V-Tail Flamingo. Included in Kit * Pre- cut balsa parts * Ballast weights * Diagram sheet * Sandpaper sheet
|
|
- Sheryl Blair
- 5 years ago
- Views:
Transcription
1 V-Tail Flamingo Included in Kit * Pre- cut balsa parts * Ballast weights * Diagram sheet * Sandpaper sheet Additional Items You May Need * Wood Glue * Epoxy Glue * Sanding block * Hobby knife Overview: The Flamingo is a classic, sleek V-tail design with double dihedral wings. The wings are made from balsa, and the body parts are made from Paulownia wood (similar to balsa but stronger). It features a very straight forward construction with minimal parts. Skill Level: This model is suitable for intermediate to advanced builders. Although the design itself is very simple, there are no pre-cut guides and supports for wings or tailplane. This requires some skill to sand, prop and glue the parts together. Also, there is no angle of incidence built in to the wing and tail mounts. So your building skills and airframe knowledge will be applied to adjusting the tailplane angle to give the optimal flight path.
2 Build Procedure Firstly it s a good idea to tape down a sheet of cling wrap over your work surface. This will stop the parts from becoming glued to the surface. It s easier to peel off cling wrap from any wooden parts. Note: although the kit is supplied with CA glue, we recommend using other glues which are suitable for balsa wood if available. Glue one of the side pieces onto the main body spar. Add the ballast nuts into the nose cavity. Note: This kit may be supplied with either nuts or ballast lead shot. Glue on the other side piece. make sure that the side with the canopy marking is facing out as this side also has a small marker line behind the canopy to show where the leading edge of the wing goes. Cut the wing tips completely off the main wing with a hobby knife.
3 Sand the edges of the wing tips as well as the tailplane pieces at a slight angle so they fit together flush. Refer to the diagram below to set the height of the wing tips and glue them in place. You will need to support them with something till they are completely dry. Wing tip is 30mm above the surface Do the same with the tailplane surfaces. Tail-plane tips are 30mm above the surface If you intend to sand down the body and wing pieces then now would be a good time to do it. Sand down the leading and trailing edge of the wings at a shallow angle leaving an edge which is about 0.5mm thick, and then round them off to form a slight airfoil shape. Don t sand the top of the body section in the areas where the wings and tailplane will attach. When the previous step has fully dried, sand the centre joins of the wings at a very slight angle and glue together, once again supporting the wing tips while the whole wing dries. The wing tips should be 48mm above the surface.
4 Attach the wings to the main body. You will need to use some bluetack or putty to hold the main body frame and also support the wings with something while they dry. Make sure the wings are the same height on either side. There are marks on the body to show where the wings attach. Leading edge of the wing lines up with this mark. Epoxy would be a good choice of glue to use here. Do not glue on the tailplane yet. Once the wings are dry you may want to add some more glue along the joint under the wings for additional strength. This also applies to the joins in the wings and tail section. You may wish to cut a piece of cardboard this shape to use as a balance to check the COG. Tape the cardboard shape to the edge of a work bench and use it to balance the glider. Attach the tailplane with masking tape for the moment for checking the balance point. The ideal balance point should be 40 mm from the leading edge of the wing at the root. You may need to remove the tail, trim the tail shaft shorter and re-attach the tail with masking tape till you get the balance right. 40mm
5 Balanced! But don t glue on the tailplane yet. The kit doesn t include any pre- set angle of attack between the wings and the rear part of the tail shaft. You will need to sand down the front of the tailplane seat to give this angle. Use a sanding block and aim to drop the front down about 2mm. Tape the tailplane in place securely with masking tape and test glide till you have the plane all set up and balanced correctly with the desired angle of attack between the tailplane and wings. Set up a jig to hold the plane and tailplane in place and glue on the tailplane. See a test flight video on YouTube (LINK) Copyright MicronWings 2015: All rights reserved. This manual is for personal use only. No unauthorized copying or digital distributing permitted without permission from MicronWings.
Your kit contains the following items. Additional Items You May Need. Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet
Your kit contains the following items Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet The SkyFox offers great glide performance in a rubber powered plane due to its built up wing.
