2016 Road Frame Fit Specifications This document is intended to communicate general frame fit guidelines for SRAM road group sets.

Transcription

1 2016 Road Frame Fit Specifications This document is intended to communicate general frame fit guidelines for SRAM road group sets. For additional information, please contact your SRAM representative. Gen Rev D 2016 SRAM, LLC

2 Table of Contents ELECTRIC SHIFTERS... 5 BLIPBOX BLIPS...9 BLIPBOX AND BLIPS...10 BLIP CLAMP AND BLIPGRIP ETAP SHIFT/BRAKE LEVERS ELECTRIC FRONT DERAILLEUR...13 RED ETAP X11 FRONT DERAILLEURS RED/FORCE/RIVAL X10 FRONT DERAILLEURS...26 APEX MM OLD FRONT DERAILLEURS...32 REAR DERAILLEURS X11 - RED/FORCE/RIVAL X11 - FORCE 1/RIVAL X10 - APEX X11 CRANKSETS...38 CHAINSTAY LENGTH CRANKSET MEASUREMENT DIAGRAM - 2X RED RED QUARQ POWER METERS/FORCE/S902/S RIVAL/S X11 CRANKSETS CRANKSET MEASUREMENT DIAGRAM - 1X FORCE RIVAL S X10 AND 1X1 CRANKSETS...49 CRANKSET MEASUREMENT DIAGRAM - 2X CRANKSET MEASUREMENT DIAGRAM - 1X10/1X RIVAL OCT S901/S S900/S S500/S APEX/ELITA/S300/S TOURO/S100/S ISOFLOW OMNIUM... 59

3 WIDE AXLE CRANKSETS CRANKSET MEASUREMENT DIAGRAM - WIDE AXLE RIVAL/S552 WIDE AXLE S902/S952 WIDE AXLE S500/S550 WIDE AXLE BOTTOM BRACKETS...67 PRESSFIT GXP PRESSFIT GXP OLD WIDE AXLE PRESSFIT GXP ENGLISH/GXP ITALIAN/POWERSPLINE...72 BB BRAKES...74 RED/FORCE/RIVAL/S RED/FORCE/RIVAL/S RED/FORCE/RIVAL RED/FORCE/RIVAL/S700/BB7/BB5 ROAD BB7/BB5 ROAD RED/FORCE/RIVAL/APEX/S RED/FORCE/RIVAL/APEX/S SINGLE DIGIT...87 SINGLE DIGIT SHORTY ULTIMATE SHORTY 6/SHORTY WHEELS ZIPP WHEELS DRIVER AND WHEEL STANDARD - ROAD REAR MAXLE FRONT MAXLE

4 All dimensions are in millimeters unless otherwise noted. Images in this document are not to scale. Your product's appearance may vary slightly from the images in this document. Information in this document is subject to change without prior notice. If you have any questions please contact your SRAM representative.

5 Electric Shifters

6 BlipBox BlipBox Wireless Shifter Dimensions 18 mm 40.6 mm 61.5 mm 2 Front (Button side) Side Back (Battery/Mount) Notes: 1 Overall dimensions are subject to change during the development. 2 Button access needed for pairing and adjustment of the derailleurs Rev D Electric

7 BlipBox BlipBox Wireless Shifter with Connectors 18 mm 1 72 mm Notes: 1 Allow sufficient space for shifter and connector length in desired mounting location Rev D Electric

8 BlipBox Mounting Specifications Lock mount Threaded direct mount M4x0.7 thread pitch, 4.6 mm depth Notes: Consider additional clearance for 90 lock mount Cable connections can be made after mounting with proper port access. Button access is only needed for setup. 90 mount is compatible with all SRAM/Zipp Quickview mounts. BlipBox must be mounted externally on the bike to maintain integrity of the wireless signal Rev D Electric

9 Blips Remote Shift Buttons and Connector Dimensions Left shift button Right shift button 1 2 Wire lengths 150 mm 230 mm 450 mm 650 mm 2.5 mm wire diameter mm mm connector diameter Notes: 1 Consider the connector diameter and wire length when routing wires internally. 2 Choose the wire lengths based on application and desired location of the Blips Rev D Electric

10 BlipBox and Blips Internal Mounting Specifications Side A Side B 100 mm mm Notes: 1 2 Internally mounted shifter setup requires the Blip wires to be routed external of bar, stem, and frame materials a minimum of 100 mm per side. Routing under bar tape is acceptable within the 100 mm length Rev D Electric

