Operators Manual. To Order Parts Call Stripping Solution Recovery Vacuum

Size: px

Start display at page:

Download "Operators Manual. To Order Parts Call Stripping Solution Recovery Vacuum"

Arline Waters
5 years ago
Views:

1 Operators Manual Stripping Solution Recovery Vacuum READ OPERATORS MANUAL BEFORE OPERATING

2 Date of Purchase Purchased From Record this Important Information Address City State Zip Phone Serial Number Medical Emergency Police Fire Contact Emergency Contacts

3 Safe Operating Procedures Machine Specifications Operating Instructions Vacuuming Stopping Draining Adjusting Squeegee Angle Using Optional Squeegee Attachment Maintenance Instructions Removing / Attaching Squeegee Blades Removing / Attaching Squeegee Cleaning Battery Maintenance Connecting the Batteries and Vacuum Motor Battery Charging Refilling the Battery with Distilled Water Measuring the Specific Gravity of Battery Electrolyte Balanced Battery Charging Battery Replacement Machine Exploded View Drawings and Parts Lists Table of Contents Wiring Diagram Squeegee Assembly Lift Assembly Frame Assembly Tank Assembly Float Assembly Final Assembly Warranty

4 Safe Operating Procedures Safe Operating Procedures: Use care when transporting machine with a full tank. Do not raise filled tank to check batteries. Thoroughly clean exterior, tank, hoses, and squeegee after each use. Do not use the machine as a dry vac, it is only intended for stripper, cleaning solutions, and water. Always use appropriate safety gear when dumping stripper. Obey all applicable laws for the disposal of stripper. When the recovery tank reaches capacity, an overfill valve will seal the vacuum motor port. Do not attempt to operate the machine after the vacuum motor port has been sealed. Do not overtighten retaining knobs on squeegee. Knobs should be tightened enough to hold the squeegee in place while allowing it to break away if struck. To reduce foaming, add defoamer in tank before vacuuming stripper. Turn off the vacuum motor when tank reaches capacity and closes the vacuum motor port. Machine Specifications Height: 44 (111,8 cm) Width: 26 (66 cm) Length: 39 (99,1 cm) Squeegee length: 26 (66 cm) or 34 (86 cm) Weight: 225 lb (102 kg) w/batteries, 130 lb (59 kg) w/out batteries 24V system 25A switch / breaker 120A charger plug Tank Capacity Standard Model: 30 gal. (113,6 l) Tank Capacity Low-Profile Model: 16.5 gal. (62,5 l) Battery Compartment dimensions: x x 10 (41.48 cm x cm x 25.4 cm) Battery dimensions: 8.13 x 6.63 x 12 (20.65 cm x cm x cm) Hand-arm vibration: 0.5 mm/sec 2 Overall sound level: 74 db(a) 2

5 Operating Instructions Vacuuming 1. Make sure tank lid is closed, all hoses are properly connected, and hose plug is inserted in the dump hose. 2. Lower the squeegee by pushing slightly down and forward on the foot pedal and allowing it to rise slowly. 3. Turn on the vacuum motor switch. 4. Walk forward slowly, allowing the machine to vacuum up the solution on the floor. NOTE: The machine is intended to operate only with the squeegee moving forward. 5. To prolong squeegee life, raise the squeegee by pushing the foot pedal down and slightly back to lock in place when pulling the machine backwards. CAUTION: Floors will be very slippery when wet, especially when wet with stripping solution! Stopping 1. Stop the machine s movement for approximately two seconds. 2. Raise the squeegee by pushing the foot pedal down and slightly back to lock in place. 3. Turn off the vacuum motor. Draining 1. Place the StripVac in an appropriate area for draining. 2. Remove the dump hose from the spring hose clip at the rear of the machine. 3. Unplug hose plug from dump hose and lower to drain. Adjusting Squeegee Angle 1. The squeegee angle may be adjusted by turning the adjustment knob until the desired angle is obtained. Using Optional Squeegee Attachment 1. Disconnect the suction hose from the elbow on the front of the tank. 2. Connect the optional vacuum wand to the elbow on the front of the tank. 3. Turn on the vacuum motor. 4. Push or pull the optional vacuum wand to vacuum fluids in hard to reach areas. 5. When finished, turn off the vacuum motor and reconnect the suction hose. 3