More informationaero naut Electric Model Aeroplane Quido Order-No. 1303/00
aero naut Electric Model Aeroplane Quido Order-No. 1303/00 Quido is a small model that accompanies you wherever you go. The prefabricated parts are mostly balsa and just need to be assembled according
More informationGeneral Build Instructions for Mach 1 BT50 and BT55 Single Fin Kits. Needed Items for Assembly
General Build Instructions for Mach 1 BT50 and BT55 Single Fin Kits 60-80 grit sandpaper Hobby knife Tape measure Scissors CA Super glue 30-minute epoxy 5-minute epoxy Masking tape 1/16 drill bit Needed
More informationANGEL 2000 glider ARF ASSEMBLY MANUAL. Specifications: MS: 129
WWW.SEAGULLMODELS.COM ASSEMBLY MANUAL ANGEL 2000 glider Graphics and specifications may change without notice. MS: 129 ARF Specifications: Wingspan---------------78.7 in ( 200cm). Wing area---------------582.8sq.in
More informationLittle Dog Dual Deploy
Little Dog Dual Deploy John Wilke & Paul Fechtmeister September 2010 All dimensions are in inches unless specified Construction Notes: Other items you will need: One set of epoxy Motor One sheet of 120
More information1939 STOUT TROPHY WINNER
1939 STOUT TROPHY WINNER This model's 36-minute flight won the Stout Trophy and qualified the builder as captain of the American Moffett team. Bob Toft. Has won a second in gas, first in rubber at Nationals.
More informationModel Aero Sportster Indroduction
1 Model Aero Sportster Indroduction We are excited to introduce the Model Aero Sportster! Inspired by classic designs of the past, the Sportster is a relaxing slow flyer, equally at home indoors or outside
More informationAegea Assembly Notes:
Aegea Assembly Notes: The Aegea model is a thermal Duration (TD) model made up of components from Phil Barnes 1 (bagged wing and tail group) and Terry Luckenback 2 (Pretty Mantis fuse). Due to its construction
More informationBuilding Instructions ME 163 B 1a M 1:5 Turbine
Building Instructions ME 163 B 1a M 1:5 Turbine Thank you for choosing our kit of the Me-163B. We ask you to read the instruction once in advance before building this kit in order to avoid mistakes. Make
More informationrobart HOW-TO Series Model Incidence Meter
robart HOW-TO Series Model Incidence Meter The term incidence is something of a misnomer since this highly versatile tool is capable of measuring or comparing angles other than incidence of a wing or tail.
More informationAkcent-2 - Building Instructions
Akcent-2 Home Pictures Building Instructions Ordering Akcent-2 - Building Instructions Note! The pictures show older kits with "diser" wings. The new kits come with nicer D-box wings. Servo locations are
More informationLast Revised 3/17/15 RMRC Mako
Ready Made RC, LLC Assembly Instructions for: Last Revised 3/17/15 RMRC Mako Page 1 Thank you for purchasing the RMRC Mako! It is important to read the manual in its entirety before your maiden flight.
More informationH ow To Buil d A Wa ter Rocket
H ow To Buil d A Wa ter Rocket DESIGN AND DEVELOPMENT Brainstorm The first step in the design of a water bottle rocket is brainstorming. Brainstorming is a problem-solving technique that involves the spontaneous
More informationBlazer Marine, Whiplash Sport 40
Blazer Marine, Whiplash Sport 40 Thank you for choosing to build the Whiplash 40. We have spent over 12 years perfecting this design, and finally we are making it available to the world. We are excited
More informationFlyingFoam Nurf. General Assembly Instructions
FlyingFoam Nurf General Assembly Instructions These instructions apply to the Nurf, an all EPP forward swept flying wing available from FlyingFoam.com. Building and operating a remote controlled aircraft
More informationHow To Build A Water Rocket
How To Build A Water Rocket DESIGN AND DEVELOPMENT Brainstorm The first step in the design of a water bottle rocket is brainstorming. Brainstorming is a problem-solving technique that involves the spontaneous
More informationInstructions for Fun Foam Critter 4/25/2007 BP Hobbies LLC 140 Ethel Road W Suite J Piscataway NJ,
Instructions for Fun Foam Critter 4/25/2007 BP Hobbies LLC 140 Ethel Road W Suite J Piscataway NJ, 08854 http://www.bphobbies.com Specifications: Wing Span: 20" Length: 20" Flying Weight: 5.5-7.0 oz Controls:
More informationModel Aero AT-6 Texan Introduction
1 Model Aero AT-6 Texan Introduction We are excited to introduce the Model Aero AT-6 Texan! Originally used as an advanced trainer by the U.S. Armed Forces, the AT-6 is a relaxing slow flyer, equally at
More informationOutbound Progress Report
Outbound Progress Report 7-11-17 Tank Install The new 20 plus gallon fuel tank is underway. In a matter of weeks we should be getting the first article and placing a first run order. The tank fits like
More informationWHAT IS GLIDER? A light engineless aircraft designed to glide after being towed aloft or launched from a catapult.
