Safety Data Sheet according to (EC) No 1907/2006

Transcription

1 Safety Data Sheet according to (EC) No 1907/2006 UniBond No More Nails Interior Page 1 of 6 sds no. : Revision: printing date: SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier UniBond No More Nails Interior 1.2. Relevant identified uses of the substance or mixture and uses advised against Intended use: Assembly adhesives 1.3. Details of the supplier of the safety data sheet Henkel Limited Apollo Court, 2 Bishop Square Business Park Hatfield, Hertfordshire AL10 9EY Great Britain Phone: +44 (0) Fax-no.: +44 (0) ua-productsafety.uk@uk.henkel.com 1.4. Emergency telephone number 24 Hours Emergency Tel: For further general health & safety, technical and practical advice on this product, please call +44 (0) or write to: Technical Services; Henkel Limited; Road 5; Winsford Industrial Estate; Winsford; Cheshire; CW7 3QY- technical.services@henkel.co.uk 2.1. Classification of the substance or mixture Classification (DPD): No classification required Label elements SECTION 2: Hazards identification Label elements (DPD): The product is not subject to classification according to the calculation methods of the "General Classification Guideline for Preparations of the EC" as issued in the last version. Additional labeling: Pressurized container: protect from sunlight and do not expose to temperatures exceeding 50 C. Do not pierce or burn, even after use Other hazards None if used properly.

2 UniBond No More Nails Interior Page 2 of 6 General chemical description: Adhesive Base substances of preparation: Styrene-acrylate copolymer SECTION 3: Composition/information on ingredients Declaration of the ingredients according to CLP (EC) No 1272/2008: No data available. Declaration of ingredients according to DPD (EC) No 1999/45: Contains no dangerous substances exceeding the limits of the EU-Regulation 4.1. Description of first aid measures General information: In case of adverse health effects seek medical advice. Inhalation: Move to fresh air, consult doctor if complaint persists. SECTION 4: First aid measures Skin contact: Rinse with running water and soap. Apply replenishing cream. Change all contaminated clothing. Eye contact: Rinse immediately with plenty of running water, seek medical advice if necessary. Ingestion: Rinse mouth and throat. Drink 1-2 glasses of water. Seek medical advice Most important symptoms and effects, both acute and delayed No data available Indication of any immediate medical attention and special treatment needed See section: Description of first aid measures SECTION 5: Firefighting measures 5.1. Extinguishing media Suitable extinguishing media: carbon dioxide, foam, powder, water spray jet, fine water spray Extinguishing media which must not be used for safety reasons: High pressure waterjet 5.2. Special hazards arising from the substance or mixture In the event of a fire, carbon monoxide (CO) and carbon dioxide (CO2) can be released Advice for firefighters Wear protective equipment. Wear self-contained breathing apparatus. Additional information: Cool endangered containers with water spray jet. SECTION 6: Accidental release measures

3 UniBond No More Nails Interior Page 3 of Personal precautions, protective equipment and emergency procedures Wear protective equipment Environmental precautions Do not empty into drains / surface water / ground water Methods and material for containment and cleaning up Remove mechanically. Dispose of contaminated material as waste according to Chapter Reference to other sections See advice in chapter 8 SECTION 7: Handling and storage 7.1. Precautions for safe handling Container may burst when heated to over 50 C. The contents may form explosive, combustible mixture. Avoid ignition sources and naked flames. Comply with warming on container label. Hygiene measures: Wash hands before work breaks and after finishing work. Wash off any dirt that gets onto the skin with lots of soap and water, skin care Conditions for safe storage, including any incompatibilities For pressurized can: protect from direct sunshine and temperatures above 50 C. Keep only in the original container. Keep container tightly sealed. Do not store together with food or other consumables (coffee, tea, tobacco, etc.) Specific end use(s) Assembly adhesives SECTION 8: Exposure controls/personal protection 8.1. Control parameters Valid for Great Britain None 8.2. Exposure controls: Respiratory protection: Not needed. Hand protection: Recommended are gloves made from Nitril rubber ( Material thickness >0,1 mm, Perforation time < 30s).Gloves should be replaced after each short time contact or contamination. Available at laboratory specialized trade or at pharmacies / chemist's shops. Eye protection: Protective goggles Skin protection: Suitable protective clothing

4 UniBond No More Nails Interior Page 4 of 6 SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties Appearance paste viscous Whitish Odor little intrinsic odour ph (20 C (68 F)) Initial boiling point Flash point Decomposition temperature Vapour pressure Density (20 C (68 F)) Bulk density Viscosity (Brookfield; 20 C (68 F)) Viscosity (kinematic) Explosive properties Solubility (qualitative) (23 C (73.4 F); Solvent: Water) Solidification temperature Melting point Flammability Auto-ignition temperature Explosive limits Partition coefficient: n-octanol/water Evaporation rate Vapor density Oxidising properties 8,0-10,0 1,25-1,30 g/cm mpa.s Miscible 9.2. Other information Reactivity None if used for intended purpose Chemical stability Stable under recommended storage conditions Possibility of hazardous reactions See section reactivity Conditions to avoid None if used for intended purpose Incompatible materials None if used properly Hazardous decomposition products None known SECTION 10: Stability and reactivity Information on toxicological effects SECTION 11: Toxicological information General toxicological information: To the best of our knowledge no harmful effects are to be expected if the product is handled and used properly.

5 UniBond No More Nails Interior Page 5 of 6 General ecological information: Do not empty into drains, soil or bodies of water. SECTION 12: Ecological information SECTION 13: Disposal considerations Waste treatment methods Product disposal: Dispose of waste and residues in accordance with local authority requirements. Disposal of uncleaned packages: Use packages for recycling only when totally empty. Waste code Road transport ADR: Class: 2 Classification code: 5A Hazard ident. number: Technical name: Tunnelcode: (E) Railroad transport RID: Class: 2 Classification code: 5A Hazard ident. number: Technical name: Tunnelcode: Inland water transport ADN: Class: 2 Classification code: 5A Hazard ident. number: Technical name: Marine transport IMDG: Class: 2.2 EmS: F-D,S-U Seawater pollutant: - Proper shipping name: SECTION 14: Transport information

6 UniBond No More Nails Interior Page 6 of 6 Air transport IATA: Class: 2.2 Packaging instructions (passenger) 203 Packaging instructions (cargo) 203 Proper shipping name: Aerosols, non-flammable SECTION 15: Regulatory information Safety, health and environmental regulations/legislation specific for the substance or mixture VOC content 0,00 % (VOCV VOC regulation CH) SECTION 16: Other information Further information: This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is intended to describe our products from the point of view of safety requirements and is not intended to guarantee any particular properties.