Masthead Sensor Installation Guide
|
|
- Marvin Willis Scott
- 5 years ago
- Views:
Transcription
1 2315 1/2 Artesia Blvd. Redondo Beach, CA (310) (310) Fax Masthead Sensor Installation Guide
2 2.3 Masthead Sensor Installation Continued INSTALLATION BEFORE STEPPING Using the sensor's ---mounting base as a template, with the taller end of the base toward the stern, drill two 0.20-inch diameter holes in the end of the mast. Tap these holes with the ~-20 tap. Mount ~ the base with the taller end aft and secure loosely with the bolts and lock-washers provided. It is not recommended that the staff, vane, and tricup sensor be mounted before stepping in order to avoid damage to these components. 1. If the MK Mast-Base Junction Box is used, the mast cable must be cut into two custom lengths. These lengths can best be determined by first positioning and mounting the Junction Box in a dry area near the mast step. relatively The box is secured by its two mounting ears using ~-inch hardware. Mounting ear centers can be measured at inches or use the box's base as a template. 2. Measure the length from the top edge of the sensorj,s mounting base to the mast base and from the mast step to the terminal strip inside the junction box. Then add 6 inches for cable stripping. Cut the mast cable to this total length as measured from the single-connector end of the cable. the first cable required. This is 3. To make the second cable required, measure the length from the rear of the indicator I s case to the terminal strip inside the junction box. Then add 6 inches for cable stripping. of mast cable (from step 3) Cut the remaining piece to this total length as measured from the dual-connector (plus ground wire) end of the cable. NOTE: 00 NOT CUT THE MAST CABLE AT THE MASTHEAD OR INSIDE THE MAST ITSELF. -7-
3 2.3 Masthead-_Sensor Installa tion Continued Installation Before Stepping Continued 4. Drill two 3/S-inch holes in the mast, one near the top and the other recoiimlended near the mast base, to accomodate the mast cable. Insert a grommet in each hole; this grommet must accomodate a 3/S-inch hole and the thickness of the mast wall. 5. Run the mast cable with the single connector down the inside of the mast, starting at the masthead with the cut end, through the grammeted holes. The connector-end must remain at the masthead. On a mast with internal halyards, protect the mast cable by first inserting a PVC (polyvinylchloride) tube down the length of the mast. Secure the tube away from the halyards. Then run the mast cable inside the tube. 6. Mount a cable strain-relief clamp or strap to the mast immediately above the grammeted cable entrance hole near the masthead. This clamp is to be-placed around the mast cable to hold it secure. Once the mast is stepped, this clamp will virtually eliminate strain on the upper connectors INSTALLATION AFTER STEPPING AND RIGGING Storage or shipment of the masthead sensor on its side or upside down may allow oil seepage from the vane's hydraulic damping assembly. This oil seepage is normal and will not affect operation of the sensor if it is cleaned off just prior to mounting. Pay special attention to cleaning the area between the staff and dust shield. -8-
4 2.3 Masthead Sensor Installation Continued Installation After Stepping and Rigging Continued 1. Before going up the mast and installing the sensor: A. The wind vane's dust shield must be aligned. Turn the dust shield (see Figure 3A) until the FWD Do notch matches the white alignment mark on the sensor's upper body. R. Hold the dust shield in place. Then, if the staff will be installed pointing aft as recommended, mount the vane on top of the dust shield pointing over the staff (see Figure 3B). If the staff will point to the bow, the vane must point to the bow. C. Remove the lock-nut and washer from the bottom windspeed-end of the sensor's body. Install the tri-cup by fitting it over the ~ remaining nut. The recessed area of the tricup must face upward. Replace the locknut and washer and firmly tighten. 2. Take the completed masthead sensor assembly up the mast, place the staff in the mounting base, insert the mounting bolts, and proceed to adjust the staff angle until the sensors body is perpendicular to the water. Three staff adjustment posi~ tions are provided on the sensor's mounting base. If more adjustment is required, use a shim under the mounting base. 3.. With the mounting-base bolts loose, align the staff with the backstay so the sensor assembly is parallel with the fore-aft axis. Firmly tighten all mounting-base bolts. 4. Connect the masthead sensor cable connector to the mast cable connector. Dress the cable and tighten the cable strain-relief clamp or strap. -9-
5 FORWARD VIEW FWD 60' 30' O' 30-60'...---DUST SHIELD Figure 3A. Alignment of wind vane dust shield. AFT VIEW,":." AFT 180' Figure 38. A.Iignment of wind vane dust shield.
