ULTIMATE 12 RUDDER INSTALLATION INSTRUCTIONS
|
|
- Bernadette George
- 6 years ago
- Views:
Transcription
1 ULTIMATE 12 RUDDER INSTALLATION INSTRUCTIONS TOOLS NEEDED: DRILL ¼ DRILL BIT ¾ HOLE SAW 3/16 DRILL BIT PHILLIPS HEAD SCREWDRIVER 7/16 WRENCH HEAT SOURCE: PROPANE TORCH, LIGHTER OR HOT AIR GUN WIRE CUTTER CRIMPERS RIVET GUN 1. REMOVE THE SEAT AND FOOT PEGS. 2. REMOVE THE STERN FLOATATION FOAM. 3. CUT THE STERN GRAB HANDLE ROPE AND REMOVE FROM THE BOAT AND THE HANDLE. 4. USING A 3/16 DRILL BIT, CAREFULLY DRILL OUT THE 5 TH RIVET IN THE ADAPT A TRAC ON BOTH SIDES, COUNTING FROM THE STERN FORWARD. 5. USING A 3/16 DRILL BIT, CAREFULLY DRILL OUT THE 4 TH RIVET IN THE ADAPT A TRAC ON THE STARBOARD SIDE, COUNTING FROM THE STERN FORWARD. 6. USING A ¼ DRILL BIT, DRILL TWO HOLES IN THE STERN OF THE BOAT JUST ABOVE THE PARTING LINE FOR THE RUDDER UPHAUL LINES.
2 7. DRILL A ¼ HOLE ON THE PORT SIDE DECK, 3 FROM THE STERN. THEN DRILL ANOTHER 1/4 HOLE 1 FROM THE FIRST HOLE FOR THE RELOCATED GRAB HANDLE. 8. DRILL A ¼ HOLE 9 ½ FROM THE STERN FOR THE RUDDER HOLD DOWN BUNGEE. 9. PUSH THE BUNGEE DOWN THROUGH THE DECK OF THE BOAT. TIE A KNOT AT THE END OF THE BUNGEE.
3 10. USE A ¾ HOLE SAW TO DRILL THE HOLE FOR THE RUDDER UPHAUL LINES TO EXIT THE INSIDE OF THE BOAT RAIL. 11. DRILL A 3/16 HOLE 1 BEHIND THE SMALL BLACK PAD ON THE STARBOARD SIDE FOR THE UPHAUL BUNGEE. INSTALL THE BUNGEE WITH HOOK AND GATE USING AN 8-32 X ¾ SCREW AND NUT.
4 12. USE THE 3/16 BIT TO DRILL 2 HOLES ABOUT ¾ APART FOR THE GRAB HANDLE BUNGEE. NOTICE THE LOCATION IN THE PICTURE BELOW. 13. DRILL A ¼ HOLE THROUGH THE SIDE OF THE SEAT CLIPS ¾ DOWN FROM THE MOUNTING BOLTS. YOU MAY FIND IT EASIER TO DRILL THESE HOLE WITH THE BRACKETS REMOVED FROM THE BOAT. 14. PLACE A MARK 4 FROM THE STERN ON BOTH SIDES OF THE BOAT AT THE PARTING LINE. DRILL WITH A ¼ BIT. WITH THE DRILL STILL RUNNING, CAREFULLY LAY THE DRILL BACK TOWARD THE STERN IN LINE WITH THE PARTING LINE. THIS WILL ALLOW THE CABLES AND TUBING TO ENTER THE BOAT IN MORE OF A STRAIGHT LINE.
5 15. HOLD THE RUDDER BRACKET ON THE END OF THE BOAT WITH THE TRIANGLE END AT THE TOP. WITH THE BRACKET PUSHED TIGHT AGAINST THE STERN AND UP AGAINST THE RAIL, USE A MARKER TO MARK THE HOLE LOCATIONS. THIS MAY REQUIRE AN ASSISTANT TO MARK THE HOLES WHILE YOU HOLD THE BRACKET IN PLACE. 16. DRILL THE HOLE LOCATIONS WITH A ¼ DRILL BIT. 17. INSTALL THE BRACKET WITH THE SUPPLIED ¼-20 X 5/8 SCREWS AND NYLOK NUTS. 18. REMOVE THE 3/16 DIA. BUNGEE FROM THE STERN OF THE BOAT. INSTALL THE 12 BUNGEE IN ITS PLACE, TYING A KNOT ON EACH END.
