Remember that you must check your boat before every outing. Visual check of the general condition of the shoes, stretcher, etc.
|
|
- Jody Warner
- 5 years ago
- Views:
Transcription
1 Heel Restraints Visual check of the general condition of the shoes, stretcher, etc. Each heel to be restrained to prevent it from rising higher than 7cm, as measured at right angles from the footplate. Furthermore, the heel restraint should be in working order and the foot release must be selfacting and not require the intervention of the athlete or a rescuer. Taking each shoe in turn: Check that its restraint is independent of the other shoe, Holding the shoe underneath the heel, give it a sharp tug upwards (simply lifting it gently is not sufficient) and check the restraint holds firm, Confirm that the heel does not rise above 7cm. Adjust accordingly. If each crew member checks their own shoes, this should take only a few seconds before the outing. Don't skip it. If in doubt ask a Coach, the Club Safety Adviser, an Umpire... If a heel restraint breaks due to excessive wear, replace it, don't just tie a knot in it and hope for the best. The odds are that the rest of the material is in a similar rotten state to the bit that broke - mend it properly - Bodge it, and you'll be mending it every time you go out.
2 Heel Restraints Lowest fixing point of shoe 5 to 7cm The future?
3 Bow Balls The bows of racing / training boats shall be properly protected. A solid ball of not less than 4 cm diameter made of rubber or material of similar resilience must be firmly attached to the bows. Where the construction of the boat, or its composition is such that the bow is properly protected, or its shape does not present a hazard in collision, this requirement need not apply. Before any outing is undertaken, equipment should be checked to ensure that it is in safe condition and in working order. Check that the bow ball is securely fixed and fully covers the bow of the boat in order that adequate protection is given to any person or object struck by the moving boat. This check should also examine any fixing screws or bolts to ensure that they do not represent a further hazard in the event of accident.
4 Buoyancy Buoyancy compartments must be watertight to ensure effective operation. Boats constructed after 1st April 2003 must have inherent buoyancy sufficient, together with their oars and sculls, to support a seated crew of the correct design weight in the event of being swamped. Boats must be labelled with design weight and build information. Check for hull damage, leaks etc. Check that buoyancy compartments, seals, hatch covers and ventilation bungs are secure and watertight. Where holes have been drilled, e.g. for speaker cables, make sure the holes have been adequately filled afterwards.
5 Riggers Check riggers, gates, swivels and pins. Check fixing to boat, if lose, tighten, but not so tight the bolts sheer or deform. Front Stay Back Stay Locking Nut Gate Top Nut Washers Main Stay Pin Swivel
6 Blades Check blade, shaft, collar and handles for damage. Check blade, shaft, collar and handles are not lose.
7 Steering Fins, Rudders, Feet, Cox Check you have a fin, that it is in place and not lose. If the boat has steering: Check the operation left and right Check the rubber is not bent or catches Check the steering wires Check the connections Check the steering feet Check the coxing handle/s.
8 Seats & Runners Check you have a seat and it is the correct one for the boat Check the runners are tight and in the right place Check correct operation of seat with / without weight on it wheels rotation, seat action - single/double Check and tape any sharp ends likely to cut the calves
9 Floats and Height Check floats are not damaged Check floats are at correct height and secure
10 Quick Check Check riggers, gates, swivels and pins. Check rigger fixing. Check shoes and heel restraints. Check the Foot Stretcher fixing. Check the Seat and Runners. Check Buoyancy Compartments. Check Shell. Check Bow Ball.
