SERIES & NO. SMI - 115
|
|
|
- Emil Glenn
- 5 years ago
- Views:
Transcription
1 1 of PURPOSE To provide a system of handling and storing compressed gas and fuel gas cylinders. This instruction details the materials and methods used to handle and store cylinders. All contractors performing work on Corporation property shall be instructed to follow the provisions of this instruction. 2.0 REFERENCE Plant Engineering and Environmental Planning Office Procedure No Federal and State Occupational Safety and Health Acts MTI SMI - 116, "Certification of Arc and Gas Cutters and Welders" MTI SMI - 118, " Use of Oxygen - Fuel Gas Equipment" 3.0 FUNCTIONS AFFECTED Manufacturing Engineering Facilities Engineering Production Control Employee Safety Security and Fire Prevention Services Industrial Hygiene 4.0 OPERATION AFFECTED Chrysler Corporation and Subsidiaries 5.0 INFORMATION AND INSTRUCTIONS 5.1 Handling Cylinders may be moved for short distances by tipping and rolling them on the bottom edge, but shall not be bumped or dropped. Nor shall cylinders be dragged, rolled horizontally or slid. Rough handling may cause:
2 2 of 7 A. The cylinder valve to break. This could bring about an explosion or a violent movement of the cylinder. B. Cylinder leaks or ruptures. Escaping gas may cause a fire, explosion or severe injuries Cylinders shall always be transported in a firmly secured vertical position. Exhibit A shows a single cylinder truck. Exhibit B shows a fork truck rack suitable for moving several cylinders. Welding cart, NPWW-100, may be used for transporting two cylinders Cylinders in Emission Test Areas are generally handled in Multiple Cylinder Wheeled Specialty Gas Service Carts. Most commonly used are the six or eight cylinder capacity gas service carts referred to as the Six Pak or 8 Pak carts. Exhibit C illustrates the Six Pak Cart Specially designed powered vehicles may also be used for transporting cylinders in an upright contained position Cylinders may be lifted by cranes with a properly designed rack or cradle, but shall not be lifted by a lifting magnet or a rope, chain, or wire rope sling All Cylinders, full or empty, shall be handled with caution Valve-protection caps shall not be used for lifting cylinders from one position to another. 5.2 Storage Empty cylinders are marked "EMPTY" or "MT", removed immediately from the working area and stored in an area separated from full cylinders Defective and/or leaking cylinders shall be moved to an isolated area outdoors, away from sources of ignition Cylinders containing in excess or 2000 cubic feet of gas shall be stored in a well-ventilated separated room or area Cylinders shall be stored and firmly supported in an upright position. Valves shall be closed and cylinders shall be capped Oxygen cylinders in storage shall be separated from fuel-gas cylinders a minimum distance of twenty
3 3 of 7 feet (20') or by a non-combustible barrier at least five feet (5') high having a fire-resistance rating of at least one-half (1/2) hour Cylinders shall be stored in dry areas, protected from the weather and sudden temperature changes. Cylinders shall not be stored near furnaces, radiators, in direct sunlight, etc. Heat will increase the pressure in the cylinder Storage areas shall be clean and free from oils, greases, and other flammable materials Storage areas inside buildings shall be protected by sprinkler systems whenever feasible Storage areas for cylinders shall be on a level, fireproof floor and shall be well ventilated to prevent the accumulation of gases Sources of ignition in cylinder storage areas shall not be permitted. Electrical wiring shall be in conduit. Electric lights shall be enclosed to prevent ignition of gases, and covered by guards to prevent breakage. Electric switches shall be located outside the storage areas. Smoking shall not be permitted Only cylinders conforming to O.S.H.A. specifications shall be allowed in Chrysler facilities Cylinders shall not be stored in a location where they may become damaged or knocked over by passing or falling objects Where a cylinder is designed to accept a valve protection cap, caps shall be kept in place except when the cylinder is in use or is connected for use All employees assigned to the handling of cylinders under pressure shall be adequately trained prior to assignment. 6.0 EXHIBITS Exhibit A - Single Cylinder Transport Truck Exhibit B - Multiple Cylinder Fork Truck Rack Exhibit C - Multiple Cylinder Wheeled Specialty Gas Service Cart
4 4 of 7
5 5 of 7
6 6 of 7
7 7 of 7
Savard Labor & Marine Staffing, Inc. Compressed Gas Safety Program Rev3/14
Compressed Gas Safety Program Purpose: The purpose of this safety policy and procedure is to establish guidelines for the protection and safety of this company s employees who handle and use compressed
CITY AND COUNTY OF DENVER CR&CF RISK UNIT Compressed Gas Safety Standard
CITY AND COUNTY OF DENVER CR&CF RISK UNIT 65.5.11 Compressed Gas Safety Standard 1.0 Introduction 2.0 Scope This standard has been developed to protect all City and County of Denver employees and contractors
Section 35 Brieser Construction SH&E Manual
Brieser Construction SH&E Manual August 2017 Assure that employees handling compressed gases are adequately trained in the inherent hazards of the cylinders and their contents, as well as proper handling,
WHAT IS GAS TANK/CYLINDER?