6 19. PUSH THE ENDS OF THE SUPPLIED 20 ROPE UP THROUGH THE TWO NEW GRAB HANDLE HOLES YOU DRILLED IN STEP 7. PUSH THE ROPES THROUGH THE HANDLE AND TIE IN A KNOT. THE KNOT SHOULD PULL BACK DOWN INTO THE HANDLE. 20. PUSH THE ENDS OF THE SUPPLIED 30 BUNGEE INTO THE HOLES THAT YOU DRILLED IN STEP 11. PASS ONE LEG OF THE BUNGEE THROUGH THE HANDLE ROPE LOOP FROM THE UNDERSIDE OF THE DECK. THEN TIE THE TWO BUNGEE ENDS TOGETHER. THE BUNGEE SHOULD BE TIED TIGHT ENOUGH TO PULL THE HANDLE DOWN AGAINST THE DECK OF THE BOAT. 21. FLARE ONE END OF THE BLACK RUDDER TUBING WITH A HEAT SOURCE. FLARE THE END LARGE ENOUGH THAT IT WILL NOT PULL BACK THROUGH THE HOLES YOU DRILLED IN STEP 12.
7 22. PUSH THE TUBING INTO THE BOAT FROM THE STERN UNTIL THE FLARED END IS UP TIGHT AGAINST THE BOAT. 23. INSTALL A 1/4 P-CLIP ON THE TUBING AND INSTALL THE CLIP ON THE INSIDE OF THE BOAT ON THE BACKSIDE OF THE NEW 5 TH RIVET. 24. PUSH THE TUBING THROUGH THE HOLE YOU DRILLED IN THE SEAT CLIP. PULL TAUGHT. 25. CUT THE TUBING ABOUT ½ PAST THE SEAT CLIP. USE A HEAT SOURCE TO FLARE THE END OF THE TUBING LARGE ENOUGH THAT IT WILL NOT PULL BACK THROUGH THE CLIPS. 26. INSERT THE CABLES INTO THE BLACK TUBING FROM THE STERN OF THE BOAT. 27. REMOVE THE RUDDER PIN FROM THE RUDDER. INSTALL THE RUDDER ON THE BRACKET AND SECURE WITH THE PIN AND RETAINING RING.
8 28. PUSH THE RUDDER ROPES THROUGH THE TWO HOLES ON THE STERN OF THE BOAT THAT YOU DRILLED IN STEP INSERT A NEW RIVET INTO THE #4 LOCATION OF THE ADAPT A TRAC. INSTALL A 5/16 P- CLIP ON THE BACK OF THE RIVET. SET THE RIVET. 30. RUN THE ROPES THROUGH THE 5/16 P-CLIP. MAKE SURE THE ROPES ARE NOT TWISTED OR TANGLED. 31. PUSH THE ROPES THROUGH THE ¾ HOLE YOU DRILLED IN STEP ATTACH THE RUDDER CABLES TO THE RUDDER WITH THE CLEVIS PINS AND RETAINING RINGS. 33. ROTATE THE RUDDER BLADE SO THAT IT LIES ON THE DECK OF THE BOAT. SECURE WITH THE BUNGEE AND HOOK YOU INSTALLED IN STEP PULL THE RUDDER CABLES TAUGHT FROM THE SEAT AREA. CUT THE CABLES 13 FROM THE SEAT CLIP. 35. PUT ONE PIECE OF SHRINK TUBING AND TWO COPPER FERRULES ON EACH CABLE.
9 36. LOOP THE CABLE THROUGH THE GROMMET IN THE NEW FOOTPAD STRAP AND BACK THROUGH THE COPPER FERRULES. MAKE THE LOOP IN THE CABLE JUST BIG ENOUGH THAT IT WILL NOT BIND ON THE CORNERS OF THE WEBBING. THE CABLE SHOULD BE FLUSH WITH THE END OF THE COPPER FERRULES. 37. CRIMP THE FERRULES. USING A HEAT SOURCE, SHRINK THE TUBING DOWN ON TOP OF THE FERRULES. 38. INSERT THE NEW FOOTPADS ONTO THE FOOTRAILS. 39. USE A #8 SELF TAPPING SCREW INSERTED IN THE FRONT OF THE FOOTRAIL TO KEEP THE FOOTPAD FROM COMING OFF THE RAIL. 40. REMOVE THE HOOK FROM THE RUDDER BLADE. DETERMINE WHICH ROPE WILL ROTATE THE BLADE FROM THE DECK BY PULLING ON BOTH ROPES SEPARATLY. THE ROPE THAT MOVES THE RUDDER SHOULD PASS THROUGH THE HOOK. TIE THE TWO ROPES TOGETHER USING A BARRELL KNOT. 41. APPLY ADHESIVE ( LEXEL OR CONTACT CEMENT) TO THE TOP OF THE TRIANGULAR FLOATATION BLOCK. PUSH THE BLOCK INTO THE STERN OF THE BOAT. 42. APPLY ADHESIVE TO THE VISIBLE EDGE OF THE INSTALLED FLOATATION BLOCK. INSTALL THE BULKHEAD FLOATATION BLOCK TOP FIRST THEN PRESS AND HOLD THE BLOCK IN PLACE.
