Lockout - Tagout. Control of Hazardous Energy OSHA Standard
|
|
- Barbara Owen
- 5 years ago
- Views:
Transcription
1 Lockout/Tagout
2 Lockout - Tagout Control of Hazardous Energy OSHA Standard
3 What Is Lockout/Tagout? Referred to as LOTO Blocks the flow of energy from power source to the equipment Provides means of warning (tag)
4 Why is Lockout/Tagout Important? OSHA s Top 10 Most Cited Violations: Lockout / Tagout has ranked 4 th on the list for the last two years. Over 4,000 violations per year.
5 Types of Energy Electrical Mechanical Chemical Thermal Hydraulic Pneumatic
6 Use Safe Electrical Practices Use non-conducting tools. Check circuits dead before working. Ensure all control power is de-energized. Discharge all capacitors after lockout.
7 Mechanical Energy Hazards Kinetic energy in motion Potential - stored energy Energy stored in machinery Weights & Springs Pistons under pressure Hydraulic controls Stored potential energy can be released during work causing injury or death.
8 Chemical Energy Hazards Chemicals have energy that can: start fires cause skin burns generate harmful gases or fumes Before working release, drain or vent chemicals safely.
9 Thermal Energy Hazards Energy of Heat and Cold Hot or cold equipment & fluids can burn you Quick releases of compressed gases can freeze your skin Allow equipment to reach a safe temperature before starting work.
10 Hydraulic Energy Energy of Liquids Under Pressure pressure can cause equipment to move rapid release can cause injury or ejection of system parts Block energy or relieve pressure slowly into a proper container.
11 Pneumatic Energy Hazards Energy of Compressed Gases uncontrolled release can cause injury rapid de-pressurization creates extreme low temperature Properly vent all systems before starting work.
12 LOTO Procedure 1. Prepare for Shutdown 2. Shutdown Equipment 3. Isolate all energy sources 4. Place Locks & Tags 5. Release Stored Energy 6. Verify Equipment Isolation
13 1. Prepare for Shutdown Understand equipment hazards! Notify other employees of shutdown.
14 2. Shutdown Equipment Follow normal shutdown procedure. Turn all switches to the OFF position. Shut all valves. Disable all sources of energy!
15 3. Isolate All Energy Sources Shut valves Open breakers & disconnects
16 4. Place Locks & Tags Valves Breakers / electrical disconnects Block or disconnect all lines
17 5. Release or Block all Stored Energy Discharge capacitors Block or release springs Block elevated parts Stop rotating parts Relieve system pressure Drain fluids Vent gases Allow system to cool
18 6. Verify Equipment Isolation Check all other workers are clear of the equipment. Check locking devices securely placed. Check isolation. Attempt normal startup. Return Controls to OFF/Neutral.
19 Items needed for LOTO Written LOTO procedures Locks & Tags Hasps --for multiple locks & tags Breaker Lockouts Gate Valve Lockouts Ball Valve Lockouts
20 Types of Lockout Devices Locks Blocks Chains Multilock hasps Wheel valve covers Ball valve covers
21 Requirements for Lockout/Tagout Devices They must be: Durable Standardized Substantial Identifiable
22 Presses Saws Conveyors Pumps Production equipment Trash compactors Ovens Typical Equipment Requiring LOTO
23 Affected Employees Employees who Operate Work around Occasionally adjust equipment that is subject to LOTO
24 Affected Employee Responsibilities Notify maintenance, etc., when equipment needs repair or adjustment Leave all LOTO devices in place Verify equipment is safe to operate following LOTO Follow all safety rules while operating the equipment
25 Authorized Employee Maintains equipment Services equipment Is trained to use LOTO
26 Authorized Employee Responsibilities Repair or service equipment as needed Ensure that all energy sources are locked out Test equipment to verify residual energy is dissipated Place a Danger Do Not Operate tag on equipment Obtain assistance when necessary Remove locks and/or tags following LOTO Coordinate multi-shift repair
27 Training Requirements Authorized employees initially and at least annually Affected employees at least initially Authorized and affected whenever changes are made to jobs or procedures Authorized and affected when program deficiencies are noted
28 Company Responsibilities Ensure de-energization of equipment Ensure employee awareness Provide appropriate levels of training Review program effectiveness Maintain and revise program Administer appropriate disciplinary actions
29 When Must LOTO Be Used? When servicing or maintaining equipment where: Hazardous energy exists Unexpected start-up could occur Employees are required to remove or bypass a safety device Employees are required to place any part of their body in harm s way Employees are exposed to hazardous energy
30 LOTO Exceptions Work where hazardous energy does not exist Activities performed during routine production processes Work on cord-controlled devices Hot tap operations where shutdown is not feasible
31 Releasing Equipment from LOTO Inspect Area and Equipment. Ensure all Machine Guards in place. Move tools away from equipment. Inform others of startup. Restore system connections. Remove Locks & Tags. Restore equipment to normal. Conduct normal startup.
