Tank-Mounted Suction Filter

Transcription

1 Tank- Suction 20 gpm 75 L/min 6.25 MAX. (159) OPTIONAL DI ALARM OR ELECTRIC SWITCH 4.06 MAX. (103) 1.88 (48).12 (3) THICK GASKET 5.06 (129) Ø HOLE TANK FOR ALLATION 6.38 PO TO PO (162) 45 TYP.44 (11) Ø ON A 6.25 (159) Ø B.C. (4) MOUNTG HOLES 1K = 8.81 (224) 2K = (457) 4.50 (114) Ø 7.00 Ø (178) 2.59 (66).88 (22) OPTIONAL CHECK VALVE Optional mounting ring available to weld to tank. Metric dimensions in ( ). Model No. of filter in photograph is 1K10SY. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Cap: Case: Weight of -1K: Weight of -2K: Change Clearance: Up to 20 gpm (75 L/min) f 150 SUS (32 cst) fluids Suction Not Applicable Not Applicable -20 F to 225 F (-29 C to 107 C) Non-bypassing Die Cast Aluminum Steel Steel 11.1 lbs. (5.0 kg) 14.7 lbs. (6.7 kg) 7.25 (185 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm K N/A N/A 44 KTZ Collapse Rating: 150 psid (10 bar) Flow Direction: Inside Out Nominal Dimensions: 4.0 (100 mm) O.D. x 9.0 (230 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z10 Z10 Z10 KZ10H, K10H KZ10H.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

2 Tank- Suction F hydrostatic suction service. Optional check valve prevents reservoir siphoning. Saves space, reduces plumbing. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid. Hydrostatic Suction Service Dirt Alarm No. of Seal Outlet Optional (See Appendix A f Series s Part No. Material Pting Check Valve complete list of options) E Media 1 2 G501 = Rubber gasket K10 1K10 2K10 K25 1K25 2K25 Z Media KTZ10 1KTZ10 2KTZ10 Flow gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element Note: Plotted curves shown in graph below include both housing and elements as indicated f fluids with sp gr = sp gr = specific gravity K10 K25** KTZ10 P psi (Omit) = Buna N H = EPR* W = Buna N* Flow (L/min) (25) (50) (75) -1K10-P-C -2K10-P-C P= NPTF -1K25-P-C PP = Dual NPTF S= SAE Straight (SAE-24) SS = Dual SAE Straight (SAE-24) B = ISO 228 G ( BSPP) BB = Dual ISO 228 G ( BSPP) -2K25-P-C Flow gpm Sizing of elements should be based on element flow infmation provided in the chart above. **When H W seals are dered, all aluminum parts are anodized. **Not available with EPR seals. G547 = Two 1 8 gauge pts See also Accessies f Tank- s section. (0.15) (0.10) (0.05) P (bar) (Omit) = None C = Check Valve Y = Vacuum Gauge YR = Vacuum Gauge on Opposite Side of Standard Location VS = Electric Vacuum Switch VS1 = Heavy-Duty Vacuum Switch See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 99

3 In-Line Magnetic Suction Separats In addition to offering our magnetic suction strainer (SKB) as a stand alone product, we also offer the SKB enclosed in a housing, so that it can be used either in-line (TF-SKB -SKB) as a reservoir-mounted filter (K-SKB -SKB). Flow rates and available pting vary refer to the specifications f each. TF-SKB Specifications Flow Rating: Replacement Part Number: Change Clearance: Weight of TF-SKB: 12.5 gpm (47 L/min) SKB (65 mm) 5.8 lbs (2.6 kg) Model Number Seal Dirt Alarm Series Material Pting (See Appendix A) Y = Vacuum Gauge TF-SKB Omit = Buna N P = 1 NPTF VS = Vacuum Electric Switch VS1 = Heavy Duty Vacuum Electric Switch -SKB Specifications Flow Rating: Replacement Part Number: Change Clearance: Weight of -SKB: 35 gpm (130 L/min) A-LF (40 mm) 11.5 lbs (5.2 kg) Model Number Seal Dirt Alarm Series Material Pting (See Appendix A) Y = Vacuum Gauge -SKB Omit = Buna N P = NPTF VS = Vacuum Electric Switch VS1 = Heavy Duty Vacuum Electric Switch 100