Notes for preparing MRC boats for transport to/from Regattas
Notes for preparing MRC boats for transport to/from Regattas 1. Aim of the training: To safely move boats and other MRC equipment to and from regattas without loss of equipment, nuts, washers etc. and
More informationPROBLEM? Coaches are not only concerned with coaching crews; they have an underlying responsibility for crew
EQUIPMENT CHECKS KAT ASTLEY CHRIST S COLLEGE BOATMAN -And ex-irresponsible college rower! - IS EQUIPMENT YOUR PROBLEM? Yes! ARA states clearly: Coaches are not only concerned with coaching crews; they
More information1 Basic Rigging. 1.1 Introduction. 1.2 Measuring aids and tools. 1.3 Terminology
1 Basic Rigging Basic Rigging 1.1 Introduction Rowing is a sport that requires concerted motion between the athlete and the boat. To row effectively and to learn correct technique, it is clear that the
More informationRiggers and Associated Parts
Riggers and Associated Parts Pins are all 13mm shafts, with 8x27mm tops, and supplied with washers, nuts and spacers. Rig 1A-sc 13x105mm shaft, 10x55mm base - for scull & sweep Carbon wing S/S yes 28.57
More informationRowing Terminology. The person at the starting dock who aligns the boats evenly for a fair start.
Rowing Terminology ALIGNER BACK ARM BACK CHOCKS BLADE BOW BOW(MAN) BOW BALL BOW SIDE BUTTON CANVAS CATCH CHECK IT COCKPIT The person at the starting dock who aligns the boats evenly for a fair start. Supports
More informationMethylethycetone (MEC) - PMS 60 polyurethane glue - Grease - White silicone
CHAPTER PLAN page : 1/8 SAILING BOAT SUSPENDED WITHOUT DECK BEARING SAILING BOAT SUSPENDED WITH DECK BEARING SAILING BOAT SUSPENDED WITH AUTOMATIC BEARING ALIGNMENT RUDDER SYSTEM FOR ANTARES MOTOR BOAT
More informationRow Safe Example Gap Analysis Check Sheet
Row Safe Example Gap Analysis Check Sheet This sheet has been produced for clubs to help them check and develop their safety systems in conjunction with the ARA s Row Safe: A guide to good practice in
More informationAssembly Instructions. -Cantilever Boat Lifts
Assembly Instructions -Cantilever Boat Lifts Winch Instruction Page Safety Information 1. The winch is built for the multipurpose of hauling and lifting operations. It is not to be used as a hoist for
More informationPeinert Dolphin. Assembly
Peinert Dolphin Assembly The Dolphin is easily rigged; there are only four removable parts - the seat, the foot stretcher, the rigger arm, and the fin. Removal and installation of the seat. If the seat
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO KAYAKS IMPORTANT: Tandem models will require the Wildy Supplemental kit in addition to this kit. The Supplemental kit provides extension straps and extra footbraces that allow rudder positioning
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO AND TANDEM KAYAKS IMPORTANT: For Tandem kayaks, the Supplemental Kit will be needed in addition to this kit and can be purchased through a registered dealer. The addition of a rudder to
More informationRudder Kit Assembly Instructions for Quest 13
Rudder Kit Assembly Instructions for Quest 13 Revised 4/2/2015 78501 Rudder System The Hobie Quest is designed for the addition of an optional rudder system. Rudder systems in boats like this allow you
More informationIntroduction to Rowing Lingo
Introduction to Rowing Lingo These sections will describe the process and terms used to move the shell from the boathouse to the water, as well as getting through your first day on the water... Commands
More informationINSTALLING THE TRIDENT 11, 13 OR 15 RUDDER
INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 - Rubber 2 - Rail Assemblies 1 - Rudder Body 1 - Rudder Retraction Grommets
More informationAppendix Aggie Crew Operating Procedures
Revised 8/31/13 Appendix Aggie Crew Operating Procedures Contents 1. Pre-requisites for Aggie Crew Team... 2 2. Reporting and Communications... 4 3. Aggie Crew Safe Practice Requirements... 5 4. Requirements
More informationPortlight Construction
Portlight Construction Version 2, dated 28 th June 2012 Contents Opening Portlights - Requirements... 2 Opening Portlights Design Parameters... 2 An Opening Portlight Design... 3 Making the Opening Portlight
More informationTable of content Introduction 5 1. Part 1. Assembly Tools needed for Assembly Glossary Hulls Mounting the beams 7
Table of content Introduction 5 1. Part 1. Assembly 6 1.1. Tools needed for Assembly 6 1.2. Glossary 6 1.3. Hulls 7 1.3.1. Mounting the beams 7 1.3.2. Fixing the mast rotation cleats 8 1.3.3. Placing the
More informationINSTALLING THE PROWLER 13 RUDDER
INSTALLING THE PROWLER 13 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 Rubber 2 Rail Assemblies Rudder Body 1 Rudder Retraction Grommets (includes steering
More informationIn each step, the needed parts are shown the number right below. Locate all parts for the step.
Tools Required for Assembly Phillips Screwdriver, Med Needle Nose Pliers Sandpaper (#400 grit) Hobby Knife Scissors CA Instant Glue Rubbing Alcohol Drill Bit 1/16", 1.6mm 5/64, 2mm 1/8, 3mm 5/32, 4mm Before
More informationSHEET 2: VERTICAL INSTALLATION
IMAGE OW1291 OW1293 OW1295 OW1297 AVATAR OW1301 OW1303 OW1305 OW1307 OW1311 OW1313 OW1315 OW1317 OW1331 OW1333 OW1335 OW1337 SHEET 2: VERTICAL INSTALLATION SHEET 3: HORIZONTAL INSTALLATION Drawing: 760883XX
More informationGlossary of Rowing Terms
Glossary of Rowing Terms Backsplash: The water thrown back towards the bow by the oar's blade as it enters the water during a catch. A proper catch should throw a small amount of water Blade: Another term
More informationINSTALLING YOUR CLC RUDDER
INSTALLING YOUR CLC RUDDER These instructions are written to help you install the CLC rudder kit on your wooden kayak. The rudder can be fitted to your boat during construction or after completion. Please
More informationAPPENDIX 5. Bye-Laws to Rule 50 of the FISA Rules of Racing Advertising Bye-Laws
APPENDIX 5 Bye-Laws to Rule 50 of the FISA Rules of Racing 1. Application of these Rules These bye-laws apply to all international regattas governed by FISA rules. In addition, certain sections below describe
More informationBoat Boat Loader Fitting Instructions
Aerodynamic & Heavy Duty Roof Rack Systems Australian Made - Australian Owned www.rhinorack.com Boat Boat Loader Fitting Instructions CONTROLLED Balance point 3 Front eye nuts position 3 Transom eye nut
More informationRUDDER KIT INSTRUCTIONS
C I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS PAMLICOS-0,0,T, T, 60T, Excel Rotomolded Pamlico 0, 0, T, T, 60T, Excel The addition of a rudder to a kayak results in additional control and efficiency,
More informationLearn To Row (LTR) Handbook
Rowing since 2005 Learn To Row (LTR) Handbook Thanks to the Department of National Parks, Recreation, Sport and Racing Active Inclusion Program for assistance to print this handbook. Riverway Rowing Club
More informationA Basic Guide to Europe Dinghy Rigging
The Basics: A Basic Guide to Europe Dinghy Rigging Use the smallest blocks available for the line size. Most of the blocks on your boat will be micro blocks. Examine all of your rigging and ensure that
More informationSTERN MOTOR FOOT CONTROL KIT For use with the Torqeedo 403 Ultralight
STERN MOTOR FOOT CONTROL KIT For use with the Torqeedo 403 Ultralight The Wilderness Systems Foot Control Kit is designed to connect directly to a Torqeedo 403 Ultralight motor mounted on the stern of
More informationIMPORTANT: RECEIVING INSTRUCTIONS:
Instruction Sheet Sidewinder Mechanical Bender IMPORTANT: RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any shipping damage is found, notify carrier at once.shipping damage
More information3. Fit. 1 Owner s manual
3. Fit NOTE: Correct fit is an essential element of bicycling safety, performance and comfort. Making the adjustments to your bicycle which result in correct fit for your body and riding conditions requires
More informationPeinert ZEPHYR. Assembly. The Zephyr is easily rigged; there are only three removable parts - the seat, the foot stretcher, and the rigger arm.