32 Know the Equipment! Hazards Energy isolation points Lockout/Tagout procedures Working on unfamiliar machinery is a hazard!
33 Who Can Lockout Equipment? Only employees who have been trained and authorized by management.
34 Who can remove Locks & Tags? Only the employee who placed the tag or a supervisor, after obtaining permission from the worker who placed the tag.
35 Lockout-Tagout Protects YOU! ALWAYS Use Proper Lockout - Tagout Procedures They are for your protection!!!
Control of Hazardous Energy (Lockout/Tag-out) 29 CFR
Control of Hazardous Energy (Lockout/Tag-out) 29 CFR 1910.147 What Is Lockout/Tag-out? Referred to as LOTO Blocks flow of energy from power source to the equipment Provides means of warning (tag) Regulatory
More informationThis session covers the safety procedure known as lockout/tagout, which is required by Occupational Safety and Health Administration (OSHA) in its
This session covers the safety procedure known as lockout/tagout, which is required by Occupational Safety and Health Administration (OSHA) in its standard on Control of Hazardous Energy. This is part
More informationLOCKOUT/TAGOUT: Operating Procedure TABLE OF CONTENTS
LOCKOUT/TAGOUT: Operating Procedure TABLE OF CONTENTS A. PURPOSE 1 B. FACILITIES STAFF RESPONSIBILITIES 2 C. TRAINING AND RETRAINING of AFFECTED and EUTHORIZED EMPLOYEES 3 NINE POINTS TO REMEMBER 5 LOCKOUT/TAGOUT
More informationH. Control of Hazardous Energy: Lockout/Tag Out
H. Control of Hazardous Energy: Lockout/Tag Out 1. Purpose Control of Hazardous energy is the purpose of the Lockout- Tagout Program. This program establishes the requirements for isolation of both kinetic
More informationUniversity of Arkansas Office of Environmental Health and Safety
University of Arkansas Office of Environmental Health and Safety Procedure Name: Lockout / Tagout Procedure Number: 600.26 Effective Date: 12-1-2015 Procedure: Developed in accordance with the OSHA Control
More informationLockout Tagout Program
Lockout Tagout Program RIM of the World Unified School District 27315 North Bay Road Blue Jay, CA 92352 (909) 336-4100 July 2016 Safety and Risk Management Department RIM of the World Unified School District
More informationLockout / Tag out Program
Lockout / Tag out Program Presented by DOSHTI www.doshti.com You will learn Purpose of Lockout- Tag out Requirements for LOTO Types of Hazardous Energy Procedures for LOTO The OSHA Standard for the Control
More informationControl of Hazardous Energy Lockout / Tagout Program
Control of Hazardous Energy Lockout / Tagout Program August 2016 Table of Contents Purpose... 1 Scope and Application... 1 Responsibilities... 1 Environmental Health and Safety Personnel (EH&S)... 1 Directors
More informationLockout / Tagout Safety Program
Lockout / Tagout Safety Program Prepared by: The Ohio State University Environmental Health and Safety Occupational Safety & Industrial Hygiene 1314 Kinnear Road Columbus, OH 43212-1168 614-292-1284 Phone
More informationLockout/Tagout - Energy Control Program
Lockout/Tagout - Energy Control Program Lockout and Tagging of ELECTRICAL Circuits This portion of the K.R. Miller Contractors, Inc. safety program has been created to maintain a written copy of procedures
More informationPAGE 1 OF 7 HEALTH, SAFETY & ENVIROMENTAL MANUAL PROCEDURE: S230 Lock-Out Tag-Out (LOTO) Program REV 4.0 8/13/2012
PAGE 1 OF 7 LOCK-OUT TAG-OUT (LOTO) THE CONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM PURPOSE: 1. This standard establishes lockout/tagout (LOTO) procedures for the safety of personnel working on
More informationLockout/Tagout Program
Lockout/Tagout Program Control of Hazardous Energy Subpart J - 29 CFR 1910.147 29 CFR 1926.417 OSHA Standard All industries must comply Estimated to prevent Approximately 120 fatalities per year 28,000