GLIDER BASICS WHAT IS GLIDER? A light engineless aircraft designed to glide after being towed aloft or launched from a catapult. 2 PARTS OF GLIDER A glider can be divided into three main parts: a)fuselage
More informationConstruction Chapters Index
Construction Chapters Index 9 7 8 Chapters Index c. c. c. c. c. c. c7. c8. c9. c0. c. c. c. c. c. c. c7. Balsa Wood Skeleton Strip Planking Hull Fairing Keel Bulb Mould Lead Bulb Casting Keel Construction
More informationDesigned by Steve Shumate Adapted from the North Star design by Laddie Mikulasko. Polaris EX Introduction
1 Model Aero Polaris Designed by Steve Shumate Adapted from the North Star design by Laddie Mikulasko Polaris EX Introduction We re excited to introduce the Polaris EX seaplane parkflyer! Based on the
More informationBlazer Marine, Whiplash Sport Hydro
Blazer Marine, Whiplash Sport Hydro Thank you for choosing to build the Whiplash Sport Hydro. We have spent over 12 years perfecting this design, and finally we are making it available to the world. We
More informationX-29 Canard Jet. A Simple Depron Foam Build.
X-29 Canard Jet. A Simple Depron Foam Build. Two full sized X-29 s were built and the first flew in 1984. They were experimental aircraft, testing this unusual configuration of a canard jet with swept
More informationWHITE WOLF. X-ray View MID POWER MODEL ROCKET KIT BUILDING INSTRUCTIONS KIT SPECIFICATIONS:
WHITEWOLF-38 PARTS LIST 1 - Nose Cone 1-17" Airframe 1-6" Motor Tube 3 - Aft Fins 3 - Forward Fins 2 - Centering Rings 1-15" Parachute 2 - launch lugs 1-12 Kevlar Shock Cord 1 - Motor Retention >>(screw/washer)
More informationMICRO - DLG. This kit should only take 30 minutes to compile, very simple and quick.
MICRO - DLG This kit should only take 30 minutes to compile, very simple and quick. You will need: Hot Glue ( small tip preferably ) Sharp razor blade Ruler a strip of strong fiber tape Thin nose Pliers
More informationBuild This World Record Fuselage Model
Build This World Record Fuselage Model Here You Have Complete Instructions and Plans to Build a Plane of Sure-fire Performance that Established a World Record at the 1932 National Airplane Model Competition
More information" A " "B " F G H P PARTS LIST
K-57 SkyDart usiness SST Concept SUSIDIRY OF DMON ESTES INDUSTRIES PENROSE COLO. 8120 Designed by Larry H. Renger "G " " " " F " R "H " SP-57 U " " "C " I M C O T T L "D " E F G H P D J "E " N K Q S 1
More informationWe hope you ll enjoy the Drifter as much as we have! Scott DeTray Model Aero Specifications:
We are excited to bring you the Drifter RC airboat. You re probably thinking it doesn t fly so what is Model Aero thinking??? We have always liked RC vehicles of all types and have had a fondness for airboats
More informationAGM 33 PIKE ALL FIBERGLASS. Specifications Length: 92 Diameter 5.5 Weight: 24 lbs Motor Mount: 75mm Fins: 6-3/16 G10 CP: 68 from nose tip Parts List
ALL FIBERGLASS AGM 33 PIKE Specifications Length: 92 Diameter 5.5 Weight: 24 lbs Motor Mount: 75mm Fins: 6-3/16 G10 CP: 68 from nose tip Parts List (1) Filament Wound Nose Cone w/ Metal Tip (1) Nose Cone
More informationMiss Mayflower. Build Manual
Miss Mayflower Build Manual Thank you for the purchase of the Miss Mayflower, this new exciting craft will give you fun on many types of terrain including snow, gravel, pavement, grass, water, and when
More informationAliphatic Resin Wood Glue. 18" Fabric Parachute Part #PNC50 Part # Part #11700 Part #J0016. Launch Lug
