A A A

Transcription

1 Winchester SXP Talon T Rear Pistol Grip with Scorpion Recoil Grip A A A Extended Scorpion Material to Reduce and Discomfort to the Shooter's Hand and Thumb Sure-Grip Texture Triton Mount System

2 Winchester SXP Talon T Rear Pistol Grip [] M8 x.5 x 5mm Flat Head Socket Cap Screw [] 6- x /" Torx Screw [] 6- x /" Allen Head Screw [] #6 Washer Phillips Head Screwdriver Torx Set Wrench Set Allen Set! Warning: When handling a firearm, always follow the proper handling procedures at all times. Failure to follow these procedures could result in serious damage, injury, or death. ATI is not responsible for damage to property, injury, or death resulting from improper installation, misuse or modification of products. If you are not comfortable completing any of the following steps, or do not have the proper tools enlist the help of your local gunsmith. ATI is not responsible for components that are damaged due to improper installation. A Stock Removal! Point the shotgun in a safe direction and place the saftey in the "on" position. Next pull back, and carefully inspect the chamber to be sure the shotgun is unloaded. "Will Not fit Shotguns with.5" Ejection Ports" Remove the existing recoil pad from your stock by unscrewing the two phillips head screws in the rear of the pad as seen in Figure A. Next use a 6mm allen wrench to remove the stock bolt from the inside of the opening in the rear of the stock as seen in Figure B. A B B Triton Mount Installation Place the Triton Receiver Side Mount onto the shotgun receiver as seen in Figure. Using the M8 x.5 x 5mm flat head mounting bolt supplied for your shotgun, tighten the triton mount to the receiver with a 5mm wrench as seen in Figure

3 Winchester SXP Talon T Rear Pistol Grip C Trigger Pad Installation Remove the yellow side of the double sided adhesive strip as seen in Figure. Place the adhesive strip (with the adhesive side down) onto the pistol grip as shown in Figure. Remove the white strip by pulling up, leaving the adhesive on the vertical portion of the pistol grip channel as seen in Figure

4 Winchester SXP Talon T Rear Pistol Grip C Trigger Pad Installation -Continued Attach the foam padding to the adhesive strip with the thicker part of the foam pad in the vertical portion of the pistol grip channel as seen in Figure. D Pistol Grip Spacer To replace the blank spacer with the sling loop spacer, remove the phillips head screw from the bottom of the grip as seen in Figure A. Next slide the scorpion grip pad off of the rear pistol grip housing as seen in Figure B. A B Next, remove the /-0 x /" bolt and /-0 nut by using a 5/" allen wrench and a 7/6" open face wrench as seen in Figure. Select either the sling loop spacer or blank spacer and place into the Triton Mount as seen in Figure. Blank Spacer Loop Spacer Insert Spacer

5 Winchester SXP Talon T Rear Pistol Grip D Pistol Grip Spacer Installation -Continued Re-install the Triton Mount onto the pistol grip and then secure the mount to the pistol grip using the /-0 x /" bolt and /-0 Hex nut that were removed in step as seen in Figure. E Pistol Grip Installation Tighten the /-0 x /" bolt and the /-0 hex nut by using a 5/" allen wrench and a 7/6" open face wrench as seen in Figure. Next, re-install the Scorpion Grip Pad by the sliding the Scorpion Grip Pad back onto the pistol grip housing as seen in Figure A and tightening the phillips head screw at the bottom of the pistol grip as seen in Figure B. A B

6 Winchester SXP Talon T Rear Pistol Grip E Pistol Grip Installation -Continued Slide the stock side Triton Mount into the receiver side Triton Mount as seen in Figure A. Using the supplied 6- x /" Torx screw and #6 lock washer, tighten with a T5 Torx screwdriver as seen in Figure B. If the lock washer is not used the screw may back out of the mount and could cause the triton mount to disengage. A B Note: Before completely tightening the Triton Mount with the supplied torx or allen screw, make sure the Triton Mount is aligned correctly. The Mount should be completely flush, and the dovetail locking system should easily slide together. DO NOT tighten the Triton Mount with the dovetail system aligned incorrectly. This may damage the Triton Mount or stock, and is NOT covered under the manufacturer's warranty. INCORRECT Note: Once you have aligned the Triton Mount correctly and fastened the supplied torx or allen screw, you may notice a small gap on either side of the Triton Mount. Do not try to close this gap. It is engineered to insure the Triton Dovetail Mount binds together to accept the full recoil of the shotgun. The supplied torx or allen screw simply prevents the two pieces from sliding apart. Over tightening may strip the threads, and in some extreme cases may cause the screw head to shear off, which is NOT covered under the manufacturer's warranty. CORRECT NOTE: Tighten until snug, then tighten / turn more. Over tightening may strip the threads and in extreme cases cause the screw head to shear off, which is NOT covered under the manufacturer's warranty. Over torquing of the screw can cause bending in the mount. If you encounter this bending the mount has been damaged and may not be used. As a precaution, after each use please be sure to check the engagement of the mount