More informationLockout/Tagout Program
Lockout/Tagout Program Prepared by: Occupational Health and Safety Reviewed by: Joint Health and Safety Committees Approved by: Chief Human Resources Officer November 2014 TABLE OF CONTENTS 1.0 Purpose...3
More informationLockout Tagout Policy
Office of Environmental Health & Safety www.moreheadstate.edu/ehs 606-783-2584 Lockout Tagout Policy PURPOSE To establish procedures for the de-energization and isolation of energy sources or the lockout
More informationCONTROL OF HAZARDOUS ENERGY IN THE WORKPLACE
Office of Environmental Health & Safety CONTROL OF HAZARDOUS ENERGY IN THE WORKPLACE LOCK OUT/TAG OUT OSHA 29 CFR 1910.147 rev. 3 2014 Director of Environmental Health & Safety Control of Hazardous Energy
More informationLock Out/Tag Out Control of Hazardous Energy
Lock Out/Tag Out Control of Hazardous Energy University Facilities Internal Procedure: July 1, 2013 Effective date: July 1, 2013 Last Modified: April 2013 Approved by: Bob Wells 1.0 Program Objective UF
More informationLOCKOUT/TAGOUT PROGRAM
Santa Clarita Community College District LOCKOUT/TAGOUT PROGRAM Revised March 2018 TABLE OF CONTENTS PURPOSE... 3 COMPLIANCE...4 DEFINITIONS...5 SECTION I - ENERGY CONTROL PROCEDURES... 7 SECTION II -
More informationThe Control of Hazardous Energy (Lockout/Tagout) California State University Chico
The Control of Hazardous Energy (Lockout/Tagout) California State University Chico Department of Environmental Health and Safety Reviewed July 2008 TABLE OF CONTENTS Section Page 1.0 INTRODUCTION... 1-1
More informationLO/TO LOCKOUT/TAGOUT PROGRAM
LO/TO LOCKOUT/TAGOUT PROGRAM April 2017 CONTENTS Section 1: Introduction...1 Section 2: Purpose... 1 Section 3: Application... 1 Section 4: Definitions... 2 Section 5: Roles and Responsibilities... 4 Section
More informationLOCK-OUT/TAG-OUT (LO/TO) SAFETY PROGRAM
LOCK-OUT/TAG-OUT (LO/TO) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.147 BASIS: Approximately three million workers in the United States face risks from uncontrolled energy when servicing machinery
More informationFacilities Management
Facilities Management Policy Number: 700.6 Title: Lockout/Tag Out Policy Implementation Date: 2004 Last Audited: July 2 nd, 2018 Last Revised: March 25 th, 2015 Introduction This policy contains the necessary
More informationPALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT
1. De-energize circuit serving the outlet following LOTO procedure (see pages 3 5). PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT Department: Facilities Campus: All
More informationProduct Information Report Lockout/Tagout Hazardous Energy Control
Overview A properly implemented (LOTO) program is designed to protect workers involved in the maintenance and servicing of equipment from the dangerous effects of hazardous energy caused by the unexpected
More informationLockout/Tagout Training Overview. Safety Fest 2013
Lockout/Tagout Training Overview Safety Fest 2013 Purpose of Lockout/Tagout The standard covers the servicing and maintenance of machine and equipment in which the unexpected energization or start up of
More informationLockout/Tagout Program Occupation Safety & Health Standards for General Industry 29 CFR
Volunteer State Community College Lockout/Tagout Program Occupation Safety & Health Standards for General Industry 29 CFR 1910.147 The information contained in this maual documents the policies and procedures
More informationLOCKOUT/TAGOUT PLAN August 2015
LOCKOUT/TAGOUT PLAN August 2015 Office of Environmental Health and Safety 423-354-5224 TABLE OF CONTENTS Purpose and Intended Use... 2 A. Types of Energy Sources... 2 B. Activities Requiring Lockout/Tagout
More informationCONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAGOUT)
CONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAGOUT) 1. PURPOSE The purpose of this program is to establish policy, rules and procedures for the protection of employees against the unexpected energizing, start-up,
More informationCentral Washington University
Central Washington University Lockout / Tagout (LOTO) Program Plan prepared by: Central Washington University Office of Environmental Health & Safety 400 East University Way Ellensburg, WA 98926 P: 509-963-2252
More informationLockout/Tagout Program
Purpose Hazardous energy appears in the workplace in the form electrical, mechanical, pneumatic, hydraulic and thermal energy and includes chemical, water, steam and gaseous energy systems. Lockout/Tagout
More informationLockout/Tagout - Control of Hazardous Energy Program
Lockout/Tagout - Control of Hazardous Energy Program The University Of Iowa Environmental Health & Safety 122 Grand Avenue Court Iowa City, IA 52242-1000 Phone: 319-335-8501 Date Revised/Reviewed: 6/8/2018
More informationPALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT
PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT Department: Facilities Campus: All Task: Replace a Light Ballast Job Title(s) Performing Task: Electrician, Maintenance
More informationDUQUESNE UNIVERSITY LOCKOUT/TAGOUT PROGRAM
DUQUESNE UNIVERSITY LOCKOUT/TAGOUT PROGRAM Prepared by: Environmental Health and Safety Department TABLE OF CONTENTS Page Purpose 1 Scope 1 Introduction 2 Regulatory Requirements 2 Protective Materials
More information2523-LDG-E. Leader s Guide
2523-LDG-E LOCKOUT/TAGOUT TRAINING FOR EMPLOYEES Leader s Guide 2008 ERI Safety Videos LOCKOUT/TAGOUT TRAINING FOR EMPLOYEES This easy-to-use Leader s Guide is provided to assist in conducting a successful
More informationUniversity of Vermont Department of Physical Plant Burlington, Vermont
University of Vermont Department of Physical Plant Burlington, Vermont CONTROL OF HAZARDOUS ENERGY SOURCES AND ELECTRICAL HAZARDS LOCKOUT AND TAGOUT PROGRAM in accordance with OSHA 29 CFR 1910.147 REVISED
More informationLockout/Tagout Safety Policy
University of North Carolina Wilmington Environmental Health & Safety Workplace Safety Lockout/Tagout Safety Policy GENERAL The UNCW Environmental Health & Safety Department (EH&S) is authorized by UNCW
More informationCONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAG OUT PROGRAM) Washington State University Tri-Cities (all departments)
CONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAG OUT PROGRAM) Washington State University Tri-Cities (all departments) PURPOSE This program establishes the general and specific requirements for the control of
More informationEM Section 12. Control of Hazardous Energy (Lockout/Tagout)
EM 385-1-1 Section 12 Control of Hazardous Energy (Lockout/Tagout) Lockout/Tagout References EM 385-1-1 Section 12 29 CFR 1926.600 (a) (3) i Heavy Equipment 29 CFR 1926.702 (j) (1) Concrete Tools 29 CFR
More informationLockout/Tagout Manual
Manual 2408 Wanda Daley Drive Ames, Iowa 50011-3602 (515) 294-5359 www.ehs.iastate.edu Copyright Environmental Health and Safety 2809 Daley Drive Ames, IA 50011-3660 Ph: (515) 294-5359 www.ehs.iastate.edu
More informationMARIPOSA COUNTY LOCKOUT/TAGOUT PROGRAM
MARIPOSA COUNTY LOCKOUT/TAGOUT PROGRAM INTRODUCTION Mariposa County ( County ) facilities have equipment and systems that must be deenergized to allow for safe cleaning, repairing, servicing, setting-up,
More informationCONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAGOUT) PROGRAM
Page: 1 of 15 1.0 Purpose and Applicability 2.0 Scope 1.1 It is the policy of the University of Pennsylvania in coordination with the Office of Environmental Health and Radiation Safety to provide the
More informationHazardous Energy Control (Lockout-Tagout)
Hazardous Energy Control (Lockout-Tagout) The purpose of this program is to prevent inadvertent operation or energization of machines, equipment, or processes in order to protect employees and establish
More informationHealth, Safety, Security and Environment
Document owner and change code Document Owner Aaron Perronne Title HSSE Manager Mark X Change Code Description X N/A First Issue A Typographical/Grammatical correction; formatting change; text clarification-no
More informationElements of a Lockout/Tagout Program OSHA
September 15, 2015 Elements of a Lockout/Tagout Program OSHA 1910.147 Dayna Noble Industrial Safety Consultant Specialist Ohio BWC 567-204-8917 Dayna.noble@bwc.state.oh.us Top 10 most frequently cited
More informationLockout/Energy Control
Lockout/Energy Control Presented By: Sotaris, LLP 2000 Auburn Drive, Suite 200 Beachwood, Ohio 44122 P: 216-378-7650 F: 866-794-5756 W: www.sotaris.com E: awj@sotaris.com 1 About Me Andrew W. Johnson,
More information230-LOCKOUT/TAGOUT PROGRAM
230.1 PURPOSE A. To confirm implementation, operation, and recordkeeping of Central New Mexico Community College(CNM) lockout/tagout program in compliance with 29 CFR 1910.147. 230.2 SCOPE A. The requirements
More informationCONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM
CONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM 1.0 REGULATORY AUTHORITY Code of Federal Regulations, 29 CFR 1910.147; California Code of Regulations, Title 8, Sections 2320.1 and 3314; CSU, Fullerton
More informationHazardous Energy Control Lockout/Tagout
Hazardous Energy Control Lockout/Tagout Debbie Rauen INSafe Safety Consultant Outline Energy Sources Employer Responsibilities Authorized Employee Responsibilities Energy Control (LO/TO) Equipment & Devices
More informationDuPage County Environmental, Safety, Health & Property Loss Control Program Hazardous Energy Control (Lockout/Tagout)
Purpose: To provide the minimum requirements for the lockout or tagout of energy isolating devices whenever work is performed or servicing is done on County of DuPage machinery, equipment, vehicles and
More informationSAMPLE WRITTEN PROGRAM for Control of Hazardous Energy LOCKOUT TAGOUT
SAMPLE WRITTEN PROGRAM for Control of Hazardous Energy LOCKOUT TAGOUT SAMPLE WRITTEN PROGRAM The objective of this procedure is to establish a means of positive control to prevent the accidental starting
More information2008. AURORA PICTURES
2923 LOCKOUT/TAGOUT: It Would Have Saved His Life 2008. AURORA PICTURES 1 Table of Contents Introduction 3 Video Overview.3 Introduction 3 Purpose of Lockout/Tagout 3 Hazardous Energy Sources.3 Authorized
More informationPage: 7/15/2009. Energy control procedures Use of lockout/tagout equipment to ensure safe work practices.
1 of 6 1.0 PURPOSE This program applies to the installation, service, maintenance, or removal of any type of machinery, equipment, or components, in which the unexpected start up or release of stored energy
More informationLockout Tagout Program
Lockout Tagout Program Table of Contents INTRODUCTION... 2 FORWARD... 2 OBJECTIVE... 2 APPLICABILITY... 2 RESPONSIBILITIES... 3 PROGRAM ENFORCEMENT... 4 RECORDKEEPING... 4 LOCKOUT TAGOUT EQUIPMENT... 5
More informationPRESCOTT SCHOOL DISTRICT NO South A Street Prescott, WA The Control of Hazardous Energy (Lockout/Tagout)
PRESCOTT SCHOOL DISTRICT NO. 402-37 207 South A Street Prescott, WA 99348 509-849-2217 The Control of Hazardous Energy (Lockout/Tagout) I. Purpose The Control of Hazardous Energy (Lockout/Tagout) This
More informationLockout/Tagout Plan Environmental Health & Safety Office July 2017
July 2017 Table of Contents Acronyms... iii Foreword... iv Document History... iv 1.0 Introduction... 1 1.1 Purpose... 1 1.2 Scope... 1 1.3 Lockout/Tagout Program... 1 2.0 Roles and Responsibilities...
