OBSOLETE DESIGN DATA. CONCENTRATE CONTROLLERS 2, 3", 4", 6" and 8" (50, 80, 100, 150, and 200 mm)
|
|
- Kathlyn Perkins
- 5 years ago
- Views:
Transcription
1 March 1, 2001 Foam 210 a 1. PRO DUCT NAME Viking Concentrate Controller 2,, (102 mm) (152 mm), (203 mm) Available since MANUFACTURED FOR THE VIKING COR PO RA TION 210 North Industrial Park Road Hastings, MI U.S.A. Telephone: (616) (877) Fax: (616) PRO DUCT DE SCRIP TION The Viking concentrate controllers accurately proportion foam con cen - trate into a water stream over a wide range of wa ter flow rates. The con - trollers proportion foam at con cen - trations from 1% to 3 %. 4. TECHNICAL DATA The Viking concentrate controllers are tested as part of a fire ex tin guish - ing system and are UL Listed and FM Approved for use with designated foam concentrates, bladder tanks, piping configurations and discharge devices. 5. OP ER A TION The Vi king concentrate controller is a modified venturi device. As water flows through the venturi, it creates an area of lower pressure referred to as the metering pressure drop. As the water flow increases through the venturi, the metering pressure drop increases, allowing more foam con - centrate to enter through the orifice. A decrease in the wa ter flow reduces the metering pressure drop, thereby reducing the foam concentrate flow. Because the foam concentrate flow varies in direct proportion to the wa - ter flow, the concentrate controller can accurately proportion foam over a wide range of wa ter flow rates. The flow rate at which the metering pressure drop is just high enough to overcome the pressure losses through the piping and the bladder tank is called the low flow rating. The flow rate through the controller must Form No. F_ DESIGN DATA be at or above it s low flow rating in order to properly proportion foam. A good rule to follow to ensure the piping is designed properly follows: The combined total equivalent length (pipe length plus equivalent lengths for fittings and valves) of the water supply inlet piping and the foam concentrate discharge piping should not exceed 50 equivalent feet (15,2 m). The diameter of this piping must be the same size as the foam liquid inlet to the concentrate con trol - ler. If the total equivalent length must exceed 50 feet (15,2 m), then re fer to the Proportioning Device Design data located in the Design section of this data book for the method of calculating these pipe sizes. 6. AP PLI CA TION The Vi king concentrate controllers are part of a foam system. In addition to the controller, the main com po - nents of the foam sys tem are foam concentrate, a foam stor age tank, a water supply, piping, and discharge devices. The discharge devices most commonly used are sprin klers, nozzles, and foam chambers. The system must be designed so that the concentrate controller can ac cu - rately proportion foam over the range of flow rates expected during the sys tem operation. 7. AVAILABILITY AND SERVICE The Vi king concentrate controllers are available through a network of domestic, Canadian and in ter na - tional dis trib u tors. See the Yellow Pages of the telephone directory for a local distributor (listed under Sprin- kler-automatic-fire ), or contact The Viking Corporation. Vi king tech ni cal data may be found on The Vi king Cor po ra tion s Web site at http :// The Web site may in clude a more recent edi tion of this tech ni cal data page. 8. GUAR AN TEES For details of warranty, re fer to Vi - king s current list price schedule or contact Viking directly. CONTROLLERS 2,,, and (50, 80, 100, 150, and 200 mm) 9. IN STAL LA TION DO NOT ALTER THE PIPING WITH - OUT CONSULTING A SYSTEM DESIGN REPRESENTATIVE. BE - FORE INSTALLING A CON CEN - TRATE CONTROLLER, CHECK THE SYSTEM DESIGN DRAWING TO EN - SURE THE CONTROLLER LO CA - TION DOES NOT CREATE EX CES - SIVE HEAD PRESSURE OR FRIC - TIONAL LOSSES. The controller must be installed with the ar row pointing in the direction of the wa ter flow. Straight piping equal to four (4) to six (6) pipe diameters should be installed both before and after the concentrate controller to en - sure proportioning accuracy. The ideal location for the controller is level or below the top discharge and within 3 feet (1 m) of the tank. The controller can be placed further from the tank, if the pressure drop through the blad der tank does not exceed the metering pressure drop. The pres - sure drop within the piping can be minimized by: 1. Minimizing the number of tees and elbows. 2. Minimizing the distance from the bladder tank to the controller, using full port valves. 3. Increasing the pipe diameter. Viking strongly advises the in stal la - tion of a concentrate control valve, and swing check valve between the bladder tank and concentrate con - troller. This will prevent migration of water into the bladder tank. Viking does not furnish piping with the concentrate controllers. It is the responsibility of the system design engineer to determine the ap pro pri - ate piping. 10. INSPECTIONS AND TESTS Refer to the applicable Viking foam system technical data pages for in - structions on inspections and test ing of the complete foam system. 11. MAIN TE NANCE Refer to the applicable Viking foam system technical data pages for in - structions on maintenance of the complete system. Replaces page 860 a-f, dated March 25, Re - placed 3M reference with National Foam, added drawings and revised page number.
