fermacell AESTUVER fire-protection boards
|
|
- Abel Wade
- 6 years ago
- Views:
Transcription
1 fermacell AESTUVER fire-protection boards Classification of the fire resistance of structural steel members R0498b Datum:
2 P.O. Box ZN Bleiswijk Brandpuntlaan Zuid NZ Bleiswijk The Netherlands OF THE FIRE RESISTANCE IN ACCORDANCE WITH EN :2007+A1:2009 OF STRUCTURAL STEEL MEMBERS PROTECTED BY AESTUVER BOARDS Classification no. Sponsor Product name Düsseldorfer Landstrasse Duisburg Germany Aestuver boards Prepared by Efectis Nederland BV Notified body no Authors Ir. T. Rakovec P.W.M. Kortekaas Project number Date of issue Number of pages 13 All rights reserved. No part of this publication may be reproduced and/or published without the previous written consent of Efectis Nederland. Submitting the report for inspection to parties who have a direct interest is permitted. In case this report was drafted on instructions, the rights and obligations of contracting parties are subject to either the Standard Conditions of Efectis Nederland or the relevant agreement concluded between the contracting parties Efectis Nederland BV Page 1 / 13
3 CONTENTS 1. INTRODUCTION DETAILS OF CLASSIFIED PRODUCT General Description TEST REPORTS, ASSESSMENT REPORT AND TEST RESULTS IN SUPPORT OF THE Test & assessment report Results AND FIELD OF APPLICATION Reference of classification Classification Field of application Limitations... 5 APPENDIX A: DESIGN TABLES... 6 APPENDIX B: DRAWINGS This report consists of thirteen pages and may only be used in its entirety. Page 2 / 13
4 1. INTRODUCTION This classification report gives a classification of structural steel members protected by Aestuver boards in accordance with the procedures given in EN :2007+A1: DETAILS OF CLASSIFIED PRODUCT 2.1 GENERAL The Aestuver boards are defined as boxed applied passive protection to steel members. In total 5 tests were carried out at the laboratory of Efectis Nederland on the following dates: Test 1: 26/04/2013 Test 2: 08/05/2013 Test 3: 20/06/2013 Test 4: 02/10/2013 Test 5: 14/10/ DESCRIPTION The product is fully described in the test reports no Efectis-R0116a and 2013-Efectis-R0343a Protection system The applied fire protection system consists of a single layer boxed protection of Aestuver board. All connections of the boards are created by staples. The cladding Aestuver boards is connected to noggings which consist of a double layer of Aestuver boards of dimensions 2x20 mm x 150 mm x distance between beam flanges (cladding more than 15 mm thick) 2x15 mm x 150 mm x distance between beam flanges (cladding 15 mm thick) The centre-to-centre distance of the noggings is 1250 mm. Outer board of the nogging consist of two wedges lower wedge is of height 4/5 and the upper wedge of height 1/5 of the overall height. The inner board of the nogging is made of one full height board. Scheme of the fire protection system is in Appendix B Steel sections In total 2 loaded beams, 2 reference beams and 11 short I-section beams protected by Aestuver boards were tested. 3. TEST REPORTS, ASSESSMENT REPORT AND TEST RESULTS IN SUPPORT OF THE 3.1 TEST & ASSESSMENT REPORT Name of laboratory Name of sponsor Report ref. No. Test method Efectis Nederland BV Test report: 2013-Efectis-R0116a Efectis Nederland BV Test report: 2013-Efectis-R0343a Efectis Nederland BV Assessment report: 2013-Efectis-R0343d EN :2013 EN :2013 EN :2013 This report consists of thirteen pages and may only be used in its entirety. Page 3 / 13
5 3.2 RESULTS Test method, number and date of report EN : Efectis-R0116a September 2013 EN : Efectis-R0343a EN : Efectis-R0343d Parameter Specimens Fire exposure Number of exposed sides Support conditions Length of the loaded beam Applied load to the loaded beam Loadbearing capacity Specimens Fire exposure Number of exposed sides Length of the short I-section beam Required thickness of protection related to design temperature fire resistance and section factor Results Loaded beams, reference beams standard temperature/time curve 3 Simply supported 4500 mm 60 % of the design moment resistance Test 1 (50 mm): 188 min Test 2 (15 mm): 77 min Short I-section beams standard temperature/time curve mm Tabulated data in Appendix A 4. AND FIELD OF APPLICATION 4.1 REFERENCE OF The classification has been carried out in accordance with Clause 7 of EN :2007 +A1:2009. This report consists of thirteen pages and may only be used in its entirety. Page 4 / 13
6 4.2 The element structural steel member protected by Aestuver boards is classified according to the following performance parameter and classes: Fire resistance classification: R 15 R FIELD OF APPLICATION This classification is valid for the following end use of applications: Classes of fire resistance R 15, R 20, R 30, R 45, R 60, R 90, R 120, R 180, R 240 Design steel temperature 350 ºC θ a 750 ºC Permitted section factor range: Permitted protection thickness: 61.8 m -1 A m /V m -1 For section factors below the minimum permitted section factor the same protection thickness as that applied to the minimum section factor must be applied mm d p 52.5 mm Grades of steel: Any structural grade (S designation) according to EN (excluding S185); engineering grades (E designation) shall not be used; the results may be also applicable to fabricated sections The maximum beam web depth 331 mm + 50 % = mm Number of exposed sides 3 The distance of Aestuver boards from a steel member (tested distance 3 mm at the vertical sides and 10 mm at the lower flange of the beam): 0 mm to 53 mm at the vertical sides 5 mm to 60 mm at the lower flange with no change of fixing 4.4 LIMITATIONS This classification document does not represent type approval or certification of the product. Signed Approved Ir. T. Rakovec Project Leader Fire Engineering P.W.M. Kortekaas Project Leader Resistance to Fire This report consists of thirteen pages and may only be used in its entirety. Page 5 / 13
7 APPENDIX A: DESIGN TABLES Table A.1: Required thickness of fire protection: R 30 Table A.2: Required thickness of fire protection: R 60 Table A.3: Required thickness of fire protection: R 90 Table A.4: Required thickness of fire protection: R 120 Table A.5: Required thickness of fire protection: R 180 Table A.6: Required thickness of fire protection: R 240 This report consists of thirteen pages and may only be used in its entirety. Page 6 / 13
8 Section factor (m -1 ) Fire resistance classification R 30 Design temperature 350 ºC 400 ºC 450 ºC 500 ºC 550 ºC 600 ºC 650 ºC 700 ºC 750 ºC Thickness of fire protection material to maintain steel temperature below design temperature (mm) Table A.1 Required thickness of fire protection: R 30 This report consists of thirteen pages and may only be used in its entirety. Page 7 / 13
9 Section factor (m -1 ) Fire resistance classification R 60 Design temperature 350 ºC 400 ºC 450 ºC 500 ºC 550 ºC 600 ºC 650 ºC 700 ºC 750 ºC Thickness of fire protection material to maintain steel temperature below design temperature (mm) Table A.2 Required thickness of fire protection: R 60 This report consists of thirteen pages and may only be used in its entirety. Page 8 / 13
10 Section factor (m -1 ) Fire resistance classification R 90 Design temperature 350 ºC 400 ºC 450 ºC 500 ºC 550 ºC 600 ºC 650 ºC 700 ºC 750 ºC Thickness of fire protection material to maintain steel temperature below design temperature (mm) Table A.3 Required thickness of fire protection: R 90 This report consists of thirteen pages and may only be used in its entirety. Page 9 / 13
11 Section factor (m -1 ) Fire resistance classification R 120 Design temperature 350 ºC 400 ºC 450 ºC 500 ºC 550 ºC 600 ºC 650 ºC 700 ºC 750 ºC Thickness of fire protection material to maintain steel temperature below design temperature (mm) Table A.4 Required thickness of fire protection: R 120 This report consists of thirteen pages and may only be used in its entirety. Page 10 / 13
12 Section factor (m -1 ) Fire resistance classification R 180 Design temperature 350 ºC 400 ºC 450 ºC 500 ºC 550 ºC 600 ºC 650 ºC 700 ºC 750 ºC Thickness of fire protection material to maintain steel temperature below design temperature (mm) Table A.5 Required thickness of fire protection: R 180 This report consists of thirteen pages and may only be used in its entirety. Page 11 / 13
13 Section factor (m -1 ) Fire resistance classification R 240 Design temperature 350 ºC 400 ºC 450 ºC 500 ºC 550 ºC 600 ºC 650 ºC 700 ºC 750 ºC Thickness of fire protection material to maintain steel temperature below design temperature (mm) Table A.6 Required thickness of fire protection: R 240 This report consists of thirteen pages and may only be used in its entirety. Page 12 / 13
14 APPENDIX B: DRAWINGS Figure B.1 Scheme of the fire protection system This report consists of thirteen pages and may only be used in its entirety. Page 13 / 13
15 AESTUVER Düsseldorfer Landstraße 395 D Duisburg Germany For the latest version of this brochure please visit our website Technical modifications subject to changes. Last updated: 12/2013 The most recent edition applies. Should you require additional information, please contact our fermacell customer service. fermacell customer service: phone +49 (0) fax +49 (0) fermacell is a registered trademark and a company of the XELLA group.
fermacell AESTUVER fire-protection boards
fermacell AESTUVER fire-protection boards Classification of the fire resistance of structural steel members R0498a Datum: P.O. Box 554-2665 ZN Bleiswijk Brandpuntlaan Zuid 16-2665 NZ Bleiswijk The Netherlands
More informationEN1279 part 3 assessment of insulating glass: IGU with Duralite sealant
TNO Quality Services BV TNO report De Rondom 1 P.O. Box 6235 5600 HE Eindhoven The Netherlands TQS-RAP-07-271 EN1279 part 3 assessment of insulating glass: IGU with Duralite sealant Date February 7, 2007
More informationF-08 HIGH-PRESSURE HOSE USED IN CO2 SYSTEM
Guideline No.: F-08(201510) F-08 HIGH-PRESSURE HOSE USED IN CO2 SYSTEM Issued date: October 20,2015 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements,
More informationVENTILATOR OPTIONS. Please visit our web page to view all the available options and for a specification.