6 2.3 Masthead Sensor Installation Continued Installation After Stepping and Rigging Continued 5. Seal all holes, including the grommeted cable hole, with silicone sealant. 6. At the mast base, gen ly pull any loose cabling through the grommeted hole. Seal the hole with silicone sealant. 7. Disassemble the top of the junction box and loosen both waterproof cable feedthroughs (see Figure 4 ). Feed the cut end of the mast cable all the way through the nearest feedthrough. Firmly tighten the -eedthrough. 8. Strip the outer jacket of the mast cable back about 3 to 4 inches. Then strip each individual wire back about ~-inch. Connect each wire to its nearest respective color-coded terminal (i.e., black wire to BLACR terminal, etc.). The shield of the mast cable is connected to the nearest SHIELD terminal. 9. Feed the cut end of the cable length with two connectors through the remaining junction box feedthrough. Firmly tighten the feedthrough. 10. Strip the outer jacket of this second cable back about 3 to 4 inches. Then strip eacb individual wire back about ~-inch. Connect eac wire to its remaining respective color-coded terminal (i.e., black wire to BLACK terminal, etc.). The shield of this second cable is connected to the remaining SHIELD terminal. ll~. Reassemble the top of the junction box. -10-
7 Q) BLACK 1 1 ORANGE 2 2.;10 YELL.OW 3 3 +'b~ BLUE 4 4 RED 5 5.' WHITE 6 6 WATERPROOF GREEN 7 7 WATERPROOF CABLE CABLE FEEDTHROUGH PURPLE 8 8. FEEDTHROUGH (LOOS.EN BEFORE (LOOSEN BEFORE FEEDING CABLE) SHIELD 9 9 FEEDING CABLE) <Q) - Figure 4; Junction box cable connections (top removed).
SL6D. SIGNETMarine. Instruction Manual Gothard Street Unit E Huntington Beach, CA [8(0) The measure of excellence
SIGNETMarine The measure of excellence SL6D Instruction Manual Corporate Heodquort;ers: 16321 Gothard Street Unit E Huntington Beach, CA 92647 [8(0) 227-4607 INTRODUCTION WINOPOINT/WINOSPEEO SYSTEM SL
More informationINSTALLING THE PROWLER 13 RUDDER
INSTALLING THE PROWLER 13 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 Rubber 2 Rail Assemblies Rudder Body 1 Rudder Retraction Grommets (includes steering
More informationINSTALLING THE TRIDENT 11, 13 OR 15 RUDDER
INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 - Rubber 2 - Rail Assemblies 1 - Rudder Body 1 - Rudder Retraction Grommets
More informationSECTION 10iS: TAILCONE
VAN'S AIRCRAFT, INC. F-1282-R BOTTOM RIGHT SKIN F-1283C J-STIFFENER F-1278 TOP SKIN F-00009-L ADAHRS BRACKET F-00009-R ADAHRS BRACKET F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN SECTION 10iS: TAILCONE
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More informationVERSA BIKE RACK INSTRUCTIONS
VERSA BIKE RACK INSTRUCTIONS Models #8, 8 Important This rack is designed for use with a or. receiver hitch. The rack is designed to hold a maximum of two bicycles. Do not use it for anything other than
More informationF-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN F-1281-R LOWER RIGHT SKIN F-1208-R FUSELAGE FRAME
F-1282-R BOTTOM RIGHT SKIN F-1283C J-STIFFENER F-1278 TOP SKIN F-00009-L ADAHRS BRACKET F-00009-R ADAHRS BRACKET F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN SECTION 10: TAILCONE F-1279-L UPPER LEFT
More informationI.H.S INSTALLATION INSTRUCTIONS
I.H.S INSTALLATION INSTRUCTIONS TOOLS REQUIRED The following tools will be required for installation of your I.H.S. system. Item Qty Needed 9/16 Open End Wrench 2 3/4 Open End Wrench 1 1/2 Open End Wrench
More information#59114 Rola 2-Bike Rack Carrier (Shown Assembled) (A) (C) (B)
Use for Parts: #59114 Rola -Bike Rack System #59115 Rola 1-Bike Add-On TOOLS REQUIRED 10mm or 13/3 Socket & Wrench #59114 Rola -Bike Rack Carrier (Shown Assembled) Tray Attachment Hardware: (3) Plastic
More information2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions
SECTION A: INTRODUCTION This unofficial set of installation instructions was written for a 2009 Hobie Getaway, using a 2012 Hobie Spinnaker Kit 20999020. Note from the Author: I had never seen this kit