2 210 b March 1, 2001 CON TROL LERS 2 Threaded Concentrate Controller SIZE A B C D E F G WEIGHT Threaded Grooved 2 7/ (73) 3 3/1 (81,0 mm) 3 31/3 (101,2 mm) 4 1/ (114,3 mm) 9" (228,6 mm) 9" (228,6 mm) 6 1/ (165,1 mm) 6 1/ (165,1 mm) 10" (254 mm) 10" (254 mm) 12 3/ (323,9 mm) 12 3/ (323,9 mm) 13 1/ (342,9 mm) 13 1/ (342,9 mm) 3 1/ (79,4 mm) 3 1/ (79,4 mm) (76,2 mm) (76,2 mm) 3 1/ (88,9 mm) (101,6 mm) 4 5/ (117,5 mm) 6 3/ (161,9 mm) 1" (25,4 mm) 1" (25,4 mm) 1 1/ (32 mm) 1 1/ (38,1 mm) 1 1/ (38,1 mm) 2 1/ (63,5 mm) 2 1/ (63,5 mm) x 7 1/ (76 mm x 190 mm) x 7 1/ (76 mm x 190 mm) x 9" (102 mm x 228 mm) x 9" (102 mm x 228 mm) x 11" (152 mm x 297 mm) x 11" (152 mm x 297 mm) x 13 1/ (203 mm x 343 mm) x 13 1/ (203 mm x 343 mm) 2 Grooved Concentrate Controller 2 1/ (57,1 mm) 2 1/ (57,1 mm) 1 1/ (38,1 mm) (76,2 mm) 3 23/6 (59,9 mm) 3 1/1 (77,8 mm) 2 1/ (63,5 mm) 3 1/ (88,9 mm) 5 lbs. (2.3 kg.) 5 lbs. (2.3 kg.) 12 lbs. (5.4 kg.) 23 lbs. (10.4 kg.) 19 lbs. (8,6 kg.) 35 lbs. (15.9 kg.) 34 lbs. (15.4 kg.) 55 lbs. (25 kg.) 54 lbs. (24 kg.) 85 lbs. (38.6 kg.) Dimensions in parentheses are metric and may vary from actual.
3 March 1, 2001 CON TROL LERS 210 c 6 Style Concentrate Controller (3, 4 & 8 also available) 6 Style Concentrate Controller (3, 4 & 8 also available)
4 210 d March 1, 2001 DESIGN DATA CONTROLLERS 2,,, and (50, 80, 100, 150, and 200 mm) BLADDER TANK AND CONTROLLER PERFORMANCE Controller Size Threaded 1" NPT Grooved 1" NPT 1-1/ NPT 1-1/ NPT 1-1/ NPT NPT NPT 2-1/ NPT 2-1/ NPT NPT Viking Concentrate National Viking Part No. Viking Controller Model No. Orifice dia. Min. Flow Max. Flow Inch (mm) gpm (L/m) gpm (L/m) VF1NWAFFF Aer-o-Water 1% F02045A VT-2AN.106 (2,7) 30 (113) 175 (662) VF3NLAFFF Aer-o-Lite 3% F02045B VT-2BN.205 (5,2) 27 (102) 231 (874) VF3NWAFFF-MS Aer-o-Water 3% EM F02045C VT-2CN.205 (5,2) 25 (95) 255 (965) SUPREME3G-ARC Universal Gold 3% F02045J VT-2JN.228 (5,8) 60 (227) 187 (708) VF1NWAFFF Aer-o-Water 1% F02044A VG-2AN.106 (2,7) 30 (113) 175 (662) VF3NLAFFF Aer-o-Lite 3% F02044B VG-2BN.205 (5,2) 27 (102) 231 (874) VF3NWAFFF-MS Aer-o-Water 3% EM F02044C VG-2CN.205 (5,2) 25 (95) 255 (965) SUPREME3G-ARC Universal Gold 3% F02044J VG-2JN.228 (5,8) 60 (227) 187 (708) VF1NWAFFF Aer-o-Water 1% F02050A VW-3AN.201 (5,1) 75 (284) 700 (2 650) VF3NLAFFF Aer-o-Lite 3% F02050B VW-3BN.300 (7,6) 30 (113) 600 (2 271) VF3NWAFFF-MS Aer-o-Water 3% EM F02050C VW-3CN.300 (7,6) 30 (113) 550 (2 082) SUPREME3G-ARC Universal Gold 3% F02050J VW-3JN.350 (8,9) 200 (757) 700 (2 650) VF1NWAFFF Aer-o-Water 1% F02046A VF-3AN.201 (5,1) 75 (284) 700 (2 650) VF3NLAFFF Aer-o-Lite 3% F02046B VF-3BN.300 (7,6) 30 (113) 600 (2 271) VF3NWAFFF-MS Aer-o-Water 3% EM F02046C VF-3CN.300 (7,6) 30 (113) 550 (2 082) SUPREME3G-ARC Universal Gold 3% F02046J VF-3JN.350 (8,9) 200 (757) 700 (2 650) VF1NWAFFF Aer-o-Water 1% F02051A VW-4AN.281 (7,1) 150 (568) 1200 (4 542) VF3NLAFFF Aer-o-Lite 3% F02051B VW-4BN.430 (10,9) 60 (227) 1300 (4 921) VF3NWAFFF-MS Aer-o-Water 3% EM F02051C VW-4CN.430 (10,9) 60 (227) 1300 (4 921) SUPREME3G-ARC Universal Gold 3% F02051J VW-4JN.455 (11,5) 400 (1 514) 1370 (5 186) VF1NWAFFF Aer-o-Water 1% F02047A VF-4AN.281 (7,1) 150 (568) 1200 (4 542) VF3NLAFFF Aer-o-Lite 3% F02047B VF-4BN.430 (10,9) 60 (227) 1300 (4 921) VF3NWAFFF-MS Aer-o-Water 3% EM F02047C VF-4CN.430 (10,9) 60 (227) 1300 (4 921) SUPREME3G-ARC Universal Gold 3% F02047J VF-4JN.455 (11,5) 400 (1 514) 1370 (5 186) VF1NWAFFF Aer-o-Water 1% F02052A VW-6AN.406 (10,3) 400 (1 514) 2600 (9 842) VF3NLAFFF Aer-o-Lite 3% F02052B VW-6BN.703 (17,8) 60 (227) 2750 (10 410) VF3NWAFFF-MS Aer-o-Water 3% EM F02052C VW-6CN.703 (17,8) 100 (378) 3000 (11 356) SUPREME3G-ARC Universal Gold 3% F02052J VW-6JN.803 (20,4) 675 (2 555) 3000 (11 356) VF1NWAFFF Aer-o-Water 1% F02048A VF-6AN.406 (10,3) 400 (1 514) 2600 (9 842) VF3NLAFFF Aer-o-Lite 3% F02048B VF-6BN.703 (17,8) 60 (227) 2750 (10 410) VF3NWAFFF-MS Aer-o-Water 3% EM F02048C VF-6CN.703 (17,8) 100 (378) 3000 (11 356) SUPREME3G-ARC Universal Gold 3% F02048J VF-6JN.803 (20,4) 675 (2 555) 3000 (11 356) VF1NWAFFF Aer-o-Water 1% F02053A VW-8AN.563 (14,3) 750 (2 839) 4000 (15 142) VF3NLAFFF Aer-o-Lite 3% F02053B VW-8BN 1.0 (25,4) 200 (757) 3900 (14 763) VF3NWAFFF-MS Aer-o-Water 3% EM F02053C VW-8CN 1.0 (25,4) 200 (757) 4000 (15 142) SUPREME3G-ARC Universal Gold 3% F02053J VW-8JN 1.3 (33,0) 1300 (4 921) 4000 (15 142) VF1NWAFFF Aer-o-Water 1% F02049A VF-8AN.563 (14,3) 750 (2 839) 4000 (15 142) VF3NLAFFF Aer-o-Lite 3% F02049B VF-8BN 1.0 (25,4) 200 (757) 3900 (14 763) VF3NWAFFF-MS Aer-o-Water 3% EM F02049C VF-8CN 1.0 (25,4) 200 (757) 4000 (15 142) SUPREME3G-ARC Universal Gold 3% F02049J VF-8JN 1.3 (33,0) 1300 (4 921) 4000 (15 142)