Seefire Natural Louvred Ventilator Seefire is a natural louvred ventilator that is available in a wide range of sizes, louvre options and control options. Seefire has been exhaustively tested and certified
More informationProcess Filtration From Pure to Sterile
From Pure to Sterile MAIN FEATURES & BENEFITS: Developed for the sterile filtration of air and gases in compressed gas applications as well as venting applications. High dirt holding capacity at a low
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12385-2:2003 Terastraadist trossid. Ohutus. Osa 2: Määratlused, nimetused ja klassifikatsioon Steel wire ropes - Safety - Part 2: Definitions, designation and classification EESTI
More informationFlexible hoses - Non-metallic materials
CLASS PROGRAMME Type approval DNVGL-CP-0183 Edition December 2015 The electronic pdf version of this document, available free of charge from http://www.dnvgl.com, is the officially binding version. FOREWORD
More informationWP2 Fire test for toxicity of fire effluents
Pagina 3 di 89 TRA SFEU VTT 22.6.2009 v.2 WP2 Fire test for toxicity of fire effluents Task 2.1.2 Development of small-scale test method for fire effluents Step 1: Use of modeling Plans according to DoW:
More informationCertificate No.: 2531 CPR CSC10016 Issue date:
CERTIFICATE OF CONSTANCY OF PERFORMANCE Issued by DBI Certification, notified body No. 2531. In compliance with Regulation 305/2011/EU of the European Parliament and of the Council of 9 March 2011 (the
More information01 18/11/2013 correction of the reference of the product 1 4 5
The signed original report cancels all results and draft documents previously submitted. Each updated version of the report supersedes all previous ones. All void copies must be returned to CETIAT or destroyed.
More informationSTANDARD SPECIFICATION FOR SPLIT TEES (HOT TAP MATERIAL)
STANDARD SPECIFICATION FOR SPLIT TEES (HOT TAP MATERIAL) TEE (HOT TAPPING MATERIAL) S-04-02-040 Page 1 of 7 1.0 SCOPE This specification covers the basic requirements for the design, manufacture and supply
More informationPaper Tiger Catamaran International Association MEASUREMENT FORM
Paper Tiger Catamaran International Association MEASUREMENT FORM Amended June 2000: July 2002: April 2012 Name of boat: Sail No: Owner s name: Owner s address: Postcode: Phone: (H) (B) (Mob.) Email: Owner
More informationISO 4344 INTERNATIONAL STANDARD. Steel wire ropes for lifts Minimum requirements. Câbles en acier pour ascenseurs Exigences minimales
INTERNATIONAL STANDARD ISO 4344 Second edition 2004-02-01 Steel wire ropes for lifts Minimum requirements Câbles en acier pour ascenseurs Exigences minimales Reference number ISO 2004 PDF disclaimer This
More informationEffective Date: May 2017 Void After: May Product: Press and Nail Connections File No. M-8332
IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the
More informationCode Compliance Research Report CCRR-0145
Code Compliance Research Report CCRR-0145 Issue Date: 11-16-2009 Revision Date: 11-29-2018 Renewal Date: 11-18-2019 DIVISION: 05 - Metals Section: 05 50 00 Metal Fabrications Marshall Stamping Company
More informationPH01 Perfusion Cannula Manual
PH01 Perfusion Cannula Manual Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted without the express written permission of Multi
More informationReg No: 1999/027771/07 ACCREDITED AND APPROVED TEST LABORATORY IN TERMS OF ARP 0108: REGULATORY REQUIREMENTS FOR EXPLOSION PROTECTED APPARATUS
Government Approved Test Laboratory (Previously AIA) Reg No: 1999/027771/07 ACCREDITED AND APPROVED TEST LABORATORY IN TERMS OF ARP 0108: REGULATORY REQUIREMENTS FOR EXPLOSION PROTECTED APPARATUS ZEST
More informationPressure and Flow Control Valves DBGM, German and European Patents
Pressure and Flow Control Valves DBGM, German and European Patents Absolutely Reliable Pressure and Flow Control In water mains of sizes DN 50 to DN 150, ERHARD Control Valves in straight or angle pattern
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10464 First edition 2004-08-15 Gas cylinders Refillable welded steel cylinders for liquefied petroleum gas (LPG) Periodic inspection and testing Bouteilles à gaz Bouteilles rechargeables
