Kalibrgun Cricket series Regulated Airspace Increaser (RAI) with gauge, installing instruction by AS
|
|
- Horatio Parsons
- 5 years ago
- Views:
Transcription
1 Kalibrgun Cricket series Regulated Airspace Increaser (RAI) with gauge, installing instruction by AS First I must thank you for buying RAI. RAI is designed to use in the Kalibrgun Cricket series and nowhere else. All RAI units are pressure tested to over 300 bar (every unit you can see the detailed info of the pressure test) and that s why RAI is safe to use. If you receive somehow damaged RAI unit, please contact seller before install it. If RAI unit is modified somehow the seller doesn t take any responsible if something happens. You must understand that high pressures are extreme dangerous and can kill you if miss used. 1(11) RAI unit increases Cricket total airspace about 5 % and it shows the user what is the setting pressure of the regulator. Small pressure gauges doesn t have the best accurate (and there is some variation between the gauges), but it shows you does the regulator work and you know that standard un changed Cricket regulator setting is 110 Bar. When you know this you can estimate gauge s error rate and compensate it. Example standard cricket regulator setting was 110 bar ~ 1600 PSI but the gauge shows you 1800 PSI, then you know that error is about 200 PSI to up. Notice that when filling the gun the regulator doesn t work right (sometimes) and there must shot one or two times before it starts regulate right. When you start know your gun you know when it works right and when not. I think there was all the general talk and now let s start to install RAI. If you feel after reading this install instruction that you can t do the install safe, please contact seller who sold you RAI-unit and ask further instruction. I m sure they can help you out. 1. Before starting installing, make sure that gun is not loaded! 2. Helping assembling back first is good to mark barrel and air tube places. 2.1 Tapes 2.3 Cut the tape with sharp knife. Be careful to scratch anything. 2.2 Mark pressure tube and action housing
2 2(11) 2.4 Mark barrel align to barrel and monoblock 2.5 Measure pressure tube shift with RAI unit and mark align like picture 3. Remove the screw what retaining stock. 4. Remove stock (Notice mark tapes)
3 3(11) 5. Remove trigger link 6. Loosen the pressure tube bleed screw carefully. CAUTION! Do not under any circumstances open it fully open when you have pressure in the tube! Emptying the tube takes no more than two minute. 7. Before continue check from the pressure gauge that tube is fully empty
4 4(11) 8. Loosen screws what hold the pressure tube 9. Remove trigger mechanism assembly from other parts. It can be little bit stiff to remove but wiggling it little bit helps. Notice that I have cocked the gun just to prevent any damage to bolt.
5 5(11) 10. Remove the valve assembly from the pressure tube. CAUTION! pressure tube must be fully empty, before removing valve assembly! Valve assembly can be closed very hard, you can use example a hex tool helping to get it loose, but you must be careful and not to bend valve pin. 11. Install valve assembly to the RAI unit. Tight it fully in, but no need over tight. RAI unit threads are greased with silicone grease, but If you want you can add it to threads. NOTICE! use only silicone grease, nothing else! 12. Loosen four hex screws in the monoblock, don t remove just loosen.
6 6(11) 13. Slide pressure tube back so the RAI unit can installed easy and screw RAI unit to the pressure tube. Again tight it fully in, but no need over tight. Alignment should be like this 14. Slide pressure tube back it on place and align it like picture. Check also that the barrel align marks are on place.
7 7(11) 15. Tight monoblock screws so that barrel and pressure tube holds on place, no fully tight yet. 16. Install trigger mechanism assembly on its place. Again notice cocking. Alignment should look like this
8 8(11) 17. Tight pressure tube holding screws, first hex screw and then flat screw. 18. Tight the pressure tube bleed screw fully in and relatively tight. TIP, you can remove screw and add it some silicone grease help opening. 19. To prevent unwanted dry shot, release cocking keep cocking leveler and press trigger mechanism on forward, after you feel that cocking leveler resists you can slowly let it come on its normal place Hold 17.3 Slowly let leveler come on place That was hard to explain, I hope that you get the point Push forward
9 9(11) 20. Install trigger link on its place 21. Fit stock on the place and tight stock holding screw. When fitting stock on place, you must slightly slide monoblock to fit stock perfectly after stock is on place tight four monoblock screws. 22. Now you can remove all tapes and your Cricket should look like this, if not something went terribly wrong.
10 23. Installing cheek peace. Notice that I don t have composite stock model and I can t say how to cheek peace fit on that Wooden cheek peace doesn t fit perfectly without modifications 10(11) When you have cheek peace on place mark the outer edges of gauge with tape to cheek peace.
