REGULATORS FOR SPECIFIC APPLICATIONS

Transcription

1 SINGLE-STAGE REGULATORS FOR NITROUS OXIDE AND CARBON DIOXIDE (MODELS SG9011, SG9012, SG9014) Nitrous Oxide and Carbon Dioxide frequently cause ordinary regulators to freeze up. Models SG9011, SG9012 and SG9014 will handle these gases at flow rates up to 100 scfh at 70 F without freeze-up and without the need for electrical connections. Note: These regulators are not manufactured to meet FDA standards and should not be used for medical gases. Regulators for medical gases are shown on page 30. Filter in Seat Assembly traps foreign matter, extends regulator life and reduces maintenance. Unique Regulator Design operates at flow rates up to 100 scfh at 70 F without freeze-up. Pressure Relief Valve protects regulator and downstream system from overpressurization. Maximum Inlet Pressure: 1500 psig Inlet Pressure Gauge: psig Maximum Flow Rate: 100 scfh Range: See Table I Gauge/Flowmeter: See Table I Gauge Size: 2" Dial Inlet Connection: CGA 326 for Nitrous Oxide CGA 320 for Carbon Dioxide Outlet Connection: 1 4" NPT female Relief Valve: Self-Reseating 200 psig Approximate Weight: 3 lbs Body and Bonnet: Aluminum Gauges: Chrome-Plated Brass Seat: Polyurethane Seals and Diaphragm: Neoprene Flowmeter (Model SG9012): Chrome-plated Brass with Lexan plastic tube and shield SG9014 Regulator SG9012 Regulator Gauge or Configuration Range Flowmeter SG9011-(CGA) Regulator with flow gauge* scfh scfh SG9012-(CGA) Regulator with flowmeter scfh scfh SG9014-(CGA) Regulator with pressure gauge psig psig * Note: A Regulator equipped with a flow gauge is not accurate when a backpressure in excess of 2 psig exists at the outlet. In applications where backpressure in excess of 2 psig can be expected, a regulator with a flowmeter should be used. Teflon Washers for CGA 320 (package of 25) SG ADVANCED Specialty Gas

2 SINGLE-STAGE REGULATORS FOR ATOMIC ABSORPTION, ACETYLENE (MODEL AG9048) This regulator is specifically designed for use with Atomic Absorption or Technical Grades of Acetylene. Although similar to our Model APD diffusion resistant regulator, its delivery pressure is limited to 15 psig. Limited Pressure Adjustment does not allow delivery pressure above 15 psig as recommended for Acetylene service. Type 316L Stainless Steel Diaphragm minimizes diffusion of air into regulator and eliminates off gassing associated with elastomeric diaphragms, thus maintaining gas purity. Cartridge (Encapsulated) Seat Assembly provides for ease of maintenance and repair. Filter in Seat Assembly traps foreign matter, extends regulator life and reduces maintenance. Threaded Holes in Rear of Regulator permit front panel mounting. 1 8" NPT Female Bonnet Vent Port allows bonnet to be connected to a vent line or disposal system as a precaution in the unlikely event of a diaphragm failure. Red-Lined Pressure Gauge provides visual indication should delivery pressure exceed allowable withdrawal pressure of 15 psig. Maximum Inlet Pressure: 300 psig Inlet Pressure Gauge: psig Pressure Range: 2 15 psig Pressure Gauge: 0 30 psig red-lined above 15 psig Filter: 10 micron Gauge Size: 2" Dial Operating Temp. Range: -40 F to +140 F Flow Coefficient: Regulator: Cv = 0.17 Outlet Valve: Cv = 0.4 Inlet Connection: CGA 510 Outlet Connection: 1 4" NPT male (on outlet valve) Supply Pressure Effect: 1 psi per 100 psi Approximate Weight: 3 lbs. Optional SG6545 Flash Arrestor: Maximum Operating Pressure: 250 psig Maximum Flow Capacity: 40 scfh acetylene Pressure Drop: 5 40 scfh Connections: 1 4"NPTF x 1 4" NPTM AG9048 Regulator SG6545 Optional Flash Arrestor REGULATORS FOR SPECIFIC APPLICATIONS Mounting Ring permits regulator to be panel mounted Acetylene Flash Arrestor prevents flashback into cylinder. AG9048 Body and Bonnet: Brass Bar Stock Outlet Valve and Gauges: Brass Filter: Nickel-Plated Sintered Bronze Brass and Stainless Steel Seat and Seals: Teflon Diaphragm: Type 316L Stainless Steel Optional SG6545 Flash Arrestor: Body and Fittings: Brass Internal Parts Exposed to Gas: Monel Filter and Fusable Powdered Metal Panel Mounting Ring* Compression Fittings* (female connectors) 1 4" NPT female x 1 8" compression SG " NPT female x 1 4" compression SG6724 Acetylene Flash Arrestor* SG6545 * If selected, these items are not installed on the regulator. They are shipped as separate items. ADVANCED Specialty Gas 27