ADANCED * What you will need to build the Quest High-Q Hobby Knife * Straight Edge Pencil Aliphatic Resin Wood Sanding Sealer & Brush Spray Paint Parts and exploded view of the Quest High-Q Nose Cone 18"
More informationSTUDY GUIDE A Day By Day Course Refreshment Quiz To Ensure That You Make The Most Out Of Your Rod Building Class
DAY ONE: 1) Why would you want to build your own fishing rod? a. It s fun and rewarding b. You can customize your rod to your needs c. You can save money d. All of the Above 2) The main part of a fishing
More informationPrinciples of glider flight
Principles of glider flight [ Lecture 2: Control and stability ] Richard Lancaster Email: Richard@RJPLancaster.net Twitter: @RJPLancaster ASK-21 illustrations Copyright 1983 Alexander Schleicher GmbH &
More informationAVA Building Instructions
Suggested Assembly Sequence: AVA Building Instructions 1. Insert fittings in rudder and trial fit rudder on boom 2. Attach stab to v-mount and position ahead of rudder ¼, sanding the v-mount as needed.
More informationBob's Card Models and [Resources]
Bob's Card Models www.bobscardmodels.altervista.org and www.zealot.com [Resources] Robin DR400-140B Major 1:25 The Robin sport monoplane, conceived by Pierre Robin and Jean Délémontez. The Robin DR400
More informationSoling Building Tips II
Soling Building Tips II Prepared: Arthur Deane Jan 20, 2002 adeane@ic.net Introduction The following are some lessons learned and experience gained in building a Soling kit. The plan developed is based
More informationA Table Top Wind Tunnel You Can Build
A Table Top Wind Tunnel You Can Build Basic principles of aerodynamics can be studied in the classroom with this simple, inexpensive wind tunnel. All you need to build it is some cardboard boxes, glue,
More informationMiG-29 Scale EDF Radio Control model airplane
MiG-9 Scale EDF Radio Control model airplane Wingspan : 45mm Model No : FF-D004 UNDER SFETY PRECUTIONS This radio control is not a toy! - lways keep this instruction manual ready on hand for quick reference.
More informationInsanity is doing the same thing over and over again and expecting a different result
ZIROLI P40 KITTYHAWK Insanity is doing the same thing over and over again and expecting a different result I have built four Ziroli Kittyhawks over the past umpteen years and this is a picture of the fourth
More informationHorizontal Fuselage. Top Vertical Fuselage 1. Lay out the Top Vertical Fuse Front(1), Top Vertical Fuse Back(2), and Vertical Stabilizer(3).
Rumbuilder 71 B-17 Congrats on your Rumbuilder B-17! We re glad you chose to fly with us! If you have any problems, or missing/broken kit pieces, please contact us. We d be happy to replace any damaged
More informationSEAGULL SPORT FLYING BOAT BY IVAN PETTIGREW CONSTRUCTION NOTES
SEAGULL SPORT FLYING BOAT BY IVAN PETTIGREW CONSTRUCTION NOTES The Seagull came into being in 1994. Often when camping at a peaceful lake I thought it would be nice to have a quiet electric glider in order
More informationFoam Plate Glider: Sonic Silhouette
Designed by: Ritchie Kinmont Project #40 Page 1/25 Foam Plate Glider: Sonic Silhouette About this project: The Foam Plate Glider Sonic Silhouette is the first in a series of flying glider projects made
More informationThe author's TD Coupe, used as a towplane, and the Airhopper. The gas model is equipped with an automatic towline release.