Introduction To use compressed gas cylinders safely, it is important that they are stored properly, handled correctly, used with the correct equipment, and that the properties of the gases they contain
Compressed Gasses Safety
COMPRESSED GASES SAFETY Last Modified: APR 2015 1 of 6 Compressed Gasses Safety 1 PURPOSE To provide guidelines for transport, storage, handling, and use of cylinders containing compressed gas. 2 SCOPE
ESSENTIAL SAFETY RESOURCES
ESSENTIAL SAFETY RESOURCES GS-3007 COMPRESSED GAS CYLINDERS Originator: Safety Advisor s Signature: Type Name Approval: HSE Manager s Signature: Type Name Approval: Operations Manager s Signature: Type
Process Name Compressed Gas Cylinders Program
CNM WAY PROCESS CNM Process Name Compressed Gas Cylinders Program (07/11/2018 Revision) Overview of Compressed Gas Cylinders Program Purpose: To prevent injury from failure of compressed gas cylinders
COMPRESSED GAS CYLINDERS
Title: Compressed Gas Cylinders Effective Date: 7/2/2014 Control Number: THG_0044 Revision Number: 1 Date: 10/23/2015 Annual Review Completed: 5/13/2015 CONTENTS I. PURPOSE II. SCOPE III. KEY RESPONSIBILITIES
This written Compressed Gas Plan is kept at the corporate office and in the written Safety & Health Program.
Safety & Health Program 10627 Midwest Industrial Boulevard, St. Louis, MO Phone: 314-785-6425 Fax: 314-785-6426 Compressed Gas Plan Purpose It is the policy of EMA to permit only trained and authorized
Compressed Gases Storage and Handling Safety Policy. Individual Unit Function: Safety Procedure No.: SOP-0103 Page: 1 of 6
Procedure No.: SOP-0103 Page: 1 of 6 MIDGA Reviewed: 07/09/18 Effective: 1/14/98 Supersedes: Original Preparer: Owner: Approver: Safety Safety Safety 1. PURPOSE The purpose of this procedure is to establish
Hot Work Program. University of Wisconsin-Platteville Reviewed 4/2016
Hot Work Program University of Wisconsin-Platteville Reviewed 4/2016 The purpose of the Hot Work Program is to establish safety procedures for employees, contractors, and subcontractors engaging in any
Doc No: WELDHOT Midland Engineering Co., Inc. Initial Issue Date 12/14/15 Safety Management System
Revision Preparation: Safety Mgr Authority: President Issuing Dept: Safety Page: Page 1 of 7 PURPOSE To provide guidelines for the safe operation of welding, cutting and hot work of equipment, and to itemize
U.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL
SAFE -14 Page 1 of 8 U.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL FUNCTION Safety TOPIC Hotwork Permit Program OBJECTIVE(S): GENERAL POLICY: To provide a work atmosphere that is conducive to
CHAPTER 26 WELDING AND CUTTING
CHAPTER 26 WELDING AND CUTTING Revised 7/2010 1 WELDING AND CUTTING Responsibilities 1. The County Safety Officer is responsible for providing appropriate safety instructions for supervisor's use on welding
WELDING, CUTTING AND BRAZING
- 1 - WELDING, CUTTING AND BRAZING Are only authorized and trained personnel permitted to use welding, cutting or brazing equipment? Does each operator have a copy of the appropriate operating instructions
Date Issued: 27 September 2018
1 Introduction This Standard Operating Procedure outlines the requirements for Compressed Gas Cylinder (cylinder) storage and transport. In accordance with Provincial Legislation, the Department of Environmental
KENNECOTT UTAH COPPER CORPORATION SAFETY AND HEALTH STANDARDS COMPRESSED GAS
KENNECOTT UTAH COPPER CORPORATION SAFETY AND HEALTH STANDARDS COMPRESSED GAS Effective Date: 08/07/14 Standard: 16.15 Document Number: KUCSH0070 Rev: 05 007016.15.1 INTRODUCTION 16.15.1.1 This standard
STORAGE OF COMPRESSED GAS CYLINDERS (SAF-SPI-15)
1. PURPOSE: This SPI has been developed to ensure compliance to government regulations and to provide clear standards for storage of compressed gases. 2. CONTEXT The storage of compressed gases is legislated
Laboratory Safety Committee
Laboratory Safety Committee Compressed Gas Cylinder Policy Purpose Compressed gas cylinders are an important component of many research laboratories. Wide varieties of gases are packaged in compressed
Welding and Cutting With Oxygen-Fuel Gas
Optional Information Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: Welding and Cutting With Oxygen-Fuel Gas Self Inspection Checklist Guidelines: This checklist
This training does not attempt to cover all safety regulations or precautions.
This training does not attempt to cover all safety regulations or precautions. For additional safety regulations and precautions, see the following standards: American Welding Society (AWS) American National
Management Plan for Compressed Gas
IEA, INC. N E W P R A G U E A R E A S C H O O L S I S D # 7 2 1 A Service-Disabled Veteran-Owned Small Business Contact Us: BROOKLYN PARK OFFICE 9201 W. BROADWAY, #600 BROOKLYN PARK, MN 55445 763-315-7900
Compressed Gases and Cryogens
Compressed Gases and Cryogens University of Tennessee Safety Guide HM-011 Document Contact: EHS Date effective: January 1, 2009 Revision Date: October 1, 2015 Purpose This guideline adheres to the Occupational
SAFETY POLICY AND PROCEDURE MANUAL All Euramax Subsidiaries. Number K-3.0 Welding Safety Procedures
Number K-3.0 Issued: 1/2009 Revised: 3/2016 Page 1 of 3 1.0 PURPOSE: To standardize procedures associated with production and maintenance welding and to minimize the potential risk of accident or injury
General Precautions for handling compressed gases
General Precautions for handling compressed gases Introduction Compressed gas cylinders can be extremely hazardous when misused or abused. Compressed gas cylinders can present a variety of hazards due
Safe Work Instructions For Oxygen Acetylene Equipment
Safe Work Instructions For Oxygen Acetylene Equipment Policy Sponsor: Assistant Vice President Facilities Management Responsible Unit: Trade Services Approval Date: September 2010 Revisions: January 2018
Cal/OSHA T8 CCR 1536 Cal/OSHA T8 CCR 4799 Cal/OSHA T8 CCR 4845 Cal/OSHA T8 CCR 4848
Cal/OSHA Gas Systems for Welding GAS WELDING Cal/OSHA T8 CCR 1536 Cal/OSHA T8 CCR 4799 Cal/OSHA T8 CCR 4845 Cal/OSHA T8 CCR 4848 When performing gas welding, the following precautions, work procedures,
Material Handling and Storage of compressed gases and Air equipment
Material Handling and Storage of compressed gases and Air equipment Compressed gases can be toxic, flammable, oxidizing, corrosive, inert, or some combination of these hazards. Compressed gas cylinders
Welding and Cutting (Hot Work) Operations Self-Audit Checklist. Building Room Supervisor Date
