HOPPER BINS - BOTTOM MODELS ASSEMBLY MANUAL

Size: px
Start display at page:

Download "HOPPER BINS - BOTTOM MODELS ASSEMBLY MANUAL"

Transcription

1 HOPPER BINS - BOTTOM MODELS ASSEMBLY MANUAL ORIGINAL INSTRUCTIONS Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep manual for future reference. Part Number: BNH R7 Revised: 6/1/14

2 This product has been designed and constructed according to general engineering standards a. Other local regulations may apply and must be followed by the operator. We strongly recommend that all personnel associated with this equipment be trained in the correct operational and safety procedures required for this product. Periodic reviews of this manual with all employees should be standard practice. For your convenience, we include this sign-off sheet so you can record your periodic reviews. Date Employee Signature Employer Signature a. Standards include organizations such as the American Society of Agricultural and Biological Engineers, American National Standards Institute, Canadian Standards Association, International Organization for Standardization, EN Standards, and/or others.

3 TWISTER - HOPPER BINS - BOTTOM MODELS TABLE OF CONTENTS 1. Introduction Safety General Safety Information Assembly Safety Safety Decals Decal Installation Safety Decal Locations Assembly Pre-Assembly Site Selection Sealing Instructions for all Bolted Hopper Bottoms , 19, & 22 Hopper Foundation Steel Foundation Concrete Foundation Hopper Bottom Assembly Assembly Methods (14 ) Bin Preparation Bin Ring External Stiffener Brackets Hopper Columns and Foot Pads Hopper Cone Wind Braces Hopper Throat and Slide Gate Round Tube Aeration Assembly Instructions Rocket Aeration Assembly Instructions & 22 Hopper Bottom Assembly Assembly Methods (19-22 ) Hopper Columns Bin Ring Hopper Cone, Wind Braces, and Throat Leg Braces Slide Gate and Crank Hopper Topper and Patch & 22 Hopper Aeration Assembly Instructions Other Components Manhole Installation Sidewall Ladder Limited Warranty BNH R7 3

4 TWISTER - HOPPER BINS - BOTTOM MODELS 4 BNH R7

5 TWISTER - HOPPER BINS - BOTTOM MODELS 1. Introduction 1. INTRODUCTION Thank you for purchasing a Twister hopper bottom. You will be working with equipment designed to complement and improve your farming operation. Before using this hopper bottom, please read this manual and familiarize yourself with the various features of the equipment and the necessary precautions for efficient and safe operation. In addition, anyone using this hopper bottom is required to be familiar with all safety precautions. A sign-off form is supplied on the inside front cover to record your safety reviews. Keep this manual handy for frequent reference and to review with new personnel. Call your local distributor or dealer if you need assistance or additional information. BNH R7 5

6 1. INTRODUCTION TWISTER - HOPPER BINS - BOTTOM MODELS 6 BNH R7

7 TWISTER - HOPPER BINS - BOTTOM 2. SAFETY MODELS 2.1. GENERAL SAFETY INFORMATION 2. Safety 2.1. GENERAL SAFETY INFORMATION The Safety Alert symbol identifies important safety messages on the product and in the manual. When you see this symbol, be alert to the possibility of personal injury or death. Follow the instructions in the safety messages. Why is SAFETY important? Accidents disable and kill. Accidents cost. Accidents can be avoided. SIGNAL WORDS: Note the use of the signal words DANGER, WARNING, CAUTION, and NOTICE with the safety messages. The appropriate signal word for each message has been selected using the definitions below as a guideline. DANGER Indicates an imminently hazardous situation that, if not avoided, will result in serious injury or death. WARNING Indicates a hazardous situation that, if not avoided, could result in serious injury or death. CAUTION Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury. NOTICE Indicates a potentially hazardous situation that, if not avoided, may result in property damage. BNH R7 7

8 2. SAFETY TWISTER - HOPPER BINS - BOTTOM 2.2. ASSEMBLY SAFETY MODELS YOU are responsible for the SAFE use and maintenance of your equipment. YOU must ensure that you and anyone else who is going to work around the equipment understands all procedures and related SAFETY information contained in this manual. Remember, YOU are the key to safety. Good safety practices not only protect you, but also the people around you. Make these practices a working part of your safety program. Important: Below are general instructions that apply to all safety practices. Any instructions specific to a certain safety practice (e.g., Operational Safety), can be found in the appropriate section. Always read the complete instructional sections and not just these safety summaries before doing anything with the equipment. It is the equipment owner, operator, and maintenance personnel's responsibility to read and understand ALL safety instructions, safety decals, and manuals and follow them when assembling, operating, or maintaining the equipment. All accidents can be avoided. Equipment owners must give instructions and review the information initially and annually with all personnel before allowing them to operate this product. Untrained users/operators expose themselves and bystanders to possible serious injury or death. Use this equipment for its intended purposes only. Do not modify the equipment in any way without written permission from the manufacturer. Unauthorized modification may impair the function and/or safety, and could affect the life of the equipment. Any unauthorized modification of the equipment voids the warranty. Do not allow any unauthorized person in the work area ASSEMBLY SAFETY Have 2 people handle the heavy, bulky components. Stay away from overhead power lines and other obstructions during assembly. Contact with power lines can cause electrocution. Tighten all fasteners to their specified torque before using the equipment. Do not work in high winds. Edges of bin sheets, roof sheets, and other components may be sharp and can cut. Handle with care and wear protective gloves and clothing when handling SAFETY DECALS Keep safety decals clean and legible at all times. Replace safety decals that are missing or have become illegible. See decal location figures that follow. Replaced parts must display the same decal(s) as the original part. Safety decals are available from your distributor, dealer, or factory. 8 BNH R7

9 TWISTER - HOPPER BINS - BOTTOM 2. SAFETY MODELS 2.3. SAFETY DECALS DECAL INSTALLATION 1. Decal area must be clean and dry, with a temperature above 50 F (10 C). 2. Decide on the exact position before you remove the backing paper. 3. Align the decal over the specified area and carefully press the small portion with the exposed sticky backing in place. 4. Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place. 5. Small air pockets can be pierced with a pin and smoothed out using the sign backing paper SAFETY DECAL LOCATIONS Replicas of the safety decals that are attached to the equipment are shown in the figure(s) that follow. Proper safety procedures require that you familiarize yourself with the various safety decals and the areas or particular functions that the decals apply to, as well as the safety precautions that must be taken to avoid serious injury, death, or damage. BNH R7 9

10 2. SAFETY TWISTER - HOPPER BINS - BOTTOM 2.3. SAFETY DECALS MODELS Figure 2.1 Safety Decal Locations 10 BNH R7

11 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS 3.1. PRE-ASSEMBLY 3. Assembly WARNING Before continuing, ensure you have read and understand the relevant information in the safety section. Safety information is provided to help prevent serious injury, death, or property damage PRE-ASSEMBLY SITE SELECTION The selection of the site is the most important step in erecting a Twister hopper bin. Choose a firm, level, well-drained site preferably on a small hill or rise so that snow and water cannot collect near the grain bin. The soil should have a bearing capacity of at least 3,000 lb/ft 2 Check for bearing capacity if there is any doubt at all about its adequacy. Top soil is not adequate for the support of a hopper bin and must be removed prior to the construction of the bin. The foundation does not extend below the frost line in some market areas and may be subject to frost movement with some soil conditions. If in doubt about the site location, hire a professional engineer who is familiar with local conditions. Table 3.1 Bearing Capacity Material Capacity Dry consolidated clay 10,000 Compacted coarse to fine sand 8,000 Sandy clay 5,000 6,000 Silt 3,000 4,000 Stiff clay 3,000 Soft clay <2,000 Some materials that seem adequate at one time of year may become unstable later. Dry clay, for example, may lose practically all its strength if it is allowed to become saturated with water. In general, a compacted gravel base is the only safe preparation for a foundation. Hopper bins must not be located next to high buildings that may cause snow to build-up unevenly on the bin roof or cause uneven wind pressure. Both can result in bin damage. BNH R7 11

12 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM 3.1. PRE-ASSEMBLY MODELS SEALING INSTRUCTIONS FOR ALL BOLTED HOPPER BOTTOMS Follow the instructions below to protect the hopper against water entry and grain leakage. Use the 3/16 butyl caulking roll and the grey MultiFlex caulking tubes provided. If additional sealing is desired, additional tubes of MultiFlex are available from your Twister dealer or you may purchase another thermoplastic sealent. It is important to use a thermoplastic sealant for a proper seal. Do not use silicone. 1. Apply 2 rows of 3/16 butyl caulking to the throat (one row on each side of the bolt holes) before fastening the throat to the cone, as shown in Figure 3.1. See Hopper Throat and Slide Gate on page 30 for assembly instructions. CONE CAULKING ROWS (3/16 BUTYL) THROAT Figure 3.1 Hopper Throat 2. Apply a 1/4 bead of grey MultiFlex caulking around the hopper ring and bin wall interface. See Figure 3.2. BIN WALL CAULKING (1/4 BEAD) RING BEAM Figure 3.2 Hopper Ring 12 BNH R7

13 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS 3.1. PRE-ASSEMBLY 3. Apply 3/16 butyl caulking to the ring beam and cone sheet interface shown in Figure 3.3. See Hopper Cone on page 27 for cone assembly instructions. RING BEAM CAULKING (3/16 BUTYL) CONE SHEET Note: Figure 3.3 Hopper Cone 4. In areas with heavy rainfall, you may wish to seal between cone sheets, as shown in Figure 3.4. We recommend using 3/16 butyl caulking or thermoplastic sealent. See Hopper Cone on page 27 for cone assembly instructions. Sealant is not provided for this application. CAULKING (3/16 BUTYL) CONE SHEETS Figure 3.4 Cone Sheets BNH R7 13

14 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM , 19, & 22 HOPPER FOUNDATION MODELS , 19, & 22 HOPPER FOUNDATION STEEL FOUNDATION All Twister hopper combos may be supported using our steel, bolt-together foundations. However, it is very important that these foundations be supported with an adequate, compacted, gravel base to ensure that they will not shift and cause the structure to fail. Twister steel foundations are for use with hopper bottoms manufactured by Twister and are not warranted for use with any other make of hopper. The following precautions must be taken: Proper site preparation is critical! Topsoil will not provide adequate support for the foundation. Remove all loose, organic, or wet soil from the area around the foundation as shown in Figure 3.5. Steel foundations must be placed on a layer of gravel of sufficient depth and compaction, and must remain level to within ± 1/2 after loading. See Figure 3.5 and Tables 3.2 and 3.3 for the appropriate base for your hopper. NOTICE Compacted gravel base must remain level. Any out-of-level condition on the foundation will cause deformation or failure of the bin sidewalls and hopper components. The foundation must make contact with the gravel base all around the perimeter of the foundation. Gaps between the gravel and the foundation are not permissible. The foundation and hopper must be anchored to prevent the structure from overturning in the wind when empty. The hopper should be placed on high ground in a well-drained location. Center the assembled skid over the desired location of the hopper. H H H Figure 3.5 Steel Foundations Assembly 14 BNH R7