THE AIRHOPPER BY STANLEY ORZECK PLANS BY PAUL PLECAN An eight-foot sailplane either towed by a gas model or launched by hand tow. The author's TD Coupe, used as a towplane, and the Airhopper. The gas model
More informationMain Wing Wood Parts
Main Wing Wood Parts WR 1-11 TE LE MS1 MS2 ST MS3 Before you start the build, gather all the required main wing components. QTY o MS1 (Main Spar 1) 2 o MS2 (Main Spar 2) 2 o MS3 (Main Spar 3) 2 o ST (Servo
More informationTLC Technology Education Draft
TLC Technology Education Draft Title: Airplane Design, Construction, and Flight State Standards: C Explore current transportation technologies and their impacts on society and the environment. C Explore
More informationLearning to Fly: The Wright Brothers Adventure EG GRC 39
Learning to Fly: The Wright Brothers Adventure EG 2002 12 007 GRC 39 The Wright Brothers 1900 aircraft was flown repeatedly at Kitty Hawk, North Carolina, during the fall of 1900, mostly as a kite but
More informationPre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender
Pre-Paint>Fuselage>Empennage>Fit vertical tail fin Objectives of this task: To fit the vertical tail fin to the fuselage, including fitting the static probe, static tube, optional strobe light wiring and
More informationPUT TING SCIENCE TO FLIGHT T E A C H E R S G U I D E
PUT TING SCIENCE TO FLIGHT T E A C H E R S G U I D E Rocco Fer rario Teacher, American Canyon Middle School Napa, CA 55747 TECH TIPS Building Tips for the Raven Broken wings are a bummer. Unless the dihedral
More informationSlipso400 August 17, 2006
Slipso400 August 17, 2006 Contents 1 Introduction 3 2 Preparation 4 3 Wing 5 3.1 Preface.............................................. 5 3.2 Building.............................................. 5 3.2.1
More informationVortex Generator Installation Addendum
1 Introduction The Zlin Aviation, s.r.o. Kit, when installed in accordance with these instructions and other applicable data, results in better handling, a lower stall speed, and more controllable flare
More informationPanoptix PS51-TH FrontVü/LiveVü Thruhull
Panoptix PS51-TH FrontVü/LiveVü Thruhull Transducer Installation Instructions Important Safety Information WARNING See the Important Safety and Product Information guide in the chartplotter or fishfinder
More informationIt is also possible to make a more traditional version of the design - which I call Easy Glider - which can be launched by hand in the normal way.
The Kendal Flyer Designed by David Mitchell The Kendal Flyer is a rubber band launched plane that I designed in 1990. It is possible to make a pure origami version but I prefer this one in which the nose
More informationIVAN S LAKEMASTER BY IVAN PETTIGREW CONSTRUCTION NOTES
IVAN S LAKEMASTER BY IVAN PETTIGREW CONSTRUCTION NOTES August 2015 The LakeMaster started out to be a scaled down version of Ivan s Seagull which has been a fantastic model for over 20 years. The Seagull
More informationAnnex E(M) - Final inspection checklist - monowheel
Annex E(M) - Final inspection checklist - monowheel A/C Reg... Owner...Kit S/N...Date... (U.K. Only) L.A.A No...Inspector...Insp. No... Note: This check list only covers specific items for inspection of
More informationWhisper 1400 Glider Operation Manual
Whisper 1400 Glider Operation Manual Specifications: Wingspan: 55 (1400mm) Length: 32.5 (825mm) Wing area: 323 sq. in. Weight: 16 oz.(453g) Ace R/C Whisper 1400 Glider R/C Sailplane (4104-F) Distributed
More informationCONSTRUCTION NOTES BY: MARK HUNT ISSUED:
INSIGHT V4 CONSTRUCTION NOTES BY: MARK HUNT ISSUED: 3/22/06 Pg.1 INDEX Title Page 1 Index 2 Introduction 3 Material list 4 Foam Cutting Notes 5 Wing 5 Stab 8 Vertical Fin 8 Fuselage Foam Parts 9 Fuselage
More informationBASIC AIRCRAFT STRUCTURES
Slide 1 BASIC AIRCRAFT STRUCTURES The basic aircraft structure serves multiple purposes. Such as aircraft aerodynamics; which indicates how smooth the aircraft flies thru the air (The Skelton of the aircraft
More informationMax Bee. Part II: Building Max Bee Stunt News 8. lighter: the building of Max. all published.
