The Personal Formulator Safety Data Sheet

Transcription

1 Product Name: Isododecane Section 1 Product and Company Identification Personalformulator.com 97 S. Red Willow Rd. Evanston, WY Revision date: January 1, 2014 Supersedes: Product Name: Isododecane CAS No For Chemical Emergency, 24 hours, 7 days, Call: InfoTrac Section 2 - Hazardous Identification Flammable. Harmful: may cause lung damage if swallowed. Danger Flammable liquid and vapor. May be fatal if swallowed and enters airways. IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician. Do NOT induce vomiting. Section 3 - COMPOSITION / INFORMATION ON INGREDIENTS Substances Formula : Molecular Weight: C12H26 170,33 g/mol Isododecane CAS-No EC-No Section 4 - FIRST AID MEASURES General advice Consult a physician. Show this safety data sheet to the doctor in attendance. If inhaled If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a physician. In case of skin contact Wash off with soap and plenty of water. Consult a physician. In case of eye contact Flush eyes with water as a precaution. If swallowed Do NOT induce vomiting. Never give anything by mouth to an unconscious person. Rinse mouth with water. Consult a physician. Most important symptoms and effects, both acute and delayed To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated. I s o d o d e c a n e - R e v i si o n D a y : J a n u a r y 1, P a g e 1 5

2 Section 5 - FIRE FIGHTING MEASURES Suitable extinguishing media For small (incipient) fires, use media such as "alcohol" foam, dry chemical, or carbon dioxide. For large fires, apply water from as far as possible. Use very large quantities (flooding) of water applied as a mist or spray; solid streams of water may be ineffective. Cool all affected containers with flooding quantities of water. Special hazards arising from the substance or mixture: Carbon oxides Advice for firefighters Wear self-contained breathing apparatus for firefighting if necessary. Further information Use water spray to cool unopened containers. Section 6 - ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures Use personal protective equipment. Avoid breathing vapors, mist or gas. Ensure adequate ventilation. Remove all sources of ignition. Evacuate personnel to safe areas. Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low areas. Environmental precautions Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Discharge into the environment must be avoided. Methods and materials for containment and cleaning up Contain spillage, and then collect with an electrically protected vacuum cleaner or by wet-brushing and place in container for disposal according to local regulations (see section 13). Section 7 - HANDLING AND STORAGE Precautions for safe handling Avoid contact with skin and eyes. Avoid inhalation of vapor or mist. Keep away from sources of ignition - No smoking. Take measures to prevent the buildup of electrostatic charge. Conditions for safe storage, including any incompatibilities Store in cool place. Keep container tightly closed in a dry and well-ventilated place. Containers which are opened must be carefully resealed and kept upright to prevent leakage. Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION Exposure controls Appropriate engineering controls Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday. Personal protective equipment Eye/face protection Face shield and safety glasses Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Skin protection I s o d o d e c a n e - R e v i si o n D a y : J a n u a r y 1, P a g e 2 5

3 Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands. The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the standard EN 374 derived from it. Immersion protection Material: Nitrile rubber Minimum layer thickness: 0,4 mm Break through time: > 480 min Material tested:camatril? ( Z677442, Size M) Splash protection Material: Nitrile rubber Minimum layer thickness: 0,11 mm Break through time: > 30 min Material tested:dermatril? ( Z677272, Size M) data source: KCL GmbH, D Eichenzell, phone +49 (0) , sales@kcl.de, test method: EN374 If used in solution, or mixed with other substances, and under conditions which differ from EN 374, contact the supplier of the CE approved gloves. This recommendation is advisory only and must be evaluated by an Industrial Hygienist familiar with the specific situation of anticipated use by our customers. It should not be construed as offering an approval for any specific use scenario. Body Protection Complete suit protecting against chemicals, Flame retardant antistatic protective clothing, The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace. Respiratory protection Where risk assessment shows air-purifying respirators are appropriate use a full-face respirator with multi-purpose combination (US) or type ABEK (EN 14387) respirator cartridges as a backup to engineering controls. If the respirator is the sole means of protection, use a full-face supplied air respirator. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU). Section 9 - PHYSICAL AND CHEMICAL PROPERTIES Appearance Form Liquid Odor Odor Threshold ph Melting point/freezing point Initial boiling point/boiling range Flash point 180 C at hpa Evaporation rate 37 C - closed cup Color colorless Flammability (solid, gas) Vapour pressure 56,333 hpa at 65 C Vapour density Relative density 0,745 g/cm3 Water solubility insoluble Decomposition temperature Viscosity Explosive properties Oxidizing properties The above data are typical values and do not constitute a specification. Vapor pressure data are calculated unless otherwise noted. I s o d o d e c a n e - R e v i si o n D a y : J a n u a r y 1, P a g e 3 5

