1 Owner s Manual PAP M85 NP SEMI-AUTO PISTOL Cal. 5.56X45MM (.223) Congratulations on your purchase of the PAP M85 NP Semi-Auto Pistol. With proper care and handling, it will give you long, reliable service. The PAP M85 NP is chambered for the 5.56x45mm (.223) cartridge and uses a standard M16 magazine. Please note this pistol was designed for use with Standard USGI aluminum magazines. If you use composite magazines they may not drop free. We specifically disclaim any responsibility for damage or injury whatsoever, occurring as a result of the use of faulty, non-standard or remanufactured ammunition, any modifications or changes made to the firearm; improper use or unsafe handling of the firearm. Always keep this manual with your firearm. Make sure you understand all the warnings, operation instructions and safety procedures. When you lend, give or sell the firearm, be sure this manual goes with it. You can get a copy of this manual from Century Arms, Inc. on request. FIREARMS SAFETY IS THE SOLE RESPONSIBILITY OF THE SHOOTER. ALWAYS TREAT ALL FIREARMS AS IF THEY WERE LOADED AT ALL TIMES! IMPORTANT! READ ALL INSTRUCTIONS AND WARNINGS IN THIS BOOKLET BEFORE USING THIS FIREARM Century International Arms, Inc. All rights reserved.
2 IMPORTANT SAFETY MESSAGE Children are attracted to and can operate firearms which can cause severe injuries or death. Prevent child access by always keeping guns locked away and unloaded when not in use. If you keep a loaded firearm where a child obtains and improperly uses it, you may be fined or sent to prison. Firearm Safety Depends on You A gun is only as safe as the person operating it. You can never be overly careful when handling a firearm. Carelessness is often the cause of shooting accidents, such as failing to keep the muzzle pointed in a safe direction, not being sure of your target and what is behind it, failing to properly engage the safety, leaving ammunition in the chamber or using improper loads. Since a bullet can never be called back once fired, such errors in gun handling can result in the loss of life, severe injury or property damage thus, it is crucial for your safety and the safety of those around you that you learn the principles of safe gun handling and storage before you begin to use your new firearm. Be a safe shooter - please read this instruction book thoroughly even if this is not your first firearm purchase as not all firearms are the same. The first step in being a safe shooter is to learn the rules for the safe operation and handling of firearms. There is nothing more important in gun handling than safety. THE TEN COMMANDMENTS OF FIREARM SAFETY The Ten Commandments of Firearm Safety must be etched into your memory before you begin to handle firearms. These rules are intended to be followed by all persons handling firearms in the field, on the range or at home. Please read, review and understand these rules before you begin to use or even take your new firearm out of its box. Remember, firearms safety depends on you! Memorizing these safety rules will help prevent gun accidents. Please study these safety rules before handling your firearm. Commandment #1 Always Keep the Muzzle Pointed in a Safe Direction This is the most basic and most important safety rule. A safe direction is one in which an accidental discharge will not cause injury to yourself, to others or property damage. This is particularly important when loading or unloading your firearm. Never point your gun at anything you do not intend to shoot. Treat every gun as if it were loaded at all times. Commandment #2 Firearms Should Be Unloaded When Not Actually in Use Firearms should only be loaded when you are in the field or on the target range or shooting area, ready to shoot. When not in use, firearms and ammunition should be secured in a safe place, separate from each other. Remember to unload your firearm completely so that there is no ammunition in the chamber or magazine. Before handling this or any firearm, or handing it to someone else, visually check the chamber and magazine to ensure they do not contain ammunition. Always keep the gun s action open when not in use. Never assume a gun is unloaded - even if you were the last person to use it. Never cross a fence, climb a tree, wade through a stream or perform any awkward movement with a loaded gun. When in doubt, unload your gun! Never pull or push a loaded firearm Page Century International Arms, Inc. PAP M85 NP Pistol Manual
3 toward yourself or another person. Never carry a loaded gun in a scabbard, a holster not being worn or a gun case - common sense prevails in gun safety! Commandment #3 Don t Completely Rely on Your Gun s Safety Treat every gun as though it could fire at any time, even if you are not applying pressure to the trigger. The safety on a firearm is a mechanical device which, like any such device, can become inoperable at the worst possible time and fail to function. By mistake, you may think the safety is ON when it actually is not. Or you may think your gun is unloaded when there is actually a round of ammunition in it. The safety serves as a supplement to proper gun handling but cannot serve as a substitute for common sense. Never handle a gun carelessly and assume that the gun won t fire just because the safety is on. Never touch the firearm s trigger until you are ready to shoot. Keep your fingers away from the trigger when loading or unloading. Never pull the trigger when the safety is engaged or when the safety is positioned between the SAFE and FIRE positions. Never place your finger on the trigger unless you intend to fire. Alcohol, Drugs and Guns Don t Mix. Make No Mistake About It! Never handle firearms after consuming alcohol or taking drugs that can affect your judgment. Shoot sober! Alcohol, certain kinds of drugs and firearms don t mix. Safe firearms handling requires alertness and concentration on one s actions. You cannot handle a firearm safely after consuming alcohol. Never consume anything that can impair your judgment or physical coordination when handling a firearm. Commandment #4 Be Sure of Your Target And What Is Beyond It! Once fired, a bullet (or shot charge) can never be called back; so before you shoot, know where the bullet is going and what it will strike. Be certain your shot will not injure someone or strike something beyond the target. Never fire in the direction of noise, a movement or at any object you cannot positively identify. Be aware that a.22 Short bullet can travel over 1 ¼ miles. A centerfire cartridge, such as the.30-06, can send its bullet over 3 miles. Shotgun pellets can travel 500 yards and a shotgun slug has a range of over a half mile. Make sure your shot has a safe backstop such as a hillside. Keep in mind how far the bullet will travel if it misses your intended target. Once fired, a bullet can never be called back. You are responsible for your actions and judgment. PAP M85 NP Pistol Manual Commandment #5 Use the Correct Ammunition Every firearm is designed to use a certain caliber or gauge of ammunition. It is important that you use the correct ammunition for your firearm. Information on the correct ammunition to use with your firearm appears in the firearm s instruction manual and the manufacturer s markings on the firearm itself. Use of the wrong ammunition, improperly reloaded ammunition or corroded ammunition can result in the destruction of the firearm, serious personal injury and/or death. Form the habit of examining every round of ammunition before you put it into your gun to ensure it is of the proper gauge or caliber and that it is in good condition Century International Arms, Inc. Page 3