Peinert ZEPHYR Assembly The Zephyr is easily rigged; there are only three removable parts - the seat, the foot stretcher, and the rigger arm. Removal and installation of the seat. If the seat is in the
More informationInstallation Instructions MODEL VSTI-A020 Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Versa Steel Inc. Guide Cables No
Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Guide Cables No Guide Cables 1 August 4, 2011 Assembly Instructions: (Shown with a 2 board, 12 ft kit) ITEM NO. PART NUMBER DESCRIPTION
More informationRST INSTRUMENTS LTD.
RST INSTRUMENTS LTD. Borehole Packers Instruction Manual Copyright 2016 Ltd. All Rights Reserved Ltd. 11545 Kingston St., Maple Ridge, B.C. Canada V2X 0Z5 Tel: (604) 540-1100 Fax: (604) 540-1005 Email:
More informationASSEMBLY MANUAL HOBIE CATSY
ASSEMBLY MANUAL HOBIE CATSY HOBIE CAT EUROPE ZI Toulon Est, BP 50 8078 Toulon cedex 9, France Tel : + (0)9 08 78 78 - Fax : + (0)9 08 99 Email : hobiecat@hobie-cat.net - http://www.hobie-cat.net ASSEMBLY
More informationRef Part Part # Qty Letter A Rudder Catcher B X 1/2 PH Bolts C Rudder Bracket
Ref Part Part # Qty A Rudder Catcher 07.2694.0000 1 J B Q A B 10-32 X 1/2 PH Bolts 07.2136.0000 10 C Rudder Bracket 07.2689.0000 1 D Kayak Pad Eye 01.1315.0430 2 E Cherry Rivets 01.1315.0459 4 H T N P
More informationStep 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the seam joint is.
WhiplashGV Instruction Manual Email: Brian@Blazermarine.com Phone: 513-598-1769 Step 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the
More informationTable of content Introduction 5 1. Part 1. Assembly 6 1.1. Tools needed for Assembly 6 1.2. Glossary 6 1.3. Hulls 7 1.3.1. Mounting the beams 7 1.3.2. Fixing the mast rotation cleats 8 1.3.3. Mounting
More informationULTIMATE 12 RUDDER INSTALLATION INSTRUCTIONS
ULTIMATE 12 RUDDER INSTALLATION INSTRUCTIONS TOOLS NEEDED: DRILL ¼ DRILL BIT ¾ HOLE SAW 3/16 DRILL BIT PHILLIPS HEAD SCREWDRIVER 7/16 WRENCH HEAT SOURCE: PROPANE TORCH, LIGHTER OR HOT AIR GUN WIRE CUTTER
More informationADULT LEARN TO ROW PROGRAM. Coxswain s Handbook
ADULT LEARN TO ROW PROGRAM Coxswain s Handbook At some point in your Learn to Row class, you will be asked to be the coxswain for your crew. The first time is always pretty scary. Follow the instructions
More informationPanoptix PS51-TH FrontVü/LiveVü Thruhull
Panoptix PS51-TH FrontVü/LiveVü Thruhull Transducer Installation Instructions Important Safety Information WARNING See the Important Safety and Product Information guide in the chartplotter or fishfinder
More informationQUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift
INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your
More informationOPPI Rigging Guide 3/2008
OPPI Rigging Guide 3/2008 McLaughlin Boat Works optistuff.com Thanks for purchasing OPPI, the most durable and F-U-N sailboat available. Rigging your OPPI is easy and the following pictures make it a breeze
More informationIndex 1. Trampoline 2. Main Foils 3. Spinnaker Pole 4. Mast Setup 5. Mast Rigging 6. Rig Tension 7. Trapeze Lines 8. Rudders 9. Boom 10. Main Sheet an
By User Manual Index 1. Trampoline 2. Main Foils 3. Spinnaker Pole 4. Mast Setup 5. Mast Rigging 6. Rig Tension 7. Trapeze Lines 8. Rudders 9. Boom 10. Main Sheet and Traveler 11. Main Sail 12. Downhaul
More informationRUDDER KIT INSTRUCTIONS
A I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS TARPON 0/40/60/60i The Tarpon series is designed as a high performance sit-on-top kayak tailored for the sport paddler. Our rudder system is designed to
More informationDepth sensor. Product reference : REV 1. USER GUIDE and INSTALLATION GUIDE. nke Sailing competition