6 Maintenance Instructions Removing / Attaching Squeegee Blades Front Squeegee Blade: 1. With the vacuum motor off, remove the front blade by loosening the front seven wing nuts and removing the front squeegee retainer strap. 2. As the squeegee wears, it may be flipped 180 to have a new wear edge come in contact with the floor. NOTE: The ribs on the front squeegee must be facing forward. 3. To reattach, place the front blade on the squeegee, followed by the front squeegee retainer strap, and the front seven wing nuts. Rear Squeegee and Backer Blades: 1. With the vacuum motor off, remove the rear squeegee and backer blades by loosening the rear seven wing nuts and removing the rear squeegee retainer strap. NOTE: The rear squeegee and backer blades are identical. The rear blade is to be positioned so that the squeegee blade attachment set screws are at the top of the slot in the blade. The backer blade is to be positioned so that the screws are at the bottom of the slot in the blade. This enables the rear blade to come in contact with the floor and backer blade to provide support. 2. As the rear squeegee blade wears, it may be reoriented so that all four edges of the blade come in contact with the floor. After all four edges are worn out, switch the rear squeegee blade with the backer blade and repeat the process. This enables a total of eight working edges to be used before replacing blades. 3. To reattach, place the rear squeegee and backer blades on the squeegee. Then secure the rear squeegee retainer strap with the rear seven wing nuts. Removing / Attaching Squeegee 1. With the vacuum motor off, disconnect the suction hose from the squeegee. 2. Firmly pull the squeegee from the bracket. If needed, slightly loosen the retaining knobs until the squeegee is released. 4

7 Cleaning IMPORTANT! Clean the StripVac after each use. 1. Place the StripVac in an appropriate area for draining. 2. Remove the dump hose from the spring hose clip at the rear of the machine. 3. Unplug hose plug from dump hose and lower to drain. 4. Open the lid on the top of the tank and rinse the inside of the tank with hot water. 5. Rinse out the suction hose (the one at the front of the machine). 6. Rinse the squeegee. 7. Once unit is thoroughly cleaned and drained, plug in the dump hose and attach hose to hose clip. 8. Clean the optional vacuum wand. IMPORTANT! Do not get water in the vacuum hose (the one that is connected to the vacuum motor), or on any electrical components. CAUTION: Do not lift the tank when it contains liquid. NOTE: When lowering the tank to its seated position, use care not to kink or crush hoses. Do not drop the tank into place. Lower the tank gently into position. 5

8 Battery Maintenance Connecting the Batteries and Vacuum Motor 1. Place batteries, B1 and B2, into the chassis as shown. 2. Connect the charger plug positive lead, L1, on the positive post of B1. 3. Connect the positive switch lead, L2, on the positive post of B1. Tighten the wing nut on the positive post of B1. 4. Connect the positive vac motor leads, L3 and L4. 5. Connect the jumper lead, L5, from the negative post of B1 to the positive post of B2 and tighten their respective wing nuts. (Note: The black end of the L5 connects to the negative post of B1 and the red end of L5 connects to the positive post of B2.) 6. Connect the negative vac motor lead, L6 to the negative post of B2. 7. Connect the charger plug negative lead, L7, to the negative post of B2. Tighten the wing nut on the negative post of B2. WARNING: Battery electrolyte is a dangerous fluid. The fluid contains sulfuric acid, which is extremely corrosive. Observe the following precautions to prevent accidents. Make sure that the liquid does not contact your skin or clothing. When carrying the battery, or working in the vicinity of the battery, be sure to wear protective glasses and gloves. If electrolyte comes into contact with your eyes, skin or clothing, take the following actions: Contact with skin or clothing: Wash immediately with large amounts of clean water. Contact with eyes: Wash immediately with large amounts of water for 15 minutes or more. Consult a physician immediately. If electrolyte is swallowed, take the following actions: PROPOSITION 65 WARNING Drink a large amount of water, a milk and egg white Battery posts, terminals, and related accessories mix, or vegetable oil. contain lead and lead compounds, chemicals Consult a physician immediately. known to the State of California to cause cancer and reproductive harm. Wash hands after handling. 6

