Finite Element Modal Analysis of Twin Ball Screw Driving Linear Guide Feed Unit Table

Size: px
Start display at page:

Download "Finite Element Modal Analysis of Twin Ball Screw Driving Linear Guide Feed Unit Table"

Transcription

1 rd International Conference on Mechanical, Industrial, and Manufacturing Engineering (MIME 2016) ISBN: Finite Element Modal Analysis of Twin Ball Screw Driving Linear Guide Feed Unit Table Xiangrong Xu, Xianchun Song, Hongkui Jiang, Yanfeng Li, Qunpeng Lu School of Mechanical and Electronic Engineering, Shandong Jianzhu University, Jinan,Shandong Province, P. R. China ABSTRACT: Twin ball screw driving linear feed system has good vibration resistance, high stiffness and fast system response, etc., can effectively decline vibration of NC machine tools generated in the case of high speed and high acceleration and deceleration, so it is used widely in the high-speed and high-precision NC machine tools. This article is focused on the completion of the finite element modal analysis of twin ball screw driving linear guide feed unit table. The modal of single ball screw driving linear guide feed unit and that of twin ball screw driving linear guide feed unit was analyzed, and the results were compared when nuts are located at the left, middle and right positions of twin ball screw driving linear guide feed unit. The results show that under the same vibration shape, the natural frequencies of twin ball screw driving linear guide feed unit are higher than those of single ball screw driving linear guide feed unit, the twin ball screw driving linear guide feed system has smaller vibration and better dynamic properties; different positions of nuts will affect the natural frequencies of twin ball screw driving linear guide feed unit, smaller in the middle position and larger on two ends, so the vibration on the middle position is larger than that on two ends. 1 INTRODUCTION With the development of high-speed, high-precision and heavy-load NC machine tools,lots of disadvantages of traditional single ball screw driving feed system in high-speed driving process have become more and more obvious,such as big noise,high temperature-rise and low precision. Twin ball screw driving feed system has the advantage of good vibration resistance, high stiffness and fast system response, and can effectively decline vibration of NC machine tools under the condition of high speed and high acceleration. Thus twin ball screw driving feed ststem is becoming more and more widely used in high-speed and high-precision NC machine tools. There are many literatures about the research on twin ball screw driving feed system.in such countries as the United States, Japan, Germany,etc., the technology in this field is relatively developed.but it is difficult to find the relative literatures because of technical security. He Wangyong et al. analyzed the coupling relationship between the loads and the axial and torsional coupling relationship between ball screw and nut of twin ball screw synchronous driving shaft[1]. Yang yong investigated the influence of drive at center of gravity and linear guide joint surface parameters on the dynamic performance of machine tool[2]. Zhou Yong established the finite element model of twin ball screw drive, analyzed its 11 dynamic characteristics, and verified the advantage of dual drive relative to the single drive[3]. Huang Xiaoyan used the finite element simulation software ANSYS Workbench to analyze the dynamic and static characteristics of a high-speed horizontal boring and milling machining center driven at center of gravity[4]. Ding Xihe et al. carried on dynamic characteristic analysis of twin ball screw driving feed system of NC machine tool under the different ball screw and guide span and found the influence law of different ball screw and guide span on the dynamic characteristics of a feed system[5]. Wang Renche et al. researched the influence of the position of center of gravity, the position of nut and the quality of the table on the natural frequency of feed system[6]. But the studies all above seldom included the support guide into the feed system. In this paper, considering the influence of the support guide, twin ball screw drive linear guide feed unit table is designed, and using ANSYS method, the modal analysis is carried on, the main modal parameters obtained, and so the basis can be provided for the further study of dynamic characteristics and influencing factors of twin ball screw driving linear guide feed unit.

2 2 TWIN BALL SCREW DRIVING LINEAR GUIDE FEED UNIT TABLE The structure of twin ball screw driving linear guide feed unit test table is shown in Figure. 1. It includes the base, twin ball screws, twin linear guides, twin support ball bearings and bearing supports, and table which does reciprocating linear motion along the ball screw pair. 3.2 Choosing the unit type, defining material properties and meshing (1) Selecting unit type In the ANSYS structural dynamics analysis, since Solid92 unit is 10 nodes hexahedron, its simulation of curve boundary is ideal, meshing is convenient by means of MeshTool and Refine mesh, it is the first selection for three-dimensional model of the irregular boundary. So 10 nodes SOLID92 unit is choosen as the unit type of the feed unit. (2) Defining the material properties The material properties of every component of the feed unit is shown in Table 1. Figure 1. Schematic diagram of feed unit test table. 3 FINITE ELEMENT ANALYSIS OF TWIN BALL SCREW DRIVING LINEAR GUIDE FEED UNIT TABLE Only linear behavior can be analyzed in the modal analysis of ANASY,while nonlinear units specified in the analysis usually are ignored and dealed with as linear units.moreover, the nature of the material in modal analysis must be linear and isotropic, therefore such linear features as the elastic modulus and density of the material must specified, and its nonlinear material properties ignored. The whole analysis process is as the following. 3.1 Three-dimensional solid model In this paper,the structure of the feed unit researched is complicated, so the direct modeling is difficult in ANSYS. So the model is established in SolidWorks software, and then imported into the ANSYS to be analyzed so that the difficulty of modeling the complex model in ANSYS can be greatly reduced. Some small structure features of feed unit, such as chamfer, thread, etc., will increase the number of units after the meshing and impact the efficiency of analysis and calculation,but the effects on the dynamic characteristics of the whole structure are little. As a result, the model is simplified and imported into ANSYS as shown in Figure. 2. Figure 2. Simplified model. 12 Table 1. Material properties of every component of feed unit. Properties Values Elastic modulus pa Poisson's ratio 0.3 Density kg/cm 3 Material damping 0.1 (3) Meshing There are many kinds of meshing methods in ANSYS, such as free meshing, mapped meshing, sweep meshing, and hybrid meshing, etc. In the paper,mapped meshing is adopted for ball screws and free meshing is used to the rest part of twin ball screw drive linear guide feed unit, and the result of meshing is shown in Figure Loading and solution Both ends fixed installation is choosen for the ball screw pair, so all constraints of three s are loaded to two fixed ends and the base. After boundary conditions and loading is completed and then modal analysis type is set in the solver, the first vibration modes when the nut is located at the middle position of the feed unit are shown in Figure 4. 6 order modals are extracted using the Block Lanczos method. 3.4 Model anlysis results In this paper, modal analysis is carried on respectively when the nut is located at the left end, middle and right end position of feed unit, and the results of the natural frequency analysis in different positions are shown in Table 2. Table 2. Natural frequency and vibration shape description of feed unit. Position Modal Natural frequency and vibration shape description Middle the first-order bending of ball screws in Y the first-order bending