4 Section 10 - STABILITY AND REACTIVITY Reactivity Chemical stability Possibility of hazardous reactions Conditions to avoid Incompatible materials Heat, flames and sparks. Section 11 - TOXICOLOGICAL INFORMATION Information on toxicological effects Acute toxicity Skin corrosion/irritation Serious eye damage/eye irritation Respiratory or skin sensitization Germ cell mutagenicity Carcinogenicity IARC: No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC. Reproductive toxicity Specific target organ toxicity - single exposure Specific target organ toxicity - repeated exposure Aspiration hazard The substance or mixture is known to cause human aspiration toxicity hazards or has to be regarded as if it causes a human aspiration toxicity hazard. Potential health effects Inhalation May be harmful if inhaled. May cause respiratory tract irritation. Ingestion May be harmful if swallowed. Aspiration hazard if swallowed - can enter lungs and cause damage. Skin May be harmful if absorbed through skin. May cause skin irritation. Eyes May cause eye irritation. Signs and Symptoms of Exposure To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated. Section 12 - ECOLOGICAL INFORMATION Toxicity Persistence and degradability Bioaccumulative potential Mobility in soil Results of PBT and vpvb assessment Other adverse effects I s o d o d e c a n e - R e v i si o n D a y : J a n u a r y 1, P a g e 4 5

5 Section 13 - DISPOSAL CONSIDERATIONS Product Contaminated packaging Burn in a chemical incinerator equipped with an afterburner and scrubber but exert extra care in igniting as this material is highly flammable. Offer surplus and non-recyclable solutions to a licensed disposal company. Contact a licensed professional waste disposal service to dispose of this material. Dispose of as unused product. Section 14 - TRANSPORT INFORMATION ICAO/IATA I ICAO/IATA II IMDG IMDG EMS Fire IMDG EMS Spill IMDG MFAG MARPOL Annex II Not determined. USCG Compatibility Not determined. U.S. DOT Non-Bulk U.S. DOT Non-Bulk NAERG Canada Mexico Review classification requirements before shipping materials at elevated temperatures. Section 15 - REGULATORY INFORMATION Safety, health and environmental regulations/legislation specific for the substance or mixture Chemical Safety Assessment Section 16 - OTHER INFORMATION SDS REVISION STATUS: Revised to meet the ANSI standard of 16 sections THIS SAFETY DATA SHEET (SDS) HAS BEEN PREPARED IN COMPLIANCE WITH THE FEDERAL OSHA HAZARD COMMUNICATION STANDARD, 29 CFR THE INFORMATION IN THIS SDS SHOULD BE PROVIDED TO ALL WHO WILL USE, HANDLE, STORE, TRANSPORT, OR OTHERWISE BE EXPOSED TO THIS PRODUCT. THIS INFORMATION HAS BEEN PREPARED FOR THE GUIDANCE OF PLANT ENGINEERING, OPERATIONS AND MANAGEMENT AND FOR PERSONS WORKING WITH OR HANDLING THIS PRODUCT. THIS INFORMATION IS BELIEVED TO BE RELIABLE AND UP TO DATE AS OF THE DATE OF PUBLICATION BUT, MAKES NO WARRANTY THAT IT IS. I s o d o d e c a n e - R e v i si o n D a y : J a n u a r y 1, P a g e 5 5