Marlinespike Seamanship
|
|
- Conrad Glenn
- 5 years ago
- Views:
Transcription
1 20 Marlinespike Seamanship 157 Section 20 Marlinespike Seamanship Becket. An eye in the end of a block used for securing an end of a line; an eye in the end of a rope. Bend. To make fast a sail to a spar or stay. Also, a knot to secure a line to another line or object. Bight. Open or closed loop in a line or rope. Fid. Tapered tool used in splicing. Hitch. A knot used to secure a rope fast to another rope or to other object. Knot. General term for securing a line to an object, another line, or itself. Also, unit of speed of one nautical mile per hour. Marlinespike. A pointed steel tool used in splicing to open the strands of a rope or cable. See Fid. Seize. To bind by many wrappings of small line. Seizing. Small stuff for binding. Splice. Joining lines by interweaving the strands. Whip. To bind the end of a rope with light line. 1 The lines aboard a sailboat are of such great importance that all sailors should know the types of cordage available and the various applications. They need to know where and how to use the lines on their boat. They also need the ability to tie various knots and hitches and to make splices. ors pride themselves in their knowledge and take pleasure in doing fancy work with the lines on their boats. Cordage 2 Many types of rope are available at a local marine supply store so selecting the best one for a particular need can be an interesting exercise. Discussions of cordage in the texts and manuals of a few years ago included reports on the relative merits of such natural fiber ropes as hemp, sisal, and manila. Today, synthetic materials are so much more suitable for use in the marine environment, in so many different ways, that the natural fiber ropes are seldom employed. Manila, for example, is the best of the natural fiber ropes but will rot if stored wet, is hard on hands, and is not as strong as synthetics. 3 Nylon was the first of the synthetic lines to receive widespread use. It has great strength and tremendous elasticity. This latter characteristic makes it useful for docking lines, towing bridles, and (especially) anchor rodes. Nylon stretches and absorbs shocks when the boat is anchored or tied up. Dacron is about 10% weaker than nylon but stretches much less. Dacron is preferred for sheets, halyards, and other lines where minimum stretch is desired. It has a similar appearance to nylon but is smoother. It is easier to chafe through, so care must be taken to lead the lines away from obstructions. 4 Polypropylene is a lightweight line that will float. It has only about half the strength of nylon and sometimes sheers off without warning when fatigued. It is more difficult to knot and splice because it is slippery. However, its floating characteristic makes it useful as a dinghy painter or mooring pick-up line. Lines that become wrapped around a propeller shaft are always a problem as well as dangerous, so polypropylene is the perfect answer. Use it for other low-load jobs where buoyancy is desirable.
2 Marlinespike Seamanship chest. Many sailors today still find pleasure in unusual functional and decorative rope work for their boats. 8 Even if the time isn t available to become proficient in the skill, a few basic knots, bends, and hitches should be learned. Only a few are required to serve nearly every common shipboard need, and they are easy to learn. The basic ones are included here along with descriptions of how to tie them, and some of the common uses for each. Figure 20 1 Three Strand Laid Line Laid vs. Braid 5 Laid lines, Figure 20 1, are fibers that are twisted into yarns, which are in turn twisted into strands. The strands, usually three, are then twisted around each other in a clockwise direction. The lay progresses towards the right so the lines are right-hand laid. Anchor rodes and dock lines are commonly laid nylon. Laid Dacron is also available and is often used for the rope tails on wire halyards. Figure 20 2 Braided Line 6 Lines are also braided, Figure Braid consists of a loosely laid core, which is then surrounded with a woven cover. Braided lines are more costly, but they have advantages. Their smooth outer surface distributes the load on the line among more fibers, thus reducing wear and allowing for longer rope life. Since their smooth outer surface makes the lines easy to handle, they are frequently used for sheets. Braided Dacron is also common as a halyard material when wire is not necessary. Knots Bends Hitches 7 ors on large sailing ships often spent their off watch time doing fancy work with cordage. Sometimes, it was for the ship, and other times, the fancy rope work was for the sailor perhaps a decorated ditty bag for his ropeworking tools or some beckets for his seaman s 9 The distinction between knots, bends, and hitches has become vague, but hitches connote a temporary fastening, usually to an object. A bend is a knot used to secure a rope to an object, or to tie two ends of a rope together. Knots are used to describe most fastenings, nautical or not. Frequently, bends and hitches are called knots. 10 There are several terms that make description easier. The standing part of a line is the main section, which is frequently attached to something or leads back to the coil. The bitter end is, as the name implies, the very end of the line. A bight (pronounced bite) is a U-shaped portion or loop in a line. Line and rope are not interchangeable terms, although they are often used that way. A line is a piece of rope that has been cut from a coil to be used aboard a boat. The same material is called rope while it is still part of the coil. 11 Overhand Knot. The overhand knot is the knot that most people learn to tie first, Figure It simply involves crossing the bitter end of a line over the standing part, and then taking the bitter end up through the loop that is formed. BITTER END Figure 20 3 Overhand Knot STANDING PART 12 This simple knot is part of several others and can be used as a stopper knot all by itself. A stopper knot is one that is tied in the end of a line to prevent the line from pulling back through a block or fairlead. When a sailboat is rigged, stopper knots are generally tied on the ends of the sheets to prevent them from unreeving and
