Working in Gas Hazard Areas
|
|
- Randolf Douglas
- 5 years ago
- Views:
Transcription
1 / Health & Safety OPERATIONS STANDARDS Ref.: Aperam Safety ST 012 Working in Gas Hazard Areas Issue: Vers.: v0 Rev.: AM Safety ST 012 v Working in Gas Hazard Areas Controlled Updated by: Validated by: Approved by: Circulation Name : Edméa Azevedo Leonam Almeida Ilder Camargo 1. Scope 1.1. This standard describes minimum requirements for working in a potentially hazardous gaseous environment (Gas Hazard Areas), to prevent the formation of explosive mixtures or zones of explosive atmospheres, a build up of asphyxiate or toxic gas (incl. gases taking the place of O 2 ), or to manage the oxygen levels to prevent either extremely rapid combustion or suffocation (harmful atmospheres). It covers permanent Gas Hazard Areas are areas such as blast furnaces and coke plants, areas with combustion gases or gases coming from DRI plant, by-products treatments, combustible and / or solvents tanks, gasoline powered engines in partially enclosed areas but does not include confined space entry requirements which are covered separately in Aperam Confined Space Standard (Aperam Safety ST 002) with specific procedures. So both standards must be considered together It is mandatory to comply with local regulations. In addition, this standard must be applied when it is more demanding than local regulations This standard does not apply to the underground part of the mine site. For that part of the mine specific regulations apply, according to the standards and law in the relevant countries. However this standard does apply for the gas hazardous areas at the surface part of the mine. 2. Gas Hazard Areas 2.1. Each site must have a documented and up to date risk assessment for each area and task associated with working in potentially hazardous gaseous environments Each site must have an up to date layout plan in which all Gas Hazard Areas are highlighted and in the operative pulpit a system of alarms particularly for levels CO Safe work and purge procedures shall refer to the risk assessment and specify appropriate controls for all work. These should include at least items such as the required hot work, PPE, purging and permitting, monitoring, isolation, consideration for using a safety stand-by person; the emergency response should be included in the risk reduction strategy. This is to be completed with any relevant specific local condition. Health & Safety 1
2 2.4. All such areas highlighted by the risk assessment shall have appropriate warning signs posted and a permit system for controlled access to authorized employees and contractors must exist Working in the area of chimneys, where combustion gases are leaving, is considered as a gas hazard area. 3. Competencies 3.1. Each person (including contractors) working in Gas Hazard Areas must be appropriately trained in the specific tasks as well as the emergency procedures Training contents and list of people trained must be documented. Trained people must be able to identify themselves (certificate). This certificate is limited in time and renewable periodically. 4. Procedures and Permitting 4.1. A risk assessment must be used to develop the most appropriate safe work procedure and shall include an assessment of areas (inside as well as outside the plant) that may be affected by any release of gas There must be a process where a written permit (one time task) or a written procedure (repetitive or continuous jobs) is used to plan and control the work involved in isolating, purging and making the area safe for maintenance and other activities. All isolations made to render the work safe must be physical isolations and follow the Aperam Isolation Standard (Aperam Safety ST 001) Appropriate gas monitoring must be done before, during and after work has been completed. In some cases, defined by a risk assessment, monitoring may not only include displaying, but also include e.g. audible, vibration and warning lights alarms. Use of more than 1 monitor at the same time to measure before entering provides extra security and is thus to be practiced. Monitoring before the job may require use of individual respiratory equipment; this has to be included in the task description based on the risk analysis. This monitoring must be done by trained and certified people There must be a method to ensure supply of air (see also 5). 4.5 Prohibition of smoking or open flames in gas hazard areas Hot work (welding, soldering, braising, cutting, ) carries the risk of fire; as such, in a gas hazard area, these tasks may only be carried out after a duly authorized permit for hot work' has been issued. 5. Air supply 5.1. Any supply of air is to be according the quality specified in prevailing local regulations. Health & Safety 2