5 March 1, e ME TERING PRES SURE DROP vs. FLOW RATE
6 210 f March 1, 2001 PER MA NENT PRES SURE LOSS vs. FLOW RATE Replaces page 860 a-f, dated March 25, Re - placed 3M reference with National Foam, added drawings and revised page number. Form No. F_041497
FM Approved - Automatic Water Control Valve as standard deluge valve. No formal approval available for coating. Foam Concentrate
December 6, 2010 Foam 31a 1. Description With Multiple Pilot Pressure Regulating Foam/Water Deluge Systems Supplied by a Bladder Tank, multiple pilot pressure regulating foam risers can be supplied from
More informationFM Approved - Automatic Water Control Valve as standard deluge valve. No formal approval available for coating. Foam Concentrate
December 6, 2010 Foam 21a 1. Description With Multiple Foam/Water Deluge Systems Supplied by a Bladder Tank, multiple deluge foam risers can be supplied from a single foam concentrate source. Where a bladder
More informationTECHNICAL DATA NOTICE
Page 1 of 5 1. DESCRIPTION FomTec BFZ Inductors are used to mix foam concentrate with water when the foam concentrate is supplied from a tank at atmospheric pressure. The BFZ inductor can be installed
More informationWet pipe low flow foam/water system
December 6, 2010 Foam 14a 1. The Viking Low Flow Foam/Water proportioning system, is a UL Listed and FM Approved system, for use with Viking supplied foam concentrates. This system consists of a standard
More informationOBSOLETE. Wet pipe low flow manifold system
June 1, 2008 Foam 15a 1. Description Multiple risers can be supplied from a single proportioning device. A riser manifold is installed with various riser types and sizes that are to supply foam solution
More informationLINE PROPORTIONERS LP NPR260 Approvals: UL, ULC
Approvals: UL, ULC Simple Inexpensive & Accurate Foam Proportioning Inlet Pressure Choices 90-200 PSI Flow Rate 44-578 GPM Special Designs Available Flow & Pressure Salt Water Compatible Description National
More informationTECHNICAL DATA. the Viking Pilot Pressure Regulating Valve 1 Model A-1 Speed Control Assembly: OBSOLETE. the Viking Speed Control Assembly 1
November 30, 1994 534 a 1. PRODUCT NAME VIKING 2" (50mm), 3" (75mm), 4" (100mm), 6" (150mm) 2. MANUFACTURER THE VIKING CORPORATION 210 N. Industrial Park Road Hastings, Michigan 49058 U.S.A. Telephone:
More informationOBSOLETE DESIGN DATA FOAM MAKER APPLICATION
Foam 410 a 1. DESCRIPTION Foam makers are in-line foam dis - charge devices. Foam makers are utilized in hazards where enhanced foam qualities are needed to protect a hazard. Foam makers are gen er - ally
More informationFoam Mixers & Proportioning Systems
Foam Mixers & Proportioning turer ms turer ms turer ms turer ms turer ms turer ms turer ms turer ms turer ms turer ms turer ms turer ms turer ms turer ms turer ms turer ms turer turer ms turer ms turer
More informationPipe Thread Connection 1/2 inch NPT. Friction Loss Refer to Figure 3
Worldwide Contacts www.tyco-fire.com Model B-1 Pipe Line Strainer General Description The Model B-1 Pipe Line Strainers (Ref. Figures 1 and 2) are designed for installation in the water supply connection
More informationTECHNICAL DATA OBSOLETE
August 2, 2006 Foam 70a 1. DESCRIPTION A Hi-Expansion Foam System is a standard deluge system capable of discharging a foam/water solution automatically through open Hi-Ex Generators. A Hi-Expansion Foam
More informationTECHNICAL DATA Q= C. Table 1 - Specifications
September 25, 2013 Pressure Regulation 537a 1. Description The Model B-3 Pilot Operated Pressure Control Valve is a factory assembled unit. The unit consists of a Model J-2 Halar coated Flow Control Valve,
More informationTECHNICAL DATA. than the water inlet pressure to the concentrate
Foam102a 1. DESCRIPTION The Viking Low Flow Foam/Water proportioning system, is a UL Listed and FM Approved system, for use with 3M foam concentrates. This system consists of a standard wet pipe sprinkler
More informationData Sheet Issue A
Features 1. Differential latching clappertype, lighweight, dependable construction. 2. Low Air Pressurized System, 8 psi -to- 26 psi (0,6 bar to- 1,8 bar) 3. Reset externally. Cover removal is not required.
More informationTECHNICAL DATA. Pressure Regulation 531a. April 24, 2009
April 24, 29 Pressure Regulation 531a 1. DESCRIPTION The Viking Regulating Valve is a direct-acting, single-seated, spring-loaded diaphragm valve. When installed as a pilot regulating valve on a Viking
More informationTECHNICAL DATA. Page 1 of 12
Page 1 of 12 1. DESCRIPTION The Viking Regulating Valve is a direct-acting, single-seated, spring-loaded diaphragm valve. When installed as a pilot regulating valve on a Viking Model H or J Flow Control
More informationAnti-flood device Model B-1
December 4, 2009 Dry Systems 123a 1. DESCRIPTION The Anti-flood Device is required when Viking accelerators are installed on dry systems according to Viking Model E-1 Accelerator Trim Charts. In the SET
More informationVERTICAL BLADDER TANK
Balanced Pressure Proportioning System Reliable Foam System Requiring Only Water Power Perfect For Tight Spaces UL Listed, ASME, National Board Registered Bladder-UL162 Approved, High Tensile Pressure
More informationSpeed control assembly model A-1
Pressure Regulation 533a 1. DESCRIPTION The Viking Speed Control Assembly provides adjustment of the opening speed of Viking Deluge Valves, and adjustment of both the opening and closing speed of Viking
More informationTECHNICAL DATA. Deluge Valves 211a. November 30, 2007 DELUGE VALVE MODEL E-1 ANGLE STYLE 3 (DN80), 4 (DN100) & 6 (DN150)
November 30, 2007 Deluge Valves 211a DESCRIPTION The Viking Model E-1 Deluge Valve is a quick-opening, differential diaphragm, fl ood valve with one moving mechanism. The deluge valve is used to control
More informationHORIZONTAL BLADDER TANK
Balanced Pressure Proportioning System Reliable Foam System Requiring Only Water Power Perfect For Low Ceilings UL Listed, ASME, National Board Registered Bladder-UL162 Approved, High Tensile Pressure
More informationTECHNICAL DATA ANTI-FLOOD DEVICE MODEL B-1 1. DESCRIPTION
Page 1 of 6 1. DESCRIPTION The Model B-1 Anti-flood Device is required when Viking accelerators are installed on dry systems according to Viking Model E-1 Accelerator Trim Charts. In the SET condition,
More informationEnd Connection. Thread x Thread N/A N/A N/A N/A Flange x Flange N/A
Worldwide Contacts www.tyco-fire.com Model RV-1 Pressure Relief Valve, Pilot-Operated, Globe and Angle Body Styles General Description Valves, through inch (DN50 through DN00), are factory assembled and
More informationSEMI FIXED/PORTABLE LINE PROPORTIONERS SLP NPR270
SEMI FIXED/PORTABLE LINE PROPORTIONERS SLP Simple Inexpensive Foam Proportioner Portable Inlet Pressure Choices 90 to 200 PSI Foam Rate 44 GPM to 362 GPM Salt Water Compatible Special Flow And Pressure
More informationTECHNICAL DATA. Table 1 - Specifications
Page 1 of 6 1. DESCRIPTION Model A-3 Pilot Operated Pressure Control Valves are factory assembled units. Each unit consists of a Model H-2 Halar coated Flow Control Valve, a Speed Control Valve, a Model
More informationTECHNICAL DATA. Low-Flow Foam Preaction System with Hydraulically Actuated Concentrate Control Valve.
Foam 302 a 1. DESCRIPTION (Refer to Figure 1 on page 302 e.) The Viking Low-Flow Foam/Water Proportioning System is a UL Listed and FM Approved system, for use with 3M and Viking brand foam concentrate.
More informationDESIGN DATA OBSOLETE. C. Inspections - It is imperative that the system be inspected and tested on a regular basis. See Inspection
February 9, 1998 Foam 201a 1. DESCRIPTION A Deluge Bladder Tank Foam/Water System is a standard deluge system capable of discharging a foam/water solution automatically through open sprinklers, spray nozzles,
More informationTECHNICAL DATA. Q = C v P S
January 6, 2012 Preaction 347a 1. Description Viking supervised Double-Interlocked Electric/Pneumatic Release Preaction Systems utilize the Viking G-6000P Valve. The small profile, lightweight, pilot operated
More informationMANUAL FLOW CONTROL 2-1/2" - 18" QUICKSET FLOW CHART
This chart performs two functions: It allows you to calculate the permanent pressure drop for any size Quickset or. This figure is useful mostly in the design process, for system calculations. It allows
More informationSABERINDO PACIF SABERINDO PACIFIC CIFIC SABERINDO PA. A Tyco International Company
CIF A Tyco International Company 1 Foam Concentrate CIF 3% AFFF -UL Listed -UL Canada Listed 6% AFFF 6 parts AFFF concentrate to 94 parts water -UL Listed- Foam Liquid -UL Canada Listed 3% FLUOROPROTEIN
More informationTECHNICAL DATA. Trimpac 244a. September 16, 2013
September 16, 2013 Trimpac 244a 1. DEsCrIpTION DESCRIPTION TRIMPAC Model B-1 and B-1B is a factory-assembled trim package with an electric release module in a metal enclosure. The standard trim normally
More informationTECHNICAL DATA. Q = C v P S
January 6, 2012 Preaction 333a 1. Description Viking supervised Surefire Preaction Systems Utilize the Viking G-3000P Valve. The small profile, lightweight, pilot-operated Viking G-3000P Valve comes complete
More informationModel DDX-LP Dry Pipe Valve System 8 (200mm) Features. Differential latching clapper-type, lighweight, dependable construction.
Bulletin 335 Model DDX-LP Dry Pipe Valve System 8 (200mm) Bulletin 335 Features 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Differential latching clapper-type, lighweight, dependable construction. Low Air Pressurized
More informationFeatures. Model DDX-LP Dry Pipe Valve System 4 (100mm), 6 (150mm) & 165mm Sizes
Bulletin 357 Rev. E Model DDX-LP Dry Pipe Valve System 4 (100mm), 6 (150mm) & 165mm Sizes Bulletin 357 Rev. E Features 1. 2. 3. 4. 5. 6. 7. 8. 9. Differential-type valve, lightweight, dependable construction.
More informationTECHNICAL DATA. Q = C v P S
January 6, 2012 Preaction 348a 1. Description Viking supervised Surefire Preaction Systems utilize the Viking G-6000P Valve. The small profile, lightweight, pilot operated Viking G-6000P Valve comes complete
More informationDESIGN DATA A WET PIPE BLADDER TANK FOAM/WATER SYSTEM WITH HYDRAULICALLY ACTUATED DELUGE CONCENTRATE CONTROL VALVE
February 9, 1998 Foam 101a A BLADDER TANK WITH 1. DESCRIPTION A Wet Pipe Bladder Tank Foam/Water System is a standard wet pipe automatic sprinkler system capable of discharging a foam/water solution automatically
More informationTECHNICAL DATA OBSOLETE
April 9, 2009 Preaction 326a 1. DESCRIPTION Viking supervised Double-Interlocked Electric/Pneumatic Release Preaction Systems utilizing the Viking G-4000P Deluge Valve. The small profi le, lightweight,
More informationTECHNICAL DATA. Q = C v P S
Preaction 346a 1. Description The 6 Model G-6000P Electric Release Preaction System Riser Assembly can be used as a Single Interlock Preaction System with Electric Release, or as a Double Interlock Preaction
More informationGauge Adapters. Senior 2 1 2" [63,5] Bolt Circle Adapt ers. 22 Series ISO 9001:2008 CERTIFIED. Low pressure applications. The Measure of Excellence
Gauge Adapters 22 Series ISO 900:2008 CERTIFIED General Information* The riser height or H dimension is measured from the outside of the tank shell to the face of the adapt er where the gauge attaches.
More informationTECHNICAL DATA. Dry 132a. October 1, 2008
October 1, 2008 Dry 132a 1. Description Viking High Pressure (HP) Dry Systems utilize a Viking Model E or Model F Deluge Valve to control the water supply to system piping equipped with closed sprinklers.
More informationTECHNICAL DATA CAUTION
Page 1 of 12 1. DESCRIPTION The Viking Model C-2 Pilot Pressure Regulating Valve is a direct-acting, single-seated, spring-loaded diaphragm valve. When installed as a pilot regulating valve on a Viking
More informationOBSOLETE DESIGN DATA. Foam 301a. February 9, 1998
February 9, 1998 Foam 301a A BLADDE TANK WITH HYDAULICALLY ACTUATED DELUGE CONCENTATE CONTOL VALVE 1. DESCIPTION A Preaction Bladder Tank Foam/Water System is a standard preaction system capable of discharging
More informationTECHNICAL DATA. Q = C v P S
January 6, 2012 Preaction 331a 1. Description Viking supervised Double-Interlocked Electric/Pneumatic Release Preaction Systems utilize the Viking G-3000P Valve. The small profile, lightweight, pilot-operated
More informationTECHNICAL DATA. Deluge Valves 218a. November 30, 2007 DELUGE VALVE MODEL F-1 STRAIGHT THROUGH STYLE 2-1/2 (DN65) - 8 (DN200)
November 30, 2007 Deluge Valves 218a DESCRIPTION The Viking Model F-1 Deluge Valve is a quick opening, differential diaphragm and fl ood valve with one moving mechanism. The Deluge Valve is used to control
More informationTECHNICAL DATA. Trimpac 251a. Spetember 16, 2013
Spetember 16, 2013 Trimpac 251a 1. DEsCrIpTION DESCRIPTION TRIMPAC Model B-6 and B-6B is a factory assembled trim package for a double interlocked preaction system with an electric/pneu-lectric release
More informationTECHNICAL DATA. Trimpac 256a. October 31, 2013
October 31, 2013 Trimpac 256a 1. DESCRIPTION The Viking SUREFIRE SIngle Interlock Preaction TRIMPAC Model D-1 and D- 1B used with either a Model E or F Deluge Valve (A.1), a Viking Easy Riser check valve
More informationDAV - WP DAV - WP. Wastewater Air Valves. Product Catalogue. (Wastewater Air Valves) DAV - WP
DAV - WP Wastewater Air Valves DAV - WP (Wastewater Air Valves) Product Catalogue DAV - WP DAV Series??? DAV-WP General DAV-WP Wastewater Air Valves The DAV-WP valve has been designed for efficient discharge
More informationTECHNICAL DATA OBSOLETE
June 1, 2008 Foam 240a 1. DESCRIPTION The Chemguard Bladder Tank is one component in a balanced pressure foam proportioning system. It requires no external power, other than the water pressure to ensure
More informationAir Eliminators and Combination Air Eliminators Strainers
Description Air Eliminators and Combination Air Eliminator Strainers are designed to provide separation, elimination and prevention of air in piping systems for a variety of installations and conditions.