3 20 Marlinespike Seamanship 159 Figure 20 4 Figure-8 knot becoming lost or snarled should the jib get temporarily out of control. An overhand knot used as a stopper can jam under a heavy load, becoming difficult to untie. 13 Figure-Eight Knot. If the bulk of an overhand knot is not adequate to prevent unreeving, several other stopper knots are in common use. The simplest is the figure-eight, Figure Square or Reef Knot. A knot that most people have heard of and many can tie is the square knot, or reef knot, so called because it is used on a sailboat to tie off excess sail material during reefing. the smaller line following exactly the path of the first turn. This bend is called a double sheet bend, Figure It is a bit less likely to shake out if the load is reduced. Working End Line 2 Standing Part Line 2 Figure 20 6 Double Sheet Bend Working End Line 1 Standing Part Line 1 18 Bowline. The bowline is a knot used for forming a loop in the end of a line, Figure It is a valuable knot to know, has many uses, is easy to tie, does not jam under heavy loads, and is easily cast off. Figure 20 5 Sheet Bend 15 Sheet Bend. The sheet bend, or common bend, is used for joining two lines together. The sheet bend, Figure 20 5, works well whether the lines to be joined are the same size or not. It is very easy to tie, is reliable under load, and unties easily. For these reasons, the sheet bend should be the knot that is used most often for joining two lines. 16 To tie the sheet bend, make a bight in the end of one of the lines. If the lines are of different sizes, the bight should be in the larger line. Pass the working end of the other line up through the bight, around under both legs of the bight, and then around over the legs of the bight, but under the standing part of the second line. To pull this knot snug, hold both legs of the bight together and pull on the standing part of the smaller line. 17 Double Sheet Bend. When tying this bend, many sailors will make a second round turn with the working end of Figure 20 7 Bowline 19 An important use for the bowline is to fasten jib sheets to the clew of the jib or genoa. 20 Clove Hitch. The clove hitch is the most common and versatile of the hitches, Figure It can be used to hang fenders from the lifelines or to tie the boat temporarily to a piling. Understand, however, that the clove hitch can work loose when there is not a constant pressure on both its ends. Therefore, it shouldn t be regarded as a permanent knot unless both ends are loaded. 21 The clove hitch is a jamming knot made like two halfhitches. The clove hitch is often used when making the anchor rode fast to a samson post. Tying a clove hitch for this purpose is quite simple. Turn a loop in the end of the anchor rode. Make this loop so that the end of
4 Marlinespike Seamanship 23 The rolling hitch can also be useful when it is necessary to take the load off a sheet or halyard temporarily, using a secondary line. If it is necessary, for example, to remove a loaded sheet from a winch, a line can be attached to the sheet above the winch using a rolling hitch. This hitch will not slide along the line on which it has been tied. The temporary line can then take the load while the sheet is transferred to another winch, or cleat. This is particularly helpful when you get an override on a winch that is, the sheet is jammed on the winch. Figure 20 8 Clove Hitch the rode passes under the standing part, then drop the loop over the samson post. Now, with the line beyond the samson post, make another loop in exactly the same manner. Drop the second loop over the first loop. Taking a strain on the bitter end will tighten the knot. 24 Anchor Bend or Fisherman s Bend. A number of different knots are called anchor bends. The most common anchor bend is also called the fisherman s bend. As the name implies, the anchor bend is used to secure the anchor rode to the anchor. For this purpose, it must be a non-slip knot that can be relied upon through successive loading and unloading while out of sight. Because of its non-slip properties, this knot can be quite useful aboard the sailboat in places other than the anchor rode. See Figure Rolling Hitch. The rolling hitch is a knot used when affixing a line to a smooth spar when the pull on the line is going to be along, or nearly along, the spar, Figure Enlarged View of Hitch Sheet Override of Line Winch 2 Line to Remove Tension Winch 1 Figure 20 9 Rolling Hitch Figure Anchor Bend 25 A knot is used to temporarily join lines. Splicing is also used to join lines, but has advantages aside from permanence. The line with a well-made splices is less bulky. Splices are also stronger than knots. A line with a good knot in which there are no tight kinks retains about
5 20 Marlinespike Seamanship % of its strength; a spliced line retains about 90% of its strength. 26 Splicing is easier to learn using three-strand natural fiber lines than three-strand synthetic lines. The synthetic lines are easily spliced, but it takes a bit more attention to ensure that the individual strands do not unravel during splicing. So start practicing with a fiber line such as manila or sisal. 27 If a small-diameter line is used, the only equipment needed is a sharp knife. When splicing a larger line, either a marlinespike or a fid will be required. A marlinespike is a pointed metal tool used to separate the strands of a line during the splicing process. A fid is a similar tool originally made of wood but now frequently made of wood and/or metal. Traditionally, the fid was used for fiber rope, while the marlinespike was used for wire rope. 28 The short splice is the strongest way to join two lines. Since it increases the diameter of the line at the splice, the short splice should not be used to join two lines that must pass through a block. If a spliced line is to pass through a block or over a sheave, use a long splice. A long splice increases the diameter of the line at the point of splice only slightly, but is not as strong as a short splice. 29 The eye splice is perhaps the easiest to learn. It forms a permanent loop in the end of a line in either threestrand or braid line. It is used almost universally aboard sailboats to attach fittings to sheets and halyards. 30 Braided line is commonly used aboard sailboats and has several advantages. It is strong, it is easy on the hands, and it presents a greater surface area to a winch (for increased friction) than does laid line. Splicing braided line is different from splicing laid line, but it is no more difficult. However, special fids will need to be obtained. The fids come in different sizes for varying line sizes and can be purchased individually or in sets, complete with instructions for their use. Whipping 31 Every sailor should know how to protect the ends of his lines from unlaying and forming unsightly cow s tails. Both natural and synthetic lines will unlay if left unprotected. Even braided lines, which do not unravel as laid line does, will eventually fray and require wasteful cutting of the ruined portion. 32 Synthetic lines can be temporarily protected by heating the ends and fusing the yarns together. This is frequently done using a match or cigarette lighter. A soldering iron or gun may also be used. Simply heat the newly-cut end of the line until the yarns melt and form a homogeneous melted layer. This layer will harden and protect the end from fraying. Be careful to keep your fingers away from the molten nylon or Dacron, since it will stick to your skin and burn painfully. Commercial dips are also available for this purpose. 33 This fusing process is quick and easy. However, if the line is to receive much use, the fused end will eventually break up and allow the line to fray. For this reason, synthetic lines as well as natural fiber lines should be whipped. 34 To make permanent whippings, a needle and twine will be required. A sail needle and a sailmaker s palm are helpful tools and should be standard on a sailboat. The sail needle is triangular; a sailmaker s palm is a leather strap with a pitted iron piece fitted in the palm. The iron piece is used to push the needle through heavy material or rope. 35 There are many different kinds of permanent whippings, some plain and some fancy. The basic permanent whipping will be discussed here. It is called the palm-andneedle whipping. To begin the whipping, put the twine through a strand or two using the sail needle. The bitter end of the twine should be short enough to be covered by the turns of the whipping, and should be laid along the line toward the bitter end of the rope the direction in which the whipping will be made. 36 Begin making tight turns around the rope with the whipping twine. When a distance approximately equal to the diameter of the rope has been whipped, pass the twine through a strand using the needle. Have the twine emerge from the line close to the top of the whipping between two strands, Figure Figure Whipping