4 Commandment #6 If Your Gun Fails to Fire When the Trigger Is Pulled, Handle With Care If a cartridge or shell does not fire when the trigger is pulled, follow Commandment #1 and keep the firearm s muzzle pointed in a safe direction. Keep the muzzle down range with the action closed and wait at least 30 seconds (to ensure that the ammunition is not delayed in firing) before carefully opening the action, unloading the firearm and safely disposing of the ammunition. Commandment #7 Always Wear Eye and Ear Protection When Shooting Exposure to shooting noise can permanently damage hearing. Flying debris, such as powder residue and ejected cartridge cases, can injure your eyes. Thus, it is only common sense to wear both eye protection (such as shooting glasses) and ear protection (such as a sound-muffling headset) whenever shooting. Also, wear eye protection when cleaning or disassembling your gun to ensure that cleaning solvent and tensioned parts (such as springs) do not come into contact with your eyes. Commandment #8 Be Sure the Barrel Is Clear of Obstructions Before Shooting Discharging a firearm with an obstruction in the barrel can result in personal injury, property damage and/or death. Before you load your firearm, check the chamber and magazine to ascertain that no ammunition is inside. Also, check the inside of the barrel (called the bore ) to ensure it is free of obstructions. Even a small amount of mud, snow or excess lubricating oil or grease in the bore can cause excessive pressures resulting in a bulged or burst barrel which can injure or kill the shooter and bystanders. It is a good idea to make a habit of cleaning the bore and checking for obstructions with a cleaning rod just before each shooting session. If the noise or recoil experienced upon firing seems low or weak, or something doesn t feel right, cease firing immediately and check to make sure that there is no obstruction in the barrel. Placing an undersized shell or cartridge into a gun (such as a 20 gauge shell in a shotgun chambered for 12 gauge ammunition) can result in the smaller round of ammunition falling into the barrel and acting as an obstruction. When a round is subsequently fired, the barrel may burst, causing injury to the shooter and bystanders. For reference, re-read Commandment #5. Commandment #9 Do Not Alter or Modify Your Gun and Have It Serviced Regularly Firearms are complex mechanisms that are designed to function properly in their original condition. Any alterations or changes made to a firearm after its manufacture can make the gun unsafe and will void its warranty. Do not jeopardize your safety or the safety of others by altering the trigger, mechanical safety or other mechanisms of your firearm. You should have your firearm periodically checked for proper functioning and serviced by a qualified gunsmith. Commandment #10 Learn the Mechanical and Handling Characteristics of Your Firearm Not all firearms operate the same way. The method of carrying, handling and operating firearms varies with the mechanical characteristics of each gun. Thus, you Page Century International Arms, Inc. PAP M85 NP Pistol Manual
5 should never handle any firearm until you become familiar with the safe handling, loading, unloading and carrying procedures for that particular firearm, as well as the rules for safe gun handling in general. LEAD WARNING! Discharging firearms in poorly ventilated areas, cleaning firearms or handling ammunition may result in exposure to lead and other substances known to cause birth defects, reproductive harm and other serious injuries. Have adequate ventilation at all times when shooting. Wash hands thoroughly after exposure. Basics of Safe Gun Handling 1. Always keep the muzzle pointed in a safe direction. 2. Firearms should be unloaded when not actually in use. 3. Don t totally rely on your gun s safety. 4. Be sure of your target and what is beyond it. 5. Use the correct ammunition for your firearm. 6. If your gun fails to fire when the trigger is pulled, handle with care. 7. Always wear eye and ear protection when shooting and cleaning. 8. Be sure the barrel is clear of obstructions before shooting. 9. Don t alter or modify your firearm and have your firearm(s) serviced regularly. 10. Learn the mechanics and handling characteristics of the firearm you are using. Safe gun handling depends on you! A safe shooter is a knowledgeable shooter. WARNING! STOP SHOOTING IMMEDIATELY AND UNLOAD YOUR FIREARM if your firearm develops a mechanical malfunction; binding or stoppage, spitting powder/gas, a cartridge primer is punctured, a cartridge case is bulged or ruptured, or the sound on firing does not sound quite right. Do NOT try one more shot, but unload your firearm and take it and the ammunition to a qualified gunsmith or send it back to Century Arms for examination. Do not assume that the firearm is empty merely because you checked the chamber. You must also check the bore for any obstruction. WARNING! Always ensure that the ammunition you are using is clean, undamaged and of the proper caliber before loading your pistol. The manufacturer and distributor of this pistol disclaim any liability for the use of remanufactured, reloaded or hand-loaded ammunition. Protect your investment in this fine firearm by using only factory fresh, quality ammunition. The use of improper caliber or low quality ammunition could result in injury, death and/or property damage upon firing. Remember, firearms safety depends on you! Specifications: PAP M85 NP Caliber: 5.56x45mm (.223). Type of Firearm: semi-automatic pistol. Magazine Capacity: 30 rds. Overall Length: Barrel Length: Weight: 6.55 lbs. PAP M85 NP Pistol Manual 2013 Century International Arms, Inc. Page 5
6 Illustration #1 Diagram showing major operational parts of the PAP M85 NP Semi Auto Pistol Study of this picture will aid you in understanding the instructions in this booklet Recoil spring cam 2. Safety lever 3. Receiver 4. Rear sight 5. Bolt cocking handle 6. Gas tube securing pin 7. Upper handguard 8. Gas tube 9. Front sight 10. Flash hider 11. Barrel 12. Lower handguard 13. Magazine 14. Magazine release button 15. Trigger 16. Pistol Grip Safety: The safety lever is in the SAFE position when it is moved to its uppermost (top) on the receiver. You should hear an audible click when it is correctly in place. (See Illustration #2.) NOTE: When the safety lever is in its lower position on the receiver, the safety lever is in the FIRE position. (See Illustration #3.) Illustration #2 Illustration #3 Safety lever in upper SAFE position. Safety lever in lower or FIRE position. Pulling the trigger when the safety lever is in the lower position will result in the pistol firing if there is a round in the chamber! Exercise extreme caution when handling pistol in this condition. Bolt Cocking Handle: Located on right hand side of the firearm protrudes from bolt used for pulling bolt rearward. (See Illustration #4.) Page Century International Arms, Inc. PAP M85 NP Pistol Manual