3 Right end Left end the first-order rotation of table around X Axle the first-order bending of table in Z the second-order bending the second-order torsion of table around Y Axle the first-order bending the first-order bending of ball screws in Y the first-order rotation of table around X Axle the first-order bending of table in Z the second-order bending the second-order torsion of table around Y Axle the first-order bending of ball screws in the same Z the first-order bending of ball screw in different Z the first-order bending of ball screws in different Y the first-order bending of ball screws in the same Y the second-order bending of ball screws in the same Z the second-order bending of ball screws in different Z Figure 3. Meshing result of feed unit. (c) 3rd order 13

4 (d) 4th order (c) 3rd order Figure 4. Modal analysis results when the nut is located at the middle position of the feed unit. Vibration modes when the nut is located at the right end of the feed unit are shown in Figure 5. 14

5 position of single ball screw driving feed unit are shown in Table 3. and Figure 7. (d) 4th order Figure 5. Modal analysis results when the nut is located at the left end of the feed unit. (c) 3rd order Vibration modes when the nut is located at the left end of the feed unit are shown in Figure 6. The natural frequencies and vibration shape description when the nut is located at the middle 15

6 Table 3. Natural frequency and vibration shape description of single ball screw driving feed unit. Modal Natural frequency Vibration shape description the first-order bending of ball screw in Z the first-order bending of ball screw in Y the first-order bending of table in Z the first-order rotation of table around Z the second-order bending of ball screw in Z the second-order bending of ball screw in Y (d) 4th order Figure 6. Modal analysis results when the nut is located at the right end of the feed unit. 16

7 (c) 3rd order Figure 7. Modal analysis results when the nut is located at the middle position of single ball screw driving feed system. 4 CONCLUSIONS The above analysis results show that under the same vibration shape, the natural frequencies of twin ball screw driving feed unit are larger than those of single ball screw driving feed unit, and the position of nut of twin ball screw drive linear guide feed unit has obvious influence on the dynamic characteristics of the feed unit, and each order natural frequency at two fixed ends is significantly higher than that in the middle position. (d) 4th order 5 ACKNOWLEDGMENT This work was financially supported by the National Natural Science Foundation of China ( ) and the Doctoral Funds of Shandong Jianzhu University (XNBS1246). REFERENCES [1] He Wangyong, Tang Xiaoqi & Li Yongbo.2010.Dynamics modeling and analysis of a motion axis driven by a synchronous dual ball screw based on FEA. Manufacturing Technology & Machine Tool (12): [2] Yang yong.2010.influnence of drive at center of gravity and guide joint surface parameters on dynamic characteristics of machine tool. Nanjing:China. [3] Zhouyong.2008.Dynamic characteristics analysis and motion control research of high speed feed drive system.wuhan: China. [4] Huangxiaoyan & Lizhuang Application of the principle of drive at center of gravity to the structure design of key components of high-speed horizontal boring and milling machining center. Dalian HuaGen machinery co., LTD:China. [5] Ding Xihe.2014.Dynamic characteristics analysis of dual ball screw drive linear feed system. Modular Machine Tool & Automatic Manufacturing Technique (3): [6] Wang Renche, Zhao Tong, Ye Peiqing & Liu Yan Three-Dimensional modeling for predicting the vibration modes of twin ball screw driving table. Chinese Journal of Mechanical Engineering 27(1):

Modal Analysis of Propulsion Shafting of a 48,000 tons Bulk Carrier

Modal Analysis of Propulsion Shafting of a 48,000 tons Bulk Carrier Modal Analysis of Propulsion Shafting of a 48,000 tons Bulk Carrier Zixin Wang a Dalian Scientific Test and Control Technology Institute. 16 Binhai Street. Dalian, 116013, China. Abstract a wangzixin_1@163.com

More information

Dynamic Characteristics of the End-effector of a Drilling Robot for Aviation

Dynamic Characteristics of the End-effector of a Drilling Robot for Aviation International Journal of Materials Science and Applications 2018; 7(5): 192-198 http://www.sciencepublishinggroup.com/j/ijmsa doi: 10.11648/j.ijmsa.20180705.14 ISSN: 2327-2635 (Print); ISSN: 2327-2643

More information

Application of pushover analysis in estimating seismic demands for large-span spatial structure

Application of pushover analysis in estimating seismic demands for large-span spatial structure 28 September 2 October 2009, Universidad Politecnica de Valencia, Spain Alberto DOMINGO and Carlos LAZARO (eds.) Application of pushover analysis in estimating seismic demands for large-span spatial structure

More information

Vibration Analysis and Test of Backup Roll in Temper Mill

Vibration Analysis and Test of Backup Roll in Temper Mill Sensors & Transducers 2013 by IFSA http://www.sensorsportal.com Vibration Analysis and Test of Backup Roll in Temper Mill Yuanmin Xie College of Machinery and Automation, Wuhan University of Science and

More information

APPLICATION OF PUSHOVER ANALYSIS ON EARTHQUAKE RESPONSE PREDICATION OF COMPLEX LARGE-SPAN STEEL STRUCTURES

APPLICATION OF PUSHOVER ANALYSIS ON EARTHQUAKE RESPONSE PREDICATION OF COMPLEX LARGE-SPAN STEEL STRUCTURES APPLICATION OF PUSHOVER ANALYSIS ON EARTHQUAKE RESPONSE PREDICATION OF COMPLEX LARGE-SPAN STEEL STRUCTURES J.R. Qian 1 W.J. Zhang 2 and X.D. Ji 3 1 Professor, 3 Postgraduate Student, Key Laboratory for

More information

The Application of ANSYS Contact Analysis in Cable Crane Load Conversion Device

The Application of ANSYS Contact Analysis in Cable Crane Load Conversion Device 2017 2nd International Conference on Mechanical Control and Automation (ICMCA 2017) ISBN: 978-1-60595-460-8 The Application of ANSYS Contact Analysis in Cable Crane Load Conversion Device Yong-shi HU 1,*,

More information

The Study of Half-tooth Master Gear Structure Optimization Yazhou Xie a, Zhiliang Qian b

The Study of Half-tooth Master Gear Structure Optimization Yazhou Xie a, Zhiliang Qian b X 3rd International Conference on Mechatronics, Robotics and Automation (ICMRA 2015) The Study of Half-tooth Master Gear Structure Optimization Yazhou Xie a, Zhiliang Qian b School of Mechanical and Electric

More information

Structural Design and Analysis of the New Mobile Refuge Chamber

Structural Design and Analysis of the New Mobile Refuge Chamber Key Engineering Materials Online: 2013-09-10 ISSN: 1662-9795, Vol. 584, pp 175-178 doi:10.4028/www.scientific.net/kem.584.175 2014 Trans Tech Publications, Switzerland Structural Design and Analysis of

More information

Keywords: contra-rotating fan, air pressure, deformation of blades.