6 Marlinespike Seamanship propeller. The best way to ensure a smooth running line is to have it properly coiled. Figure Completed Whipping 37 Now bind the whipping together with worming turns, Figure Take the twine down across the whipping above the crevice between two strands. Push the needle through the rope just under the whipping so that it emerges between two different strands at the top of the whipping. Now, pull the twine down across the whipping, again over the separation between two strands. Put the needle through the rope, again, so that it emerges between the two remaining strands at the top of the whipping. Pass the twine once again over the whipping, and push the needle, again, through the rope from bottom to top of the whipping. This time cut the twine close to where it emerges from the rope. The whipping is now complete. 38 If a sailmaker s needle and palm are not available, the end of any line can be protected with temporary whipping. Waxed, natural-fiber whipping twine has been used for whipping natural-fiber ropes. However, the small-diameter whipping twine is in danger of rotting after the wax has worn off, so many sailors today use Dacron sailmaker s twine for all whipping. Waxing the twine with beeswax makes it easier to maintain tension on the whipping as it is applied. Heaving A Line 39 It is important to be able to heave a line a fair distance. Getting a line to a dock quickly makes docking easier, and passing a line to a vessel in distress can be most safely done from a distance. Knowing how to heave a line can be invaluable. 40 While any line can be heaved farther using the proper technique, having a proper heaving line aboard a boat can substantially increase the distance reached with the line. A heaving line is usually small in diameter and has a monkey fist tied in the end of it. The monkey fist usually contains a lump of lead or some other small heavy object. This knot and weight make the line much easier to heave. 41 The next requirement is to have the heaving line properly coiled. Some sailors will stream the line behind the boat to remove the kinks from the line. This can have disastrous effects if the line happens to wrap around the 42 The best way to coil a laid line is to place an end in the left hand with the line to be coiled leading away from you. Then with the right hand, make clockwise loops about 2 feet / 60 centimeters long. If the line is to be stowed, leave about 2 feet and finish by making several round turns around the middle of the coil. Form a bight with the remainder, and push the bight (but not the end) through the top eye in the coil. Then pull the bight back over the top of the coil, and pull the end to tighten. 43 A laid line will kink if it is not compensated for the strand twist. The kinks can be avoided by giving the line a slight clockwise twist when forming the loops. Braided line has no built-in strand twist so no twist is necessary. A braided line can be stowed by faking. Grasp the line near where it is secured, perhaps on a cleat, with your left hand palm up and your thumb pointing toward the cleat. With your right hand, thumb pointing the same direction, grasp the line a comfortable distance down the line. Bring your right hand past your left and drop the line into your left hand as your right hand moves back to grasp the next loop. In most cases the line will fall into a figure eight pattern. When this line is thrown, it will have no kinks. 44 Before heaving a line, secure the end to some part of the boat such as a cleat. This way, you can concentrate on the throw without having to worry about holding the end. Get the heaving line ready for throwing by carefully coiling it into coils about 18 inches / 45 centimeters in diameter. Split the coiled line into two sets of coils, holding the coils nearest the working, or weighted, end in your throwing hand. Hold the remainder of the coils in your other hand. This will leave a strand of line several feet long connecting the coils between your hands. 45 If your line has a weighted end, allow this weighted knot to hang about a foot below your throwing hand. Warn people in the target area to watch out for the line. A weighted monkey fist can be a dangerous projectile. To throw the line, swing both arms back toward your throwing side and heave the line with a side arm motion, like throwing a discus. As the line is released with the throwing hand, pitch the coils in the other hand in the same direction. If the line has been coiled properly and released at the right instant, it will reach its full length while still in flight.
7 20 Marlinespike Seamanship If a proper heaving line is not aboard, there are several knots whose sheer bulk will make the line easier to throw. The heaving line knot, which is simply a noose with the loop pulled way up short, is probably the best. Summary 47 Every sailor should know the types of cordage available, the various applications, and have the ability to tie various knots and hitches. Nylon is a very versatile synthetic material with great strength and elasticity, properties which make it an excellent material for use as anchor rodes. When joining two lines together, the sheet bend is the knot that should be used. When forming a loop in the end of a line such as is required for fastening jib sheets to the clew of the jib, the knot to use is the bowline. Splicing lines together enables 90% of the line s strength to be retained as compared to the best of knots under ideal conditions, which only retains about 80% of its strength. Both synthetic and natural fiber lines should be whipped to prevent the ends from unlaying.
8 Marlinespike Seamanship
9 20 Marlinespike Seamanship 165 Homework: Section 20: Marlinespike Seamanship 1. The best type of line to use for docking and anchoring is: a) nylon. b) manila. c) Dacron. d) polypropylene. 2. What type of line is used for halyards and sheets? a) Manila. b) Nylon braid. c) Dacron braid. d) Polypropylene. 3. A good stopper knot is the: a) sheet bend. b) sheepshank. c) square knot. d) figure-eight knot. 4. A bend is used to: a) coil a line. b) form an eye splice. c) join two lines together. d) prepare a line for splicing. Name 5. A laid line has parted and must be rejoined to pass through a block. Which splice would you use? a) Eye splice. b) Long splice. c) Back splice. d) Short splice. 6. The two characteristics of polypropylene rope that make it dangerous are that it: a) stretches and floats. b) floats and is slippery. c) floats and sheers without warning. d) is slippery and sheers without warning. 7. Laid nylon line is commonly used for: a) vangs. b) sheets. c) halyards. d) anchoring and mooring. 8. The hitch used to fasten to pilings, railings, and to hang fenders is the: a) bowline. b) clove hitch. c) square knot. d) rolling hitch.