More informationBalancing HVAC Hydronic Systems Part 3: Flow Measurement Valves
Balancing HVAC Hydronic Systems Part 3: Flow Measurement Valves Monday Morning Minutes by Norm Hall, August 20, 2018 The flow balance of a hydronic system is a critical component in the commissioning of
More informationHorizontal Bladder Tanks
DATA SHEET Horizontal Bladder Tanks Features UL Listed and FM Approved for use with various ANSUL proportioners and foam concentrates 175 psi (12.1 bar) maximum allowable working pressure (design pressure)
More informationModel B-1 Pipe Line Strainer 3, 4, 6 & 8 Inch (DN80, DN100, DN150 & DN200) 175 psi (12,1 bar) General Description. Technical Data
Technical Services: Tel: (800) 381-312 / Fax: (800) 71-5500 Customer Service/Sales: Tel: (215) 362-0700 / (800) 523-6512 Fax: (215) 362-5385 Model B-1 Pipe Line Strainer 3,, 6 & 8 Inch (DN80, DN100, DN150
More informationAIR FOAM CHAMBER DATA SHEET
FIRE FIGHTING EQUIPMENT DATA SHEET AIR FOAM CHAMBER DATA SHEET JOB NO. : RFQ. NO. : ISSUE : SHEET OF 01 CUSTOMER : ITEM NO. : 02 PROJECT : QUANTITY : 03 LOCATION : SERVICE : FOAM SYSTEM 04 05 CODE & STANDARDS
More informationModel MTB-ASME Horizontal Bladder Tanks
DATA SHEET Model MTB-ASME Horizontal Bladder Tanks Features n UL Listed and FM Approved for use with various proportioners and foam concentrates n 175 psi (12.1 bar) maximum allowable working pressure
More informationTECHNICAL DATA. TRIMPAC Model B-5 & B-5B
September 16, 2013 Trimpac 250a 1. DESCRIPTION DEsCRIPTIoN is a factory assembled trim package for a ed an electric/pneumatic release module in a metal enclosure. The standard trim normally required on
More informationTECHNICAL DATA PILOT PRESSURE REGULATED DELUGE SYSTEM CONTROLLED BY PNEUMATIC RELEASE. 1. DESCRIPTION (Refer to Figures 1, 2 or 3.
Page 1 of 8 1. DESCRIPTION A Viking Pilot Pressure Regulated Deluge System utilizes a Viking Flow Control Valve to control water flow into the deluge system. The flow control valve must be installed with
More informationVertical Bladder Tanks
DATA SHEET Vertical Bladder Tanks Features UL Listed and FM Approved for use with various ANSUL proportioners and foam concentrates 175 psi (12.1 bar) maximum allowable working pressure (design pressure)
More informationHighVac Pumps. High Vacuum Venturi Pumps. Modular Venturi Vacuum Pumps with Solenoid-Operated Vacuum and Blow-Off
Modular Venturi Vacuum Pumps with Solenoid-Operated Vacuum and Blow-Off Vaccon offers a High Vacuum Venturi Pump in a variety of performance ranges. Each HighVac Series Pump is capable of 29.5 Hg [999mbar]
More informationTECHNICAL DATA. Trimpac 257a. September 16, 2013
September 16, 2013 Trimpac 257a 1. DESCrIpTION DESCRIPTION The Viking Double SUREFIRE SIngle Interlock Preaction TRIMPAC Model D-2 and D-2B used with either a Model E or F Deluge Valve (A.1), a Viking
More informationTECHNICAL DATA 3 MODEL G-3000 DRY VALVE RISER ASSEMBLY
Page 1 of 13 1. DESCRIPTION The Viking 3 Model G-3000 Dry Valve Riser Assembly is equipped with a small profile, light weight, pilot operated valve that is used to separate the water supply from the dry
More informationTECHNICAL DATA. Page 1 of 8. model f /2 (dn40) & 2 (dn50)
Page 1 of 8 1. DESCRIPTION The Viking Model F-1 Deluge Valve is a quick opening, differential diaphragm, flood valve with one moving mechanism. The Deluge Valve is used to control water flow in Deluge
More informationPressure booster. Air Service Units Series Page. General 5.1. Pressure boosters ø Pressure boosters ø 40 c/w air pressure regulator 5.