More informationInstallation Instructions MODEL VSTI-A020 Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Versa Steel Inc. Guide Cables No
Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Guide Cables No Guide Cables 1 August 4, 2011 Assembly Instructions: (Shown with a 2 board, 12 ft kit) ITEM NO. PART NUMBER DESCRIPTION
More informationWIND CLIPPER KTS ILLUM SCALE INC DEC CLIPPER WIND SYSTEM
CLIPPER WIND KTS ILLUM SCALE DEC INC CLIPPER WIND SYSTEM TABLE OF CONTENTS INTRODUCTION PRE-TEST OF INSTRUMENT INSTALLING THE MASTHEAD SENSOR UNIT INSTALLING THE DISPLAY NORMAL OPERATION CHANGING THE
More informationQUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift
INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your
More informationSHEET 2: VERTICAL INSTALLATION
IMAGE OW1291 OW1293 OW1295 OW1297 AVATAR OW1301 OW1303 OW1305 OW1307 OW1311 OW1313 OW1315 OW1317 OW1331 OW1333 OW1335 OW1337 SHEET 2: VERTICAL INSTALLATION SHEET 3: HORIZONTAL INSTALLATION Drawing: 760883XX
More informationTripod Setup Guide (M-TPx)
Items needed: 1/2 inch wrench, mast level (M-MLA), medium size wire cutters, crescent wrench, all-purpose grease, tape measure, tie wraps, redi-mix cement (optional), shovel (optional), sledge hammer (for
More informationRAI-M series RUDDER ANGLE INDICATOR SYSTEM
RUDDER ANGLE INDICATOR SYSTEM RAI-M series SEAFIRST ENGINEERING CO 45-16, Ga Um Dong, Chang Won, Kyong Nam Korea Tel : 82 55 267 1645 Fax ; 82 55 266 1646 http://www.seafirst.co.kr GENERAL Seafirst Rudder
More informationRef Part Part # Qty Letter A Rudder Catcher B X 1/2 PH Bolts C Rudder Bracket
Ref Part Part # Qty A Rudder Catcher 07.2694.0000 1 J B Q A B 10-32 X 1/2 PH Bolts 07.2136.0000 10 C Rudder Bracket 07.2689.0000 1 D Kayak Pad Eye 01.1315.0430 2 E Cherry Rivets 01.1315.0459 4 H T N P
More informationFIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions
FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions WARNING! WARNING! WARNING! THIS BASKETBALL SYSTEM IS SPRING LOADED AND SHIPPED UNDER TENSION. ATTEMPTING TO ASSEMBLE OR DISASSEMBLE ANY
More informationTechnical Bulletin. Parts and Service News. LPG Lock-Off valve replacement procedures for 4.2 Liter Ford V6
Equipment Affected Technical Bulletin LPG Lock-Off valve replacement procedures for 4.2 Liter Ford V6 Ford 4.2L V-6 powered tractors with LPG fuel systems. Part Description Discrepancy Fuel Pressure Lock-off
More informationIndustrial cable glands
Industrial cable glands SK-EMC cable glands Cable glands of the SK-series fulfil the highest demands of quality and security. Outstanding high-grade materials are used together with innovative technology
More informationCable Replacement Instructions for R-Series Roust-A-Bout 100/150/250
Cable Replacement Instructions for R-Series Roust-A-Bout 100/150/250 US 7514 Alabonson Road Houston, TX 77088 phone: 281-999-6900 fax: 281-999-6966 Canada 1721 Bishop St. Unit #4 Cambridge, ON N1T 1N5
More informationChapter 2 Rigging. Cutting Wire Rope. Anchoring Wire Rope to Drum. Winding Wire Rope Onto Drum
Chapter 2 Rigging Cutting Wire Rope The wire rope must be tightly seized on both sides of the point where the wire rope will be cut, as shown in Figure 2-1. Seize the wire rope with either seizing wire
More informationHobie Island Spinnaker Instructions
Hobie Island Spinnaker Instructions Please read through the instruction manual before using this product. 2 Installation Components 1. 2. 1. Swivel Cam Cleat 2. Mount for Cleat w/ Hardware 3. Padeye w/
More informationVK/VP SERIES : Sealless Vertical Pump. Assembling Instructions 2010
VK/VP SERIES : Sealless Vertical Pump Assembling Instructions 2010 20610 Manhattan Place Suite 116 Torrance, CA 90501 Phone: 310-328-9114 Fax: 310-328-9441 1. Motor Shaft and Pump Base (1) (2) Place a
More informationInstallation Guide, MPower Echelon Console
Installation Guide, MPower Echelon Console AC Performance, AC Sport and AC Performance Plus Schwinn Echelon Console (External Routing) 1. Install batteries to console. Mount the console to the bike. 2.