3 5.2. As a minimum Compressed breathing air shall meet at least the following requirements: - Oxygen content of %; - Hydrocarbon (condensed) content of less than 5 milligrams per cubic meter of air; - Carbon monoxide (CO) content of less than 10 ppm; - Carbon dioxide content of less than 1000 ppm; and - Lack of noticeable odor Breathing apparatus must not be supported by the use of portable compressors for air intake There must be a method, incl. documentation and testing information per apparatus, for assuring the functionality and condition of all components of breathing apparatus such as mask seals, mask visibility, valves for control of breathing, cylinder regulation, pressure measurement and hoses. 6. Comments 6.1 A systematic plan for revision of leakages in gas hazardous areas must be drawn up and put in practice All pipes will be painted using normalized colours, especially in maintenance zones Gases regulations will strictly be applied during design of any construction, taking into account open spaces or enough ventilation Avoid O 2 close to any combustible in restricted zones, particularly for grease, oil, and other lubricant products Gasoline-powered tools should best be used outdoors to avoid combustion gases inside the workplace. If in a building, proper evacuation of the combustion gases to the outside of the building is needed, as well as ventilation. Continuous measurement of the presence of dangerous gases, with alarm at the entry of the building, is considered best practice 6.6. Never use O 2 instead of compressed air for cleaning purposes. 7. Detectors 7.1. Generally, use multi-gas detectors Exception : when the highlighted Gas Hazard Areas layout plan, based on a risk analysis, permits adapted specified detectors 7.2 When the risk assessment requires some portable gas detectors must be used to enter into a gas hazard area, each worker (own people as well as contractors) must be individually equipped with an appropriate individual detector. Each user must be trained to the proper use of the considered detector and will assume the responsibility and discipline to maintain it in a good state of use. The use of a single portable detector for several workers is not recommended even when they work together because depending of the gas density, it s concentration in the atmosphere can change from the location where the detector is to another one only 1meter away. Health & Safety 3
4 7.3. There must be a system in place to inspect all equipment and to test and calibrate all gas monitoring devices (fixed and personal) 7.4. CO-detectors Thresholds to be used must not be higher than : 30ppm for low level, enabling 8h time of presence 100ppm for high level, enabling 1h time of presence See CO hazard curve in attachment O2 Two levels of detection to be used; recommended values are : Low 19,5 % High 22,5 % Do not forget : the detector reaction time is NOT immediate; it takes 10 to 20 sec to establish the proper measurement. This must be taken into account in the local procedures. To be clear : the detectors used must be able to detect both limits since having lower or higher values may both lead to fatalities Explosion Risk Explosion risk is detected through hydrocarbons (mainly CH4) and expressed in % of Low Explosion Limit (LEL); The 2 levels are recommended not to be set higher than 10% resp. 20% of LEL H2S This measurement is required if H2S is contained in gases (for ex COG) but also created by decomposition of organic matters (for ex in water pits) Recommended detection levels : Low 5 ppm High 10 ppm 7.8. Calibration There must be a system in place to inspect all equipment and to test and calibrate all gas monitoring devices (fixed and personal). Calibration has to be done strictly according to the prescriptions of the supplier (frequency and method). Health & Safety 4
5 Calibration has to be documented per detector. So all detectors have to be numbered Calibration is to be done by certified personnel (supplier or properly trained own people) Procedures Local procedures must describe actions to be taken for each alarm level for each type of gas alarmed by the detectors. 8. Emergency Response 8.1. Unexpected release of gas must be included in the site s overall emergency response plan and must consider all potentially affected areas on and off the site. The emergency response plan must include the type, inspection and location of appropriate emergency rescue equipment Emergency response plans must be regularly practiced and evaluated according to the risk assessment. Health & Safety 5
6 Attachment POISONING WITH CARBON MONOXIDE (CO) Health & Safety 6
Working in Confined & Enclosed Space Policy
Working in Confined & Enclosed Space Policy Author: Alan Bryant Page 1 of 9 Table of Contents: 1. INTRODUCTION... 3 2. DOCUMENT HISTORY... 3 3. REFERENCES... 3 4. PURPOSE... 4 5. SCOPE... 4 6. IMPLEMENTATION...
More informationRespiratory Protection
Respiratory Protection Purpose The purpose is to establish a set of guidelines for the selection of respiratory protection equipment, situations for its use, and training in the use of the respirator required.
More informationRockhampton Office Brisbane Office Tarong Site. Barron Gorge Hydro PS Kareeya Hydro PS Mica Creek PS
Business Procedure Hot Work Document Number OHS-PROC-128 This document applies to the following sites: All Sites Rockhampton Office Brisbane Office Tarong Site Barron Gorge Hydro PS Kareeya Hydro PS Mica
More informationUTAS EH&S INSTRUCTION No. 036 June 2012 Revision No. 3. Purging of Flammable Gas Equipment and/or Piping (Explosion Hazard)
Purging of Flammable Gas Equipment and/or Piping (Explosion Hazard) APPLICABILITY: This EH&S Instruction applies to UTAS sites worldwide, including contractors working at UTAS facilities. The document
More informationConfined Spaces. This procedure applies to all workers of the Diocese of Maitland Newcastle (DoMN).
Purpose To provide guidance in controlling the risks associated with confined spaces including identifying confined spaces, working in a confined space and issuing confined space entry permits. Scope This
More informationManagement Plan for Confined Spaces
IEA, INC. W A S ECA P U B L I C S C H O O L S I S D # 829 Contact Us: BROOKLYN PARK OFFICE 9201 W. BROADWAY, #600 BROOKLYN PARK, MN 55445 763-315-7900 MANKATO OFFICE 610 N. RIVERFRONT DRIVE MANKATO, MN
More informationPROPERTY & ESTATES GROUP
PROPERTY & ESTATES GROUP SAFE WORKING PROCEDURE 2-17-04 WORKING IN CONFINED SPACES Purpose of Document This document describes SRUC s policy and procedure for working in confined spaces. It applies to
More informationSAFETY POLICY AND PROCEDURE MANUAL All Euramax Subsidiaries. Number K-3.0 Welding Safety Procedures
Number K-3.0 Issued: 1/2009 Revised: 3/2016 Page 1 of 3 1.0 PURPOSE: To standardize procedures associated with production and maintenance welding and to minimize the potential risk of accident or injury
More informationCONFINED SPACE ENTRY & RESCUE
Training Brochure CONFINED SPACE ENTRY & RESCUE Introduction This training program is a 2-days training, which comes with an adequate training in confined space rescue operations, with intensive practical
More informationHampstead Hill School Health and Safety Policy: Confined Spaces
All Hampstead Hill School Policies are always to be read and considered in conjunction with Equal Opportunities, Race Equality and Inclusion Policies. This Policy of Hampstead Hill School applies to all
More informationStandbys. (Owner: Risk Management Section Supervisor)
BTCP/BTRF Standbys (Owner: Risk Management Section Supervisor) Site Safety Standard 5500 Introduction Scope The purpose of this standard is to specify detailed roles and responsibilities of Standby personnel
More informationRainy River District School Board SECTION 7
Rainy River District School Board SECTION 7 Health & Safety CONFINED SPACE ENTRY PROCEDURE PURPOSE 7.02 The Rainy River District School Board will identify all confined spaces and ensure that these spaces
More informationCITY AND COUNTY OF DENVER CR&CF RISK UNIT Compressed Gas Safety Standard
CITY AND COUNTY OF DENVER CR&CF RISK UNIT 65.5.11 Compressed Gas Safety Standard 1.0 Introduction 2.0 Scope This standard has been developed to protect all City and County of Denver employees and contractors
More informationSAFETY FACT SHEETS. Confined Space Entry Safety Non Negotiable. G-HS-ST Confined Space Entry. G-HS-FS Verison 1
SAFETY FACT SHEETS Confined Space Entry Safety Non Negotiable G-HS-ST-00736 Confined Space Entry Safety Non-Negotiables (SNN) Zinfra Group is committed to providing a safe workplace in line with our number
More informationSOP. Working in Confined Spaces
Purpose This procedure outlines the requirements for the management of entry into confined spaces in all work areas with the intention of minimising risks to health and safety from any potential hazards
More informationUNIVERSITY OF BATH HEALTH & SAFETY STANDARD Confined Spaces
UNIVERSITY OF BATH HEALTH & SAFETY STANDARD Confined Spaces Version Number Version 1 Date of Approval 20 th December 2016 Review Date Three years from acceptance by the UHSC Author & Lead Aims Scope Relevant
More informationCONFINED SPACE PROGRAM
CONFINED SPACE PROGRAM Last updated: November 2017 1.0 PURPOSE Entry into a confined space represents a significant risk of serious injury or death to individuals not prepared for the hazards they may
More informationConfined Space Entry. My Experience so far.
Confined Space Entry My Experience so far My Experience so far Complacency to Confined Space working Is the area a Confined Space No company procedures Poor risk assessments A lot of confusion Staff &
More informationConfined Spaces. 1. Definition Permit/Non-Permit
1. Definition Permit/Non-Permit Confined Spaces A. Non-Permit Required Confined Space: 1. Large enough and so configured that an employee can bodily enter and perform assigned duties. 2. Has a limited
More informationPUBLIC COMPANY ORLEN LIETUVA OCCUPATIONAL HEALTH AND SAFETY PROCEDURE BDS-12 USE OF PORTABLE GAS ANALYZERS I. GENERAL
PUBLIC COMPANY ORLEN LIETUVA APPROVED BY Deputy Director of Quality, Labor Safety and Environmental Control Director 30 November 2017 Order No TV1(1.2-1)-457 OCCUPATIONAL HEALTH AND SAFETY PROCEDURE BDS-12
More informationConfined Space Program
Type: POLICY Revision: 01 Owner: BRL Document Name: HSPOL 011 Status: Current Nov 2014 Review Date: September 2017 Effective Date: 01 January 2015 Total Pages: 6 Definitions: New Old Confined space means
More informationA. Evaluation of the written program
A. Evaluation of the written program Begin your audit with an evaluation of the written respiratory protection program. In addition to the operating procedures describing respirator selection and use in
More informationSafe work in confined spaces
Safe work in confined spaces This leaflet is aimed at employers and the self-employed who carry out work in confined spaces, and forms part of HSE s commitment to make simple and practical guidance available
More informationCal/OSHA T8 CCR 1536 Cal/OSHA T8 CCR 4799 Cal/OSHA T8 CCR 4845 Cal/OSHA T8 CCR 4848
Cal/OSHA Gas Systems for Welding GAS WELDING Cal/OSHA T8 CCR 1536 Cal/OSHA T8 CCR 4799 Cal/OSHA T8 CCR 4845 Cal/OSHA T8 CCR 4848 When performing gas welding, the following precautions, work procedures,
More informationProtocol for Confined Space Entry Requirements
Occupational Health and Safety (OHS) Policy Document Number # QH-PTL-275-12-1:2012 Protocol for Confined Space Entry Custodian/Review O fficer: Director Safety and Wellbeing Version no: 1.0 Applicable
More informationCONFINED SPACE PROGRAM
CONFINED SPACE PROGRAM I. Purpose This Confined Space Program has been developed in accordance with the Occupational Safety and Health Administration (OSHA) regulations 29 CFR 1910.146. The purpose of
More informationIntroduction to Confined Space Safety OR-OSHA
Introduction to Confined Space Safety OR-OSHA 215 0501 Trainer Name Position Company Phone Email (Revise as needed) Objectives This class provides the following information: 1. Criteria for confined spaces
More informationScope: This plan applies to all personnel, including contractors, who enter or work in confined spaces, or supervise such activities.