9 Battery Charging Observe the following for your safety when working with the battery charger: Make sure the power is OFF. Be sure to use the specified battery charger. Connect the battery charger s power plug only to a 115V/60 Hz 3-wire grounded power supply (220V/50 Hz European). Recharge in a well-ventilated area. Recharge only away from flames. Do not attempt recharging with wet hands. During recharging, place the battery charger in a flat, dry area, or on a safety stand. When removing the battery charger power cord or the charger cord from the outlet on the machine, do so by pulling the plug, not the cord. Check the battery charger power cord and charge cord in advance. Do not use a damaged cord. Stop recharging if the battery electrolyte temperature is 120 F (50 C) or more. Store the batteries and electrolyte in a place that is out of reach of children. WARNING: Be sure to connect the battery charger power plug to a 3-wire, grounded, 115V/60Hz outlet only (220V/50 Hz European). Charging Procedure 1. Switch OFF the machine power switch. 2. Park the floor machine in a safe, flat area. 3. Switch the battery charger power switch OFF. 4. Insert the battery charger charge plug into the machine s charge socket. 5. Insert the battery charger power plug into the specified outlet. 6. Switch the battery charger ON. CAUTION: The battery charger is designed so that charging of batteries is not possible if the voltage level has dropped below a certain value. Under these circumstances, the battery charger charge lamp will not light. During charging, do not turn the machine power switch ON. 7. When a certain battery charge level is reached, the battery charger timer lamp lights. After about 3 hours, the time lamp starts blinking to indicate that charger output has stopped. 8. Check that the timer lamp is blinking, and switch OFF the battery charger power. 9. Remove the charger power plug from the main outlet by the plug. Do not pull on the cord. 10. Remove the charger cord from the charge socket by the plug. Do not pull on the cord. 11. Charging is now complete, and you can operate the machine. Keep the battery charger in a dry place. Do not store in an area where the floor is wet. 7

10 Refilling the Battery with Distilled Water NOTE: If the battery terminals are dirty, wipe clean with a dry cloth, and apply some mineral grease. 1. Switch the power OFF. 2. Drain the recovery tank completely. 3. Lift the tank unit. 4. Check the liquid level. If the electrolyte is between the UPPER LEVEL and LOWER LEVEL, refilling is not necessary. Refill if below the LOWER LEVEL. Remove the cell plugs from the batteries and fill each with distilled water to the UPPER LEVEL. Do not exceed this level. Replace all plugs and tighten. 5. Gently lower the tank unit. Measuring the Specific Gravity of Battery Electrolyte 1. Switch OFF the power. 2. Drain the tank completely. 3. Lift the tank unit. 4. Remove the cell plugs from the battery. Measure the specific gravity of two (2) of the battery cells on each battery with a hygrometer. Check the specific gravity and state of battery charge using the table below. 8 Fully charged Charging required 68 F (20 C) 68 F (20 C) > Replace the cell plugs and tighten firmly. 6. Gently lower the tank unit. Balanced Battery Charging Balanced charging is carried out to correct the imbalance between two batteries which may be over- or undercharged, and improve battery life. This procedure should be carried out once a month. 1. Charge batteries. 2. Switch the battery charger ON. The charge lamp lights up. Continue charging until the timer light starts blinking again. 3. Check that the battery charger timer lamp is blinking, and carry out the procedure outlined in Battery Charging.