11 Blip Clamp and BlipGrip Remote Shifter Mounting mm bar 31.8 mm bar mm TT Extensions Notes: 1 Button holder designed for 31.8 mm bar mounting. 2 Direct mount under the handlebar tape for 22.2 mm through 35 mm diameter bars Rev D Electric

12 etap Shift/Brake Levers Remote Shifter Connections 2 Notes: The left and right shifter brake each provide two additional ports for auxiliary remote shifter buttons. Use plugs when remote shifters are not in use. Provide a small amount of slack in the wire for shifter brake repositioning. Route the wires underneath the bar tape Rev D Electric

13 Electric Front Derailleur

14 RED etap Front Derailleur Dimensions Hanger contact face Fixation bolt center Rev D Electric Front Derailleur

15 RED etap Front Derailleur Frame Compatibility and Capacity Information Chainring Chainline A (mm) Fixation bolt position B Chainstay angle C (mm) Chainstay length 55/ / x11 52/36 45 mm / / * For 32T cassettes the chainstay angle (B) is B A C Rev D Electric Front Derailleur

16 RED etap Front Derailleur Cage Alignment Chainring D (mm) Hanger offset from seat tube axis E Hanger angle relative to seat tube axis F (mm) G (mm) Outer cage position above chainring 55/42 53/39 2x11 52/ ± 0.5 ± 1.5 > ± /34 46/36 D E G F Rev D Electric Front Derailleur

17 RED etap Position of Front Derailleur with Clamp Adapter Chainring H (mm) Lower clamp position I (mm) Upper clamp position 55/ / x11 52/ / / H I BB Axis Rev D Electric Front Derailleur

18 RED etap Clearance Between Front Derailleur and Frame A (mm) B (mm) C (mm) D (mm) E (mm) F (mm) 130 OLD: Clearance Between Front Derailleur and Crank Arm G (mm) H (mm) Fixation bolt center A 27 A A G Bottom bracket center 8.7 Ø B 57 C Fixation bolt center D E F H Tire clearance to battery 20.1 D Rev D Electric Front Derailleur

19 RED etap Braze-on Hanger Dimensions R ±0.5 mm Center line of seat tube to center line of bottom bracket 8.7 R Rev D Electric Front Derailleur

20 2x11 Front Derailleurs

21 RED/Force/Rival Front Derailleur Frame Compatibility and Capacity Information Chainring Cable routing Chainline A (mm) Fixation bolt position B Chainstay angle* C (mm) Chainstay length 55/ / x11 52/36 Bottom pull (N/A for Electronic) 45 mm / / * For 32T cassettes the chainstay angle (B) is B A C Rev D 2x11 Front Derailleurs

22 RED/Force/Rival Front Derailleur Cage Alignment Chainring D (mm) Hanger offset from seat tube axis E Hanger angle relative to seat tube axis F (mm) G (mm) Outer cage position above chainring 55/42 53/39 2x11 52/ ± 0.5 ± 1.5 > ± /34 46/36 E D G F Rev D 2x11 Front Derailleurs

23 RED/Force/Rival Position of Front Derailleur with Clamp Adapter Chainring H (mm) Lower clamp position I (mm) Upper clamp position 55/ / x11 52/ / / H I BB Axis Rev D 2x11 Front Derailleurs

24 RED/Force/Rival Clearance Between Front Derailleur and Frame A (mm) B (mm) C (mm) D (mm) E (mm) F (mm) 130 OLD: Clearance Between Front Derailleur and Crank Arm G (mm) H (mm) A A A B B G Bottom bracket center Fixation Bolt Center C E F H D D Rev D 2x11 Front Derailleurs

25 RED/Force/Rival Braze-on Hanger Dimensions R ±0.5 mm Centerline of seat tube to centerline of bottom bracket 8.7 R Rev D 2x11 Front Derailleurs

26 2x10 Front Derailleurs

27 Apex Front Derailleur Frame Compatibility and Capacity Information Chainring Cable routing Chainline A (mm) Fixation bolt position* B Chainstay angle C (mm) Chainstay length 2x10 55/ (lower hole) 54/ (lower hole) 53/ (lower hole) 52/36 Bottom pull 46 mm 148 (lower hole) 52/ (lower hole) 50/ (upper hole) 46/ (upper hole) * Mounting holes are spaced 8.5 mm apart B A C Rev D 2x10 Front Derailleurs

28 Apex Front Derailleur Cage Alignment Chainring D (mm) Hanger offset from seat tube axis E Hanger angle relative to seat tube axis F (mm) G (mm) Outer cage position above chainring 55/42 54/42 53/39 2x10 52/ ± 0.5 ± 1.5 > ± /38 50/34 46/36 E D G F Rev D 2x10 Front Derailleurs