15 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS , 19, & 22 HOPPER FOUNDATION Table 3.2 Gravel Depth and Quantity Number of Rings Bin Diameter Gravel Depth (in) Qty (yd 3 ) Gravel Depth (in) Qty (yd 3 ) Gravel Depth (in) Table 3.3 Bearing Capacity Required for Compacted Gravel, lb/ft 2 Number of Rings Bin Diameter Qty (yd 3 ) Gravel Depth (in) Qty (yd 3 ) Gravel Depth (in) Qty (yd 3 ) / Steel Foundation Materials Item Description Qty 1 Skid Section 3 2 1/2-13 x 1-1/2 Flange Hex Bolt /2-13 Flange Nut /2 Washer 24 Figure Steel Foundation BNH R7 15

16 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM , 19, & 22 HOPPER FOUNDATION MODELS / Steel Foundation Materials Item Description Qty 1 Skid Section 6 2 1/2-13 x 1-1/2 Flange Hex Bolt /2-13 Flange Nut /8-11 x 2 Flange Hex Bolt /8-11 Flange Nut /2 Washer 52 Figure Steel Foundation 16 BNH R7

17 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS , 19, & 22 HOPPER FOUNDATION / Steel Foundation Materials Item Description Qty 1 Skid Section 7 2 1/2-13 x 1-1/2 Flange Hex Bolt /2-13 Flange Nut /8-11 x 2 Flange Hex Bolt /8-11 Flange Nut /2 Washer 60 Figure Steel Foundation BNH R7 17

18 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM , 19, & 22 HOPPER FOUNDATION MODELS CONCRETE FOUNDATION Concrete foundations will provide the safest support for any hopper bin. It is highly recommended that hopper bins greater than 5 tiers high (Models 14-5, 16-5, 19-5, 22-5) and all hoppers in permanent locations be supported with concrete foundations. When placing a concrete foundation, the following precautions must be taken: Important: Choose a well drained location with a minimum soil bearing capacity of 3,000 lb/ft 2. If soil bearing capacity is not known, consult a local engineering professional. Remove all topsoil and construct a concrete pad for the appropriate hopper size (Figure ). The perimeter beam and slab must rest on coarse gravel compacted to 3700 lb/ft 2 and should rise above the surrounding soil. Use 3,000 lb/ft 2 in concrete and reinforcement as shown. The hopper bin must be anchored to the foundation to prevent the structure from overturning in the wind when empty. If you have purchased a concrete form from Twister and will reuse the form, install the leveling brackets on the exterior of the form. Install the bolts on the inside and the nuts on the outside of the form for easy removal. 18 BNH R7

19 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS , 19, & 22 HOPPER FOUNDATION 19-1/4 9-5/8 79-9/16 R92 6 X 6 WIRE MESH R80 R M TIE BARS POSITION UNDER COLUMNS M REBAR TOP AND BOTTOM EQUAL SPACES 3 1 MAX CROWN FOR DRAINAGE LAYER WIRE MESH 6 X 6 COMPACTED COARSE GRAVEL Concrete Foundation Description Coarse Gravel 10M Rebar x 20 10M Rebar x 5 Qty 3.7 yd / 3.4 m 13 pcs 12 pcs 6 x 6 Wire Mesh 162 ft psi Concrete 6.0 yd / 5.5 m Anchor Requirements: Shear = 1300 lb/anchor Uplift = 10,500 lb/anchor Figure Concrete Foundation BNH R7 19

20 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM , 19, & 22 HOPPER FOUNDATION MODELS 9/16 13/ / X 6 WIRE MESH R98 R116 R M TIE BARS 1-LAYER WIRE MESH 6 X M REBAR 4 EQUALLY SPACED 3 1 MAX CROWN FOR DRAINAGE 24 6 COMPACTED COARSE GRAVEL 8-15 M REBAR EQUALLY SPACED Concrete Foundation Description Coarse Gravel 15M Rebar x 20 10M Rebar x 9 Qty 7.8 yd / 7.1 m 30 pcs 24 pcs 6 x 6 Wire Mesh 370 ft psi Concrete 18.5 yd / 16.9 m Anchor Requirements: Shear = 1500 lb/anchor Uplift = 10,400 lb/anchor Figure Concrete Foundation 20 BNH R7

21 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY 9/16 13/ /16 9 R155 6 X 6 WIRE MESH R115 R / M TIE BARS POSITION UNDER COLUMNS M REBAR TOP AND BOTTOM EQUALLY SPACED 3 1 MAX CROWN FOR DRAINAGE LAYER WIRE MESH 6 X COMPACTED COARSE GRAVEL Concrete Foundation Description Qty Coarse Gravel 15M Rebar x 20 10M Rebar x yd / 19.1 m 47 pcs 14 pcs 6 x 6 Wire Mesh 450 ft psi Concrete 25 yd / 22.9 m Anchor Requirements: Shear = 1660 lb/anchor Uplift = 10,400 lb/anchor Figure Concrete Foundation HOPPER BOTTOM ASSEMBLY This hopper bottom is meant to be used under galvanized steel Twister bins that have a 520 circumference or 13 9 diameter when measured to the inside of the corrugation of the bin wall. This will include bins manufactured by Twister as well as some other manufacturers bins commonly referred to as 14 bins. This hopper is designed for use on a new Twister bin. If using the hopper on an older Twister flat bottom bin, call Twister for advice concerning additional stiffening that may be required. BNH R7 21

22 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM HOPPER BOTTOM ASSEMBLY MODELS Ensure that the hopper will fit on another manufacturer s bin before beginning any assembly work. Call manufacturer if you are unsure. Twister has no control over the manufacture and design of bins made by other companies and does not accept liability for any property loss, injury, or death that may result form the use of such bins. NOTICE Many bins used in flat bottom applications are not adequately stiffened for use on hoppers. Failure to ensure that the design is sound and safe may result in damage to bin and/or personal injury. Note: Refer to Figures 3.12, and , and for part identification, hardware usage, and layout Figure Hopper Exploded View 22 BNH R7

23 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY 14 Hopper Bill of Materials Item Description Qty 1 Ring Beam 12 2 Splice Bracket 12 3 Cone Section 9 4 Manhole Cone Section 1 5 Aeration Inlet Cone Section 1 6 Rocket Inlet Cone Section 1 7 Top Leg Bracket (6L, 6R) 12 8 Leg 12 9 Foot Pad 6 10 Leg Brace 6 11 Wind Brace Bracket 6 12 Wind Brace 6 13 Throat 1 14 Slide Gate Assembly 1 15 Crank Guide 1 16 Crank Handle 1 17 Aeration Inlet Cover Plate 1 18 Rocket Inlet Cover Plate 1 19 Internal Stiffener Bracket 9 20 Ladder (Not shown, see ladder assembly) 1 21 Skid Section 6 BNH R7 23

24 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM HOPPER BOTTOM ASSEMBLY MODELS ASSEMBLY METHODS (14 ) There are two common methods used to assemble 14 hopper bottoms. The first method is to build the hopper bottom onto a hopper top that is supported by a bin crane, beginning by adding segments of the ring beam and working with the sequence presented in this manual until the full hopper bin is complete. The second method is to build the hopper bottom fully, using whatever sequence is preferred by the assembler as long as it follows the principles set out in this manual. To assemble the full hopper bin, use a bin crane to lift a hopper top onto the hopper bottom. For both methods, it is important to ensure that specific bolts on the hopper top are loose before the ring beam and the hopper top are joined together. Before joining hopper top to the hopper bottom ring beam, it is important to ensure that: All bottom-tier hopper-top stiffener bolts are sufficiently loose (nuts placed fully on bolts, but not tightened). All bottom-tier hopper-top vertical seam bolts are sufficiently loose (nuts placed fully on bolts, but not tightened). These stiffener and vertical seam bolts can be fully tightened only after the hopper top is fully connected to the ring beam of the hopper bottom with 3/8 x 1-1/8 bin bolts inserted from outside the hopper top. WARNING When lifting or supporting a hopper top with a crane, always ensure that the crane is rated for the load (including weight of hopper bottom if required) and has sufficient reach height and reach angle to lift, support, and place the hopper top BIN PREPARATION Before placing the bin on the hopper, the bin sidewall ladder must be positioned on the ring beam for the hopper ladder to fit properly. See Sidewall Ladder on page 45. NOTICE Stiffeners vary in thickness (gauge). If the stiffeners are improperly installed, the bin could collapse once filled with grain. 24 BNH R7

25 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY BIN RING Note: 1. Raise the bin to a comfortable height and bolt the ring beams to the bin wall. Make sure the name sheet is centered over the center of a ring beam; this will allow the hopper ladder to line up between the two A-frame columns. 2. Bolt the top leg brackets to the splice brackets as shown in Figure The top leg brackets come in right and left parts. Plan ahead to get the name sheet centered between two columns as shown in the Sheet and Stiffener Layout in the Hopper Top manual. Figure 3.13 shows how the left and right top leg bracket pairs must be oriented in relation to each other. 7 LEFT BRACKET Figure 3.13 Left and Right Leg Bracket Orientation RIGHT BRACKET 3. Apply a strip of 3/16 caulking to the back of the splice brackets as shown in Figure Bolt the splice brackets to the ring beams as shown. 4. Double check the orientation of the top leg brackets /16 CAULKING Figure 3.14 Splice Bracket Assembly 5. When all the ring beams are fitted to the bin wall and the splice brackets are fitted to the ring beams, tighten the bolts in the bin wall. When this is done, tighten the bolts in the ring. BNH R7 25

26 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM HOPPER BOTTOM ASSEMBLY MODELS EXTERNAL STIFFENER BRACKETS STIFFENER DRILL 9/16 HOLE THROUGH RING BEAM AND INSTALL 1/2 GR8 BOLT. 3/8 X 3/4 GR8 BIN BOLTS BOTTOM BRACE ORIGINAL STIFFENER BOLT 1/2 GR8 BOLT IDENTIFICATION SIDE VIEW RING BEAM BOLT RING BEAM Figure 3.15 External Stiffener Bracket 26 BNH R7