4 Tank- Magnetic Suction Separats Specifications Flow Rating: Replacement Part Number: Change Clearance: Weight of K-SKB: Model Number Seal Series Material Pting 35 gpm (130 L/min) P24P24 = NPT K-SKB Omit = Buna N P24P24 = Dual NPT Specifications Flow Rating: Replacement Part Number: Change Clearance: Weight of -SKB: Model Number with check valve: A-SKB-11P-1 with check valve f filter built befe Sept. 95: A-SKB-131 without check valve: A-SKB-99 without check valve f filter built befe Sept. 95: A-SKB (230 mm) 11.5 lbs (5.2 kg) 75 gpm (285 L/min) Seal Series Material Pting PP =2 1 2 NPTF -SKB PP = Dual NPTF Omit = FF = SAE J518 4-Bolt Buna N Flange Code 61 FF = Dual SAE J518 4-Bolt Flange Code 61 Dirt Alarm (See Appendix A) with check valve: A-SKB-3-76 without check valve: SKB (345 mm) 32.0 lbs (14.5 kg) Y = Vacuum Gauge YR = Y mounted on opposite side VS = Vacuum Electric Switch VSR = VS mounted on opposite side VS1 = Heavy Duty Vacuum Electric Switch Dirt Alarm (See Appendix A) Y = Vacuum Gauge YR = Y mounted on opposite side VS = Vacuum Electric Switch VSR = VS mounted on opposite side VS1 = Heavy Duty Vacuum Electric Switch Other Options C = Check Valve 1.78 (45) Other Options C = Check Valve K-SKB -SKB SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 101

5 MiniMiser Tank- 15 gpm 55 L/min 100 psi 7 bar.28 (7) Ø ON A 3.50 (89) Ø B.C. (2) MOUNTG HOLES 3.30 (109) Ø 2.00 (51) MAX (56) O-RG 1.84 (47) CAP SPRG OPTIONAL DI ALARM OR ELECTRIC SWITCH OPTIONAL MAGNET O-RG.89 (23) 5.06 (129) ELEMENT BYPASS VALVE 2.69 (68) Ø HOLE TANK REQ'D FOR ALLATION 3.22 (82) O-RG 2.37 Ø (60) BOWL Metric dimensions in ( ). Model No. of filter in photograph is 3TAZ10P8..94 Ø (24) Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head & Cap: Case: Weight of -3: Change Clearance: Up to 15 gpm (55 L/min) f 150 SUS (32 cst) fluids 100 psi (7 bar) 269 psi (18 bar) Contact facty -20 F to 225 F (-29 C to 107 C) Cracking: 25 psi (2 bar) Full Flow: 48 psi (3.3 bar) Die Cast Aluminum Glass Filled Nylon 1.0 lbs. (0.5 kg) 3.0 (76 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 3TA N/A N/A N/A 3TAZ3 <1.0 <1.0 < TAZ TAZ TAZ Collapse Rating: Flow Direction: Nominal Dimensions: 150 psid (10 bar) Outside In 2.0 (51 mm) O.D. x 3.0 (76 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

6 MiniMiser Tank- Cost effective alternative to spin-on filters. Compact size minimizes space requirements. Special filter design provides aftermarket benefits. selections are predicated on the use of 150 SUS (32 cst) petroleum based fluid and a 25 psi (1.7 bar) bypass valve. 10 3TA10 See E 25 3TA25 Z3 3TAZ3 See Z5 3TAZ5 See Z Z10 3TAZ10 See Z25 3TAZ25 See Pressure Series Part No. Return Line -Tank- Flow gpm (L/min) 0 (25) (50) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 7 gpm (27 L/min) f 3TAZ10P8 using 150 SUS (32 cst) fluid. Solution: P housing = 2.0 psi [.14 bar] P element = 7 x 1.48 = 10.3 psi P element = [27 x ( ) =.73 bar] P total = = 12.3 psi P element = [ =.87 bar] 3" TA10 TA25 TAZ3 TAZ5 TAZ10 TAZ25 G547 = Two 1 8 gauge pts P housing f fluids with sp gr = 0.86: P psi (Omit) = None M = Magnet Flow (L/min) (25) (50) Flow gpm sp gr = specific gravity P8 = 1 2 NPTF S8= SAE Straight (SAE-8) B8= IS) 228 G- 1 2 ( BSPP) P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 3TA 3TA TA TAZ TAZ TAZ TAZ TAZ25.68 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. Part No. Dirt Alarm Optional (See Appendix A f Series Length Media Magnet Pting Options complete list of options) (0.75) (0.5) (0.25) P (bar) Y2C = