both brake cables (not shown) from the brake (S3611). (Fig. 1) 3.

More information

NO LATHE TRIKE HUBS. All content copyright AtomicZombie Extreme Machines. All rights reserved. 1

NO LATHE TRIKE HUBS. All content copyright AtomicZombie Extreme Machines. All rights reserved. 1 NO LATHE TRIKE HUBS First of all, thanks all of those who visit the Atomic Zombie forum and help others with advice and offer their great tips and tricks. There have been two alternative ideas posted in

More information

Trampoline & Enclosure Assembly Instructions

Trampoline & Enclosure Assembly Instructions Trampoline & Enclosure Assembly Instructions Safe user weight 330 lbs (150 kg) Version 718702 The information in this document is subject to change without notice. Copyright Springfree Trampoline Inc.

More information

INSTALLATION INSTRUCTIONS FOR: RE4548 JK FRONT COILOVER KIT

INSTALLATION INSTRUCTIONS FOR: RE4548 JK FRONT COILOVER KIT RUBICON EXPRESS 3290 MONIER CIR., RANCHO CORDOVA, CA. 95742 866-533-7706, www.rubiconexpress.com INSTALLATION INSTRUCTIONS FOR: RE4548 JK FRONT COILOVER KIT Safety Warning: Suspension systems or components

More information

Lectric Cycles Mid-Drive Electric Motor Installation

Lectric Cycles Mid-Drive Electric Motor Installation Lectric Cycles Mid-Drive Electric Motor Installation This write-up describes the installation of a Lectric Cycles electric motor. The model is the e-rad Mid-Drive 750 Watt conversion kit, installed on

More information

Assembly Instructions. -Cantilever Boat Lifts

Assembly Instructions. -Cantilever Boat Lifts Assembly Instructions -Cantilever Boat Lifts Winch Instruction Page Safety Information 1. The winch is built for the multipurpose of hauling and lifting operations. It is not to be used as a hoist for

More information

Riviera Draft Shaft Hole Boring

Riviera Draft Shaft Hole Boring Riviera Draft Shaft Hole Boring a. Height from bottom of hull thru the hull to the center of the drive shaft. This will be calculated. b. Height of drop of strut. The strut for the Riviera is 7.5 c. Distance

More information

SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT

SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 1 - Pkg. Of 440 push rod ends 1 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 24" flex shaft

More information

JARVIS. Model CPE Hock and Neck Cutter EQUIPMENT... TABLE OF

JARVIS. Model CPE Hock and Neck Cutter EQUIPMENT... TABLE OF 74 Hock and Neck Cutter EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page with Control Circuit. 4304003 only... 4304004 Balancer... 1350084 Control Circuit... 3350010 Air Hose (Yellow)... 3323003

More information

USER S MANUAL QUESTIONS? CAUTION. Model No. FMEX Serial No. Write the serial number in the space above for reference. Serial Number Decal

USER S MANUAL QUESTIONS? CAUTION. Model No. FMEX Serial No. Write the serial number in the space above for reference. Serial Number Decal Model No. FMEX81110.0 Serial No. Write the serial number in the space above for reference. USER S MANUAL Serial Number Decal QUESTIONS? If you have questions, or if parts are damaged or missing, please

More information

CRACKS IN THE WING by Fred Keip

CRACKS IN THE WING by Fred Keip CRACKS IN THE WING by Fred Keip As most of you know, my Sonerai IIL is old. On June 8 of 2011, she celebrated the 25 th anniversary of her first flight. She s also turned more than 1300 hours on her Hobbs

More information

Gurney Flap for WRX and STI w/low Profile Trunk Spoiler

Gurney Flap for WRX and STI w/low Profile Trunk Spoiler Gurney Flap for 2015+ WRX and STI w/low Profile Trunk Spoiler 2017-12-05 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced

More information

3190A NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS. Series MODEL NO

3190A NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS. Series MODEL NO NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS Series 30A Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram

More information

TOYOTA TACOMA 2005 TOW HITCH Preparation. Part Number: PT

TOYOTA TACOMA 2005 TOW HITCH Preparation. Part Number: PT Preparation Part Number: PT791 04050 Kit Contents 1 1 Hitch Center Section 2 1 LH Frame bracket 1 RH Frame Bracket 4 2 Auxiliary Bracket Hardware Bag Contents 1 6 Hex Head Bolt, M12 x 1.2 (black) 2 6 Nut,

