UNIVERSITI TEKNIKAL MALAYSIA MELAKA

Transcription

1 UNIVERSITI TEKNIKAL MALAYSIA MELAKA MECHANISM DEVELPOMENT OF GRIPPER FOR 5KG PAYLOAD This report submitted in accordance with requirement of the Universiti Teknikal Malaysia Melaka (UTeM) for the Bachelor Degree of Manufacturing Engineering (Robotic and Automation) with Honours. by MOHD AHMAD SYAIHAN BIN LOKMAN FACULTY OF MANUFACTURING ENGINEERING 2010

2 UNIVERSITI TEKNIKAL MALAYSIA MELAKA BORANG PENGESAHAN STATUS LAPORAN PSM JUDUL: MECHANISM DEVELOPMENT OF GRIPPER FOR 5 KG PAYLOAD SESI PENGAJIAN: Saya MOHD AHMAD SYAIHAN BIN LOKMAN mengaku membenarkan tesis (PSM/Sarjana/Doktor Falsafah) ini disimpan di Perpustakaan Universiti Teknikal Malaysia Melaka (UTeM) dengan syarat-syarat kegunaan seperti berikut: 1. Tesis adalah hak milik Universiti Teknikal Malaysia Melaka. 2. Perpustakaan Universiti Teknikal Malaysia Melaka dibenarkan membuat salinan untuk tujuan pengajian sahaja. 3. Perpustakaan dibenarkan membuat salinan tesis ini sebagai bahan pertukaran antara institusi pengajian tinggi. 4. **Sila tandakan ( ) SULIT TERHAD TIDAK TERHAD (Mengandungi maklumat yang berdarjah keselamatan atau kepentingan Malaysia yang termaktub di dalam AKTA RAHSIA RASMI 1972) (Mengandungi maklumat TERHAD yang telah ditentukan oleh organisasi/badan di mana penyelidikan dijalankan) Disahkan oleh: (MOHD AHMAD SYAIHAN BIN LOKMAN) Alamat Tetap: NO 11, KG SIMPANG , TG MALIM PERAK Tarikh: (EN KHAIROL ANUAR BIN RAKIMAN) Cop Rasmi: Tarikh: * Jika laporan PSM ini SULIT atau TERHAD, sila lampirkan surat daripada pihak berkuasa/organisasi berkenaan dengan menyatakan sekali sebab dan tempoh tesis ini perlu dikelaskan sebagai SULIT atau TERHAD.

3 DECLARATION I hereby declare that this report entitled Mechanism Development of Gripper for 5Kg payload is the result of my own research except as cited in the references. Signature : Author s Name : Mohd Ahmad Syaihan Bin Lokman Date :

4 APPROVAL This report is submitted to the Faculty of Manufacturing Engineering of UTeM as a partial fulfillment of the requirements for the degree of Bachelor of Manufacturing Engineering (Robotic and Automation). The members of the supervisory committee are as follow: Supervisor En Khairol Anuar Bin Rakiman Faculty of Manufacturing Engineering

5 ABSTRAK Projek ini adalah berkaitan mekanisma dan pembangunan pencengkam dengan muatan 5kg. Penghasilan pencengkam memerlukan beberapa kajian dan analisis rekaan-rekaan yang telah wujud seperti penggunaan bahan, proses pembuatan dan sebagainya. Projek terdahulu telah dibuat dari segi reka bentuk dan analisa berkenaan pencengkam. Dalam projek ini, ia lebi fokus kepada proses yang terlibat di dalam pembangunan pencengkam proses seperti memilih proses bahan, proses yang terlibat dan proses pemasangan yang digunakan dalam penghasilan pencengkam. Komponen pencengkam yang dihasilkan digabungkan sehingga sebuah pencengkam yang lengkap dihasilkan. Kemudian ujian terhadap fungsi dan keupayaan pencengkam telah dibuat untuk memastikan pencengkam dapat bertahan dan berfungsi sepenuhnya. i

6 ABSTRACT This project is about on mechanism and development of gripper with 5kg payload. Gripper production need some study and analysis already existing designs such as material utilisation, manufacturing process etc. In chapter 1, it covering about introduction, project objective and scope the. Formerly, projects were made early in gripper design and analyzing about the gripper structures and functionability. In this project, its focusing on involved process research in gripper development process like material selection process, involved process and assembly process applies in gripper development. The gripper component is begin with fabrication of gripper mechanism following with the gripper assembly until the complete gripper was developed. Then the testing of gripper function and ability has been made to make sure the gripper is sustained and fully functional. ii