More informationCode Compliance Research Report CCRR-0145
Code Compliance Research Report CCRR-0145 Issued: 11-16-2009 Renewal Due: 11-18-2018 Revised: 11-28-2017 DIVISION: 05 - Metals Section: 05 50 00 Metal Fabrications MARSHALL STAMPING COMPANY 355 Glade Mills
More informationStructurals Rationalised sizes of Beams/Joists, Channels and Angles
Structurals Rationalised sizes of Beams/Joists, Channels and Angles Section Dimensions Sectional Weight Length mm kg/m m Beams/Joists Beams Durgapur Steel Plant 175 x 85 x 5.8 19.6 Std length 200 x 100
More information6-5 Maintenance Manual
Non Return Valve 6-5 Maintenance Manual Contents 1. PRODUCT DESCRIPTION... 1 1.1 How it works... 1 1.2 Overall dimensions... 3 1.3 Technical datasheet... 4 1.3.1 Push flow situation... 4 1.3.2 Pull flow
More informationREGULATIONS 1. GENERAL CONDITIONS
1 1. GENERAL CONDITIONS REGULATIONS 1.1 The Ski Meeting Interbancario Europeo is carried out on own initiative and under the assistance of the Standing Committee which is the international governing and
More informationTranslation Principles of testing and certification for insulating hose assemblies on cable cutting devices
Translation Principles of testing and certification for insulating hose assemblies on cable cutting devices Status as of 2014-01 Principles of testing Insulating hose assemblies on cable cutting devices
More informationISO/TS TECHNICAL SPECIFICATION. Stainless steels Chemical composition. Aciers inoxydables Composition chimique. First edition
TECHNICAL SPECIFICATION ISO/TS 15510 First edition 2003-04-15 Stainless steels Chemical composition Aciers inoxydables Composition chimique Reference number ISO 2003 PDF disclaimer This PDF file may contain
More informationFLOW CONDITIONER «EMIS-VEKTA 1200» EMIS-VEKTA 1200.UM.PS v User manual Passport. «EMIS», CJSC Russia, Chelyabinsk
EMIS-VEKTA 1200.UM.PS 27.11.2012 v1.0.5 FLOW CONDITIONER User manual Passport www.emis-kip.ru «EMIS», CJSC Russia, Chelyabinsk Disclaimer "EMIS", CJSC reserves the right to make changes in the design and
More informationCERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES
9319 1 71-9319 USA/9319/B(U)F-96 1 OF 6 2. PREAMBLE a. This certificate is issued to certify that the package (packaging and contents) described in Item 5 below meets the applicable safety standards set
More informationInformal document regarding progress of CEN standards for reference in RID/ADR
Joint Meeting of the RID Safety Committee and the Working Party on the Transport of Dangerous Goods (Berne, 13-24 March 2000) Informal document regarding progress of CEN standards for reference in RID/ADR
More informationTECHNICAL MANUAL. COPRA Anchoring Coupler. For Smart Bolted Connections
TECHNICAL MANUAL Anchoring Coupler For Smart Bolted Connections Version: PEIKKO GROUP 03/2017 Anchoring Coupler For bolted connections Multi-purpose anchoring system for all bolted connections Simplifi
More information3.1 T AND TKH FERRULES EUROPEAN STANDARD SYSTEM EN
TURNBACK FERRULES T ferrule TKH ferrule 3.1 T AND TKH FERRULES EUROPEAN STANDARD SYSTEM EN 134113 GENERAL DESCRIPTION The aluminium ferrules, type T and type TKH correspond to the European standard for
More informationEvaluating the Design Safety of Highway Structural Supports
Evaluating the Design Safety of Highway Structural Supports by Fouad H. Fouad and Elizabeth A. Calvert Department of Civil and Environmental Engineering The University of Alabama at Birmingham Birmingham,
More informationQPF Pneumatic Fenders. Operation Manual A EUROTECH BENELUX COMPANY
QPF Pneumatic Fenders Operation Manual A EUROTECH BENELUX COMPANY Introduction The QuayQuip QPF Pneumatic Fender has an air-filled cylindrical body with hemispherical ends. One or both ends may have a
More informationSUPPORTING NOTES FOR THE EVALUATION OF UNBOUND ROAD BASE AND SUB-BASE AGGREGATES
SUPPORTING NOTES FOR THE EVALUATION OF UNBOUND ROAD BASE AND SUB-BASE AGGREGATES (These notes are guidelines only and must not be included in the Contract Documents). 1. SCOPE These Notes are guidelines
More informationGas plug-in hose, straight-through form. Instructions for Use. suitable for gas socket model G2019T, G2016T. G2023 from 01/1990.