11 Battery Replacement CAUTION: Use only batteries supplied by Pioneer Eclipse. 1. Switch OFF the power switch. 2. Drain recovery tank. 3. Park the machine in a safe, flat area. 4. Raise the tank unit. 5. Unplug the batteries from the machine. Take hold of both connectors to remove. Do not pull on the cable. 6. Remove the connection cable from the battery terminals (first the negative terminal, then the positive.) Be careful not to ground the wrench on the metal frame. 7. Remove the batteries, firmly gripping with both hands. Place the batteries carefully on the floor. 8. Place new batteries in the correct positions in the battery tray. Hold each battery firmly with both hands and install it gently in the tray. 9. Connect the two cables to the new batteries terminals as shown in Connecting the Batteries and Vacuum Motor. Make sure that you are connecting it in the correct way. First, connect a cable to the positive terminal, and then to the negative terminal. 10. Plug into connection firmly. 11. Lower the recovery tank carefully. 9

12 This page intentionally blank. 10

13 Wiring Diagram Machine Drawings & Parts Lists REF. PART # DESCRIPTION QTY. STRIPVAC WIRING DIAGRAM - MP SS1012 BATTERY, 12V MP CONNECTOR, S4120 W/6 GA CONTACTS MP MOTOR, VACUUM, 24V, 3 STAGE MP SWITCH, 25A MP WIRE, PLUG, CHARGER, POS MP WIRE, PLUG, CHARGER, NEG MP WIRE, CORD MP WIRE, VACUUM, NEG MP WIRE, 10 GA, BLACK, JUMPER MP WIRE, VACUUM 1 11

14 StripVac Squeegee Assembly 12

15 REF. PART # DESCRIPTION QTY. STRIPVAC 26 SQUEEGEE ASM. - MP MODELS SV2026, SV2026E, SV3026E 101 RV KNOB, HANDLE NB BOLT, SOCKET, 3/8-16 X 1-1/2, SS MP KNOB, HANDLE, ASSEMBLY MP WHEEL, 3, PERFORMA, FLAT TREAD NB BOLT, HEX, 5/16-18 X 1-1/2, SS NB WASHER, FLAT, 5/16, SS NB WASHER, FLAT, FENDER, 3/8, SS NB WASHER, WAVE, ID 1-1/4 X OD 1-5/8, SS NB WASHER, FLAT, 1/2, SS NB NUT, WING, 1/4-20, SS NB SCREW, SET, 1/4-20 X 1 SS MP SQUEEGEE, ALUMINUM MP SQUEEGEE, BLADE, FRONT MP SQUEEGEE, BLADE, REAR MP STRAP, RETAINER, SQUEEGEE MP NIPPLE, 1-1/4 O.D. 1 STRIPVAC 34 SQUEEGEE ASM. - MP MODELS SV3034, SV3034E, SV2034E 101 RV KNOB, HANDLE NB BOLT, SOCKET, 3/8-16 X 1-1/2, SS MP KNOB, HANDLE, ASSEMBLY MP WHEEL, 3, PERFORMA, FLAT TREAD NB BOLT, HEX, 5/16-18 X 1-1/2, SS NB WASHER, FLAT, 5/16, SS NB WASHER, FLAT, FENDER, 3/8, SS NB WASHER, FLAT, 1/2, SS MP KNOB, FLUTED, 1/4-20 X 1 STUD MP SQUEEGEE, RUBBER, GUM, TAN, FRONT MP BAND, FRONT, SQUEEGEE, 34 WELD MP SQUEEGEE, 34, WELDMENT MP SQUEEGEE, RUBBER, GUM, TAN, REAR MP BAND, REAR, SQUEEGEE, 34, LEFT, WELD MP BAND, REAR, SQUEEGEE, 34, RIGHT, WELD MP LATCH, DRAW HANDLE NB RIVET, POP, 1/8 X 5/ MP KEEPER, HOOK, EXPOSED 1 StripVac Squeegee Assembly Parts List 13