10 Marlinespike Seamanship 9. The proper fastening of a line to a spar for a pull along the spar is the: a) bowline. b) clove hitch. c) rolling hitch. d) anchor bend. 10. The proper fastening for a jib sheet to the clew is the: a) bowline. b) square knot. c) anchor bend. d) rolling hitch. 11. A short splice should not be used: a) with Dacron. b) when using synthetic line. c) when joining two pieces of line. d) when the splice must run through blocks. 12. Splicing laid line: a) is more difficult than splicing braided line. b) should only be attempted by an expert. c) decreases line strength more than a knot. d) can be learned easily and may be used to make an eye splice in a line. 13. Braided line is commonly used on sailboats because it: a) resists stretching. b) floats and holds well to cleats. c) is strong and easy on the hands. d) resists mildew, stretching, and can be washed. 14. A splice in a line typically retains: a) 90% of its strength. b) 75% of its strength. c) 60% of its strength. d) 50% of its strength.
KNOTS. A very short guide to knotting terminology used on these pages.
KNOTS A very short guide to knotting terminology used on these pages. This is not an exhaustive list of knotting terms; it just contains some of the more unfamiliar words that we have used. If you wish
More informationKnots, Hitches and Bends
Knots, Hitches and Bends It is hard to define clearly the terms knot, hitch and bend because their functions overlap. However, the terms may be generally defined as follows: Knots Hitches Bends Knots are
More informationTroop 226. Knot Master Program
Troop 226 Knot Master Program Knots are a skill taught at every level of scouting. The Knot Master program is designed to provide each scout an opportunity to learn essential knots. In addition to learning
More informationSea Scout Knots Knots Hitches Splices and Whippings
Sea Scout Knots Knots Hitches Splices and Whippings Knots www.artworkbygerry.com Bowline... 2 Bowline on the bight... 3 Clove hitch... 4 Double sheet bend... 5 Figure of eight... 6 Fireman s chair knot...
More informationScout It Out would like to extend its gratitude to all the sites where the following information had been gathered.
Rope Work introduces the basic knots that all Scouts and Guides should know. Most of the knots featured here are very useful in Pioneering and should be learnt. This Section does not fully teach the exact
More informationKnots /2017. Camp and Outdoor Curriculum Manual
Knots 05-4487-01/2017 Camp and Outdoor Curriculum Manual Parts of a Rope Bight: A bend in the rope Loop: Crossing the rope over itself, creating a loop Overhand Loop: When the working end of the rope crosses
More informationKnot Masters Program
The Knot Masters program helps Scouts to learn the knots they need for advancement, Scouters to become proficient in knot tying, and keeps knot tying skills sharp. Scouts and Scouters are encouraged to
More informationSeamanship. A braided line comprises a core of braided or stranded threads covered with a sheath. The center or core of the line gives strength.
Seamanship 1. Describe the life boat ropes. On a life boat, we rarely use the word rope but rather lines to describe all of the ropes. Moreover, each line has a specific name, such as the painter, halyard
More informationMSC-132: Introduction, Plain Whipping, Loops, Turns & Hitches
MSC-132: Introduction, Plain Whipping, Loops, Turns & Hitches This presentation is designed to be used as a study companion to lectures, labs and handouts given in Fishing Gear Technology I. Advance each
More informationTying Farm Knots. Working with Heifers
Tying Farm Knots A rope is one of the most common of tools used to restrain animals. Unfortunately, most people never learn which knots are most efficient to use in given situations. Practice tying the
More informationChapter VIII. Rigging. Rope and its uses. Rope of any kind can be described as belonging to one of two main types:
Chapter VIII Rigging Rope and its uses Rope of any kind can be described as belonging to one of two main types: Cordage (which is made of vegetable or synthetic fibres). Steel wire rope, or stainless steel
More informationLevel Two Green Rope. Clove Hitch
Level Two Green Rope Level Two consists of a combination of two knots (or hitches), all five lashings and the three basic splices. The lashings are essential for pioneering activities and to create camp
More informationROYAL CANADIAN SEA CADETS PHASE ONE INSTRUCTIONAL GUIDE SECTION 1 EO M TIE KNOTS, BENDS AND HITCHES PREPARATION
ROYAL CANADIAN SEA CADETS PHASE ONE INSTRUCTIONAL GUIDE SECTION 1 EO M121.01 TIE KNOTS, BENDS AND HITCHES Total Time: 120 min PREPARATION PRE-LESSON INSTRUCTIONS Resources needed for the delivery of this
More informationInformation Booklet 3
TAKING. IT FURTHER Create lessons to demonstrate and learn how to tie the following knots: Timber hitch Highwayman s hitch Sheepshank Bowline Sheet bend Groups could then build knot boards showing how
More informationPioneering. It s More Than Just Knots and Rope
Pioneering It s More Than Just Knots and Rope Mark Montrose Retired Scoutmaster Troop 14, Santa Clara Venture Crew Advisor Crew 14, Santa Clara Assistant District Commissioner Pioneer District University
More informationPioneering. It s More Than Just Knots and Rope
Pioneering It s More Than Just Knots and Rope Mark Montrose Retired Scoutmaster Troop 14, Santa Clara Venture Crew Advisor Crew 14, Santa Clara Assistant District Commissioner Pioneer District University
More informationKnots. Some points on ropes:
Knots Knots have been created so that they may perform a certain job effectively. A good knot is easy to tie and just as easy to untie, does not slip under strain and can be relied upon. There are only
More informationEnd. Standing Part. An underhand loop is made by crossing the end under the standing part.
Knot Board Learn to tie the four basic camping knots as illustrated as well as others you might add. Practice them until you can tie them well. Display them on a knot board made from a square of peg board
More informationLOOP KNOTS: A loop knot, like a hitch, fastens a rope to another object. A loop knot may be tied in the hand and then placed over the object, while a
LOOP KNOTS: A loop knot, like a hitch, fastens a rope to another object. A loop knot may be tied in the hand and then placed over the object, while a hitch is tied directly to the object. However, since
More informationSince rope is a vital part of a boat's equipment, a good sailor should be familiar with how to handle rope and how to tie a few basic knots.