Series 17 Pressure booster Page General Pressure boosters ø 4 Pressure boosters ø 4 c/w air pressure regulator Pressure booster ø 63 Pressure booster ø 63 c/w air pressure regulator Pressure booster ø
More informationTECHNICAL DATA OBSOLETE
June 1, 2007 Spray Nozzles 33a_Euro Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com 1. PRODUCT NAME Viking Model EM Low Pressure Mist Nozzle System
More informationFoam Systems. Fire Protection Solutions
Foam Systems Fire Protection Solutions Foam Extinguishing Systems Foreword Foam fire suppression systems are, in most cases, the only suitable solution for the protection of special hazards. They are widely
More informationECS Protector Nitrogen Inerting Vent (PAV-WN)
ECS Protector (PAV-WN) U.S. Pat. No. 8,636,023, 9,526,933 and 9,717,935 B2 Specifications Stock Number: Service Pressure: Regulator Setting: System Connection: Temperature Range: Dimensions: Weight: Clear
More informationTECHNICAL DATA. Notes: For use with Trim Charts on Pages 2-4
Page 1 of 5 Telephone: 29-95-9501 Technical Services: 877-8-5 Fax: 29-8-0 Email: techsvcs@vikingcorp.com Model F Dry Valve with Trim Valve Size Part Number 17PTR 175PTR 17PTR Standard Trim Sets include
More informationTECHNICAL DATA PILOT PRESSURE REGULATED DELUGE SYSTEM CONTROLLED BY ELECTRIC RELEASE 1. DESCRIPTION 2. LISTINGS AND APPROVALS 3.
Page 1 of 8 1. DESCRIPTION A Viking Pilot Pressure Regulated Deluge System utilizes a Viking flow control valve to control water flow into the deluge system. The flow control valve must be installed with
More informationTECHNICAL DATA. Q = C v P S
Page 1 of 13 1. DESCRIPTION The Viking 6 Model G-6000 Dry Valve Riser Assembly consists of a small profile, light weight, pilot operated valve that is used to separate the water supply from the dry sprinkler
More informationXDF BURNERS DUAL FUEL EXCESS AIR BURNER FEATURES DESCRIPTION EXCESS AIR OPERATION
DUAL FUEL EXCESS AIR BURNER MODEL: 3610, 3651 Revision: 0 FEATURES Burns all fuel gases or light oils Nozzle mix design for on ratio control or excess air 350% excess air all sizes on gas or oil Turndown
More informationTECHNICAL DATA MAINTENANCE AIR COMPRESSOR MODEL G-1
Dry 131h 1. DESCRIPTION The Viking Model G-1 Maintenance Air Compressor is an electric motor-driven, aircooled, single-stage, oil-less compressor. The unit is equipped with a check valve and provides a
More informationPropor tional Re lief Valve s
www.swagelok.com Propor tional Re lief Valve s R Series Liquid or gas service Set pressures from 10 to 6000 psig (0.68 to 413 bar) 1/4 and 1/2 in. and 6 to 12 mm end connections Proportional Relief Valves
More informationTECHNICAL DATA Q = C. v P S. 2 Model G-2000 Dry valve. Page 1 of 13
Page 1 of 13 1. Description The Viking 2 Model G-2000 Dry Valve Riser Assembly consists of a small profile, light weight, pilot operated valve that is used to separate the water supply from the dry sprinkler
More informationMLS Series Liquid Level Switches. Installation and Operations Manual Section 15
MLS Series Liquid Level Switches Installation and Operations Manual 00-02-0730 2012-11-11 Section 15 In order to consistently bring you the highest quality full featured products, we reserve the right
More informationTECHNICAL DATA. Q= Cv S
Page 1 of 13 1. DESCRIPTION The Viking 4 inch Model G-4000 Dry Valve Riser Assembly consists of a small profile, light weight, pilot operated valve that is used to separate the water supply from the dry
More informationVertical and Horizontal Bladder Tanks
DATA SHEET Vertical and Horizontal Tanks Application The ANSUL bladder tank is one component in a balanced pressure proportioning system. Its operation requires no external power other than a pressurized
More informationFOAM TANK (1/2) DATA SHEET
FIRE FIGHTING EQUIPMENT DATA SHEET FOAM TANK (1/) DATA SHEET JOB NO. : RFQ. NO. : ISSUE : SHEET OF 01 CUSTOMER : ITEM NO. : 0 PROJECT : QUANTITY : 0 LOCATION : SERVICE : FOAM SYSTEM 0 05 CODE & STANDARDS
More informationTECHNICAL DATA SINGLE INTERLOCKED PREACTION SYSTEM WITH PNEUMATIC RELEASE
1 of 10 1. DESCRIPTION (Refer to Figures 1-3.) Viking supervised Single Interlocked Preaction Systems utilize a Viking Deluge Valve and a pneumatically pressurized automatic sprinkler system. The system
More informationMEGR-1627 Instruction Manual
MEGR-1627 HIGH FLOW GAS REGULATOR Instruction Manual- Look Inside For: Description Installation Remote Vent Line Installations Startup and Adjustment Shutdown Maintenance Body Maintenance Procedures Diaphragm
More informationModel MTB-ASME Vertical Bladder Tanks
DATA SHEET Model MTB-ASME Vertical Bladder Tanks Features n UL Listed for use with various proportioners and foam concentrates n 175 psi (12.1 bar) maximum allowable working pressure (design pressure)
More informationALF400 to 900, ALT-5/-9
Auto Feed Lube, Auto Feed Tank 00 to 900, -/-9 Standard Specifications Auto feed lube 00 00-0 00 00 00 900 - --IS- -9 AIR : OIL : Fluid Proof pressure Air. MPa 0. MPa.0 MPa (Note ) Operating pressure differential
More informationTECHNICAL DATA. Inlet Type Outlet Type OBSOLETE. 4. TECHNICAL DATA Approvals:
February 11, 2005 Deluge Valves 218 a 1. PRODUCT NAME Viking Model F-1 Deluge Valve 8" - Manufactured since 2002 4" & 6" - Manufactured since 2003 2-1/2" & 3" - Manufactured since 2004 2. MANUFACTURER