16 StripVac Lift Assembly

17 34 SQUEEGEE LIFT BEFORE SERIAL # STRIPVAC LIFT ASSEMBLY W/26 SQUEEGEE - MP REF. PART # DESCRIPTION QTY. 201 MP BRACKET, BREAK-AWAY MP PEDAL, FOOT, WELDMENT MP ARM, LIFT, WELDMENT MP BRACKET, ADJUSTMENT, SQUEEGEE NB PIN, CLEVIS, 3/8 X 3/4, SS NB PIN, PRESTO, 3/32 X 1-5/8, SS (24, 48 models) 7 (low profile models) MP PIN, LIFT, 1/2 X 8 7/ NB BEARING, I-GLIDE, 3/8 ID X 3/ NB BOLT, HEX, 1/4-20 X 1, SS NB NUT, LOCK, 1/4 SS NB WASHER, FLAT, 1/4, SS NB PIN, CLEVIS, 1/2 X 2, SS MP BUSHING, PIVOT NB WASHER, FLAT, 1/2, NYLON RV KNOB, 3/ NB BOLT, 3/18-16 X 3-1/2 CARRIAGE, SS NB NUT, HEX, 3/8-16, SS NB PIN, CLEVIS, 1/4 X 3/4, SS (24, 48 models) 2 (low profile models) NB PIN, COTTER, 3/32 X 1, SS MP TREAD, PEDAL, NON-SLIP MP BRACKET, BREAK-AWAY, SQ. 34 WELD NB NUT, JAM, 1/2-20 UNF MP KNOB, LOCK, KNURLED MP NUT, JAM, 1/2-20 UNF, KNURLED MP CASTER, SWIVEL, 1-5/8 DIA. W/STUD 2 StripVac Lift Assembly Parts List STRIPVAC LIFT ASSEMBLY W/34 SQUEEGEE REF. PART # DESCRIPTION QTY. 201 MP BRACKET, ADJUSTMENT, ROLLER, WELD NB WASHER, FLAT, NARROW, 1/ NB NUT, LOCK, 1/ MP BRACKET, CASTER, SQUEEGEE 34, WELD NB PIN, CLEVIS, 3/8 X 3/4, SS NB BOLT, CARRIAGE, 5/16-18 X 1, SS MP CASTER, 2 1/2, REAR, 3/4, STEM NB BERAING, IGLIDE 3/8 ID X 3/16 PANEL NB WASHER, FLAT, 5/16, SS NB NUT, LOCK, 5/16, SS MP BRACKET, BREAKAWAY, SQUEEGEE, NB PIN, PRESTO, 3/32 x 1 5/8, SS NB BOLT, CARRIAGE, 3/8-16 X 3 1/2, SS NB NUT, HEX, 3/8-16, SS RV KNOB, HANDLE 1 15

18 StripVac Frame Assembly 16

19 REF. PART # DESCRIPTION QTY. STRIPVAC FRAME ASSEMBLY - SV MP CHASSIS, HYDROSTAR/ STRIPVAC MP WELDMENT, BUSHINGS, LIFT NB BOLT, HEX, 3/8-16 X 5/ NB WASHER, FLAT, 3/8, SS MP CASTER, 4, COLSON NB BOLTS, HEX, 5/16-18 X 1, SS NB BOLTS, CARRIAGE, 5/16-18 X 1, SS NB NUT, LOCK, 5/16, SS NB WASHER, FLAT, 5/16, SS NB WASHER, LOCK, 5/16, SS MP WHEEL, MP HANDLE, STRIPVAC (STANDARD MODEL) 1 MP HANDLE, STRIPVAC, LOW-PROFILE, ASM MP BRACKET, MOUNT, CHARGER NB NUT, HEX, 3/8-16, SS NB WASHER, LOCK, 3/8, SS MP PLATE, MOUNT, HANDLE, WELDMENT MP PLATE, SUPPORT, TANK, WELDMENT (24, 48 models) 1 MP PLATE, SUPPORT, TANK, WELDMENT (low profile models) NB BOLT, 5/16-18 X 5/8, SS NB ROLLER, PIVOT, TANK MP HINGE, LH 1 StripVac Frame Assembly Parts List REF. PART # DESCRIPTION QTY. 321 MP HINGE, RH NB BOLT, PAN HD, 5/16-18 X 5/8 SS MP MOTOR, VACUUM, 3-STAGE, 24 V1 324 NB BOLT, HEX, 1/4-20 X 1-1/2, SS NB NUT, LOCK, 1/4, SS NB WASHER, FLAT, 1/4, SS MP SWITCH, BREAKER, 24V, 25A, ROCKER MP HOUSING, SWITCH (MODIFIED) HAP8026 CONNECTOR, SY120 W/6 GA. CONTACTS NB NUT, LOCK, #6, SS NB BOLT, #6-32 X 1 PAN HEAD, SS NB WASHER, FLAT, #6, SS NB4381 SCREW, DRILL KWIK, #8 X 3/4, SS MP CLIP, SPRING, HOSE MP HEYCO, RELIEF, STRAIN, 5/ NB BOLT, STRIPPER, 3/8 X 5/16-18 X 1/2, SS MP BOOT, COVER, SWITCH NB WASHER, FLAT, #10, SS MP BRACKET, SUPPORT, WELD 4 (2 EACH SIDE) 340 NB BUSHING, 1/2 OD X 0.41 ID X 0.96 L MP BUSHING, ADAPTER, WHEEL 2 17

20 StripVac Tank Assembly

21 REF. PART # DESCRIPTION QTY. STRIPVAC TANK ASSEMBLY - SV TANK, RECOVERY, STRIPVAC, W/TRAY, ASM. 401 SV TANK, RECOVERY, STRIPVAC, TRIMMED PS BRACKET, DIFFUSION, TANK, REC MP DOME, TANK, STRIPVAC, ASM NB BOLTS, HEX, 5/16-18 X 1, SS NB WASHER, 5/16, BONDED NEOPRENE NB9505 WASHER, FLAT, 5/16 X 1-1/ NB3265 NUT, LOCK, 5/16-18 NC NB9515 SCREW, PAN HD, 6-32 X 1/ NB WASHER, FLAT, #6, SS NB BOLT, 5/16-18 X 5/8, SS NB WASHER, FLAT, 5/16, SS NB WASHER, LOCK, 5/16, SS MP BRACKET, LIFT, TANK MP FITTING, BULKHEAD, 1-1/2 PVC MP FITTING, 90 DEG. ELBOW, 1-1/2 PVC MP FITTING, BULKHEAD, 1-1/2 MODIFIED MP HANDLE, LIFT NB SCREW, PHILLIPS, PAN HD, 1/4-20 X MP VALVE, FLOAT, ASSEMBLY MP PLATE, DEFLECTOR NB NUT, LOCK, #6-32, SS NB WASHER, LOCK, 1/4, SS NB WASHER, FLAT, 1/4, SS 2 StripVac Tank Assembly Parts List

22 StripVac Float Assembly 20

23 REF. PART # DESCRIPTION QTY. STRIPVAC FLOAT VALVE ASSEMBLY - MP MP BRACKET, PIVOT, VALVE MP PLATE, VALVE, FLOAT, WELDMENT MP FLOAT, BALL MP GASKET, VALVE, FLOAT NB BOLT, HEX, 1/4-20 X 1, SS NB WASHER, LOCK, 1/4, SS NB WASHER, FLAT, 1/4, SS NB WASHER, FENDER, 1/4 X 1 OD, SS NB NUT, LOCK, 1/4, SS 3 StripVac Float Assembly Parts List 21