29 Apex Position of Front Derailleur Clamp Chainring H (mm) Lower clamp position I (mm) Upper clamp position 55/ / / x10 52/ / / / H I BB Axis Rev D 2x10 Front Derailleurs

30 Apex Clearance Between Front Derailleur and Frame A (mm) B (mm) C (mm) D (mm) E (mm) F (mm) (upper hole) 27.7 (upper hole) Clearance Between Front Derailleur and Crank Arm G (mm) H (mm) A A A B B G Bottom bracket center Fixation Bolt Center C E F H D D Rev D 2x10 Front Derailleurs

31 Apex Braze-on Hanger Dimensions R ±0.5 mm Centerline of seat tube to centerline of bottom bracket 8.7 R Rev D 2x10 Front Derailleurs

32 135 mm OLD Front Derailleurs

33 135 mm OLD Position of Front Derailleur with Clamp Adapter and Braze-On Frame BB shell width [GXP, BB30, PF30] Crankset Chainline (mm) FD placement (mm) Available clamp diameters (mm) Q-factor (mm) Braze-on Clamp adapter 73 mm (or 68 mm plus spacers)* SRAM 135 mm OLD Specific Crankset Required *68 mm BB shells may be spaced to 73 mm by installing a 2.5 mm BB cup spacer. GXP uses the spacer behind the BB cup, and BB30 models use the spacer on the outside of the BB cup shields. Notes: Frame BB shell width and rear hub OLD are measured in total width. Chainline and FD placement are measured from the centerline of the bike. Standard Braze-on and Clamp Adapter 135 Braze-on 135 SRAM Clamp Adapter Drawings not to scale 68 mm 73 mm 73 mm 25 mm 27.5 mm 27.5 mm Rev D 135 mm OLD

34 Rear Derailleurs

35 2x11 - RED/Force/Rival Rear Derailleur Hanger Specifications L (mm) X (mm) A R1 (mm) R2 (mm) T (mm) D (mm) (max) ± 1.5 Rear Derailleur Hanger R2 R1 A L 90 To center of bottom bracket T T T X D Rev D Rear Derailleurs

36 1x11 - Force 1/Rival 1 Rear Derailleur Hanger Specifications L (mm) X (mm) A R1 (mm) R2 (mm) T (mm) D (mm) (max) ± 1.5 Rear Derailleur Hanger R2 R1 A L 90 To center of bottom bracket T T T X D Rev D Rear Derailleurs

37 2x10 - Apex Rear Derailleur Hanger Specifications L (mm) X (mm) A R1 (mm) R2 (mm) T (mm) D (mm) (max) ± 1.5 Rear Derailleur Hanger R2 R1 A L 90 To center of bottom bracket T T T X D Rev D Rear Derailleurs

38 2x11 Cranksets

39 Chainstay Length 135 mm OLD Minimum Chainstay Length Requirements Chainring A (mm) 55/42 NA 53/ x11 52/ mm 50/ mm 46/ mm *Please refer to Wide Axle crankset section for shorter chainstay lengths. A Rev D 2x11 Cranksets

40 Crankset Measurement Diagram - 2x11 L1 L2 W5 W4 W3 W1 L3 L4 L5 W Rev D 2x11 Cranksets

41 RED Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 55/ / x11 52/ / / Q-factor : 145 Bottom Bracket Type : GXP : PFGXP : BB30 : PF Rev D 2x11 Cranksets

42 RED Quarq Power Meters/Force/S902/S952 Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 55/ / x11 52/ / / Q-factor : 145 Bottom Bracket Type : GXP : PFGXP : BB30 : PF Rev D 2x11 Cranksets

43 Rival/S552 Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 52/ x11 50/ GXP PFGXP 60.3 BB30 PF GXP PFGXP 60.1 BB30 PF30 46/ Q-factor : (GXP : PFGXP) (BB30 : PF30) Bottom Bracket Type : GXP : PFGXP : BB30 : PF Rev D 2x11 Cranksets

44 1x11 Cranksets

45 Crankset Measurement Diagram - 1x11 L1 L2 W5 W3 W1 L4 L5 W Rev D 1x11 Cranksets

46 Force 1 Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W5 (mm) W6 (mm) x Q-factor : 145 Bottom Bracket Type : GXP : PFGXP : BB30 : PF Rev D 1x11 Cranksets