More informationRUDDER KIT INSTRUCTIONS
C I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS PAMLICOS-0,0,T, T, 60T, Excel Rotomolded Pamlico 0, 0, T, T, 60T, Excel The addition of a rudder to a kayak results in additional control and efficiency,
More informationE Manual Self tacking system 30
597-205-E 2015-12-09 Manual Self tacking system 30 1 Self tacking system 30, 443-200-10 A self-tacking jib makes life on board a lot easier, in particular for shorthanded crews. The jib sheet is led to
More informationUnderwater Fiber-Optic Plane Irradiance Collector
Underwater Fiber-Optic Plane Irradiance Collector User s Manual Revision F, October 2018 Hōbi Instrument Services www.hobiservices.com Revisions F October 2018, improved illustrations, table of immersion
More informationSpectrum AquaLight (SAL ) Color Underwater Light Owner s Manual
Spectrum AquaLight (SAL ) Color Underwater Light Owner s Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents Section I. Installing Light Fixture
More informationParts: Included in the parts box: Inner Rear Tire Tray. Inner Front Tire Tray. Trail Doc Clamp. Pivot Assembly. Trail Doc Post.
NV 2.0 2 Parts: Outer Front Tire Tray Inner Front Tire Tray Outer Rear Tire Tray Inner Rear Tire Tray Pivot Assembly Trail Doc Clamp Trail Doc Post Included in the parts box: 6mm Allen Wrench M6 Lock Washer
More informationINSTRUCTIONS 360 Y-DROP HAGIE STS 2015
INSTRUCTIONS 60 Y-DROP HAGIE STS 05 INSTRUCTIONS 60 Y-DROP HAGIE STS 05 INTRODUCTION Before beginning, it s important to know where each mounting bracket fits relative to the row spacing involved. The
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO KAYAKS IMPORTANT: Tandem models will require the Wildy Supplemental kit in addition to this kit. The Supplemental kit provides extension straps and extra footbraces that allow rudder positioning
More informationFalcon 3 145, 170, 195 and Tandem Owner / Service Manual
Falcon 3 145, 170, 195 and Tandem Owner / Service Manual January 2007 - Second Edition Removing The Sail From The Airframe And Short Packing The Glider Many maintenance and repair procedures will require
More information! CAUTION! ! WARNING! General Information
Great Plains Mfg., Inc. Installation Instructions Used with: 2SF24, 24-Foot Two-Section Drill General Information Two-Section, Hydraulic Folding Marker 2SF30, 30-Foot Two-Section Drill 2SBM30, 30-Foot
More informationROAD DISC TECHNICAL MANUAL
ROAD DISC TECHNICAL MANUAL INTRODUCTION Congratulations on purchasing a Felt disc brake equipped road bike. As with all of our bikes and components, our aim is to provide the rider with the best product
More informationODOM CLASS SPECIFICATIONS
ODOM CLASS SPECIFICATIONS Effective March 1, 2004 1. GENERAL 1.1 Purpose of the Measurement Rules 1.1.1 The ODOM is a One-Design Class as defined by the American Model Yachting Association (AMYA). However,
More informationPage 1 of 1 04/19/13 SBR
Office of Roadway Engineering - Plan Insert Sheets Number Title Date Number Title Date Number Title Date 201015 Extension of Anchor Bolts 07/20/12 207000 Bikeway Pavement Marking Details 01/18/13 202010
More informationVanguard Sailboats 300 Highpoint Avenue Portsmouth, RI For the dealer nearest you call SAIL
Vanguard Sailboats 300 Highpoint Avenue Portsmouth, RI 02871 For the dealer nearest you call 800. 966.SAIL Unpack the major parts listed below and lay them out on a soft piece of ground free of sharp objects.
More informationStep 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the seam joint is.