7 Bolt Catch: To use the bolt catch, move the safety lever to the FIRE position and pull the bolt to the rear and then push the safety lever up to the "SAFE" position so that it engages the bolt cocking handle which will lock the bolt to the rear, when you release the bolt cocking handle, the bolt will remain locked to the rear. (See Illustration #5.) To release the bolt and allow it to move forward, press the safety lever down to the FIRE position. (See Illustration #3.) Illustration #4 Illustration #5 Bolt cocking handle. SAFE position with the bolt locked to the rear. To Load the Pistol WARNING! Before loading, make sure the inside of the barrel is free of dirt or other obstructions. WARNING! Always check each cartridge to ensure it is of the correct caliber before loading the firearm. WARNING! Never load a firearm indoors. An accidental discharge will cause property damage, serious injury and/or death! Never use live ammunition to function test your pistol indoors. WARNING! Keep fingers away from the trigger while loading. WARNING! Keep muzzle pointed in a safe direction. WARNING! The safety lever should not extend below the safety lever stop on the bottom of the receiver or rise past the receiver cover. If it does, put the lever in the safe position by rotating it either up or down into the safe position. If this occurs, have the pistol inspected by a competent gunsmith before further use. 1. Place the safety lever in the SAFE position. (See Illustration #2.) 2. Load the magazine with the correct ammunition by pressing the cartridges one at a time into the magazine s feed lips. When loading the rounds into the magazines ensure the base of the cartridge is in contact with the back of the magazine. (See Illustration #6.) 3. Install the loaded magazine by placing it into the magazine box and sliding it up until it locks into place. Pull down on the magazine to insure it has properly locked into place (See Illustration #7.) 4. Keeping the muzzle pointed in a safe direction, move the safety lever downward to the FIRE position. WARNING! Pulling the trigger when the safety lever is in this lower position will result in the pistol firing a round. To avoid serious injury, death or causing property damage, make sure you know the SAFE and FIRE positions of the safety lever before attempting to load your pistol! PAP M85 NP Pistol Manual 2013 Century International Arms, Inc. Page 7
8 Illustration #6 Illustration #7 5. Pull back the bolt cocking handle to its fully-rearward position and release. As it moves rapidly forward under spring pressure, the bolt will strip a round from the magazine and insert it into the chamber. The pistol is now loaded and ready to fire. (See Illustration #8.) 6. Place the pistol back on SAFE. (See Illustration #2.) Illustration #8 Round being stripped from magazine. WARNING! The pistol is now loaded and will fire if the safety lever is moved downward to the FIRE position and the trigger is pulled! Handle with extreme caution and keep the muzzle (the end of the barrel) pointed in a safe direction! To Fire the Pistol 1. Keeping the 10 Commandments of Shooting Safety in mind, aim the pistol downrange at the target. When firing this pistol you may need to experiment with different shooting styles until you find the method which best suits your sporting activity. Remember to always fire the pistol in such a manner that you can maintain a safe muzzle direction at all times. 2. Disengage the safety lever by moving it to the "FIRE" position. (See Illustration #3.) 3. After aligning the sights on your target. Place your finger inside the triggerguard and on the trigger. 4. Keeping your sights aligned on the target. Slowly pull the trigger to fire the first round. 5. Being a semi-automatic pistol, the pistols action (its moving parts) will cycle after the first round is fired. As the bolt moves rearward, the extractor will pull the empty cartridge case from the chamber and eject it from the pistol. (Make sure there are no bystanders in close proximity on either side of the pistol who could be injured by the ejected cartridge case or gasses expelled from the pistol.) NOTE: If the trigger is pressed again, the pistol will fire! Keep the pistol pointed in a safe direction. 6. Firing may be continued in this manner until the magazine is empty. 7. When firing is finished, place the safety lever in the SAFE position. (See Illustration #2.) Page Century International Arms, Inc. PAP M85 NP Pistol Manual
9 WARNING! Always unload your pistol immediately after use and prior to cleaning and storage to minimize the risk of an accidental discharge. If your pistol ever fails to fire keep it pointed at the target for at least 30 seconds in the event of a hangfire (slow ignition). If the round still does not fire, remove the magazine, eject and discard the bad round. Reload the pistol to resume firing. Unloading the Pistol WARNING! Keep muzzle pointed in a safe direction. 1. Move the safety lever to the "SAFE" position. (See Illustration #2.) 2. Remove the magazine from the pistol. With your left hand holding the forearm, remove your right hand from the pistol grip and grasp the magazine, using your thumb depress the magazine release button. (See Illustration #9.) While at the same time pulling down on the magazine until it is clear of the magazine well. (See Illustration #10.) Illustration #9 Illustration #10 Magazine release button Press in on the magazine release button to remove the magazine from the pistol. 3. Move the safety lever to the FIRE position. (See Illustration #3.) Check the pistol's chamber to ensure it does not contain a round by pulling back on the bolt cocking handle (See Illustration #8) and locking it in place with the bolt catch on the safety lever. (See Illustration #5). Inspect the chamber to ensure it is empty. Once you determine the chamber is empty and no magazine is in the pistol, push down on the safety lever and let the bolt go forward. 4. In the event that a cartridge remains in the chamber after pulling the trigger and the extractor fails to remove it (whether or not it has fired), you should remove the magazine, then work the bolt cocking handle several times to try to eject the cartridge. If this does not eject the cartridge, ride the bolt cocking handle home (slowly allow it to return to its forward position without allowing it to impact the back of the cartridge casing). Follow the instructions found on this page to field strip your pistol before attempting to remove the cartridge. If after field stripping your pistol you are still unable to remove the cartridge casing, do not reassemble the pistol. Take the pistol to a competent gunsmith to remove the round and ensure proper functioning. WARNING! The pistol will fire if the magazine is removed and if the trigger is pulled when a cartridge is in the chamber. WARNING! If dropped, any firearm could fire when there is a cartridge in the chamber and the safety lever is in the "FIRE" position. PAP M85 NP Pistol Manual 2013 Century International Arms, Inc. Page 9