Gas plug-in hose, straight-through form Instructions for Use suitable for gas socket model G2019T, G2016T Model Year built: G2023 from 01/1990 en_int Gas plug-in hose, straight-through form 2 from 12 Table
More informationLOAD-BEARING SHEETS SAFETY ANCHOR SA
www.ruukki.com LOAD-BEARING SHEETS SAFETY ANCHOR SA 113-153 INSTRUCTIONS FOR USE Contact Information Please see your local contact information from www.ruukki.com Figure 1. Cross-section of the safety
More informationISO INTERNATIONAL STANDARD. Personal protective equipment for protection against falls from a height Single-point anchor devices
INTERNATIONAL STANDARD ISO 14567 First edition 1999-03-01 Personal protective equipment for protection against falls from a height Single-point anchor devices Équipements individuels de protection contre
More informationISO INTERNATIONAL STANDARD. Hydraulic fluid power Filter elements Determination of resistance to flow fatigue using high viscosity fluid
INTERNATIONAL STANDARD ISO 23181 First edition 2007-08-15 Hydraulic fluid power Filter elements Determination of resistance to flow fatigue using high viscosity fluid Transmissions hydrauliques Éléments
More informationISO 4081 INTERNATIONAL STANDARD. Rubber hoses and tubing for cooling systems for internal-combustion engines Specification
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 4081 Third edition 2010-06-01 Rubber hoses and tubing for cooling systems for internal-combustion engines Specification Tubes et tuyaux en caoutchouc
More informationBRITISH STANDARD BS 341-4: Transportable gas container valves. Part 4: Pressure relief devices ICS
BRITISH STANDARD BS 341-4:2004 Transportable gas container valves Part 4: Pressure relief devices ICS 23.060.40 This British Standard, having been prepared under the direction of the Standards Policy and
More informationITF Court Surface Classification Scheme. ISSS Technical Meeting Nyon, October 2002
ITF Court Surface Classification Scheme ISSS Technical Meeting Introduction Introduction! No way to measure performance characteristics and, therefore:! For manufacturers to describe their products,! For
More informationDK46 - DK800 Supplementary instructions
DK46 - DK800 Supplementary instructions Variable area flowmeter Device category II2G with electrical internals Additional Ex manual KROHNE CONTENTS DK46 - DK800 1 Safety instructions 3 1.1 General... 3
More informationInternational Handball Federation. b) Goal Regulations
International Handball Federation b) Goal Regulations Edition: September 2007 Table of contents Page 1. General principles 3 2. Technical criteria for handball goals 3 3. Dimensions and diagrams of the
More informationTHE EXPERT IN LEVEL AND FLOW
LEVEL GAUGES WITH DIRECT LIQUID VISIBILITY Tubular/Reflex/Transparent types Series: ITA-GG / ITA-RG / ITA-TG Tubular Level Gauge Series ITA-GG Reflex Level Gauge Series ITA-RG Transparent Level Gauge Series
More informationNZQA registered unit standard version 1 Page 1 of 5. Meet requirements for Approved Filler Test Certificate for refrigerants
Page 1 of 5 Title Meet requirements for Approved Filler Test Certificate for refrigerants Level 3 Credits 3 Purpose This unit standard is for people working in the refrigeration and air conditioning industry
More informationSafety barriers surrounding a swimming pool area at 60A Goldflats Lane, Coatesville, Rodney
Determination 2010/014 Safety barriers surrounding a swimming pool area at 60A Goldflats Lane, Coatesville, Rodney 1. The matter to be determined 1.1 This is a Determination under Part 3 Subpart 1 of the
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 6004 Second edition 1991-08-15 Alpine skis - Ski binding screws - Requirements Skis alpins - Ws de fixation de skis - Spckifkations Reference number Foreword ISO (the International
More informationDR.ING. CARLO AVANZINI PROFESSIONAL ENGINEER GRIP TEST REPORT NOVA SIRIA, ROLETTO, Premise
GRIP TEST REPORT NOVA SIRIA, ROLETTO, 07.10.2013 1. Premise The present report covers the witnessing of the test conducted in the Nova Siria Factory in Roletto (Torino, Italy) to verify the behavior of
More informationGUIDELINES. Systems. Pressure. Guidelines Acceptance of equipment, establishment of safe operating limits and fitness for service
GUIDELINES Pressure Systems Guidelines Acceptance of equipment, establishment of safe operating limits and fitness for service Document Reference: PSG 16 Issue 04 Dated 13/09/16 The Safety Assessment Federation
More informationFall Arrest Anchor Solutions
Y O U L L N E V E R B E B E T T E R P R O T E C T E D Fall Arrest Anchor Solutions EACH TYPE TESTED AT THE NATIONAL ENGINEERING LABORATORY Roofanka and Ridganka CE approved to the PPE Directive COMPREHENSIVE
More informationfischer Epoxy Mortar FIS EB The basic epoxy mortar for applications in concrete
fischer Epoxy Mortar FIS EB The basic epoxy mortar for applications in concrete For standard applications in concrete and rebar connections. Advantages at a glance Epoxy mortar for applications in concrete
More informationPerformance Standards for Non-Turf Cricket Pitches Intended for Outdoor Use [TS6] ecb.co.uk
Performance Standards for Non-Turf Cricket Pitches Intended for Outdoor Use [TS6] ecb.co.uk 01 Introduction and Scope This Standard describes the requirements for non-turf cricket pitch systems intended
