Tidland Series 'C' Knifeholder INSTALLATION MANUAL Swing Cartridge Class II, III Shear Slitting
|
|
- Alicia Carter
- 6 years ago
- Views:
Transcription
1 Tidland Series 'C' Knifeholder INSTALLATION MANUAL Swing Cartridge Class II, III Shear Slitting Please read and understand all the instructions before you start to install the Tidland Series 'C' Knifeholder. For information, contact: Tidland Corporation P.O. Box 1008 Camas, WA PART NUMBER of 3 sections of Part Number
2 Table of Contents Knifeholder Safety.2 Receiving and Unpacking 2 Knifeholder Components..3 Installation Procedures.3 A. Determine Web Path Direction of Web 4 2. Type of Slitting..4 B. Prepare to Mount Guidebar 5 1. Determine Space Requirements 5 2. Determine Setback Distance (Tangent Shear Slitting only) Determine Mounting Dimensions...7 a. Vertical Mounting Dimension...7 b. Horizontal Mounting Dimension..7 C. Mount Guidebar 8 D. Mount Knifeholder to Guidebar..9 E. Install Pneumatic System..10 2
3 Knifeholder Safety IMPORTANT! Read and understand all instructions before operating the knifeholder. Failure to follow instructions may cause the knifeholder to function incorrectly and cause serious injury. The Tidland Series 'C' Knifeholder is intended to be used to produce a slit when used with a driven anvil system, and there is no other intended purpose. While operating the knifeholder, follow all existing plant safety instructions and/or requirements. Always wear stainless steel protective gloves when changing or removing the knife blade. Keep fingers clear of the blade edge at all times.! WARNING Sharp knives may cause severe bodily injury. Keep clear. Do not put hands in machines. Keep hands away from knife blades at all times. Compliance with Federal, State, and local safety regulations is your responsibility. Be familiar with them and always work safely. Receiving and Unpacking Handle and unpack the equipment carefully. Upon arrival, check the shipment against the packing list. Any damage should be reported to the carrier at once. Equipment that will not be installed immediately should be stored in a clean, dry location. Be careful to prevent moisture, dust, and dirt from accumulating in storage and installation areas. 3
4 Knifeholder Components Tidland Series 'C' Knifeholder Manual Position Lock 2. Locking Gib 3. Auto-Lock Brake Shoe 4. Dovetail Mount 5. Pinion Gear 6. Rod Guide Bushing 7. Cant Angle Key 8. Strut 9. Blade Lock 10. Knife Blade 11. Blade Guard 12. Set Stop Pin 13. Latch Pin 14. Socket Head Cap Screw 15. Wedge Lock Screw 16. Traverse Knob 17. Main Body 18. Valve Body 19. Gib Mounting Screws 20. Function Control Knob 21. Hose Barb Fitting 22. Depth Adjustment Knob 23. Depth Adjustment Lock Nut Specifications Class II Class III Blade Diameter 5.91" (150mm) 7.87" (200mm) Minimum Slit 2" (50.80mm) 3" (76.20mm) Typical Maximum Speed* 5,500 fpm (1,676 mpm) 10,000 fpm (3048 mpm) Recommended Plant Air Minimum 90 psi (6.2 bar) Minimum 90 psi (6.2 bar) Recommended Operating Air psi ( bar) psi ( bar) *Note: Actual speed is dependent on application and material 4
5 A. Determine Web Path 1. Direction of Web: A B 2. Type of Slitting: 1/2 of wrap angle 90 Tangent Knifeholder axis should be 90 to web path. OR Wrap Knifeholder axis should bisect the wrap angle. 5
6 3. Select Contact Side: L Left side R Right side 4. Select Cant Angle Key: Web Path Contact Side A L R A R L B L L B R R Key Required See 'Changing the Cant Angle Key' in the Maintenance Manual. 6
7 B. Prepare to Mount Guidebar 1. Determine Space Requirements Tidland Series 'C' Knifeholder Geometry * *Note: Reserve 1/2 of the total stroke for blade regrinding Inches A B C D E F G H I J K L M N O P Q R Class II Class III Millimeters A B C D E F G H I J K L M N O P Q R Class II Class III Note: Dimensions are nominal and represent the average of assembled units. These are not the specifications of individual parts nor do they reflect manufacturing tolerances. 7
8 2. Determine Setback Distance (for Tangent Shear Slitting only) "A" Web Path Setback Typical Setback for Paper Based Products*: Class II: Class III: 1/4" (6.35mm) 3/8" (9.53mm) "B" Web Path * Other products may require different setbacks. Setback 8
9 3. Determine Mounting Dimensions (Horizontal Mounting Dimension) Support beam Centerline of guidebar mounting holes (Vertical Mounting Dimension) Anvil blade Parallel to web & tangent to anvil blade a. Vertical Mounting Dimension (VMD) Tangent and Wrap Slitting Class II 10-3/16" mm Class III 12-3/16" mm These dimensions reserve approximately 1/2 of knifeholder stroke for blade regrinding. b. Horizontal Mounting Dimension (HMD) Tangent Shear Slitting "A" Web Path "B" Web Path Class II 3-7/32" 81.76mm 2-23/32" 69.06mm Class III 3-27/32" 97.63mm 3-3/32" 78.58mm These dimensions will result in setbacks as listed in 'Determine Setback Distance'. Wrap Shear & Crush Slitting "A" and "B" Web Paths Class II 2-31/32" 75.40mm Class III 3-15/32" 88.10mm These dimensions provide no setback. 9
10 C. Mount Guidebar 1. Mark the mounting bolt center line on the support beam. 2. The guidebar must be straight within 0.010" (0.25mm) on a rigid and vibration free support. B A Guidebar Free Space Note: The guidebar mounting bolt holes are pre-drilled. A is 12" (304.80mm). 3. Measure the center to center distances between the mounting bolt holes (A) on the guidebar and the overall length of the guidebar (B). Leave enough free space on each end of the support beam for knifeholder removal. Class II Class III Minimum Space Recommended for Removal (Free Space) 3" (76.20mm) 4" (101.60mm) 4. Transfer the dimension (A) on the marked centerline on the support beam. 5. Center punch the mounting bolt pattern on the marked line. 6. Drill and tap the support beam for the mounting bolts. 7. Clamp the guidebar in place on the support beam. 8. Work from one end to the other installing the bolts until the guidebar is securely fastened to the support beam. Make sure that the guidebar is aligned (parallel) with the driven anvil. 10
11 D. Mount Knifeholder to Guidebar Manual Position Lock Knob Gib Adjustment Set Screws (2) Locking Gib Mounting Screws (2) Traverse Knob Locking Gib Auto-Lock Brake Shoe Guidebar Pinion Gear Guidebar Dovetail Mount Traverse Set Screw (1) 1. Turn the manual position lock knob counterclockwise to fully retract. 2. Make sure that the auto-lock brake shoe is fully retracted into the locking gib. 3. Align the dovetail mount and pinion gear to the guidebar and gear rack. 4. Slide the knifeholder onto the guidebar from one end. 5. Turn the traverse knob to make sure that the knifeholder moves freely on the guidebar. 6. Adjust the pinion gear clearance using the traverse setscrew. Keep in mind that the gib brake will "pull" the pinion gear into the gear rack, so leave enough clearance. 7. Tighten the manual position lock knob to secure the knifeholder in position. Note: Where end installation is not possible by sliding the knifeholder onto the guidebar, the knifeholder can be mounted by removing the locking gib. a. Remove locking gib mounting screws located on the front of the control body. b. Remove locking gib. c. Place knifeholder on guidebar. d. Reinstall the locking gib without altering the setscrew setting. e. Hold the knifeholder firmly against the locking gib while alternately tightening the locking gib mounting screws. Note: If the knifeholder does not move freely on the guidebar, refer to step 1. Impact to the knifeholder body should never be used to move the knifeholder. 11
12 E. Install Pneumatic System Tidland Corporation recommends the use of a pneumatic system to prevent airborne oil or water from contaminating the knifeholders. This system (Part Number: ) includes: A. 3/8" (9.52mm) supply air lines B. 5 micron air filter/pressure regulator with gauge (0-100 psi or bar) C. Coalescing filter D. 3-way manual valve with muffler E. Quick exhaust valve with muffler A quick disconnect fitting* B C D E air manifold* *The air manifold and quick disconnect fittings are also available from Tidland. Recommended operating air pressure: psi ( bar). This is a guideline for knifeholder setup; the actual air pressure is dependent upon application and material. Clean, non-lubricated, dry air is required for optimum performance of the Series 'C' Knifeholder. Before operating the knifeholder, make sure that the air lines from the air manifold to the blade cartridge are securely connected. 12
13 COMPANIES OF In the United States In the United Kingdom In Germany Tidland products are Tidland Corporation Tidland (UK) Ltd. Tidland GmbH also manufactured in: P.O. Box , Manchester Road Siemensstrasse Keene, NH U.S.A. Camas, WA Denton, Manchester D Ahaus Sao Paulo, Brazil FIFE CORPORATION U.S.A. UK M34 3PR Germany Sydney, Australia MAGNETIC POWER SYSTEMS, INC. Phone: Phone: Telefon: Tokyo, Japan TALIS INTERNATIONAL,LLC Fax: Fax: Mumbai, India TIDLAND CORPORATION Fax: Web Site: Tidland Corporation Rights reserved to amend technical details without notice of November
Tidland Series 'C' Knifeholder INSTALLATION MANUAL Rigid Cartridge Class I, II, III Shear Slitting
Tidland Series 'C' Knifeholder INSTALLATION MANUAL Rigid Cartridge Class I, II, III Shear Slitting Please read and understand all the instructions before you install the Tidland Series 'C' Knifeholder.