More informationRiskTopics. Lockout/Tagout October 2017
RiskTopics Lockout/Tagout October 2017 This Risktopic is designed to outline guidelines for lockout/tagout and provide assistance in developing a management program to reduce the risk of injury from unintended
More informationWESTERN CONNECTICUT STATE UNIVERSITY LOCKOUT/TAGOUT PROCEDURE S-107
WESTERN CONNECTICUT STATE UNIVERSITY LOCKOUT/TAGOUT PROCEDURE S-107 Draft Issued 12/97 Revised 11/00 Please direct any questions or comments about the applicability of this document to Luigi Marcone, WCSU
More informationControl of Hazardous Energy. Environmental Health and Safety
Control of Hazardous Energy Environmental Health and Safety 11/01/2014 1 CONTROL OF HAZARDOUS ENERGY (LOCKOUT-TAGOUT) OSHA CFR 1910.147 Revised Date: November 2014 STATEMENT OF POLICY Ball State University
More informationDRAFT LOCKOUT/TAG OUT PROGRAM (CONTROL OF HAZARDOUS ENERGY)
DRAFT [name of unit] LOCKOUT/TAG OUT PROGRAM (CONTROL OF HAZARDOUS ENERGY) PURPOSE This program establishes the general and specific requirements for the control of hazardous energy during the servicing
More informationTHE UNIVERSITY OF NORTH CAROLINA
THE UNIVERSITY OF NORTH CAROLINA AT CHAPEL HILL CHILLED WATER DEPARTMENT ENERGY CONTROL PROCEDURE The purpose of this document is to establish minimum requirements for the manual isolation and securing
More informationLOCKOUT/TAGOUT PROGRAM
LOCKOUT/TAGOUT PROGRAM HOW CLIMATE ENGINEERS INC. COMPLIES WITH THELO/TO STANDARD It is the intent of Climate Engineers Inc. to comply with OSHA s Control of Hazardous Energy Standard (1910.147). The following
More informationTexas Department of Insurance Division of Workers Compensation. Lockout Tagout HS96-100D (8-06)
OF OF STATE THE TEXAS TEXAS Texas Department of Insurance Division of Workers Compensation Lockout Tagout HS96-100D (8-06) Contents Purpose 1 Definitions 1-2 Responsibility 2-3 Training 3 Periodic Inspections
More informationHealth and Fire Safety Review 2/15
Health and Fire Safety Review 2/15 1 TABLE OF CONTENTS Page 3 Scope 3 Control of Hazardous Energy (Introduction) 3 Authorized Employee 3 Employer Responsibility 4 Tagout Devices 4 Lockout Devices 5 General
More informationLOCKOUT/TAGOUT PROGRAM
0 Appendix C OCCUPATIONAL SAFETY AND HEALTH PROGRAM LOCKOUT/TAGOUT PROGRAM Hazardous Energy Control Lockout/Tagout Program TABLE OF CONTENTS Section Page I. Purpose and Scope. 1 II. Definitions 1 III.
More informationLockout. HealthandSafetyOntario.ca. What is Lockout? How is a Lockout Done? Why is a Lockout Necessary?
What is Lockout? Lockout means to physically neutralize all energies in a piece of equipment before beginning any maintenance or repair work. Lockouts generally involve: Stopping all energy flows (for
More informationHazardous Energy Control/Lockout
This is a photographic template your photograph should fit precisely within this rectangle. Hazardous Energy Control/Lockout MESH 8.0 - Process Safety Awareness Training 2008 Eaton Corporation. All rights
More informationLockout / Tagout Program OSHA 29 CFR
Lockout / Tagout Program OSHA 29 CFR 1910.147 Baylor University utilizes outside contractors to perform set-up, maintenance, service, and repair to equipment utilized on campus. University staff perform
More informationLOCKOUT-TAGOUT PROGRAM
LOCKOUT-TAGOUT PROGRAM Please Note: This material, or any other material used to inform employers/employees of compliance requirements of OSHA standards through simplification of the regulations should
More informationLOCKOUT / TAGOUT PROGRAM
LOCKOUT / TAGOUT PROGRAM Developed in accordance with the OSHA Control of Hazardous Energy Standard, 29 CFR 1910.147 DECEMBER 7, 2017 SKIDMORE COLLEGE 815 NORTH BROADWAY, SARATOGA SPRINGS, NY 12866 Table
More informationLOCKOUT/TAGOUT POLICY
NAVAJO COUNTY Safety Procedures Reference: PERSONNEL POLICIES & PROCEDURE SECTION: 5.4 Approved: Brett Starns Subject: LOCKOUT/ RM-Safety 09/04/2014 TAGOUT POLICY Revised: 9/16/2014 Initiating Department:
More informationMCW s Control of Hazardous Energy Program
2018 MCW s Control of Hazardous Energy Program - Lockout Tagout Program This document is MCW s written program for managing the lockout and tagout of hazardous energy, and identifies roles and responsibilities
More informationControl of Hazardous Energy Program (Lockout/Tagout)
Control of Hazardous Energy Program (Lockout/Tagout) 1 The Control of Hazardous Energy (Lockout/Tagout) Program 1910.147 The following lockout/tagout program is provided to assist employees in complying
More informationLockout Tagout Program
Lockout Tagout Program 1.0 INTRODUCTION Public Safety Department Environmental, Health and Safety (EHS) Division Standard Operating Procedure (SOP) #18 Purpose To ensure that machinery or equipment is
More informationHazardous Energies Control and Lockout/Tagout Program
Hazardous Energies Control and Lockout/Tagout Program Summary: This program applies to the installation, service, maintenance, or removal of any type of machinery, equipment, or components, in which the
More informationOKLAHOMA CITY COMMUNITY COLLEGE CONTROL OF HAZARDOUS ENERGY PROGRAM. Environmental Health and Safety. Established:
OKLAHOMA CITY COMMUNITY COLLEGE CONTROL OF HAZARDOUS ENERGY PROGRAM Environmental Health and Safety Established: Developed in accordance with OSHA Standard 29 CFR 1910.147 1 1.0 SCOPE. Oklahoma City Community
More informationLockout/Tagout. Page. Introduction. Purpose. 2 Background. 2 Who s Covered?... 3 Responsibilities. 3 Explanation of Key Terms. 4.