3 HIGH PURITY REGULATORS FOR GAS WITHDRAWAL FROM CRYOGENIC CONTAINERS (LC SERIES) The LC Series Regulators are specially designed for use on the gaseous withdrawal port of cryogenic liquid containers. These metal diaphragm, single-stage regulators are ideal for applications requiring both high flow and diffusion resistant pressure regulation. These LC Regulators have been specially designed to accept a maximum inlet pressure of 3000 psig, allowing them to be used on high pressure compressed gas cylinders as well. In addition to the high inlet pressure feature, new higher delivery pressure ranges of 350 psig and 500 psig are available for special laser cutting applications. Specially Designed for Gaseous Withdrawal from Cryogenic Liquid Containers. High Pressure Regulator Design accepts inlet pressures up to 3000 psig allowing it to be used on high pressure cylinders as well as liquid containers. High Flow Capacity capable of flow rates in excess of 1500 scfh. Stainless Steel Diaphragm minimizes diffusion of air into regulator and eliminates offgasing associated with elastomeric diaphragms, thus maintaining gas purity. Tamper proof, self-seating internal relief valve protects regulator from overpressurization. Filter in Seat Assembly traps foreign matter, extends regulator life and reduces maintenance. Diaphragm Seal Outlet Valve provides for flow shut-off while maintaining gas purity (Valve may reduce regulator flow capacity). Maximum Inlet Pressure: 3000 psig Pressure Range: See Table I Pressure Gauge: See Table I Gauge Size: 2 1 2" Dial Flow Coefficient: Cv = 0.36 Inlet Connection: CGA 320, 540 or 580 as ordered Outlet Connection: 1 4" NPT female Internal Relief Valve: Self Re-seating 600 psig Approximate Weight: 4 lbs Optional Diaphragm Valve: See Model SG5460N (Page 95) Body: Forged Brass Diaphragm: Type 316 Stainless Steel Gauge and Bonnet: Brass Brass and Stainless Steel Seat and Seals: Teflon Optional Diaphragm Valve: See Model SG5460N (Page 95) LC Regulator Pressure (psig) Range Gauge LC125-(CGA) LC350-(CGA) LC500-(CGA) Where (CGA) is indicated above, insert appropriate Compressed Gas Association connection number to complete the part number. Example: LC Order by complete part number. Diaphragm Seal Outlet Valve (installed) SG5460N-i 28 ADVANCED Specialty Gas

4 PRESET FLOW PISTON REGULATORS FOR NON-REFILLABLE CYLINDERS (MODEL SG9090) The Model SG9090 regulator is a compact, lightweight regulator recommended for use with non-corrosive standard calibration gases filled in transportable disposable cylinders having a maximum service pressure of 1000 psig. These single-stage regulators are designed to provide nominal (air equivalent) flow rates of 0.3, 0.5, 1, 1.5 or 2.5 slpm with a preset outlet pressure setting of 60 psig. Outlet Orifice and Preset Pressure provide a nominal preset gas flow rate. Pressure Gauge monitors cylinder pressure. Push Button On/Off Outlet Valve permits a quick and safe shutoff of gas flow. Maximum Inlet Pressure: 1000 psig Inlet Pressure Gauge: psig Nominal Preset Flowrate: See Table I Nominal Preset Pressure: 60 psig Gauge Size: 1 1 2" Dial -5 F to +140 F Inlet Connection: C-10 male (5 8" 18 UNF) Outlet Connection: 3 16" Hose Barb Approximate Weight: 1 lb. Body: Nickel-Plated Brass Gauge: Phosphor Bronze Piston: Brass Seat: PCTFE Seals: Viton SG9090 Regulator Nominal Flowrate (slpm) SG SG SG SG SG REGULATORS FOR SPECIFIC APPLICATIONS PRESET PRESSURE MINIATURE REGULATORS FOR NON-REFILLABLE LOW PRESSURE CYLINDERS (MODELS SG9094, SG9095) The Models SG9094 and SG9095 regulators are compact, lightweight, single-stage regulators designed for use with Automotive Test Standards in low pressure disposable cylinders. A 5 ft. length of polyethylene tubing, attached to the outlet, is included with each regulator. Both models are factory preset to provide 5 psig delivery pressure. The Model SG9095 is supplied with a psig inlet pressure gauge to monitor cylinder contents. Maximum Inlet Pressure: 300 psig Inlet Pressure Gauge: SG9094: None SG9095: psig Pressure Range: Factory preset to 5 psig Gauge Size: 1 1 2" Dial -40 F to +125 F Inlet Connection: CGA 165 Outlet Connection: 1 4" Flexible Tubing Approximate Weight: SG9094: 10 oz SG9095: 14 oz Body: Die Cast Zinc Gauge: SG9095: Brass Internals with drawn steel case Bonnet: Plastic Inlet Fitting: Brass Seat, Seals and Diaphragm: Buna-N Tubing: Polyethylene SG9094 SG9095 Configuration Without Inlet Pressure Gauge With Inlet Pressure Gauge SG9094 Regulator SG9095 Regulator ADVANCED Specialty Gas 29