More informationTidland Performance Series Manual Knifeholder
TIDLAND SLITTING SOLUTIONS Tidland Performance Series Manual Knifeholder User Manual EN Class I, II and III MI 557416 1 L IMPORTANT! KNIFEHOLDER SAFETY When using knifeholders, basic safety precautions
More informationTidland e-knifeholder
TIDLAND SLITTING SOLUTIONS Tidland e-knifeholder Installation, Operation and Maintenance Class II Class III EN Class II and III MI 686810 1 Q CONTENTS Contact Information... 4 Receiving and Unpacking...
More informationControl Series Electronic Knifeholder
TIDLAND SLITTING SOLUTIONS Control Series Electronic Knifeholder Installation and Maintenance EN MI 270015467 1 A Class II and II For use with the Control Series Touchscreen User Manual 270015468 Optional
More information30T A/Manual Hydraulic Shop Press
30T A/Manual Hydraulic Shop Press Operation Manual 1 1. Important Information 1.1 Safety Information 1.1.1 Hazard Symbols Used in the Manuals This manual includes the hazard symbols defined below when
More informationSETTING UP THE MODEL 210B SRA
SETTING UP THE MODEL 210B SRA SAFETY PRECAUTIONS FOR THE MODEL 210B SRA System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris: During
More informationCopyright MAY, 2008 By Grizzly Industrial, Inc. Warning: No portion of this manual may be reproduced in any shape or form without the written
MODEL G5789/G5790 13-PIECE 3 4" IMPACT WRENCH KIT INSTRUCTION MANUAL Copyright MAY, 2008 By Grizzly Industrial, Inc. Warning: No portion of this manual may be reproduced in any shape or form without the
More informationaccidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS
18 GAUGE 2 INCH BRAD NAILER Model: 7555 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.
More informationaccidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS
18 GAUGE 1-1/4 INCH BRAD NAILER Model: 7611 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.
More informationIMPORTANT: RECEIVING INSTRUCTIONS:
Instruction Sheet Sidewinder Mechanical Bender IMPORTANT: RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any shipping damage is found, notify carrier at once.shipping damage
More informationHEAVY-DUTY AIR RATCHET WRENCH OWNER S MANUAL
HEAVY-DUTY AIR RATCHET WRENCH OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in
More informationAllspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW. Tel +44 (0)
Allspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW Tel +44 (0)1254 615100 www.allspeeds.co.uk SOFT LINE CUTTER SL55 PRODUCT CODE No. 980504 INSTRUCTIONS FOR INSTALLATION,
More informationJARVIS. Model CPE Hock and Neck Cutter EQUIPMENT... TABLE OF
74 Hock and Neck Cutter EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page with Control Circuit. 4304003 only... 4304004 Balancer... 1350084 Control Circuit... 3350010 Air Hose (Yellow)... 3323003
More informationCLAY DIGGER. Safety, Operating, Maintenance Instructions & Spare Parts List MCD-30A 1" MCD-30A 7/8"
CLAY DIGGER Safety, Operating, Maintenance Instructions & Spare Parts List MCD-30A 1" MCD-30A 7/8" Read and understand this manual and all other safety instructions before using the equipment. CONTENTS
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More information35 TON HYDRAULIC PUNCH WARNING
OPERATORS GUIDE REL-35T-PNC 35 TON HYDRAULIC PUNCH NOTICE Sizes, weights and tool specifications listed in this manual are subject to change without notice. Please consult factory for information and updates.