Keywords: contra-rotating fan, air pressure, deformation of blades. 2nd International Conference on Machinery, Materials Engineering, Chemical Engineering and Biotechnology (MMECEB 2015) Study on Deformation of the Two Rotors of Contra-Rotating Fan under Variable Speeds

More information

Experimental research on instability fault of high-speed aerostatic bearing-rotor system

Experimental research on instability fault of high-speed aerostatic bearing-rotor system Experimental research on instability fault of high-speed aerostatic bearing-rotor system Dongjiang Han 1, Changliang Tang 2, Jinfu Yang 3, Long Hao 4 Institute of Engineering Thermophysics, Chinese Academy

More information

A Numerical Simulation of Fluid-Structure Interaction for Refrigerator Compressors Suction and Exhaust System Performance Analysis

A Numerical Simulation of Fluid-Structure Interaction for Refrigerator Compressors Suction and Exhaust System Performance Analysis 1131, Page 1 A Numerical Simulation of Fluid-Structure Interaction for Refrigerator Compressors Suction and Exhaust System Performance Analysis Shoufei Wu*, Zonghuai Wang Jiaxipera Compressor Co., Ltd.,

More information

Acoustical Modeling of Reciprocating Compressors With Stepless Valve Unloaders

Acoustical Modeling of Reciprocating Compressors With Stepless Valve Unloaders Acoustical Modeling of Reciprocating Compressors With Stepless Valve Unloaders Kelly Eberle, P.Eng. Principal Engineer keberle@betamachinery.com Brian C. Howes, M.Sc., P.Eng. Chief Engineer bhowes@betamachinery.com

More information

Structural Analysis of Mast of Special Rotary Drilling Rig for Transmission Line

Structural Analysis of Mast of Special Rotary Drilling Rig for Transmission Line 5th International Conference on Advanced Engineering Materials and Technology (AEMT 2015) Structural Analysis of Mast of Special Rotary Drilling Rig for Transmission Line Jian Qin1, a *, Yimin Ma1, b,

More information

Numerical Simulation of the Basketball Flight Trajectory based on FLUENT Fluid Solid Coupling Mechanics Yanhong Pan

Numerical Simulation of the Basketball Flight Trajectory based on FLUENT Fluid Solid Coupling Mechanics Yanhong Pan Applied Mechanics and Materials Submitted: 2014-08-05 ISSN: 1662-7482, Vols. 651-653, pp 2347-2351 Accepted: 2014-08-06 doi:10.4028/www.scientific.net/amm.651-653.2347 Online: 2014-09-30 2014 Trans Tech

More information

Research on Small Wind Power System Based on H-type Vertical Wind Turbine Rong-Qiang GUAN a, Jing YU b

Research on Small Wind Power System Based on H-type Vertical Wind Turbine Rong-Qiang GUAN a, Jing YU b 06 International Conference on Mechanics Design, Manufacturing and Automation (MDM 06) ISBN: 978--60595-354-0 Research on Small Wind Power System Based on H-type Vertical Wind Turbine Rong-Qiang GUAN a,

More information

DESIGN OPTIMIZATION OF WORK ROLL CHOCK AND BACKUP ROLL CHOCK IN COLD ROLLING MILL

DESIGN OPTIMIZATION OF WORK ROLL CHOCK AND BACKUP ROLL CHOCK IN COLD ROLLING MILL DESIGN OPTIMIZATION OF WORK ROLL CHOCK AND BACKUP ROLL CHOCK IN COLD ROLLING MILL Tukesh Sahu 1, Prof. G.R.Kesheory 2 1M.Tech Scholar, Department of Mechanical Engineering, VITS Indore, MP, India 2Assistant

More information

Simulation Research of a type of Pressure Vessel under Complex Loading Part 1 Component Load of the Numerical Analysis

Simulation Research of a type of Pressure Vessel under Complex Loading Part 1 Component Load of the Numerical Analysis Simulation Research of a type of Pressure Vessel under Complex Loading Part 1 Component Load of the Numerical Analysis Yufu Zhang 1,2 1. College of Materials Science and Engineering, ; 2. Gansu Lanpec

More information

67. Sectional normalization and recognization on the PV-Diagram of reciprocating compressor

67. Sectional normalization and recognization on the PV-Diagram of reciprocating compressor 67. Sectional normalization and recognization on the PV-Diagram of reciprocating compressor Jin-dong Wang 1, Yi-qi Gao 2, Hai-yang Zhao 3, Rui Cong 4 School of Mechanical Science and Engineering, Northeast

More information

Aerodynamic Measures for the Vortex-induced Vibration of π-shape Composite Girder in Cable-stayed Bridge

Aerodynamic Measures for the Vortex-induced Vibration of π-shape Composite Girder in Cable-stayed Bridge Aerodynamic Measures for the Vortex-induced Vibration of π-shape Composite Girder in Cable-stayed Bridge *Feng Wang 1), Jialing Song 2), Tuo Wu 3), and Muxiong Wei 4) 1), 2, 3), 4) Highway School, Chang

More information

CHAPTER IV FINITE ELEMENT ANALYSIS OF THE KNEE JOINT WITHOUT A MEDICAL IMPLANT

CHAPTER IV FINITE ELEMENT ANALYSIS OF THE KNEE JOINT WITHOUT A MEDICAL IMPLANT 39 CHAPTER IV FINITE ELEMENT ANALYSIS OF THE KNEE JOINT WITHOUT A MEDICAL IMPLANT 4.1 Modeling in Biomechanics The human body, apart of all its other functions is a mechanical mechanism and a structure,

More information

The Study on the Influence of Gust Wind on Vehicle Stability Chen Wang a, Haibo Huang b*, Shaofang Xu c

The Study on the Influence of Gust Wind on Vehicle Stability Chen Wang a, Haibo Huang b*, Shaofang Xu c Applied Mechanics and Materials Submitted: 214-6-4 ISSN: 1662-7482, Vol. 598, pp 198-21 Accepted: 214-6-4 doi:1.428/www.scientific.net/amm.598.198 Online: 214-7-16 214 Trans Tech Publications, Switzerland