10 Field Stripping WARNING! Before beginning the disassembly process, check to ensure the pistol is not loaded. To do so, follow the procedures detailed in the Unloading the Pistol section on page 9. WARNING! Wear eye protection, such as shooting glasses or goggles, when disassembling your firearm to protect your eyes from tensioned parts, such as springs that could be dislodged during disassembly. 1. Remove the magazine from the pistol. To do so, follow the procedures detailed in the Unloading the Pistol section on page Move the safety lever to the "FIRE" position by rotating the safety lever downward. (See Illustration #3.) 3. Check the pistol's chamber to ensure it does not contain a round by pulling back on the bolt cocking handle (See Illustration #8) and locking it in place with the bolt catch on the safety lever. Inspect the chamber to ensure it is empty. Once you determine the chamber is empty and no magazine is in the pistol, push down on the safety lever and let the bolt go forward. 4. While maintaining a safe muzzle direction, raise the receiver cover by holding the pistol in a secure position (across your lap, resting on a table, etc.) and grasping the rear part of the receiver with your right hand, depress the spring loaded release button on the rear of the receiver. Press the recoil spring cam forward. Then raise the receiver cover from the back end first with your left hand. (See Illustration #11.) 5. Remove the recoil spring assembly from the pistol by holding the forward portion of the receiver with your left hand and pressing on the back of the recoil spring cam with your right hand until its rear face leaves the groove in the rear of the receiver. Lift the recoil spring cam and remove the recoil spring assembly from the bolt carrier channel. (See Illustration #12.) NOTE: The recoil spring assembly is under spring pressure. Hold on to the assembly when removing it or injury could result. Illustration #11 Illustration #12 6. Remove the bolt carrier and bolt from the pistol by holding the receiver with your left hand and the cocking handle with your right hand. Pull the bolt carrier and bolt to the rear as far as possible. Once the back of the bolt carrier contacts the backplate of the receiver. Lift the rear portion of the bolt carrier and remove it and the bolt from the receiver. (See Illustration #13.) 7. Remove the bolt from the bolt carrier by turning the bolt carrier over and holding it in your left hand. (See Illustration #14.) Rotate what is now the top of the bolt to the right and move it rearward with your right hand so that the guide lug on the bolt leaves the channel in the bolt carrier. You can now remove the bolt from the bolt carrier by moving it forward and out of its guide hole. Page Century International Arms, Inc. PAP M85 NP Pistol Manual
11 Illustration #13 Illustration #14 8. Remove the gas tube assembly and upper handguard from the pistol by holding the forward portion of the receiver with your left hand and pressing in the gas tube securing pin. (See Illustration #15.) Then, lift the rear of the gas tube vertically out of its groove in the rear of the rear sight base and remove the front end of the gas tube from the gas block. Illustration #15 Reassembly 1. Attach the gas tube assembly and upper handguard by holding the pistol by the forward portion of the receiver with your left hand, and with your right hand install the front end of the gas tube on the gas block. Align the gas tube end with the groove in the rear sight base and rotate it downward until it is fully seated in the rear sight base. When the gas tube assembly is fully seated in the rear sight base, the gas tube securing pin will move out and over the gas tube to lock it in place. 2. Install the bolt back in the bolt carrier by first holding the bolt carrier upside down in your left hand with the Illustration #16 gas piston facing away from you. Then take the bolt in your right hand with the bolt face facing away from you and the guide lug facing upward. Insert the bolt shaft into the guide hole on the bolt carrier and bring the bolt fully rearward. Align the bolt guide lug with the channel in the bolt carrier and rotate the bolt to the left. Once the guide lug has entered the channel in the bolt carrier continue to rotate until the bolt has moved forward as far as possible. (See Illustration #16.) PAP M85 NP Pistol Manual 2013 Century International Arms, Inc. Page 11
12 3. Make sure that the hammer is cocked (locked underneath the sear) before attempting to install the bolt carrier. 4. Install the bolt carrier and bolt back onto the receiver by holding the forward portion of the receiver with your left hand and with your right hand take the bolt and bolt carrier as shown in Illustration #19 ensuring that your thumb is placed on the back of the bolt to hold it fully forward. Insert the gas piston into the gas tube end and align the back face of the bolt carrier with the inside face of the back plate of the receiver. Using the heel of your right hand, depress the bolt carrier against the pressure from the hammer spring so that the guide grooves on the sides of the bolt carrier are aligned with the rails on the receiver and move the bolt carrier to its fully forward position. (See Illustrations #17 - #19.) Illustration #17 Illustration #18 Illustration #19 5. Install the recoil spring assembly on the pistol by holding the forward portion of the receiver with your left hand, and with your right hand, insert the recoil spring retainer into the bolt carrier channel. Move the recoil spring cam forward, placing its guide lugs in front of the grooves in the receiver rear plate. Depress the recoil spring cam until its guide lugs are aligned with the channel on the top of the receiver rear plate. Release pressure on the recoil spring cam which will allow it to move rearward and lock into the receiver. 6. To install the receiver cover on the pistol, begin by rotating the rear sight upward so that it is out of the way. Rotate the receiver cover down until it locks into position 7. Move the safety lever to the "SAFE" position. (See Illustration #2.) Cleaning the Pistol WARNING! Before beginning the cleaning process, check to ensure the pistol is unloaded. (See the Unloading the Pistol section on page 9.) WARNING! You should wear eye protection, such as shooting glasses or goggles, when cleaning your firearm to protect your eyes from tensioned parts, such as springs, that may become dislodged during disassembly. 1. Obtain a quality cleaning kit and thoroughly review the manufacturer's instructions. 2. Follow the pistol disassembly procedures. (See page 10.) 3. To clean the barrel, select the correct caliber cleaning brush and attach it to a cleaning rod. 4. Dampen the brush with gun cleaning solvent and then push the brush through the barrel several times. Page Century International Arms, Inc. PAP M85 NP Pistol Manual