More informationCopyright MAY, 2008 By Grizzly Industrial, Inc. Warning: No portion of this manual may be reproduced in any shape or form without the written
MODEL G5791/G5792 17-PIECE 1 2" IMPACT WRENCH & RATCHET KIT INSTRUCTION MANUAL Copyright MAY, 2008 By Grizzly Industrial, Inc. Warning: No portion of this manual may be reproduced in any shape or form
More information1 DRIVE INDUSTRIAL IMPACT WRENCH
1 DRIVE INDUSTRIAL IMPACT WRENCH 92622 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2004 by Harbor Freight
More informationATD /8 x 50 Retractable Air Hose Reel Owner s Manual
ATD-31166 3/8 x 50 Retractable Air Hose Reel Owner s Manual Features Heavy-gauge, all-steel reel assembly 8-position ratchet mechanism locks reel at desired hose length 5-position adjustable roller outlet
More information3/8" Dr. Air Butterfly Impact Wrench
8192106 3/8" Dr. Air Butterfly Impact Wrench Owner s Manual Read and understand all instructions before use. Retain this manual for future reference. Specifications Construction: Polished aluminum and
More informationHANDBOOK. Squeeze Off Unit SOU 400. Please refer any queries to:
HANDBOOK Squeeze Off Unit SOU 400 Please refer any queries to: Hy Ram Engineering Co Ltd Pelham Street Mansfield Nottinghamshire NG18 2EY Telephone No: (01623) 422982 Please note all queries should state
More information2K 600mL Dispense Guns with Built-In Retainers
2K 600mL Dispense Guns with Built-In Retainers Operating Manual Electronic pdf files of Nordson EFD manuals are also available at www.nordsonefd.com You have selected a reliable, high-quality dispensing
More informationMODEL 200 KNIFE GATE VALVES INSTALLATION & MAINTENANCE MANUAL
MODEL 200 KNIFE GATE VALVES INSTALLATION & MAINTENANCE MANUAL Index 1. List of components / General arrangement 2. Description 3. Handling 4. Installation 5. Actuators / Operation 6. Maintenance a. Changing
More informationAIR INLINE METAL SHEAR
AIR INLINE METAL SHEAR ASSEMBLY and OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd. / Camarillo, CA 93011 Copyright 1997 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork
More informationTidland Air Chuck Installation, Operation and Maintenance
TIDLAND WINDING SOLUTIONS Tidland Air Chuck Installation, Operation and Maintenance EN MI 517786 1 L www.maxcessintl.com Tidland Air Chuck MI 517786 1 L Page 2 CONTENTS Assembly Diagram and Parts List...
More information310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment
OPERATOR S MANUAL FOR MORSE TILT-TO-LOAD DRUM ROTATOR SAFETY INFORMATION: While Morse Manufacturing Co. drum handling equipment is engineered for safety and efficiency, a high degree of responsibility
More informationSide-of-Pole Mount for 1 Module (SPM1) For Module Types A & B
Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 080311-2 SP3363-1 Side-of-Pole Mount for 1 Module (SPM1)
More informationSIGNATURE DEF REELS Models: Bare Reel Reel Reel Reel
SERVICE BULLETIN SB2023 Rev C 7/11 SIGNATURE DEF REELS Models: 2400-006 Bare Reel 2400-007 16 Reel 2400-008 20 Reel 2400-009 30 Reel Thoroughly read and understand this manual before installing, operating
More informationBray/ VAAS O-Ported Series Knife Gate Valve 770/780 Series Operation and Maintenance Manual
Bray/ VAAS Knife Gate Valve 770/780 Series Operations and Maintenance Manual Table of Contents Definition of Terms 1 Safety Instructions 1 Introduction 2 Unpacking 2 Storage 2 Installation 2 Commissioning
More information4 ANGLE GRINDER MODEL NO: CAT 52 PART
4 ANGLE GRINDER 4 ANGLE GRINDER MODEL NO: CAT 52 PART No: 3110685 OPERATION & MAINTENANCE INSTRUCTIONS 0807 Fig.1 SPECIFICATIONS Model:...CAG52 Part Number:...3110685 Rated Wheel...Capacity: 4 x 1/4 (type
More informationAllspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW. Tel +44 (0)
Allspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW Tel +44 (0)1254 615100 www.allspeeds.co.uk SOFTLINE CUTTER SL80 PRODUCT CODE No. 980248 INSTRUCTIONS FOR INSTALLATION,
More informationInstruction Sheet. CP2000: 2000 lb Cable Puller IMPORTANT RECEIVING INSTRUCTIONS SAFETY ISSUES
Instruction Sheet CP2000: 2000 lb Cable Puller RPS-0148 07/02 IMPORTANT RECEIVING INSTRUCTIONS Visually inspect all components for shipping damage. If shipping damage is found, notify carrier at once.
More informationOPERATION MANUAL Please read this Operation Manual carefully before use, and file for future reference.
English Lubrication Free Air Turbine Handpiece with Water Spray OPERATION MANUAL Please read this Operation Manual carefully before use, and file for future reference. OM-T0286E 001 Thank you for purchasing
More informationRARS5000 AIR BODY SAW OWNER S OPERATING MANUAL
RARS5000 AIR BODY SAW OWNER S OPERATING MANUAL DESCRIPTION 1. No mar 2. No mar tip 3. Housing grip 4. Trigger 5. Air inlet 6. Air inlet plug 7. Plastic board Important! It is essential that you read the
More information3/8 ANGLED AIR DRILL
3/8 ANGLED AIR DRILL MODEL NO: CAT61 PART NO: 3110461 OPERATING & MAINTENANCE INSTRUCTIONS GC0614 INTRODUCTION Thank you for purchasing this CLARKE Angled Air Drill. Before attempting to use this product,
More informationSPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1.
2 GALLON TWIN STACK AIR COMPRESSOR Model: 9526 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or
More informationLUBRICATOR ASSEMBLY AND OPERATING INSTRUCTIONS
AIR FILTER, REGULATOR AND LUBRICATOR 4035 ASSEMBLY AND OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 004 by Harbor Freight
More informationO P E R ATING INSTRUCTIONS FOR MODEL SPR-45 Automatic Screen and Stencil Printer
O P E R ATING INSTRUCTIONS FOR MODEL SPR-45 Automatic Screen and Stencil Printer TABLE OF CONTENTS I. SPECIFICATIONS...3. II. SAFETY INSTRUCTIONS...4. III. INSTALLATION...5. IV. SET-UP...6. V. SYSTEM OPERATION...9.
More informationGRAVITY BIKE RACK ASSEMBLY & OPERATING INSTRUCTIONS
GRAVITY BIKE RACK 94479 ASSEMBLY & OPERATING INSTRUCTIONS Due to continuing improvement, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011
More informationSide-of-Pole Mount for 1 Module (SPM1) For Module Type C
Module Type Width Length C 22-27 56-63 Side-of-Pole Mount for 1 Module (SPM1) For Module Type C ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 022212-1 Side-of-Pole Mount
More informationCLEATBENDER FOR ALL 1836 MODELS OPERATION & MAINTENANCE MANUAL
CLEATBENDER FOR ALL 1836 MODELS OPERATION & MAINTENANCE MANUAL Manual# LM1836 October 2006 Copyright by Lion Machinery A member of the Formtek Group All Rights Reserved The information in this document
More informationSAILTEC, INC CONGER COURT, OSHKOSH, WI USA
OK to make this valve hand tight. Pin Mount Style Integral lies 4-5 Degrees above Horizontal. If you store your Hunter "bow down" you will get air-lock in the Integral. Slot Mount Style Pump Body "Down"
More informationATV 90 Y-12 YOUTH 2-STROKE RED (A2004ATB2BUSR) Page 1 of 52 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY
2004 ATV 90 Y-12 YOUTH 2-STROKE RED (A2004ATB2BUSR) Page 1 of 52 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY 2004 ATV 90 Y-12 YOUTH 2-STROKE RED (A2004ATB2BUSR) Page 2 of 52 A-ARM, FLOOR PANEL, AND BUMPER
More informationPUN M Manual Finger Punch Safety and Operation Manual
PUN M Manual Finger Punch 300-600 - 900 Safety and Operation Manual For punching thermoplastic belting materials only. WARNING IMPROPER OR UNSAFE use of this tool can result in serious bodily injury! This
More informationTidland G690 Leaf Shaft
TIDLAND WINDING SOLUTIONS Tidland G690 Leaf Shaft Operation and Maintenance EN 3" Shaft Diameter MI 746510 1 C CONTENTS INTRODUCTION 1-1 About these operating instructions... 1-1 Product overview... 1-2
More informationINSTRUCTION MANUAL MST AFTERCOOLER SYSTEM MODEL
INSTRUCTION MANUAL MST AFTERCOOLER SYSTEM MODEL 8059601 To be used with MST Model 8050501 Ambient Air Pump 7/12/05 2 TABLE OF CONTENTS GENERAL INFORMATION... 3 WARNING...4,5 UNPACKING AND AFTERCOOLER ASSEMBLY
More informationDiscontinued. Powers Controls. Technical Instructions Document No P25 RV Rev. 1, May, RV 201 Pressure Reducing Valves.