More information

GEA FOR ADVANCED STRUCTURAL DYNAMIC ANALYSIS

GEA FOR ADVANCED STRUCTURAL DYNAMIC ANALYSIS SMART SOLUTIONS FOR VIBRATION MONITORING GEA FOR ADVANCED STRUCTURAL DYNAMIC ANALYSIS ANALYSIS OF CIVIL STRUCTURES - EXPO MERLATA PEDESTRIAN BRIDGE ABSTRACT Civil structures and in particular bridges and

More information

The Mechanism Study of Vortex Tools Drainage Gas Recovery of Gas Well

The Mechanism Study of Vortex Tools Drainage Gas Recovery of Gas Well Advances in Petroleum Exploration and Development Vol. 7, No. 1, 214, pp. 62-66 DOI:1.3968/j.aped.1925543821471.1931 ISSN 1925-542X [Print] ISSN 1925-5438 [Online] www.cscanada.net www.cscanada.org The

More information

Elastic-Plastic Finite Element Analysis for Zhongwei--guiyang Natural Gas Pipeline Endangered by Collapse

Elastic-Plastic Finite Element Analysis for Zhongwei--guiyang Natural Gas Pipeline Endangered by Collapse Abstract Elastic-Plastic Finite Element Analysis for Zhongwei--guiyang Natural Gas Pipeline Endangered by Collapse Gengxin Wu,Peng Zhang,Zhixiang Li,Zunhai Ke,Guizhi Li,Anmin Jiang 2 School of Civil Engineering

More information

Stress evaluation of a bicycle crank arm connection using BEM

Stress evaluation of a bicycle crank arm connection using BEM Stress evaluation of a bicycle crank arm connection using BEM C. J. Hoff, R. E. Dippery & 3. Knapp Department of Mechanical Engineering Kettering University, USA Abstract An interesting problem encountered

More information

Stress Analysis of The West -East gas pipeline with Defects Under Thermal Load

Stress Analysis of The West -East gas pipeline with Defects Under Thermal Load Stress Analysis of The West -East gas pipeline with Defects Under Thermal Load Abstract Xu Lei School of Petroleum Engineering, Yangtze University, Wuhan 430000, China 13071247220@163.com Natural gas is

More information

Analysis of Steady-state Characteristics of Aerodynamic Bearing Based on FLUENT JIA Chenhui 1,a, Du Caifeng 2,b and QIU Ming 3,c

Analysis of Steady-state Characteristics of Aerodynamic Bearing Based on FLUENT JIA Chenhui 1,a, Du Caifeng 2,b and QIU Ming 3,c International Conference on Intelligent Systems Research and Mechatronics Engineering (ISRME 2015) Analysis of Steady-state Characteristics of Aerodynamic Bearing Based on FLUENT JIA Chenhui 1,a, Du Caifeng

More information

Simulation and mathematical modeling for racket position and attitude of table tennis

Simulation and mathematical modeling for racket position and attitude of table tennis Acta Technica 62 No. 3A/2017, 135 142 c 2017 Institute of Thermomechanics CAS, v.v.i. Simulation and mathematical modeling for racket position and attitude of table tennis Jiansi Song 1 Abstract. Racket

More information

Vibration measurement method of the ship propulsion shafting

Vibration measurement method of the ship propulsion shafting Vibration measurement method of the ship propulsion shafting Chunlei Zhang Dalian Scientific Test and Control Technology Institute. 16 Binhai Street. Dalian, 116013, China. Abstract zhangchunlei_760@163.com

More information

Computer Aided Drafting, Design and Manufacturing Volume 26, Number 2, June 2016, Page 53. The design of exoskeleton lower limbs rehabilitation robot

Computer Aided Drafting, Design and Manufacturing Volume 26, Number 2, June 2016, Page 53. The design of exoskeleton lower limbs rehabilitation robot Computer Aided Drafting, Design and Manufacturing Volume 26, Number 2, June 2016, Page 53 CADDM The design of exoskeleton lower limbs rehabilitation robot Zhao Xiayun 1, Wang Zhengxing 2, Liu Zhengyu 1,3,

More information

Journal of Chemical and Pharmaceutical Research, 2016, 8(6): Research Article. Walking Robot Stability Based on Inverted Pendulum Model

Journal of Chemical and Pharmaceutical Research, 2016, 8(6): Research Article. Walking Robot Stability Based on Inverted Pendulum Model Available online www.jocpr.com Journal of Chemical and Pharmaceutical Research, 2016, 8(6):463-467 Research Article ISSN : 0975-7384 CODEN(USA) : JCPRC5 Walking Robot Stability Based on Inverted Pendulum

More information

CFD Simulation and Experimental Validation of a Diaphragm Pressure Wave Generator

CFD Simulation and Experimental Validation of a Diaphragm Pressure Wave Generator CFD Simulation and Experimental Validation of a Diaphragm Pressure Wave Generator T. Huang 1, A. Caughley 2, R. Young 2 and V. Chamritski 1 1 HTS-110 Ltd Lower Hutt, New Zealand 2 Industrial Research Ltd

More information

Numerical Investigation of Air Bubbles Evolution and Coalescence from Submerged Orifices Based on OpenFOAM

Numerical Investigation of Air Bubbles Evolution and Coalescence from Submerged Orifices Based on OpenFOAM Numerical Investigation of Air Bubbles Evolution and Coalescence from Submerged Orifices Based on OpenFOAM Pan Feng, He Ying, Li-zhong Mu 2018-7-6 Dalian University of Technology, China Outline Background

More information

Performance Analysis of Centrifugal Compressor under Multiple Working Conditions Based on Time-weighted Average

Performance Analysis of Centrifugal Compressor under Multiple Working Conditions Based on Time-weighted Average Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2014 Performance Analysis of Centrifugal Compressor under Multiple Working Conditions Based

More information

Gorge Wind Characteristics in Mountainous Area in South-West China Based on Field Measurement

Gorge Wind Characteristics in Mountainous Area in South-West China Based on Field Measurement Gorge Wind Characteristics in Mountainous Area in South-West China Based on Field Measurement *Yingzi Zhong 1) and Mingshui Li 2) 1), 2) Research Centre for Wind Engineering, Southwest Jiaotong University,

More information

FEA case Study: Rubber expansion joint for piping systems

FEA case Study: Rubber expansion joint for piping systems FEA case Study: Rubber expansion joint for piping systems Introduction The FEA Toolbox of Taniq makes it possible to simulate the behavior of a pipe expansion joint accurately under several load cases.