SCOUTS Creating a Better World The Scout Association of Nigeria L'Association des Scouts du Nigeria La Asociación de Scouts de Nigeria A Associação dos Escoteiros de Nigéria جمعیة كشافة نیجیریا National
More informationRopework. Stopper Knots. Overhand Knot ROPEWORK. Figure of Eight 3.
Ropework 157 Ropework Stopper Knots Stopper knots are used as a temporary method of stopping a rope from fraying or as a method of locking other knots which may be prone to loosening. These knots are:
More informationStart by crossing the two sticks or dowels at perpendicular or 90 degree angles.
Square Lashing Used to fasten two spars or poles together. Start by crossing the two sticks or dowels at perpendicular or 90 degree angles. Make a Clove Hitch on the vertical stick or dowel near the point
More informationRopework. Stopper knots. Overhand Knot ROPEWORK. Figure of Eight 3.
Ropework 1 Ropework Stopper knots Stopper knots are used as a temporary method of stopping a rope from fraying or as a method of locking other knots which maybe prone to lossening. The knots are the Overhand
More informationRopes and Rope Work. Agriculture Mechanics Santa Ynez High School
Ropes and Rope Work Agriculture Mechanics Santa Ynez High School 5 Common Uses of Rope 1. Ropes are used to secure livestock and pets through the use of halters, lead ropes and leashes. 2. Heavy loads,
More information2018 Osprey Yacht Club
Page 1 2018 Osprey Yacht Club Optimist Sailboat Youth Training Manual Or How to have a lot of fun on a small sailboat! Revision Date: August 19, 2017 Page 2 Table of Contents Table of Contents... 2 What
More informationROPE USE TABLE. Extension Bulletin 192 Reprinted June 1945
RODEWOR K Extension Bulletin 192 Reprinted June 1945 ROPE USE TABLE Use Knot or Splice Page Anchor knot... Fishermen's bend... 17 Bag tie... Miller's tie... 15 Boat tie... Clove hitch No. 1 or 2... 16
More informationSemper Salus! CERT Disclaimer 3/4/2014. Lamorinda Community Emergency Response Team. Safety is Always the Number One Priority!
Lamorinda Community Emergency Response Team Rescue Ropes, Anchors and Knots Semper Salus! Safety is Always the Number One Priority! CERT Disclaimer This 2 hour presentation will NOT qualify you to perform
More informationSECTION V. Terminology: Bight: Double Bight: Loop: Turn: Round Turn: Half Hitch: Girth Hitch: Running End: Standing End:
SECTION V. Terminology: When using ropes, understanding basic terminology is important. The terms explained in this section are the most commonly used in military mountaineering. (a) Bight: A bight of
More informationKnot Tying for Scouts and Scouters
Knot Tying for Scouts and Scouters Gary Panczner KNOT TYING Table of contents; Parts of a rope...3 Properties of rope fibers...4 Whipping...5 Overhand knot...5 Figure eight knot...5 Fisherman s knot...6
More informationCaving Knots. Prepared by CCPO S C Milton CSCA Technical Training Adviser
Nov 2001 Prepared by CCPO S C Milton CSCA Technical Training Adviser INTRODUCTION 1. This booklet provides information about knots used for caving. The "Basic knots" detailed within this booklet are taught
More informationKnots & Their Uses. there are different knots for different purposes and all knots are not good for all purposes practice makes perfect
Knots & Their Uses a good knot holds but is easy to open if necessary there are different knots for different purposes and all knots are not good for all purposes practice makes perfect a good knot needs
More informationKnots for Cavers Knots, Hitches, Bends, and Splices Step By Step Instructions For tying knots for Caving
Knots for Cavers Knots, Hitches, Bends, and Splices Step By Step Instructions For tying knots for Caving Knot Requirements by Slide Edge Color Required Knots Additional Knots Credits The photography and
More informationSplicing Instructions. Standard Double Braid Eye Splice Type 1 Double Braid Ropes
Splicing Instructions Standard Double Braid Eye Splice Type 1 Double Braid Ropes Introduction Double Braid Eye Splice This document describes the steps required to perform a Double Braid Eye Splice in
More informationParts of a Rope 1. Carrick Bend 2 Fisherman s Bend 4 Hunter s/rigger s Bend 5 Sheet Bend 7
- 1 - Contents Parts of a Rope 1 Bends Carrick Bend 2 Fisherman s Bend 4 Hunter s/rigger s Bend 5 Sheet Bend 7 Hitches Clove Hitch 8 Highwayman s Hitch 9 Italian Hitch 11 Marline Hitch 12 Round Turn and
More informationList of knot terminology From Wikipedia, the free encyclopedia
Page 1 of 7 List of knot terminology From Wikipedia, the free encyclopedia This page explains commonly used terms related to knots. Contents : A B C D E F G H I J K L M N O P Q R S T U V W X Y Z B Bend
More informationKnot Basics. A knot is a bond formed by tying a rope to itself, to another rope, or to an object. Gonna get you! Contents
Knot Basics A knot is a bond formed by tying a rope to itself, to another rope, or to an object. Will Durness Knots are used by nearly everyone (e.g., tying shoes) and in special situations by many groups
More informationSeamanship 2. Contents. The technical skills covered by the practical seamanship module are essential for ensuring safety and efficiency at sea
Seamanship 2 Contents Overview... 2 1. Rope Types... 2 1.1 Laid Ropes... 2 1.1 Braided Ropes... 2 2. Rope Properties... 3 3. Rope Usage... 4 3.1 Mooring Lines... 4 3.2 Towing Rope... 4 3.3 Anchor Rope...
More informationKNOTS. By Oliver Cameron with Ole Wik
KNOTS By Oliver Cameron with Ole Wik What knots do you use most often? 1 I think this is all superfluous, in that there is so much material well written and illustrated about using ropes and tying knots.