Powers Controls RV 201 Pressure Reducing Valves Description Features Product Numbers Dual Pressure PRV Technical Instructions Document No. 155-049P25 RV 201-1 Single Pressure PRV The RV 201 Pressure Reducing
More informationHose Reel Enclosure Retrofit Kit
Instructions Hose Reel Enclosure Retrofit Kit 332143A EN Retrofits the Series 500 Hose Reel Enclosure for use with a XD20 Series Hose Reel. For professional use only. Kit No. 24P914 Important Safety Instructions
More informationRapidmain Installation Guide
Rapidmain Installation Guide Aluminium Compressed Air Pipe Work Installation Guide Trafalgar Court, Waterloo Ind Estate, Widnes Cheshire. UK. Ref: Rapidmain installation guide 4b Index 1. Rapidmain fittings:
More informationMODEL H8253 AIR BELT SANDER INSTRUCTION MANUAL
MODEL H8253 AIR BELT SANDER INSTRUCTION MANUAL COPYRIGHT DECEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL
More informationPneumatic Controls, Air Settings, Hydraulic adjustments on; Models 22HF, 16HF & 1600 machines
Knowledge Base Article Type: Instructions Pneumatic Controls, Air Settings, Hydraulic adjustments on; Models 22HF, 16HF & 1600 machines Description: Instruction sheet on how to make proper pneumatic air
More information2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL
2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL Model: 52024 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement,
More information250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO
250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual
More informationMUELLER. A Wall Type. Indicator Post. Reliable Connections. General Information 2. Technical Data/ Dimensions 3. Installation 4-5.
Installation Instructions manual MUELLER table of contents PAGE A-20814 Wall Type General Information 2 Technical Data/ Dimensions Installation 4-5 Maintenance 6 Parts 7 Indicator Post! WARNING: 1. Read
More informationTroyer s Gourd Rack 8 unit F R H O P
B E A D I M-N L Vertical Parts F R H O P Horizontal Parts C G J Updated 11/16 Parts List A: Top of Pole B: Bottom of Pole C: 48 Ground Stake D: Top Perch rods 48 long E: Hub F: Rope Winder w/ attached
More informationX-6 STRINGING MACHINE OWNER'S MANUAL. Issue 1 - May Copyright 2004 GAMMA Sports - All Rights Reserved
X-6 STRINGING MACHINE OWNER'S MANUAL Issue 1 - May 2004 Copyright 2004 GAMMA Sports - All Rights Reserved OWNER'S MANUAL GAMMA X-6 TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3...ASSEMBLY
More information250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO
250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual
More information1. CONDITIONS FOR USE 2. SAFETY
1. CONDITIONS FOR USE This micro abrasive blaster may only be operated: Indoors; Below 6500 ft above sea level altitude; Ambient air temperature between 40-105 F (5-40 C); Maximum relative humidity of
More informationTube-Line Accelerator Spinner Kit
Tube-Line Accelerator Spinner Kit Operator's Manual PP-00799 (19/09/11) 2 TO THE OWNER This manual contains information concerning the adjustment, assembly and maintenance of your Tube-Line Spinner Kit.
More informationFinal Assembly Instructions Bikes with Quill Stems
Final Assembly Instructions Bikes with Quill Stems Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert
More informationSanta Fe Cycles Assembly Guide Introduction
Santa Fe Cycles Assembly Guide Introduction Congratulations on your purchase of your new Santa Fe bicycle. You have purchased a bicycle that has many features and qualities. Please take a few minutes and
More informationHPB25 Hydraulic Paving Breaker
INSTRUCTION MANUAL HPB25 Hydraulic Paving Breaker Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product at www.greenlee.com
More informationPure Water Power Purification System 4-Stage RODI Operations Manual
Pure Water Power Purification System 4-Stage RODI Operations Manual Flush Valve Lever Quick Disconnect for RO Water Testing Water Supply In Drain Hose Pure Water Out to Waterfed Pole New Machine Setup
More information200 PSI COMPRESSORS - MODEL NUMBERS
200 PSI COMPRESSORS - MODEL NUMBERS 380C AIR COMPRESSOR KIT PART NO. 38033 480C AIR COMPRESSOR KIT PART NO. 48043 380C 480C IMPORTANT: It is essential that you and any other operator of this product read
More informationRS Important Notes. Contact. Bicycle Maintenance Stand instructions manual. Warranty Period : 1 year (from the date of your purchase)
Warranty Period : 1 year (from the date of your purchase) RS-1700 Bicycle Maintenance Stand instructions manual (ver.1.2 2016/12) For more details, read the attached "Minoura Limited Warranty Policy" card.
More informationOperating instruction
Operating instruction MV, XV, HG, HP, RKO, D2G, TV, BV, WB & SLV 1 Introduction 2 2 Stafsjö s knife gate valves 2 3 Technical information 2 3.1 Pressure test 2 3.2 Labelling 2 4 Storage 3 5 Transportation
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS CAUTION - To reduce risk of electrical shock: - Do not disassemble. Do not attempt repairs or modifications. Refer to qualified service agencies for all service and repairs.