11/13/1995 4 5/20/2013 1 of 10 Authority and Scope Regulation: 29 CFR 1910.146 Scope: This plan applies to all personnel, including contractors, who enter or work in confined spaces, or supervise such
More informationToolbox Talk. Carbon Monoxide
Carbon Monoxide Toolbox Talk Carbon monoxide defies all five human senses. You can t see it, smell it, touch it or taste it and you certainly can t hear this potentially deadly gas, which has been called
More informationConfined Space Entry
Confined Space Entry Construction Industry Standard 1926.21(b)(6) General Industry Standard 1910.146 Best Practices for all Industries Construction Industry Standard All employees required to enter into
More informationSAFETY IN CONFINED SPACES AND HEALTH SAFETY EXPLOSION HAZARD - TOXIC HAZARD
a five page issue revision of 1-1995 When paints containing solvents are applied in enclosed or confined spaces, two hazards can exist, explosion and toxicity and precautions must be taken to eliminate
More informationSafety Tips from the WorkSafe People. Building a Safety Program for Your Organization
Building a Safety Program for Your Organization 1 Content Criteria and Examples of Confined Spaces Permit-Required Confined Space Non-Permit-Required Confined Space Employer Requirements Employee Requirements
More informationWHS PROCEDURE P Confined Spaces. Approved by: Ruth Hampton Review Date: 6 th December 2015
5 WHS PROCEDURE P21-01 Page 1 of 7 Issue: 2 1. Intent The Salvation Army Australia Eastern Territory (TSA-AUE) is committed to the provision of a safe, healthy and injury free environment for all persons
More informationSAFETY AND HEALTH STANDARD CONFINED SPACE ENTRY REQUIREMENTS Effective Date: 06/10/10 Standard: 16.2 Document Number: KUCSH0038 Rev: 07
16.2.1 INTRODUCTION 16.2.1.1 The purpose of this standard is to establish safety requirements, which include a permit system, for entry into confined spaces. 16.2.2 DEFINITIONS 16.6.2.1 Confined space
More informationThought of everything? Expert tips for working safely in confined spaces
Thought of everything? Expert tips for working safely in confined spaces Little space, lack of oxygen, and hazardous substances: Workers in the water treatment industry who enter the confined spaces of
More informationRisk Assessment & Safe Working Practice
RA Ref Number: 32 Revision: 4 Project/Job Number Reference Insert Job Number Approval Date: 30/03/2018 RA Description: confined space Next Review Date: 01/04/2019 Notes: Please refer to Safe Working Practices
More informationConfined Space Entry Program 8 CCR 5157
TABLE OF CONTENTS 1. POLICY... 2 2. PURPOSE... 2 3. SCOPE... 2 4. DEFINITIONS... 2 5. CONFINED SPACES IN THE SACRAMENTO STATE... 4 6. PERMIT SPACE ENTRY - PERSONNEL RESPONSIBILITIES... 4 6.1. CONFINED
More informationDepartment Of Facilities Management. Occupational Health and Safety. Confined Space Entry Program
Department Of Facilities Management Occupational Health and Safety Confined Space Entry Program April 2015 1 1.0 INTRODUCTION The Department of Facilities Management has identified numerous confined spaces
More informationInstructions. To complete this independent study program, view the entire program, advancing through each slide by pressing the enter key.
Instructions To complete this independent study program, view the entire program, advancing through each slide by pressing the enter key. While viewing the slides, complete the accompanying Independent
More informationKey Technology, Inc. Confined Space Entry Program. July, 2017
Key Technology, Inc. Confined Space Entry Program July, 2017 Page 1 of 11 Key Technology, Inc. CONFINED SPACE ENTRY PROGRAM OVERVIEW Purpose: The purpose of this program is to ensure the protection of
More informationState University of New York College at Oneonta
State University of New York College at Oneonta CONFINED SPACE ENTRY POLICY - PROCEDURE REVIEWED 05/11/17 CONFINED SPACE ENTRY - WRITTEN PLAN POLICY The State University College at Oneonta is committed
More informationCompressed Gases Safety Program
Compressed Gases Safety Program Summary: Compressed gas cylinders can present a variety of hazards due to their pressure and /or contents. This program covers requirements which must be followed for the
More informationSAFETY DATA SHEET GAS MIXTURES ARGON 75% CARBON DIOXIDE 25%
PAGE NO. 1 of 10 1 PRODUCT AND COMPANY IDENTIFICATION 1.1 PRODUCT IDENTIFIER : 1.1.1 PRODUCT NAME 75% Argon, 25% Carbon Dioxide 1.1.2 SYNONYMS 1.1.3 CAS NUMBER 1.1.4 CHEMICAL FORMULA Argon: 7440371 Carbon
More informationCHAPTER 16 %UHDWKLQJ*DV0L[LQJ3URFHGXUHV
CHAPTER 16 %UHDWKLQJ*DV0L[LQJ3URFHGXUHV 16-1 INTRODUCTION 16-1.1 Purpose. The purpose of this chapter is to familiarize divers with the techniques used to mix divers breathing gas. 16-1.2 Scope. This chapter
More informationINTER PLANT STANDARD STEEL INDUSTRY
INTER PLANT STANDARD STEEL INDUSTRY IPSS SAFETY PROCEDURE FOR OXYGEN, IPSS: 1-11-002-12 NITROGEN, ACETYLENE AND FUEL GASES (FIRST REVISION) Corresponding IS does not exist Formerly : IPSS: 1-11-002-98
More informationSUBSTATION MAINTENANCE ELECTRICAL OPERATING PROCEDURE
Page 1 of 6 A. PURPOSE AND SCOPE This procedure establishes safe working practices for handling sulfur hexafluoride (SF 6 ) gas and release minimization practices. This document also specifies methods
More informationTABLE OF CONTENTS PART 2 - CONFINED SPACES
May 11, 2006 TABLE OF CONTENTS PART 2 - CONFINED SPACES Page DEFINITIONS... 2-1 GENERAL... 2-2 RESPONSIBILITIES... 2-2 HAZARD ASSESSMENT AND WORK PROCEDURES... 2-3 IDENTIFICATION AND ENTRY PERMITS... 2-3
More informationASPEC Engineering HSE Management System. Work Instruction. 1 Objective. 2 Working in confined spaces. 2.1 What is a confined space?
1 Objective This work instruction has been developed to abide by the WHS Regulations (2011) and AS/NZ 2865 Safe working in a confined space. It has been developed around Hadden s typology for risk management,
More informationCONTENTS. 9. Opening of gas systems containing H 2 S. 1. Introduction. 8. Protection of Personnel.
CONTENTS 1. Introduction. 2. Properties and toxicity of H 2 S. 3. Physical effects of H 2 S. 4. Pyrophoric iron sulphide. 5. Identification of H 2 S hazard. 6. Entry to H 2 S risk area. 7. Detection of
More informationSWMS No 009 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 4
Samark North Qld Pty Ltd SWMS Manual SWMS No 009 Samark North Qld Pty Ltd ABN : 99 082 98 87 Electrical Contractors License C72 Page 2 of Safe Work Method Statement Title: SWMS:009 Confined Space Work
More informationPERMIT-REQUIRED CONFINED SPACES PROGRAM
PERMIT-REQUIRED CONFINED SPACES PROGRAM On January 14, 1993, OSHA established safety requirements to protect employees from the hazards of entry into permit-required confined spaces. It is essential to
More informationSafe Work Practices / Procedures / Instruction CONFINED SPACE
CONFINED SPACE Entry into and work in a confined space poses health and safety problems which may include: Presence or possible build up of a hazardous atmosphere Unexpected movement of equipment or materials
More informationConfined Spaces Guide
1 P a g e Confined Spaces Guide It is the responsibility of every occupant, owner, tenant, contractor, employee & visitor and ALL users of this complex to ensure they take all reasonably practical steps
More informationOperate Breathing Apparatus
Operate Breathing Apparatus This training is based on the National Unit of Competency: MSAPMOHS216A Operate breathing apparatus Training Course Overview You will learn about: Conduct pre donning checks
More informationPURPOSE To define the minimum requirements for controlling risks associated with persons entering or working in confined spaces.
PURPOSE To define the minimum requirements for controlling risks associated with persons entering or working in confined spaces. 1 SCOPE This procedure applies to all work or entry by any person into a
More informationConfined Space Management
Confined Space Management Latest revised date: October 26, 2011 Page 1 of 8 1.0 Preamble Memorial has implemented workplace procedures to prevent unauthorized and unsafe confined space entry to guide the
More information1 Purpose. 2 Responsibilities. 3 Policy Content ENVIRONMENTAL, HEALTH AND SAFETY STANDARDS. TITLE: CONFINED SPACE ENTRY Document Number: *
(Insert Company Logo) CORPORATE SAFETY MANUAL ENVIRONMENTAL, HEALTH AND SAFETY STANDARDS TITLE: CONFINED SPACE ENTRY Document Number: * Issue Date: Revision Date: * 1 Purpose The purpose of this policy
More informationCALIFORNIA STATE UNIVERSITY, LOS ANGELES WELDING, CUTTING, AND HOT WORK OPERATIONS. October 2007
CALIFORNIA STATE UNIVERSITY, LOS ANGELES WELDING, CUTTING, AND HOT WORK OPERATIONS October 2007 PROGRAM APPROVAL AND AUTHORIZATION James M. Rosser, President Date TABLE OF CONTENTS TITLE SECTION PURPOSE
More informationIn addition to this SOP, the policies and procedures of each operating company will be strictly observed by Rockwater personnel.
SOP FB-08 (Revised MAR 2014) STANDARD OPERATING PROCEDURES-FLOWBACK Hydrogen Sulfide Operations Section 1.0 Introduction and Background Rockwater Energy Solutions, Inc. (and all its affiliated and subsidiary
More informationANNEX AMENDMENTS TO THE INTERNATIONAL CODE FOR FIRE SAFETY SYSTEMS (FSS CODE) CHAPTER 15 INERT GAS SYSTEMS
Annex 3, page 2 ANNEX AMENDMENTS TO THE INTERNATIONAL CODE FOR FIRE SAFETY SYSTEMS (FSS CODE) CHAPTER 15 INERT GAS SYSTEMS The text of existing chapter 15 is replaced by the following: "1 Application This
More informationBP OIL -- TOLEDO REFINERY
Document Type: Procedure BP OIL -- TOLEDO REFINERY Refinery Wide Reference No.: SAF 086 Effective Date: October 3, 2011 Use of Nitrogen (N 2 ) Rev. No.: 7 Owner: Jon Parker Auth. By: D. C. Durnwald (Signature
More informationRecommended Facilitator Notes: (read the following text out-loud to participants while showing this slide)
Slide 1 Confined Space Entry for General Industry These materials have been developed based on applicable federal laws and regulations in place at the time the materials were created. The program is being
More informationANSI / ASSE Z88.2 American National Standard Practices for Respiratory Protection (1992 rev. versus 2015 rev.)
ANSI / ASSE Z88.2 BACKGROUND: A substantial body of research has been published since the 1992 revision of Z88.2. This information related to the proper use and performance of respiratory protection in
More informationSafety Manual Section 6 Confined Space
6. CONFINED SPACE ENTRY Introduction The following sections provide general guidelines and procedures for confined space entry. This section covers the following topics: Topic Page 6.1 Types of s... 6-2
More informationFACILITIES MANAGEMENT OFFICE OF ENVIRONMENTAL HEALTH AND SAFETY Confined Space Policy 11/21/14 Last Revision
FACILITIES MANAGEMENT OFFICE OF ENVIRONMENTAL HEALTH AND SAFETY Confined Space Policy 11/21/14 Last Revision 1.0 Intent To provide written procedures and guidelines for all University at Albany employees
More informationHEALTH AND SAFETY MANUAL
HEALTH AND SAFETY MANUAL Title: Hydrogen Sulfide (H 2 S) Safety Approved by: Greg Savoy Rev. 4/1/08 1 Purpose/Scope: The purpose of this program is to establish minimum requirements for site specific H
More informationCONFINED SPACE PROGRAM
CONFINED SPACE PROGRAM March 2017 CONTENTS Section 1: Introduction... 1 Section 2: Purpose... 1 Section 3: Definitions... 2 Section 4: Roles and Responsibilities... 4 Section 5: Testing and Monitoring...