24 StripVac Final Assembly 22

25 REF. PART # DESCRIPTION QTY. STRIPVAC FINAL ASSEMBLY - SV NB WASHER, FLAT, 1/2, NYLON MP HOSE, VACUUM (STD MODEL) 1 MP HOSE, VACUUM, LOW-PROFILE MP HOSE, SUCTION (STD MODEL) 1 MP HOSE, SUCTION, LOW-PROFILE MP HOSE, DUMP, 36 1 MP HOSE, DUMP, LOW-PROFILE NB CLAMP, HOSE, WORM GEAR, 1-3/4, SS MP ARM, CATCH NB PIN, CLEVIS, 3/8 DIA., 4 3/ NB PIN, PRESTO, 3/32 X 1-5/8, SS (24, 48 models) 1 NB COTTER PIN 3/32 X 1 SS (low profile models) TA039 PLUG, HOSE 40 mm SV TANK, ASM. (STD MODEL) 1 SV TANK, STRIPVAC, LOW-PROFILE, ASM SV FRAME, STRIPVAC, ASM. (STD MODEL) 1 SV FRAME, STRIPVAC, LOW-PROFILE, ASM MP LIFT, SQUEEGEE, 26, ASM MP SQUEEGEE, 26, ASM SV HOSE, 10 X 1 1/2, GREY W/ SWIVEL CUFF SV WAND, 54, GREY ABS SV SQUEEGEE, 14 DOUBLE BLADED, GREY ABS SV3026-VK KIT, WAND, STRIPVAC MP SQUEEGEE, 24, ASM 1 StripVac Final Assembly Parts List 23

26 LIMITED WARRANTY STRIPVAC TO QUALIFY FOR THIS WARRANTY: 1) Machine must be registered at the time of purchase on a form provided by Pioneer Eclipse Corporation. Your Pioneer Eclipse Distributor is responsible for the registration of your machine. Please cooperate with your distributor in supplying necessary information on the card. 2) The machine must have been purchased from Pioneer Eclipse or an authorized Pioneer Eclipse Distributor. 3) This warranty extends to the original purchaser only and is not transferable to subsequent owners. TIME PERIODS ONE (1) YEAR PARTS AND LABOR - Warranted for the forementioned time periods to be free from defects in material and workmanship from the date of purchase by the original owners. (See Exclusions.) EXCLUSIONS (Not Covered by Warranty) 1) Parts that fail through normal wear by reason of their characteristics (pads, brushes, belts, bumpers, skirting, or other consumable parts). 2) This warranty does not extend to parts affected by misuse, neglect, abuse or improper maintenance. All defective parts must be returned to the Distributor for credit. 3) Motors warranted by motor manufacturer. THE OBLIGATION OF PIONEER ECLIPSE CORPORATION 1) The obligation of Pioneer Eclipse under this warranty is limited to repairing or replacing, at its option, any part which is proven to be defective in material or workmanship under normal use for the applicable period stated above. 2) Warranty repairs will be made by your Pioneer Eclipse Distributor without charge for parts and labor. 3) Parts repaired or replaced under this warranty are warranted only during the balance of the original warranty period. All defective parts replaced under these warranties become the property of Pioneer Eclipse. WARRANTY SERVICE To obtain warranty service, take your machine and proof of purchase to any authorized Pioneer Eclipse Distributor, preferably to the distributor from whom the machine was purchased. For the Distributor in your area, call Pioneer Eclipse Customer Service Department at If you are dissatisfied with the service that you receive, call or write Pioneer Eclipse Customer Service Department for further assistance. DISCLAIMER OF CONSEQUENTIAL PIONEER ECLIPSE DISCLAIMS ANY RESPONSIBILITY FOR LOSS OF USER TIME OF THE PIONEER ECLIPSE MACHINE OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGE EXCEPT AS STATED IN THE WARRANTY APPLICABLE TO EACH MACHINE. EXCEPT AS STATED IN SUCH WARRANTIES, THE COMPANY DOES NOT OTHERWISE WARRANTY ANY MACHINE AND NO WARRANTY, EXPRESS, IMPLIED OR STATUTORY IS MADE BY THE COMPANY.

28 P.O. Box 909 Sparta, NC ; Fax: EC Machinery Directive 98/37/EC; Harmonized Standards EN292-1: 1991, EN294: 1992, EN953: 1997, EN60529: 1991, EN292-2: 1991, EN836: 1997, EN1050: LT R,

Parts Manual STRIKER Striker 2840 Parts List - PN Printed in USA 03/18/08

Parts Manual STRIKER Striker 2840 Parts List - PN Printed in USA 03/18/08 Parts Manual STRIKER 2840 Striker 2840 Parts List - PN 238155 - Printed in USA 03/18/08 Standard Parts Recommended General Wear Parts Ref No Part Description Qty Part No 1 Squeegee Hose Assembly