5 TWO-STAGE REGULATORS FOR CLINICAL BLOOD GAS MIXTURES (AG3560 SERIES) This two-stage regulator provides the precise control needed for calibration of blood gas analyzers. Two-Stage Regulator Design ensures constant delivery pressure over varying inlet pressures. Available Yoke Connection (CGA 973) allows regulator to be used on small cylinders with post type valves. Metering Valve allows for precise, low flow gas control to blood gas analyzer. Chrome-Plated Surfaces provide polished appearance and ease of cleaning. Filter in each Seat Assembly traps foreign matter, extends regulator life and reduces maintenance. Maximum Inlet Pressure: 3000 psig Inlet Pressure Gauge: psig Pressure Range: 2 15 psig Pressure Gauge: 0 30 psig Gauge Size: 2" Dial -40 F to +140 F Inlet Connection: CGA 973 or 500 as ordered Outlet Connection: 1 8" Hosebarb (on outlet valve) Approximate Weight: 5 lbs Body, Gauges and Outlet Valve: Chrome-Plated Brass Bonnet: Chrome-Plated Die Cast Zinc Brass and Stainless Steel Seats and Seals: Teflon Diaphragms: Type 316L Stainless Steel Nylon Washers for CGA 973 (package of 25) AG3562 Series Regulator Inlet Connection AG3561 CGA 500 AG3562 CGA 973 SG6083 TWO-STAGE REGULATORS FOR MEDICAL GASES (AG3660 SERIES) AG3660 Series regulators are designed specifically for use with medical gases and medical gas mixtures. Two-Stage Regulator Design ensures constant delivery pressure over varying inlet pressures. Chrome-Plated Surfaces provide polished appearance and ease of cleaning. Filter in Each Seat Assembly traps foreign matter, extends regulator life and reduces maintenance. Available Yoke Connections allow regulator to be used on small cylinders with post type valves. Maximum Inlet Pressure: See Tables I and II Inlet Pressure Gauge: See Tables I and II Pressure Range: 4 50 psig Pressure Gauge: psig Gauge Size: 2" Dial Flow Capacity (typical): 100 Lpm at 45 psig delivery pressure with 250 psig inlet pressure Inlet and Outlet Connections: See Tables I and II Approximate Weight: 5 lbs AG3660 Regulator Body and Gauges: Chrome-Plated Brass Bonnet: Chrome-Plated Die Cast Zinc Brass and Stainless Steel Seats and Seals: Teflon Diaphragms: Type 316L Stainless Steel 30 ADVANCED Specialty Gas

6 , Pure Gases Inlet Outlet Connection Connection Inlet Pressure (psig) Service (CGA) (DISS)* Max. Gauge Air AG3660-(CGA) Carbon Dioxide AG3665-(CGA) Helium AG3660-(CGA) Nitrogen AG3662-(CGA) Nitrous Oxide AG3665-(CGA) Oxygen AG3660-(CGA) Where (CGA) is indicated above, insert proper Compressed Gas Association connection number to complete the part number. Example: AG is a regulator with a CGA 870 pin indexed connection (yoke) for Oxygen service. Order by complete part number. * Diameter Index Safety System (DISS) per Compressed Gas Association Pamphlet V-5. I, Mixtures Inlet Outlet Connection Connection Inlet Pressure (psig) Service (CGA) (DISS)* Max. Gauge REGULATORS FOR SPECIFIC APPLICATIONS Carbon Dioxide/Air AG3661-(CGA) " NPT female** Carbon Dioxide/Oxygen AG3660-(CGA) (CO 2 7.0%) 880 Carbon Dioxide/Oxygen AG3662-(CGA) (CO 2 > 7.0%) 940 Helium/Oxygen AG3661-(CGA) (He 80.0%) 890 Helium/Oxygen AG3660-(CGA) (He > 80.0%) 930 Nitrogen/Oxygen AG3662-(CGA) " NPT female** (O 2 > 23.5%) 890 Xenon/Oxygen AG3661-(CGA) (O 2 > 20%) 890 Carbon Dioxide/ AG3661-(CGA) " NPT female** Oxygen/Nitrogen 973 Helium/Oxygen/Nitrogen AG3661-(CGA) " NPT female** Where (CGA) is indicated above, insert proper Compressed Gas Association connection number to complete the part number. Example: AG is a regulator with a CGA 973 pin indexed connection (yoke) for Carbon Dioxide/Air mixtures. Order by complete part number. * Diameter Index Safety System (DISS) per Compressed Gas Association Pamphlet V-5. ** No outlet connection has been assigned under DISS per CGA Pamphlet V-5. ADVANCED Specialty Gas 31