Max Bee Can you say Exotic? Igor s World Championship winning design has lots of interesting aerodynamics as well as interesting aesthetic design cues. I know, I know, the designing article about Max Bee
More informationDornier Do R 4 Super-Wal
Dornier Do R 4 Super-Wal Model Aviation Laddie Mikulasko s Dornier Do R 4 Super-Wal Build the multiengine, record-setting seaplane. Article, plans, instructions, and photos by Laddie Mikulasko. Complete
More informationSo at 18%, the weight of our 50 Hawk should around the 8lb mark I ll let you know later if this was achieved.
50 DUCTED FAN HAWK It was in 2015 when the first Hawk offering was made to the readership of the RCM&E and it proved to be a great success especially when we made the ducted fan installation a lot simpler
More informationStep 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the seam joint is.
WhiplashGV Instruction Manual Email: Brian@Blazermarine.com Phone: 513-598-1769 Step 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the
More informationBlaster 2 & 2e Assembly Guide
Blaster 2 & 2e Assembly Guide from 123 Radford Road Leamington Spa Warwickshire UK CV31 1LG www. sales@ 2009 HyperFlight Revision 5, 1/05/09 R5.odt Warning, this is not a toy! If you are new to the hobby
More informationFOOTE'S "WESTERNER" RECORDS MORE THAN TWENTY FIRST PLACES TO DATE.
FOOTE'S "WESTERNER" THIS 7' CLASS C CONTEST WINNER IS THE MOST OUTSTANDING DESIGN THAT HAS BEEN DEVELOPED SINCE THE PYLON ERA. BUILD ONE NOW, TO ASSURE YOUR SHARE OF TROPHIES IN POSTWAR CONTESTS. RECORDS
More informationPAY N PAK, 1/12 th Scale, Limited Sport Hydro P Sport Hydro
1980 82 PAY N PAK, 1/12 th Scale, Limited Sport Hydro P Sport Hydro Introduction: The 1980 turbine Pay N Pak is a good subject for a model race boat. It has a low profile, mild pickle-fork setback, long
More informationBUILDING INSTRUCTION Glider TASER unplugged. Taser unplugged Building instruction September
Wingspan [mm]: 2000 Takeoff weight [g]: From 400 Airfoil: AG 455ct-02f AG47ct-02f by Mark Drela BUILDING INSTRUCTION Glider TASER unplugged www.pcm.at 1 CONTENTS DATA 1. Kit contents 2. What else do you
More informationMiniTwin by Acer
MiniTwin 250 - by Acer ASSEMBLY INSTRUCTIONS Thank you for choosing the MiniTwin 250 as your next project. This kit is easy to build and only requires a few hours to complete. Once finished, you will be
More informationDe Havilland 100 FB9Vampire
De Havilland 100 FB9Vampire Well this is a first you maybe thinking, finally a model plan specifically designed for turbine. Your next question might be, why it has taken so long for this to happen. Well
More informationGLIDING NEW ZEALAND ADVISORY CIRCULAR MYLAR SEALS. This is an Uncontrolled Document. Issued September 2004
GLIDING NEW ZEALAND ADVISORY CIRCULAR MYLAR SEALS This is an Uncontrolled Document Issued September 2004 Holder s Name: Address: COPYRIGHT 1999 GLIDING NEW ZEALAND INC. No part of this Advisory Circular
More informationADVENTURES WITH. Both of my grandfathers fished, my dad fished, and. creating unique handles for custom rods. 22 RodMaker
From RodMaker Magazine Volume 7 Issue #4 WOOD creating unique handles for custom rods ADVENTURES WITH story by Ray Jergensen photos by Les Jergensen 22 RodMaker Both of my grandfathers fished, my dad fished,
More informationFauvel AV36 tailless glider Scale 1:16
Fauvel AV36 tailless glider Scale 1:16 F11 (Page 1) Original colours: RAL 2009 RAL 6017 (Page 2) F9 F10 RAL 3020 RAL 7047 F4 F5 F8 F1 Abbreviations used for numbering parts: A = wings ( ailes ) D = empennage
More informationWowings Booby CONSTRUCTION MANUAL. Copyright 2005 Wowings
Wowings Booby CONSTRUCTION MANUAL Copyright 2005 Wowings www.wowings.com - 1 - Thank you very much for purchasing the Booby. Although made primarily of soft EPP foam, this RC slope glider is still capable
More information5. Tailplane assembly
5. Tailplane assembly Overview This section covers the fitting of your completed tailplanes to the torque tube assembly. Included is the insertion of the TP13 bushes in the inboard rib and the fitting