More informationModel MTB-ASME Vertical Bladder Tanks
DATA SHEET Model MTB-ASME Vertical Bladder Tanks Features n UL Listed for use with various proportioners and foam concentrates n 175 psi (12.1 bar) maximum allowable working pressure (design pressure)
More informationFlow Material Length. Weight GPM LPM. Style 3095
Akron Municipal Eductors feature a large, easy to read, and removable metering dial with infinite settings between 0% and 6%. Detents at 1 4, 1 2, 1, 3 and 6%. The Eductors are rated to flow at 200 psi
More informationPro-V Multivariable Flowmeter Model M22 In-line Vortex
Pro-V Multivariable Flowmeter Model M22 In-line Vortex Pro-V TM Advantage: Volumetric or mass flow monitoring of most liquids, gases, and steam Multivariable meter delivers mass flow, temperature, pressure,
More informationSELECTION GUIDE SELECTION GUIDE. Pressure, Flow, Level & Temperature Products for Ultra-Clean Processing P R E C I S I O N S E N S O R S
SELECTION GUIDE SELECTION GUIDE Pressure, Flow, Level & Temperature Products for Ultra-Clean Processing P R E C I S I O N S E N S O R S S t a i n l e s s S t e e l P r e s s u r e S w i t c h e s f o r
More informationCASH VALVE TYPE KP BACK PRESSURE VALVES
A high capacity pilot operated back pressure valve that offers accurate control and dependable protection against overpressure conditions FEATURES Automatically maintains maximum pressure in a vessel or
More informationFoam Chamber Model-FC
Tel: 00-44-8450751042 Fax: 00-44-8450751043 Email: info@fireguard-uk.com 2nd FLOOR 145-157 ST.JOHNS STREET LONDON EC1V 4PY UNITED KINGDOM Foam Chamber Model-FC TECHNICAL DATA : MODEL SIZE inlet WORKING
More informationInstallation Operation Maintenance
682 Seal Cooler New generation seal cooler to meet and exceed the seal cooler requirements stated in the 4th Edition of API Standard 682 Installation Operation Maintenance Experience In Motion Description
More informationWastewater combination air valve in stainless steel AISI 316 Mod. SCS
Wastewater combination air valve in Mod. SCS The air valve guarantees the proper operation of sewage/industrial lines allowing the entrance of large quantity of air in case of pipe bursting or draining,
More informationAuto Feed Lube, Auto Feed Tank ALF400 to 900, ALT-5/-9
Auto Feed Lube, Auto Feed Tank 00 to 900, -/-9 Standard Specifications Fluid Proof pressure Operating pressure differential range (Difference between tank pressure and line pressure) Vibration resistance
More informationMass Flow Controllers
Mass Flow Meters & Controllers HFM-D-3A & 305A Mass Flow Meters HFC-D-3A & 307A Mass Flow Controllers FEATURES Range 0-25 slm to 0-2500 slm (N 2 Equivalent) Excellent Accuracy ±(0.5% of Reading + 0.2%
More information1805 Series Relief Valves
October 2011 1805 Series Relief Valves P1026 1805G Type 1805-2 Type 1805-4 Figure 1. Typical 1805 Relief Valves Introduction The 1805 Series relief valves are designed for use in farm tap applications
More informationKECKLEY INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS TYPE NO. 7 FLOAT VALVE
INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS TYPE NO. 7 FLOAT VALVE APPLICATION/SERVICE: The NO. 7 internally piloted valves are recommended where tight closing is essential. The NO. 7 is most
More informationBladder Tank Installation & System Design Information
Bladder Tank Installation & System Design Information The Chemguard Bladder Tank is one component in a balanced pressure foam proportioning fire protection system. It requires no external power other than
More informationGAS PRESSURE REGULATORS AP
A Long Experience in Energy Equipment and one Goal: The Customer s satisfaction. GAS PRESSURE REGULATORS AP (High Pressure) ALPHARD P/AP Pressure Regulator Applications It is designed for use in transmission
More informationLAKOS Waterworks. PWC Series Sand Separators. Installation & Operation Manual LS-829 (10/12)
LAKOS Waterworks PWC Series Sand Separators Installation & Operation Manual LS-829 (10/12) Table of Contents Separator Operation... 3 Individual Model Details.... 4 Flow vs. Pressure Loss Chart 4 Installation
More informationpvc well casing & drop pipe
C e r t a i nte e d pvc well casing & drop pipe P V C We l l P r o d u c t s Sure Fit PVC well casing and drop pipe have gained broad acceptance since their introduction almost 40 years ago. Today, due
More informationTECHNICAL DATA DELUGE VALVE, MODEL F-1 STRAIGHT THROUGH STYLE
Page 1 of 10 1. DESCRIPTION The Viking Model F-1 Deluge Valve is a quick opening, differential diaphragm and flood valve with one moving mechanism. The Deluge Valve is used to control water flow in Deluge
More informationUBEC 1AT. AUTO TANK Fill System Installation, Operation, & Setup Instructions
Document Number: XE-ATA5PM-R1A UBEC 1AT AUTO TANK Fill System 08899155 Installation, Operation, & Setup Instructions Rev170906-EB-FRC PHYSICAL: 1302 WEST BEARDSLEY AVE ELKHART, IN 46514 WWW.ELKHARTBRASS.COM
More informationGeneral. Rugged, Reliable with Value-added Features. Pipe Sizes. Temperature Limits. Spring Ranges. Buried Service. Increased Outlet Pipe Sizes
DS-G-REG-13-43-0812-01-A* Model 243-RPC Pilot Operated Regulators Installation and Maintenance Instructions Rugged, Reliable with Value-added Features Genuine, pilot-operated regulators use the same relay
More information