7 SINGLE-STAGE, TIED SEAT REGULATORS FOR SILANE AND DICHLOROSILANE (SG3860 SERIES) These regulators are specifically designed to handle the unique properties of Silane and Dichlorosilane. Type 316 Stainless Steel Construction provides maximum corrosion resistance " Stainless Steel Gauges read easily for more precise settings. Tied Seat (tied diaphragm) reduces premature regulator failure caused by silicon dioxide build-up on seat created by reaction of silane with air. Unique Regulator Design permits regulator to be used with low vapor pressure gases such as Dichlorosilane. Diaphragm Seal Outlet Valve maintains gas purity. Rupture Disk Assembly (Model SG3862, SG3865 & SG3866 Only) prevents overpressurization of regulator and downstream system and allows for connection to a disposal system. Bonnet Vent Connector provides 1 8" NPT female port allowing bonnet to be connected to a vent line or disposal system as a precaution in the unlikely event of a diaphragm failure. Internal (Inboard) Helium Leak Test and Test Report determines inboard leak rate; test report certifies leak rate of less than 2 x 10 8 sccs air equivalent. External (Outboard) Helium Leak Test and Test Report determines leak rate of gas from regulator to atmosphere; test report certifies leak rate of less than 5 x 10 7 sccs air equivalent. Maximum Inlet Pressure: See Table I Inlet Pressure Gauge: See Table I Pressure Range: See Table I Pressure Gauge: See Table I Gauge Size: 2 1 2" Dial Flow Coefficient: Regulator: Cv = Outlet Valve: Cv = 0.26 Inlet Connection: Models SG3862, SG3865 & SG3866: CGA 350 for Silane & Silane Mixtures Model SG3860: CGA 678 for Dichlorosilane Outlet Connection: 1 4" NPT female (on outlet valve) Optional Rupture Disk Vent Connection: 1 4" NPT male Supply Pressure Effect: 1 psi per 100 psi (approximate) Approximate Weight: 7 lbs Body: Type 316 Stainless Steel Bar Stock Outlet Valve and Gauges: Type 316 Stainless Steel Bonnet: Nickel-Chrome Plated Brass Type 316 Stainless Steel Seats (Regulator and Outlet Valve): PCTFE Diaphragm: Type 316 Stainless Steel Seals: Teflon, Regulators SG3865 Regulator with Optional Rupture Disk Assembly Inlet Pressure (psig) Pressure (psig) Service Max. Gauge Range Gauge SG3862 Silane or Silane Mixtures * SG3865 Silane or Silane Mixtures SG3866 Silane or Silane Mixtures SG3860 Dichlorosilane * * This is a compound gauge with a range of 30" Hg vacuum to 0 to 30 psig. I, Optional Rupture Disk Assembly For Rupture Disk Rupture Pressure Replacement Rupture Regulator Assembly (psig) Disk SG3866 SG SG3865 SG SG3862 SG Inboard Helium Leak Test and Test Report HT1000 Outboard Helium Leak Test and Test Report HT1001 Bonnet Vent Connector** SG5647 Teflon Washers for CGA 678 (package of 25) SG6077 Purge Assemblies** (Cross purge assemblies are recommended) See page 42 ** If selected, these items are not installed on the regulator. They are shipped as separate items. 32 ADVANCED Specialty Gas

8 SINGLE-STAGE REGULATORS FOR HIGH DELIVERY PRESSURES (AG3840, AG3900 SERIES) These single-stage, piston sensed, pressure regulators are designed for applications requiring very high delivery pressures (up to 2500 psig). Constructed of either brass or stainless steel, they are available in both cylinder and line configurations. High Pressures up to 2500 psig. Piston Sensor Design ensures safe reliable service. Filter in Inlet traps foreign matter, extends regulator life and reduces maintenance. Diaphragm Seal Outlet Valve provides for on/off flow control (cylinder regulators only). Mounting Ring permits regulator to be panel mounted Captured Venting Configuration provides 1 16" NPTF vent port and stem packing allowing for complete capturing of bonnet when connected to a vent line or disposal system. Maximum Inlet Pressure: 3000 psig Inlet Pressure Gauge (dual scale): Cylinder Regulators: psig / bar Line Regulators: None Pressure Range: See Tables I & II Pressure Gauge: See Tables I & II Filter: 40 micron Gauge Size: 2" Dial -15 F to +140 F Flow Coefficient: Regulator: Cv = 0.06 Outlet Valve: Cv = 0.17 Inlet Connections: Cylinder Regulators: AG3840 Series: CGA 320, 326, 346, 350, 540, 580, or 590 as ordered AG3900 Series: CGA 290, 320, 326, 346, 350, 540, 580, or 590 as ordered Line Regulators: 1 4" NPT female Outlet Connection: 1 4" NPT female Approximate Weight: 3 lbs., AG3840 Series (Brass) AG3900 Regulator Body and Outlet Valve: AG3840 Series: Brass Bar Stock AG3900 Series: Type 316 SS Bar Stock Gauges: AG3840 Series: Brass AG3900 Series: Type 316 SS Bonnet: AG3840 Series: Brass Bar Stock AG3900 Series: 300 Series SS AG3840 Series: Brass and Stn. Stl. AG3900 Series: Type 316 Stn. Stl. Seat: Teflon Seals: Viton and Teflon Outlet Valve: Seat: PCTFE Diaphragm: Type 316 Stainless Steel Pressure Range Gauge (dual scale) Type (psig) (psig) (bar) AG3840-(CGA) Cylinder AG3841-(CGA) Cylinder AG3842-(CGA) Cylinder AG3843 Line AG3844 Line AG3845 Line REGULATORS FOR SPECIFIC APPLICATIONS Panel Mounting Ring* PM3803 Safety Mounting Brackets* See page 86 Captured Venting Configuration: AG3840 Series SG5651 AG3900 Series SG5650 * If selected, these items are not installed on the regulator. They are shipped as separate items. I, AG3900 Series (Stainless Steel) Pressure Range Gauge (dual scale) Type (psig) (psig) (bar) AG3900-(CGA) Cylinder AG3901-(CGA) Cylinder AG3902-(CGA) Cylinder AG3903 Line AG3904 Line AG3905 Line Where (CGA) is indicated above, insert appropriate Compressed Gas Association connection number to complete the part number. Example: AG or AG Order by complete part number. ADVANCED Specialty Gas 33