More informationISO INTERNATIONAL STANDARD. Cranes and lifting appliances Selection of wire ropes Part 1: General
INTERNATIONAL STANDARD ISO 4308-1 Third edition 2003-05-01 Cranes and lifting appliances Selection of wire ropes Part 1: General Grues et appareils de levage Choix des câbles Partie 1: Généralités Reference
More informationISO 6804 INTERNATIONAL STANDARD. Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers Specification
INTERNATIONAL STANDARD ISO 6804 Third edition 2009-09-15 Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers Specification Tuyaux et flexibles en caoutchouc et en plastique
More informationINDUSTRIAS IBAIONDO, HYDROPNEUMATIC TANKS
IBAIONDO, HYDROPNEUMATIC TANKS IBAIONDO, INTRODUCTION Hydropneumatic tanks are designed to be used in potable water supply installations as a part of the pressure booster set in order to ensure the adequate
More information1074 Kenran Industrial Dr. St. Louis, MO Phone: Taylortec WV-9A Work Vest
Taylortec WV-9A Work Vest WV-9A U.S.C.G. App# 160.03/9/0 Hammond, LA 70403 USA + 1 98 42 6266 Type V, inherently buoyant, 3 piece fabric covered foam work vest with pocket. 1 work vests per box. Polyethylene
More information1.8 INDUSTRIAL PROCESS WEIGHING IN HAZARDOUS AREAS
1.8 INDUSTRIAL PROCESS WEIGHING IN HAZARDOUS AREAS EXPLOSION PROTECTION In addition to the type approval and certification of industrial weighing systems concerned with accuracy, equipment that is also
More informationTest Report No Insulguard Fire Resistance Enclosure. Insulguard Australia Bentleigh, Victoria
Test Report No. 4548 Product: Insulguard Fire Resistance Enclosure Client: Insulguard Australia Bentleigh, Victoria Nature of tests: Limited testing to: AS/NZS 3000:2007 - Wiring rules AS/NZS 60695.11.5:2005
More informationBS EN ISO : 1999
Exova Warringtonfire Holmesfield Road Warrington WA1 2DS United Kingdom T : +44 (0 1925 655116 F : +44 (0) 1925 655419 E : warrington@exova.com W: www.exova.com BS EN ISO 4589-2: 1999 Determination of
More informationA summary of the update to standard EN 388 Protective Gloves Against Mechanical Risks
expert guide / A summary of the update to standard EN 388 Protective Gloves Against Mechanical Risks Published on 2nd November 2016 the revised standard: EN 388: 2016 Protective gloves against mechanical
More informationUIAA Standard (UIAA = Union Internationale des Associations d Alpinisme) January Mountaineering and Climbing Equipment. Connectors.
UIAA Standard (UIAA = Union Internationale des Associations d Alpinisme) January 2004 Mountaineering and Climbing Equipment Connectors UIAA 121 Foreword This UIAA Standard is only published in the English
More informationIntelligent Traffic Systems:
Printed on Cocoon Silk. Made with 100% FSC postconsumer waste. Cocoon Silk is 100% FSC recycled paper, process chlorine free. Please read and recycle Siemens Intelligent Traffic Systems Sopers Lane Poole
More informationBraemar Power Project Pty Ltd. B1 Pipeline. User Access Guide. Updated May 2018
Braemar Power Project Pty Ltd B1 Pipeline User Access Guide Updated May 2018 Alinta Energy Level 13, Grosvenor Place, 225 George Street, Sydney NSW 2000 User Access Guide 1. INTRODUCTION 1.1 Part 23 of
More informationAir Purge Unit. Series: LSP-compact Type: EJG 2-2. (Controlled with DigiFlow 515) Installation & Operation Manual 11/2014
Air Purge Unit Series: LSP-compact Type: EJG 2-2 (Controlled with DigiFlow 515) Installation & Operation Manual 11/2014 Headquarters Sales Office BENELUX Intra-Automation GmbH B. V. Intra-Automation HTP
More informationHOMOLOGATION PROCEDURES FOR MANUFACTURERS VOLLEYBALLS & BEACH VOLLEYBALLS
HOMOLOGATION PROCEDURES FOR MANUFACTURERS VOLLEYBALLS & BEACH VOLLEYBALLS FIVB World, Continental & National Volleyball and Beach Volleyball Competitions Edition 25 October 2016 FÉDÉRATION INTERNATIONALE
More informationDNVGL-CP-0187 Edition March 2016
CLASS PROGRAMME Type approval DNVGL-CP-0187 Edition March 2016 The electronic pdf version of this document, available free of charge from http://www.dnvgl.com, is the officially binding version. FOREWORD
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-26055-2 SOUTH AFRICAN NATIONAL STANDARD Transportable pressure receptacles for compressed, dissolved and liquefied gases Basic design, manufacture, use and maintenance Published by SABS
More informationDraft Indian Standard SAFES Part 2 Tests for Burglary Resistance (Fifth Revision)
Draft For Comments Only Draft Indian Standard SAFES Part 2 Tests for Burglary Resistance (Fifth Revision) Not to be reproduced without the permission of Last date for receipt of BIS or used as a STANDARD
More informationTaiwan Bicycle Industry Standard
Taiwan Bicycle Industry Standard TBIS 4210-9 First edition 2016.01.01 Cycles Safety requirements for bicycles Part 9: Saddles and seat post test methods Reference number: TBIS 4210-9:2015 (FDTS) Contents
More informationPressure switch KP-E. Data sheet
Data sheet Pressure switch KP-E KP-E pressure switches for use in refrigeration and air conditioning systems are equipped with SPDT gold plated contacts and stainless steel bellows. The high pressure switches
More informationCUT AND WEAR PROTECTION
CUT AND WEAR PROTECTION Selection of Products protection products need to be used in applications where sling damage can occur. Cutting of synthetic slings during use is the number one cause of sling accidents.