27 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY HOPPER COLUMNS AND FOOT PADS 1. Raise the bin and bolt the legs to the top leg brackets; refer to Figure When all the legs are bolted at the top, the footpads can be bolted to the bottom of the legs. 3. Finally, bolt on the leg braces to finish the columns Figure 3.16 Column and Foot Pad Assembly HOPPER CONE Included in this hopper cone package are nine cone sections, one manhole cone section, and two cone sections designed to accommodate Round Tube and Rocket aeration system. Relative locations of the manhole, Rocket and Round Tube aeration inlet cone sections are dependent on your site plan no matter what type of aeration system you are planning to use. Figure 3.17 shows an example layout of the hopper cone sections. MANHOLE CONE ROCKET AERATION INLET CONE ROUND TUBE AERATION INLET CONE Figure 3.17 Example Layout of Hopper Cone Sections BNH R7 27

28 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM HOPPER BOTTOM ASSEMBLY MODELS To assemble the hopper cone: Note: Note: 1. Based on your site plan and your preferred locations of the fan and unload system, determine the position of the Rocket or Round Tube aeration inlet and manhole cone sections; and then, plan the cone assembly accordingly. See Sealing Instructions for all Bolted Hopper Bottoms on page 12 for cone sealing instructions. Leave the manhole or Rocket/Round Tube aeration inlet cone section for last. This will make inserting the last bolts much easier. 2. Offset the cone sections 1 bolthole clockwise relative to the ring beams (Figure 3.18). One side of the cone sections is bent in towards the center of the cone. This side should be to the right, as viewed from the center of the cone, and under the next section Note: Figure 3.18 Cone Section Assembly 3. Install the remaining cone sections, including Rocket and Round Tube cone sections, following step 2. If you are going to use Rocket aeration system, install the Round Tube inlet cover plate to block-off Round Tube inlet (Figure 3.19). If you are going to use Round Tube aeration system, install the Rocket inlet cover plate to block-off Rocket aeration inlet (Figure 3.20). If aeration system is not desired, cover both aeration inlets with their respective plates. The bin that is to be assembled on the top can be clocked in any orientation independent of the bottom cone. 28 BNH R7

29 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY NOTE: ROCKET SHOWN IS FOR ILLUSTRATION PURPOSES ONLY, ACTUAL ROCKET INSTALLED MAY VARY. Figure 3.19 Example of Hopper Cone with Rocket Aeration System Figure 3.20 Example of Hopper Cone with Round Tube Aeration System BNH R7 29

30 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM HOPPER BOTTOM ASSEMBLY MODELS WIND BRACES 1. Bolt the wind brace to the cone sections as shown in the exploded view to support the cone as it is assembled (Figure 3.12). 2. The wind brace bracket has slotted holes. Once the cone is completely assembled, move the bracket up or down in the holes to plumb the columns. When the correct position of the bracket has been determined, remove the wind brace from the cone end and tighten the wind brace bracket bolts. Replace the wind brace. 3. There are holes for the wind brace bracket in every sheet. Insert bolts in the holes where no wind brace exists Figure 3.21 Wind Brace Assembly HOPPER THROAT AND SLIDE GATE 1. Install the throat on the outside of the cone as shown Figure See Sealing Instructions for all Bolted Hopper Bottoms on page 12 for hopper throat sealing instructions. 2. Install the slide gate assembly such that its side is parallel to any hopper leg desired (Figure 3.12). The slide gate ring fits inside the throat. 30 BNH R7

31 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY Figure 3.22 Hopper Throat Assembly 3. Install the crank and handle assembly and the crank guide (Figure 3.12). 4. Install the manhole assembly, and if aeration is not desired, install the inlet cover ROUND TUBE AERATION ASSEMBLY INSTRUCTIONS Refer to Figure for the illustrations of the assembly, and Table 3.4 for the quantity of each component used. 1. Place support brackets and duct support angles in the hopper. Align the center hole of the support bracket with the bottom hole of the fan tube. Make sure the end holes of the support bracket line up with the thirteenth (13) and fourteenth (14) holes from the bottom of the cone, and bolt them together. Do not tighten the bolts. 2. Bolt the remaining support bracket to the cone section opposite the inlet cone section as shown in Figure The brackets fit on the thirteenth (13) and fourteenth (14) holes from the bottom of the cone. 3. Bolt the duct support angles to the support brackets. 4. Place the aeration duct inside the hopper cone. Slide aeration duct (capped end first) into fan tube. Push into fan tube until aeration duct is 25-5/8 into the fan tube. The solid edge at the end of the aeration duct should be centered to the holes in the fan tube.tighten all bolts. See Figure 3.24 and Secure the aeration duct to the fan tube with the screws provided. Secure the hold-down straps. 6. Use spray foam as desired to prevent any grain leakage. BNH R7 31

32 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM HOPPER BOTTOM ASSEMBLY MODELS Figure 3.23 Bolting the Support Bracket to the Hopper Cone Important: Ensure aeration duct is 25-5/8 inside the fan tube. This is critical to proper positioning of the tube in the bin (Figure 3.24). AERATION DUCT FAN TUBE Figure 3.24 Position of Aeration Duct in Fan Tube 32 BNH R7

33 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY Figure Hopper Aeration Assembly Table Hopper Aeration Materials Item Part No. Description Qty 1 BRA Fan Tube 1 2 GGR-8573 Aeration Duct Hold Down Strap 3 5 BXA Duct Support Angle 2 6 BXA Support Bracket /8 x 3/4 Bin Bolt /8 Flange Nut /4 x 3/4 Sheet Metal Screw BSPRAY Spray Foam /16 Caulking Roll /2 x 1-1/2 Flange Hex Bolt /8 Washer /2 Flange Nut /2 Washer ROCKET AERATION ASSEMBLY INSTRUCTIONS Refer to the Rocket Installation Manual for the assembly instructions. BNH R7 33

34 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM HOPPER BOTTOM ASSEMBLY MODELS & 22 HOPPER BOTTOM ASSEMBLY The 19 hopper bottom is meant to be used under galvanized steel Twister bins that are 720 in circumference or 19 in diameter, and the 22 hopper bottom is meant to be used under galvanized steel bins that are 838 in circumference or 22 3 in diameter. (Diameter is measured to the inside corrugation of the bin wall.) This will include bins manufactured by Twister as well as some other manufacturer s bins commonly referred to as 19 or 22 bins. This hopper is designed for use on a new Twister bin. If using the hopper on an older Twister flat bottom bin, call Twister for advice concerning additional stiffening that may be required. Ensure that the hopper will fit on another manufacturer s bin before beginning any assembly work. Call the manufacturer if you are unsure. Important: Stiffeners should be placed no further than 5 apart if the bin is to be used on a hopper. NOTICE Many bins used in flat bottom applications are not adequately stiffened for use on hoppers. Twister does not assume responsibility for any failure or damage caused by the use of products built by other manufacturers. For Size See Figure: See Tables: 19 Hopper Bottom Figure 3.26 Table 3.5, Hopper Bottom Figure 3.27 Table 3.6, BNH R7

35 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY Figure Hopper Exploded View Table Hopper Bill of Materials Item Description Qty 1 Ring Beam 12 2 Square Steel Patch 12 3 Top Cone Section 12 4 Bottom Cone Section 10 5 Bottom Cone Section with manhole cutout 1 6 Bottom Cone Section with aeration hole and cover plate 1 7 Leg 12 8 Shims 48 9 Leg Brace - Left, Right Windbrace Brackets Wind Brace Throat 1 13 Slide Gate Assembly 1 14 Crank Guide 1 15 Crank Handle 1 16 Ladder (not shown, see ladder assembly) 1 17 Skid Section 6 BNH R7 35

36 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM HOPPER BOTTOM ASSEMBLY MODELS Figure Hopper Exploded View Table Hopper Parts Item Description Qty 1 Ring Beam 14 2 Square Steel Patch 14 3 Top Cone Section 14 4 Bottom Cone Section 12 5 Bottom Cone Section with manhole cutout 1 6 Bottom Cone Section with aeration hole and cover plate 1 7 Leg 14 8 Shims 48 9 Leg Brace - Left, Right Windbrace Brackets Wind Brace Throat 1 13 Slide Gate Assembly 1 14 Crank Guide 1 15 Crank Handle 1 16 Ladder (not shown, see ladder assembly) 1 17 Skid Section 7 36 BNH R7

37 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY ASSEMBLY METHODS (19-22 ) The standard method used to assemble 19 and 22 hopper bottoms is to build the hopper bottom fully, according to the sequence outlined in this manual. To assemble the full hopper bin, use a bin crane to lift the hopper top onto the hopper bottom. Other methods or variations are acceptable as long as they follow the general principles of assembly outlined in this manual. Regardless of what method is used, it is important to ensure that specific bolts on the hopper top are loose before the hopper bottom ring beam and the hopper top are joined together. Before joining hopper top to the hopper bottom ring beam, it is important to ensure that: All bottom-tier hopper-top stiffener bolts are sufficiently loose (nuts placed fully on bolts, but not tightened). All bottom-tier hopper-top vertical seam bolts are sufficiently loose (nuts placed fully on bolts, but not tightened). These stiffener and vertical seam bolts can be fully tightened only after the hopper top is fully connected to the ring beam of the hopper bottom with 3/8 x 1-1/8 bin bolts inserted from outside the hopper top. WARNING When lifting or supporting a hopper top with a crane, always ensure that the crane is rated for the load (including weight of hopper bottom if required) and has sufficient reach height and reach angle to lift, support, and place the hopper top HOPPER COLUMNS Note: 1. Steel Foundations Only: Secure the square columns to the skid in the locations provided with two 1/2 x 1-1/2 hexagon head bolts through the base plate. Washers will be required as the holes are oversized. Refer to Table 3.5 for quantities. Ensure the brackets on the columns are facing the centre of the skid. 2. Concrete Foundations Only: To ensure columns are positioned correctly, construct the jig shown in Figure The single hole is placed in the center of the foundation and the first pair of holes on the outside will be the location of the column holes. 3. Concrete Foundations Only: Rotate the jig about the center to get the spacing shown in the column locations figure. BNH R7 37

38 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM HOPPER BOTTOM ASSEMBLY MODELS 135-3/8 (22 ) 115-7/8 (19 ) 3-13/32 CENTRE POINT OF FOUNDATION 1 DIAM 5PL 6-13/16 Figure 3.28 Column Positioning Jig BIN RING The ring comes in sections each section will span between two legs. For Size See Figure: See Tables: 19 Hopper Bottom Figure 3.26 Table 3.5, Hopper Bottom Figure 3.27 Table 3.6, Lift the ring sections into place and bolt the bottom of the ring to the bracket at the top of the leg using 1/2 x 1-1/2 hexagon head bolts. Shim to fit as shown in Figure Each ring section has a flange at each end of the section. 1 1/4 X 5 12GA. SHIMS ARE PROVIDED TO PLACE INSIDE AGAINST THE LEG BETWEEN THE BEAM AND BRACKET. DO NOT FORCE SHIMS INTO PLACE. ANY GAP LESS THAN 12GA. CAN BE CLOSED BY TIGHTENING THE BOLT. SHIM TO FIT AS SHOWN. Figure 3.29 Shim Positioning 2. Bolt the ring sections together through the flange. Minimize the gap between ring sections and bolt the ring section to the capitals with 1/2 x 1 hexagon head bolts. 38 BNH R7