Welding and Cutting (Hot Work) Operations Self-Audit Checklist Building Room Supervisor Date Audit Performed by A. General Welding and Cutting Controls 1. Welding and cutting operations restricted to authorized
CALL BEFORE YOU DIG POLICY AND PROCEDURE
CALL BEFORE YOU DIG POLICY AND PROCEDURE Prepared By: Triumvirate Environmental Developed: December 2012 Updated: Program Approval Associate Vice President of Public Safety & Administrative Services Associate
OXYGEN ACETYLENE WELDING & CUTTING EQUIPMENT
OXYGEN ACETYLENE WELDING & CUTTING EQUIPMENT Introduction: The oxy-acetylene torch can be used for various tasks. It can be used for cutting steel, welding steel, brazing and for heating metal. The oxy-acetylene
SAFETY DIRECTIVE 3.0 REFERENCES. 3.1 See Appendix B
SAFETY DIRECTIVE Title: Hot Work Issuing Department: Town Manager s Safety Office Effective Date: September 1, 2014 Approved: Gilbert Davidson, Town Manager Type of Action: New 1.0 PURPOSE To provide proper
ASHE Monograph. Medical Gas Cylinder and Bulk Tank Storage
ASHE Monograph Medical Gas Cylinder and Bulk Tank Storage ASHE Monograph Medical Gas Cylinder and Bulk Tank Storage Susan B. McLaughlin, MBA, FASHE, CHFM, CHSP David A. Dagenais, CHSP, CHFM, SASHE JUNE
WELDING AND CUTTING GUIDELINES
Page 1 of 8 University employees should observe the following general safety guidelines when performing hot work operations. Also see the Hot Work Guidelines EH&S 02-008. Hot work is defined as: brazing,
COMPLIANCE WITH THIS PUBLICATION IS MANDATORY
BY ORDER OF THE COMMANDER 59TH MEDICAL WING 59TH MEDICAL WING INSTRUCTION 41-203 9 MARCH 2018 Health Services CYLINDER-GASES (COMPRESSED AND LIQUEFIED) COMPLIANCE WITH THIS PUBLICATION IS MANDATORY ACCESSIBILITY:
Compressed Gas Cylinders - Guideline
Environmental Health and Safety Compressed Gas Cylinders - Guideline Date of Issuance: 1/10/18 Revision Number: Initial Revision Date: Prepared by: EH&S 1. Purpose Carnegie Mellon University has developed
HOT WORK SAFETY 29 CFR WELDING & CUTTING SAFETY (HOT WORK)
Title: Hot Work/Welding Effective Date: 2/6/2013 Control Number: THG_0011 Revision Number: 1 Date: 10/10/2015 Annual Review Completed: 5/13/2015 CONTENTS HOT WORK SAFETY 29 CFR 1910.252 WELDING & CUTTING
In This Document. Welding and Cutting Lesson Plan. Overview
Welding and Cutting Lesson Plan Sample Lesson Plan In This Document Construction Training Program (10-hour) Planning the Lesson Presenting the Lesson Overview Evaluate Student Learning Working with welding
Welding, Cutting, and Brazing
Welding, Cutting, and Brazing Hazards of Welding Operations Fire hazards Metal splatter Electric shock Explosion hazards Released gases Radiant energy Where would these hazards be found on oil and gas
Health and Safety Guidance Note No 37
Health and Safety Guidance Note No 37 THE SAFE USE AND STORAGE OF GAS CYLINDERS Accidents involving gas cylinders can cause serious injury or even death. The legal term for gas cylinders is transportable
DSEAR- Storage, Use and handling of gas cylinders guidance.
OHSS: Storage, Use and handling of gas cylinders guidance 202 DSEAR- Storage, Use and handling of gas cylinders guidance. Contents Introduction... 2 General recommendations for storage, use and handling....