More information

We hope you ll enjoy the Drifter as much as we have! Scott DeTray Model Aero Specifications:

We hope you ll enjoy the Drifter as much as we have! Scott DeTray Model Aero Specifications: We are excited to bring you the Drifter RC airboat. You re probably thinking it doesn t fly so what is Model Aero thinking??? We have always liked RC vehicles of all types and have had a fondness for airboats

More information

SCOUT DECK ANCHOR 3 1/4" BONDING SCREW

SCOUT DECK ANCHOR 3 1/4 BONDING SCREW SCOUT DECK ANCHOR 16" 16" 1" X 4" ANCHOR BOLT (4) 10" 3 1/8" 5" 6" MIN COPPER WIRE TO ATTACH TO BONDING GRID 3 1/4" BONDING SCREW CONCRETE DECK SPECIFICATIONS: THE AQUA CREEK PRODUCTS' SCOUT DECK ANCHOR

More information

Trilogy Theory of Operation

Trilogy Theory of Operation INSTALLATION & OVERVIEW... 2 Load Height... 2 Approach Angle... 2 Footprint... 3 Protrusion... 3 Mounting the... 4 General Torque Specs... 4 OPERATION OF BIKE RACK... 5 Loading Bikes... 5 Unloading Bikes...

More information

Residential Garage Door WARNING

Residential Garage Door WARNING Residential Garage Door INFORMATION EZ-SET TORSION S TORSION S EXTENSION S Improper Installation or Door Position Can Result in Serious Injury or Death. Read and understand all instructions before you

More information

TURF VENTILATOR ATTACHMENT ASSEMBLY KIT INSTRUCTION BOOKLET

TURF VENTILATOR ATTACHMENT ASSEMBLY KIT INSTRUCTION BOOKLET TURF VENTILATOR ATTACHMENT ASSEMBLY KIT INSTRUCTION BOOKLET Wood Bay Turf Technologies, 2012 1 PURPOSE OF THE KIT The purpose of this greensiron 3900, turf VENTILATOR Kit is to enable owners of our turf

More information

S110 Steel Level Panel Installation Instructions

S110 Steel Level Panel Installation Instructions S110 Steel Level Panel Installation Instructions NOTE: Fairway Architectural Railing Solutions will not be held liable for incorrect or unsafe installations by installer. It is the installer s resposibility

More information

Detroit Speed, Inc. Rear Coilover Conversion Kit Camaro/Firebird P/N: &

Detroit Speed, Inc. Rear Coilover Conversion Kit Camaro/Firebird P/N: & Detroit Speed, Inc. Rear Coilover Conversion Kit 1982-02 Camaro/Firebird P/N: 042440 & 042441 The Detroit Speed Inc., Rear Coilover Conversion Kit allows the latest in coilover spring/shock technology

More information

BRONZE BUSHING REPLACEMENT PROCEDURE DN345 & NL450C

BRONZE BUSHING REPLACEMENT PROCEDURE DN345 & NL450C 1 BRONZE BUSHING REPLACEMENT PROCEDURE V.2 12/3/2014 DN345 & NL450C 2 Safety Instructions Removing Walking Beams 3 1. Position spreader on a flat concrete surface capable of supporting weight of spreader

More information

Cover EX Installation Instructions

Cover EX Installation Instructions Cover EX Installation Instructions 1. Lay out all the parts and verify that they are all present according to the Cover EX Parts and Hardware List. See Fig 1. Call 800-730-7727 for all replacement and

More information

BOTTOM BRACKET BEARINGS

BOTTOM BRACKET BEARINGS BOTTOM BRACKET BEARINGS This basic tutorial will demonstrate the workings of a typical 3 piece bottom bracket, showing the removal and installation of the various components that make up the bearing system.

More information

w w w.ro swellmarine. com Part 1 Installation Part # C # C

w w w.ro swellmarine. com Part 1 Installation Part # C # C w w w.ro swellmarine. com Pro Bimini Part 1 Installation Part # C915-119151 # C915-119152 Information: info@roswellmarine.com If you have any questions please call : 1-321-638-1331 REV 16-JUL-18 Moomba

More information

IMPORTANT: RECEIVING INSTRUCTIONS:

IMPORTANT: RECEIVING INSTRUCTIONS: Instruction Sheet Sidewinder Mechanical Bender IMPORTANT: RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any shipping damage is found, notify carrier at once.shipping damage

More information

BARRIER OFFSET 0" A 6" 6" A 12" 12" A 26" A 26" 3A OR 4A L OR S * ** L OR S L OR S

BARRIER OFFSET 0 A 6 6 A 12 12 A 26 A 26 3A OR 4A L OR S * ** L OR S L OR S ACCEPTABLE (TCB) TYPES AND ANCHORING DETAILS BASED ON UNDERLYING SURFACE TYPE AND BARRIER OFFSET FROM DROP-OFF BARRIER OFFSET UNDERLYING SURFACE 0" A 6" 6" A 12" 12" A 26" A 26" TCB TYPE DETAIL TCB TYPE

More information

310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment

310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment OPERATOR S MANUAL FOR MORSE TILT-TO-LOAD DRUM ROTATOR SAFETY INFORMATION: While Morse Manufacturing Co. drum handling equipment is engineered for safety and efficiency, a high degree of responsibility

More information

THOR 10 HAMMER CAGE INSTRUCTIONS

THOR 10 HAMMER CAGE INSTRUCTIONS 75 " 7m 78 4" m 6" 8.8m 45 ".70m 4.9deg 6 4" 6m 44 4".67m 75 " 7m 9 4" 0m 44".m 497 4".64m The 70, Thor Hammer Cage, consists of four heavy duty aluminum net poles. The unique pole structure reduces the

More information

F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN F-1281-R LOWER RIGHT SKIN F-1208-R FUSELAGE FRAME

F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN F-1281-R LOWER RIGHT SKIN F-1208-R FUSELAGE FRAME F-1282-R BOTTOM RIGHT SKIN F-1283C J-STIFFENER F-1278 TOP SKIN F-00009-L ADAHRS BRACKET F-00009-R ADAHRS BRACKET F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN SECTION 10: TAILCONE F-1279-L UPPER LEFT

More information

InstallatIon and owner s InstrUCtIons

InstallatIon and owner s InstrUCtIons InstallatIon and owner s InstrUCtIons Wall Mount Series Adjustable and Fixed Height Goal Systems table of Contents Safety Instructions... 2 Goal Specifications... 3 Frame Attachment... 4 Frame Assembly

More information

Livestock Equipment Bale Movers/ Bale Spears. Tractor Linkage. Grade 5 & 8 Hitch Pins. Tractor Linkage

Livestock Equipment Bale Movers/ Bale Spears. Tractor Linkage. Grade 5 & 8 Hitch Pins. Tractor Linkage Hooking a piece of equipment to your tractor? Our selection of hitch pins, locking pins, lift arm/top link parts, PTO adapters will keep things connected. Make sure you have an SMV sign to keep everyone

More information

THE GARRISON BINDER ...

THE GARRISON BINDER ... Did you ever wonder why (to quote Andy Rooney) the Garrison binder is for many rodmakers the source of contentious problems while other rodmakers never seem to have problems. One of the primary reasons

More information

RADIUS ROD BUSHING SET

RADIUS ROD BUSHING SET RADIUS ROD BUSHING SET These are designed to allow your front suspension to operate much more freely than the factory units, with less maintenaance. STICKSION could be a key word here. The front end will

More information

Repair instructions. Pivot bushing replacement. XL-AS10001RM-en-DE Rev B

Repair instructions. Pivot bushing replacement. XL-AS10001RM-en-DE Rev B Repair instructions Pivot bushing replacement XL-AS10001RM-en-DE Rev B Table of contents Table of contents 1 General information... 3 1.1 Safety information...3 1.2 Legal information...4 1.3 Order and

More information

6146XX-X OPEN STYLE HOSE REELS

6146XX-X OPEN STYLE HOSE REELS OPERATOR S MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE 6146XX-XXX OPEN STYLE HOSE REELS LOW, MEDIUM & HIGH PRESSURE (FOR AIR, WATER & PETROLEUM PRODUCTS) 6146XX-X RELEASED: 2-5-90 REVISED:

More information

REPLACING THE AFT RUDDER CABLES

REPLACING THE AFT RUDDER CABLES REPLACING THE AFT RUDDER CABLES Note: You must have the assistance of a qualified Aircraft Mechanic to perform this procedure. A logbook entry with the mechanics signature is required. Please read these

More information

RBI Solar One-Piece Ground Mount Solution GM-GS

RBI Solar One-Piece Ground Mount Solution GM-GS Solar Mounting System Installation Guide RBI Solar One-Piece Ground Mount Solution GM-GS Ballasted Ground Mount System RBI Solar 1292 Logan Circle NW Atlanta, GA 30318 513-618-7240 info@rbisolar.com OVERVIEW

More information

SECTION 23iS/U: SIDE SKINS

SECTION 23iS/U: SIDE SKINS SECTION 23iS/U: SIDE SKINS F-1203G-R BULKHEAD SIDE CHANNEL F-01248-R-1 ARM REST F-01205D SEAT BACK ADJUSTMENT GUIDE, 4 PLACES F-01205B-1 ROLL BAR ATTACH PLATE, F-01248B-1 FUSELAGE PIN LATCH, F-01204J BULKHEAD

More information

Installation and Training Manual

Installation and Training Manual AirForce1 Tower Kit Installation and Training Manual FuturEnergy Limited Ettington Park Business Centre Stratford upon Avon CV37 8BT +44 (0)1789 451070 Table of Contents Safety Notes... 3 Parts Supplied

More information

Installing N-Strike Recon CS-6 Stage 1 and Stage 2 Performance Kits

Installing N-Strike Recon CS-6 Stage 1 and Stage 2 Performance Kits Installing N-Strike Recon CS-6 Stage 1 and Stage 2 Performance Kits The Nerf N-Strike Recon CS-6 is a currently available blaster that is relatively easy to modify. The guys at Orange Mod Works have produced

More information

Vac Bagger Wheelhorse 42 and 48 Mowers for Classic Garden Tractors

Vac Bagger Wheelhorse 42 and 48 Mowers for Classic Garden Tractors Form No. -80 Vac Bagger Wheelhorse and 8 Mowers for Classic Garden Tractors Model No. 790 000000 & Up Operator s Manual Domestic English (EN) Contents Page Introduction................................

More information

#59114 Rola 2-Bike Rack Carrier (Shown Assembled) (A) (C) (B)

#59114 Rola 2-Bike Rack Carrier (Shown Assembled) (A) (C) (B) Use for Parts: #59114 Rola -Bike Rack System #59115 Rola 1-Bike Add-On TOOLS REQUIRED 10mm or 13/3 Socket & Wrench #59114 Rola -Bike Rack Carrier (Shown Assembled) Tray Attachment Hardware: (3) Plastic

More information

SASK-A-POLE OWNERS AND USERS MANUAL

SASK-A-POLE OWNERS AND USERS MANUAL SASK-A-POLE OWNERS AND USERS MANUAL GENERAL INFORMATION The Saskatchewan Abilities Council s Sask-a-Pole accessibility and transfer aid is designed to help provide safe and easy access to chairs, beds,

More information

Blazer Marine, Whiplash Sport Hydro

Blazer Marine, Whiplash Sport Hydro Blazer Marine, Whiplash Sport Hydro Thank you for choosing to build the Whiplash Sport Hydro. We have spent over 12 years perfecting this design, and finally we are making it available to the world. We

More information

SLIDING RAIL SYSTEM 208-580-1904 www.fishfighterproducts.com FFP sliding Rail system The FFP Sliding Rail system will allow you to easily adjust the location of your rod holders, tackle trays, or just

More information

! CAUTION! ! WARNING! General Information

! CAUTION! ! WARNING! General Information Great Plains Mfg., Inc. Installation Instructions Used with: 2SF24, 24-Foot Two-Section Drill General Information Two-Section, Hydraulic Folding Marker 2SF30, 30-Foot Two-Section Drill 2SBM30, 30-Foot

More information

VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns , , , , , )

VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns , , , , , ) VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns 3714022, 3714028, 3714034, 3714040, 3714043, 3714046) REIMANN & GEORGER CORPORATION MARINE PRODUCTS BUFFALO, NY P/N 6112103 04/09/18 1 SAFETY 1.1 INTRODUCTION