More informationISO 1977 INTERNATIONAL STANDARD. Conveyor chains, attachments and sprockets. Chaînes de manutention, plaques-attaches et roues dentées
INTERNATIONAL STANDARD ISO 1977 Second edition 2006-08-15 Conveyor chains, attachments and sprockets Chaînes de manutention, plaques-attaches et roues dentées Reference number ISO 1977:2006(E) ISO 2006
More informationSize : Ends : Min Temperature : Max Temperature : Materials : Cast iron body
Size : Ends : Min Temperature : Max Temperature : DN 40 to DN 300 Flanges R.F. PN10/16-10 C + 80 C Max Pressure : 16 Bars up to DN200 Specifications : Removable stainless steel filter Bolted bonnet with
More informationRequirements for the certification of movements and mechanical watches resistant to magnetic fields of 1.5 T ( G)
Institut fédéral de métrologie METAS METAS-N001/EN Requirements for the certification of movements and mechanical watches resistant to magnetic fields of 1.5 T (15 000 G) This document is a translation
More informationContact person Date Reference Page Michael Lindblad F025843A 1 (1) Sustainable Built Environment
issued by an Accredited Testing Laboratory Contact person Michael Lindblad 2016-02-03 5F025843A 1 (1) Sustainable Built Environment +46 10 516 58 58 Michael.Lindblad@sp.se Accred. No. 1002 Testing ISO/IEC
More informationGUMMIKOMPENSATOR GKF8000 / GKF8130
GUMMIKOMPENSATOR GKF8000 / GKF8 Size : Ends : Min Temperature : Max Temperature : DN 32 to 600 Flanges PN10/16-10 C + 100 C for EPDM and + 80 C for NBR Max Pressure : 16 Bars up to DN 300 Specifications
More informationReinforced Soil Retaining Walls-Design and Construction
Lecture 32 Reinforced Soil Retaining Walls-Design and Construction Prof. G L Sivakumar Babu Department of Civil Engineering Indian Institute of Science Bangalore 560012 Example calculation An 8 m high
More informationMaterials : Galvanized steel flanges
Size : Ends : Min Temperature : Max Temperature : DN 32 to 200 Flanges PN10/16-10 C + 80 C Max Pressure : 16 Bars Specifications : Absorb vibrations and noises Linear and angular compansion Single NBR
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 9073-16 First edition 2007-12-01 Textiles Test methods for nonwovens Part 16: Determination of resistance to penetration by water (hydrostatic pressure) Textiles Méthodes d'essai
More informationInternational Journal of Advanced Engineering Technology E-ISSN
Research Article PERFORMANCE OF ELEVATED WATER TANKS SUJECTED TO WIND FORCES Dr. Hirde Suchita K. 1, ajare Asmita A. 2, Hedaoo Manoj N. 3 Address for Correspondence 1 Professor in Applied Mechanics, Govt.
More informationEvidence of Performance. Class 4. Class 5A. Class C5 / B5. Test Report No PR01. ift Rosenheim
Evidence of Performance Test Report No 16-002359-PR01 (PB-A01-02-en-01) Client Product Designation Performance-relevant product details Overall dimensions (W x H) Special features - / - SUNCE Marinkovic
More informationAustralian/New Zealand Standard
AS/NZS 2210.3:2009 AS/NZS 2210.3:2009 Australian/New Zealand Standard Occupational protective footwear Part 3: Specification for safety footwear (ISO 20345:2004, MOD) AS/NZS 2210.3:2009 This Joint Australian/New
More informationIRB Regulation 22 Performance Specification Re-test Field Report
IRB Regulation 22 Performance Specification Re-test Field Report 1. Site Details Site Name: The Connaught School Site Address: Tongham Road, Aldershot, GU12 4AS Site Contact: Martin Sterio Site E-mail:
More informationTECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION IEC TS 61245 Edition 2.0 2015-03 Artificial pollution tests on high-voltage ceramic and glass insulators to be used on d.c. systems INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS
More informationCATS Deliverable 4.2: CATS propulsion system requirements
Integrated Vehicle Safety Automotive Campus 30 5708 JZ Helmond P.O. Box 756 5700 AT Helmond The Netherlands TNO 2016 R10926 CATS Deliverable 4.2: CATS propulsion system requirements www.tno.nl T +31 88
More informationPTB Ex PT Scheme. Procedure Instruction of program Explosion Pressure - Test Round 2017
Procedure Instruction of program Explosion Pressure - Test Round 2017 Content 1 General Performance... 2 2 Measurand / Characteristic of interest... 2 3 Test Item and Configurations... 2 3.1 Components...