WhiplashGV Instruction Manual Email: Brian@Blazermarine.com Phone: 513-598-1769 Step 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the
More informationLITERIDER 2&3 IMPORTANT WARNING. 2Bike (1x) Bolt (1x) Nut (1x) Small Hex Wrench (1x)
LITERIDER 2&3 3 Bike (1x) Bolt (1x) Flat Washer (2x) Nut (1x) Large Hex Wrench (1x) 2Bike (1x) wrench (1x) Small Hex Wrench (1x) keys (2x) Long Strap (1x) 2-Zip Strips (6x) 3-Zip Strips (9x) Wheel strap
More informationConstitution Instructions
Constitution Instructions This kit will build a 1:48 scale hull for the USS Constitution frigate. The kit contains the following parts. 1/8 deck with laser etched deck lines 1/8 railing Ribs Center keel
More informationCantilever Brake. Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike
(English) DM-RCBR001-00 Dealer's Manual ROAD MTB Trekking City Touring/ Comfort Bike URBAN SPORT E-BIKE Cantilever Brake BR-CX70 BR-CX50 BL-4700 BL-4600 BL-R780 BL-R3000 ST-7900 ST-6700 ST-5700 ST-4600
More informationShimano Di2 Installation on S5
Installing Shimano Dura Ace Di2 Shifting Systems Note these instructions and pictures are for assembling the Shimano Dura Ace Di2 system (Internal Spec) on the Cervélo S5 frame. The Shimano Ultegra Di2
More informationASSEMBLY MANUAL HOBIE CATSY
ASSEMBLY MANUAL HOBIE CATSY HOBIE CAT EUROPE ZI Toulon Est, BP 50 8078 Toulon cedex 9, France Tel : + (0)9 08 78 78 - Fax : + (0)9 08 99 Email : hobiecat@hobie-cat.net - http://www.hobie-cat.net ASSEMBLY
More informationPre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender
Pre-Paint>Fuselage>Empennage>Fit vertical tail fin Objectives of this task: To fit the vertical tail fin to the fuselage, including fitting the static probe, static tube, optional strobe light wiring and
More informationShifting Lever. RAPIDFIRE Plus 11-speed
(English) DM-SL0005-04 Shifting Lever Dealer's Manual RAPIDFIRE Plus 11-speed MTB XTR SL-M9000 DEORE XT SL-M8000 CONTENTS IMPORTANT NOTICE... 3 TO ENSURE SAFETY... 4 LIST OF TOOLS TO BE USED... 7 INSTALLATION...
More informationSG36KTL-M Quick Installation Guide. 1 Unpacking and Inspection
SG36KTL-M Quick Installation Guide This guide provides a general instruction of the installation procedures of SG36KTL-M. In no case shall this guide substitute for the user manual or related notes on
More informationInstallation Instructions for Tavan Models TAV-XX-XX
Installation Instructions for Tavan Page 1 of 12 round version square version Instruction page index: Tavan stand-alone installation Tavan joiner installation Tavan L, T or X connector installation Wiring
More informationSpecifications Testing & Adjusting Disassembly & Assembly
SB4191E00 Jul. 2005 Specifications Testing & Adjusting Supplement for Quad Lift Mast D20/25/30/32/33S-3 G/GC20/25/30/32P-3 G/GC20/25/30/32E-3 Important Safety Information Most accidents involving product
More informationRUDDER KIT INSTRUCTIONS
A I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS TARPON 0/40/60/60i The Tarpon series is designed as a high performance sit-on-top kayak tailored for the sport paddler. Our rudder system is designed to
More informationWEIGHT STACK ATTACHMENT. Assembly Manual (888) FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
WEIGHT STACK ATTACHMENT Assembly Manual DF835 (888) 258-0533 FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS
More informationM2 Antenna Systems, Inc. Model No: VLP16
M2 Antenna Systems, Inc. Model No: 100-600VLP16 SPECIFICATIONS: Model... 100-600VLP16 Frequency Range... 100-600 MHz Cont. *Gain... 9.64 dbi Front to back... 12 db Typical Beamwidth... E=64 / H=70 Feed
More informationQUICK START GUIDE CB-450 DATA BUOY PLATFORM
What s Included (1) Buoy hull with data well, 450 lb buoyancy (1) Buoy tower (3) 10W Solar panels (1) Data well lid (isic-cb or pass-through) (3) Top-side lifting eyes (3) Bottom-side mooring eyes (1)
More informationPressure Dump Valve Service Kit for Series 3000 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 000 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00, 400, 500, and 700 applicator
More information275 RID Assembly Instructions
75 RID Assembly Instructions Part No. 0003003 v. Lscsep0 PARTS LIST (Specifications and contents subject to change without notice) Description Part # A. RID Track...0000050 B. Capacity Plate...0053 C.