RUDDER KIT INSTRUCTIONS
A I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS TARPON 0/40/60/60i The Tarpon series is designed as a high performance sit-on-top kayak tailored for the sport paddler. Our rudder system is designed to
More informationRUDDER KIT INSTRUCTIONS
C I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS PAMLICOS-0,0,T, T, 60T, Excel Rotomolded Pamlico 0, 0, T, T, 60T, Excel The addition of a rudder to a kayak results in additional control and efficiency,
More informationINSTALLING THE TRIDENT 11, 13 OR 15 RUDDER
INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 - Rubber 2 - Rail Assemblies 1 - Rudder Body 1 - Rudder Retraction Grommets
More informationRef Part Part # Qty Letter A Rudder Catcher B X 1/2 PH Bolts C Rudder Bracket
Ref Part Part # Qty A Rudder Catcher 07.2694.0000 1 J B Q A B 10-32 X 1/2 PH Bolts 07.2136.0000 10 C Rudder Bracket 07.2689.0000 1 D Kayak Pad Eye 01.1315.0430 2 E Cherry Rivets 01.1315.0459 4 H T N P
More informationINSTALLING THE PROWLER 13 RUDDER
INSTALLING THE PROWLER 13 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 Rubber 2 Rail Assemblies Rudder Body 1 Rudder Retraction Grommets (includes steering
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO KAYAKS IMPORTANT: Tandem models will require the Wildy Supplemental kit in addition to this kit. The Supplemental kit provides extension straps and extra footbraces that allow rudder positioning
More informationASSEMBLY MANUAL HOBIE CATSY
ASSEMBLY MANUAL HOBIE CATSY HOBIE CAT EUROPE ZI Toulon Est, BP 50 8078 Toulon cedex 9, France Tel : + (0)9 08 78 78 - Fax : + (0)9 08 99 Email : hobiecat@hobie-cat.net - http://www.hobie-cat.net ASSEMBLY
More informationCamRT Sun Top Bimini Installation Instructions
CamRT Sun Top Bimini Installation Instructions C910-07 & C910-08 Rev. 16-Jun-15 Information: info@roswellglobal.com Warranty: warranty@roswellglobal.com Questions? Please call us at (31) 638-1331 Setup:
More informationBladerider X8 Assembly Help Notes
2.1 Remove All Parts & Have Some Tools Handy Remove all items from the box and identify each part as per the packing sheet and check that nothing is missing. If there is something missing, please email
More informationPT 11 trouble-shooting and maintenance.
PT 11 trouble-shooting and maintenance. Does your rudder not stay down?...your back seat slip off?...your knobs tight and your leather pads loose? Maybe we can help. We have used our PT 11 s hard enough
More informationStand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS
1 Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new Stand-N-Fish Kayak Fishing System. Once installed on your kayak the Stand-N-Fish will take your kayak fishing
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO AND TANDEM KAYAKS IMPORTANT: For Tandem kayaks, the Supplemental Kit will be needed in addition to this kit and can be purchased through a registered dealer. The addition of a rudder to
More information2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions
SECTION A: INTRODUCTION This unofficial set of installation instructions was written for a 2009 Hobie Getaway, using a 2012 Hobie Spinnaker Kit 20999020. Note from the Author: I had never seen this kit
More informationFalcon 3 145, 170, 195 and Tandem Owner / Service Manual
Falcon 3 145, 170, 195 and Tandem Owner / Service Manual January 2007 - Second Edition Removing The Sail From The Airframe And Short Packing The Glider Many maintenance and repair procedures will require
More informationHOW-TO: Install a Wildcat Lighting System
Items needed: Acetone Isopropyl Alcohol Power Drill 8 zip ties Marine Goop 9/6 Drill Bit /6 Drill Bit Pencil or dry erase marker Measuring tape Extra wire Extra Grey Wire nuts Wire cutters Wire Strippers
More informationFDR CHRYSLER 16' CATAMARAN (MUSKETEER) The initial rigging of a sailboat is not difficult, but if the boat is strange
Page of 6 Revised 2/0/76 RIGGING INSTRUCTIONS FDR CHRYSLER 6' CATAMARAN (MUSKETEER) The initial rigging of a sailboat is not difficult, but if the boat is strange to the new owner, or the new owner is
More informationOPPI Rigging Guide 3/2008
OPPI Rigging Guide 3/2008 McLaughlin Boat Works optistuff.com Thanks for purchasing OPPI, the most durable and F-U-N sailboat available. Rigging your OPPI is easy and the following pictures make it a breeze
More informationRudder Kit Assembly Instructions for Quest 13
Rudder Kit Assembly Instructions for Quest 13 Revised 4/2/2015 78501 Rudder System The Hobie Quest is designed for the addition of an optional rudder system. Rudder systems in boats like this allow you
More informationKayaking Bob s Tandem Island SpraySkirt Kit Installation Instructions
Kayaking Bob s Tandem Island SpraySkirt Kit Installation Instructions Copyright 2011 by R. E. & D. L. Conlon Kit Contains: Right & Left SpraySkirts 3 Long Black Wire Ties* 3 Short Black Wire Ties* 1 3/16
More informationInstallation Instructions
116-3027, 116-3017 X-Pando Adjustable Steel Protector Installation Instructions 1404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 NB 6/28/10 607-0112 Step 1. Mounting
More informationInstallation Guide, MPower Echelon Console
Installation Guide, MPower Echelon Console AC Performance, AC Sport and AC Performance Plus Schwinn Echelon Console (External Routing) 1. Install batteries to console. Mount the console to the bike. 2.