Depth sensor Product reference : 90-60-456 REV 1 USER GUIDE and INSTALLATION GUIDE nke Sailing competition Z.I. Kerandré Rue Gutenberg 56700 HENNEBONT- FRANCE http://www.nke.fr After sale service n 33
More informationInstallation and Training Manual
AirForce1 Tower Kit Installation and Training Manual FuturEnergy Limited Ettington Park Business Centre Stratford upon Avon CV37 8BT +44 (0)1789 451070 Table of Contents Safety Notes... 3 Parts Supplied
More informationASSEMBLY INSTRUCTIONS
XR 9-2009:new odc 1018 revised 2/17/10 9:11 AM Page 1 ODC XR 9 OUTDOOR DISCOVERY CRAFT ASSEMBLY INSTRUCTIONS Your ODC XR 9 Pontoon Boat comes in two separate cartons consisting of the following parts:
More informationTopaz OMEGA Rigging Instructions
Topaz OMEGA Rigging Instructions www.toppersailboats.com TOPAZ OMEGA RIGGING INSTRUCTIONS CONTENTS 02. Introduction 02. Manufacturers Details 03. Maintenance 04. Raising the Mast 05. Attaching the Boom
More information2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions
SECTION A: INTRODUCTION This unofficial set of installation instructions was written for a 2009 Hobie Getaway, using a 2012 Hobie Spinnaker Kit 20999020. Note from the Author: I had never seen this kit
More informationPage 1. Single Scull Car Rack Assembly and User s Manual " "
Page 1 Single Scull Car Rack Assembly and User s Manual Page 2 Items in the box: (2) V cradles (2) 4 rails (1) 1 3/4 X 18 rail coupler (4) 1/4-20 X 4 1/2 bolts (2) 1/4-20 X 2 1/2 bolts (12) 1/4 flat washers
More informationHead of the Don Doncaster, Sunday 7 th October 2018 Competitor Instructions
Head of the Don Doncaster, Sunday 7 th October 2018 Competitor Instructions The following is intended to make your visit to the Head of the Don easy and enjoyable and includes guidelines that are in place
More informationM32 CATAMARAN ASSEMBLY MANUAL
M32 CATAMARAN ASSEMBLY MANUAL 1 M32 CATAMARAN ASSEMBLY MANUAL MANUAL SUMMARY M32 ASSEMBLY Parts and tools Instructions MAST PLATFORM Parts and tools Instructions MAST STEPPING Instructions MAIN HALYARD
More informationBladerider X8 Assembly Help Notes
2.1 Remove All Parts & Have Some Tools Handy Remove all items from the box and identify each part as per the packing sheet and check that nothing is missing. If there is something missing, please email
More information8. Carefully layout all the parts of the reservoir setup and clean any dirt, grime or dust from the parts. ( image 8 ) 8
INSTRUCTIONS TO SERVICE AMADAXTREME SHOCKS 2.0 REMOTE RES AUSTRALIAN VERSION PART 1 - SERVICE THE RESERVOIR 1.Prior to cleaning the shock check for any leaks or signs of damage to the res, lines, bushes
More informationTUNE YOUR SAILS SPEED. Optimist Tuning Guide. Photo Wavelength
TUNE YOUR SAILS FOR OUTRIGHT SPEED Photo Wavelength PEAK / HEAD THROAT TACK CLEW THANK YOU for choosing North Sails for your Optimist. Whether you are just starting out in an Optimist you are an experienced
More informationEZee Glider Manual. Tools needed for Assembly: Wrench (included) Philips Screwdriver (not included) Assembly Instructions
EZee Glider Manual Congratulations on your purchase of the EZee Glider! Your glider is designed for years of nearly carefree use by your child. These instructions include how to set up your glider and
More informationUsing Dividing Plates with the Rotary Table
The premier source of parts and accessories for mini lathes and mini mills. Using Dividing Plates with the Rotary Table Dividing plates allow you to precisely divide a circle into a number of divisions
More informationINDOOR CYCLING BIKE SF-B1110 USER MANUAL
INDOOR CYCLING BIKE SF-B1110 USER MANUAL IMPORTANT! Read all instructions carefully before using this product. Retain owner s manual for future reference. For customer service, please contact: support@sunnyhealthfitness.com
More informationThank you for purchasing a WIKE BOX BIKE!