13 5. Remove the brush and attach a correctly sized cloth cleaning patch to the cleaning rod and push it through the barrel several times to remove loosened fouling. 6. Repeat this process with the brush and cleaning patches until a final patch comes out clean after swabbing the bore. Lightly oil the bore. 7. Remove shooting residue from the pistol's action parts and outer surfaces by wiping them with a soft cloth dabbed in gun cleaning solvent. Then be sure to remove all excess solvent and dry them. 8. Finally, wipe down all outer surfaces with a soft cloth dipped in a good quality gun oil. WARNING! There may be sharp edges on parts of the firearm. Keep your fingers protected by wearing a pair of protective gloves when cleaning. WARNING! You should wear eye protection, such as shooting glasses or goggles, when cleaning this pistol to protect your eyes from tensioned parts, such as springs, that could become dislodged during the cleaning procedures. WARNING! Excessive use of cleaning solvents or lubricants can adversely affect your pistol's functioning. Wipe the inside of the barrel dry before firing and ensure that it is free of obstructions. WARNING! Some cleaning solvents produce hazardous vapors. Read and follow the solvent manufacturer s cautions found on the product s package. WARNING! Handling ammunition and cleaning firearms results in exposure to lead and other substances that can pose health risks. Wash your hands and face after firing your pistol or after cleaning it. WARNING! This firearm should be checked periodically for worn or damaged parts by a competent gunsmith. This will help ensure its safe functioning and a long service life. Cleaning Intervals Always clean your pistol as soon as possible after firing to prevent buildup of shooting residue and to prevent corrosion from starting. To maintain your pistol in good working order, it should be cleaned regularly even if it has not been fired. If you live in a low-humidity area, this may mean doing a full clean once or twice a year; but if you live in a high-humidity area, it may be necessary to clean your pistol as often as once a week. NOTE: In freezing weather (below 32 F. or 0 C.), the use of a dry lubricant (instead of oil) for lubrication may work better. PAP M85 NP Pistol Manual 2013 Century International Arms, Inc. Page 13
14 Storage Your pistol should be thoroughly cleaned and lightly lubricated before being put away for storage. A light coating of good quality gun oil should be applied to all exposed surfaces. Remove all excess lubrication and use a cleaning rod and cleaning patch to make sure that the bore (the inside of the barrel) is dry and free of obstructions when you remove your pistol from storage and before firing it. CHECK TO ENSURE THAT YOUR PISTOL IS NOT LOADED BEFORE STORING IT. ALWAYS STORE FIREARMS AND AMMUNITION SEPARATE FROM EACH OTHER AND OUT OF REACH OF CHILDREN. REFERENCE YOUR HOME STATE'S FIREARMS REGULATIONS FOR SAFE STORAGE OF FIREARMS AND AMMUNITION. NOTE: The use of reloaded, remanufactured, hand-loaded or other non-standard ammunition may result in damage to the pistol and injury or death to the shooter and/or bystanders. The manufacturer does not accept responsibility for malfunctions resulting from the such use. Illustration #23 Illustrated Parts Breakdown Page Century International Arms, Inc. PAP M85 NP Pistol Manual
15 # Part name 1. Receiver 2. Barrel 3. Front guard retain 4. Gas tube securing block 5. Gas block/front sight base 6. Flash hider 7. Flash hider detent pin 8. Flash hider detent spring 9. Flash hider detent pin retaining pin 10. Front sight 11. Flip up front sight 12. Flip up front sight spring 13. Flip up front sight detent 14. Front trunnion (not available) 15. Rear trunnion (not available) 16. Hammer and trigger pin 17. Hammer 18. Trigger 19. Disconnector 20. Disconnector spring 21. Hammer spring 22. Hammer/trigger pin retaining spring 23. Cover pin 24. Washer 25. Gas tube catch pin 26. Safety lever 27. Pistol grip screw # Part name 28. Pistol grip 29. Pistol grip washer 30. Magazine adaptor 31. Magazine release button 32. Magazine release spring 33. Magazine catch 34. Magazine adaptor pin 35. Firing pin 36. Extractor spring 37. Bolt body (not available) 38. Extractor 39. Bolt carrier 40. Gas piston 41. Recoil spring cam 42. Recoil spring front guide 43. Recoil spring retainer 44. Recoil spring 45. Upper handguard 46. Upper handguard spring 47. Gas tube 48. Dust cover 49. Rear sight 50. Rear sight catch 51. Sight catch spring 52. Rear sight pin 53. Lower handguard 54. Magazine Lubrication Warning Firing a firearm with oil, grease or any other material even partially obstructing the bore may result in damage to the firearm and injury to the shooter and those nearby. Do not spray or apply lubricants directly on ammunition. If the powder charge of a cartridge is affected by the lubricant, it may not be ignited, but the energy from the primer may be sufficient to push the bullet into the bore where it may become lodged. Firing a subsequent bullet into the obstructed bore will damage the firearm and may cause injury to the shooter and those nearby. Use lubricants properly. You are responsible for the proper care and maintenance of your firearm and ammunition. WARNING! Altering or modifying parts and/or internal safeties is dangerous and will void the warranty. This firearm was manufactured to perform properly with the original parts as designed. It is your duty to make sure any parts you buy are made for this firearm and are installed correctly and that neither the replacements nor originals are altered or changed. Your gun is a complex precision tool with many parts that must relate correctly to other parts in order for proper and safe operation. Putting a gun together wrong or with incorrect or modified parts can result in a damaged gun, danger, and injury or death to you and others through malfunction. Always have a qualified gunsmith work on your gun or at least check any work not performed by a gunsmith. PAP M85 NP Pistol Manual 2013 Century International Arms, Inc. Page 15
16 Limited Parts Replacement Warranty The PAP M85 NP is warranted to be free of manufacturing defects for a period of one year from the original date of purchase of the PAP M85 NP from a federally licensed firearms retailer. The warranty only applies to the first retail purchaser and is not transferrable or assignable. Proof of purchase must be presented at the time any warranty claim is made. This is a one year warranty limited to replacement of improperly manufactured parts. Any alternations, modifications, abuse, misuse or discharge of poor quality, corrosive or defective ammunition voids the warranty. Return Authorization To obtain warranty service, contact us at to get a return authorization. Please that a return authorization must be obtained prior to returning the firearm. Century International Arms, Inc. 236 Bryce Boulevard Fairfax, Vermont USA PAP M85 NP Semi Auto Pistol, Cal. 5.56x45mm (.223) Distributed by: Century International Arms, Inc. 236 Bryce Boulevard, Fairfax, VT Sales Tel: Sales Fax: Manufactured by: Zastava Entire Contents 2013 Century International Arms, Inc. All rights reserved. PAP M85 NP Pistol Manual
Owner s Manual N-PAP & O-PAP M70 SEMI-AUTO RIFLES Cal. 7.62X39MM Congratulations on your purchase of the PAP M70 Semi-Auto Rifle. With proper care and handling, it will give you long, reliable service.
Owner s Manual N-PAP & O-PAP M70 DF SEMI-AUTO RIFLES Cal. 7.62X39MM Congratulations on your purchase of the PAP M70 DF Semi-Auto Rifle. With proper care and handling, it will give you long, reliable service.