A guide to Part 10 of the
OCCUPATIONAL HEALTH AND SAFETY DIVISION Welding, Cutting, Burning and Soldering A guide to Part 10 of the Occupational Safety General Regulations October 2007 A GUIDE TO PART 10 WELDING, CUTTING, BURNING
Risk Management Department. Compressed Gas Safety
Risk Management Department Compressed 1 Introduction Many maintenance and vocational education operations require the use of compressed gases. 2 Introduction In this presentation we will discuss: Hazards
Developing a Policy for Auto Transportation of Medical Oxygen in High Pressure Cylinders and Cryogenic Vessels
Developing a Policy for Auto Transportation of Medical Oxygen in High Pressure Cylinders and Cryogenic Vessels Since 1993, Applied Home Healthcare Equipment LLC has published numerous publications, videos,
Handling and Storage of Gases
Handling and Storage of Gases Learning Outcome When you complete this module you will be able to: Describe the procedures for safe storage and handling of cylinders containing gases. Learning Objectives
PURPOSE OF THE POLICY
Title: Safe Storage, Handling, Use and Disposal Procedures of Compressed Gas Cylinders Effective Date: November 2005 Revision Date: March 1, 2017 Issuing Authority: Responsible Officer: VP, Capital Projects
Material Safety Data Sheet Oxygen
Material Safety Data Sheet Oxygen Section 1 : PRODUCT AND COMPANY IDENTIFICATION Product name: Oxygen Supplier/ Manufacturer: Synonyms: Oxygen, Compressed, Oxygen USP Business Phone: Premier Medical Corporation
COMPANY HEALTH & SAFETY PROGRAM. Title: Welding & Cutting Section No: 45
Page 1 of 10 1.0 PURPOSE The purpose of this section is to heighten employee awareness of potential welding and cutting hazards, and to communicate acceptable work practices. It is intended that supervisors
Hazard Communications. Your Right to Know
Hazard Communications Your Right to Know Hazard Communication Standard (HCS) 29 CFR (Code of Federal Regulations) 1910.1200 Hazard Communication The purpose of this is to ensure that the hazards of all
CHAPTER 28: HOTWORK (WELDING/OXYGEN-ACETYLENE GAS)
CHAPTER 28: HOTWORK (WELDING/OXYGEN-ACETYLENE GAS) 1.0 OXYGEN ACETYLENE WELDING AND CUTTING 1.1 OXYGEN ACETYLENE WELDING AND CUTTING Oxygen-fuel gas cutting depends on the heat produced by the combustion
Welding/Cutting/Brazing with Hot Work Permit
Welding/Cutting/Brazing with Hot Work Permit For Adopted LC-1012a Rev. 06/16 Page 1 Introduction As part of Organization s overall safety and
UTMB RESPIRATORY CARE SERVICES GUIDELINES Respiratory Care Services Medical Gas Cylinder Storage, Use and Transport
Page 1 of 4 I. Title Medical Gas. II. III. IV. Policy This policy applies to all departments and areas where medical gases are used, stored or transported for patient care activities. Respiratory Care
Section 1.3: PRESSURE VESSEL COMPONENTS AND SYSTEMS AND COMPRESSED GAS CYLINDERS
Section 1.3: PRESSURE VESSEL COMPONENTS AND SYSTEMS AND COMPRESSED GAS CYLINDERS TABLE OF CONTENTS Page A. Regulations, Standards and References 1.3-2 B. Scope 1.3-2 C. Design Features for the Storage
CALIFORNIA STATE UNIVERSITY, LOS ANGELES WELDING, CUTTING, AND HOT WORK OPERATIONS. October 2007
CALIFORNIA STATE UNIVERSITY, LOS ANGELES WELDING, CUTTING, AND HOT WORK OPERATIONS October 2007 PROGRAM APPROVAL AND AUTHORIZATION James M. Rosser, President Date TABLE OF CONTENTS TITLE SECTION PURPOSE
Compressed Gases Safety Program
Compressed Gases Safety Program Summary: Compressed gas cylinders can present a variety of hazards due to their pressure and /or contents. This program covers requirements which must be followed for the
Section 20 TABLE OF CONTENTS Pressurized Equipment and Systems. 20.A General B Compressed Air and Gas Systems
Section 20 TABLE OF CONTENTS Pressurized Equipment and Systems Section: Page 20.A General... 20-1 20.B Compressed Air and Gas Systems... 20-4 20.C Boilers and Systems... 20-7 20.D Compressed Gas Cylinders...
Rockhampton Office Brisbane Office Tarong Site. Barron Gorge Hydro PS Kareeya Hydro PS Mica Creek PS
Business Procedure Hot Work Document Number OHS-PROC-128 This document applies to the following sites: All Sites Rockhampton Office Brisbane Office Tarong Site Barron Gorge Hydro PS Kareeya Hydro PS Mica
Peninsula Dental Social Enterprise (PDSE)
Peninsula Dental Social Enterprise (PDSE) Medical Gas Policy Version 3.0 Date approved: August 2018 Approved by: The Board Review due: August 2021 Policy will be updated as required in response to a change
Safety and Health Policy and Procedure Manual. WELDING, CUTTING, and BRAZING PROGRAM Section 0140
Safety and Health Policy and Procedure Manual WELDING, CUTTING, and BRAZING PROGRAM Section 0140 I. INTRODUCTION II. SCOPE III. STANDARD IV. GENERAL REQUIREMENTS A. Basic Precautions for Fire Prevention