11 23.3. Carve with sharp blade from cheek peace inner surface, it s necessary to remove about 1-2 mm 11(11) Now RAI unit is fully fitted and it should look like this 24. Fill your gun and you are ready to shoot! Before start filling remember cock it, if you're not cock it, hammer presses the valve open and air just flows thru. I wish you happy shootings!
Monsoon repair/service helper. To high: Shoot a couple of shots until you get under 210bar, if it is higher than 210bar it will
Monsoon repair/service helper 1. Pressure: Min 180bar Max 210bar To low: Charge with air To high: Shoot a couple of shots until you get under 210bar, if it is higher than 210bar it will Not be able to
More informationInstallation Procedure for your Disco Double Kit, by Airgun Lab, LLC.
Disco Double Installation Instructions Copyright Airgun Lab LLC Rev D January 2016 page 1 of 6 Installation Procedure for your Disco Double Kit, by Airgun Lab, LLC. Step 1, gather tools. Tools required
More informationWelcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles.
Welcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles. By using only the highest quality materials such as aircraft grade aluminum, aluminumbronze,
More informationFX IMPACT OWNER S MANUAL
made in sweden FX IMPACT OWNER S MANUAL Warranty Information All FX Airguns carry a One Year Warranty against faulty workmanship and defective materials. If it becomes necessary, first contact the dealer
More informationTABLE OF CONTENTS SAFETY FIRST!...3 BASIC OPERATION...4 ADJUSTMENTS...5. Cocking Pressure...5. Three-Way Valve Adjustment...6
TABLE OF CONTENTS SAFETY FIRST!...3 BASIC OPERATION...4 ADJUSTMENTS...5 Cocking Pressure...5 Three-Way Valve Adjustment...6 External Three-Way adjustment...6 In-Line Regulator...6 Ram to Cocking Block
More informationTECH SHEET ORANGE PIVOT TOOL INSTRUCTIONS
page 1 ORANGE PIVOT TOOL INSTRUCTIONS This is a guide of how to change the pivot bearings on an Orange frame with a bore style pivot axle. 4 8 Bore Type Pivot Axle Horiz-Hold Type Pivot Axle Please read
More informationAR STYLE FIREARMS OWNER'S MANUAL: OPERATION, HANDLING, DISASSEMBLY / REASSEMBLY & SAFETY INSTRUCTIONS
AR STYLE FIREARMS OWNER'S MANUAL: OPERATION, HANDLING, DISASSEMBLY / REASSEMBLY & SAFETY INSTRUCTIONS - DO NOT DISCARD THIS MANUAL - READ THIS MANUAL CAREFULLY, PAYING CLOSE ATTENTION TO THE INSTRUCTIONS
More informationSAFETY RULES WARNING: READ THESE SAFETY RULES & OPERATORS MANUAL BEFORE HANDLING YOUR FIREARM
SAFETY RULES WARNING: READ THESE SAFETY RULES & OPERATORS MANUAL BEFORE HANDLING YOUR FIREARM Never point a firearm at anyone and always keep the muzzle pointed in a safe direction. Always treat all firearms
More informationFIRESTORM. Assembly Instructions. Electric Upgrade Kit for the Autococker. Designed & Manufactured by PGI
FIRESTORM Electric Upgrade Kit for the Autococker Assembly Instructions Designed & Manufactured by PGI Table of Contents Introduction 1 Safety 1 Parts Diagram 2 Parts Diagram Listing 2 Getting Started
More informationWelcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles.
Welcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles. By using only the highest quality materials such as aircraft grade aluminum, aluminumbronze,
More informationOWNER S MANUAL READ THIS MANUAL BEFORE USING YOUR NEW AIRGUN
OWNER S MANUAL READ THIS MANUAL BEFORE USING YOUR NEW AIRGUN FX SUPER SWIFT Table of Contents Warranty Specifications General Instructions Operating Instructions Trigger Adjustments Care & Maintenance
More informationVR1 Owner s Manual. Vigilance Rifles, Inc Plum Lane Redlands, CA P F
VR1 Owner s Manual Vigilance Rifles, Inc. 1653 Plum Lane Redlands, CA 92374 P 909.307.8877 F 909.307.8866 www.vigilancerifles.com INTRODUCTION: Vigilance Rifles offers a new line of Semi-Automatic Rifles
More informationPISTOL CALIBER AR STYLE FIREARMS
PISTOL CALIBER AR STYLE FIREARMS OWNER'S MANUAL: OPERATION, HANDLING, DISASSEMBLY / REASSEMBLY & SAFETY INSTRUCTIONS - DO NOT DISCARD THIS MANUAL - READ THIS MANUAL CAREFULLY, PAYING CLOSE ATTENTION TO
More informationInstalling N-Strike Recon CS-6 Stage 1 and Stage 2 Performance Kits
Installing N-Strike Recon CS-6 Stage 1 and Stage 2 Performance Kits The Nerf N-Strike Recon CS-6 is a currently available blaster that is relatively easy to modify. The guys at Orange Mod Works have produced
More informationThe P-Rod Double by The Airgun Lab Installation Instructions Revision F 08/01/2016 page 1 of 18
Installation Instructions Revision F 08/01/2016 page 1 of 18 Safety Warning, Terms and Conditions: Each P-Rod Double kit has been designed, manufactured, and tested to function with a standard Benjamin
More informationNow you can remove the 4 screws on the back of the housing to reveal the AFC Diaphragm. One of these is a break off/tamper proof cap screw as well.