More informationWeta Basic Rigging Guide
Weta Basic Rigging Guide A quick reference guide of how to rig your Weta, with some tips to make rigging quick and easy! For a more indepth guide see our Weta Manual under Weta Owners on the website. 1.
More informationMount the actuator in the bracket provided and install a 24-foot EFTC cable to the actuator.
. Mount the actuator in the bracket provided and install a 4-foot EFTC cable to the actuator. Route the cable through left stanchions,, and 4. Be sure that the cable does not contact any spring or push
More informationTable of content Introduction 5 1. Part 1. Assembly Tools needed for Assembly Glossary Hulls Mounting the beams 7
Table of content Introduction 5 1. Part 1. Assembly 6 1.1. Tools needed for Assembly 6 1.2. Glossary 6 1.3. Hulls 7 1.3.1. Mounting the beams 7 1.3.2. Fixing the mast rotation cleats 8 1.3.3. Placing the
More informationSTERN MOTOR FOOT CONTROL KIT For use with the Torqeedo 403 Ultralight
STERN MOTOR FOOT CONTROL KIT For use with the Torqeedo 403 Ultralight The Wilderness Systems Foot Control Kit is designed to connect directly to a Torqeedo 403 Ultralight motor mounted on the stern of
More informationLectric Cycles Mid-Drive Electric Motor Installation
Lectric Cycles Mid-Drive Electric Motor Installation This write-up describes the installation of a Lectric Cycles electric motor. The model is the e-rad Mid-Drive 750 Watt conversion kit, installed on
More informationAssembly instructions nortik scubi 2 Recreational kayak
Assembly instructions nortik scubi 2 Recreational kayak QR-Code assembly video: Assembly instructions nortik scubi 2 Dear Customer, You have purchased a nortik scubi 2, an innovative hybrid kayak for recreational
More informationAdvancedTrak Rudder Kit AE4005. Assembly and Installation Instructions
AdvancedTrak Rudder Kit AE4005 Assembly and Installation Instructions Thank you for your purchase of the Advanced Elements AdvancedTrak Rudder Kit! A Kayak Rudder is a great way to enhance the tracking
More informationPARTS - FORWARD. Kayaking + Fishing Parts & Accessories Hook HATCH SEAL "TRIM-LOC" (TOP MOLDED) 5 REQ
PARTS - FORWARD 72104001 Hook 71301001 HATCH SEAL "TRIM-LOC" (TOP MOLDED) 5 REQ 71302001 HULL FLANGE SEAL (pre 2012 ADV) "TRIM-LOC" (SIDE GLUED) 5 REQ 80012001 Pedal Retainer Bungee w/ Hook 84560001 Mast
More informationPico rigging manual 2007.doc Page 1 of 28
Pico rigging manual 2007.doc Page 1 of 28 Pico Rigging Instructions The Pico rigging instructions are a guide to rigging your boat. Due to production supplies certain parts may be slightly modified from
More informationPre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender
Pre-Paint>Fuselage>Empennage>Fit vertical tail fin Objectives of this task: To fit the vertical tail fin to the fuselage, including fitting the static probe, static tube, optional strobe light wiring and
More informationCHAPTER 5 REWIND STARTERS
GENERAL INFORMATION CHAPTER 5 REWIND S Rewind starters used on vertical shaft Tecumseh engines are top mount horizontal pull style or side mount vertical pull style. Horizontal shaft engines use side mounted
More informationSEADUCER BOATS GAS SPORT HYDRO
SEADUCER BOATS GAS SPORT HYDRO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 2 - Pkg. Of 440 push rod ends 2 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 30" flex
More informationFar East Boat Optimist Rigging Instructions
Far East Boat Optimist Rigging Instructions These instructions are written specifically for Far East Boats Championship and Racing Optimist. Parts of the Optimist PAGE 1 Sprit Wind Indicator Sail Mast
More informationINSTALLATION AND OPERATING INSTRUCTIONS. T10219-AD Deckboat 40 with AutoDeploy and Wireless Remote Control
INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCH T10219-AD Deckboat 40 with AutoDeploy and Wireless Remote Control If you have any questions or difficulty installing this product, we are here to help!