47 Rival 1 Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W5 (mm) W6 (mm) x GXP PFGXP 60.3 BB30 PF GXP PFGXP 60.1 GXP PFGXP Q-factor : (GXP : PFGXP) (BB30 : PF30) Bottom Bracket Type : GXP : PFGXP : BB30 : PF Rev D 1x11 Cranksets

48 S350-1 Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W5 (mm) W6 (mm) Q-factor : 145 Bottom Bracket Type : GXP : PFGXP : BB30 : PF Rev D 1x11 Cranksets

49 2x10 and 1x1 Cranksets

50 Crankset Measurement Diagram - 2x10 L1 L2 W5 W4 W3 W1 L3 L4 L5 W Rev D 2x10 and 1x1 Cranksets

51 Crankset Measurement Diagram - 1x10/1x1 L1 L2 W5 W3 W1 L4 L5 W Rev D 2x10 and 1x1 Cranksets

52 Rival OCT with Powerglide Chainrings Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 53/ x10 52/ / / / / / Q-factor : 147 Bottom Bracket Type : GXP : PFGXP Rev D 2x10 and 1x1 Cranksets

53 S901/S951 Yaw Compatible Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 2x10 55/42 TT / / Q-factor : 145 Bottom Bracket Type : GXP : PFGXP : BB30 : PF Rev D 2x10 and 1x1 Cranksets

54 S900/S950 with Powerglide Chainrings Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 55/42 TT /42 TT / x10 52/ / / / / / Q-factor : 145 Bottom Bracket Type : GXP : PFGXP : BB30 : PF Rev D 2x10 and 1x1 Cranksets

55 S500/S550 with Powerglide Chainrings Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5(mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 53/ x10 52/ / / / / / Q-factor : 145 Bottom Bracket Type : GXP : PFGXP : BB30 : PF Rev D 2x10 and 1x1 Cranksets

56 Apex/Elita/S300/S350 with Powerglide Chainrings Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) L6 (mm) W1 (mm) W2 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 53/ x10 52/ / / / n/a n/a / / x n/a n/a Q-factor : 145 Bottom Bracket Type : GXP : PFGXP : BB30 : PF Rev D 2x10 and 1x1 Cranksets

57 Touro/S100/S150 with Powerglide Chainrings Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 53/ x10 52/ / / / / x1 1x n/a n/a 71.0 G Q-factor : 145 Bottom Bracket Type : PowerSpline Rev D 2x10 and 1x1 Cranksets

58 IsoFlow with Powerglide Chainrings Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 2x10 50/ x G Q-factor : 145 Bottom Bracket Type : PowerSpline Rev D 2x10 and 1x1 Cranksets

59 Omnium Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W5 min (mm) W6 min (mm) 1x Q-factor : 135 Bottom Bracket Type : GXP : PFGXP Rev D 2x10 and 1x1 Cranksets

60 Wide Axle Cranksets

61 Crankset Measurement Diagram - Wide Axle L1 L2 W5 W4 W3 W1 L3 L4 L5 W Rev D Wide Axle Cranksets

62 Rival/S552 Wide Axle Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 2x11 52/ / (BB30) (BB30) Q-factor : (GXP : PFGXP) (BB30 : PF30) Bottom Bracket Type : GXP : BB30 : PF Rev D Wide Axle Cranksets

63 S902/S952 Wide Axle Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 55/ / x11 52/ / / Q-factor : 150 Bottom Bracket Type : GXP : BB30 : PF Rev D Wide Axle Cranksets

64 S500/S550 Wide Axle with Powerglide Chainrings Crankset Frame Clearance Information Chainring L1 (mm) L2 (mm) L3 (mm) L4 (mm) L6 (mm) W1 (mm) W3 (mm) W4 (mm) W5 min (mm) W6 min (mm) 2x10 53/ / Q-factor : 150 Bottom Bracket Type : GXP : BB30 : PF Rev D Wide Axle Cranksets

65 135 mm OLD frame The diagram below illustrates the potential problems of using a crankset designed for a 130 mm OLD frame on a 135 mm OLD frame. 130 mm OLD Frame 68 mm BB shell Clamp Adapter 65 mm Interference in the small chainring 67.5 mm 135 mm OLD Frame 68 mm BB shell Clamp Adapter WARNING - CRASH HAZARD When the chain is on the small chainring and smallest rear cog, reduced clearance between the chain and large chainring upshift rivets can cause the chain to unintentionally catch on the upshift rivets, which may lead to loss of control of the bicycle Rev D Wide Axle Cranksets