More informationSTORM WATER RETENTION TANKS MAINTENANCE INFORMATION FOR HEALTH AND SAFETY FILE
STORM WATER RETENTION TANKS MAINTENANCE INFORMATION FOR HEALTH AND SAFETY FILE As required under the Construction (Design and Management) Regulations 1994 STORM WATER RETENTION (DRAINAGE) TANKS The information
More informationMANURE GAS DANGERS CHARACTERISTICS OF HYDROGEN SULFIDE (H 2 S)
MANURE GAS DANGERS Since the increased use of manure storage facilities in agriculture there have been numerous instances where a farmer, family member, or employee has been asphyxiated or succumbed to
More informationPSSI 36 General Confined Spaces, Tunnels, Culverts and Similar Spaces
1. SCOPE This document now includes provision for safe access to cable tunnels and culverts previously covered in PSSI 37 which is now withdrawn. The term Confined Space is defined in the Confined Spaces
More informationThe Corporation of the Town of Tecumseh
The Corporation of the Town of Tecumseh POLICY MANUAL POLICY NUMBER: 59/11 EFFECTIVE DATE: October 11, 2011 SUPERCEDES: PPC 23/07 - April 24, 2007 APPROVAL: RCM October 11, 2011 (RCM-343/11) SUBJECT: Confined
More informationVerification Of Calibration for Direct-Reading Portable Gas Monitors
U. S. Department of Labor Occupational Safety and Health Administration Directorate of Science, Technology and Medicine Office of Science and Technology Assessment Verification Of Calibration for Direct-Reading
More informationHot Work Program. University of Wisconsin-Platteville Reviewed 4/2016
Hot Work Program University of Wisconsin-Platteville Reviewed 4/2016 The purpose of the Hot Work Program is to establish safety procedures for employees, contractors, and subcontractors engaging in any
More informationSAFETY MANUAL PURGING, VENTING & DRAINING PROCEDURE TABLE OF CONTENTS 1. INTRODUCTION SCOPE DEFINITIONS PROCEDURE...
Page 1 of 11 TABLE OF CONTENTS 1. INTRODUCTION... 2 2. SCOPE... 2 3. DEFINITIONS... 2 4.... 3 5. RESPONSIBILTIES... 10 6. REFERENCES... 10 7. ATTACHMENTS... 11 8. APPENDICES... 11 Rev. Issue Date Amendment
More informationCONFINED SPACE ENTRY PROCEDURE
CONFINED SPACE ENTRY PROCEDURE June 2015 CONFINED SPACE ENTRY PROCEDURE Table of Contents I. Purpose II. Definitions III. Categories of Confined Spaces IV. Potential Hazards V. Confined Space Entry Work
More informationGuidance on Safe Entry into Inert Confined Spaces (Inert Entry), including Training, Procedures and Life Support Equipment
Guidance on Safe Entry into Inert Confined Spaces (Inert Entry), including Training, Procedures and Life Support Equipment Copyright Luno Systems Ltd 2018 1 of 17 Contents 1. Introduction 2. Documented
More informationBP OIL -- TOLEDO REFINERY
Document Type: Procedure BP OIL -- TOLEDO REFINERY Refinery Wide Procedure No.: SAF 086 Effective Date: May 9, 2016 Use of Nitrogen (N 2 ) Rev. No.: 9 Owner: Emily Stewart Auth. By: Chris Conley (Signature
More informationSafety Meeting Topic #11 Hazards of Confined Space
Safety Meeting Topic #11 Hazards of Confined Space OSHA defines confined spaces as work areas with certain features: large enough to enter and work in, limited entry and exit areas, and not designed to
More informationMAGB HEALTH and SAFETY GROUP Working In Confined Spaces
MAGB HEALTH and SAFETY GROUP Working In Confined Spaces SCOPE: This document represents best practice advice available and considered pertinent after consultation within the membership and incorporating
More informationTool Box Talk. Confined Space Entry New Construction Standard (2015)
Confined Space Entry New Construction Standard (2015) What s all this about Confined Space Entry and how does it affect the construction industry? On May 4, 2015 the Occupation Safety and Health Administration
More informationNiltox Breathing Air Purifier Range
Breathing Air Requirements The main standards affecting breathing air are BSEN529, EN12021 and COSHH. The requirements for a breathing air system are shown in the table opposite and the requirements for
More informationTYPICAL TOXIC GAS SYSTEM INSPECTION VIOLATIONS
TYPICAL TOXIC GAS SYSTEM INSPECTION VIOLATIONS The following is a list of typical violations often found by inspectors and a generic solution. You can use this list to improve the safety of your facility,
More informationCONFINED SPACE WRITTEN PROGRAM
CONFINED SPACE WRITTEN PROGRAM Maple River Public Schools ISD#2135 Confined Space Entry Plan (Permit Required) Maple River Public School Plan last updated: October, 2014 Authority and Scope Regulation:
More informationRespiratory Protection Self-Inspection Checklist
Respiratory Protection Self-Inspection Checklist Guidelines: This checklist applies to the use of either atmosphere-supplying or air-purifying respirators being worn, voluntarily or otherwise, for comfort
More informationWhen you complete this module you will be able to: Describe procedures needed to enter into, or work safely in confined spaces.