More informationTECHNICAL DATA MAINTENANCE AIR COMPRESSOR MODEL G-1
Dry 131h 1. DESCRIPTION The Viking Model G-1 Maintenance Air Compressor is an electric motor-driven, aircooled, single-stage, oil-less compressor. The unit is equipped with a check valve and provides a
More information6146XX-X OPEN STYLE HOSE REELS
OPERATOR S MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE 6146XX-XXX OPEN STYLE HOSE REELS LOW, MEDIUM & HIGH PRESSURE (FOR AIR, WATER & PETROLEUM PRODUCTS) 6146XX-X RELEASED: 2-5-90 REVISED:
More informationMODEL H8214 AIR BODY SAW INSTRUCTION MANUAL
MODEL H8214 AIR BODY SAW INSTRUCTION MANUAL COPYRIGHT SEPTEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL
More information100C Air Compressor Kit
10010 100C Air Compressor (standard mounting bracket, CE Spec) 10014 100C Air Compressor (no leader hose or check valve, CE Spec) 10016 100C Air Compressor (with Omega Bracket, CE Spec) IMPORTANT: It is
More informationG10K - 1/2" Heavy-Duty Air Impact Wrench
G10K - 1/2" Heavy-Duty Air Impact Wrench OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic
More informationMUELLER A A Non-Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3.
Installation Instructions manual MUELLER table of contents PAGE A-20808 General Information 2 Technical Data 3 Dimensions 4 A-20809 Non-Adjustable Installation 5-6 Parts 7 Maintenance 8 Vertical Indicator
More informationAgilent 1220 Infinity II LC Mobile Upgrade Kit
Agilent 1220 Infinity II LC Mobile Upgrade Kit Note 1220 Infinity II LC Mobile Upgrade Kit This note describes the procedures to install an Mobile Upgrade kit to an existing Agilent 1220 Infinity II LC.
More informationCS150 CAP STAPLER OWNER S MANUAL
Operation Revised 6/2013 www.stingerworld.com CS150 CAP STAPLER OWNER S MANUAL! Maintenance Safety Warranty PLEASE READ! This manual contains important information about product safety. WELCOME TO STINGER
More informationMODEL H RPM
MODEL H8217 3 8" REVERSIBLE ANGLE DRILL 0 1500 RPM INSTRUCTION MANUAL COPYRIGHT AUGUST, 2007 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
More informationFinal Assembly Instructions Bikes with Threaded Headsets
Final Assembly Instructions Bikes with Threaded Headsets Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our
More informationComponents for air preparation and pressure adjustment. OUT port position ( ) connected Rear side. of IN port. Air tank. directly.
Components preparation and pressure adjustment ABP Overview ABP is a component that enables boosting by s only up to twice primary pressure (.0MPa max.) in combination with using air tank but not using
More information420C AIR COMPRESSOR KIT PART NO C AIR COMPRESSOR KIT PART NO
420C AIR COMPRESSOR KIT PART NO. 42042 460C AIR COMPRESSOR KIT PART NO. 46043 420C 460C IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this
More informationAIR/OVER HYDRAULIC JACK 20 TON
AIR/OVER HYDRAULIC JACK 0 TON 4487 ASSEMBLY AND OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 999 by Harbor Freight Tools.