7 DEDICATION To my beloved family and friends. iii

8 ACKNOWLEDGEMENT There are many people who deserve thanks for the contributions they have made to this project. Firstly, I would like to express my endless grateful to my Final Year Project s Principal Supervisor, Encik Khairol Anuar Bin Rakiman. He directed and instructed me through every phase of the project, and his guidance has been invaluable. He also spent time and effort helping to resolve new issue by giving advice and suggestion as the project developed and checking the report a number of times. I would like to thank my beloved parent, for their abiding love and endless patience. Their support has been constant and enduring through the process of this project. They deserve an enormous amount of recognition for their moral support throughout this project. I am also grateful for all of my friends, who had giving their help and idea in completing this project. Finally, I am deeply indebted to the lab technician and all of the people that had directly or indirectly helped me during the period of completing the project. Thank you. iv

9 Abstrak Abstract Dedication Acknowledgement Table of Content List of Figure List of Table TABLE OF CONTENTS i ii iii iv v ix xi 1. INTRODUCTION Overview Problem Statement Objectives of the project Scope of Project 4 2. LITERATURE REVIEW Overview Operation Gripping Action External Gripping Internal Gripping Type of gripper Existing Gripper Analysis Major Factors in Choosing a Gripper and Jaw Design Tolerance Analysis Tolerance Analysis of Mechanisms Tolerance Type Major Factor Considerations in Manufacturing Gripper Material Selection Overview Cost Issues 15 v

10 Material Category 16 a) Plastics 16 i) High Density PolyEthylene (HDPE) 16 ii) PolyTetraFluorEtylene (PTFE) 17 iii) Neoprene 18 b) Metals 19 i) Aluminum 19 ii) Stainless Steel 20 iii) Mild Steel 21 c) Carbon Fiber Material comparison Manufacturing Process Selection Fabrication of Gripper Laser Cutting Machining (LCM) Electrical Discharge Machining (EDM) Turning Process Milling Grinding Drilling Fuse Deposition Modelling(FDM) Gripper Assembly Fastener 32 a) Bolt and machine Screw 32 b) Thread type Classification 33 i) Tapping Screw 32 ii) Slotted Screw 33 iii) Socket Head Cap Screw 34 c) Material Description of Screw Gripper testing Physical Prototype Testing Conclusion 36 vi

11 3. METHODOLOGY Introduction Project Planning Detail planning Study of Preliminary Design Finalize Conceptual Design Prototype Protoype Fabrication Process Assembly Process Prototype Functional Testing GRIPPER FABRICATION PROCESS Introduction Material Selection Bill of material Fabrication Process Flow Chart Overview Part 1: Base Fabrication Part 2: Link/Supporter Fabrication Part 3: Jaw Fabrication Assembly Process Gripper Assembly Mechanical Component GRIPPER FUNCTIONAL TESTING Overview Result Griper Feature Stability Low Cost Minimum Gripper Weight Flexibility Easy of Assembly or Disassembly 66 vii

12 5.4 Testing Ability of gripper to extend and retract Gripper lifting load Discussion Designing the gripper Fabrication process of gripper Gripper function and ability CONCLUSION AND RECOMMENDATION Conclusion Recommendation Design Aspects Mechanical Structure Aspects 74 REFERENCE 76 viii

13 LIST OF FIGURE Figure 2.1: Type of Gripper 8 Figure 2.2: The effect of an assign tolerance 11 Figure 2.3: Mathematical models of tolerance accumulation 11 Figure 2.4: Size Tolerance 13 Figure 2.5: Form Tolerance 13 Figure 2.6: Location Tolerance 14 Figure 2.7: Orientation Tolerance 14 Figure 2.8: Graph of Density (kg/m 3 ) Versus Young s Modulus (GPa) 15 Figure 2.9: HDPE material that use for base of the end arm 16 Figure 2.10: Application and product from PTFE material 18 Figure 2.11: Neoprene sheet 18 Figure 2.12: Robot end effectors that built using aluminum 19 structures as the main component Figure 2.13: Carbon Fiber Wheel Tubs (47" Dia.) 22 Figure 2.14: The comparison of the material that choosen in gripper fabrication 24 Figure 2.15: Example of piece of material that using Laser cutting 26 Figure 2.16: Turning process to manufacture shaft in accurate 28 shape and dimension Figure 2.17: Shaft usually using turning method to achieve 28 desires diameter and shape Figure 2.18: Milling process 29 Figure 2.19: Illustrated of the process at the cutting area 30 Figure 2.20: Illustrates a cross section of a hole being cut by 31 a common twist drill Figure2.21: Components for this robotic gripper were first prototyped, then manufactured,using FDM (Fused Deposition Modeling) 31 Figure 2.22: Example of bolt, machine screw 33 Figure 3.1: Flow of work process of developing gripper 38 ix