More information

NUMERICAL SIMULATION OF STATIC INTERFERENCE EFFECTS FOR SINGLE BUILDINGS GROUP

NUMERICAL SIMULATION OF STATIC INTERFERENCE EFFECTS FOR SINGLE BUILDINGS GROUP NUMERICAL SIMULATION OF STATIC INTERFERENCE EFFECTS FOR SINGLE BUILDINGS GROUP Xing-qian Peng, Chun-hui Zhang 2 and Chang-gui Qiao 2 Professor, College of Civil Engineering, Huaqiao University, Quanzhou,

More information

The Adequacy of Pushover Analysis to Evaluate Vulnerability of Masonry Infilled Steel Frames Subjected to Bi-Directional Earthquake Loading

The Adequacy of Pushover Analysis to Evaluate Vulnerability of Masonry Infilled Steel Frames Subjected to Bi-Directional Earthquake Loading The Adequacy of Pushover Analysis to Evaluate Vulnerability of Masonry Infilled Steel Frames Subjected to Bi-Directional Earthquake Loading B.Beheshti Aval & M. Mohammadzadeh K.N.Toosi University of Technology,

More information

Numerical simulation of three-dimensional flow field in three-line rollers and four-line rollers compact spinning systems using finite element method

Numerical simulation of three-dimensional flow field in three-line rollers and four-line rollers compact spinning systems using finite element method Indian Journal of Fibre & Textile Research Vol. 42, March 2017, pp. 77-82 Numerical simulation of three-dimensional flow field in three-line rollers and four-line rollers compact spinning systems using

More information

An Impeller Blade Analysis of Centrifugal Gas Compressor Using CFD

An Impeller Blade Analysis of Centrifugal Gas Compressor Using CFD An Impeller Blade Analysis of Centrifugal Gas Compressor Using CFD Vivek V. Kulkarni Department of Mechanical Engineering KLS Gogte Institute of Technology, Belagavi, Karnataka Dr. Anil T.R. Department

More information

Study on the shape parameters of bulbous bow of. tuna longline fishing vessel

Study on the shape parameters of bulbous bow of. tuna longline fishing vessel International Conference on Energy and Environmental Protection (ICEEP 2016) Study on the shape parameters of bulbous bow of tuna longline fishing vessel Chao LI a, Yongsheng WANG b, Jihua Chen c Fishery

More information

Kochi University of Technology Aca Study on Dynamic Analysis and Wea Title stem for Golf Swing Author(s) LI, Zhiwei Citation 高知工科大学, 博士論文. Date of 2015-03 issue URL http://hdl.handle.net/10173/1281 Rights

More information

Hunting for the Sweet Spot by a Seesaw Model

Hunting for the Sweet Spot by a Seesaw Model Hunting for the Sweet Spot by a Seesaw Model Haiyan Li 1, Jianling Li, Shijun Li 1, and Zhaotian Liu 1 1 School of Information Science and Engineering, Yunnan University, Kunming, Yunnan, 650091, China

More information

Analysis of the Impact of Rotor Rigidity on the Aerodynamic Performance of Vertical Axis Wind Turbines

Analysis of the Impact of Rotor Rigidity on the Aerodynamic Performance of Vertical Axis Wind Turbines Analysis of the Impact of Rotor Rigidity on the Aerodynamic Performance of Vertical Axis Wind Turbines Ziqin ZHAO, Shangke YUAN School of Civil Engineering, Lanzhou Institute of Technology, Lanzhou, Gansu

More information

Numerical Simulation of Fluid-Structure Interaction in the Design Process for a New Axial Hydraulic Pump

Numerical Simulation of Fluid-Structure Interaction in the Design Process for a New Axial Hydraulic Pump Numerical Simulation of Fluid-Structure Interaction in the Design Process for a New Axial Hydraulic Pump Bettina Landvogt¹, Leszek Osiecki², Tomasz Zawistowski³, Bartek Zylinski 4 1 Fraunhofer SCAI, Germany,

More information

STUDY OF UNDERWATER THRUSTER (UT) FRONT COVER OF MSI300 AUTONOMOUS UNDERWATER VEHICLE (AUV) USING FINITE ELEMENT ANALYSIS (FEA)

STUDY OF UNDERWATER THRUSTER (UT) FRONT COVER OF MSI300 AUTONOMOUS UNDERWATER VEHICLE (AUV) USING FINITE ELEMENT ANALYSIS (FEA) STUDY OF UNDERWATER THRUSTER (UT) FRONT COVER OF MSI300 AUTONOMOUS UNDERWATER VEHICLE (AUV) USING FINITE ELEMENT ANALYSIS (FEA) M. Sabri 1, 2, T. Ahmad 1, M. F. M. A. Majid 1 and A. B. Muhamad Husaini

More information

A NEW GOLF-SWING ROBOT MODEL UTILIZING SHAFT ELASTICITY

A NEW GOLF-SWING ROBOT MODEL UTILIZING SHAFT ELASTICITY Journal of Sound and Vibration (1998) 17(1), 17 31 Article No. sv981733 A NEW GOLF-SWING ROBOT MODEL UTILIZING SHAFT ELASTICITY S. SUZUKI Department of Mechanical System Engineering, Kitami Institute of

More information

Baseball best hitting point model research based on momentum medium theorem

Baseball best hitting point model research based on momentum medium theorem ISSN : 974-7435 Volume Issue 4 Baseball best hitting point model research based on momentum medium theorem Yong Li Institute of Physical Education, hina est Normal University, Nanchong, Sichuan, (HINA)

More information

Modeling of thin strip profile during cold rolling on roll crossing and shifting mill

Modeling of thin strip profile during cold rolling on roll crossing and shifting mill University of Wollongong Research Online Faculty of Engineering and Information Sciences - Papers: Part A Faculty of Engineering and Information Sciences 2013 Modeling of thin strip profile during cold

More information

Design and Optimization of Weld Neck Flange for Pressure Vessel

Design and Optimization of Weld Neck Flange for Pressure Vessel V th International Symposium on Fusion of Science & Technology, New Delhi, India, January 18-22, 2016 ID: 2016-ISFT-430 Design and Optimization of Weld Neck Flange for Pressure Vessel Vinod Kumar 1, Vivek

More information

Study on Mixing Property of Circulation/Shear Coupling Mechanism-Double Impeller Configuration

Study on Mixing Property of Circulation/Shear Coupling Mechanism-Double Impeller Configuration Study on Mixing Property of Circulation/Shear Coupling Mechanism-Double Impeller Configuration 1 LI Zhen, 2 YANG Chao 1,2 School of Chemistry and Chemical Engineering, Xi an University of Science and Technology,

More information

ICE PRESSURE MEASUREMENT UNDER FLOWING CONDITIONS ON HARBIN REACH OF SONGHUA RIVER

ICE PRESSURE MEASUREMENT UNDER FLOWING CONDITIONS ON HARBIN REACH OF SONGHUA RIVER Ice in the Environment: Proceedings of the 16th IAHR International Symposium on Ice Dunedin, New Zealand, 2nd 6th December 2002 International Association of Hydraulic Engineering and Research ICE PRESSURE