66 135 mm OLD frame The diagram below illustrates the potential problems of using a crankset designed for a 130 mm OLD frame on a 135 mm OLD frame. 130 mm OLD Frame 68 mm BB shell Clamp Adapter 65 mm Increased Chain Angle in the large chainring WARNING - CRASH HAZARD Increased chain angle can cause the chain to derail outboard off of the large chainring under very high pedaling loads, which may lead to a crash and serious injury and/or death to the rider mm 135 mm OLD Frame 68 mm BB shell Clamp Adapter NOTICE Due to limited clearance, contact between chain and crank arm is likely under hard pedaling load Rev D Wide Axle Cranksets

67 Bottom Brackets

68 PressFit GXP 86.5 mm Road Symmetric Shell Specifications A 86.5 ± Ø A -A- I Frame Center 86.5 mm Road Symmetric Bottom Bracket Specifications Item Number Quantity Description Notes 1 2) 1 1 Wave Washer 2 1 DS Shield 3 1 NDS Shield 4 1 DS Cup 5 1 NDS Cup GXP integrated adapter is only compatible with the bottom bracket shell specifications shown. Only dimensions essential to bottom bracket PressFit and function are shown. Dimensions apply after finishing. Non-Drive Side (NDS) 3 (2X) 3 Ø44 (2X) ± Drive Side (DS) 3 4 5) Tolerance applies to depth of 14 mm from surface -A-, on each side. PressFit surfaces should be unpainted. 180 kg is the maximum recommended frame press-in force. Ø27.8 Ø PressFit region (2x) Rev D Bottom Brackets

69 PressFit GXP OLD Wide Axle 91.5 mm Road Symmetric Shell Specifications A 91.5 ± Ø A -A- I Frame Center 91.5 mm Road Symmetric Bottom Bracket Specifications Item Number Quantity Description 1 1 Wave Washer 2 1 DS Shield 3 1 NDS Shield 4 1 DS Cup 3 (2X) ± Notes 1 2) 5 1 NDS Cup GXP Integrated adapter is only compatible with the bottom bracket shell specifications shown. Only dimensions essential to bottom bracket PressFit and function are shown. Dimensions apply after finishing. Non-Drive Side (NDS) 3 Ø44 (2X) 1 Drive Side (DS) 3 4 5) Tolerance applies to depth of 14 mm from surface -A-, on each side. PressFit surfaces should be unpainted. 180 kg is the maximum recommended frame press-in force. Ø27.8 Ø PressFit region (2x) Rev D Bottom Brackets

70 PressFit 30 SRAM PressFit 30 (PF30) bottom brackets have been designed and tested to work within the bounds of the dimensions and tolerances in the shell specifications and bottom bracket specifications. Materials, manufacturing methods, and frame shell designs can potentially influence the performance of the bottom bracket, even when the shell is manufactured to these specifications. In these instances, it is recommended that bicycle manufacturers confirm the bottom bracket system performance with individual frame configurations. Things that should be considered when evaluating the frame and bottom bracket interaction include, but are not limited to: Loosening of the adapter cups from the bottom bracket shell (frame material choice can greatly affect friction coefficient). Binding of bearings within the bottom bracket. For more information regarding PF30 bottom bracket technical information, contact your SRAM representative. Shell Specifications B W ± MIN 2X 1±0.5 X 45 (NDS) DS ± MIN A 0 Ø Ø0.1 A Ø44.5 MIN 0 Ø Dim W 4 B Dim DS Dim NDS 3 Frame Center PF PF30 79 ASYM Notes Dimensions apply after finishing. Only dimensions essential to bottom bracket PressFit and function are shown. All other details are left to the discretion of the frame or component designer. Dimensions shown do not take the place of proper frame, bottom bracket shell, or crankset design. PressFit surfaces should be unpainted. Recommended 68 mm or 79 mm for road applications Rev D Bottom Brackets

71 PressFit 30 Continued Bottom Bracket Specifications Dim W 3 Dim DS PF Dim NDS PF30 79 ASYM Notes Dimensions apply after finishing. Only dimensions essential to bottom bracket PressFit and function are shown. All other details are left to the discretion of the frame or crankset designer. Dimensions shown do not take the place of proper frame, bottom bracket shell, or crankset design. Recommended 68 mm or 79 mm for road applications. B B 1.5 (2X) W ±.20 3 See detail Z Detail Z : Crank bottom bracket interface scale 5 : 1 Non-Drive Side (NDS) Ø44 Ø (2X) Ø52 (2X) Drive Side (DS) BB shell shown for reference 0.04 (2x) BB Shell to Shield Outerface - DS 11.5 ± 0.2 PressFit region (2x) ± 0.2 PressFit region (2x) W+.08 to Shield - Outerface - NDS Ø46.76 (2X) NDS Frame Center DS Shield - Outerface - DS Rev D Bottom Brackets