39 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY HOPPER CONE, WIND BRACES, AND THROAT For Size See Figure: See Tables: 19 Hopper Bottom Figure 3.26 Table 3.5, Hopper Bottom Figure 3.27 Table 3.6, 3.7 Note: 1. Fasten the top cone sections to the ring and to each other using just enough 1/2 x 3/4 flat head bolts to hold them in place. 2. Bolt the bottom cone sections to the inside of the top cone sections using just enough bolts to hold them in place. 3. Use the wind brace to keep the cone sections from bending. The wind brace is bolted to the leg above the stop provided using u-bolts, to the seam of the cone at the sixth and seventh hole from the bottom for the 19 bin, and where the spacing between holes is 4 for the 22 bin. 4. Once the entire cone is assembled, the rest of the bolts can be placed. Often simply pushing up on the seam will bring the bolt holes into alignment. 5. When the cone is completed, the throat (item #10) can be bolted to the outside of the cone with 1/2 x 1 hexagon head bolts LEG BRACES For Size See Figure: See Tables: 19 Hopper Bottom Figure 3.26 Table 3.5, Hopper Bottom Figure 3.27 Table 3.6, Fasten leg braces to the inside of the ring beam with two 3/8 x 1-1/8 bin bolts and to the outside of the column with one 1/2 x 1 bolt supplied in the leg. 2. Use a 1/2 washer at the brace-to-column connection to cover the slotted hole in the leg brace. BNH R7 39

40 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM HOPPER BOTTOM ASSEMBLY MODELS SLIDE GATE AND CRANK For Size See Figure: See Tables: 19 Hopper Bottom Figure 3.26 Table 3.5, Hopper Bottom Figure 3.27 Table 3.6, 3.7 Note: Note: 1. The slide gate assembly fits inside the throat and is fastened with 3/8 x 1-3/4 bin bolts. 2. The crank guide is fastened to the outside of the column with a u-bolt. Before tightening the slide gate in place, make sure that the crank guide, crank, and slide gate are in line. Do not assemble the ladder until the bin is on the hopper. 3. Position the ladder under the bin ladder. The ladder is bolted to brackets that are bolted to the inside of the column with u-bolts HOPPER TOPPER AND PATCH 1. Secure the ring beams together by fastening a square steel patch on each seam between two adjoining ring beams. See Figure 3.30 and Table 3.7. RING BEAM SQUARE STEEL PATCH RING BEAM Figure 3.30 Installing Square Steel Patch 2. Place the hopper topper on the hopper with the stiffeners directly over the columns of the hopper. 3. Bolt the hopper topper to the hopper at the stiffener locations. At this point, do not forget to include the hopper stiffener bin braces for the outside of the ring (Figure 3.31). See Figure 3.31 for hardware and use 3/8 x 3/4 bin bolts to connect the rest of the hopper topper to the hopper. 40 BNH R7

41 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY 3/8 X 1-1/8 BIN BOLT AND NUT HOPPER STIFFENER BIN BRACE 1/2 X 1-1/4 BIN BOLT AND NUT HOPPER STIFFENER BIN BRACE 1/2 X 1-1/4 BIN BOLT AND NUT 22 HOPPER BOTTOM STIFFENER BIN CONNECTION 19 HOPPER BOTTOM STIFFENER BIN CONNECTION Figure 3.31 External Stiffeners Table & 22 Hopper Hardware List - No Aeration, No Skid Description Location Required Qty /2 x 1 Carriage Bolt Cone /2 x 1-1/2 Flange Hex Bolt Ring Beam, Ring Beam to Leg Bracket /2 x 3 Flange Hex Bolt Windbrace Bracket /2 x 4 U-Bolt Windbrace, Ladder Bracket and Crank Guide 13-1/2 x 5 U-Bolt Windbrace and Crank Guide /2 Flange Nut /2 Plate Washer Legbrace to Leg and Windbrace Bracket /8 x 1-1/8 Bin Bolt Legbrace to Ring Beam /8 x 1-3/4 Bin bolt Ladder and Slidegate 6 6 3/8 Flange Nut /4 Self Drilling Screw Square Patch Square Patch As Instructed /16 x 20 Caulking Throat and Manhole 1 Roll 1 Roll Grey MultiFlex Caulking 318 ml Bin and Hopper Connection 2 Tubes 2 Tubes BNH R7 41

42 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM HOPPER BOTTOM ASSEMBLY MODELS & 22 HOPPER AERATION ASSEMBLY INSTRUCTIONS Note: Refer to Figure 3.32 and 3.33 for the illustrations of the assembly, and to Table 3.8 for the quantity of the components used. 1. Assemble five elbows by bolting stands (3) to the elbow pieces (1) as shown in Figure 3.32, using 1/2 x 1 fin bolts (9) and 1/2 flange nuts (6). Install bolts from the inside. 2. Steel covers (1) and elbow pieces (1) use the same parts. After all five elbows have been assembled, install 1/2 x 1 fin bolts (9) in the empty holes on the remaining steel covers where the elbow stand would normally attach, as shown in Figure Note: Holes must be filled to prevent grain from passing through the steel covers (1). STEEL COVER ELBOW INLET 1/2 X 1 FIN BOLTS Note: Figure 3.32 Steel Cover and Elbow Assembly 3. Install inlet (4) over the cutout on the appropriate cone sheet; see Step A in Figure Apply 3/8 caulking (10) to the inlet flange and bolt the inlet to the cone using 1/2 x 1 fin bolts (9). Do not install the inlet (4) on the manhole sheet. 4. Install an elbow (1+3) on every second sheet of the cone; see Step B in Figure Install using 1/2 x 1 fin bolts (9) in the empty holes on every second cone sheet, where no elbow exists; see Step C in Figure Center louvered duct (2) across span between elbows (1+3), seating it firmly in the elbows at either end. Refer to Step D in Figure CAUTION Wear work gloves while handling the louvered duct. The duct has sharp edges that could cause injury. 6. Place steel covers (1) over the ducts (2) and elbows (1+3). Secure using 3/8 x 1-1/8 bin bolts (8). Refer to Step D in Figure BNH R7

43 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS HOPPER BOTTOM ASSEMBLY B. INSTALL ELBOWS ON EVERY 2ND CONE SHEET, MOVING OUTWARD FROM INLET POSITION. D. INSTALL STEEL COVERS OVER ELBOWS AND INLET AS SHOWN. A. INSTALL INLET OVER CUTOUT IN SHEET C. INSTALL BOLTS IN THE EMPTY HOLES ON EVERY 2ND CONE SHEET. Figure 3.33 Twistaire Aeration System Assembly BNH R7 43

44 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM 3.5. OTHER COMPONENTS MODELS Table & 22 Twister Hopper Aeration Parts ITEM PART NO. DESCRIPTION QTY BRA Twistaire Elbows & Covers BNA Twistaire Louvered Duct BRA Twistaire Stand BRA Twistaire Inlet Bolt Flange 1/2 x 1-1/ Nut Flange 1/ Nut Flange 3/ Bolt Bin 3/8 x 1-1/ /2 x 1 Fin Bolt Caulking Roll, 3/16 x FRJ-5233 Exterior Plate OTHER COMPONENTS MANHOLE INSTALLATION 1. Bolt the manhole ring to the hopper using 3/8 x 3/4 bin bolts and the 3/16 roll caulking strip. 2. Fasten the retaining cable to the lid and one of the ring bolts to keep the manhole from sliding to the bottom of the hopper when it is removed. Table 3.9 Hopper Manhole Materials Item Part No. Description Qty 1 BTH-MH1214 Manhole Lid c/w Latches 1 2 BRH-HPMR Manhole Ring 1 3-3/8 x 3/4 Bolts and Nuts 12 4 BZH Retaining Cable /16 Caulking Roll Figure 3.34 Hopper Manhole Assembly 44 BNH R7

45 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS 3.5. OTHER COMPONENTS SIDEWALL LADDER Refer to Figure for the illustrations of the assembly, and Table for the quantity of the components used. 1. Assemble the ladder using 3/8 x 3/4 bolts and flange nuts by attaching the rungs to the hopper stringer. While attaching rungs, secure decal plate as Note: shown in Figure The sidewall ladder is centered on the ring beam section. Bolt the standoffs at the 4th ring beam hole, on each side (See Detail B on Figure 3.36). 2. Ensure 14 (4.2 m) ladder stringer is bolted through bolt holes in standoff. 3. Attach upper braces to hopper ladder and hopper leg braces with 3/8 x 3/4 bolts and flange nuts. 4. Use lower braces and 3/8 x 3/4 bolts to hold the ladder to the steel skid or concrete form. 5. Use 7/16 x 2 bolt to fasten lower braces to skid. Table (4.2m) Hopper Bottom Ladder Parts Item Part No. Description Qty 1 BTL Stringer 2 2 BZL Upper Brace 2 3 BZL Ladder Rung 8 5 BZL Lower Brace /8" x 3/4" Bin Bolt /8" Flange Nut 22 Figure 3.35 Ladder Layout for 14 Hopper Bin BNH R7 45

46 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM 3.5. OTHER COMPONENTS MODELS Figure Hopper Ladder 46 BNH R7

47 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS 3.5. OTHER COMPONENTS Table Hopper Bottom Ladder Parts Item Description Qty 1 Bottom Stringer 2 2 Top Stringer 2 3 Standoff 6 4 Rung 10 5 Hopper Ladder Bracket 3 6 3/8" x 3/4" Bin Bolt /8" Flange Nut " x 4" U-bolt 6 9 1/2" Flange Nut 12 Figure 3.37 Ladder Layout for 19 Hopper Bin BNH R7 47

48 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM 3.5. OTHER COMPONENTS MODELS Figure Hopper Ladder ATTACH DECAL PLATE AS SHOWN Figure Hopper Bin Decal Plate Location 48 BNH R7

49 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS 3.5. OTHER COMPONENTS Table Hopper Bottom Ladder Parts Item Description Qty 1 Bottom Stringer 2 2 Top Stringer ' Hopper Stringer Extension 2 4 Standoff 6 5 Rung 11 6 Hopper Ladder Bracket 3 7 3/8" x 3/4" Bin Bolt /8" Flange Nut " x 5" U-Bolt /2" Flange Nut 12 Figure 3.40 Ladder Layout for 22 Hopper Bin BNH R7 49

50 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM 3.5. OTHER COMPONENTS MODELS Figure Hopper Ladder ATTACH DECAL PLATE AS SHOWN Figure Hopper Bin Decal Plate Location 50 BNH R7

51 TWISTER - HOPPER BINS - BOTTOM 3. ASSEMBLY MODELS 3.5. OTHER COMPONENTS Figure 3.43 Ladder Layouts with Optional Platform BNH R7 51

52 3. ASSEMBLY TWISTER - HOPPER BINS - BOTTOM 3.5. OTHER COMPONENTS MODELS Figure 3.44 Optional Platform 52 BNH R7

53 LIMITED WARRANTY This warranty relates to any new grain bin (the Product ) sold by TWISTER (which is a trading name or division of Ag Growth Industries Partnership, referred to herein as the Seller ) and applies only to the first user of the Product (meaning a purchaser directly from the Seller or from an authorized dealer or distributor of the Product, referred to herein as the Buyer ). This warranty shall only be effective if properly registered with the Seller in accordance with information provided to the Buyer at the time of sale. 1.The Seller warrants to the Buyer that the Product is free from defects in material and workmanship under normal and reasonable use. 2.This warranty applies only to defects in materials and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of the Seller such as lightning, fire, flood, wind, earthquake, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration, improper assembly, improper installation, improper maintenance or improper repair of the Product. 3.This warranty is void if: a) the Product has not been installed and operated in accordance with the instructions provided by the Seller; b) all components of the grain bin system are not original equipment as supplied by the Seller; c) the installation was not done by an authorized dealer or certified representative of the Seller; d) damage to or malfunction or failure of the Product is due to misuse, abuse, negligence of the Buyer, alteration, accident or lack of proper maintenance; or e) the grain bin system is used for the storage of something other than grain or feed. 3.The warranty period for the Product shall be FIVE (5) years from delivery of the Product to the Buyer and initial installation by or for the Buyer. This five year warranty shall only apply to structural elements of the Product. All other parts are covered by a one (1) year warranty period. Painted parts are only warranted for one year against surface rust. In the event that any part of the Product is manufactured and sold to the Seller by a third party vendor, such part is only warranted to the extent of the warranty given by the third party vendor to the Seller. 4.The obligations set forth in this warranty are conditional upon the Buyer promptly notifying the Seller of any defect and, if required, promptly making the Product available for correction. The Seller shall be given reasonable opportunity to investigate all claims and no Product shall be returned to the Seller until after inspection and approval by the Seller and receipt by the Buyer of written shipping instructions from the Seller, with transportation charges prepaid. 5.If a defect is found by the Seller to exist within the applicable warranty period, the Seller will, at its sole option, (a) repair or replace the Product or such part free of charge, FOS the factory of manufacture, or (b) refund to the Buyer, the original purchase price, in lieu or such repair or replacement. Labour costs associated with the replacement or repair of the Product are not covered by the Seller. The Seller shall replace or attempt to repair and return the Product or such part within 4 weeks of receipt of notice of the defect from the Buyer. 6.The total liability of the Seller on any claim, whether in contract, tort or otherwise, arising out of, connected with, or resulting from the manufacture, sale, delivery, repair, replacement or use of the Product or any part thereof shall not exceed the price paid for the Product and the Seller shall not be liable for any special indirect, incidental or consequential damages caused by reason of the installation, modification, use, repair, maintenance or mechanical failure of the Product. 7.The Seller warrants that the use of the Product does not infringe upon the patents, copyrights, trade secrets or other intellectual property rights of others. 8.Notwithstanding anything contained herein to the contrary, the foregoing is the Buyer s sole and exclusive remedy for breach of warranty by the Seller in respect of the Product. The Seller, for itself, its agents, contractors, employees and for any parent or subsidiary of the Seller, expressly disclaims all warranties, either express or implied, written or oral, including implied warranties of merchantability or fitness for a particular purpose and undertakes no obligation with respect to the conformity of the Product except as set out in the purchase agreement, if any. 9.The foregoing warranty is the entire warranty of the Seller. The Seller neither assumes, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning the Product. WARRANTY VOID IF NOT REGISTERED

HOPPER BINS - BOTTOM MODELS ASSEMBLY MANUAL

HOPPER BINS - BOTTOM MODELS ASSEMBLY MANUAL HOPPER BINS - BOTTOM 14-3 22-8 MODELS ASSEMBLY MANUAL ORIGINAL INSTRUCTIONS Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death,

More information

This document to be used with Hurley traditional Davits

This document to be used with Hurley traditional Davits ~ InstructIon Manual ~ This document to be used with Hurley traditional Davits WarnIngs WarnIng - Failure to install, maintain, protect, and operate the system properly can cause malfunction resulting

More information

COMPACT METAL bender 99826

COMPACT METAL bender 99826 COMPACT METAL bender 99826 Set up And Operating Instructions Distributed exclusively by Harbor Freight Tools. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com

More information

HYDRAULIC WINCH FOR AUGERS UP TO WR10 X 71 / W130 X 41 ASSEMBLY & OPERATION MANUAL

HYDRAULIC WINCH FOR AUGERS UP TO WR10 X 71 / W130 X 41 ASSEMBLY & OPERATION MANUAL HYDRAULIC WINCH ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep manual

More information

SHUR-STEP STAIRWAY and Platform

SHUR-STEP STAIRWAY and Platform SHUR-STEP STAIRWAY and Platfm (Patented) Installation Instructions Stiffened and Unstiffened Narrow Wide Crugated Flat-Bottom Grain Bins and Commercial Hopper Bins (above the Hopper) February 203 MLD7D

More information

60 farm jack. Distributed exclusively by Harbor Freight Tools Mission Oaks Blvd., Camarillo, CA 93011

60 farm jack. Distributed exclusively by Harbor Freight Tools Mission Oaks Blvd., Camarillo, CA 93011 60 farm jack 66183 Set up And Operating Instructions Distributed exclusively by Harbor Freight Tools. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read

More information

DISASSEMBLING & REASSEMBLING CARTRIDGE INSTALLING SEATPOST ON BIKE

DISASSEMBLING & REASSEMBLING CARTRIDGE INSTALLING SEATPOST ON BIKE INTRODUCTION BILL OF MATERIALS SPECIFICATIONS & TOOLS PROCEDURES DISASSEMBLING & REASSEMBLING CARTRIDGE INSTALLING SEATPOST ON BIKE OPERATION OF SEATPOST GIANT LIMITED WARRANTY 1 INTRODUCTION Congratulations

More information

OWNERS MANUAL. Model Shown with optional Primary Mooring Cleats. Portable Mooring System SAFETY OPERATION MAINTENANCE PARTS

OWNERS MANUAL. Model Shown with optional Primary Mooring Cleats. Portable Mooring System SAFETY OPERATION MAINTENANCE PARTS OWNERS MANUAL Model 2400 Shown with optional Primary Mooring Cleats. Portable Mooring System SAFETY OPERATION MAINTENANCE PARTS CAUTION: Before using your new Pier Tender, read rules for Safety, Operation,

More information

Congratulations on your purchase of a JC Series Performer trike! The Performer JC Series is designed for everything from touring to commuting and

Congratulations on your purchase of a JC Series Performer trike! The Performer JC Series is designed for everything from touring to commuting and Congratulations on your purchase of a JC Series Performer trike! The Performer JC Series is designed for everything from touring to commuting and shopping in the city. The JC Series frames are made of

More information

INTRODUCTION BILL OF MATERIALS SPECIFICATIONS & TOOLS PROCEDURES OPERATION OF SEATPOST GIANT LIMITED WARRANTY

INTRODUCTION BILL OF MATERIALS SPECIFICATIONS & TOOLS PROCEDURES OPERATION OF SEATPOST GIANT LIMITED WARRANTY INTRODUCTION BILL OF MATERIALS SPECIFICATIONS & TOOLS PROCEDURES OPERATION OF SEATPOST GIANT LIMITED WARRANTY 1 INTRODUCTION Congratulations on the purchase of your new GIANT CONTACT SWITCH seatpost. This

More information

COOPER POWER SERIES. D-73P3 bypass switches installation instructions. Switches MN008005EN. Effective April 2016 Supersedes S June 2013

COOPER POWER SERIES. D-73P3 bypass switches installation instructions. Switches MN008005EN. Effective April 2016 Supersedes S June 2013 Switches MN008005EN Effective April 2016 Supersedes S328-120-1 June 2013 D-73P3 bypass switches installation instructions COOPER POWER SERIES DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY The information,

More information

Traditional Basketball Set. Assembly & Installation Instructions

Traditional Basketball Set. Assembly & Installation Instructions Traditional & Pro Style Basketball Set Assembly & Installation Instructions Traditional Basketball Set Pro Style Basketball Set 3 0 5 0 S. A L V E R N O N W A Y T U C S O N, A Z 8 5 7 1 3 5 2 0. 7 9 0.

More information

INSTALLATION INSTRUCTIONS AT-SERIES ANCHOR ASSEMBLY PART NUMBER: F-04CAJP 450 LB. [204kg] MAXIMUM CAPACITY (PRO POOL LIFT)

INSTALLATION INSTRUCTIONS AT-SERIES ANCHOR ASSEMBLY PART NUMBER: F-04CAJP 450 LB. [204kg] MAXIMUM CAPACITY (PRO POOL LIFT) INSTALLATION INSTRUCTIONS AT-SERIES ANCHOR ASSEMBLY PART NUMBER: F-04CAJP 450 LB. [204kg] MAXIMUM CAPACITY (PRO POOL LIFT) - WARNING- IMPORTANT SAFETY INSTRUCTIONS 1. READ AND FOLLOW ALL INSTRUCTIONS.