More information2019 MADONE ASSEMBLY MANUAL
2019 MADONE ASSEMBLY MANUAL 2019 MADONE Rim brakes and Di2 drivetrain Rim brakes and mechanical drivetrain Disc brakes and Di2 drivetrain Disc brakes and mechanical drivetrain TABLE OF CONTENTS Common
More informationFor ELECTRIC ANCHOR WINCH Models: T Pontoon 35 T sw Salt Water Series Coastal 35
INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCHES For ELECTRIC ANCHOR WINCH Models: T10109-35 Pontoon 35 T10102-35sw Salt Water Series Coastal 35 If you have any questions or difficulty installing
More informationFor ANCHOR WINCH Model: T Big Water 45 T sw Salt Water Series Big Water 45
INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCHES For ANCHOR WINCH Model: T10110-45 Big Water 45 T10103-45sw Salt Water Series Big Water 45 If you have any questions or difficulty installing this
More informationINSTALLING YOUR CLC RUDDER
INSTALLING YOUR CLC RUDDER These instructions are written to help you install the CLC rudder kit on your wooden kayak. The rudder can be fitted to your boat during construction or after completion. Please
More information400/488 Rotating Davit Installation Instructions
400/488 Rotating Davit Installation Instructions These instructions were written with the owner in mind. If you are the installer make sure these instructions are passed along to the owner of the boat.
More informationClub 420 Class Rigging Manual
Club 420 Class Rigging Manual Performance sailcraft 2000 Inc 2555 Dollard Lasalle, Quebec, H8N 3A9 Tel: 514 363 5050 email: info @ps2000.ca Website: www.ps2000.ca Mast set up Remove the pole and unwrap
More informationInstallation Instructions - Electric Steel Drive Systems for Arm Sets to ,
Installation Instructions - Electric Steel Drive Systems for Arm Sets to 22 208-025, 209-025 NB /0/ 607-0029 404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 Step.
More informationINSTRUCTION NO
INSTRUCTION NO. 14138 Dagger Rigging Instr. P~e 2.of 6 MODEL 244 CHRYSLER "DAGGER" SAILBOAT RIGGING INSTRUCTIONS We, at Chrysler Boat Corporation, congratulate you on your selection of our Model 244 "Dagger"
More informationQUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift
INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More informationInstruction Manual. Features. Specification: Length: 730mm Width: 500mm Height: 1000mm Sail Area: 0.15m 2. Weight: 692g (w/o battery & receiver)
AN UNBELIEVABLE SPEED MACHINE Instruction Manual Features Specification: Length: 730mm Width: 500mm Height: 1000mm Sail Area: 0.15m 2 Weight: 692g (w/o battery & receiver) Thank you for purchasing your
More informationNAVIGATOR PROP BUILDING INSTRUCTIONS & PHOTOS
NAVIGATOR PROP BUILDING INSTRUCTIONS & PHOTOS Science under the ice Ice sheet At regional competitions the ice is simulated by 8 ft x 4 ft ½-inch foam sheeting (Home Depot part #703990 [in store only],
More informationBike Rack and Tire Carrier
Bike Rack and Tire Carrier OWNER'S MANUAL Rev: 10.26.2017 Page 1 Bike Rack and Tire Carrier Owners Manual TABLE OF CONTENTS System 2 Description 2 Prior To Operation 3 Manual Slide-Out Bike Rack Operation
More informationIndex 1. Trampoline 2. Main Foils 3. Spinnaker Pole 4. Mast Setup 5. Mast Rigging 6. Rig Tension 7. Trapeze Lines 8. Rudders 9. Boom 10. Main Sheet an
By User Manual Index 1. Trampoline 2. Main Foils 3. Spinnaker Pole 4. Mast Setup 5. Mast Rigging 6. Rig Tension 7. Trapeze Lines 8. Rudders 9. Boom 10. Main Sheet and Traveler 11. Main Sail 12. Downhaul
More informationConstitution Instructions
Constitution Instructions This kit will build a 1:48 scale hull for the USS Constitution frigate. The kit contains the following parts. 1/8 deck with laser etched deck lines 1/8 railing Ribs Center keel
More informationInstallation of 2 Tier In Line Greeting Card Rack
Installation of 2 Tier In Line Greeting Card Rack Material Sent to Store: Greeting Card Fixtures: 4ft Inline Tier Kit (1 per every 4ft based on planogram) 3ft endcap Tier Kit (will not receive if planogram
More informationTM D E A L E R C A T A L O G
2019 DEALER CATALOG TM TM NEW 2019 FOR Cheek Block K082200-1 Zig Cleat K043550-1 Ring Clip K199250-1 Accessory Track 4" K736104-1 8" K736108-1 12" K736112-1 16" K736116-1 Webbing Clip K199200-1 Paddle
More informationHobie Island Spinnaker Instructions
Hobie Island Spinnaker Instructions Please read through the instruction manual before using this product. 2 Installation Components 1. 2. 1. Swivel Cam Cleat 2. Mount for Cleat w/ Hardware 3. Padeye w/
More informationFitting Instructions for Single Line Mainsail Reefing System For Yachts Up To 9m (30ft) - Part No
Fitting Instructions for Single Line Mainsail Reefing System For Yachts Up To 9m (30ft) - Part No. 41 130 This single line reefing kit allows reefing control lines to be led aft to the safety of the cockpit.