9 SINGLE-STAGE REGULATORS FOR HIGH INLET PRESSURES (AG3850, AG3910 SERIES) These single-stage, piston sensed, pressure regulators are designed for use with inlet pressures up to 5000 psig; such as required for use on 3500 psig (3K) and 4500 psig (HC-500) cylinders. Constructed of either brass or stainless steel, they are available in both cylinder and line configurations. High Pressures up to 2500 psig. Piston Sensor Design ensures safe reliable service. Filter in Inlet traps foreign matter, extends regulator life and reduces maintenance. Diaphragm Seal Outlet Valve provides for on/off flow control (cylinder regulators only). Mounting Ring permits regulator to be panel mounted Captured Venting Configuration provides 1 16" NPTF vent port and stem packing allowing for complete capturing of bonnet when connected to a vent line or disposal system. Bonnet: AG3850 Series: Brass Bar Stock AG3910 Series: 300 Series SS AG3850 Series: Brass and Stn. Stl. AG3910 Series: Type 316 Stn. Stl., AG3850 Series (Brass) Seat: Teflon Seals: Viton and Teflon Outlet Valve: Seat: PCTFE Diaphragm: Type 316 Stn. Stl. AG3850 Regulator Pressure Range Gauge (dual scale) Type (psig) (psig) (bar) AG3850-(CGA) Cylinder AG3851-(CGA) Cylinder AG3852-(CGA) Cylinder AG3853 Line AG3854 Line AG3855 Line Maximum Inlet Pressure: 5000 psig Inlet Pressure Gauge: Cylinder Regulators: psig Line Regulators: None Pressure Range: See Tables I & II Pressure Gauge: See Tables I & II Filter: 40 micron Gauge Size: 2" Dial Operating Temp. Range: -15 F to +140 F Flow Coefficient: Regulator: Cv = 0.06 Outlet Valve: Cv = 0.17 Inlet Connections: Cylinder Regulators: CGA 347, 350, 580, 680 or 685 as ordered Line Regulators: 1 4" NPT female Outlet Connection: 1 4" NPT female Approximate Weight: 3 lbs. Body and Outlet Valve: AG3850 Series: Brass Bar Stock AG3910 Series: Type 316 SS Bar Stock Gauges: AG3850 Series: Brass AG3910 Series: Type 316 SS I, AG3910 Series (Stainless Steel) Pressure Range Gauge (dual scale) Type (psig) (psig) (bar) AG3910-(CGA) Cylinder AG3911-(CGA) Cylinder AG3912-(CGA) Cylinder AG3913 Line AG3914 Line AG3915 Line Where (CGA) is indicated above, insert appropriate Compressed Gas Association connection number to complete the part number. Example: AG or AG Order by complete part number. Panel Mounting Ring* Captured Venting Configuration: AG3850 Series AG3910 Series * If selected, these items are not installed on the regulator. They are shipped as separate items. PM3803 SG5651 SG ADVANCED Specialty Gas