Owner s Manual AK63D SEMI-AUTO RIFLE Cal. 7.62X39MM Congratulations on your purchase of the AK63D Semi-Auto Rifle. With proper care and handling, it will give you long, reliable service. The AK63D is a
Owner s Manual WASR TYPE SPORTING RIFLES Cal. 7.62x39MM Congratulations on your purchase of the WASR Rifle. With proper care and handling, it will give you long, reliable service. The WASR is a semi-automatic
Owner s Manual SPM COACH SHOTGUN 12 Ga., 20 Ga. &.410 Ga. Congratulations on your purchase of the SPM Coach Shotgun. With proper care and handling, it will give you long, reliable service. We specifically
CENTURION 39 SPORTER RIFLE Owner s Manual Cal. 7.6x39MM 00% American Made! Congratulations on your purchase of the Centurion 39 Sporter Rifle. With proper care and handling, it will give you long, reliable
Owner s Manual RAS47 SEMI-AUTO RIFLE Cal. 7.62X39MM 100% AMERICAN MADE! Congratulations on your purchase of the 100% American Made RAS47 Semi-Automatic Rifle. With proper care and handling, it will give
Owner s Manual CZ99 PRECISION RIFLES Cal..22LR,.22WMRF &.17HMR Congratulations on your purchase of a CZ99 Precision Rifle. With proper care and handling, it will give you long, reliable service. We specifically
Owner s Manual STERLING TYPE I, TYPE II & TYPE III SEMI-AUTO RIFLES Cal. 9x19MM (TYPE I & TYPE II) Cal. 7.62x25MM (TYPE III) COLEFIRE MAGNUM SEMI-AUTO PISTOL Cal. 7.62x25MM Congratulations on your purchase
Owner s Manual AK SEMI-AUTO RIFLE Cal. 5.45x39MM Congratulations on your purchase of an AK Semi-Auto Rifle. With proper care, maintenance and handling, it will give you long, reliable service. The AK is
Owner s Manual M70 Bolt Action Sporting rifles Calibers.30-06,.270 WIN.,.308 WIN.,.243 WIN.,.300 WIN. MAG., 7mm REM. MAG. Congratulations on your purchase of the M70 bolt action sporting rifle. With proper
Owner s Manual C15 M4 SEMI-AUTO RIFLE Cal. 5.56X45MM (.223) Congratulations on your purchase of the C15 M4 Semi-Auto Rifle. With proper care and handling, it will give you long, reliable service. The C15
Owner s Manual TTC PISTOL Cal. 7.62x25MM TOKAREV Congratulations on your purchase of a TTC Pistol. With proper care, maintenance and handling, it will give you long, reliable service. We specifically disclaim
Made in Germany www.umarexusa.com manual safety extractor slide gas vent hammer trigger lock trigger P22 S guide rod takedown lever slide stop magazine release Cal. 9 mm P.A.K. (Blank Firing) OPERATING
Made in Germany www.umarexusa.com slide gas vent hammer barrel bushing recoil spring plug slide stop trigger safety trigger guard magazine release grip Government 1911 A1 S Cal. 9 mm P.A.K. (Blank Firing)
HERITAGE ROUGH RIDER SINGLE-ACTION BIG-BORE REVOLVER OWNER S INSTRUCTION MANUAL We recommend that you seek instruction in safe fi rearm handling by a competent fi rearms instructor. Remember there is no
MP654K AIR PISTOL INSTRUCTION MANUAL European American Armory Corp. 3855 North U.S. Highway One Cocoa, Florida 32926 (321) 639-4842 This manual was downloaded from www.eaacorp.com E-mail: firstname.lastname@example.org
OWNER S MANUAL SDP compact Read the instructions and warnings in this manual carefully before using this firearm; do not discard this manual. This instruction manual should always accompany this firearm
INSTRUCTION MANUAL CZ 75 TS CZ 75 TS - INSTRUCTION MANUAL Before handling the pistol read this manual carefully and observe the following safety instructions. Improper and careless handling of the pistol
IZH46 AIR PISTOL INSTRUCTION MANUAL European American Armory Corp. 3855 North U.S. Highway One Cocoa, Florida 32927 (407) 639-4842 This manual was downloaded from www.eaacorp.com E-mail: email@example.com
OWNER S MANUAL Instruction Book for: Semi-Automatic Pistol This manual contains operating, care, and maintenance instructions. To assure safe operation, any user of this firearm must read and understand
Bolt Action Rifle Patent No. 7823315 B2 and Patents Pending Note: This manual is only a supplement to your firearm s owner s manual. It only addresses the FLEX System and its accessories. IMPORTANT SAFETY
- SAFETY - FIRST AND FOREMOST FIREARMS ARE DANGEROUS WEAPONS, WHICH CAN CAUSE SERIOUS INJURY OR DEATH. WHEN USING ANY FIREARM, SAFETY MUST BE YOUR FIRST AND CONSTANT CONCERN. READ AND UNDERSTAND THE FOLLOWING
INSTRUCTION MANUAL CZ 75 Champion CZ 75 CHAMPION - INSTRUCTION MANUAL Before handling the pistol read this manual carefully and observe the following safety instructions. Improper and careless handling
Before handling the firearm read this manual carefully and observe the following safety instructions. Improper and careless handling of the firearm could result in accidental discharge and cause injury,
HERITAGE ROUGH RIDER SINGLE-ACTION SMALL-BORE REVOLVER OWNER S INSTRUCTION MANUAL We recommend that you seek instruction in safe firearm handling by a competent firearms instructor. Remember there is no
INSTRUCTION MANUAL CZ 750 Before handling the firearm read this manual carefully and observe the following safety instructions. Improper and careless handling of the firearm could result in unintentional
OPERATOR S MANUAL FOR: Colt Advanced Law Enforcement Carbines LE6940 LE6944 LE6943 LE6945CQB & LE6946CQB COPYRIGHT 2010 COLT DEFENSE LLC ALL RIGHTS RESERVED Information contained in this publication is
INSTRUCTION MANUAL CZ 630/631 Before handling the air rifle read this manual carefully and observe the following safety instructions. Improper and careless handling of the air rifle could result in unintentional
IZH43K (BOUNTY HUNTER II) SIDE BY SIDE COCKING HAMMER SHOTGUN WARNING AND INSTRUCTION MANUAL European American Armory Corp. 3855 North U.S. Highway One Cocoa, Florida 32927 (407) 639-4842 This manual was
CK S EARMS MONDBACK FIREARMS MONDBACK EARMS NDBACK DBACK Safety and Handling Instructions K MS BACK WARNING! Please read this owner s manual before taking your new DIAMONDBACK FIREARMS rifle out of the
PA 3-1 CHROME SHOTGUN USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THE FIREARM. SEPTEMBER 2016 ROCK ISLAND ARMORY USER S MANUAL PA 3-1 CHROME
WARNINGS: Carry out safety check before handling the weapon. The weapon is heavily oiled for shipping. Clean and lubricate before firing. These procedures given apply only to the US Ordnance QCB version.