More informationUSER S MANUAL QUESTIONS? CAUTION. Model No. FMEX Serial No. Write the serial number in the space above for reference. Serial Number Decal
Model No. FMEX81110.0 Serial No. Write the serial number in the space above for reference. USER S MANUAL Serial Number Decal QUESTIONS? If you have questions, or if parts are damaged or missing, please
More informationSoccer Goal. Model: SG20 Series. Installation, Operation and Maintenance Instructions
Soccer Goal Model: SG20 Series Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE
More informationBelow are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project.
Greg Cowens' $10 PVC Roller Reefing for CP-16's by Greg Cowen Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project. Materials: 2
More informationTable of content Introduction 5 1. Part 1. Assembly Tools needed for Assembly Glossary Hulls Mounting the beams 7
Table of content Introduction 5 1. Part 1. Assembly 6 1.1. Tools needed for Assembly 6 1.2. Glossary 6 1.3. Hulls 7 1.3.1. Mounting the beams 7 1.3.2. Fixing the mast rotation cleats 8 1.3.3. Placing the
More informationFitting Instructions for Single Line Mainsail Reefing System For Yachts Up To 9m (30ft) - Part No
Fitting Instructions for Single Line Mainsail Reefing System For Yachts Up To 9m (30ft) - Part No. 41 130 This single line reefing kit allows reefing control lines to be led aft to the safety of the cockpit.
More informationw w w.ro swellmarine. com Part 1 Installation Part # C # C
w w w.ro swellmarine. com Pro Bimini Part 1 Installation Part # C915-119151 # C915-119152 Information: info@roswellmarine.com If you have any questions please call : 1-321-638-1331 REV 16-JUL-18 Moomba
More informationVRS Assembly & Operating Instructions
VRS Assembly & Operating Instructions Models VRS-18 Pn #270003 VRS-24 Pn #270006 VRS-30 Pn #270010 Not for use on pressure vessels equipped with Automatic exhaust valve (680 controls) EMPIRE ABRASIVE EQUIPMENT
More informationRiggers and Associated Parts
Riggers and Associated Parts Pins are all 13mm shafts, with 8x27mm tops, and supplied with washers, nuts and spacers. Rig 1A-sc 13x105mm shaft, 10x55mm base - for scull & sweep Carbon wing S/S yes 28.57
More informationSideshift SS230 Installation on a 2006 Bayliner 265SB
The Sideshift SS230 was packaged very well and all parts were clearly labelled and documented. The overall quality seems far more durable than I expected... I was somewhat concerned that the unit may become
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS KIT CONTENTS: PART NUMBER: DESCRIPTION: E361SXA300 ROOF MOUNT BICYCLE CARRIER B9 TRIBECA Short Carriage Bolt Long Carriage Bolt 3x Over-Molded Wrench Button Head Screw 2x Washer
More informationSTATIONARY TRUCK INTERNAL HALYARD V-CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL INSTALLATION READ ALL INSTRUCTIONS BEFORE PROCEEDING
9390 South 300 West, Sandy, Utah 84070 801-562-0123 800-782-0500 ColonialFlag.com STATIONARY TRUCK INTERNAL HALYARD V-CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL INSTALLATION READ ALL INSTRUCTIONS BEFORE
More informationSG33KTL-M Quick Installation Guide. 1 Unpacking and Inspection
SG33KTL-M Quick Installation Guide This guide provides a general instruction of the installation procedures of SG33KTL-M. In no case shall this guide substitute for the user manual or related notes on
More informationMANITOWOC MODEL TON CAPACITY
LIFTING CHARTS - Crawler Cranes ANITOWOC ODEL - 0 TON CAPACITY BOO RIGGING GUIDE ODEL AND # EL BOO Table of Contents General... Assist Crane Requirements... Accessing Parts... Installation and Removal
More informationFront derailleur. Dealer's Manual FD-M9000 FD-M9020 FD-M9025 FD-M8000 FD-M8020 FD-M8025 FD-M612 FD-M617 FD-M618 FD-M672 FD-M677
(English) DM-FD0003-05 Front derailleur Dealer's Manual FD-M9000 FD-M9020 FD-M9025 FD-M8000 FD-M8020 FD-M8025 FD-M612 FD-M617 FD-M618 FD-M672 FD-M677 CONTENTS IMPORTANT NOTICE... 4 TO ENSURE SAFETY...