Lockout/Tagout Page Introduction Purpose. 2 Background. 2 Who s Covered?... 3 Responsibilities. 3 Explanation of Key Terms. 4 How It Works General Lockout/Tagout Procedure. 5 General Lock/Tag Removal Procedure.
More informationThe Proper Procedure
The Proper Procedure Lockout Lockout is used to prevent the release of hazardous energy or equipment from starting by applying a lockout device and lock A padlock is placed on the appropriate energy isolating
More informationSAFETY DIRECTIVE 2.0 DEPARTMENTS AFFECTED. This Administrative Directive shall apply to all Town of Marana departments and employees.
SAFETY DIRECTIVE Title: Control of Hazardous Energy Lock-out/Tag-out/Try-out Issuing Department: Town Manager s Safety Office Effective Date: July 1, 2014 Approved: Gilbert Davidson, Town Manager Type
More informationUCHC Lockout/Tagout Policy (4/09)
UCHC Lockout/Tagout Policy (4/09) Background: This safety policy is applicable to all Health Center activities and addresses practices and procedures that are necessary to disable machinery or equipment
More informationUniversity of Tennessee Safety Program
University of Tennessee Safety Program Policy Subject: Lockout/Tagout Program Effective Date: 4/22/98 Area Affected: All areas on campus where equipment can be locked out for service. Contact Information:
More informationEnergy Control. Suite 2A, 55 Frid Street Hamilton, ON L8P 4M3 office: cell:
Energy Control Suite 2A, 55 Frid Street Hamilton, ON L8P 4M3 office: 905.577.0303 cell: 905.977.0210 consultant@staffaid.ca www.staffaid.com Safety, Energy Control, Power Lockout & Function Test Procedures
More informationManagement Plan for Lockout Tagout (LOTO) ISD #535
Management Plan for Lockout Tagout (LOTO) ISD #535 Health & Safety Office Maintenance Service Building 10 SE 9½ Street Rochester, MN 55904 507-328-4507 Modification Date Document Modification Form All
More informationSample Written Program for The Control of Hazardous Energy (Lockout/Tagout)
USAG Bavaria Safety Office Sample Written Program for The Control of Hazardous Energy (Lockout/Tagout) Nov 2016 1910.147 The Control of Hazardous Energy (Lockout/Tagout) The following lockout/tagout program
More informationLock-out Tag-out Program (Zero Energy State)
Lock-out Tag-out Program (Zero Energy State) Department: Environmental Health and Safety 2 TABLE OF CONTENTS Section Title Page 1.0 Scope and Responsibilities. 3 2.0 Examples of Potential Energy and Zero
More informationARKANSAS TECH UNIVERSITY FACILITIES MANAGEMENT HEALTH AND SAFETY MANUAL (LOCKOUT/TAGOUT) 30.0
() 30.0 The purpose of the Energy Control Policy (Lockout/Tagout) is to ensure that before any employee performs any servicing and/or maintenance on machinery or equipment, where the unexpected energizing,
More informationLOCKOUT/TAGOUT PROGRAM
LOCKOUT/TAGOUT PROGRAM PURPOSE The purpose of this program is to prevent the unexpected energization or start-up of machines and equipment, or the release of stored energy, in order to prevent workplace
More informationUNIVERSITY OF ROCHESTER ENVIRONMENTAL HEALTH & SAFETY
Revision No.: 3 Page 1 of 20 I. PURPOSE The purpose of this program is to prevent injuries and accidents from occurring while servicing or maintaining machinery or equipment that is capable of sudden energy
More informationHazardous Energy Program Lockout/Tagout
Hazardous Energy Program Lockout/Tagout Last Revision Date: 11/7/2016 I. PURPOSE... 2 II. SCOPE... 2 III. REFERENCES... 2 IV. RESPONSIBILITIES... 2 A. Supervisors... 2 B. Employees:... 3 1. Authorized
More informationHealth & Safety Policy and Procedures Manual SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY
SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY 1. CONTROL OF HAZARDOUS ENERGY POLICY AND PROCEDURES A. OSHA References: 29 CFR 1910.147, 29 CFR 1910.332, 29 CFR 1910.333, 29 CFR 1926.417 B.
More informationCITY OF NEW LONDON LOCKOUT/TAGOUT PROGRAM
CITY OF NEW LONDON LOCKOUT/TAGOUT PROGRAM (HAZARDOUS ENERGY CONTROL) May 1, 2003 1 LOCKOUT/TAGOUT PROGRAM (HAZARDOUS ENERGY CONTROL) I. PURPOSE The purpose of this Hazardous Energy Control Program is to
More informationGettysburg College. Energy Control Program
Gettysburg College Energy Control Program Adopted October 2009 Reviewed and Updated February 2015 Reviewed and Updated July 2015 I. Energy Control Procedures Table of Contents A. General Lockout Procedures
More informationPART Q CONTROL OF HAZARDOUS ENERGY (LOCKOUT-TAGOUT)
PART Q CONTROL OF HAZARDOUS ENERGY (LOCKOUT-TAGOUT) WAC Page 296-307-320 Control of hazardous energy (lockout-tagout). 1 296-307-32001 What does this section cover? 1 296-307-32003 When does this section
More informationSAINT MARY S COLLEGE OF CALIFORNIA STANDARD HAZARDOUS ENERGY CONTROL PROGRAM INCLUDING LOCKOUT/TAGOUT. Prepared by
SAINT MARY S COLLEGE OF CALIFORNIA STANDARD 1.1.4 HAZARDOUS ENERGY CONTROL PROGRAM INCLUDING LOCKOUT/TAGOUT Prepared by SAINT MARY S COLLEGE OF CA MORAGA, California KAREN LAURICELLA Original Date: 1 JULY
More informationHazardous Energy Control
Lockout Tagout This program has been prepared to provide assistance in compliance with USA OSHA standards and/or Best Management Practices. It should not be used without consideration of the unique conditions
More informationE2.14 Control of Hazardous Energy. Effective Date: 03/01/2018
University Policy Volume E2: Environment, Health, Safety and Security E2.14 Control of Hazardous Energy Responsible Office: Facilities Management Responsible Officer: Safety Officer POLICY STATEMENT All
More informationEnvironmental Health & Safety Programs
1.0 Program Description The Radford University Hazardous Energies Control and, as maintained by Environmental Health and Safety (EHS), applies to all employees who service or maintain machinery, equipment,
More informationTHE OSHA LOCK-OUT/TAG-OUT STANDARD
PRESENTER'S GUIDE "LOCK-OUT/TAG-OUT" Training for THE OSHA LOCK-OUT/TAG-OUT STANDARD Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS OUTLINE OF MAJOR PROGRAM
More informationEnvironmental Health & Safety
Environmental Health & Safety Oklahoma State University LOCKOUT / TAGOUT PROGRAM MANUAL Environmental Health and Safety University Health Services Suite 002 Stillwater, OK 74078 (405) 744-7241 www.ehs.okstate.edu
More informationANNUAL IDOL COMPLIANCE TRAINING
ANNUAL IDOL COMPLIANCE TRAINING Lock Out / Tag Out Refresher SUGAR GROVE FIRE DEPARTMENT 1 TRAINING DIVISION Instructions To complete this independent study program, view the entire program, advancing
More informationGeneral Lockout Training Briefing
Page 1 of 5 Introduction What is Lockout? Lockout protects your personnel and plant from injury or accident by ensuring that equipment and machinery is properly isolated during scheduled maintenance, shutdown,
More informationControl of Hazardous Energy Program (LOTO)
1.0 PURPOSE The purpose of this program is to establish minimum safety requirements for the lockout and tagout of hazardous energy sources and the verification of energy isolation through the use of isolating
More information