More information

632 AccuPro Set-up & Operation

632 AccuPro Set-up & Operation 632 AccuPro Set-up & Operation Always check: Reel & Roller bearings Bent or broken blades Make sure the reel spins freely in the frame Place the Reel Into the Machine There are three lifting options for

More information

Rekluse Motor Sports. TCS Clutch Baskets CRF 450R/X CR 250R

Rekluse Motor Sports. TCS Clutch Baskets CRF 450R/X CR 250R Rekluse Motor Sports TCS Clutch Baskets CRF 450R/X 2002 2008 CR 250R 1992 2006 Installation Guide Copyright 2006 Rekluse Motor Sports TCS Revision 1.000 RMS 4113 195-4113 Manual Revision: 081606 Rekluse

More information

Blazer Marine, Whiplash Sport 40

Blazer Marine, Whiplash Sport 40 Blazer Marine, Whiplash Sport 40 Thank you for choosing to build the Whiplash 40. We have spent over 12 years perfecting this design, and finally we are making it available to the world. We are excited

More information

Retractable Security Cover for a Swim Spa

Retractable Security Cover for a Swim Spa Parts List Retractable Security Cover Kit 3" PVC pipe Leading edge Cover Track (pre-attached to Swim Spa) Optional cover pump (for outdoor installations) Rocky Roller Kit 2 Roller A-Frame Brackets 1/2"

More information

Import Bike Rack OEM INSTALLATION MANUAL

Import Bike Rack OEM INSTALLATION MANUAL Import ike Rack OEM INSTLLTION MNUL TLE OF ONTENTS System Information 2 Safety Information 2 Resources Required 3 Preparation 3 Under umper ttachment 3 Over umper ttachment 3 Installation 3 Under umper

More information

TECH SHEET ORANGE PIVOT TOOL INSTRUCTIONS

TECH SHEET ORANGE PIVOT TOOL INSTRUCTIONS page 1 ORANGE PIVOT TOOL INSTRUCTIONS This is a guide of how to change the pivot bearings on an Orange frame with a bore style pivot axle. 4 8 Bore Type Pivot Axle Horiz-Hold Type Pivot Axle Please read

More information

Apex M&P Barrel Fit Guide ALL OF THE FOLOWING OPERATIONS ARE TO BE DONE WITH ABSOLUTELY ZERO LIVE AMMUNITION PRESENT.

Apex M&P Barrel Fit Guide ALL OF THE FOLOWING OPERATIONS ARE TO BE DONE WITH ABSOLUTELY ZERO LIVE AMMUNITION PRESENT. Familiarization Free floating barrels like most polymer frame pistols have, use 6 contact points o Barrel hood The extension of the chamber coming back over the top of a chambered round to make contact

More information

15000 Series Exhausting Arm - Wall Mount Models: 15076/15106/15146

15000 Series Exhausting Arm - Wall Mount Models: 15076/15106/15146 Operation and Maintenance Manual 15000 Series Exhausting Arm - Wall Mount Models: 15076/15106/15146 MONOXIVENT - SOURCE CAPTURE SYSTEMS - info@ Oct. - 2015 Receiving Assembly Information 15000 Series Exhausting

More information

Big Ride ASSEMBLY AND INSTALLATION INSTRUCTIONS * * C A U T I O N * *

Big Ride ASSEMBLY AND INSTALLATION INSTRUCTIONS * * C A U T I O N * * Big Ride ASSEMBLY AND INSTALLATION INSTRUCTIONS * * C A U T I O N * * S.R. SMITH BIG RIDE SLIDES ARE MANUFACTURED FOR INSTALLATION AND USE ON INGROUND SWIMMING POOLS ONLY. THE BIG RIDE IS NEVER TO BE INSTALLED

More information

Using Your Bike Friday : Folding Rear Rack

Using Your Bike Friday : Folding Rear Rack Using Your Bike Friday : Folding Rear Rack Green Gear Cycling, Inc. 3364 W. 11th Ave. Eugene, OR 97402 800-777-0258 USA & Canada +1-541-687-0487 Int l +1-541-687-0403 Fax www.bikefriday.com info@bikefriday.com

More information