Confined Space Entry Learning Outcome When you complete this module you will be able to: Describe procedures needed to enter into, or work safely in confined spaces. Learning Objectives Here is what you
More informationA guide to Part 10 of the
OCCUPATIONAL HEALTH AND SAFETY DIVISION Welding, Cutting, Burning and Soldering A guide to Part 10 of the Occupational Safety General Regulations October 2007 A GUIDE TO PART 10 WELDING, CUTTING, BURNING
More informationAtmospheric Hazards. Hazardous Atmosphere 3/29/2017. Oxygen deficiency and enrichment Flammable gases and vapors Toxic contaminants
2017 Wisconsin Safety Council Safety & Health Conference, Presentation by Tim Gackle, OSHA Training Institute April 11, 2017 Atmospheric Hazards Oxygen deficiency and enrichment Flammable gases and vapors
More information2018 STATEMENTS OF FACT MINE RESCUE. 1. To test for methane, use a methane detector or chemical analysis.
2018 STATEMENTS OF FACT MINE RESCUE 1. To test for methane, use a methane detector or chemical analysis. 2. Carbon monoxide can be detected by means of carbon monoxide detectors, multigas detectors, or
More informationOSHA must prove. Confined Space Entry. Do you have an effective safety and health program? Some period of time later
Confined Space Entry OSHA background Definitions Program Contractors Permit Rescue Training Stories OSHA must prove Exposed employee Serious hazard Employer knowledge Feasible method to abate hazard More
More informationSafety Regulations and Procedures GENERAL SAFETY Confined Spaces - S New 11/96. To provide guidance for the safe entry of confined spaces.
CONFINED SPACES PURPOSE REGULATION To provide guidance for the safe entry of confined spaces. Washington Administrative Code - WAC 296-62, Part 'M,' Confined Spaces. RESPONSIBILITY Safety Services test
More informationPermit-Required Confined Spaces...29CFR
(Compliance Audit) Section (c) General Requirements 1) Has the employer performed a workplace inspection to determine if there are Yes No NA permit-required confined spaces (PRCS) present? 2) If the workplace
More informationManagement Plan for Confined Spaces
IEA, INC. B E M I D J I A R E A S C H O O L S Contact Us: BROOKLYN PARK OFFICE 9201 W. BROADWAY, #600 BROOKLYN PARK, MN 55445 763-315-7900 MANKATO OFFICE 610 N. RIVERFRONT DRIVE MANKATO, MN 56001 507-345-8818
More informationAdditional requirements for all types of entry are described in Section Determining the Applicable Entry Method
ENVIRONMENT, SAFETY & HEALTH DIVISION Chapter 6: Confined Space Entry Procedures Product ID: 155 Revision ID: 1948 Date published: 15 September 2017 Date effective: 15 September 2017 URL: http://www-group.slac.stanford.edu/esh/eshmanual/references/confinedprocedentry.pdf
More informationCalibration Requirements for Direct Reading Confined Space Gas Detectors
: Calibration Requirements for Direct Reading Confined Space Gas Detectors However, the definition of bump test has always been a little slippery. Some manufacturers differentiate between a bump test that
More informationRichland County School District One. Permit-Required Confined Space Entry Program (29 CFR Part )
Richland County School District One Permit-Required Confined Space Entry Program (29 CFR Part 1910.146) 1 PERMIT-REQUIRED CONFINED SPACE ENTRY PROGRAM FOR RICHLAND COUNTY SCHOOL DISTRICT ONE Purpose Richland
More informationSalt Lake Community College
Salt Lake Community College Confined Space Safety Program Prepared By: Environmental Health and Safety November 2004 Intended use of this program: The purpose of this program is to establish a Confined
More informationCONFINED SPACE ENTRY PROGRAM
CONFINED SPACE ENTRY PROGRAM In order to be in compliance with the proposed OSHA General Industry Standard 29CFR1910.146, Permit required Confined Spaces, it is necessary that Climate Engineers Inc. has
More informationH 2 S in the Oilfield Fact Sheet. Introduction to H 2 S. Where does H 2 S come from? Hazards of H 2 S
H 2 S in the Oilfield Fact Sheet Introduction to H 2 S Hydrogen Sulfide, or H 2 S, is an ever-increasing problem for workers involved in oil and gas exploration and production. H 2 S, however, is not just
More informationEntrant / Attendant / Supervisor Training
Entrant / Attendant / Supervisor Training 1 This material was produced under Grant SH-21000-10-60-F-29 from the Occupational Safety and Health Administration, U.S. Department of Labor. It does not necessarily
More informationConfined Spaces OSHA 1926 AA
Confined Spaces OSHA 1926 AA 1926.1201-1213 Confined Spaces Objectives: Understanding why the OSHA requirements are needed Identify four categories of hazards that may be present entering in confined spaces
More information