More information

Revolution Gurney Attachment

Revolution Gurney Attachment Revolution Gurney Attachment PART NUMBER: F-30RSA-S2 (2nd SERIES) WEIGHT CAPACITY: 350 POUNDS - STANDARD REVOLUTION 300 POUNDS - DEEP DRAFT REVOLUTION MANDATORY LEAVE THIS MANUAL WITH LIFT OWNER Read &

More information

Sunset Swings By Health in Motion, LLC

Sunset Swings By Health in Motion, LLC Sunset Swings By Health in Motion, LLC Model 421 Lounge Swing Assembly and Operation Manual Record Serial Number Here www.sunsetswings.com by Health In Motion, LLC. 1/30/2013 Caution: READ! VERY IMPORTANT

More information

Cocoa Patio Pond with Lit Spillway

Cocoa Patio Pond with Lit Spillway Cocoa Patio Pond with Lit Spillway REMINDER CALL 1-888-755-5641 BEFORE RETURNING TO STORE. PACKAGE CONTENTS ITEM # GQSPPB/GQSPPW Questions, problems, missing parts? Before returning to your retailer, call

More information

SASK-A-POLE OWNERS AND USERS MANUAL

SASK-A-POLE OWNERS AND USERS MANUAL SASK-A-POLE OWNERS AND USERS MANUAL GENERAL INFORMATION The Saskatchewan Abilities Council s Sask-a-Pole accessibility and transfer aid is designed to help provide safe and easy access to chairs, beds,

More information

FLANGED TWO-PIECE BALL VALVES

FLANGED TWO-PIECE BALL VALVES INTRODUCTION This instruction manual includes installation, operation, and maintenance information for FNW flanged split-body ball valves. This manual addresses lever operated ball valves only. Please

More information

Personal Fall Arrest System. User s. Manual. Part Number January 2014 (Replaces July 2013)

Personal Fall Arrest System. User s. Manual. Part Number January 2014 (Replaces July 2013) Personal Fall Arrest System User s Manual Part Number 0182150 January 2014 (Replaces July 2013) Personal Fall Arrest Anchorage PFAS Personal Fall Restraint Anchorage Additional Information For additional

More information

ROPV R40 E Series User Manual

ROPV R40 E Series User Manual HARBIN ROPV INDUSTRY DEVELOPMENT CENTER ROPV R40 E Series User Manual For Use with the Following ROPV Pressure Vessel Models: R40 300E R40 450E Headquarters Tel:(+86)451-82267301 Fax:(+86)451-82267303

More information

InstallatIon and owner s InstrUCtIons

InstallatIon and owner s InstrUCtIons InstallatIon and owner s InstrUCtIons Wall Mount Series Adjustable and Fixed Height Goal Systems table of Contents Safety Instructions... 2 Goal Specifications... 3 Frame Attachment... 4 Frame Assembly

More information

TR5000 THE TOUGHEST TRAINING SYSTEM ON THE PLANET. MODEL NO. STRIKER TRAINER 2L Escalade Sports

TR5000 THE TOUGHEST TRAINING SYSTEM ON THE PLANET. MODEL NO. STRIKER TRAINER 2L Escalade Sports MODEL NO. TR5000 THE TOUGHEST TRAINING SYSTEM ON THE PLANET. STRIKER TRAINER TM 2L-7250-00 R Escalade Sport products may be manufactured and/or licensed under the following patents. 6419596, 6179733, 5919102,

More information

FLANGED TWO-PIECE BALL VALVES

FLANGED TWO-PIECE BALL VALVES INTRODUCTION This instruction manual includes installation, operation, and maintenance information for FNW flanged split-body ball valves. This manual addresses lever operated ball valves only. Please

More information

VOLLEYBALL SPIKE TRAINER. Assembly Instructions. Owner s Manual. Model # VST-400. Club Volleyball Gear

VOLLEYBALL SPIKE TRAINER. Assembly Instructions. Owner s Manual. Model # VST-400. Club Volleyball Gear VOLLEYBALL SPIKE TRAINER Model # VST-400 Wall-mount Volleyball Spike Trainer with 28 height adjustment range Assembly Instructions Owner s Manual Club Volleyball Gear 18434 Technology Drive, Morgan Hill,

More information

Model C Pipe Line Strainer 6, 8 & 10 Inch (DN150, DN200 & DN250) 250 psi (17,2) General Description. Technical Data. Page of 6 MAY, 2006 TFP1644

Model C Pipe Line Strainer 6, 8 & 10 Inch (DN150, DN200 & DN250) 250 psi (17,2) General Description. Technical Data. Page of 6 MAY, 2006 TFP1644 Technical Services: Tel: (00) 31-9312 / Fax: (00) 791-5500 Model C Pipe Line Strainer 6, & 10 Inch (150, & 250) 250 psi (17,2) General Description The welded steel body Model C Pipe Line Strainers (Ref.

More information

Cylinder Tilt Saddle Instruction Manual

Cylinder Tilt Saddle Instruction Manual Cylinder Tilt Saddle Instruction Manual MODELS: SDT05, SDT10, SDT15, SDT25 SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 Tel: 888-332-6419 - Fax: 816-448-2142 E-mail: sales@bvahydraulics.com

More information

2000 lb manual winch

2000 lb manual winch 2000 lb manual winch Model 41694 Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011

More information

TITAN FLOW CONTROL, INC.

TITAN FLOW CONTROL, INC. PREFACE: This manual contains information concerning the installation, operation, and maintenance of Titan Flow Control (Titan FCI) Simplex Basket Strainers. To ensure efficient and safe operation of Titan

More information

SERIES L4E & L6E LADDER EXTENSIONS

SERIES L4E & L6E LADDER EXTENSIONS SERIES L4E & L6E LADDER EXTENSIONS T AB L E O F C O N T E NT S V e n d o r D a t a Feature and Specification P a r t s L i s t Installation and Operation Instructions Limited Warranty 1 VENDOR DATA H ALLID

More information

ATD /8 x 50 Retractable Air Hose Reel Owner s Manual

ATD /8 x 50 Retractable Air Hose Reel Owner s Manual ATD-31166 3/8 x 50 Retractable Air Hose Reel Owner s Manual Features Heavy-gauge, all-steel reel assembly 8-position ratchet mechanism locks reel at desired hose length 5-position adjustable roller outlet

More information

Instruction Manual LIMITED 1 YEAR WARRANTY. Hydraulic Punch Driver Read this material before using this product.

Instruction Manual LIMITED 1 YEAR WARRANTY. Hydraulic Punch Driver Read this material before using this product. Instruction Manual Hydraulic Punch Driver 902-483 LIMITED 1 YEAR WARRANTY We make every effort to assure that its products meet high quality and durability standards, and warrant to the original purchaser

More information

3M Liqui-Cel EXF-14x28 and 14x40 Series Membrane Contactor

3M Liqui-Cel EXF-14x28 and 14x40 Series Membrane Contactor Membrane Contactors 3M Liqui-Cel EXF-14x28 and 14x40 Series Membrane Contactor Assembly and Disassembly Instructions 3M.com/Liqui-Cel TABLE OF CONTENTS I. Safety Information 3 II. Required Materials 4

More information

VOLLEYBALL SPIKE TRAINER. Assembly Instructions. Owner s Manual. Model # VST-100. Club Volleyball Gear WARNING

VOLLEYBALL SPIKE TRAINER. Assembly Instructions. Owner s Manual. Model # VST-100. Club Volleyball Gear WARNING VOLLEYBALL SPIKE TRAINER Model # VST-100 Assembly Instructions Owner s Manual WARNING To ensure safety, do not attempt to assemble this system without following all instructions carefully. Check entire

More information

RADROVER REAR RACK INSTALLATION MANUAL

RADROVER REAR RACK INSTALLATION MANUAL RADROVER REAR RACK INSTALLATION MANUAL WWW.RADPOWERBIKES.COM We are here to help! Please contact us at SUPPORT@RADPOWERBIKES.COM or 1-800-939-0310 if you have questions. REV022216 Welcome Thanks you for

More information

VL PONTOON/TRITOON DECK BRACKET 13 INSTRUCTIONS

VL PONTOON/TRITOON DECK BRACKET 13 INSTRUCTIONS VL PONTOON/TRITOON DECK BRACKET 13 INSTRUCTIONS REIMANN & GEORGER CORPORATION MARINE PRODUCTS BUFFALO, NY P/N 6112--- 01/08/14 TABLE OF CONTENTS CHAPTER TITLE PAGE 1 SAFETY... 1 1.1 Introduction... 1 1.2

More information

WATER HEATER THERMAL EXPANSION TANKS Owner s Manual. Safety Instructions Installation Maintenance Warranty. Models: 2-5 Gallon Capacity

WATER HEATER THERMAL EXPANSION TANKS Owner s Manual. Safety Instructions Installation Maintenance Warranty. Models: 2-5 Gallon Capacity WATER HEATER THERMAL EXPANSION TANKS Owner s Manual Safety Instructions Installation Maintenance Warranty Models: 2-5 Gallon Capacity Thank You for purchasing this Thermal Expansion Tank. Properly installed

More information

Yoke Block Instruction Manual

Yoke Block Instruction Manual Yoke Block Instruction Manual ! WARNING IMPORTANT: READ MANUAL COMPLETELY BEFORE OPERATING THIS DEVICE This manual contains instructions on periodically required checks to be performed by the user. These

More information

TL-12 FLUSH TANK. Manual Ref. # MN-??? Polyurethane Machinery Corp. REVISION 1.0

TL-12 FLUSH TANK. Manual Ref. # MN-??? Polyurethane Machinery Corp. REVISION 1.0 TL-12 FLUSH TANK Manual Ref. # MN-??? REVISION 1.0 Polyurethane Machinery Corp. Corporate: 1 Komo Dr, Lakewood, NJ 08701 Manufacturing: 2 Komo Dr, Lakewood, NJ 08701 Phone: 732-415-4400 Fax: 732-364-4025

More information

VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns , , , , , )

VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns , , , , , ) VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns 3714022, 3714028, 3714034, 3714040, 3714043, 3714046) REIMANN & GEORGER CORPORATION MARINE PRODUCTS BUFFALO, NY P/N 6112103 04/09/18 1 SAFETY 1.1 INTRODUCTION

More information

Pressure Relief Valve Instruction Manual

Pressure Relief Valve Instruction Manual CVR3-M0_062017 Pressure Relief Valve Instruction Manual MODEL: CVR3 SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 Tel: 888-332-6419 * Fax: 816-448-2142 E-mail: sales@bvahydraulics.com Website:

More information

Standard Collection Setup Manual

Standard Collection Setup Manual Standard Collection Setup Manual 727-391-9009 www.tourlinks.net Please register this product online at www.tourlinks.net WARNING! READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT. FAILURE TO

More information

/ FLT-M Quick Clean Rotary Airlock Valve Operators Manual. Kice Industries, Inc. RAV-M RAV-M

/ FLT-M Quick Clean Rotary Airlock Valve Operators Manual. Kice Industries, Inc. RAV-M RAV-M 1 Quick Clean Rotary Airlock Valve Operators Manual Kice Industries, Inc. RAV-M04-0000 RAV-M04-0000 2 INTRODUCTION When you purchased your new Kice equipment, you bought a dependable and quality-built

More information

COPY. **For U.S. and Canada Customers ONLY:** IF ASSISTANCE IS NEEDED,

COPY.  **For U.S. and Canada Customers ONLY:** IF ASSISTANCE IS NEEDED, MODEL #73729 WARNING Failure to comply with any of the warnings in these instructions may result in serious personal injuries such as cuts, broken bones, nerve damage, paralysis, brain injury, or death.