There are a few things you can mod easily that increase rack travel in the pump through the AFC. One is the cupped washer on the side of the diaphragm near the spring. Another is the barrel of the afc
More information8. Carefully layout all the parts of the reservoir setup and clean any dirt, grime or dust from the parts. ( image 8 ) 8
INSTRUCTIONS TO SERVICE AMADAXTREME SHOCKS 2.0 REMOTE RES AUSTRALIAN VERSION PART 1 - SERVICE THE RESERVOIR 1.Prior to cleaning the shock check for any leaks or signs of damage to the res, lines, bushes
More informationHATFIELD. Continuing the Tradition SEMI-AUTOMATIC SHOTGUN INSTRUCTION MANUAL
HATFIELD Continuing the Tradition SEMI-AUTOMATIC SHOTGUN INSTRUCTION MANUAL READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM SAFETY HANDLING RULES 1.Always keep the
More informationHW90 Gas ram Removal
HW90 Gas ram Removal ************************************************************* * Information below shows how to remove the gas ram from the Weihrauch HW90 air rifle. The strip was performed on a UK
More informationMAINTENANCE PROCEDURE FOR X 650
MAINTENANCE PROCEDURE FOR X 650 X 650 25. juli 2005-1/6 MAINTENANCE PROCEDURE FOR X 650 2 ND STAGE WARNING: This maintenance procedure is only for appointed Scubapro technicians that completed a course
More informationMODEL 1400 E USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM.
ARMSCOR MODEL 1400 E USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM. DISCHARGING FIREARMS IN POORLY VENTILATED AREAS, CLEANING FIREARMS
More informationRADROVER REAR RACK INSTALLATION MANUAL
RADROVER REAR RACK INSTALLATION MANUAL WWW.RADPOWERBIKES.COM We are here to help! Please contact us at SUPPORT@RADPOWERBIKES.COM or 1-800-939-0310 if you have questions. REV022216 Welcome Thanks you for
More informationApex M&P Barrel Fit Guide ALL OF THE FOLOWING OPERATIONS ARE TO BE DONE WITH ABSOLUTELY ZERO LIVE AMMUNITION PRESENT.
Familiarization Free floating barrels like most polymer frame pistols have, use 6 contact points o Barrel hood The extension of the chamber coming back over the top of a chambered round to make contact
More informationSanta Fe Cycles Assembly Guide Introduction
Santa Fe Cycles Assembly Guide Introduction Congratulations on your purchase of your new Santa Fe bicycle. You have purchased a bicycle that has many features and qualities. Please take a few minutes and
More informationPlease visit our website at and leave your comments.
We promise our customers the best services and premium quality products with value. MODIFY and its logo are registered trademarks. Please visit our website at www.modify.com.tw and leave your comments.
More informationTable of Contents. Rules of Safe Shooting 3. Getting Started 4. Charging the Rifle 5. Loading 6. Safety 7. Looking After Your FX 8.
GLADI8OR Owner s Manual Table of Contents Rules of Safe Shooting 3 Getting Started 4 Charging the Rifle 5 Loading 6 Safety 7 Looking After Your FX 8 Lubrication 8 Power Adjustment 9 Adjusting The Trigger
More informationsuperposed Over and Under Shotgun Lightning, Standard and Magnum Models 12, 20, 28 Gauge and.410 Bore Browning Gun Parts Price List
, 0, 8 Gauge and.40 Bore Prices F.O.B. point of shipment subject to change without notice. Prices effective January, 03. part description msrp (US$) B333004 BARREL PLATE SCREW $ * B333000 BARREL PLATE
More informationCleaning rod: spring steel, stainless steel or carbon fibre cleaning rod - only use a one-piece rod. Avoid using snakes.