More informationINSTRUCTIONS FOR CHAIN LINK INSTALLATION
INSTRUCTIONS FOR CHAIN LINK INSTALLATION This guide explains how to correctly install our chain link fencing and post system. The guide provides details of which post type you will need for your fence
More informationUser s Manual. Model SWTC800. CAUTION: Adult Assembly Required
User s Manual Model SWTC800 CAUTION: Adult Assembly Required Model SWTC800...3...4...4...5...6.........8...9...10-11 Part Identification Chart... 12 Exploded Drawing and Parts List...13-14 Ordering Replacement
More informationInstallation Instructions - Electric Aluminum Drive Systems for Arm Sets to 22 Electric Arm Systems , ,
Installation Instructions - Electric Aluminum Drive Systems for Arm Sets to 22 Electric Arm Systems - 204-025, 206-025, 22-025 NB /0/ 607-0020 404 N. Marshall Ave. El Cajon CA. 92020 For technical support
More informationCRUZBIKE Quest 2.0 Assembly
CRUZBIKE Quest 2.0 Assembly CRUZBIKE Quest 2.0 Assembly... 1 General notes on assembly... 2 Un box and evaluate the frame and major parts... 2 Unfold the rear swing arm and arrange the frame... 3 Rear
More informationPIVOT SHUTTLE Dropper Post Cable Housing Replacement Maintenance Procedure
PIVOT SHUTTLE Maintenance Procedure This maintenance guide provides detailed instructions to replace the dropper post cable housing on the Pivot Shuttle should something malfuction or break. If these steps
More informationINSTALLATION INSTRUCTIONS
EDGEMERE CENTERSET LAVATORY FAUCET INSTALLATION INSTRUCTIONS 708.0 Thank you for selecting American Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds
More informationCO V E R S TA R AU TO MAT I C S A F E T Y CO V E R INSTALLATION GUIDE
CO V E R S TA R AU TO MAT I C S A F E T Y CO V E R DECKMOUNT SYSTEM INSTALLATION GUIDE SECTIONS System Parts Reference...3 Standard Top Track...4-6 Mechanism... 7-10 Cover Fabric...11-16 Home Owner & Builder
More informationRANGER PROP BUILDING INSTRUCTIONS & PHOTOS
RANGER PROP BUILDING INSTRUCTIONS & PHOTOS Science under the ice Ice sheet At the international competition, the science under the ice product demonstration will take place under an actual sheet of ice.
More informationSECTION 2 RING MOUNT
SECTION 2 RING MOUNT Rotax aircraft engines are manufactured and supported by Rotax GmbH of Austria. Read and understand the Rotax manuals completely before starting with the engine installation, as they
More informationM32 CATAMARAN ASSEMBLY MANUAL
M32 CATAMARAN ASSEMBLY MANUAL 1 M32 CATAMARAN ASSEMBLY MANUAL MANUAL SUMMARY M32 ASSEMBLY Parts and tools Instructions MAST PLATFORM Parts and tools Instructions MAST STEPPING Instructions MAIN HALYARD
More informationRigging Manual. 1 Parts of the Hull. 2 Parts of the Sail. 3 Sunfish Mast Kit. 4 Bailer Installation. 5 Ratchet Block Installation
SUNFISH SUNFISH RACE SUNFISH Rigging Manual 1 Parts of the Hull Go-fast tip number one: Read this rigging guide first. 2 Parts of the Sail 3 Sunfish Mast Kit 4 Bailer Installation 5 Ratchet Block Installation
More informationInstalling a Tiller Pilot on a Double Ended Yacht
Installing a Tiller Pilot on a Double Ended Yacht My Frances 26, Tom Thumb is a classic yacht with a double ended (canoe) stern. I found it difficult to install a tiller pilot (a Raymarine ST1000+) as
More informationInuit Owners Manual. Inuit 13.5
Inuit Owners Manual We have advanced the design and comfort level of the Inuit series beyond any other touring kayak. The Tru-Track hull offers straight tracking despite the shorter hull length plus it
More informationMainz Product Catalogue