10 SINGLE-STAGE REGULATORS FOR VERY HIGH INLET PRESSURES (SG3600 SERIES) These piston-type regulators are designed for use on 6000 psig (6K) cylinders. The stainless steel models are designed for applications requiring inlet pressures up to 10,000 psig. Both brass and stainless models are available as line regulators. WARNING: Self-relieving regulators should not be used in a confined area or with flammable gases. Injury or death may result. Large Low-Torque Handle allows easy adjustment of delivery pressure. Filter in Inlet traps foreign matter, extends regulator life and reduces maintenance. Outlet Metering Valve provides flow control (cylinder regulators only). Self-Relieving Models automatically vent downstream pressure should it exceed delivery pressure setting and permits operator to reduce pressure setting by venting downstream pressure through hand-knob. Mounting Ring permits regulator to be panel mounted. Body and Gauges: See Tables Outlet Valve: Type 316 Stainless Steel Bonnet: Brass Regulators: Brass Stainless Steel Regulators: Electroless Nickel-Plated Brass Brass Regulators: Brass and Stn. Stl. Stainless Steel Regulators: Type 303 and Type 316 Stn. Stl Seat: PCTFE Seals: Regulator: Viton Outlet Valve: Teflon, Non-Relieving Cylinder Regulators SG3610 Cylinder Regulator SG3611 Line Regulator REGULATORS FOR SPECIFIC APPLICATIONS Maximum Inlet Pressure: See Tables Inlet Pressure Gauge: See Tables Pressure Range: See Tables Pressure Gauge: See Tables Gauge Size: 21 2" Dial Operating Temp. Range: -65 F to +140 F Flow Coefficient: Regulator: Cv = 0.06 Outlet Valve: Cv = 0.45 Inlet Connection: Self-Relieving Cylinder Regulators: CGA 347, 677, 680 or 702 as ordered Non-Relieving Cylinder Regulators: CGA 347, 677, 680, 695, 701, 702 or 703 as ordered Line Regulators: 1 4" NPT female Outlet Connection: Cylinder Regulators: 1 4" NPT male (on outlet valve) Line Regulators: 1 4" NPT female Supply Pressure Effect: 1.0 psi per 100 psi Approximate Weight: 6 lbs Inlet Body Gauge Pressure (psig) Pressure (psig) Material Material Max. Gauge Range Gauge SG3610-(CGA) Brass Brass SG3612-(CGA) Brass Brass SG3614-(CGA) Brass Brass SG3620-(CGA) Type 303 SS Type 316 SS 10, , SG3622-(CGA) Type 303 SS Type 316 SS 10, , I, Self-Relieving Cylinder Regulators Inlet Body Gauge Pressure (psig) Pressure (psig) Material Material Max. Gauge Range Gauge SG3600-(CGA) Brass Brass SG3602-(CGA) Brass Brass SG3604-(CGA) Brass Brass Where (CGA) is indicated in Tables I and II, insert appropriate Compressed Gas Association connection number to complete the part number. For example: SG Order by complete part number. Panel Mounting Ring Oxygen Cleaning for inlet pressures above 3000 psig (required for CGA 701) PM3804 OC100 II, Line Regulators Inlet Body Gauge Pressure (psig) Pressure (psig) Material Material Max. Gauge Range Gauge SG3611 Brass Brass 6000 None SG3613 Brass Brass 6000 None SG3621 Type 303 SS Type 316 SS 10,000 None SG3623 Type 303 SS Type 316 SS 10,000 None ADVANCED Specialty Gas 35

11 TWO-STAGE CYLINDER REGULATORS FOR VERY LOW DELIVERY PRESSURES (MODEL TSC) The Model TSC Regulator provides highly accurate pressure reduction of inlet pressures up to 3000 psig down to delivery pressures as low as 0.3 to 3 psig. The two-stage design provides constant outlet pressure regardless of changes in cylinder (inlet) pressures. The Model TSC is suitable for use with noncorrosive gases where high purity is not required. Typical applications include low pressure purging, inert blanketing of chemical or flammable storage units, or control of fuel to burners. Large 3" Diaphragm in second stage, allows for accurate control of delivery pressures down to 0.3 psig. Two-Stage Regulator Design ensures constant delivery pressure over varying inlet pressures. Sintered Metal Filters (in inlet port and between stages) trap foreign matter, extend regulator life, and reduce maintenance. Pressure Relief Valve protects regulator from overpressurization. 1-Ounce Graduations on a 21 2" Outlet Gauge allow for enhanced readability at very low pressure settings. Outlet Metering Valve provides flow control. Body and Outlet Valve: Forged Brass Gauges: Brass Internals with Drawn Steel Case Bonnet: First Stage: Forged Brass Second Stage: Chrome-Plated Zinc Brass and Stainless Steel Seats: First Stage: PCTFE Second Stage: Viton Diaphragms: Viton Seals: Regulator: Viton Outlet Valve: Teflon TSC Regulator Maximum Inlet Pressure: 3000 psig Inlet Pressure Gauge: psig Pressure Range: psig Pressure Gauge: 0 5 psig Gauge Size: 2 1 2" Dial -20 F to +140 F Flow Coefficient: Regulator: Cv = 0.2 Outlet Valve: Cv = 0.35 Relief Valve Setting (interstage): psig Inlet Connection: CGA 296, 346, 350, 510, 540, 580, 590, 660 as ordered. Outlet Connection: 1 4" NPT male (on outlet valve) Maximum Flow Rate: 98 scfh N 2 at 2000 psig inlet pressure. Approximate Weight: 7 lbs TSC-(CGA) Where (CGA) is indicated above, insert appropriate Compressed Gas Association connection number to complete the part number. Example: TSC-580. Order by complete part number. Compression Fittings* (female connectors) 1 4" NPT female x 1 8" compression SG " NPT female x 1 4" compression SG6724 Check Valves* See page 99 * If selected, these items are not installed on the regulator. They are shipped as separate items. 36 ADVANCED Specialty Gas