More information

Modeling of Hydraulic Hose Paths

Modeling of Hydraulic Hose Paths Mechanical Engineering Conference Presentations, Papers, and Proceedings Mechanical Engineering 9-2002 Modeling of Hydraulic Hose Paths Kurt A. Chipperfield Iowa State University Judy M. Vance Iowa State

More information

The Kinematics Analysis of Wu Yibing's Tennis Forehand Technique Xin WEN, Ji-he ZHOU and Chuan-jia DU

The Kinematics Analysis of Wu Yibing's Tennis Forehand Technique Xin WEN, Ji-he ZHOU and Chuan-jia DU 218 International Conference on Mechanical, Electronic and Information Technology (ICMEIT 218) ISBN: 978-1-6595-548-3 The Kinematics Analysis of Wu Yibing's Tennis Forehand Technique Xin WEN, Ji-he ZHOU

More information

Numerical Simulation And Aerodynamic Performance Comparison Between Seagull Aerofoil and NACA 4412 Aerofoil under Low-Reynolds 1

Numerical Simulation And Aerodynamic Performance Comparison Between Seagull Aerofoil and NACA 4412 Aerofoil under Low-Reynolds 1 Advances in Natural Science Vol. 3, No. 2, 2010, pp. 244-20 www.cscanada.net ISSN 171-7862 [PRINT] ISSN 171-7870 [ONLINE] www.cscanada.org *The 3rd International Conference of Bionic Engineering* Numerical

More information

Numerical Simulation for the Internal Flow Analysis of the Linear Compressor with Improved Muffler

Numerical Simulation for the Internal Flow Analysis of the Linear Compressor with Improved Muffler Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2016 Numerical Simulation for the Internal Flow Analysis of the Linear Compressor with Improved

More information

Tightening Evaluation of New 400A Size Metal Gasket

Tightening Evaluation of New 400A Size Metal Gasket Proceedings of the 8th International Conference on Innovation & Management 307 Tightening Evaluation of New 400A Size Metal Gasket Moch. Agus Choiron 1, Shigeyuki Haruyama 2, Ken Kaminishi 3 1 Doctoral

More information

The Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration. M. Burak Şamşul

The Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration. M. Burak Şamşul The Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration M. Burak Şamşul ITU AYOC 2014 - Milper Pervane Teknolojileri Company Profile MILPER is established in 2011 as a Research and Development

More information

Lateral Load Analysis Considering Soil-Structure Interaction. ANDREW DAUMUELLER, PE, Ph.D.

Lateral Load Analysis Considering Soil-Structure Interaction. ANDREW DAUMUELLER, PE, Ph.D. Lateral Load Analysis Considering Soil-Structure Interaction ANDREW DAUMUELLER, PE, Ph.D. Overview Introduction Methods commonly used to account for soil-structure interaction for static loads Depth to

More information

Friction properties of the face of a hand-held tennis racket

Friction properties of the face of a hand-held tennis racket Available online at www.sciencedirect.com Procedia Engineering 34 (2012 ) 544 549 9 th Conference of the International Sports Engineering Association (ISEA) Friction properties of the face of a hand-held

More information

International Journal of Technical Research and Applications e-issn: , Volume 4, Issue 3 (May-June, 2016), PP.

International Journal of Technical Research and Applications e-issn: ,  Volume 4, Issue 3 (May-June, 2016), PP. DESIGN AND ANALYSIS OF FEED CHECK VALVE AS CONTROL VALVE USING CFD SOFTWARE R.Nikhil M.Tech Student Industrial & Production Engineering National Institute of Engineering Mysuru, Karnataka, India -570008

More information

Design of control system using electric cylinder for automated measurement of bearing shell crush height

Design of control system using electric cylinder for automated measurement of bearing shell crush height Int J Adv Manuf Technol (2018) 95:983 989 https://doi.org/10.1007/s00170-017-1211-3 ORIGINAL ARTICLE Design of control system using electric cylinder for automated measurement of bearing shell crush height

More information

Analysis of Jump-Out Loads about Connectors of Buttress and Round Threads of Casing

Analysis of Jump-Out Loads about Connectors of Buttress and Round Threads of Casing nalysis of Jump-Out Loads about onnectors of uttress and Round Threads of asing Lian Zhanghua, Liu Yonggang, Tang o Southwest Petroleum Institute, P.R. Of hina Han Jianzeng, Zhang Yi Shanghai aoshan Iron

More information

Yuele Jia Computer Science School, Southwest Petroleum University, Chengdu , Sichuan, China

Yuele Jia Computer Science School, Southwest Petroleum University, Chengdu , Sichuan, China doi:10.1311/001.39.10.41 Snubbing Operation Process Simulation Based on String Stress Actuation Yuele Jia Computer Science School, Southwest Petroleum University, Chengdu 610500, Sichuan, China Zhi Chen

More information

Numerical simulation and analysis of aerodynamic drag on a subsonic train in evacuated tube transportation

Numerical simulation and analysis of aerodynamic drag on a subsonic train in evacuated tube transportation Journal of Modern Transportation Volume 20, Number 1, March 2012, Page 44-48 Journal homepage: jmt.swjtu.edu.cn DOI: 10.1007/BF03325776 1 Numerical simulation and analysis of aerodynamic drag on a subsonic

More information

The Application of Pedestrian Microscopic Simulation Technology in Researching the Influenced Realm around Urban Rail Transit Station

The Application of Pedestrian Microscopic Simulation Technology in Researching the Influenced Realm around Urban Rail Transit Station Journal of Traffic and Transportation Engineering 4 (2016) 242-246 doi: 10.17265/2328-2142/2016.05.002 D DAVID PUBLISHING The Application of Pedestrian Microscopic Simulation Technology in Researching

More information

Fatigue Analysis of English-Willow Cricket Bat

Fatigue Analysis of English-Willow Cricket Bat Fatigue Analysis of English-Willow Cricket Bat Mr. Rajshekhar Chimmat 1, Mr. Shreenidhi Kulkarni 2 1M.Tech. Scholar, Dept. of Mechanical Engineering, KLS Gogte Institute of Technology, Belagavi, Karnataka,

More information

EMA and Other Dynamic Testing of a 2-Span Prestressed Concrete Floor. Tuan Nguyen, Nicholas Haritos, Emad Gad and John Wilson

EMA and Other Dynamic Testing of a 2-Span Prestressed Concrete Floor. Tuan Nguyen, Nicholas Haritos, Emad Gad and John Wilson EMA and Other Dynamic Testing of a 2-Span Prestressed Concrete Floor Tuan Nguyen, Nicholas Haritos, Emad Gad and John Wilson INTRODUCTION This paper discusses experimental modal analysis (EMA) using swept