More informationPitts Model 12 Wing Leading edge Installation
Pitts Model 12 Wing Leading edge Installation This procedure is used to install molded plywood leading edges included in the Pitts Model 12 kit. Nine (9) molded leading edge section are require per aircraft;
More informationWE GET PEOPLE FLYING INSTRUCTION MANUAL
TM WE GET PEOPLE FLYING INSTRUCTION MANUAL 90% pre-built Pre-covered in Goldberg UltraCote transparent blue and white covering Includes sailplane hardware package with adjustable tow hook Superb stability
More informationTrimming and Flying a Hand Launch Glider A basic and beginners guide by Kevin Moseley
Trimming and Flying a Hand Launch Glider A basic and beginners guide by Kevin Moseley First and foremost, I am by no means a master at what I have done, or do, in hlg or the class. I am fortunate enough
More informationAerodynamic Terms. Angle of attack is the angle between the relative wind and the wing chord line. [Figure 2-2] Leading edge. Upper camber.
Chapters 2 and 3 of the Pilot s Handbook of Aeronautical Knowledge (FAA-H-8083-25) apply to powered parachutes and are a prerequisite to reading this book. This chapter will focus on the aerodynamic fundamentals
More informationPT 11 trouble-shooting and maintenance.
PT 11 trouble-shooting and maintenance. Does your rudder not stay down?...your back seat slip off?...your knobs tight and your leather pads loose? Maybe we can help. We have used our PT 11 s hard enough
More informationKWARCINSKI MODELS STARLING PRO. by Klaus Weiss. The Kit:
KWARCINSKI MODELS STARLING PRO. by Klaus Weiss I had been looking at the Starling, fully moulded glider, for some months now, so it was a pleasant surprise to be in the position to write a review of this
More informationFlying Wings. By Henry Cole
Flying Wings By Henry Cole FLYING WINGS REPRESENT THE THEORETICAL ULTIMATE IN AIRCRAFT DESIGN. USE THESE IDEAS, AVAILABLE AFTER A YEAR, OF RESEARCH, TO DEVELOP PRACTICAL MODELS. The rubber version of this
More informationESOCCI RIGGING MANUAL
ESOCCI RIGGING MANUAL 1 Spray Covers Hull Rear Iako Forward Iako Ama ESOCCI RIGGING MANUAL 2 When training & racing in outrigger canoes, the canoe is your protector on the water and therefore it is imperative
More informationThe Addition of Vortex Generators for STOL performance and or for Meeting the Light Sport Aircraft Rules
The Addition of Vortex Generators for STOL performance and or for Meeting the Light Sport Aircraft Rules This modification allows the Europa XS or Classic aircraft to operate with a greater stall margin
More informationGrandpa's Homemade Rocket for About a Dollar!
Grandpa's Homemade Rocket for About a Dollar! Grandpa and Granny Co. 2012 The most common items needed: (The number of Rocket parts from each item is before the parts name and its proportionate cost is
More informationTheory of Flight Aircraft Design and Construction. References: FTGU pages 9-14, 27
Theory of Flight 6.01 Aircraft Design and Construction References: FTGU pages 9-14, 27 Main Teaching Points Parts of an Airplane Aircraft Construction Landing Gear Standard Terminology Definition The airplane
More informationHalifax MkIII Heavy Bomber
Halifax MkIII Heavy Bomber For every decorated hero there are always the un-sung heroes and for every wartime aircraft there those that are remembered and those which are forgotten about and never really
More informationFigure 8: Looking Down on a Three Thruster Vehicle
Moving and Maneuvering 2 Cornerstone Electronics Technology and Robotics III (Notes primarily from Underwater Robotics Science Design and Fabrication, an excellent book for the design, fabrication, and
More informationCIRCLING THE HOLIGHAUS WAY -
CIRCLING THE HOLIGHAUS WAY - OR DO YOU REALLY WANT TO KEEP THE YAW STRING CENTERED? BY RICHARD H. JOHNSON ANSWERS: 1. During Straight Flight - YES, that minimizes drag and maximizes the sailplane's performance.