More informationrequirement 9 Polyester Nylon
Page 4, requirement 9: By yourself, build an A-trestle OR X-trestle OR H- trestle using square and diagonal lashings. Explain the application of the trestle you build. Demonstrate how to tie two spars
More information3 KNOTS 3.1 INTRODUCTION
3 KNOTS 3.1 INTRODUCTION Termination knots enable a termination to be made at any point along the rope s length. Most create loops, which are then used to attach the rope to anchors. Exceptions are: firstly,
More informationObjectives (1 of 3) List at least two types of materials and designs used in rope manufacture. Define and describe the following: Dynamic rope Static
Chapter 16 Rescue Objectives (1 of 3) List at least two types of materials and designs used in rope manufacture. Define and describe the following: Dynamic rope Static rope Webbing List at least five rules
More informationknot_craft.doc 1 of 16 Last Updated 2-Sep-08
Knot Craft HOW CORD ADVANCEMENT WORKS... 2 PURPLE AND BLACK CORDS (TENDERFOOT LEVEL KNOTS)... 3 Square (Reef) Knot... 3 Two Half Hitches... 3 Taut Line Hitch... 4 Whipping... 4 YELLOW AND GREEN CORDS (INTERMEDIATE
More informationESCONDIDO FIRE DEPT TRAINING MANUAL Section Truck Module Page 1 of 8 Ropes - Knots Revised
Truck Module Page 1 of 8 SERVICE KNOTS Common Knot Tying Terms Working End- the working end of a rope is the part used in forming a knot. (also known as the loose end or bitter end) Running End- the running
More informationOver Deck Control Lines V1
Over Deck Control Lines V1 1 - Pack Contents Downhaul control line Outhaul control line Downhaul takeup elastic 3 x 30mm block Traveller line (with pre-spliced loop) 2 x Side deck strops 2 x Ronstan Shocks
More informationALAMAR KNOT. [Sterp 2] [Step 1] Double the strand as shown. [Sterp3]
ALAMAR KNOT The alamar knot is a decorative knot related to the pretzel. The pretzel knot is tied in a single strand; the alamar knot is tied by doubling the strands as showwn in [Step 1] [Step 1] Double
More informationSquare Diagonal Tripod Japanese Square Filipino Diagonal Round Shear Ladder
Square Diagonal Tripod Japanese Square Filipino Diagonal Round Shear Ladder Square Lashing - Step by Step Used to fasten two spars or poles together. Start by crossing the two sticks or dowels at perpendicular
More informationKnot Tying Honour Booklet
Knot Tying Honour Booklet Name: Church: Club: Class Due Date: In order to successfully complete this honour, you must: 1. Satisfactorily complete this Booklet. The pass mark is 75%. The number of marks
More informationTRAINING BULLETIN ROPE 5 March 8, 2007 KNOTS AND HITCHES NOMENCLATURE
TRAINING BULLETIN ROPE March 8, 007 NOMENCLATURE Hitch A temporary method of securing an object, fastened so that it can be readily undone, i.e., Half Hitch. Bend The tying of the ends of two ropes to
More informationDouble Braid Class II Eye Splice for TS-II Turbo
SAMSON SPLICING INSTRUCTIONS Double Braid Class II Eye Splice for TS-II Turbo 1 MEASURING AND MARKING The measurements are the same as those for the direct bury eye splice for Class II ropes. Measure 3
More informationDeckhand Crew. Deckhand Crew Responsibilities
Deckhand Crew Responsibilities Deckhand Crew Deckhands must be thorough seamen, for they are responsible for many types of tasks. Deckhands, along with the Bosuns, are in charge of most tasks done "on
More informationDeckhand Duties Questions
Deckhand Duties Questions Ropework - Deck Gear - Moor and anchor -Lookout -Maintenance - Hygiene/safety Ropework A monkey fist is the terminal to a heaving line. Question 2 (1 Mark) Seawater acts as a
More informationROYAL CANADIAN AIR CADETS PROFICIENCY LEVEL FOUR INSTRUCTIONAL GUIDE SECTION 3 EO M TIE KNOTS AND LASHINGS PREPARATION
ROYAL CANADIAN AIR CADETS PROFICIENCY LEVEL FOUR INSTRUCTIONAL GUIDE SECTION 3 EO M490.03 TIE KNOTS AND LASHINGS Total Time: 60 min PREPARATION PRE-LESSON INSTRUCTIONS Resources needed for the delivery
More informationWoodsman s Thong Manual. Patriots Path Council, B.S.A. Rope, Knots & Pioneering. Compiled by: Angelo Greco
Woodsman s Thong Manual Patriots Path Council, B.S.A. Rope, Knots & Pioneering Compiled by: Angelo Greco Rope History of Rope and Knots: The first rope was probably fashioned of vines or reeds. Man then
More informationRoles: Presentation Questions:
DECKHAND CREW Instructions: (mates read aloud) This crew packet contains important information for you to know aboard the Balclutha, and it will help you complete your project. First, read the part about
More informationKnots and Hitches. To make a reef knot: Check out this video:
Knots and Hitches Being able to work with rope efficiently and effectively is an essential camp skill. Introduce your girls to the following knots, hitches and lashings before going to camp, and have them
More informationOPERATIONAL CHECK LIST
www.spinnakersailing.com (650) 363-1390 OPERATIONAL CHECK LIST https://twitter.com/#!/spinnakersailin http://www.facebook.com/spinnakersailingrwc http://www.spinnakersailing.com/newsletter.html Dear Sailor,
More informationArmy Mountain Warfare School Ethan Allen Firing Range Jericho, VT Military Mountaineer Course Knot Guide
Army Mountain Warfare School Ethan Allen Firing Range Jericho, VT 05465-9796 Military Mountaineer Course Knot Guide 2 - Basic Knot Tying 071E9002 INTRODUCTION: There are many knots used in mountaineering.
More informationRESCUE TECHNICIAN KNOT GUIDE
RESCUE TECHNICIAN KNOT GUIDE RESCUE TECHNICIAN - BASIC September 20, 2014 8AM-5PM - Location T.B.A September 27, 2014 8AM-5PM - Location T.B.A October 11, 2014 8AM-5PM - Location T.B.A This Class is an
More informationThe importance of splicing especially for braids made with UHMWPE fibre
The importance of splicing especially for braids made with UHMWPE fibre Nautilus has installed a high spec strength tester for testing ropes up to 14tonnes. There has been much knowledge gained as we can
More informationDear Friend, P.S: Remember, sharing is caring, so please also share this information with any friend, family or acquaintance you think could benefit!