More information

OPTIMIZATION OF SINGLE STAGE AXIAL FLOW COMPRESSOR FOR DIFFERENT ROTATIONAL SPEED USING CFD

OPTIMIZATION OF SINGLE STAGE AXIAL FLOW COMPRESSOR FOR DIFFERENT ROTATIONAL SPEED USING CFD http:// OPTIMIZATION OF SINGLE STAGE AXIAL FLOW COMPRESSOR FOR DIFFERENT ROTATIONAL SPEED USING CFD Anand Kumar S malipatil 1, Anantharaja M.H 2 1,2 Department of Thermal Power Engineering, VTU-RO Gulbarga,

More information

Vibrations of table tennis racket composite wood blades: modeling and experiments

Vibrations of table tennis racket composite wood blades: modeling and experiments Available online at www.sciencedirect.com Procedia Engineering 34 (2012 ) 694 699 9 th Conference of the International Sports Engineering Association (ISEA) Vibrations of table tennis racket composite

More information

Analysis of wind resistance of high-rise building structures based on computational fluid dynamics simulation technology

Analysis of wind resistance of high-rise building structures based on computational fluid dynamics simulation technology International Journal of Heat and Technology Vol. 36, No. 1, March, 18, pp. 376-38 Journal homepage: http://iieta.org/journals/ijht Analysis of wind resistance of high-rise building structures based on

More information

Finite Element Analysis and Design of Lower Extremity Exoskeleton

Finite Element Analysis and Design of Lower Extremity Exoskeleton Finite Element Analysis and Design of Lower Extremity Exoskeleton Huazeng Hu, Guanghao Zhang, Feng Li College of Mechanical and Electronic Engineering, Shandong University of Science and Technology, Qingdao

More information

Adaptive Pushover Analysis of Irregular RC Moment Resisting Frames

Adaptive Pushover Analysis of Irregular RC Moment Resisting Frames Kalpa Publications in Civil Engineering Volume 1, 2017, Pages 132 136 ICRISET2017. International Conference on Research and Innovations in Science, Engineering &Technology. Selected papers in Civil Engineering

More information

CFD Analysis ofwind Turbine Airfoil at Various Angles of Attack

CFD Analysis ofwind Turbine Airfoil at Various Angles of Attack IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 13, Issue 4 Ver. II (Jul. - Aug. 2016), PP 18-24 www.iosrjournals.org CFD Analysis ofwind Turbine

More information

ANALYSIS OF THE POSITIVE FORCES EXHIBITING ON THE MOORING LINE OF COMPOSITE-TYPE SEA CAGE

ANALYSIS OF THE POSITIVE FORCES EXHIBITING ON THE MOORING LINE OF COMPOSITE-TYPE SEA CAGE 194 He, W., Li, C.: Analysis of the positive forces exhibiting on ANALYSIS OF THE POSITIVE FORCES EXHIBITING ON THE MOORING LINE OF COMPOSITE-TYPE SEA CAGE Wei He 1* Chunliu Li 2 1 Ocean College, Agricultural

More information

SPECTRAL CHARACTERISTICS OF FLUCTUATING WIND LOADS ON A SEPARATE TWIN-BOX DECK WITH CENTRAL SLOT

SPECTRAL CHARACTERISTICS OF FLUCTUATING WIND LOADS ON A SEPARATE TWIN-BOX DECK WITH CENTRAL SLOT The Seventh Asia-Pacific Conference on Wind Engineering, November 8-, 009, Taipei, Taiwan SPECTRAL CHARACTERISTICS OF FLUCTUATING WIND LOADS ON A SEPARATE TWIN-BOX DEC WITH CENTRAL SLOT Le-Dong Zhu, Shui-Bing

More information

Single Phase Pressure Drop and Flow Distribution in Brazed Plate Heat Exchangers

Single Phase Pressure Drop and Flow Distribution in Brazed Plate Heat Exchangers Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2016 Single Phase Pressure Drop and Flow Distribution in Brazed Plate Heat Exchangers

More information

Numerical simulation of aerodynamic performance for two dimensional wind turbine airfoils

Numerical simulation of aerodynamic performance for two dimensional wind turbine airfoils Available online at www.sciencedirect.com Procedia Engineering 31 (2012) 80 86 International Conference on Advances in Computational Modeling and Simulation Numerical simulation of aerodynamic performance

More information

Analysis of Pressure Safety Relief Valve using Finite Element Analysis

Analysis of Pressure Safety Relief Valve using Finite Element Analysis Analysis of Pressure Safety Relief Valve using Finite Element Analysis 1 Mr. M. V. Awati, 2 Prof. S. G. Jadhav, 3 Vinay G. Patil 1 P.G.Student, 2 Proffessor, 3 Consultant 1 Mechanical Department, Veermata

More information

A Distributed Control System using CAN bus for an AUV

A Distributed Control System using CAN bus for an AUV International Conference on Information Sciences, Machinery, Materials and Energy (ICISMME 2015) A Distributed Control System using CAN bus for an AUV Wenbao Geng a, Yu Huang b, Peng Lu c No. 710 R&D Institute,

More information

VISIMIX TURBULENT. MECHANICAL CALCULATIONS OF A CONSOLE SHAFT

VISIMIX TURBULENT. MECHANICAL CALCULATIONS OF A CONSOLE SHAFT VISIMIX TURBULENT. MECHANICAL CALCULATIONS OF A CONSOLE SHAFT This example shows how to perform mechanical calculations required to check the shaft reliability, including mechanical strength and vibration

More information

Two-way Fluid Structure Interaction (FSI) Analysis on the Suction Valve Dynamics of a Hermetic Reciprocating Compressor

Two-way Fluid Structure Interaction (FSI) Analysis on the Suction Valve Dynamics of a Hermetic Reciprocating Compressor Volume 118 No. 18 2018, 4241-4252 ISSN: 1311-8080 (printed version); ISSN: 1314-3395 (on-line version) url: http://www.ijpam.eu ijpam.eu Two-way Fluid Structure Interaction (FSI) Analysis on the Suction

More information

The Effect Analysis of Rudder between X-Form and Cross-Form

The Effect Analysis of Rudder between X-Form and Cross-Form 217 3rd International Conference on Computational Systems and Communications (ICCSC 217) The Effect Analysis of Rudder between X-Form and Cross-Form HAN Zhao-Lin1, a, ZHANG Zhong-Zheng2,b, WANG Long- Jin3,