I. Subject: Compressed gas cylinders, regulators, and portable liquid systems.
I. Subject: Compressed gas cylinders, regulators, and portable liquid systems. II. Objective: To provide safe and effective use, storage, and transport of therapeutic gases. II. Procedure: A. Compressed
UNIVERSITY OF PITTSBURGH HOT WORK PROGRAM
University of Pittsburgh 1 Hot Work Program July 2003. UNIVERSITY OF PITTSBURGH HOT WORK PROGRAM All hot work can create conditions with high probability for fire related injury or property loss. Hot work
Risk assessment. Assessment details. Task. Introduction. Please complete the form as fully and accurately as you can. Assessors job title
Risk assessment Introduction Please complete the form as fully and accurately as you can. Assessment details Name of organisation Assessor's name Assessors job title Any Company John Smith Manager Date
Section 2 Safety, Tools and Equipment, Shop Practices Unit 4 General Safety Practices. Unit Objectives. Pressure Vessels and Piping (1 of 2)
Section 2 Safety, Tools and Equipment, Shop Practices Unit 4 General Safety Practices Unit Objectives After studying this chapter, you should be able to: Describe proper procedures for working with pressurized
Compressed Gas Cylinder Safety
Session No. 666 Compressed Gas Cylinder Safety David R. Maloney CGS Safety Training, Inc. Farmington Hills, Michigan We take for granted the power a compressed gas cylinder possesses. Think about it, most
Working Environment Safety Assessment
For your own safety and/or safety of your workforce, and to improve the efficiency of your business practices, you should be aware of, and be up to date with, the key safety issues and good practices relevant
UNIVERSITY OF ROCHESTER ENVIRONMENTAL HEALTH & SAFETY
Revision No.: New Page 1 of 9 I. PURPOSE It is a requirement that all University of Rochester employees who handle compressed gases understand the health and safety hazards of the compressed gas cylinders,
Wilkins Safety Group
Gas Welding INTRODUCTION Welding is the union of pieces of metal by fusing the opposing surfaces that have been made molten by heat. Processes similar to welding include brazing and soldering. Allied processes
WELDING & CUTTING FIRE PROTECTION SAFETY 1 NAVFAC
WELDING & CUTTING FIRE PROTECTION SAFETY 1 NAVFAC BASIC TYPES OF WELDING ARC WELDING 2 NAVFAC OXY/ACETYLENE OR FUEL GAS WELDING FUEL GASES USED FOR HEATING & CUTTING OPERATIONS 3 MAJOR TYPES 1. P GAS {Propane}
CITY AND COUNTY OF DENVER POLICY DENVER FIRE DEPARTMENT. Number: 2015 IFC Effective Date: February 1, 2017 Page 1 of 5
Subject: COMPRESSED GAS Reference: IFC, Denver Amendments, NFPA Approved: Manuel Almaguer Division Chief, Fire Prevention Division Number: 2015 IFC- 5301-1 Effective Date: February 1, 2017 Page 1 of 5
PRESSURIZED EQUIPMENT AND SYSTEMS
SECTION 20 PRESSURIZED EQUIPMENT AND SYSTEMS 20.A GENERAL 20.A.01 Inspections and tests - general. a. Pressurized equipment and systems shall be inspected and performance tested before being placed in
MSDS Interspiro Spiroscape EEBD (compressed breathing air)
MSDS Interspiro Spiroscape EEBD (compressed breathing air) 1. Product and company information Chemical name; Class: air Synonyms: Medical air, breathing air, compressed air Chemical family name: Non flammable
Material Safety Data Sheet (MSDS)
SUPASTAINLESS 98 Material Safety Data Sheet SUPPLIER DETAILS Supplier Name: Renegade Gas (Pty) Ltd T/A Supagas (NSW) & Supagas (QLD) Head Office Address: 5 Benson Road, Ingleburn, 2565 Telephone: (02)
Hot Work Program. California State University, Chico. Department of Environmental Health and Safety
California State University, Chico Department of Environmental Health and Safety May 2017 Table of Contents Section 1.0 Introduction... 1-1 2.0 Definitions... 2-1 3.0 Hot Work Precautions and Procedures...