Dear Friend, A good knot can save lives when you're dealing with a survival situation, performing first aid, setting traps and snares, fishing lines, climbing and much more. However, you ll first need
More informationFISH NET REPAIR. By Alfred Carlson
FISH NET REPAIR By Alfred Carlson 2 Contents 1. Contents 2 2. 3-Spot Repair (One Broken mesh) 3 3. V-Shaped Repair (Two Broken meshes ) 23 4. N-Shaped Repair (Three Broken meshes) 33 5. M-Shaped Repair
More information04 Practical Seamanship. Captain
04 Practical Seamanship Exhibit elements of basic seamanship RQ RQ Describe Characteristics, construction, advantages and disadvantages of various types of rope Describe the Factors that Affect the Strength
More informationRopework & Securing Loads
Ropework & Securing Loads Name Description: In this exercise the student will learn to work with rope by tying common knots. Students will demonstrate securing loads with common binders and rope. Materials:
More informationNational Maritime Center
National Maritime Center Providing Credentials to Mariners (Sample Examination) Page 1 of 7 Choose the best answer to the following Multiple Choice Questions. 1. On a small boat, which knot is best suited
More informationTHE AMERICAN BARN DOOR KITE
THE AMERICAN BARN DOOR KITE Oregon Kitemaker s Retreat January 2007 Rod Beamguard 4104 NW 112 th Way Vancouver, WA 98685-3578 (360) 574-8050 home (360) 750-9833 office kytfevr@wa-net.com PLANFORM BARN
More informationThe Forest School Training Co. OCN accredited training
Useful Knots for Forest School The Overhand Knot 1. Cast an overhand loop. Take the working end and push it through the loop. The Figure of Eight Knot 1. Form a loop and pass the end under the standing
More informationLab # 3 -- Ropework. In this exercise the student will learn to work with rope by making a rope halter, splicing the rope, and tying common knots.
Description: Lab # 3 -- Ropework Name In this exercise the student will learn to work with rope by making a rope halter, splicing the rope, and tying common knots. Materials: 15' -- 1/2 polypropylene rope
More informationGENERAL GUIDELINES FOR PROPER RIGGING PRACTICES AND INSPECTION & REMOVAL CRITERIA FOR SLINGS PER OSHA
GENERAL GUIDELINES FOR PROPER RIGGING PRACTICES AND INSPECTION & REMOVAL CRITERIA FOR SLINGS PER OSHA 1910.184 SAFE OPERATING PRACTICES -.Whenever any sling is used, the following practices shall be observed:
More informationENABLING OBJECTIVE AND TEACHING POINTS. BUSHCRAFT: TIME Two 30 minute periods. 6. METHOD/APPROACH: a. demonstration; and. b. performance.
CHAPTER 4: LESSON SPECIFICATIONS COURSE TITLE: RED STAR COURSE ENABLING OBJECTIVE AND TEACHING POINTS CTS NUMBER: A-CR-CCP-116/PC-001 TRAINING DETAILS BUSHCRAFT: 403.16 5. TIME Two 30 minute periods. 1.
More informationBasic Rigging Knots. Clove hitch: primarily used to secure branches which are being rigged. To secure this hitch from rolling
Clove hitch: primarily used to secure branches which are being rigged. To secure this hitch from rolling out under load during rigging, it is vital to secure the tail end of the rope around the standing
More informationSAIL WELL, STAY WELL. Sydney Flying Squadron ACN Sydney Flying Squadron. SAILING A SKIFF a guide
Historic 18 foot Myra Too Sydney Flying Squadron ACN 000 487 230 76 McDougall Street Milsons Point. 2061 SAIL WELL, STAY WELL SAILING A SKIFF a guide PO Box 577 Milsons Point 2061 T: 9955 8350 Web: sydneyflyingsquadron.com.au
More informationSplicing Instructions. Moran Tuck Splice
Splicing Instructions Moran 5-4-3 Tuck Splice Introduction Moran 5-4-3 Tuck Splice This document describes the steps required to perform a Moran 5-4-3 Tuck Splice. The Moran 5-4-3 Tuck Splice is a Cortlandapproved
More informationINDEX
INDEX Using New Fly & Hook Threader... 1 Clinch Knot...2 Triline Knot...3 Blood Knot (Clinch Style)...4 End Loop/Dropper Loop...6 J.R. Loop Knot (For more bait action)...7 Shank Tie/Snelled Hooks...9 #6
More informationBasic fly fishing knots Compiled by the guys in Cabela s richfield wisconsin fly shop
Page 24 Loop to loop connection The preferred & probably the best method of attaching a leader to the built-in loop on a fly line, avoiding wear and tear on the vinyl coated fly line loop. A loop to loop
More informationROYAL CANADIAN SEA CADETS PHASE ONE INSTRUCTIONAL GUIDE SECTION 1 EO M TIE KNOTS, BENDS AND HITCHES PREPARATION
ROYAL CANADIAN SEA CADETS PHASE ONE INSTRUCTIONAL GUIDE SECTION 1 EO M121.01 TIE KNOTS, BENDS AND HITCHES Total Time: 120 min PREPARATION PRE-LESSON INSTRUCTIONS Resources needed for the delivery of this
More informationSlow-Pull Testing Of The "Double Overhand On Itself" Tie.
Slow-Pull Testing Of The "Double Overhand On Itself" Tie. by Collin O'Neill Introduction Over the past few years of my caving experience I have witnessed several cavers using an unconventional knot on
More informationKNOTS. Overhand Knot. Page 12 of 32
Overhand Knot KNOTS The overhand knot is useful for tying cord around a pin to end a macramé project, holding beads in place, and tying your shoes! It also makes a nice variety knot in a macramé design.