Thank you for purchasing a WIKE BOX BIKE! Contents Safety.....3 Front wheel.4 Kickstand..5 Handle Bar & Box 6 Seat post and Saddle 7 Final pre-ride check 8 Tools needed to assemble Bike: -High table or
More information400/488 Rotating Davit Installation Instructions
400/488 Rotating Davit Installation Instructions These instructions were written with the owner in mind. If you are the installer make sure these instructions are passed along to the owner of the boat.
More informationBoat Registration Form
Port Washington Pirate Festival Boat Registration Form Registration Type Entry Fee Per Boat $25 must be paid by May 1 st, 2018 Awards: 1st Place Fastest time around course (per division/per Design Type
More information2011 RowWing ASSEMBLY INSTRUCTIONS. Congratulations on your purchase of a RowWing!
2011 RowWing ASSEMBLY INSTRUCTIONS Congratulations on your purchase of a RowWing! STERN BOW 1. Monorail 2. Rigger Wing 3. Port Oarlock 4. Port Stern Stay 5. Stern Stay Tower 6. Piantedosi Decal 7. Port
More informationTrike-Bike Assembly Manual
Be sure to check our website for more instruction details, videos and photographs as well as a complete listing of each Nut and Bolt for the Trike Bike. www.trike-bike.com.au Go to the page marked ASSEMBLY
More informationPT 11 trouble-shooting and maintenance.
PT 11 trouble-shooting and maintenance. Does your rudder not stay down?...your back seat slip off?...your knobs tight and your leather pads loose? Maybe we can help. We have used our PT 11 s hard enough
More informationATD /8 x 50 Retractable Air Hose Reel Owner s Manual
ATD-31166 3/8 x 50 Retractable Air Hose Reel Owner s Manual Features Heavy-gauge, all-steel reel assembly 8-position ratchet mechanism locks reel at desired hose length 5-position adjustable roller outlet
More informationSEADUCER BOATS GAS SPORT HYDRO
SEADUCER BOATS GAS SPORT HYDRO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 2 - Pkg. Of 440 push rod ends 2 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 30" flex
More informationNo.5550 INTRUCTION MANUAL WARRANTY WARNING. Notice This is not a toy. Assembly and operating of this boat requires adult supervision.
INTRUCTION MANUAL WARRANTY Thunder Tiger guarantees this model kit to be free from defects in both material and workmanship. The total monetary value under warrant will in no case exceed the cost of the
More informationA-FRAME RESIN IN & OUT FLIP UP LADDER
A-FRAME RESIN IN & OUT FLIP UP LADDER NE1222 NOTE FOR SAFETY PURPOSES ALL LADDERS SHOULD BE SECURED BY ATTACHING THEM TO THE TOP LEDGE OF THE POOL. (See step 13 for details) In order for the ladder to
More informationPico rigging manual 2007.doc Page 1 of 28
Pico rigging manual 2007.doc Page 1 of 28 Pico Rigging Instructions The Pico rigging instructions are a guide to rigging your boat. Due to production supplies certain parts may be slightly modified from
More informationFISA Rule Book 2018 Proposed Amendments to Appendices only except for Anti Doping version
APPENDIX 10 BYE-LAWS TO RULES 42 TO 44 REGATTA COURSES 2.3 Width of Water The standard international course shall be at least 108 m wide i.e. 13.5 m + (6 lanes x 13.5 m each) + 13.5 m = 108 m. The minimum
More informationGuide of the BrickIt balloon system for LEGO Blimps