14 Figure 3.2: The first design of gripper 39 Figure 3.3: The finalize design of gripper 40 Figure 4.1: Gripper flow of fabrication process 48 Figure 4.2: Diagram of fabrication process of gripper 50 Figure 4.3: Base fabrication 51 Figure 4.4: Robot Mount fabrication 51 Figure 4.5: Grippert Mount fabrication 52 Figure 4.6: Supporter fabrication 53 Figure 4.7: Slider fabrication 53 Figure 4.8: Supporter + Base Bracket fabrication 54 Figure 4.9: Rod fabrication 54 Figure 4.10: Guide Bar fabrication 54 Figure 4.11: Guide Bar + Base Bracket fabrication 55 Figure 4.12: Finger holder fabrication 56 Figure 4.13: Finger fabrication 56 Figure 4.14: Holder fabrication 57 Figure 4.15: Pneumatic cylinder model SMC CQ1 61 Figure 4.16: Cylinder that mounting to the gripper 61 Figure 5.1: Conceptual design 63 Figure 5.2: The succesful gripper development 64 Figure 5.3: The gripper grasps the 1 kg sugar pack 69 Figure 5.4: The gripper ungrasps the 1 kg sugar pack 69 Figure 5.5: The gripper grasps the 2 kg sugar pack 70 Figure 5.6: The gripper ungrasps the 2 kg sugar pack 70 x

15 LIST OF TABLE Table 2.1: Summarize of part characteristics and associated 9 end effector solutions Table 2.2: International Tolerance (IT) grades 13 Table 2.2: Table of HDPE Properties 17 Table 2.3: Comparison of plastic that has been select for gripper fabrication 23 Table 2.4: Comparison of metal that has been select for gripper fabrication 24 Table 2.5: Material thickness requirement in LCM 26 Table 3.1: Example of machining process that use to machining parts 42 Table 4.1: Materials and components that used in gripper development. 46 Table 4.2: Gripper assembly process 58 Table 5.1: Gripper parts and function 66 Table 5.2: Gripper movement 68 xi

16 CHAPTER 1 INTRODUCTION 1.1 Overview The design of the end-of-arm tooling for a robotic assembly system is very important for reducing errors and decreasing cycle times. This is the piece of the robotic parts handler or assembler that physically interacts with the environment. While many factors may be blamed for the common failures of workcells, the culprit is very often the grippers. Well designed grippers can increase throughput, improve system reliability, compensate for robot inaccuracy, and perform value added functions to the assembly. According to dictionary of McGraw-hill(2003), gripper is define as a component of robot that grasp an object, generally through the use of suction cups, magnets, or articulated mechanism. Gripper provides the capacity to do a wide variety of manipulative task. Robotic hand or gripper is the integral part in most of the robot application. A robot arm itself can serve no purpose until a load or a tool is suspended from or attached to it. The robotic application in assembly and material handling is growing more rapidly in industrial environment. Thus, design of robotic gripping mechanism always becomes the key element for a specific operation. Guo et al, (1992) explained that the main function of a gripper is to grasp and to release workpieces during the material transfer route. Generally, the gripper for industrial robots is a specialized device that is used to handle only one or a few objects of similar shape, size and weight in a repetitive operation, which requires minimum gripping dexterity and is limited in its versatility. However, in other applications, the robot gripper will be 1