2019 Mainz Product Catalogue Stainless steel wire, fittings, hardware and tools for wire balustrades Stainless steel wire Stainless steel hardware and fittings Tools Mainz Pty Ltd Ph: (08) 92756246 www.wirebalustrades.com.au
More informationA-FRAME RESIN IN & OUT FLIP UP LADDER
A-FRAME RESIN IN & OUT FLIP UP LADDER NE1222 NOTE FOR SAFETY PURPOSES ALL LADDERS SHOULD BE SECURED BY ATTACHING THEM TO THE TOP LEDGE OF THE POOL. (See step 13 for details) In order for the ladder to
More informationTABLE OF CONTENTS FRAME FEATURES INTRODUCTION
S3 DISC MANUAL TABLE OF CONTENTS Introduction...1 Frame Features...2 Fork Preparation...3 Small Parts...5 Frame Preparation...6 Brake Housing Installation...7 Mechanical Cable Routing...9 Electric Cable
More information3. Sail Kit. Table of Contents: Portland Pudgy Safety Dinghy: 3. Sail Kit
Table of Contents: 3. Sail Kit Sailing the Portland Pudgy... 1 Sailing Tips... 1 Reducing the Sail Area (Reefing the Sail)... 2 Method 1. Reducing Sail without the Exposure Canopy... 2 Method 2. Reducing
More informationEZ-Mount 4 Spring Enclosed System to 22 (Low & High Mount Applications) Installation Instructions
501-1768 (With Wire) 501-1769 (No Wire) 501-1766 (With Wire) 501-1767 (No Wire) 607-015 WLH 06/20/18 TABLE OF CONTENTS ***Assembly*** ***Parts*** Pivot Points and Mounting Locations (Low Mount)... 1 High
More informationwww.myrower.com support@myrower.com ASSEMBLY Congratulations on purchasing the MyRower! Please see the following pages for instructions on assembling your MyRower. Bits bag contents: Rail Cross Bolt (90mm)
More informationImport Bike Rack OEM INSTALLATION MANUAL
Import ike Rack OEM INSTLLTION MNUL TLE OF ONTENTS System Information 2 Safety Information 2 Resources Required 3 Preparation 3 Under umper ttachment 3 Over umper ttachment 3 Installation 3 Under umper
More informationSCUBAPRO. Balanced Power Inflator
SCUBAPRO Balanced Power Inflator USE THIS GUIDE AS A REFERENCE WHEN SERVICING THE BALANCED POWER INFLATOR Important note: The following information is not designed to be a complete training guide for servicing
More informationF-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN F-1281-R LOWER RIGHT SKIN F-1208-R FUSELAGE FRAME
F-1282-R BOTTOM RIGHT SKIN F-1283C J-STIFFENER F-1278 TOP SKIN F-00009-L ADAHRS BRACKET F-00009-R ADAHRS BRACKET F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN SECTION 10: TAILCONE F-1279-L UPPER LEFT
More informationFollow these easy steps to properly assemble your new Zim 420
Thank you for buying a Zim 420 and welcome to the Zim Sailing family. We are extremely proud of the quality of our boats and the race results are proven. Many of the top sailors are choosing Zim over other
More informationWysiwig - Wayfarer Rigging Guide
Wysiwig - Wayfarer 8767 - Rigging Guide GENERAL NOTES Before you go afloat, make sure that the self-bailer is closed. It is operated through the cut-out in the starboard floorboard. If you do not close
More informationHOBIE TEDDY ASSEMBLY MANUAL
ASSEMBLY MANUAL HOBIE TEDDY HOBIE CAT EUROPE ZI Toulon Est, BP 50 83078 Toulon cedex 9, France Tel : +33 (0)494 08 78 78 - Fax : +33 (0)494 08 3 99 Email : info@hobie-cat.net - http://www.hobie-cat.net
More informationU STAND INSTALLATION INSTRUCTIONS
U STAND INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new U STAND by Stand N Fish. Once installed on your kayak the U STAND will enhance your kayak fishing enjoyment to a whole new
More informationThank you for purchasing a WIKE BOX BIKE!
Thank you for purchasing a WIKE BOX BIKE! Contents Safety.....3 Front wheel.4 Kickstand..5 Handle Bar & Box 6 Seat post and Saddle 7 Final pre-ride check 8 Tools needed to assemble Bike: -High table or
More informationDolly wheels in slot #8 for Boat #10.