72 GXP English/GXP Italian/PowerSpline Shell Specifications A B C (mm) Minimum usable threads D (mm) Bottom bracket dimension GXP English PowerSpline Square Taper 1.37" x 24 TPI R.H. Class 2A 1.37" x 24 TPI L.H. Class 2A or 73 ± 0.5* GXP Italian 36 mm x 24 TPI R.H. Class 2A 70 ± 0.5 *2.5 mm spacers may be used between the frame-shell and the adapter cups to adjust BB spacing. A B C Non-Drive Side (NDS) Chamfer DO NOT EXCEED Ø mm Drive Side (DS) D Rev D Bottom Brackets

73 BB30 Information for the BB30 drawing and legal agreement can be found on Use of the information contained in the drawing is forbidden without reviewing and agreeing to the legal terms and conditions found on By using the information contained in the drawing you are certifying that you have agreed to the terms and conditions found within that legal agreement Rev D Bottom Brackets

74 Brakes

75 RED/Force/Rival/S700 Road Hydraulic Disc Brake Safety Guidelines for Rotor Size and Brake Pad Material Brake pad material Minimum rotor size (mm) Riding Conditions Road Riding Organic 160 Cyclocross Racing Organic or Metal Sintered 140 WARNING - CRASH HAZARD SRAM disc brakes pass laboratory testing designed to simulate worst case riding conditions. The rotor size and pad compound materials recommendations were generated through controlled testing. Use of any combination not mentioned above will void the warranty and could result in a crash Rev D Brakes

76 RED/Force/Rival/S700 Disc Brake Mount Specification Frame Mount - QR Dropout Fork Mount - QR Dropout Frame Clearance 95 min min 38 min Rev D Brakes

77 RED/Force/Rival/S700 Disc Brake Mount Specification Direct mount rotor size A (mm) B (mm) C (mm) D (mm) 140 mm mm Note: The minimum threaded depth for the mounting holes in the frame is 14 mm. Chainstay Mount Seatstay Mount Fork Mount B 74.2 ±0.1 D 74.2 ±0.1 A C D B 74.2 ±0.1 A A C C B D Rev D Brakes

78 RED/Force/Rival/S700 Disc Brake Hose Length Specification 4 Hose length ±10 mm Hose boot Attach to caliper here Banjo connection under reservoir cover Ø5.1 max 4 20 mm 4 Hose length Notes 1 4 Hose length ±10 mm Connectamajig quick disconnect for initial assembly only. See Connectamajig specification for dimensions and details. 3 Inline CJ located here 2 Caliper Connectamajig is located here. The hose fitting feeds through the frame from front to back. Specify caliper hose exit angle per hose angle specification. 3 Hose inline Connectamajig is located here. The hose fitting feeds through the frame from back to front. 4 Measure hose length from the hood bolt to the caliper fitting. The hood bolt starts approximately 20 mm from the end of the hood, as shown. 5 Hose bend radius at 20 C = 30 mm minimum; Hose diameter Ø 5.1 maximum. 2 Caliper CJ located here 6 Brake system and brake system Connectamajig are not compatible with mineral based fluids such as damping fluid, mineral oil, fork fluid, or RockShox Reverb fluid Rev D Brakes

79 RED/Force/Rival/S700 Disc Brake Mounting Bracket and Spacing Specification 25 S 10 S 25 S 10 S Use the chart to determine the bracket and/or spacer configuration to mount your disc brake caliper to your frame/fork. Rotor Size (mm) Standard Fork/Frame Mount 140 mm 160 mm 170 mm 180 mm 140 IS 0 IS 20 IS 30 IS 40 IS 140 Post 0 Direct 20 S 20 P 30 P 40 P 160 IS 0 IS 20 IS 160 Post Direct 10 S 20 S 20 P 180 Post Direct 25 S 10 S 25 S 25 S 10 S 25 S 25 S 10 S 10 S Direct 10 S Direct 25 S S Upper Bolt 3 S 20 S 20 S 30 P Direct 16.8 mm N/A 16.8 mm N/A S Direct Post Mount 10 S 24 mm 6 mm 24 mm 6 mm 10 S Upper Spacer 3 S 3 S Lower Bolt 20 P/30 P 10 Post Spacer Lower Spacer IS IS Direct Direct 25 S Direct Direct 20 S 20 S Direct Direct 10 S 25 S 20 S 20 S 20 S Rev D Brakes 25 S 30 P 20 S 10 S 20 P/30 P Direct Direct 30 P 20 P/30 P 25 S 30 P 20 S 20 P/30 P 10 S 20 S IS IS Direct Direct Direct Direct 20 S 20 S 20 S 20 S 3 S IS IS 30 P 10 S 40 P 20 P/30 P IS 40 P IS P 20 P/30 P 20 P/30 P 37.5 mm 3 S IS IS 40 P IS IS 40 P IS IS 20 S / 20 P 12.5 mm 20 P: N/A 32 mm 20 Post Spacer / 20 Post Bracket 40 P 30 P 40 P 7.5 mm 20 P: N/A 46 mm N/A 37.5 mm N/A 30 Post Bracket 40 P 16.8 mm N/A 16.8 mm N/A 40 P 40 P 40 P P P 40 Post Bracket IS 16.8 mm N/A 16.8 mm N/A IS (0 IS, 20 IS, 30 IS, 40 IS)