More informationINSTALLING YOUR CLC RUDDER
INSTALLING YOUR CLC RUDDER These instructions are written to help you install the CLC rudder kit on your wooden kayak. The rudder can be fitted to your boat during construction or after completion. Please
More informationMaking Spars for the Schooner Jeanette
Making Spars for the Schooner Jeanette..... by Byron Rosenbaum Figure 1. Byron Rosenbaum s 1:16-scale radio-controlled model of the schooner Jeanette. All photographs by the builder. The spars required
More informationSERIES 500 VARIABLE RANGE PNEUMATIC DIFFERENTIAL PRESSURE TRANSMITTER
Man500e 09/2006 Installation Operation and Maintenance Instructions SERIES 500 VARIABLE RANGE PNEUMATIC DIFFERENTIAL PRESSURE TRANSMITTER INDEX 1. INSTALLATION 2. COMPRESSED AIR SUPPLY 3. FLOW MEASURE
More informationRocky Mountain Element Technical Manual. Rev B
Rocky Mountain Element Technical Manual Rev B 1 Table of Contents Materials Required... 3 Suspension Pivot Torque Guide... 4 Small Parts Torque Guide... 5 Assembly Instructions... 6 1) Bearing Installation...
More informationINSTALLATION INSTRUCTIONS
KIT CONTENTS: INSTALLATION INSTRUCTIONS PART NUMBER: DESCRIPTION: E361SXA302 roof MOUNT BICycle CARRIER SINGLE Short Carriage Bolt 1x Long Carriage Bolt 3x Over-Molded Wrench 1x Button Head Screw 2x Washer
More informationUSER MANUAL. you pedal, something amazing happens
TM USER MANUAL you pedal, something amazing happens THANK YOU! In our humble beginnings we ran a bike-powered smoothie booth at Northern California music festivals called The Juice Pedaler. We saw the
More informationE-trike Li Assembly Guide
PREPARATION 1. Read this assembly manual BEFORE commencing assembly. 2. Carefully remove all the components and packaged hardware from the shipping boxes. 3. Unpack the contents of the large double box
More informationHALYARD EXITS, CLEATS, CLUTCHES, WINCH PADS, HANDLE POCKET
HALYARD EXITS, CLEATS, CLUTCHES, WINCH PADS, HANDLE POCKET 1(6) General CNC-milled masts Cut out using templates Cut out without using templates Assembly Assembly clutch spinnlock ZS/1214 Check point General
More informationSide-of-Pole Mount for 1 Module (SPM1) For Module Types A & B
Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 080311-2 SP3363-1 Side-of-Pole Mount for 1 Module (SPM1)
More informationSETTING UP THE MODEL 210B SRA
SETTING UP THE MODEL 210B SRA SAFETY PRECAUTIONS FOR THE MODEL 210B SRA System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris: During
More informationCarbo Racing Foil Instruction Manual Unit 0, 1, 2, 3
Carbo Racing Foil Instruction Manual Unit 0, 1, 2, 3 WARNING!: Strictly follow all instructions to avoid an accident, damage to your vessel, personal injury or death. See www.harken.com/manuals for additional
More informationKari-Tek. Kari-Tek. Hydro Skeg Retro-Fitting Instructions. Instructions for retro-fitting of Hydro Skeg
Kari-Tek Instructions for retro-fitting of Hydro Skeg A good knowledge of fibreglassing will be required to fit the Hydro Skeg successfully. When working with fibreglass and cutting the holes, safety glasses,
More information830 SureFlo Soap Systems Installation Instructions. Foam Soap Cabinet... Pages 2-9 Liquid Soap Cabinet... Pages 10-19
830 SureFlo Soap Systems Installation Instructions Foam Soap Cabinet... Pages 2-9 Liquid Soap Cabinet... Pages 10-19 INSTALLATION INSTRUCTIONS SureFlo SOAP DISPENSING SYSTEM FOAM VERSION ONLY B-830 Foam
More informationIn each step, the needed parts are shown the number right below. Locate all parts for the step.