Guide of the BrickIt balloon system for LEGO Blimps Introduction At LEGO WORLD Zwolle 2010 we saw the blades on the LEGO Education Renewable Energy Add-On Set 9688 for the first time (See Figure 1). We
More informationUser Manual. User Manual
Thank you Thank you for buying RGK We hope the product and service you have received has met your expectations. Please take time to read the instructions contained within, to familiarise yourself with
More informationCRYOGENIC TANK SERVICES - CHART RECORDER MANUAL
CRYOGENIC TANK SERVICES - CHART RECORDER MANUAL Pressure Chart Recorder / Temperature Chart Recorder / Dual Recorder Portable Mechanical Chart Recorder for the accurate measurement and recording of Pressure
More informationBELT DRIVE INDOOR CYCLING BIKE SF-B1712 USER MANUAL
BELT DRIVE INDOOR CYCLING BIKE SF-B1712 USER MANUAL IMPORTANT! Please retain owner s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN
More informationTroyer s Gourd Rack 8 unit F R H O P
B E A D I M-N L Vertical Parts F R H O P Horizontal Parts C G J Updated 11/16 Parts List A: Top of Pole B: Bottom of Pole C: 48 Ground Stake D: Top Perch rods 48 long E: Hub F: Rope Winder w/ attached
More informationKMX Kompact Sports Trike
KMX Kompact Sports Trike Assembly Instructions 1.0 Introduction Thank you for choosing KMX! When properly assembled and set up your KMX will provide many years of enjoyment. KMX Karts Ltd does its utmost
More informationMini Glider Manual. Your Glider comes partially assembled. The front wheel and the handlebars require assembly.
Mini Glider Manual Congratulations on your purchase of the Mini Glider! Your glider is designed for years of nearly carefree use by your child. These instructions include how to set up your glider and
More informationAssembly Instructions And User Guide
EZ-1/EZ-CLASSIC QUADRIBENT By Blackbird Designs Inc. Mark 5.2 June 2011 Assembly Instructions And User Guide 1 The Quadribent is 2-seat, side-by-side, human powered vehicle that enables almost anyone to
More informationFinal Assembly Instructions Bikes with Threaded Headsets
Final Assembly Instructions Bikes with Threaded Headsets Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our
More informationLadies Shopper Bike Assembly Manual 28C03
Ladies Shopper Bike Assembly Manual 28C03 Ecosmo Ltd 1 Know your bike 1. Wheel 2. Rear Derailleur 3. Chain 4. Crank Set 5. Pedal 6. Seat Quick Lock 7. Saddle and Post 8. Frame 9. Front Light 10. Front
More informationIMPORTANT PLEASE READ BEFORE COMMENCING INSTALLATION
IMPORTANT PLEASE READ BEFORE COMMENCING INSTALLATION This Fitting Guide is designed to assist in the Installation of your Reverse Osmosis System. Some of the parts that are supplied with each system may
More information7130 Lancer Rear Drive Magnetic Commercial Indoor Cycling Bike
7130 Lancer Rear Drive Magnetic Commercial Indoor Cycling Bike Owner s Manual Made in Taiwan INDEX IMPORTANT SAFETY INFORMATION... 1 EXPLODED DRAWING... 2 PARTS LIST... 3 ASSEMBLY INSTRUCTION... 4-9 USER
More informationBC Shackle. Made in the China. Alloy Steel Anchor Shackle. Instructions for handling and use - Please read in full before using this device
BC Shackle Made in the China Alloy Steel Anchor Shackle Instructions for handling and use - Please read in full before using this device Index 1.) Introduction 2.) Warnings / General Use Guidelines 3.)
More informationA. TO PREPARE THE MACHINE FOR USE.