More informationSTOL CH V10-4SP Jury Strut Angle. Position the jury strut angle at rib station #2 (drawing 7-V-10) drill and Cleco.
7V10-4SP Jury Strut Angle Position the jury strut angle at rib station #2 (drawing 7-V-10) drill and Cleco. SECTION 4C - Page 1 of 11 SECTION 4C - Page 2 of 11 Turn the wing over. 7V7-1 Nose Skin TIP:
More informationMiles M-57 Aerovan. Ok so on with the build.
Miles M-57 Aerovan Now it s been a few years since I have produced a design for Model World so young Mr Van Geffen decided I had sat on my laurels for too long and it was time to get the thumb screws out
More informationVALDIVIA BUILD LOG Dr Ron
VALDIVIA BUILD LOG Dr Ron The Robbe kit of the two-masted schooner Valdivia was purchased in 2007, along with the fitting set and propulsion accessories, and has been staring me in the face since then
More informationBUILD AND TEST A WIND TUNNEL
LAUNCHING INTO AVIATION 9 2018 Aircraft Owners and Pilots Association. All Rights Reserved. UNIT 2 SECTION D LESSON 2 PRESENTATION BUILD AND TEST A WIND TUNNEL LEARNING OBJECTIVES By the end of this lesson,
More informationAerobatic Trimming Chart
Aerobatic Trimming Chart From RCU - Chip Hyde addresses his view of Engine/Motor thrust. I run almost no right thrust in my planes and use the thottle to rudd mix at 2% left rudd. to throttle at idle.
More informationCARL GOLDBERG PRODUCTS, LTD. P.O. Box 818 Oakwood GA Phone # Fax #
Superfloats 36 ARF WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that could
More informationLower Surface Leading Edge Tape
Lower Surface Leading Edge Tape Glider Performance Modification Jim Hendrix The Deturbulator Project www.deturbulator.org Revised 10/15/2012 Overview The Deturbulator Project (www.deturbulator.org) has
More informationDarling Downs Soaring Club Inc
Darling Downs Soaring Club Inc Rigging and De-Rigging Instructions LS7 XOW Overview Page 2 Rigging page 3 De-Rigging page 19 Overview It is the pilot s responsibility to make sure that the trailer is fully
More information1/10 th Scale 1956 Ted Jones Classic Hydroplane
1/10 th Scale 1956 Ted Jones Classic Hydroplane Preparation These plans show outside sheeting of 3/32 balsa laminated with 1/64 birch ply. This makes a light and strong skin for this boat. Optionally you
More informationISSUE 404 NOV IN THIS ISSUE. Fixing Broken Fins.
ISSUE 404 NOV 17 2015 IN THIS ISSUE https://www.apogeerockets.com/rocket-kits/skill-level-4-model-rocket-kits/2-6in-tomach By Tim Van Milligan Every time I take my daughters to a rocket competition, we
More informationRATLINER Assembly Instructions.
Model Shipways Inc. www.modelexpo-online.com RATLINER Assembly Instructions. Patent Pending 1. Remove center stands and braces from the main rigging frame. 2. The Stands and Braces should press release
More informationSnowbird Stick Job. by Alan Orthof
Snowbird Stick Job by Alan Orthof After AI Orthof hoiked his big dogs into galoshes the other day to plod through the first snow of the season, he realized that models need winter boots, too. So he got
More informationSTEP 1 A. Lay the two Motor Mount Tubes on a flat surface with ends even and Glue them together with White Glue. Allow Glue to set before moving on.
Prod. No. A51003 Skill Level Three QUEST AEROSPACE, INC PO Box 2409 Pagosa Springs, CO 81147 800-858-7302 Things You ll Need To Assemble this Kit: Pencil and Hobby Knife: White Glue: Aliphatic Resin glue,
More information