More information

INSTALLATION MANUAL Matheson Tri-Gas Cabinet Enclosures

INSTALLATION MANUAL Matheson Tri-Gas Cabinet Enclosures INSTALLATION MANUAL Matheson Tri-Gas Cabinet Enclosures MINT-0289-XX TABLE OF CONTENTS Limited Warranty... 3 User Responsibility... 3-4 General Service... 4 Safety Precautions.... 5 Physical Dimensions..

More information

600 / 600FC OWNER'S MANUAL

600 / 600FC OWNER'S MANUAL PROGRESSION 600 / 600FC OWNER'S MANUAL Issue 2 / Version E - Dec. 10, 1997 Copyright 1997 GAMMA Sports - All Rights Reserved PROGRESSION 600 / 600FC OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY

More information

Owner s. product. Failure injury

Owner s. product. Failure injury 100-Ft. Hose Reel Cart Owner s Manual WARNING: Read and understand all instructions, warnings, and cautions before using this product. Failure to follow the instructions, warnings, and cautions may result

More information

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS 18 GAUGE 1-1/4 INCH BRAD NAILER Model: 7611 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.

More information

VOLLEYBALL SPIKE TRAINER. Assembly Instructions. Owner s Manual. Model # VST-300. Club Volleyball Gear. For fixed-height Basketball Hoop Systems

VOLLEYBALL SPIKE TRAINER. Assembly Instructions. Owner s Manual. Model # VST-300. Club Volleyball Gear. For fixed-height Basketball Hoop Systems VOLLEYBALL SPIKE TRAINER Model # VST-300 For fixed-height Basketball Hoop Systems Assembly Instructions Basketball Hoop System Not Included Owner s Manual Club Volleyball Gear 18434 Technology Drive, Morgan

More information

Inflatable Stand Up Paddle Board Manual

Inflatable Stand Up Paddle Board Manual Inflatable Stand Up Paddle Board Manual V-Max AIR 12 6 Voyager AIR 11 6 Koa AIR 10 2 and 10 8 Heavy duty built in carrying handles Steel D Ring Built in Cargo Straps EVA Deck Pad High Pressure Air Valve

More information

Model B-1 Pipe Line Strainer 3, 4, 6 & 8 Inch (DN80, DN100, DN150 & DN200) 175 psi (12,1 bar) General Description. Technical Data

Model B-1 Pipe Line Strainer 3, 4, 6 & 8 Inch (DN80, DN100, DN150 & DN200) 175 psi (12,1 bar) General Description. Technical Data Technical Services: Tel: (800) 381-312 / Fax: (800) 71-5500 Customer Service/Sales: Tel: (215) 362-0700 / (800) 523-6512 Fax: (215) 362-5385 Model B-1 Pipe Line Strainer 3,, 6 & 8 Inch (DN80, DN100, DN150

More information

DT400/436 Tee Connector Installation Instructions

DT400/436 Tee Connector Installation Instructions Connectors Lorem ipsum and dolor Splices sit Amat Effective September 2014 Supersedes IS550-30-1 March 2011 MN650001EN DT400/436 Tee Connector Installation Instructions DISCLAIMER OF WARRANTIES AND LIMITATION

More information

V O L L E Y B A L L S E T

V O L L E Y B A L L S E T S E T Assembly & Installation Instructions 3 0 5 0 S. A L V E R N O N W A Y T U C S O N, A Z 8 5 7 1 3 5 2 0. 7 9 0. 7 0 4 0 8 0 0. 7 3 7. 5 3 8 6 F A X 5 2 0. 7 9 0. 7 1 2 7 i n t e r - f a b. c o m TABLE

More information

APCO ASU-SCAV & ASU-CAV SINGLE BODY COMBINATION AIR VALVES

APCO ASU-SCAV & ASU-CAV SINGLE BODY COMBINATION AIR VALVES APCO ASU-SCAV & ASU-CAV SINGLE BODY COMBINATION AIR VALVES Instruction D12039 December 2015 Instructions These instructions provide installation, operation and maintenance information for the. They are

More information

Instructions for Assembly and Operation

Instructions for Assembly and Operation Instructions for Assembly and Operation Congratulations on the purchase of your new bike! With proper assembly and maintenance it will offer you years of enjoyable riding! IMPORTANT: Carefully read and

More information

WEATHERIZING INSTRUCTIONS

WEATHERIZING INSTRUCTIONS FOR PNEUMATIC MASTS The Will-Burt Company 169 S. Main Street Orrville, OH 44667 www.willburt.com TP-4744301-C, 2017 The Will-Burt Company Pneumatic Mast Warranty Will-Burt warrants its pneumatic masts

More information

BS Series Basket Strainer

BS Series Basket Strainer BS Series Basket Strainer Operating, Installation, & Maintenance Manual Corrosion Resistant Fluid and Air Handling Systems. Dated 04-26-12 PRESSURE DROP SIMTECH strainers are engineered to offer the lowest

More information

GRAVITY BIKE RACK ASSEMBLY & OPERATING INSTRUCTIONS

GRAVITY BIKE RACK ASSEMBLY & OPERATING INSTRUCTIONS GRAVITY BIKE RACK 94479 ASSEMBLY & OPERATING INSTRUCTIONS Due to continuing improvement, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011

More information

SANTA CRUZ BICYCLES Cable Routing Procedure MY17

SANTA CRUZ BICYCLES Cable Routing Procedure MY17 SANTA CRUZ BICYCLES Cable Routing Procedure MY17 Copyright Santa Cruz Bicycles 2017 TABLE OF CONTENTS SAFETY INSTRUCTIONS... 3 CABLE ROUTING... 3 INTRODUCTION...3 TOOLS AND SUPPLIES...3 REAR DERAILLEUR

More information

4 and 8 Station PDS Control Installation & Operators Manual

4 and 8 Station PDS Control Installation & Operators Manual 4 and 8 Station PDS Control Installation & Operators Manual 1402-15 11/2000 June 2003 MW1402C Chore-Time Warranty 4 and 8 Station PDS Control Chore-Time Warranty Chore-Time Equipment ( Chore-Time ) warrants

More information

OPERATOR S MANUAL AND PARTS LISTING FOR THE. STM Mounted Harrow

OPERATOR S MANUAL AND PARTS LISTING FOR THE. STM Mounted Harrow MANUFACTURERS OF QUALITY AGRICULTURAL EQUIPMENT SINCE 1936 OPERATOR S MANUAL AND PARTS LISTING FOR THE STM Mounted Harrow With FH 5-Bar Section VERSION: 10-07AJF TO THE OWNER AND OPERATORS Before assembling

More information

Gym Dandy TEETER TOTTER TT-360. Model TT-360. Retain This Manual for Reference OWNER'S MANUAL

Gym Dandy TEETER TOTTER TT-360. Model TT-360. Retain This Manual for Reference OWNER'S MANUAL NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Gym Dandy TEETER TOTTER TT-360 Important Assembly Information Care and Maintenance Parts List Warranty

More information

Angled Sign Light with Shade

Angled Sign Light with Shade Angled Sign Light with Shade Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions

More information

VOLLEYBALL SPIKE TRAINER. Assembly Instructions. Owner s Manual. Model # VST-200. Club Volleyball Gear. For height-adjustable Basketball Hoop Systems

VOLLEYBALL SPIKE TRAINER. Assembly Instructions. Owner s Manual. Model # VST-200. Club Volleyball Gear. For height-adjustable Basketball Hoop Systems VOLLEYBALL SPIKE TRAINER Model # VST-200 Basketball Hoop System Not Included For height-adjustable Basketball Hoop Systems Assembly Instructions Owner s Manual Club Volleyball Gear 18434 Technology Drive,

More information

OPERATION AND INSTRUCTION MANUAL Flat Roof Anchor Model: FRA250L-10X-CTS

OPERATION AND INSTRUCTION MANUAL Flat Roof Anchor Model: FRA250L-10X-CTS OPERATION AND INSTRUCTION MANUAL Flat Roof Anchor Model: FRA250L-10X-CTS (Patent Pending) WARNING: ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT

More information

602 STRINGING MACHINE OWNER'S MANUAL

602 STRINGING MACHINE OWNER'S MANUAL PROGRESSION 602 STRINGING MACHINE OWNER'S MANUAL AL Issue 1- April 2000 Copyright 2000 GAMMA Sports - All Rights Reserved PROGRESSION 602 STRINGING MACHINE TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2...

More information

453 Series Steam Heated Vaporizing Regulator

453 Series Steam Heated Vaporizing Regulator ADI 0453A Certified ISO 9001:2000 453 Series Steam Heated Vaporizing Regulator INSTALLATION AND OPERATION INSTRUCTIONS Before Installing or Operating, Read and Comply with These Instructions Controls Corporation

More information

ALTERNATOR RACKS 135, 170 & 190 INSTRUCTIONS

ALTERNATOR RACKS 135, 170 & 190 INSTRUCTIONS Figure A Item # Description Quantity 1 Alternator Rack 1 1 3 4 11 5 10 8 2 Lower Mount Kit (see detail) 2 3 16mm M5 Swivel-Mount Bolt 2 4 M7 Washer 2 5 M6 Lock Nut 2 6 Lock Washer 2 7 Swivel Mount 2 8

More information

FOOSBALL ASSEMBLY, INSTRUCTIONS AND RULES PL

FOOSBALL ASSEMBLY, INSTRUCTIONS AND RULES PL FOOSBALL ASSEMBLY, INSTRUCTIONS AND RULES 56007 PL Waterloo Valley Road / Mt. Olive, NJ 07828 / www.sportcraft.com / (800) 526-0244 / Fax: (97) 47-54 MODEL # 56007 PL Congratulations on owning a new KT

More information

Hot Tapping Machine. OPERATIONS MANUAL and OPERATING INSTRUCTIONS

Hot Tapping Machine. OPERATIONS MANUAL and OPERATING INSTRUCTIONS 262-2040 Hot Tapping Machine For performing 1/4 6 Hot taps 285 psi or less. Municipal Water, Sewage, & Building Services Use OPERATIONS MANUAL and OPERATING INSTRUCTIONS WARNING: These instructions are

More information

12 Inch Barn Light. Owner s Manual

12 Inch Barn Light. Owner s Manual 12 Inch Barn Light Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions

More information

Compact Triple Cabinet Outlet Station Model B Installation and Operating Instructions

Compact Triple Cabinet Outlet Station Model B Installation and Operating Instructions PORTER Parker Hannifin Corporation Porter Instrument Division 245 Township Line Rd. P.O. Box 907 Hatfield, PA 19440-0907 USA (215) 723-4000 / fax (215) 723-5106 Compact Triple Cabinet Outlet Station Model

More information

SANTA CRUZ BICYCLES Geometry Adjust Flip Chip

SANTA CRUZ BICYCLES Geometry Adjust Flip Chip SANTA CRUZ BICYCLES Geometry Adjust Flip Chip Copyright Santa Cruz Bicycles 2017 TABLE OF CONTENTS SAFETY INSTRUCTIONS... 3 GEOMETRY ADJUST FLIP CHIP... 3 INTRODUCTION...3 TOOLS AND SUPPLIES...3 MY18 NOMAD

More information

Please Do Not Return This Product To The Store!