Rigging: Laser SAIL SELECTION: The International Laser Class has three different official rigs. Each sail is designed for sailors of different weights. The Standard Rig was designed for sailors weighing
More information1 Parts of the Hull. 2 Parts of the Sail. 3 Sunfish Mast Kit. 4 Bailer Installation. 5 Ratchet Block Installation
SUNFISH SUNFISH RACE SUNFISH Rigging Manual Go-fast tip number one: Read this rigging guide first. 1 Parts of the Hull 2 Parts of the Sail 3 Sunfish Mast Kit 4 Bailer Installation 5 Ratchet Block Installation
More informationSCOUT PROP BUILDING INSTRUCTIONS & PHOTOS
SCOUT PROP BUILDING INSTRUCTIONS & PHOTOS Companies should be aware that tolerances in lengths of pipe and length of pipe inserted into joints can change the overall dimensions of product demonstration
More informationSEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT
SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 1 - Pkg. Of 440 push rod ends 1 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 24" flex shaft
More informationIn each step, the needed parts are shown the number right below. Locate all parts for the step.
Tools Required for Assembly Phillips Screwdriver, Med Needle Nose Pliers Sandpaper (#400 grit) Hobby Knife Scissors CA Instant Glue Rubbing Alcohol Drill Bit 1/16", 1.6mm 5/64, 2mm 1/8, 3mm 5/32, 4mm Before
More informationFRAME FEATURES TABLE OF CONTENTS INTRODUCTION. A guide to your Cervélo C Series frame.
C SERIES MANUAL TABLE OF CONTENTS Introduction...1 Frame Features...2 Fork Preparation...3 Small Parts...5 Frame Preparation...6 Brake Housing Installation...7 Mechanical Cable Routing...9 Electric Cable
More informationTrampoline Installation Instructions
Congratulations on purchasing an Oz Trampolines Product. Following are detailed setup instructions for your trampoline. Please ensure all boxes and parts are present before continuing. Setting Up Your
More informationWing assemblyfinal Master 4/29/04 11:20 PM Page 1. Issued January 1, Sabre Aircraft. Assembly Manual. Sabre 16ss Wing
Wing assemblyfinal Master 4/29/04 11:20 PM Page 1 Issued January 1, 2002 Sabre Aircraft Assembly Manual Sabre 16ss Wing Wing assemblyfinal Master 4/29/04 11:20 PM Page 2 1. 2. 1. Unzip the cover and remove
More informationVR SERIES TECHNICAL MANUAL
VR SERIES TECHNICAL MANUAL INTRODUCTION CONTENTS VR SERIES Congratulations on purchasing a VR Series. As with all of our bikes and components, our aim is to provide the rider with the best product and
More informationInstallation Instructions for the AlphaDeck Staging System
Installation Instructions for the AlphaDeck Staging System Step 1 - Preparation A. Before setting up this system, determine the location of the stages and all the parts you will need. B. Read through the
More informationPlace a rope coil here
1 2 3 4 The anchor buoys were made from Sculpey. You could however, carve them from wood but I wanted to continue my experimentation with this material. A buoy from this time period would have ranged from
More informationREPLACING THE AFT RUDDER CABLES
REPLACING THE AFT RUDDER CABLES Note: You must have the assistance of a qualified Aircraft Mechanic to perform this procedure. A logbook entry with the mechanics signature is required. Please read these
More informationInstalling N-Strike Recon CS-6 Stage 1 and Stage 2 Performance Kits
Installing N-Strike Recon CS-6 Stage 1 and Stage 2 Performance Kits The Nerf N-Strike Recon CS-6 is a currently available blaster that is relatively easy to modify. The guys at Orange Mod Works have produced
More informationPressure Dump Valve Service Kit for Series 3000 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 000 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00, 400, 500, and 700 applicator
More informationEZee Glider Manual. Tools needed for Assembly: Wrench (included) Philips Screwdriver (not included) Assembly Instructions
EZee Glider Manual Congratulations on your purchase of the EZee Glider! Your glider is designed for years of nearly carefree use by your child. These instructions include how to set up your glider and
More informationa WOW Lab Prep Instructions
Pulleys and Mechanical Advantage A major step in the prep of this activity is choosing a good location. A key feature is an easily accessible top anchor. Some examples of good anchors are a solid tree
More informationInstallation Instructions for your Winter Storage Cover
Installation Instructions for your Winter Storage Cover QUINTE CANVAS MANUFACTURING 1120 CLYDE COURT, KINGSTON, ONTARIO K7P 2E4 (613) 384-6316 (613) 384-0002 Fax topshop@kos.net www.topshop.on.ca Before
More informationFinal Assembly Instructions Bikes with Threaded Headsets
Final Assembly Instructions Bikes with Threaded Headsets Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our
More informationProcedures for Winter Sailing
Procedures for Winter Sailing With winter upon us, most of the Cal 20 s (keelboats) are now in the boat yard for maintenance and storage. However, we keep two of the Cal 20 s in the water for winter sailing.
More information