Tools Required for Assembly Phillips Screwdriver, Med Needle Nose Pliers Sandpaper (#400 grit) Hobby Knife Scissors CA Instant Glue Rubbing Alcohol Drill Bit 1/16", 1.6mm 5/64, 2mm 1/8, 3mm 5/32, 4mm Before
More informationPressure Dump Valve Service Kit for Series 2300 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit
More informationHOME ASSEMBLY INSTRUCTIONS
HOME ASSEMBLY INSTRUCTIONS This Papillionaire Bicycle now belongs to you. It will take you to work, wait patiently outside your local cafe, and carry your groceries home. This is the start of your long-term
More informationInstallation Instructions for your Winter Storage Cover
Installation Instructions for your Winter Storage Cover QUINTE CANVAS MANUFACTURING 1120 CLYDE COURT, KINGSTON, ONTARIO K7P 2E4 (613) 384-6316 (613) 384-0002 Fax topshop@kos.net www.topshop.on.ca Before
More informationChapter 9 Accessories
SuperLite 17B Chapter 9 Accessories 9.1 Introduction This section provides the manufacturer s advice on how to install KMDSI accessories including the Hot Water Shroud, Low Pressure Inflator Hoses, and
More informationInstallation Instructions for Reef-Rite Furling Systems
Installation Instructions for Reef-Rite Furling Systems Congratulations on the purchase of your new Reef-Rite Furling System! It has been constructed with great care from the finest materials available,
More informationPanoptix PS51-TH FrontVü/LiveVü Thruhull
Panoptix PS51-TH FrontVü/LiveVü Thruhull Transducer Installation Instructions Important Safety Information WARNING See the Important Safety and Product Information guide in the chartplotter or fishfinder
More informationHoldUp Plus2. Safety Kit included: See additional instructions for installation. REAR WHEEL TRAY. BASE (1x) lock WASHER (1x) KEY (2x) SAFETY CLIP (1x)
HoldUp Plus2 InsTAll This product on 2" hitch version of the HoldUp Front WHEEL TRAY assembly (1x) REAR WHEEL TRAY assembly (1x) wrench (1x) BASE (1x) bolt (8X) Lock WASHER (8X) Washer (8x) KEY (2x) SAFETY
More informationTo Purchase This Item, Visit BMI Gaming (800)
How to play the game How to play the game The object of the game is to reach the Game Goal before your opponent. HOW TO START: - A coin toss decides who starts the game. The winner of the coin toss also
More informationDinghy Racers Parts List
Parts List Thank you for your purchase of our Dinghy Racer whirligig set. Please check this list before assembly of your new Dinghy Racer set to make sure that you have all of the parts listed. 1-Yellow
More informationATOC Meteorological Tower (6 meter-4 level) Guide
ATOC Meteorological Tower (6 meter-4 level) Guide SETUP Outline 1. Siting 2. Components 3. Transportation 4. The Tower 5. The Cables and Data Logger Siting Selecting an appropriate site for the weather
More informationRudder Kit Assembly Instructions for Quest 13
Rudder Kit Assembly Instructions for Quest 13 Revised 4/2/2015 78501 Rudder System The Hobie Quest is designed for the addition of an optional rudder system. Rudder systems in boats like this allow you
More informationGel Drop Seal for FOSC 450 Fiber Optic Splice Enclosure Installation Instructions
Gel Drop Seal for FOSC 450 Fiber Optic Splice Enclosure Installation Instructions TECP-30-215 Issue 1 4/2013 INTRODUCTION The Gel Drop Seal device is for use with FOSC 450 B, B Short, C, and D size closures
More informationFDR CHRYSLER 16' CATAMARAN (MUSKETEER) The initial rigging of a sailboat is not difficult, but if the boat is strange
Page of 6 Revised 2/0/76 RIGGING INSTRUCTIONS FDR CHRYSLER 6' CATAMARAN (MUSKETEER) The initial rigging of a sailboat is not difficult, but if the boat is strange to the new owner, or the new owner is
More informationCABLE GLANDS. Connector~Tech Providing Harsh Environment Connector SOLUTIONS
Connector~Tech www.connectortech.com.au Providing arsh Environment Connector SOLUTIONS CABLE ANDS Connector~Tech is a Division of: Colourview Electronics (QLD) Pty Ltd (ABN 99 065 191 424) Unit 2, 8 Colebard
More informationAssembly Guide ST200 FUNCTIONAL TRAINER
Assembly Guide ST200 FUNCTIONAL TRAINER Assembly Guide ST200 FUNCTIONAL TRAINER To avoid possible damage to this Functional Trainer, please follow these assembly steps in the correct order. Before proceeding,
More informationi NOTE: This installation manual contains important information related to system
TRx Pivot Plus Manual Elevating Legrests (ELR) Installation and Set-Up Manual i NOTE: This installation manual contains important information related to system set-up and adjustments. Please forward to
More informationBeach Dolly with cradle & keel pad Assembly Instructions
Beach Dolly with cradle & keel pad Assembly Instructions H G B A D C I J L F PART NAME QTY A. AXLE... 1 with tongue bracket and cradle supports attached B. CRADLE SUPPORT BAR... 2 C. TONGUE... 1 D. TONGUE
More information