WELDING AND OTHER HOT WORK
CHAPTER 26 WELDING AND OTHER HOT WORK SECTION 2601 GENERAL 2601.1 Scope. Welding, cutting, open torches and other hot work operations and equipment shall comply with this chapter. Exception: Hot work on
CITY AND COUNTY OF DENVER POLICY DENVER FIRE DEPARTMENT
Reference: IFC, Denver Amendments, NFPA Approved: Joseph L. Gonzales, Division Chief, Fire Prevention and Investigation Division Number: IFC- 3001-1 Effective Date: February 1, 2012 Page 1 of 5 This policy
Safe Handling of Pressurized Gases and Cylinders. Dr. Michael Hanisch
Safe Handling of Pressurized Gases and Cylinders Dr. Michael Hanisch Pressurized Gases Safety - Introduction Even a wall will not stop me! Pressurized Gases Safety - Introduction Objectives Protection
OSHA Subpart I Tools - Hand & Power
OSHA Subpart I Tools - Hand & Power 1926.300 General Requirements (b) Guarding (1) When power operated tools are designed to accommodate guards, they shall be equipped with such guards when in use. Guards
Hazard Identification and Risk Assessment Form. Risk Assessment
Identification and Assessment Form Assessment Tool & Machine Work General Various injuries (including potential fatalities) All staff complete safety induction programme at the start of the module. instructed
Safety, Set-Up, and Operating Instructions
Read all Instruction, SAVE THESE INSTRUCTION Safety, Set-Up, and Operating Instructions Gas Welding, Cutting, Brazing & Heating There are many hazards to be considered when using oxy-fuel welding, cutting,
Hot Work Safety Program and Procedures
Page 1 of 15 Sect: 1.0 Purpose Welding and Hot Work, such as brazing or grinding, present a significant opportunity for fire and injury. All precautions of this program must be applied prior to commencing
Confined Spaces OSHA 1926 AA
Confined Spaces OSHA 1926 AA 1926.1201-1213 Confined Spaces Objectives: Understanding why the OSHA requirements are needed Identify four categories of hazards that may be present entering in confined spaces
New Employee Safety Indoctrination Checklist
New Employee Safety Indoctrination Checklist Emergency Response Training Read and understand the Facility s Emergency Response Action Plan Complete Emergency Response Training Locate the Facility s Evacuation
SHOP SAFETY INSPECTIONS
SHOP SAFETY INSPECTIONS SOP No 1.014 1 PURPOSE 1.01 This document details the procedures and forms to be used when performing safety inspections for shops. 2 EXPECTATIONS 2.01 Shops and storage closets
GUIDELINES ON SAFE HANDLING AND STORAGE OF COMPRESSED GASES CHEMICAL MANAGEMENT CENTRE
Page No. 1 of 6 Compressed gases are widely used in both teaching and research laboratories across UTM. The pressure at which gases are contained in gas cylinders can be extremely high, which makes it
ASSEMBLY & OPERATIONS MANUAL. Straight & Clean Torch Cuts. Every Time.