80 RED/Force/Rival Flat Mount Caliper Front Frame Specification Min 10 mm depth M5x0.8-6H (2X) Min 13 mm Boss diameter 40 max dropout angle Co-planar mounting surfaces 70 ±0.15 Bolt hole spacing 1.7±0.4 Dropout face to hole pattern centerline 23.5 ± ±0.15 Dropout to mounting face See hub specification for dropout face to rotor mounting face dimension Rev D Brakes

81 RED/Force/Rival Flat Mount Caliper Rear Frame Specification 16 ±0.15 Min dropout angle 69 Rear mount thickness 10, 15, 20, 25, 30, or 35 ±0.5 Underside of boss to accommodate 11 mm diameter washer. 5.2 ±0.1 Ø14 min Boss diameter See hub specification for dropout face to rotor mounting face dimension +0.5 (2X) Slot width 34 ±0.15 Slot spacing 36.5 ±0.15 Rear slot centerline to axle centerline (2X) 2.05 ±0.4 Dropout face to outboard most mounting location Rev D Brakes

82 RED/Force/Rival/S700/BB7/BB5 Road Spoke Clearance 160 mm ± mm ± mm ± mm ± Rotor Mounting Face Min Min Min Hub Axis Min Min Notes 1 Caliper body will not extend beyond this datum. Datum accounts for caliper manufacturing tolerances and variation in pad advancement mm rotor dimensions apply only to rear wheel setups. All other dimensions apply to both front and rear wheel setups. Caliper position shown for 160 mm rotor Rev D Brakes

83 BB7/BB5 Road Mechanical Disc Brakes Clearance Rev D Brakes

84 RED/Force/Rival/Apex/S700 Rim Brake Caliper Caliper Brake Pivot Location (Short Reach mm) Dim A Max Dim B Min Note: For maximum tire clearance, use the top 1/3 of the graph. Dim B Dim A Front Rim Brake Caliper B 90 Rear Rim Brake Caliper 90 B A A (-) (+) Rev D Brakes (+) (-)

85 RED/Force/Rival/Apex/S700 Rim Brake Caliper When designing a bicycle frame, consider these SRAM brake caliper dimensions Front Brake Caliper Rear Brake Caliper Rev D Brakes

86 Brake Specifications Caliper and Lever Compatibility Levers/Brakes RED/Force/Rival/ Apex Single Digit Shorty Shorty Ultimate BB7 MTB & BB5 MTB BB7 Road & BB5 Road Speed Dial x x FR-5 x x RED/Force/Rival/ Apex/S500/S900/ S700/Hydro R x x x x Aero/ BL 700 x x x x Range of Speed Dial FR-5 Speed Dial 7 & SL Min Cable Pull 25 mm 25 mm Leverage Ratio 2 : 1 2 : 1 Max Cable Pull 29 mm 32 mm Leverage Ratio 2.75 : : 1 Notes Brake levers with a cable pull of more than 32 mm are compatible with Avid Single Digit, BB7 MTB, and BB5 MTB mechanical disc brakes, but reduce brake power. Avid Single Digit, BB7 MTB, and BB5 MTB mechanical disc brakes are compatible with virtually all side-pull specific brake levers. As with any side-pull brake, it is recommended to use adjustable leverage brake levers when using Single Digit, BB7 MTB, and BB5 MTB mechanical disc brakes Rev D Brakes

87 Single Digit Link to Arm Dimension The link must be a minimum of 38 mm from the inside edge of the cable arm to prevent the link from contacting the cable anchor arm. If the link and arms are too far apart, the top of the brake arm can extend too far from the frame or fork and interfere with the rider's feet. > 38 mm Brake Pad Adjustment Slot Single Digit Brakes Min mm Max 35 mm 19 mm 38 mm 19 mm Rev D Brakes