KEL-TEC PLR-16 Pistol SAFETY, INSTRUCTION & PARTS MANUAL STATEMENT OF LIABILITY This pistol may be classified as a dangerous weapon and is surrendered by KEL-TEC CNC INDUSTRIES INC. with the understanding
MODEL Beretta 92FS Caliber.177 (4.5 mm) Pellet CO 2 Air Pistol Operating instructions 3-15 CONTT 1 Safety instructions 2 Description of Parts 3 Operation WARNING: NOT A TOY. ADULT SUPERVISION REQUIRED.
Models 10/110 (excluding LE SERIES ), 11/111, 14/114 and 16/116 Bolt Action Centerfire Rifles Download a QR Code reader application for your Smartphone and then snap this to complete your WARRANTY REGISTRATION
Weatherby SIDE-BY-SIDE SHOTGUN OWNER'S MANUAL WEATHERBY is a registered trademark of Weatherby, Inc TEN COMMANDMENTS OF FIREARMS SAFETY Prevention is the solution to hunting and shooting casualties. Every
Owner s Owner s Manual for: Remington Premier Over and Under Shotgun Manual IMPORTANT! READ ALL WARNINGS AND INSTRUCTIONS IN THIS MANUAL BEFORE USING THIS SHOTGUN PAGE 2...THE TEN COMMANDMENTS OF FIREARM
Table of Contents iii Disassembly, Assembly, and Cleaning of M16A4/M4 By: George Carter Chris Talbott Jeremy Tinker Table of Contents Introduction... vii Disassembly... 3 Clearing the Magazine... 3 Retaining
INSTRUCTION MANUAL FOR MAGNUM S BFR Biggest Finest Revolver STAINLESS STEEL SINGLE ACTION REVOLVER * Shown with optional Hogue grip and Millett adjustable rear sight. READ THE INSTRUCTIONS AND WARNINGS
TM OWNER S MANUAL 817 BOLT ACTION.17 HMR BOLT ACTION RIFLE WITH DETACHABLE MAGAZINE IMPORTANT SAFETY WARNINGS NOTE THE SYMBOL: THESE SAFETY WARNINGS ARE FOR YOUR PROTECTION AS WELL AS THE SAFETY OF OTHERS.
MECH-TECH SYSTEMS CCU MODEL FOR GLOCK PISTOLS Operation & Maintenance Manual Read and understand this manual before attempting to use this product. If you have any questions call: 1-866-433-2122 www.mechtechsys.com
USER'S MANUAL AZUR Barrel Hinge pin Barrel lugs Chamber Top lever Muzzle Safety Forearm lug Forearm latch Forearm Forearm iron Receiver Trigger Buttstock IT IS YOUR RESPONSABILITY FAILURE TO HEED ANY OF
OWNER S MANUAL 464 LEVER ACTION CENTERFIRE LEVER ACTION RIFLE IMPORTANT SAFETY WARNINGS NOTE THE SYMBOL: THESE SAFETY WARNINGS ARE FOR YOUR PROTECTION AS WELL AS THE SAFETY OF OTHERS. DISREGARDING INFORMATION
Before handling the pistol read this manual carefully and observe the following safety instructions. Improper and careless handling of the pistol could result in unintentional discharge and could cause
SIGM400 OWNERS MANUAL: HANDLING & SAFETY INSTRUCTIONS READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM; DO NOT DISCARD THIS MANUAL. This instruction manual should always
VANGUARD SERIES 2 OWNERS MANUAL INTRODUCTION Thank you for buying a Weatherby firearm, and welcome to the family. We realize that you had many products to choose from and hope you feel as we do, that you
OWNER S MANUAL 464 LEVER ACTION CENTERFIRE LEVER ACTION RIFLE IMPORTANT SAFETY WARNINGS NOTE THE SYMBOL: THESE SAFETY WARNINGS ARE FOR YOUR PROTECTION AS WELL AS THE SAFETY OF OTHERS. DISREGARDING INFORMATION
S40 OVER UNDER SHOTGUN USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THE FIREARM. SEPTEMBER 2016 ROCK ISLAND ARMORY USER S MANUAL S40 OVER UNDER
Review Questions Chapter 11 Small Arms Weapons 1. On an M16 rifle, where is the magazine release button located? 1. Right side of the weapon, top front of the trigger guard 2. Right side of the weapon,
AR15 SEMI AUTOMATIC INSTRUCTION/ SAFETY MANUAL CAUTION: USE ONLY CLEAN, DRY, ORIGINAL, HIGH QUALITY COMMERCIALLY MANUFACTURED AMMUNITION IN GOOD CONDITON which is appropriate to the caliber of your firearm.
OWNER S MANUAL FOR THE SSi-ONE SINGLE SHOT BREAK ACTION INTERCHANGEABLE RIFLE/SHOTGUN IMPORTANT SAFETY WARNINGS NOTE THE SYMBOL These safety warnings are for your protection as well as the safety of others.
T/C Patriot Use & Loading Supplement Suggested Black Powder & Pyrodex Loads For The T/C Patriot Note: This Model is Out of Production. For Reference Use Only. Muzzleloading Pistol Only Read and Understand
SIG SAUER ENHANCED AUTO MIL SPEC TRIGGER KIT INSTALLATION INSTRUCTIONS 1.0 Warnings 2 www.sigsauer.com This SIG SAUER Enhanced Mil-Spec Auto Trigger Kit comes complete with all parts and detailed installation
ITEM NO. 3500 FULL METAL M4 COBRA ASSAULT RIFLE HANDLING & INSTRUCTIONS MANUAL ignite-blackops.com Manufactured & Distributed by 2012 Bear River International, LLC Logan, UT 84321 All Rights Reserved MADE
DIAMONDBACK FIREARMS Safety and Handling Instructions.380 AUTO PISTOL CK S EARMS IAMONDBACK CK FIREARMS DIAMONDBACK FIREARMS MONDBACK NDBACK EARMS ONDBACK RMS DBACK MS ACK K WARNING! Please read this owner
1911RAC Quick Guide - 8x11- Final 12-16-13.qxp_Layout 3 1/6/14 9:45 AM Page 1 Quick Reference Instructions Model 1911RAC Autoloading CO 2 Operated BB Air Pistol PICTURE 1 This picture shows the main parts
OWNER S MANUAL MODEL 695 BOLT ACTION SLUG SHOTGUN IMPORTANT SAFETY WARNINGS NOTE THE SYMBOL These safety warnings are for your protection as well as the safety of others. Disregarding information in this
Owner s Manual Instruction Book for: Model 105 CTi Autoloading Shotguns IMPORT ANT! READ ALL INSTRUCTIONS AND WARNINGS IN THIS BOOK BEFORE USING THE FIREARM. Some Illustrations May Depict Cosmetic Differences
KEL-TEC P-3AT PISTOL KEL-TEC CNC INDUSTRIES INC. PO BOX 236009 COCOA FL 32926 321-631-0068 www.kel-tec.com OWNED MADE PARTS SAFETY, INSTRUCTION, AND PARTS MANUAL KEL-TEC P-3AT PISTOL SAFETY, INSTRUCTION,
Owner s Manual Manual Instruction Book for: Models 700, Seven, & 673 Bolt action centerfire rifles page 2...the ten commandments of firearm safety IMPORTANT! page 7...important parts of the firearm READ
TABLE OF CONTENTS A. Safety Information and Warnings... 2 B. Overview Description... 4 Nomenclature... 4 Specifications... 4 Ammunition... 5 Sling Mounting... 5 C. Operating Instructions Safety... 6 Loading
BUCK MARK RIFLE AUTOLOADING RIFLE OWNER S MANUAL Important operating instructions for: BROWNING BUCK MARK AUTOLOADING RIFLE If you have any questions about your new firearm, this owner s manual or other
OWNER S MANUAL 20 GAUGE AUTOLOADING SHOTGUN IMPORTANT SAFETY WARNINGS NOTE THE SYMBOL THESE SAFETY WARNINGS ARE FOR YOUR PROTECTION AS WELL AS THE SAFETY OF OTHERS. DISREGARDING INFORMATION IN THIS MANUAL
IMPORTANT SUPPLEMENTAL INSTRUCTIONS FOR WINCHESTER MODEL 1895 TAKEDOWN LEVER-ACTION RIFLE These are special instructions for the Winchester Model 1895 Takedown Rifle only. These instructions must be used
Before handling the firearm read this manual carefully and observe the following safety instructions. Improper and careless handling of the firearm could result in accidental discharge and cause injury,
C1, FM 23-65 * CHAPTER 3 OPERATION AND FUNCTIONING This chapter explains the operation of the MG. It discusses the loading, unloading, and clearing procedures, and the cycle of functioning of the weapon.
PCP PELLET RIFLE Cal. 4,5 mm (.177) Cal. 5,5 mm (.22) Operating instructions 2-9 WARNING: NOT A TOY. THIS AIRGUN IS DESIGNED FOR USE BY EXPERIENCED SHOOTERS 18 YEARS OF AGE OR OLDER AND IS INTENDED FOR
82A1 Model 82A1 OPERATOR S MANUAL TABLE OF CONTENTS 2 2 3 3 5 6 7 7 7 8 8 10 14 17 18 19 20 21 23 24 28 32 MANUFACTURER S DISCLAIMER WARRANTY AND SERVICE USE OF THIS MANUAL SAFETY GUIDELINES DESCRIPTION
CK S EARMS MONDBACK FIREARMS MONDBACK EARMS NDBACK DBACK Safety and Handling Instructions K MS BACK WARNING! Please read this owner s manual before taking your new DIAMONDBACK FIREARMS pistol out of the
This is the primary rule of gun safety. A safe direction means that the gun is pointed so that even if it were to go off it would not cause injury or damage. The key to this rule is to control where the
VR1 Owner s Manual Vigilance Rifles, Inc. 1653 Plum Lane Redlands, CA 92374 P 909.307.8877 F 909.307.8866 www.vigilancerifles.com INTRODUCTION: Vigilance Rifles offers a new line of Semi-Automatic Rifles
1 GUN SAFETY RULES Observe these rules of safe gun handling. 1. Always keep the muzzle pointed in a safe direction. Watch the muzzle at all time: never point a gun, accidentally or intentionally, at any
INSTRUCTIONS FOR USE! WARNING READ THIS MANUAL CAREFULLY BEFORE LOADING OR USING YOUR GLOCK PISTOL.! WARNING LIKE MOST MODERN HANDGUNS YOUR GLOCK PISTOL IS DESIGNED WITHOUT A CONVENTIONAL MANUAL SAFETY.
Monster Windy City Leopard User instruction manual Windy City Monster Leopard Fill pressure: 200 bar (approximately 2,900 psi) Contents Rules of safe shooting... 3 Filling the rifle... 4 Loading the rifle...
Springfield Armory OPERATION AND SAFETY MANUAL Important Safety Information Inside Read this manual completely before handling this firearm. This manual is for SPRINGFIELD ARMORY SAINT FIREARMS ONLY. Keep
FX4 SEMI-AUTOMATIC SHOTGUN INSTRUCTION MANUAL READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM Contents OWNER'S MANUAL... 1 IMPORTANT SAFETY WARNINGS... 1 Congratulations!...
BUCK MARK PISTOL OWNER S MANUAL SUPPRESSOR READY Important operating instructions for: BROWNING BUCK MARK AUTOLOADING PISTOL If you have any questions or comments regarding your new firearm, please contact
TM 9-005-239-0 WARNING SUMMARY Treat every firearm as if it were loaded. Never accept or take over a firearm from another until you have checked personally to see that it is unloaded or in a completely
BDA 380 PISTOL OWNER S MANUAL THANK YOU FOR CHOOSING A BROWNING BDA 380 PISTOL The Browning BDA 380 is another in a long line of dependable, high-quality Browning centerfire pistols you will be proud to