17 required to handle many different objects of varying weights, shapes, and material. Then, we shall refer to a more universal or versatile grippers. Gripper types will be discussed furthers in literature review. Arthur G. Erdman (1986) mention that the design of the gripper systems is not a trivial task. Unfortunately, the finalized parts and assembly sequence are often given to the designer, who must then devise grippers to handle the parts and perform the assembly. It is much more desirable for the design of the grippers to occur concurrently with the design of the rest of the system. Often a small feature added to a part can greatly increase the reliability of the gripper. Other times, a proper gripper design can simplify the overall assembly, increase the overall system reliability, as well as decrease the cost of implementing the system. The gripper is the mechanical interface between the robot and the work and the device with which the robot performs its programmed handling functions. Correctly selecting the gripper for an application is essential to the success of the application. Arthur G. Erdman (1986) explained that gripper selection is a may not be an easy task since there are wide variety of gripper types and configurations and many different factors to consider. Information on the factors which are relevant to the selection process is incomplete and tends to be qualitative. The material available and ease or manufacturing is also an important consideration. The end of the manipulator is the part the user or robot uses to affect something in the environment (Spencer, 2005). For this reason it is commonly called an end-effector, but it is also called a gripper since that is a very common task for it to perform when mounted on a robot. It is often used to pick up dangerous or suspicious items for the robot to carry, some can turn doorknobs and others are designed to carry only very specific things like beer cans. Even for semi-autonomous robots where a human controls the manipulator, using the gripper effectively is often difficult. For these reasons, gripper design requires as much knowledge as possible of the range of items the gripper will be expected to handle. Their mass, size, shape, strength, etc. all must be taken into account. 2

18 In this study, a robot gripper that has been design by the previous students is required be to fully analyses for its physical properties when handling load. Solid Work will be use as the analysis software for finite element analysis to the gripper. Finally, the gripper has to go through workspace testing by using simulation software to observe its performance in real time working situation. 1.2 Problem Statement The mechanism and development of robotic gripper is highly complex and environment dependent. To deal with complexity, the entire design project has to be broken down into several sub problems which are then treated independently as optimization problem. However, the constraints are generally dependent on each other. In this project, problem occur due finding the best way to fabricate the gripper. Furthermore, the existing design must be revised to mention the gripper able to grasp object with 5 kg payload. The study of this project is focus on improvement and continuation work on the previous PSM project which is a 10kg payload gripper for Comau robot. Then, study of the manufacturing process of the gripper and fabricate it. Basically the gripper design has been carried out in the last PSM. Since the current task is design analysis on 5kg payload gripper for Comau robot, this mean there would be a little improvement to the previous design and finally the gripper is fabricate assemble on Comau Robot. Often, very little time is spent in optimal kinematics structure design in the early stages of a design process. D. T. Pham (1988) describes that a time pressures sometimes force engineers to repeat topologies that have worked in similar application in the past rather than try to create better design. It is always encourages to follow the previous design unless the design analysis really proven that it was not good. Thus, modification and optimization are requires to upgrade the design to achieve a better performance. 3

19 Generally, a physical prototype is necessary to truly test a hand s ability to perform tasks, but this can be quite costly and design changes are not easy to make. Thus it would need a simulation system that able to load a gripper hand design, to interact with it and perform grasps of objects, and to visualize and evaluate the space of performance and error that might occurs. After simulation have been perform well, the design is fabricated and assemble it with Comau robot to done the task. 1.3 Objectives The objective of this project is to fabricate and assembled gripper to perform a pick and place operation for 5kg payload boxes. Below are important objective has to be achieved: a) To improve the design and relevent aspect. b) To develop the gripper prototype c) To carry out functional testing on the gripper 1.4 Scope The scope is focused on related aspect in this project so that the objectives are able to accomplish. Scope on this project will cover up the below task: a) Revisit the existing design b) Develop, fabricate and assembly the gripper. c) Testing the gripper performance and functional ability. 4

20 CHAPTER 2 LITERATURE REVIEW 2.1 Overview Motion devices imitate the movements of people, in the case of the gripper, it is the fingers. S. H. Yeo (1988) said that gripper is a device that holds an object so it can be manipulated. It has the ability to hold and release an object while some action is being performed. The fingers are not part of the gripper, they are the specialized custom tooling used to grip the object and was referred as a jaw In robotics, an end effector is a device or tool that's connected to the end of a robot arm where the hand would be. The end effector is the part of the robot that interacts with the environment. The structure of an end effector and the nature of the programming and hardware that drives it depend on the task the robot will be performing. In manufacturing, a robot arm can accommodate only certain tasks without changes to its end effector's ancillary hardware and/or programming. If a robot needs to pick something up, a type of robot hand called a gripper is the most functional end effector. If a robot needs to be able to tighten screws, however, then the robot must be fitted with an end effector that can spin. Maximum payload is the weight of the robotic wrist, including the EOAT and workpiece. It varies with different robot applications and models. 6