INSTRUCTION MANUAL FOR THE ML120 STRINGING MACHINE. CONTENTS: A. TO PREPARE THE MACHINE FOR USE. 1. The assembly of frame with console and tooltray. 2. Fixing the lever of the tension unit. 3. Putting
More information1982 Hydrostream Viking Restoration
1982 Hydrostream Viking Restoration Part 2c: The Rebuild Daniel W. Rickey Winnipeg, Manitoba Canada daniel@cancercare.mb.ca 2000-09-22 Introduction Part one of this report showed how the shoddy manufacturing
More informationRiviera Draft Shaft Hole Boring
Riviera Draft Shaft Hole Boring a. Height from bottom of hull thru the hull to the center of the drive shaft. This will be calculated. b. Height of drop of strut. The strut for the Riviera is 7.5 c. Distance
More informationLower Boats Captains Course
Cambridge University Combined Boat Clubs Lower Boats Captains Course Dan Wilkins CUCBC Honorary Secretary and Deputy Chief Umpire of the Bumps Overview Useful information from CUCBC Rules of the River
More informationMODEL / SINGLE and DUPLEX PULLEY SYSTEMS
MODEL 922181/922182 SINGLE and DUPLEX PULLEY SYSTEMS MODEL 922181 SINGLE PULLEY SYSTEM MODEL 922182 DUPLEX PULLEY SYSTEM 1 PARTS LIST FOR SINGLE/DUPLEX COLUMN PULLEYS Note: Check with your architect or
More informationLIQUIP DRYBREAK COUPLER. API800 Series MAINTENANCE INSTRUCTIONS
LIQUIP DRYBREAK COUPLER API800 Series MAINTENANCE INSTRUCTIONS API LOADING COUPLER TO API RP1004 June 2015 Issue: F M:\Product-Info\API8xx\6-Service-Maintenance\API800 MAINTENANCE INSTRUCTIONS 40183.doc
More informationCRUZBIKE Quest 2.0 Assembly
CRUZBIKE Quest 2.0 Assembly CRUZBIKE Quest 2.0 Assembly... 1 General notes on assembly... 2 Un box and evaluate the frame and major parts... 2 Unfold the rear swing arm and arrange the frame... 3 Rear
More informationTHE SCHOOLS HEAD OF THE RIVER RACE INSTRUCTIONS FOR COACHES, COXSWAINS AND STEERS And this does mean all of you!
THE SCHOOLS HEAD OF THE RIVER RACE 2018 Monday 12 th March - START TIME 13:00 INSTRUCTIONS FOR COACHES, COXSWAINS AND STEERS And this does mean all of you! This year s the race should be run from the usual
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More informationINDEX. Specifications 1. Important Safety Precautions 2. Operating Instructions 3, 4. Optional Extras (Meal Tray & Footrest) 5.
INDEX Specifications 1 Important Safety Precautions 2 Operating Instructions 3, 4 Optional Extras (Meal Tray & Footrest) 5 Air System 6 Service & Maintenance 7 Warranty / Service Contract 8 SPECIFICATIONS
More informationUser Manual Important, read before use!
EN User Manual Important, read before use! SMART Congratulations on your new rollator! Volaris Smart The Volaris Smart will make your life easier in many ways. We ask you to read carefully through this
More informationSEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT
SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 1 - Pkg. Of 440 push rod ends 1 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 24" flex shaft
More informationINSTALLATION INSTRUCTIONS. Parts List. Tools Required. Before You Begin. Installation. Customer Information BICYCLE ATTACHMENT JUL.
INSTALLATION INSTRUCTIONS JUL. 2006 Parts List Bicycle attachment Key plates (2) Tools Required Phillips screwdriver Flat-tip screwdriver Before You Begin Customer Information This Bicycle Attachment is
More informationMAGNETIC INDOOR CYCLING BIKE
MAGNETIC INDOOR CYCLING BIKE SF-B1805 USER MANUAL IMPORTANT! Please retain owner s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL
More informationBR-2444 ROWING MACHINE
BR-2444 ROWING MACHINE Important Safety Information Please keep this manual in a safe place for reference. 1. It is important to read this entire manual before assembling and using the equipment. Safe
More informationVERSA BIKE RACK INSTRUCTIONS
VERSA BIKE RACK INSTRUCTIONS Models #8, 8 Important This rack is designed for use with a or. receiver hitch. The rack is designed to hold a maximum of two bicycles. Do not use it for anything other than
More informationKari-Tek. Kari-Tek. Hydro Skeg Retro-Fitting Instructions. Instructions for retro-fitting of Hydro Skeg
Kari-Tek Instructions for retro-fitting of Hydro Skeg A good knowledge of fibreglassing will be required to fit the Hydro Skeg successfully. When working with fibreglass and cutting the holes, safety glasses,
More information