More informationGeneral Information. NTA607HD Lift Assist Adjustments. Tools Required. Work Location. Notations and Conventions U B F D R B F L
Great Plains Manufacturing, Inc. 1 NTA607HD Lift Assist Adjustments Null4: When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives
More informationInstallation Operating Instructions for Simple Duplex Manual Manifolds PX-TSD Series
Introduction Powerex manifolds are cleaned, tested and prepared for the indicated gas service and are built in accordance with the Compressed Gas Association guidelines. The manifold consists of a regulator
More information2 in. 18 Gauge Brad Nailer. User manual
8504342 2 in. 18 Gauge Brad Nailer User manual Technical Data Capacity....100pcs Nail length... 15-50mm( 5/8-2 ) Fastener size....18gauge (1.25 1.00mm) Operation pressure 70-110PSI(4.8-7.5bar) Air inlet....1/4
More informationOperation Manual Guillotine Cutter RC-5
Operation Manual Guillotine Cutter RC-5 Technical Specifications General Safety/Operating Instructions Using the Guillotine Cutter/Crimper Blade Change Instructions Maintenance Instructions This is a detailed
More informationSide-of-Pole Mount for 1 Modules (SPM1) For Module Types E, F, G, & H ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation
Side-of-Pole Mount for 1 Modules (SPM1) For Module Types E, F, G, & H ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A SP3348-1 PCN 022212-2 Side-of-Pole Mount for 1 Module
More informationRT3 CAP NAILER OWNER S MANUAL Operation Safety Maintenance Warranty! www.stingerworld.com PLEASE READ! This manual contains important information about product safety. REV 09/14 WELCOME TO STINGER Congratulations
More informationPNEUMATIC SEALER MODEL A
OPERATION MANUAL / SPARE PARTS LIST PNEUMATIC SEALER MODEL A461.0002 13.4510.01-13.4511.01 CE Declaration of conformity 13451001.en/MAS/ 02.04 13451101.en We declare that the machine A461 is in conformity
More informationCLEATBENDER MODEL A OPERATION & MAINTENANCE MANUAL
CLEATBENDER MODEL A OPERATION & MAINTENANCE MANUAL Manual# LMMODELA June 2005 Copyright by Lion Machinery A member of the Formtek Group All Rights Reserved The information in this document has been reviewed
More informationRATCHET RELEASE SHACKLE
RATCHET RELEASE SHACKLE INNOVATIVE PILING EQUIPMENT HYDRAULIC PILING HAMMERS EURO RATCHET RELEASE SHACKLE FOR STEEL ERECTION OPERATORS INSTRUCTIONS & SPARE PARTS LIST EXCAVATOR MOUNTED VIBRATORS EXCAVATOR
More informationPortable Hydrostatic Pneumatic Test Pump. Procedure Manual
Portable Hydrostatic Pneumatic Test Pump Procedure Manual Dixon Valve & Coupling Company 800 High Street Chestertown, MD 21620 800-355-1991 Fax: 800-283-4966 Specifications Dixon Portable Pneumatic Hydrostatic
More informationPNEUMATIC SEALER MODEL A
OPERATION MANUAL / SPARE PARTS LIST PNEUMATIC SEALER MODEL A461.0002 13.4512.01-13.4513.01 13451201.en/MAS/ 02.04 13451301.en CE Declaration of conformity We declare that the machine A461 is in conformity
More information602 STRINGING MACHINE OWNER'S MANUAL
PROGRESSION 602 STRINGING MACHINE OWNER'S MANUAL AL Issue 1- April 2000 Copyright 2000 GAMMA Sports - All Rights Reserved PROGRESSION 602 STRINGING MACHINE TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2...
More informationModel Air Caddy Orig TABLE OF CONTENTS
92-0919 Orig. 020201 Model 75-0114 Air Caddy TABLE OF CONTENTS CUSTOMER MESSAGE Inside Front Cover SAFETY PRECAUTIONS 3 GENERAL DESCRIPTION 6 SPECIFICATIONS 7 MAINTENANCE 9 INSTALLATION AND OPERATION 11
More informationPF30 Inspection & Maintenance Manual
PF30 Inspection & Maintenance Manual Version 1.4 (September 2011) 1 Contents 1. Warning!!!!!!!!!! 3 2. Terminology! Figure 1: POWERFAN PF30 and Drope!!!! 4! Figure 2: POWERFAN PF30 with belt guard retracted!!
More informationInstruction Manual. PE-25/32/37 Tapping Machines. POLYTAPP Valves
Instruction Manual PE-25/32/37 Tapping Machines & POLYTAPP Valves Nov 2016, Revision 2 Document Number 3000111 2 M.T. Deason Company, Inc. PO Box 101807 Birmingham, AL 35210 Phone: 205 956 2266 Fax: 205
More informationU.S. Patent No. 7,922,246. Patents Pending
U.S. Patent No. 7,922,246 Patents Pending 2 Table of Contents Page General Information... 3 Warnings and Cautions... 4 Tools... 6 SmartDock Parts... 6 Initial Set-Up and Adjustment... 7 Select Valve Retaining
More informationInstallation and Operation Instruction Manual
Installation and Operation Instruction Manual Toggle Lok Anchor - Model #7442 Portable Concrete Anchorage Connector ANSI Z359.1 5,000 lbs / 22.24 kn FallTech, Inc 1306 Alameda Street Compton, CA 90221
More informationSqueegee Unit for MRS Multi-Recovery System
En Operating Instructions Squeegee Unit for MRS Multi-Recovery System Translation of the original operating instructions Squeegee - MRS Table of Contents Safety Recommendations Technical Data - MRS Booth
More information! CAUTION! ! WARNING! General Information
Great Plains Mfg., Inc. Installation Instructions Used with: 2SF24, 24-Foot Two-Section Drill General Information Two-Section, Hydraulic Folding Marker 2SF30, 30-Foot Two-Section Drill 2SBM30, 30-Foot
More informationQUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift
INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your
More information