Telemark Biathlon Where performance and precision come together http://telemarkbiathlon.com Rifle Cleaning Date : July 19, 2013 Anschutz Rifle Manual - Click Here Izhmash 7-3 Rifle Manual - still looking
More informationCONTENTS. Safety & general information. Filling your air rifle with compressed air. Loading your rifle. Pellet recommendations. Fitting a rifle scope
TSAROFFICIAL Edition 14 HANDBOOK CONTENTS Never point your airgun at anyone or anything other than a legitimate target. Safety & general information 2 Filling your air rifle with compressed air 3 Always
More informationWelcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles.
Welcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles. By using only the highest quality materials such as aircraft grade aluminum, aluminumbronze,
More information;\- ,.. SAFETY WARNING: Failure to obey a safety warning may result In Injury to you or. T to others. T LOADED AND THE SAFETY IS IN THE
,.. SAFETY WARNING: Failure to obey a safety warning may result In Injury to you or T to others. '-"f"oi:ti,., WARNING INSTRUCTIONS FOR THE MODEL 1400 CAUTION-ALWAYS KEEP THE T MUZZLE POINTED IN A SAFE
More informationSKYBIRD TRAP OWNER S / OPERATOR S MANUAL PARTS AND ASSEMBLY INSTRUCTIONS
SKYBIRD TRAP PART NO. 40903 OWNER S / OPERATOR S MANUAL PARTS AND ASSEMBLY INSTRUCTIONS WARNING: THIS MACHINE CAN CAUSE SERIOUS INJURY OR DEATH! THOROUGHLY READ INSTRUCTIONS AND SAFETY INFORMATION BEFORE
More informationFinal Assembly Instructions Bikes with Quill Stems
Final Assembly Instructions Bikes with Quill Stems Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert
More informationQUIK-jet Micro-Injection System
QUIK-jet Micro-Injection System Training Manual Revision Date: 11/12/07 Table of Contents Subject Headings Pages Introduction 3 Parts of the QUIK-jet Kit 4 QUIK-jet Assembly and Setup 5-6 3 Easy Steps
More informationM16 R / M1600 R USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM.
ARMSCOR M16 R / M1600 R USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM. DISCHARGING FIREARMS IN POOLY VENTILATED AREAS, CLEANING
More informationWelcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles.
Welcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles. By using only the highest quality materials such as aircraft grade aluminum, aluminumbronze,
More informationWARNING OWNER S MANUAL WARSENSOR WSP PAINTBALL PISTOL
WARSENSOR WSP PAINTBALL PISTOL OWNER S MANUAL WARNING WARSENSOR PAINTBALL MARKERS ARE NOT A TOY. ANY MISUSE MAY CAUSE SERIOUS INJURY OR DEATH. THE USER AND ANY PERSON WITHIN RANGE MUST WEAR EYE PROTECTION
More informationPR4 Installation, Operation & Maintenance Instructions (DOT Certification Included)
PR4 Installation, Operation & Maintenance Instructions (DOT Certification Included) March 2006 Form FVC 054 Rev. 6 KEEP THIS DOCUMENT WITH THE PRODUCT UNTIL IT REACHES THE END USER. The Passive - R4 device
More informationYou have decided to buy an LP 10 E by STEYR SPORTWAFFEN the new dimension of match air pistols!
Congratulations! You have decided to buy an LP 10 E by STEYR SPORTWAFFEN the new dimension of match air pistols! The world-beating air pistol with electronic trigger! The STEYR LP 10 probably is the most
More informationFinal Assembly Instructions Bikes with Threaded Headsets
Final Assembly Instructions Bikes with Threaded Headsets Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our
More informationCRUZBIKE Quest 2.0 Assembly
CRUZBIKE Quest 2.0 Assembly CRUZBIKE Quest 2.0 Assembly... 1 General notes on assembly... 2 Un box and evaluate the frame and major parts... 2 Unfold the rear swing arm and arrange the frame... 3 Rear
More informationTactical Sniper air rifle & carbine
Tactical Sniper air rifle & carbine User instruction manual Fill pressure: 200 bar (approximately 2,900 psi) Rev 4/17 Contents Rules of safe shooting... 3 Filling your rifle... 4-5 Loading the magazine...