12 SINGLE-STAGE, LOW INTERNAL VOLUME REGULATORS FOR REACTIVE GAS MIXTURES (MODEL SG9200) This metal diaphragm, single-stage stainless steel regulator features a scant internal volume of just 3.0 cubic centimeters. This low internal volume and special cleaning process provides for ease of purging and reduces contamination potential. The Model SG9200 regulator is ideal for EPA Protocol, low level VOC analyses, and Ultra High Purity applications. Low Internal Volume of only 3.0 cubic centimeters allows rapid purging in analytical instrumentation applications. Stainless Steel Diaphragm minimizes diffusion of air into regulator and eliminates off gassing associated with elastomeric diaphragms, thus maintaining gas purity. High Purity Regulator Design permits vacuum purging of regulator. Special Cleaning Process eliminates organic film and any surface adhering particles to ensure a stable base line in low level VOC analyses and Ultra High Purity Applications. Maximum Inlet Pressure: 3000 psig Inlet Pressure Gauge: psig Pressure Range: See Table I Pressure Gauge: See Table I -40 F to +140 F Flow Coefficient: Cv = 0.06 Inlet Connection: CGA 320, 330, 350, 510, 580, 590 or 660 as ordered. Outlet Connection: 1 8" compression fitting Approximate Weight: 2.5 lbs Body and Gauges: Type 316 Stainless Steel Bonnet: Anodized Black Aluminum Type 316 Stainless Steel Seat: PCTFE Diaphragm: Type 316 Stainless Steel Seals: Teflon SG9200 Regulator REGULATORS FOR SPECIFIC APPLICATIONS Pressure (psig) Range Gauge SG9201-CGA SG9200-CGA Where (CGA) is indicated above, insert appropriate Compressed Gas Association connection number to complete the part number. Example: SG Order by complete part number. ADVANCED Specialty Gas 37

13 SINGLE-STAGE, HIGH FLOW REGULATORS FOR HIGH PURITY GASES (MODELS UPH, UPHS) These metal diaphragm, single-stage regulators are specially designed for applications requiring both high flow and diffusion resistance. The Model UPH is for noncorrosive gases; Model UPHS is suitable for use with corrosive gases. High Flow Capacity capable of flow rates in excess of 60 scfm of air. Stainless Steel Diaphragm minimizes diffusion of air into regulator and eliminates off gassing associated with elastomeric diaphragms, thus maintaining gas purity. High Purity Regulator Design permits vacuum purging of regulator. Balanced Poppet (stem) minimizes effect of changes in inlet pressure on delivery pressure settings. Threaded Holes in Rear of Regulator permit front panel mounting. Bonnet Vent Connector provides 1 8" NPT female port allowing bonnet to be connected to a vent line or disposal system as a precaution in the unlikely event of a diaphragm failure. Internal (Inboard) Helium Leak Test and Test Report determines inboard leak rate; test report certifies leak rate of less than 2 x 10 8 sccs air equivalent. External (Outboard) Helium Leak Test and Test Report determines leak rate of gas from regulator to atmosphere; test report certifies leak rate of less than 5 x 10 7 sccs air equivalent. Maximum Inlet Pressure: See Table I Inlet Pressure Gauge: See Table I Pressure Range: See Table I Pressure Gauge: See Table I Gauge Size: 2 1 2" Dial -40 F to +140 F Flow Coefficient: Cv = 0.6 Inlet Connection: Model UPH: CGA 296, 320, 326, 346, 350, 510, 540, 580, 590, or 660 as ordered Model UPHS: CGA 290, 320, 326, 330, 346, 350, 510, 580, 590, 660 or 705 as ordered Outlet Connection: 1 4" NPT female Supply Pressure Effect: <1.0 psi per 100 psi Approximate Weight: 5 lbs Body: Model UPH: Brass Bar Stock Model UPHS: Type 316 SS Bar Stock Gauges: Model UPH: Brass Model UPHS: Type 316 Stainless Steel Bonnet: Electroless Nickel-Plated Brass Type 316 Stainless Steel Seat: PCTFE Diaphragm: Type 316L Stainless Steel Seals: Teflon UPH Regulator Inlet Pressure (psig) Pressure (psig) Brass Regulators Stn. Stl. Regulators Max. Gauge Range Gauge UPH-3-30-(CGA) UPHS-3-30-(CGA) UPH-3-75-(CGA) UPHS-3-75-(CGA) UPH (CGA) UPHS (CGA) UPH (CGA) UPHS (CGA) UPH-2-30-(CGA) UPHS-2-30-(CGA) UPH-2-75-(CGA) UPHS-2-75-(CGA) UPH (CGA) UPHS (CGA) UPH (CGA) UPHS (CGA) UPH-1-30-(CGA) UPHS-1-30-(CGA) UPH-1-75-(CGA) UPHS-1-75-(CGA) UPH (CGA) UPHS (CGA) UPH (CGA) UPHS (CGA) Where (CGA) is indicated above, insert appropriate Compressed Gas Association connection number to complete the part number. Example: UPH Order by complete part number. Inboard Helium Leak Test and Test Report HT1000 Outboard Helium Leak Test and Test Report HT1001 Panel Mounting Ring* PM3803 Bonnet Vent Connector* Model UPH SG5645 Model UPHS SG5647 Check Valves* See page 99 * If selected, these items are not installed on the regulator. They are shipped as separate items. Bonnet Vent Connector is not required for UPH-X-250 and UPHS-X-250 Models. 38 ADVANCED Specialty Gas