88 Single Digit Cable Link / Noodle / Boot WARNING - CRASH HAZARD Roller-Type Noodles: Do not use roller-type noodles with Avid side-pull brakes. Due to the radius of most roller-type noodles, and the diameter of the brake cable, there is a safety concern. The Avid cable link on all side-pull brakes is made of stainless steel and is riveted onto the brake arm. It is specifically designed for use with the Avid noodle. The Avid noodle on Single Digit 7/SL is specifically designed to allow the installation and removal from the link without removing the Overcoat boot from the noodle tip. The noodle is available in the following bends: 90, 110, and 135 degrees. Overcoat Boot Installation Rev D Brakes

89 Shorty Ultimate Dual Mounted Brake Caliper *For wheel rims wider than 23 mm (ex. Zipp 303 Cyclocross), consult the spare parts catalog on sram.com/service part numbers. 250 mm straddle wire (recommended) 145 mm to top of cable hanger 90 (recommended) mm rim width* mm brake boss spacing Rev D Brakes

90 Shorty 6/Shorty 4 Cable Carrier and Straddle Cable Length CCC Type S CCC Type A CCC Type B CCC Type D CCC Type C A (mm) Lenth of straddle cable C Opening angle of straddle cable D (mm) Designed width of Shorty H (mm) Total height h (mm) Designed height W (mm) Total width Pivot width Opening W/ mm rim width A C/2 H Opening h 56.8 D mm brake boss spacing Rev D Brakes

91 Wheels

92 Zipp Wheels Zipp Rim/Disc Design Parameters Rim/Disc A (mm) Max width B (mm) Depth at max width (A) C (mm) Max depth R1 (mm) Radius to center line Frame clearance 4 mm minimum per side A 202 Firecrest CC Tubular Firecrest CC Firecrest TU B 404 Firecrest CC Firecrest TU C 808 Firecrest CC Firecrest TU R1 900 TU Disc NA NA Super-9 CC Disc NA NA C Firecrest CC Super-9 TU Disc NA NA Clincher Clincher Firestrike CC & TU Firestrike CC & TU Center axis of wheel Rev D Wheels

93 Driver and Wheel Standard - Road Stop surface min 50 mm ^2, rectangular to spline surface Usable depth of thread min 4.5 See detail A 75 Dropout distance 10 sp: sp: ±0.2 Installation space border for drivetrain Spoke clearance min. 7 at 75 mm offset from wheel center Detail A : scale 5 : 1 Max recess 1 Transition start max Rev D Wheels

94 Driver and Wheel Standard - Road Continued Detail B : scale 10 : 1 See detail B Max R0.3 Max R1 Max R0.4 Ø Max R Rev D Wheels

95 Rear Maxle Frame Specification Maxle Ultimate Hub OLD (mm) A (mm) Axle length B (mm) Thread length C Thread pitch 20 M12x1.75-6g Lever in Closed Position A C Ø24 B mm min full thread 7.62 Lever in Open Position Notes: 1 Drawing is not to scale Thread form per ISO-965 Customer is responsible for ensuring hub, frame, and axle compatibilty. Head translates along the Maxle axis approximately 1.46 mm when lever is moved from open to closed Rev D Wheels

96 Rear Maxle Frame Specification Frame dropouts with axle installed A HUB OLD ±2 2 C 0.14M A Ø24 min Ø Chamfer Ø24 Chamfer 16 A A Rev D Wheels

97 Front Maxle Fork Specification Hub OLD (mm) A (mm) Axle length B (mm) Thread length C Thread pitch D (mm) Axle diameter Maxle Ultimate 15 9 M15x1.5-6h Maxle Ultimate M12x1.5-6h Lever in Closed Position A D C Ø24 B max thread trace Lever in Open Position Notes: 1 Drawing is not to scale Thread form per ISO-965 Customer is responsible for ensuring hub, frame, and axle compatibilty. Head translates along the Maxle axis approximately 1.46 mm when lever is moved from open to closed Rev D Wheels

98 Front Maxle Fork Specification Hub OLD (mm) A (mm) Axle length B (mm) Thread length C Thread pitch D Axle diameter Maxle Ultimate 15 9 M15x1.5-6h Maxle Ultimate M12x1.5-6h D C ØD±0.03 ØD±0.03 Ø24 min flat surface and thru axle head clearance B ±2 10 D Rev D Wheels

99 GEN Rev D 2016 SRAM LLC