More informationParts List. 7. Handlebars 8. Grips 9. Handlebar Stem 10. Front Brake 11. Front Wheel 12. Crank 13. Chain
Woodworm Cruise Parts List 1. Free Wheel with Rear Hub 2. Fenders 3. Fender Stay 4. Quick Release 5. Saddle 6. Seat Post 7. Handlebars 8. Grips 9. Handlebar Stem 10. Front Brake 11. Front Wheel 12. Crank
More informationAttention: This operator s manual should be read carefully before using the air rifle. ENGLISH
Attention: This operator s manual should be read carefully before using the air rifle. 05-2004 25 Important measures when using arms: TABLE OF CONTENTS All firearms can be dangerous; they should be used
More informationWelcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles.
Welcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles. By using only the highest quality materials such as aircraft grade aluminum, aluminumbronze,
More informationTHE OWNER'S MANUAL IS IN TWO VOLUMES: VOLUME 2 TECHNICAL SPECIFICATIONS - ASSEMBLY PROCEDURE ZODIAC
CAUTION NOTICE: CAREFULLY READ THIS MANUAL BEFORE OPERATING YOUR BOAT. THIS OWNER S MANUAL IS IN TWO VOLUMES THAT MUST BE KEPT TOGETHER. THE OWNER'S MANUAL IS IN TWO VOLUMES: - VOLUME 1 DEALS WITH OPERATING
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Ballpark Classics Baseball Game MLB Edition Figure B Read the instructions completely before beginning g assembly. You will need a Phillips screwdriver. 1. Remove the game from the
More informationSTRIBOG GRAND POWER. The INSTRUCTIONS FOR USE, MAINTENANCE AND SAFETY. 1
instructions The for use, maintenance STRIBOG and safety hestribog GRAND POWER INSTRUCTIONS FOR USE, MAINTENANCE AND SAFETY www.grandpower.eu 1 The STRIBOG Dear Customer, Thank you for purchasing a semi-automatic
More informationFinal Assembly Instructions Bikes with Threaded Headsets
Final Assembly Instructions Bikes with Threaded Headsets Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our
More informationBedienungsanleitung / Operating Instructions / Instrucciones de uso / Mode d emploi / Istruzioni d'uso
Bedienungsanleitung / Operating Instructions / Instrucciones de uso / Mode d emploi / Istruzioni d'uso Pressluftgewehr LG30 LG30 Junior cal..177 (4,5mm) Marketing/Vertrieb Service/Technik Carl Walther
More informationstormrider Instructions for Use Version 08/2017
stormrider EN Instructions for Use Version 08/2017 INTRODUCTION DESCRIPTION SAFETY INSTRUCTIONS TECHNICAL DATA HANDLING & OPERATION CARE & MAINTENANCE TROUBLESHOOTING DESCRIPTION Front Sight Barrel Rear
More informationPaintball Marker. User s Manual. Direct Feed. SC: Stock Class. VSC: Vertical Air Stock Class. 530 South Springbrook Road Newberg, OR 97132
Paintball Marker User s Manual Direct Feed SC: Stock Class 530 South Springbrook Road Newberg, OR 97132 VSC: Vertical Air Stock Class www.phantomonline.com Component Concepts, Inc., 530 South Springbrook
More informationDisassembly and Assembly of FDAR High-pressure Manual Pump (v. 1.0) IMPORTANT What s included:
Disassembly and Assembly of FDAR High-pressure Manual Pump (v. 1.0) (available from Flying Dragon Air Rifles: http://flyingdragonairrifles.org/high_pressure_pcp_pump.html) With the rapid success of the
More informationFiber Optic Lighted Bubbler Spillway Pot (DLP-45) Installation Manual
Fiber Optic Lighted Bubbler Spillway Pot (DLP-45) Installation Manual 27.75 23.75 25.50 20.75 Specifications: 8-13 GPM 100 strand fiber - Bubbler 75 strand fiber - Spillway Light Bar 45 ft. fiber tail
More informationTIPPMANN 98 CUSTOM. Owner s Manual CO2 POWERED PAINTBALL GUN
TIPPMANN PNEUMATICS, INC. Get Your ur Heart t Pound unding With h A Tippmann! WARNING: This paintball marker/gun is not a toy nor is it intended for unsupervised use by persons under the age of 18 years.
More informationLight Hunter Recluse Dragon Claw
SAM YANG Light Hunter Recluse Dragon Claw User instruction manual Light Hunter Recluse Dragon Claw Fill pressure: 206 bar (approximately 3,000 psi) Rules of safe shooting... 3 Safety... 4 Installing cocking
More informationKHANSHOTGUNS. Thank you for choosing KHANSHOTGUNS 20 Gauge over & under shotgun
Thank you for choosing KHANSHOTGUNS 20 Gauge over & under shotgun Your over & under shotgun represents a piece of rich history of quality firearms design and manufacture. During the manufacturing process,
More informationASSEMBLY INSTRUCTIONS FOR EMPIRE TERMINATOR / RECON HYBRID RECURVE CROSSBOW LINE
OWNER S INSTRUCTION & SAFETY MANUAL ASSEMBLY INSTRUCTIONS FOR EMPIRE TERMINATOR / RECON HYBRID RECURVE CROSSBOW LINE PRESENTED BY SA SPORTS LLC. IMPORTANT! Read the following Instructions carefully before
More informationShooters Ridge 10/22 Magazine Troubleshooting Guide (Questions and answers apply to all SR 10/22 magazines unless noted)
Shooters Ridge 10/22 Magazine Troubleshooting Guide (Questions and answers apply to all SR 10/22 magazines unless noted) BACKGROUND This troubleshooting guide is designed to help consumers with any problems
More informationMFI SIG 556P/2 Hand Guard Retaining Ring Installation Instructions
MFI SIG 556P/2 Hand Guard Retaining Ring Installation Instructions 100% MADE IN THE USA! All NFA Rules Apply. First of all I would NOT even offer these parts if I did not feel that 98% of you SIG 556 owners
More informationModular training weapon Owners manual
Modular training weapon Owners manual MTW Basic Features Thank you for joining the Wolverine family! We hope you will enjoy your new Modular Training Weapon. Please read the Owners Manual carefully before
More informationPaintball Marker. User s Manual. 530 South Springbrook Road Newberg, OR 97132
Paintball Marker User s Manual 530 South Springbrook Road Newberg, OR 97132 Component Concepts, Inc., 530 South Springbrook Road, Newberg, OR 97132 Phone: (503) 554-8095 Fax: (503) 554-9370 www.phantomonline.com
More information500SE SECOND STAGE SERVICE PROCEDURE
500SE SECOND STAGE SERVICE PROCEDURE This 500SE Service Procedure conveys a list of components and service procedures that reflect the 500SE as it was configured at the time of this writing. CONTENTS TROUBLESHOOTING...
More informationInstallation, Operation, and Maintenance Manual. Welker Constant Pressure Cylinder With Welker Magnetic Indicator (With Gravity Mixer) Model CP2GM-HP
Installation, Operation, and Maintenance Manual Welker Constant Pressure Cylinder With Welker Magnetic Indicator (With Gravity Mixer) Model The information in this manual has been carefully checked for
More informationWelcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles.
Welcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles. By using only the highest quality materials such as aircraft grade aluminum, aluminumbronze,
More informationAPP pumps APP and APP Disassembling and assembling
Service guide APP pumps APP 11-13 and APP 16-22 Disassembling and assembling hpp.danfoss.com Table of Contents Contents 1. Introduction... 2 2. Disassembling the pump... 3 3. Assembling the pump... 6 4.
More informationATD LB PRESSURE BLASTER INSTRUCTION MANUAL
ATD-8402 90LB PRESSURE BLASTER INSTRUCTION MANUAL SAVE THESE INSTRUCTIONS SAFETY INSTRUCTIONS FOR SANDBLASTER 1. Before opening the tank release the air pressure on the sand tank. To do this, turn off
More informationInstallation, Operation, and Maintenance Manual
Installation, Operation, and Maintenance Manual Welker Probe Instrument Regulator Model The information in this manual has been carefully checked for accuracy and is intended to be used as a guide for
More informationReview of the Mauser Sr -Pro Tactical- from including the Swiss Arms 4x32 scope with mount rings.
Review of the Mauser Sr -Pro Tactical- from www.begadishop.de including the Swiss Arms 4x32 scope with mount rings. In this review I will go through the following points: Chassis/the stock Outer barrel
More informationWelcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles.
Welcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles. By using only the highest quality materials such as aircraft grade aluminum, aluminumbronze,
More informationTrike-Bike Assembly Manual
Be sure to check our website for more instruction details, videos and photographs as well as a complete listing of each Nut and Bolt for the Trike Bike. www.trike-bike.com.au Go to the page marked ASSEMBLY
More informationCentriFlow Meter Integrated Air Entrainment System
CentriFlow Meter Integrated Air Entrainment System INSTALLATION & OPERATION MANUAL January 2004 Revision 021-4 EASTERN INSTRUMENTS 416 LANDMARK DR. WILMINGTON, NC 28412 910-392-2490 Fax: 910-392-2123 website:
More information4400 TwinHybrid Gas Seal
4400 TwinHybrid Gas Seal EQUIPMENT PREPARATION MECHANICAL SEAL INSTALLATION INSTRUCTIONS 1 2 200.005" 0,13 mm 125 µ" 3,2 µm R a 3 4 32 µ" 0,8 µm R a 1000 ±.002" 0,05mm CAUTIONS These instructions are general
More informationINSTRUCTION MANUAL HATSAN ARMS COMPANY HATSAN GLADIUS & HATSAN BULLBOSS PCP AIR RIFLE PLEASE READ THIS MANUAL BEFORE USING YOUR AIR GUN
HATSAN ARMS COMPANY Serious. Solid. Impact. HATSAN GLADIUS & HATSAN BULLBOSS PCP AIR RIFLE INSTRUCTION MANUAL PLEASE READ THIS MANUAL BEFORE USING YOUR AIR GUN Thank you for choosing the Hatsan Gladius
More informationThreaded Closures Installation, Operation & Maintenance
Howard Street Bulletin TT Louisville, KY 0 USA Revised Jan 0 Phone 0--0 Fax 0--00 Threaded Closures Installation, Operation & Maintenance Caution: Operating a closure can be a hazardous activity and certain
More informationWindy City II. User instruction manual WARNING: Fill pressure: 200 bar (approximately 2,900 psi)
Windy City II User instruction manual Rules of safe shooting... 2 Filling the rifle... 3-4 Loading the magazine... 5-6 Inserting the magazine... 7 Adjusting the trigger... 7-8 Safety... 9 Warranty... 10
More informationGurney Flap for WRX and STI w/low Profile Trunk Spoiler
Gurney Flap for 2015+ WRX and STI w/low Profile Trunk Spoiler 2017-12-05 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced
More informationFinal Assembly Instructions Bikes with 16 Wheel Size
Final Assembly Instructions Bikes with 16 Wheel Size Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert
More informationArmorer s Handgun Sight Tool
Armorer s Handgun Sight Tool Product #710905 Instructions #1054680 Rev. B 2 Top Knobs Height Adjustment Screw Adjustment Wheel Front Pusher Block Top Carriage Assembly 2 Front Pusher Block Screws Bottom
More information3190A NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS. Series MODEL NO
NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS Series 30A Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
More information600 / 600FC OWNER'S MANUAL
PROGRESSION 600 / 600FC OWNER'S MANUAL Issue 2 / Version E - Dec. 10, 1997 Copyright 1997 GAMMA Sports - All Rights Reserved PROGRESSION 600 / 600FC OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY
More informationPressure Dump Valve Service Kit for Series 2300 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit
More informationINSTRUCTION MANUAL CZ 630/631
INSTRUCTION MANUAL CZ 630/631 Before handling the air rifle read this manual carefully and observe the following safety instructions. Improper and careless handling of the air rifle could result in unintentional
More information1.0 - OPENING AND CLOSING THE DOOR
The purpose of this manual is to provide the user with instructions on how to safely open and close, how to conduct routine maintenance, and how to install the PEI TWINLOCK Closure on a pressure vessel.
More informationLJ1-25 LouieJRtm Tapping Machine
1/21/08 WARNING: Before using this product, read owners manual and follow all Safety Rules and Operating Instructions. LJ1-25 LouieJRtm Tapping Machine OPERATIONS MANUAL & OPERATING INSTRUCTIONS 30230
More information!!!! SERVICE MANUAL PRESSURE POT 2 GALLON. Service Manual: LT Washington St 931 Progress Ave., #7
EXEL North America, Inc. EXEL Industrial Canada, Inc. 1310 Washington St 931 Progress Ave., #7 West Chicago, IL 60185 Scarborough ONT, M1G 3V5 Ph : (800) 573 5554 Ph : (800) 450 0655 Fx : (800) 664 1511
More informationSEMIAUTOMATIC SHOTGUN OWNER'S MANUAL
SEMIAUTOMATIC SHOTGUN OWNER'S MANUAL ARMSAN@ARMSAN.COM TECHNICAL DATA Caliber :12 gauge / 20 gauge / 28 gauge Operation: Semi-Automatic, Gas Operated System Barrel Length: 20 (51cm), 24 (61cm), 26 (66cm),
More informationATTENTION! Use only clean compressed air to fill the Lelya 2.0! Rifle Schematic
Thank you for purchasing the new Lelya 2.0 (Леля 2.0.). In this manual you will find directions for operating this unique PCP rifle В Slavic mythology Lelya - the goddess of spring, the patroness of lovers,
More informationPLEASE READ THIS MANUAL BEFORE USING YOUR AIR GUN
HATSAN ARMS COMPANY Serious. Solid. Impact. AT44-PA Series PCP Air Rifle INSTRUCTION MANUAL PLEASE READ THIS MANUAL BEFORE USING YOUR AIR GUN Thank you for choosing AT44PA PCP air rifle. Always use caution
More information5 Gallon Pressure Pot with HVLP Spray Gun and Hose
California Air Tools 5 Gallon Pressure Pot with HVLP Spray Gun and Hose Model No. 365 Technical Data Type of feed.pressure Maximum pressure in the tank... 0,413Mpa (60PSI) Working pressure in the tank.0,
More informationFront derailleur. Dealer's Manual SORA FD-R3000 FD-R3030 CLARIS FD-R2000 FD-R2030. ROAD MTB Trekking. City Touring/ Comfort Bike DM-RBFD001-01
(English) DM-RBFD001-01 Dealer's Manual ROAD MTB Trekking City Touring/ Comfort Bike URBAN SPORT E-BIKE Front derailleur SORA FD-R3000 FD-R3030 CLARIS FD-R2000 FD-R2030 CONTENTS IMPORTANT NOTICE... 3 TO
More information! WARNING! IMPORTANT HPA AIR TANK SAFETY INSTRUCTION AND GUIDELINES ! WARNING! IMPORTANT SAFETY INSTRUCTION AND GUIDELINES
! WARNING! IMPORTANT SAFETY INSTRUCTION AND GUIDELINES! WARNING! IMPORTANT HPA AIR TANK SAFETY INSTRUCTION AND GUIDELINES This Paintball Marker is NOT A TOY. Misuse can cause serious injury or death. It
More information2.5 & 5.0 GALLON PRESSURE TANKS
2.5 & 5.0 GALLON PRESSURE TANKS Includes: MODEL 7025 MODEL 7026 MODEL 7027 MODEL 7028 2.5 Gallon Single Regulation (NON A.S.M.E.) 2.5 Gallon Dual Regulation (NON A.S.M.E.) 5.0 Gallon Single Regulation
More information! WARNING. Model PFC-1-G (direct acting) PFC-1-GR (reverse acting) Modulating Pneumatic Liquid Level Controls INSTRUCTION MANUAL MM-110B
INSTRUCTION MANUAL MM-110B Model PFC-1-G (direct acting) PFC-1-GR (reverse acting) Modulating Pneumatic Liquid Level Controls APPLICATIONS: Use with other pneumatic devices, for liquid level sensing in
More informationUNPACKING AND ASSEMBLING YOUR DIAMONDBACK ROAD BIKE
EMAIL SIGNUP BIKE REG SEARCH BIKES THE RIDE HEALTH FITNESS SKILLS SHOP MAINTENANCE CYCLING 101 RIDERS LIKE YOU TEAMS SUPPORT UNPACKING AND ASSEMBLING YOUR DIAMONDBACK ROAD BIKE 1. Begin by carefully cutting
More information1911A1 45 Cal Teardown
1911A1 45 Cal Teardown 1911A1/1911R1 Sidearm and Clones Written By: Wraithvenge ifixit CC BY-NC-SA www.ifixit.com Page 1 of 14 INTRODUCTION The 1911 Pistol, unquestionably the greatest sidearm ever made.
More informationConstant Pressure Crude Oil Container Model CPCCP
Installation, Operations, and Maintenance Manual Constant Pressure Crude Oil Container Model CPCCP The information in this manual has been carefully checked for accuracy and is intended to be used as a
More informationAK / Instruction Manual
AK / Instruction Manual BEFORE USING THIS PRODUCT, CAREFULLY READ THOUGH MANUAL AND RETAIN IT FOR FUTURE REFERENCE. ECHO1USA AUTOMATIC ELECTRIC GUNS ARE INTENDED FOR AGES 18 AND ABOVE. THIS PRODUCT MAY
More informationDisassembly, Assembly, and Cleaning of M16A4/M4
Table of Contents iii Disassembly, Assembly, and Cleaning of M16A4/M4 By: George Carter Chris Talbott Jeremy Tinker Table of Contents Introduction... vii Disassembly... 3 Clearing the Magazine... 3 Retaining
More informationParts of the Gun. Specifications XCR-C XCR-L. Optic Rail. Charging Handle. Sling Loop. Accessory Rails. Crane Stock. Flash Hider. Stock Pad.
BEFORE USING THIS PRODUCT, CAREFULLY READ THOUGH MANUAL AND RETAIN IT FOR FUTURE REFERENCE. ECHO1USA AUTOMATIC ELECTRIC GUNS ARE INTENDED FOR AGES 18 AND ABOVE. THIS PRODUCT MAY CAUSE SERIOUS INJURY IS
More information