Safety Data Sheet according to Regulation (EC) No 1907/2006

Transcription

1 Safety Data Sheet according to Regulation (EC) No 1907/2006 Loctite SI ML EDFN Page 1 of 8 sds no. : Revision: printing date: SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier Loctite SI ML EDFN 1.2. Relevant identified uses of the substance or mixture and uses advised against Intended use: Silicone adhesive 1.3. Details of the supplier of the safety data sheet Henkel Ireland Operations and Research Limited Tallaght Business Park Dublin 24 Ireland Phone: +353 ( ) Fax-no.: +353 ( ) ua-productsafety.uk@uk.henkel.com 1.4. Emergency telephone number 24 Hours Emergency Tel: +44 (0) Classification of the substance or mixture SECTION 2: Hazards identification Classification (CLP): The substance or mixture is not hazardous according to Regulation (EC) No 1272/2008 (CLP). Classification (DPD): The product is not subject to classification according to the calculation methods of the "General Classification Guideline for Preparations of the EC" as issued in the last version Label elements Label elements (CLP): Hazard statement: EUH210 Safety data sheet available on request. Label elements (CLP): The substance or mixture is not hazardous according to Regulation (EC) No 1272/2008 (CLP).

2 Loctite SI ML EDFN Page 2 of 8 Label elements (DPD): The product is not subject to classification according to the calculation methods of the "General Classification Guideline for Preparations of the EC" as issued in the last version. Additional labeling: Safety data sheet available for professional user on request Other hazards None if used properly. SECTION 3: Composition/information on ingredients Declaration of the ingredients according to CLP (EC) No 1272/2008: Hazardous components CAS-No. EC Number REACH-Reg No. content Classification < 1 % Acute toxicity 4; Oral H302 Toxic to reproduction 2 H361d Specific target organ toxicity - repeated exposure 1; Oral H372 Chronic hazards to the aquatic environment 4 H413 For full text of the H - statements and other abbreviations see section 16 "Other information". Substances without classification may have community workplace exposure limits available. Declaration of ingredients according to DPD (EC) No 1999/45: Hazardous components CAS-No. EC Number REACH-Reg No. content Classification < 1 % R53 T - Toxic; R48/25 Xn - Harmful; R22 Toxic for reproduction - category 3.; Xn - Harmful; R63 For full text of the R-Phrases indicated by codes see section 16 'Other Information'. Substances without classification may have community workplace exposure limits available Description of first aid measures SECTION 4: First aid measures Inhalation: Move to fresh air. If symptoms persist, seek medical advice. Consideration should be given to the possible effects of a faulty UV source (Stray radiation, ozone). Skin contact: Rinse with running water and soap. Seek medical advice. Eye contact: Rinse immediately with plenty of running water (for 10 minutes). Seek medical attention if necessary. Ingestion: Rinse out mouth, drink 1-2 glasses of water, do not induce vomiting. Seek medical advice Most important symptoms and effects, both acute and delayed Prolonged or repeated contact may cause skin irritation. Prolonged or repeated contact may cause eye irritation.

3 Loctite SI ML EDFN Page 3 of Indication of any immediate medical attention and special treatment needed See section: Description of first aid measures 5.1. Extinguishing media Suitable extinguishing media: water, carbon dioxide, foam, powder SECTION 5: Firefighting measures Extinguishing media which must not be used for safety reasons: None known 5.2. Special hazards arising from the substance or mixture In case of fire, keep containers cool with water spray. carbon oxides Advice for firefighters Keep unnecessary personnel away. Wear self-contained breathing apparatus. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Avoid skin and eye contact. Ensure adequate ventilation Environmental precautions Do not let product enter drains Methods and material for containment and cleaning up For small spills wipe up with paper towel and place in container for disposal. For large spills absorb onto inert absorbent material and place in sealed container for disposal. Dispose of contaminated material as waste according to Chapter Reference to other sections See advice in chapter 8 SECTION 7: Handling and storage 7.1. Precautions for safe handling Use only in well-ventilated areas. Avoid skin and eye contact. Prolonged or repeated skin contact should be avoided to minimise any risk of sensitisation. Hygiene measures: Wash hands before work breaks and after finishing work. Do not eat, drink or smoke while working. Good industrial hygiene practices should be observed Conditions for safe storage, including any incompatibilities Store in a cool, dry place. Keep container tightly sealed Specific end use(s) Silicone adhesive

4 Loctite SI ML EDFN Page 4 of 8 SECTION 8: Exposure controls/personal protection 8.1. Control parameters Occupational Exposure Limits Valid for Great Britain Ingredient ppm mg/m 3 Type Category Remarks TIN COMPOUNDS, ORGANIC, EXCEPT CYHEXATIN (ISO), (AS SN) 0,1 Time Weighted Average (TWA): EH40 WEL TIN COMPOUNDS, ORGANIC, EXCEPT CYHEXATIN (ISO), (AS SN) TIN COMPOUNDS, ORGANIC, EXCEPT CYHEXATIN (ISO), (AS SN) Skin designation: 0,2 Short Term Exposure Limit (STEL): Can be absorbed through the skin. EH40 WEL EH40 WEL Biological Exposure Indices: None 8.2. Exposure controls: Engineering controls: Ensure good ventilation/extraction. Respiratory protection: Ensure adequate ventilation. Hand protection: Chemical-resistant protective gloves (EN 374). Suitable materials for short-term contact or splashes (recommended: at least protection index 2, corresponding to > 30 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness) Suitable materials for longer, direct contact (recommended: protection index 6, corresponding to > 480 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness) This information is based on literature references and on information provided by glove manufacturers, or is derived by analogy with similar substances. Please note that in practice the working life of chemical-resistant protective gloves may be considerably shorter than the permeation time determined in accordance with EN 374 as a result of the many influencing factors (e.g. temperature). If signs of wear and tear are noticed then the gloves should be replaced. Eye protection: Eye protection should be used where there is any risk of splashing. Skin protection: Wear suitable protective clothing. SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties Appearance liquid liquid copper Odor characteristic Odour threshold ph Initial boiling point Flash point Decomposition temperature > 100 C (> 212 F)

5 Loctite SI ML EDFN Page 5 of 8 Vapour pressure Density Bulk density Viscosity Viscosity (kinematic) Explosive properties Solubility (qualitative) (20 C (68 F); Solvent: Water) Solidification temperature Melting point Flammability Auto-ignition temperature Explosive limits Partition coefficient: n-octanol/water Evaporation rate Vapor density Oxidising properties Insoluble 9.2. Other information SECTION 10: Stability and reactivity Reactivity Strong oxidizing agents Chemical stability Stable under recommended storage conditions Possibility of hazardous reactions See section reactivity Conditions to avoid Stable Incompatible materials See section reactivity Hazardous decomposition products carbon oxides Information on toxicological effects SECTION 11: Toxicological information General toxicological information: The mixture is classified based on the available hazard information for the ingredients as defined in the classification criteria for mixtures for each hazard class or differentiation in Annex I to Regulation 1272/2008/EC. Relevant available health/ecological information for the substances listed under Section 3 is provided in the following. Oral toxicity: May cause irritation to the digestive tract. Inhalative toxicity: Due to the low volatility of the product there are no hazards associated with inhalation under normal conditions of use Skin irritation: Prolonged or repeated contact may cause skin irritation. Eye irritation: May cause mild irritation to the eyes.

6 Loctite SI ML EDFN Page 6 of 8 SECTION 12: Ecological information General ecological information: The mixture is classified based on the available hazard information for the ingredients as defined in the classification criteria for mixtures for each hazard class or differentiation in Annex I to Regulation 1272/2008/EC. Relevant available health/ecological information for the substances listed under Section 3 is provided in the following Toxicity Ecotoxicity: Do not empty into drains / surface water / ground water. Hazardous components CAS-No. Value type Value Acute Toxicity Study Exposure time Species Method LC mg/l Fish OECD Guideline 203 (Fish, Acute Toxicity Test) LC mg/l Fish OECD Guideline 203 (Fish, Acute Toxicity Test) EC mg/l Daphnia Daphnia magna OECD Guideline 202 (Daphnia sp. Acute Immobilisation Test) EC mg/l Daphnia Daphnia magna OECD Guideline 202 (Daphnia sp. Acute Immobilisation Test) EC mg/l Algae OECD Guideline 201 (Alga, Growth Inhibition Test) EC mg/l Algae OECD Guideline 201 (Alga, Growth Inhibition Test) Persistence and degradability Persistence and Biodegradability: The product is not biodegradable. Hazardous components CAS-No. Result Route of Degradability application no data 0-60 % no data 0-60 % Method Bioaccumulative potential / Mobility in soil Bioaccumulative potential: No data available Results of PBT and vpvb assessment No data available Other adverse effects No data available Waste treatment methods SECTION 13: Disposal considerations

7 Loctite SI ML EDFN Page 7 of 8 Product disposal: Dispose of in accordance with local and national regulations. Disposal of uncleaned packages: After use, tubes, cartons and bottles containing residual product should be disposed of as chemically contaminated waste in an authorised legal land fill site or incinerated. Waste code waste adhesives and sealants containing organic solvents and other dangerous substances The valid EWC waste code numbers are source-related. The manufacturer is therefore unable to specify EWC waste codes for the articles or products used in the various sectors. The EWC codes listed are intended as a recommendation for users. We will be happy to advise you. SECTION 14: Transport information UN number UN proper shipping name Transport hazard class(es) Packaging group Environmental hazards Special precautions for user Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code not applicable SECTION 15: Regulatory information Safety, health and environmental regulations/legislation specific for the substance or mixture VOC content < 3 % (1999/13/EC) Chemical safety assessment A chemical safety assessment has not been carried out.

8 Loctite SI ML EDFN Page 8 of 8 SECTION 16: Other information The labelling of the product is indicated in Section 2. The full text of all abbreviations indicated by codes in this safety data sheet are as follows: R22 Harmful if swallowed. R48/25 Toxic: danger of serious damage to health by prolonged exposure if swallowed. R53 May cause long-term adverse effects in the aquatic environment. R63 Possible risk of harm to the unborn child. H302 Harmful if swallowed. H361d Suspected of damaging the unborn child. H372 Causes damage to organs through prolonged or repeated exposure. H413 May cause long lasting harmful effects to aquatic life. Further information: This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is intended to describe our products from the point of view of safety requirements and is not intended to guarantee any particular properties.