Please Do Not Return This Product To The Store! MODEL NUMBER: GM000W - GAMEMAKER TORCH O W N E R ' S M A N U A L PLEASE READ AND FOLLOW THIS MANUAL IN ITS ENTIRETY BEFORE USE. DOING SO WILL PROVIDE HELPFUL HINTS THAT WILL AID IN GETTING MAXIMUM USE

More information

Compact Triple Cabinet Outlet Station Model Installation and Operating Instructions

Compact Triple Cabinet Outlet Station Model Installation and Operating Instructions Compact Triple Cabinet Outlet Station Model 6258-1 Installation and Operating Instructions The Porter Compact Triple Outlet Station (6258-1) provides a quick, safe, and reliable method of connection to

More information

USER MANUAL. DM65 Manual Flush/Tilt Combo Mount

USER MANUAL. DM65 Manual Flush/Tilt Combo Mount USER MANUAL DM65 Manual Flush/Tilt Combo Mount 1 D1_1.11.11.indd 1 ! CAUTION When using this mounting system, basic precautions should be followed, including: Follow the entire installation/user s manual

More information

Page 1. Single Scull Car Rack Assembly and User s Manual " "

Page 1. Single Scull Car Rack Assembly and User s Manual  Page 1 Single Scull Car Rack Assembly and User s Manual Page 2 Items in the box: (2) V cradles (2) 4 rails (1) 1 3/4 X 18 rail coupler (4) 1/4-20 X 4 1/2 bolts (2) 1/4-20 X 2 1/2 bolts (12) 1/4 flat washers

More information

200 A, 15 and 25 kv class loadbreak bushing insert installation instructions

200 A, 15 and 25 kv class loadbreak bushing insert installation instructions Loadbreak Apparatus Connectors Effective October 2013 Supersedes March 2011 200 A, 15 and 25 kv class loadbreak bushing insert installation instructions S500-12-1 DISCLAIMER OF WARRANTIES AND LIMITATION

More information

STYRIGGER PRODUCT MANUAL

STYRIGGER PRODUCT MANUAL STYRIGGER PRODUCT MANUAL Thank you for choosing the Styrigger kayak and canoe stabilizer. A kayak or canoe equipped with a Styrigger (safety outrigger) is an excellent choice for a beginner or someone

More information

PCS 340 Core Saturator : 115 Volt : 230 Volt. Instruction Manual

PCS 340 Core Saturator : 115 Volt : 230 Volt. Instruction Manual PCS 340 Core Saturator 127-70: 115 Volt 127-70-1: 230 Volt Instruction Manual Updated 4/30/2015 Ver. 1.2 OFI Testing Equipment, Inc. 11302 Steeplecrest Dr. Houston, Texas 77065 U.S.A. Tele: 832.320.7300

More information

FLANGED MULTI-PORT BALL VALVES

FLANGED MULTI-PORT BALL VALVES INTRODUCTION This instruction manual includes installation, operation and maintenance information for flanged multi-port ball valves. This manual addresses lever operated ball valves only. Please refer

More information

35 TON HYDRAULIC PUNCH WARNING

35 TON HYDRAULIC PUNCH WARNING OPERATORS GUIDE REL-35T-PNC 35 TON HYDRAULIC PUNCH NOTICE Sizes, weights and tool specifications listed in this manual are subject to change without notice. Please consult factory for information and updates.

More information

Yoke Block Instruction Manual

Yoke Block Instruction Manual Yoke Block Instruction Manual ! WARNING IMPORTANT: READ MANUAL COMPLETELY BEFORE OPERATING THIS DEVICE This manual contains instructions on periodically required checks to be performed by the user. These

More information

Parts & Operators Manual

Parts & Operators Manual Parts & Operators Manual (888) 317-5878 www.talet.ca To The Owner General Comments Congratulations on the purchase of your new Talet Mat Grapple. Your unit was carefully designed and manufactured to give

More information

USER INSTRUCTION MANUAL CONCRETE BOLT ANCHORAGE CONNECTOR

USER INSTRUCTION MANUAL CONCRETE BOLT ANCHORAGE CONNECTOR Instructions for the following series products: Concrete Bolt Connector Models: 2100041, 2100066, 2104560, 2104561, 2104562 USER INSTRUCTION MANUAL CONCRETE BOLT ANCHORAGE CONNECTOR This manual is intended

More information

Triple Tine Mechanical Grapple

Triple Tine Mechanical Grapple Attachment Solutions Triple Tine Mechanical Grapple Operators Manual KENCO Mechanical Grapple Operation Manual 1 TABLE OF CONTENTS 170 State Route 271 Section I. General Information.... 3 Section II. Safety...

More information

PARK AVENUE 7' POOL TABLE WITH TABLE TENNIS & BENCHES ASSEMBLY INSTRUCTIONS

PARK AVENUE 7' POOL TABLE WITH TABLE TENNIS & BENCHES ASSEMBLY INSTRUCTIONS PARK AVENUE 7' POOL TABLE WITH TABLE TENNIS & BENCHES ASSEMBLY INSTRUCTIONS NG2530PR THANK YOU! Thank you for purchasing this product. We work around the clock and around the globe to ensure that our products

More information

STYLE 3414/3416 & 3421/3423 Apollo Monitor with Foldaway Legs OPERATING & MAINTENANCE INSTRUCTIONS

STYLE 3414/3416 & 3421/3423 Apollo Monitor with Foldaway Legs OPERATING & MAINTENANCE INSTRUCTIONS STYLE 3414/3416 & 3421/3423 Apollo Monitor with Foldaway Legs OPERATING & MAINTENANCE INSTRUCTIONS The Akron Style 3414/3416 & 3421/3423 Apollo Monitor is designed to provide efficient trouble-free operation

More information

Model ASSEMBLY and OPERATING INSTRUCTIONS

Model ASSEMBLY and OPERATING INSTRUCTIONS QUICK CHANGE AIR BRUSH KIT Model 93506 ASSEMBLY and OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd.,

More information

Index Table. Model 794. Installation, Operating and Maintenance Instructions

Index Table. Model 794. Installation, Operating and Maintenance Instructions CLOCKWISE MANUAL MAKING INTO CCW TABLE Index Table Model 794 Installation, Operating and Maintenance Instructions Black & Webster Products Division 545 Hupp Ave. P.O. Box 831, Jackson, Michigan 49204 2009

More information

isup MANUAL THANK YOU FOR PURCHASING A KAHUNA isup, WE HOPE YOU HAVE MANY YEARS OF PADDLING ENJOYMENT.

isup MANUAL THANK YOU FOR PURCHASING A KAHUNA isup, WE HOPE YOU HAVE MANY YEARS OF PADDLING ENJOYMENT. i isup MANUAL THANK YOU FOR PURCHASING A KAHUNA isup, WE HOPE YOU HAVE MANY YEARS OF PADDLING ENJOYMENT. THIS MANUAL IS A GENERAL GUIDELINE FOR SET-UP, CARE AND PROPER USE. PLEASE REFER TO OUR WEBSITE

More information

SSS SWEEPERS MODELS MS-31 & MS-39

SSS SWEEPERS MODELS MS-31 & MS-39 SSS SWEEPERS MODELS MS-31 & MS-39 INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS READ THIS BOOK This operator s book has important information for the use and safe operation of this machine. Read this

More information

4-in-1 Professional Inflator Kit

4-in-1 Professional Inflator Kit 4-in-1 Professional Inflator Kit Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety

More information

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS 18 GAUGE 2 INCH BRAD NAILER Model: 7555 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.

More information

Owner s Manual & Safety Instructions

Owner s Manual & Safety Instructions Owner s Manual & Safety Instructions Save Save This This Manual Manual Keep manual for the safety warnings and precautions, assembly, Keep manual for the safety warnings and precautions, assembly, operating,

More information

1000-Lb. Rapid Lift Hydraulic Table

1000-Lb. Rapid Lift Hydraulic Table 1000-Lb. Rapid Lift Hydraulic Table Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety

More information

DAKOTA 2006 DUMP BOX ILLUSTRATED PARTS MANUAL

DAKOTA 2006 DUMP BOX ILLUSTRATED PARTS MANUAL DAKOTA 00 DUMP BOX ILLUSTRATED PARTS MANUAL Copyright 00 Dakota Peat and Equipment, Inc. p/n 0 INTRODUCTION To ensure optimum performance and safety, always purchase genuine DAKOTA replacement parts and

More information

TOP VALVE. Pat. #5,857,486 & 5,944,050. Mid-Range Pressure PSIG Back Pressure and Pressure Relief Valves. Instruction Manual

TOP VALVE. Pat. #5,857,486 & 5,944,050. Mid-Range Pressure PSIG Back Pressure and Pressure Relief Valves. Instruction Manual TOP VALVE Pat. #5,857,486 & 5,944,050 Mid-Range Pressure 50 232 PSIG Back Pressure and Pressure Relief Valves Instruction Manual Please Note: This instruction manual provides detailed information and instructions

More information

OPERATOR S MANUAL. Fabric Grass Catcher PART NO PRINTED 1/2011 PRINTED IN USA

OPERATOR S MANUAL. Fabric Grass Catcher PART NO PRINTED 1/2011 PRINTED IN USA OPERATOR S MANUAL Fabric Grass Catcher Models: GC-F4 Congratulations on owning a Scag mower! This manual contains the operating instructions and safety information for your Scag mower accessory. Reading

More information

OWNER'S MANUAL. Copyright 1999 ATS - All Rights Reserved

OWNER'S MANUAL. Copyright 1999 ATS - All Rights Reserved OWNER'S MANUAL AL Issue 2 - August 19, 1999 Copyright 1999 ATS - All Rights Reserved OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... ASSEMBLY INSTRUCTIONS PAGE 4... MOUNTING THE RACQUET PAGE

More information

IMPORTANT: RECEIVING INSTRUCTIONS:

IMPORTANT: RECEIVING INSTRUCTIONS: Instruction Sheet Sidewinder Mechanical Bender IMPORTANT: RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any shipping damage is found, notify carrier at once.shipping damage

More information