More information

STRESS ANALYSIS OF BICYCLE PADDLE AND OPTIMIZED BY FINITE ELEMENT METHOD. S. Abeygunasekara 1, T. M. M. Amarasekara 2

STRESS ANALYSIS OF BICYCLE PADDLE AND OPTIMIZED BY FINITE ELEMENT METHOD. S. Abeygunasekara 1, T. M. M. Amarasekara 2 - 96 - STRESS ANALYSIS OF BICYCLE PADDLE AND OPTIMIZED BY FINITE ELEMENT METHOD S. Abeygunasekara 1, T. M. M. Amarasekara 2 1 Faculty of Engineering & Technology, Colombo International Nautical Engineering

More information

Experimental Determination of Temperature and Pressure Profile of Oil Film of Elliptical Journal Bearing

Experimental Determination of Temperature and Pressure Profile of Oil Film of Elliptical Journal Bearing International Journal of Advanced Mechanical Engineering. ISSN 2250-3234 Volume 4, Number 5 (2014), pp. 469-474 Research India Publications http://www.ripublication.com Experimental Determination of Temperature

More information

CYCLE ANALYSIS OF LINEAR COMPRESSORS USING THREE- DIMENSIONAL CFD

CYCLE ANALYSIS OF LINEAR COMPRESSORS USING THREE- DIMENSIONAL CFD CYCLE ANALYSIS OF LINEAR COMPRESSORS USING THREE- DIMENSIONAL CFD I. Y. An and Y. L. Lee Department of Mechanical Engineering, Kongju National University, Korea E-Mail: ylee@kongju.ac.kr ABSTRACT In order

More information

Analyses of the fuel cell stack assembly pressure

Analyses of the fuel cell stack assembly pressure Journal of Power Sources 145 (2005) 353 361 Analyses of the fuel cell stack assembly pressure Shuo-Jen Lee, Chen-De Hsu, Ching-Han Huang Department of Mechanical Engineering, Yuan Ze University, 135 FarEast

More information

Available online at ScienceDirect. Procedia Engineering 84 (2014 )

Available online at  ScienceDirect. Procedia Engineering 84 (2014 ) Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 84 (014 ) 97 93 014 ISSST, 014 International Symposium on Safety Science and Technology Research of emergency venting time in

More information

A Study on the Eccentric Loading of K Node of Steel Tube Tower

A Study on the Eccentric Loading of K Node of Steel Tube Tower International Conference on Advances in Energy, Environment and Chemical Engineering (AEECE-2015) A Study on the Eccentric Loading of K Node of Steel Tube Tower LIU Haifeng a Wang Fei b Han Junke b Hu

More information

Effects of Changes of Spokes in the Operation of a Rimmed Flywheel

Effects of Changes of Spokes in the Operation of a Rimmed Flywheel Effects of Changes of Spokes in the Operation of a Rimmed Flywheel M M 1, Ramachandra N K 2, Shruthi RP 3 1 Asst. Professor, Dept. of Mechanical Engineering, T.JOHN Institute of Technology,B lore-83 2

More information

A New version of Autonomous Ocean Energy Recovery System for Oceanic Applications

A New version of Autonomous Ocean Energy Recovery System for Oceanic Applications 21st International Congress on Modelling and Simulation, Gold Coast, Australia, 29 Nov to 4 Dec 2015 www.mssanz.org.au/modsim2015 A New version of Autonomous Ocean Energy Recovery System for Oceanic Applications

More information

Multi-directional Vibration Analysis of Cricket bats

Multi-directional Vibration Analysis of Cricket bats Multi-directional Vibration Analysis of Cricket bats Sabu John & Zhu Bang Li RMIT University, Department of Mechanical & Manufacturing Engineering, Bundoora East Campus, Bundoora, Vic. 3083, Australia.

More information

Analysis of Pressure Rise During Internal Arc Faults in Switchgear

Analysis of Pressure Rise During Internal Arc Faults in Switchgear Analysis of Pressure Rise During Internal Arc Faults in Switchgear ASANUMA, Gaku ONCHI, Toshiyuki TOYAMA, Kentaro ABSTRACT Switchgear include devices that play an important role in operations such as electric

More information

Essential ski characteristics for cross-country skis performance

Essential ski characteristics for cross-country skis performance Proceedings of 7 th ISEA CONFERENCE 2008 Biarritz, June 2-6, 2008 for cross-country skis performance Mikael Bäckström 1, Leon Dahlen 2, Mats Tinnsten 3 (1), (2), (3): Department of Engineering, Physics

More information

Fire safety of staircases in multi-storey buildings The results of measurements in Buildings and Simulations

Fire safety of staircases in multi-storey buildings The results of measurements in Buildings and Simulations Fire safety of staircases in multi-storey buildings The results of measurements in Buildings and Simulations Grzegorz Kubicki, Ph.D. Department of Environmental Engineering, Warsaw University of Technology

More information

TLP Minimum tendon tension design and tendon down-stroke investigation

TLP Minimum tendon tension design and tendon down-stroke investigation Published by International Association of Ocean Engineers Journal of Offshore Engineering and Technology Available online at www.iaoejoet.org TLP Minimum tendon tension design and tendon down-stroke investigation

More information

Design and Analysis of Pressure Safety Release Valve by using Finite Element Analysis

Design and Analysis of Pressure Safety Release Valve by using Finite Element Analysis Design and Analysis of Pressure Safety Release Valve by using Finite Element Analysis Mr.V.D.Rathod* 1, Prof.G.A.Kadam* 2, Mr.V. G. Patil* 3 * 1 M.E. Design (Pursuing), SKN Sinhgad Institute of Technology&

More information

Modal Analysis of Barrels for Assault Rifles

Modal Analysis of Barrels for Assault Rifles PROBLEMS OF MECHATRONICS ARMAMENT, AVIATION, SAFETY ENGINEERING ISSN 2081-5891 2 (8), 2012, 7-16 Modal Analysis of Barrels for Assault Rifles Peter LISÝ, Mário ŠTIAVNICKÝ Academy of the Armed Forces of

More information

Copyright by Turbomachinery Laboratory, Texas A&M University

Copyright by Turbomachinery Laboratory, Texas A&M University Proceedings of the 2 nd Middle East Turbomachinery Symposium 17 20 March, 2013, Doha, Qatar Effectiveness of Windage Features on High Speed Couplings Steven Pennington Global Engineering Manager John Crane

More information

Finite Element Analysis of an Aluminium Bike Frame

Finite Element Analysis of an Aluminium Bike Frame Finite Element Analysis of an Aluminium Bike Frame Word Count: 1484 1 1. Introduction Each new bike model must pass a series of structural tests before being released for public retail. The purpose of

More information