ASSEMBLY & OPERATIONS MANUAL Straight & Clean Torch Cuts. Every Time. CAUTION ALWAYS USE FLASH BACK ARRESTORS (purchased separately) READ THIS BOOK THOROUGHLY AND FOLLOW INSTRUCTIONS! FAILURE TO USE OSHA
5.0 Store. safely IN THIS SECTION: 5.1 Decanting or transferring
5.0 Store hazardous substances safely IN THIS SECTION: 5.1 Decanting or transferring hazardous substances 5.2 Incompatibles 5.3 Store only what you need, store it safely 5.4 Gas cylinders 5.5 Oxy-acetylene
Bauman Machine Inc. COMPRESSED GAS CYLINDER SAFETY
Bauman Machine Inc. COMPRESSED GAS CYLINDER SAFETY Many industrial and laboratory operations require the use of compressed gases for a variety of different operations. Compressed gases present a unique
Hydrogen in Air % to 2%
Kele part# GAS-H2-2 Emergency Contact: Chemtrec (800) 424-9300 Or rco (208) 336-1643 1125 West Amity Road Boise, ID 83705 (208) 336-1643 Hydrogen in Air 0.0001% to 2% Identification Product Name: Hydrogen
Compressed Gas Safety General Safety Guidelines
Compressed Gas Safety General Safety Guidelines Occupational Safety & Health Bureau Montana Department of Labor & Industry Prepared for Montana Employers by the Occupational Safety & Health Bureau Department
TABLE OF CONTENTS PART 2 - CONFINED SPACES
May 11, 2006 TABLE OF CONTENTS PART 2 - CONFINED SPACES Page DEFINITIONS... 2-1 GENERAL... 2-2 RESPONSIBILITIES... 2-2 HAZARD ASSESSMENT AND WORK PROCEDURES... 2-3 IDENTIFICATION AND ENTRY PERMITS... 2-3
OXYGEN GASEOUS, TECHNICAL GRADE
page 1 of 6 SAFETY DATA SHEET V4 in accordance with Regulation (EC) 1907/2006 (REACH) amеnded with Commission Regulation(EU) 2015/830 V4 amendments in this revision SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE
SAFETY POLICY AND PROCEDURE MANUAL QUESTIONNAIRE
The following questionnaire is designed to aid us in the creation of your policy and procedure manual. Please place a checkmark in the boxes that correspond to the sections that you would like to be included
Fall Protection and Elevated Work
Program No: SP-010 Page 1 1.0 PURPOSE AND INTRODUCTION Fall Protection and Elevated Work To establish fall protection safety procedures for Pitt County Schools employees engaged in any of the following
MODULE 2 BRAZING CYLINDER TRANSPORT, STORAGE AND EQUIPMENT
MODULE 2 BRAZING CYLINDER TRANSPORT, STORAGE AND EQUIPMENT ISSUED BY REVISION NUMBER REVISION DATE DOCUMENT NUMBER S. GINBEY 0 7 th Nov 2016 QP74 Module 2 Cylinder Transport, Storage & Equipment ADR Regulations
SAFETY DATA SHEET According to Regulation (EC) N 1907/2006
SAFETY DATA SHEET According to Regulation (EC) N 1907/2006 ProInert IG-541 SECTION 1: Identification of the substance/mixture and of the company/undertaking Product identifier ProInert IG-541 Use of the
Aerial Lift Safety Program
Aerial Lift Safety Program Revision Date: 6-19-2017 TABLE OF CONTENTS Aerial Lift Safety Program 1.0 Overview... 3 2.0 Policy......3 3.0 Requirements. 3 4.0 Purpose..... 4 5.0 Scope.........4 6.0 Responsibilities........7
M3060 Handling Compressed Gas Cylinders Safely. Leader s Guide
M3060 Handling Compressed Gas Cylinders Safely Leader s Guide WORKING SAFELY WITH COMPRESSED GAS CYLINDERS This easy-to-use Leader s Guide is provided to assist in conducting a successful presentation.
Safety Data Sheet. Zero Air 1 PRODUCT AND COMPANY IDENTIFICATION. Manufacturer NorLab a division of Norco 898 W. Gowen Rd.
Number: NLB 255 Page 1 of 5 1 PRODUCT AND COMPANY IDENTIFICATION Manufacturer NorLab a division of Norco 898 W. Gowen Rd. Boise, ID 8375 Contact: Phone: Fax: Web: Quality Dept. 28-336-1643 28-433-616 www.norlab-gas.com
PUBLIC COMPANY ORLEN LIETUVA OCCUPATIONAL HEALTH AND SAFETY PROCEDURE BDS-12 USE OF PORTABLE GAS ANALYZERS I. GENERAL
PUBLIC COMPANY ORLEN LIETUVA APPROVED BY Deputy Director of Quality, Labor Safety and Environmental Control Director 30 November 2017 Order No TV1(1.2-1)-457 OCCUPATIONAL HEALTH AND SAFETY PROCEDURE BDS-12
EHS Laboratory Guidance: Cryogenic Material
EHS Laboratory Guidance Cryogenic Liquids 1 Introduction/Purpose Cryogenic liquid is defined by the Idaho Fire Code as having a boiling point of less than -90º C (-130º F) at 14.7 psia (1 bar). All cryogenic