More informationGuidance on the Legal Obligations for Importers, Retailers and Distributors of Category 1 Fireworks
Guidance on the Legal Obligations for Importers, Retailers and Distributors of Category 1 Fireworks Issued by the Office of the Government Inspector of Explosives GD 8/2010 First Issued July 2010 Status:
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12385-6:2004 Steel wire ropes - Safety - Part 6: Stranded ropes for mine shafts Steel wire ropes - Safety - Part 6: Stranded ropes for mine shafts EESTI STANDARDIKESKUS EESTI STANDARDI
More informationFebruary 5, 2014 REQUEST FOR ADDITIONAL INFORMATION FOR THE REVIEW OF THE MODEL NO PACKAGE
February 5, 2014 Mr. Patrick W. McGuire, Assistant Manager Nuclear Material Stabilization Project Savannah River Operations Office U.S. Department of Energy P.O. Box A Aiken, SC 29802 SUBJECT: REQUEST
More informationISO INTERNATIONAL STANDARD. Continuously hot-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and sheet/plate
INTERNATIONAL STANDARD ISO 9444-2 First edition 2009-06-01 Continuously hot-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and sheet/plate Acier inoxydable laminé à chaud en
More informationDISSOLUTION TEST FOR SOLID DOSAGE FORMS
Seite 1 von 15 01/2010:20903 corrected 6.8 2.9.3. DISSOLUTION TEST FOR SOLID DOSAGE FORMS This test is provided to determine compliance with the dissolution requirements for solid dosage forms administered
More informationAutomatic Control Unit. Controlmatic E.2. Type Series Booklet
Automatic Control Unit Controlmatic E.2 Type Series Booklet Legal information/copyright Type Series Booklet Controlmatic E.2 All rights reserved. The contents provided herein must neither be distributed,
More informationpdf WATER RETICULATION STANDARD VENTILATION LOUVRE BOXES SINGLE AND DOUBLE DUCT SYSTEMS
Drawing Index Name Doc.No Document Description 2001979.061H.pdf 2001979.061 WATER RETICULATION STANDARD SCOUR VALVE CHAMBER WITH CIRCULAR COVER AND FRAME SHEET NO1 OF 2 2001979.062F.pdf 2001979.062 WATER
More informationDECLARATION OF PERFORMANCE
ROCKWOOL B.V. / ROCKPANEL Group Konstruktieweg 2 NL-6045 JD Roermond, Netherlands www.rockpanel.com DECLARATION OF PERFORMANCE No. 0764-CPR-0276 DK english - vs01 1. Unique identification code of the product-type:
More informationFALL PROTECTION
115500 FALL PROTECTION PART 1 GENERAL 1.01 General A. Cornell University seeks to prevent exposures to fall hazards whenever possible and protect personnel that may be exposed to fall hazards. Therefore,
More informationProduct Identification
Product Identification All SCAFCO products have a four part identification code which identifies the size (both depth and flange width), style, and material thickness of each member. Example: Member Depth:
More informationSwimming pool barriers. Schedule 1 - Modifications to the Standard... 5 MP 3.4 SWIMMING POOL BARRIERS. Table of Contents
Table of Contents Purpose... 2 Commencement... 2 Application... 2 Referral Agency... 2 Compliance with the QDC... 2 Relationship between the Standard and this part... 2 Associated Requirements... 2 Referenced
More informationMountaineering and Climbing Equipment. CRASH PADS Determination of the critical fall height. Foreword
Mountaineering and Climbing Equipment CRASH PADS Determination of the critical fall height UIAA 161 Foreword This UIAA Standard is only published in the English language version, which is the master text.
More informationRobustness of Steel Joints in Fire: Temperature Development and Structural Fire Behaviour
Robustness of Steel Joints in Fire: Temperature Development and Structural Fire Behaviour Y C Wang, C G Bailey and X H Dai School of Mechanical, Aerospace and Civil Engineering The University of Manchester,
More informationCE conform applications according to EN Windows without thermal break Systems Forster presto and Forster norm
CE conform applications according to EN 14351-1 Windows without thermal break Systems Forster presto and Forster norm 2 Properties Table 1 Window Operating forces Resistance to wind load Air permeability
More informationTECHNICAL MANUAL. DHR70N Polar. Den Haan Rotterdam
TECHNICAL MANUAL DHR70N Polar SINCE 1922 Den Haan Rotterdam WARNING! - Turn power off before inspection, installation or removal - Keep combustible materials away from lamp - Allow lamp/fixture to cool
More information