21 2.1.1 Operation The most widely used gripper is the pneumatically powered gripper; it is basically a cylinder that operates on compressed air. When the air is supplied, the gripper jaws will close on an object and firmly hold the object while some operator is performed, and then the air direction will change and the gripper will release the object. Typical uses are to change orientation or to move an object in a pick-n-place operation. 2.2 Gripping Action 2.2.1External: This is the most popular method of holding objects, it is the most simplistic and it requires the shortest stroke length. When the gripper jaws close, the closing force of the gripper holds that object Internal: In some applications, the object geometry or the need to access the exterior of the object will require that the object is held from the center. In this case the opening force of the gripper will be holding the object. 7

22 2.3 Types of Grippers The most popular types of grippers are the 2 jaw parallel and 2 jaw angular gripper styles. Parallel grippers open and close parallel to the object that it will be holding, these are the most widely used grippers. They are the simplest to tool and can compensate for some dimensional variation. Angular grippers move the jaws in a radial manner to rotate the jaws away from the object and therefore require more space. Figure 2.1: Type of Gripper (Yeo 1988) 2.4 Existing Gripper Analysis Major Factors in Choosing a Gripper and Jaw Design a) Part shape, orientation and dimensional variation Two jaw parallel gripper is desired if the object has two opposing flat surfaces, since it can handle some dimensional variation. Jaws can also be designed to handle cylindrical objects with the 2 jaw concept. Keep in mind that retention or encompassing grip requires much less force. 8

23 Table 2.1: Summarize of part characteristics and associated end effector solutions Part Characteristics Gripper Characteristics Large, heavy Grippers using wrap grips - taking advantage of friction or vacuum or electromagnetic holding Small, light Two-fingered gripper vacuum cup if smooth surface electromagnet if ferrous alloy Size, weight Shape Prismatic Two-fingered parallel-jaw gripper; angular motion if all parts have approximately same dimensions Cylindrical if light: use parallel or angular motion two-finger gripper with V- jaw fingertips if heavy: use wrap gripper - consider gripping on end with three-finger gripper if task or fixtures permit Flat Parallel or angular motion gripper or vacuum attachment Irregular Wrap grasp using linkages or bladder consider - augmenting grasp with vacuum or electromagnetic holding for heavy parts. Surface Smooth Good for vacuum attachments, simple electromagnets, twofingered grippers with flat fingertips Rough Compliant material (e.g., low durometer rubber) on fingertips or compliant membrane filled with powder or magnetic particles. - grippers that use a wrap grasp are less sensitive to variations in surface quality. Slippery Consider electromagnet or vacuum to hold - grippers that use a wrap grasp are less sensitive to variations in friction Material Ferrous Electromagnet - concerns that do not rule out the presence of strong magnetic fields Soft Consider vacuum or soft gripping materials Very delicate Soft wrap grippers and vacuum grippers so can grip gently - compliant fingertips with foam rubber use to distribute the contact pressure if the part is very light and fragile consider lifting it using the Bernoulli effect b) Gripper Weight: Grip force must be adequate to secure the object while a desired operation is performed on the object. The type of jaw design must be part of the force requirement. Keep in mind that you should add a safety factor to the amount of force that you select and air pressure is a factor to keep in mind. 9

24 c) Accessibility This applies both to the work being performed on the object and the amount of room for the gripper jaws. If the work is to the exterior of the object then it may require an internal grip. Angular grippers are usually less expensive but require additional space for jaw movement. d) Environmental Harsh environment or clean room applications require grippers designed for those purposes. e) Retention of the Object When air pressure is lost, the gripper will relax its grip on the object and the object may be dropped. There are spring assist grippers designed for this type application Tolerance Analysis Alan R. Parkinson (1991) in his articles mentioned that tolerance management is a key element in their programs for improving quality, reducing overall costs and retaining market share. The specification of tolerances is being elevated from a menial task to a legitimate engineering design function. New engineering models and sophisticated analysis tools are being developed to assist design engineers in specifying tolerances on the basis of performance requirements and manufacturing considerations. Koenderink and van Doorn (1987) performed a tolerance analysis to measure the extent to which certain information is available in velocity flow fields 10