More informationNational Maritime Center
National Maritime Center Providing Credentials to Mariners (Sample Examination) Page 1 of 7 Choose the best answer to the following Multiple Choice Questions. 1. Which is usually the most gentle way of
More informationBowline. Bowline on a bight
Bowline The Bowline holds tight during extreme situations, yet unties with minimal effort. Used mostly in rigging situations this quickly tied and untied knot is perhaps our most important tool! Caution!
More informationHow to Make a ROPE HALTER. Easy steps to create your own knotted rope halter for your horse. From The American Quarter Horse Journal library
How to Make a ROPE HALTER Easy steps to create your own knotted rope halter for your horse. From The American Quarter Horse Journal library www.americashorsedaily.com 1 www.americashorsedaily.com Tie One
More informationInstallation and Operating Instructions for Automotive Winch Synthetic Rope
Installation and Operating Instructions for Automotive Winch Synthetic Rope 2 1 Synthetic Rope Kit Parts List Part No. 251262 1. Rope Assembly (3/8 x 100 ) 2. Hook Strap WARNING: A minimum of EIGHT wraps
More informationA Primer on Knots, Hitches, and Bends 1
A Primer on Knots, Hitches, and Bends 1 The term knot is used generically to cover knots, hitches, and bends. It was done so here. Technically, knots, hitches and bends are structurally different and serve
More informationWhat Knot to Use in a Primitive Situation
What Knot to Use in a Primitive Situation by Bill Scherer It's been my observation that every practicing abo should have several knots memorized, ready to be used anytime. If you are making primitive cordage,
More informationHow to Make a Rope Halter
How to Make a Rope Halter ebooks Rope halters are a time-honored tradition for many horsemen. Practical and inexpensive, rope halters are perfect for throwing in the truck for emergencies or keeping under
More informationRigging guide for the Swift Solo Volume 1 (mostly boat rigging)
Rigging guide for the Swift Solo Volume 1 (mostly boat rigging) Thanks to Greg Ryan for the drawing 5/28/2004 1 Index Page 3 Preface and Safety 4 Quick line measurements you ll need 5 Spinnaker pole launcher
More informationScout. Knot Master. Guide
Scout Knot Master Guide Acknowledgment: Special thanks to Troop 944, Rockville, MD for allowing us to adapt, modify and use this guide for our troop. BSA Troop 610 Thiếu Đoàn Lam Sơn, San Jose, CA Knot
More informationMAKING A SIMPLE FLEMISH TWIST BOWSTRING #1 by Kirby
MAKING A SIMPLE FLEMISH TWIST BOWSTRING #1 by Kirby Here is a tutorial on making a flemish bowstring. I don't own a jig so I use my workbench. I put two nails in the bench as pegs, 6 to 8 inches longer
More informationScout Meeting Schedule: Week 1 Theme: Pioneering A Date:
Scout Meeting Schedule: Week 1 Theme: Pioneering A Date: Time Activity Program Details Leader Responsible 15 mins. Gathering Activity Bowling for Bottles 10 mins. Opening Ceremony Details can be found
More informationCourse Code: 5114 Tied Up In Knots
Course Code: 5114 Tied Up In Knots Mt. Diablo-Silverado Council Leader Education & Discovery Conference January 30, 2016 Instructor: Bruce F. Lezer, Pack 262 1 Introductions Please share the following:
More informationHow to tie a sling for SHE's prototype HotPot
How to tie a sling for SHE's prototype HotPot David Delaney, Ottawa, ddelaney@sympatico.ca May 7, 2003 Solar Household Energy, Inc. (SHE) is developing the HotPot, an excellent greenhouse pot for solar
More informationFar East Boat Optimist Rigging Instructions
Far East Boat Optimist Rigging Instructions These instructions are written specifically for Far East Boats Championship and Racing Optimist. Parts of the Optimist PAGE 1 Sprit Wind Indicator Sail Mast
More informationSerenity Houseboat. Standard Operating Procedures for:
Serenity Houseboat Standard Operating Procedures for: Docking I. Safety a. Never get between the houseboat and the dock or other larger object. b. Always wear PFDs during docking. c. Always wear snug fitting,
More informationYou may order this publication from WCB Publications and Videos, Please quote ordering number BK60.
The following material is the property of the Workers Compensation Board of British Columbia and may not be reproduced by those outside of B.C. For those within British Columbia, this material may only
More informationNOTES: Information Booklet 3. Basic Pioneering. Compiled For Cambridgeshire Scouts September2013
NOTES: Information Booklet 3 Basic Pioneering 12 Compiled For Cambridgeshire Scouts September2013 Basic Pioneering It is important that you read this before attempting any Pioneering Project. Pioneering
More informationProof load is the load applied in performance of a proof test. Proof test is a nondestructive tension test performed by the sling manufacturer or an
1910.184 Slings (a) Scope. This section applies to slings used in conjunction with other material handling equipment for the movement of material by hoisting, in employments covered by this part. The types
More informationLevel Three Blue Rope
Level Three Blue Rope Level Three consists of a combination of six fishing knots that work well in monofilament fishing line, two climbing knots and two knots used to secure heavy loads. Monofilament fishing
More informationDolly wheels in slot #8 for Boat #10.
Rigging: Laser SAIL SELECTION: The International Laser Class has three different official rigs. Each sail is designed for sailors of different weights. The Standard Rig was designed for sailors weighing
More informationROYAL CANADIAN SEA CADETS PHASE TWO INSTRUCTIONAL GUIDE SECTION 1 EO M USE A STROP FOR SLINGING PREPARATION
ROYAL CANADIAN SEA CADETS PHASE TWO INSTRUCTIONAL GUIDE SECTION 1 EO M221.01 USE A STROP FOR SLINGING Total Time: 90 min PREPARATION PRE-LESSON INSTRUCTIONS Resources needed for the delivery of this lesson
More informationInstruction Manual. Read This Manual Carefully!
357634-Lifesling2Manual_v2.qxd 2/21/03 11:10 AM Page 1 Instruction Manual Important! Read this manual before installing the Lifesling2; practical knowledge of the system s use is essential before an emergency
More informationknots for rope ends or for grips on thin rope
knots & lashings The ability to join two pieces of natural material together, and so increase their length, gives man the ability to make full use of many natural materials found locally. Sailors probably
More information