14 SINGLE-STAGE, VERY HIGH FLOW REGULATORS (MODELS SG3882, SG3883) This piston-type regulator is designed for use when very high flow rates are required. Typical uses include manifold or trailer applications. Model SG3882 is suitable for noncorrosive service, while Model SG3883 is designed for corrosive gases that are compatible with the materials of construction. WARNING: The Model SG3883 Regulator is not recommended for oxygen service. High Flow Capacity allows flows in excess of 500 scfm of air at 3000 psig inlet. Balanced Poppet (stem) minimizes effect of changes in inlet pressure on delivery pressure settings. Pressure Relief Valve protects regulator components from the effects of overpressurization. Stainless Steel Filter in Inlet traps foreign matter, extends regulator life and reduces maintenance. Large Low-Torque Handle allows easy adjustment of delivery pressure. Mounting Ring permits regulator to be panel mounted. Maximum Inlet Pressure: 3750 psig Inlet Pressure Gauge: psig Pressure Range: See Tables I & II Pressure Gauge: See Tables I & II Relief Valve: Self-Reseating, 1 4" NPT Outlet Gauge Size: 2 1 2" Dial 0 F to +165 F Flow Coefficient: Cv = 1.7 Inlet and Outlet Connections: 1 2" NPT female Supply Pressure Effect: 1.0 psi per 100 psi Approximate Weight: 7 lbs Body: Model SG3882: Brass Bar Stock Model SG3883: Type 303 SS Bar Stock Bonnet: Model: SG3882: Brass Model: SG3883: 300 Series Stn. Stl. Gauges: Model: SG3882: Brass Model: SG3883: Type 316 Stn. Stl Model SG3882: Brass and Stn. Stl Model SG3883: 300 Series Stn. Stl Seats: Teflon Seals: Viton and PCTFE Filter: Type 303 Stn. Stl SG3882 Regulator REGULATORS FOR SPECIAL APPLICATIONS, Brass Pressure (psig) Range Gauge SG SG Panel Mounting Ring PM3804 I, Stainless Steel Pressure (psig) Range Gauge SG SG ADVANCED Specialty Gas 39

15 ADJUSTABLE BACK PRESSURE REGULATORS FOR HIGH PURITY GASES (MODELS ABPB, ABPS) These metal diaphragm, high purity back pressure regulators are specially designed to control inlet pressure. Unlike pressure reducing regulators, these devices control inlet pressure rather than outlet or downstream pressure. They operate like highly sensitive, adjustable relief valves. The inlet (system) pressure is controlled by relieving pressure through the regulator from the system to maintain pressure at or below a desired level. Back pressure regulators are commonly used to prevent overpressurization of storage vessels, fluid sampling systems, compressor and pumping systems. Model BPB is manufactured from brass bar stock and is designed for noncorrosive gases; Model BPS, which is constructed from Type 316L SS bar stock, is suitable for use with corrosive gases. Convoluted 316 SS diaphragm provides excellent accuracy, high sensitivity, and close tolerances on crack-reseat pressure relationships. High Purity Regulator Design permits vacuum purging of regulator. Threaded Holes in Rear of Regulator permit front panel mounting. Captured Venting Configuration provides 1 16" NPTF vent port and stem packing allowing for complete capturing of bonnet when connected to a vent line or disposal system. Mounting Ring permits regulator to be panel mounted. Internal (Inboard) Helium Leak Test and Test Report determines inboard leak rate; test report certifies leak rate of less than 2x10 8 sccs air equivalent. External (Outboard) Helium Leak Test and Test Report determines leak rate of gas from regulator to atmosphere; test report certifies leak rate of less than 5x10 7 sccs air equivalent. Maximum Rated Pressure: 250 psig Relief Pressure Range: See Table I -40 F to +165 F Flow Coefficient: Cv = 0.08 Inlet and Outlet Connections: 1 4" NPT female H.P. Plugged Access Port: 1 4" NPTF Approximate Weight: 2 lbs Body: Model ABPB: Brass Bar Stock Model ABPS: Type 316L SS Bar Stock Bonnet: Model ABPB: Brass Model ABPS: 300 Series Stainless Steel Model ABPB: Brass and Stainless Steel Model ABPS: Type 316 Stainless Steel Seat: PCTFE Diaphragm: Type 316 Stainless Steel Relief Pressure Brass Regulators Stainless Steel Regulators Range (psig) ABPB-30 ABPS ABPB-50 ABPS ABPB-100 ABPS ABPB-250 ABPS Panel Mounting Ring* Inboard Helium Leak Test and Test Report Outboard Helium Leak Test and Test Report Captured Venting Configuration Models ABPB Models ABPS * If selected, these items are not installed on the regulator. They are shipped as separate items. ABPS Regulator PM3803 HT1000 HT1001 SG5651 SG ADVANCED Specialty Gas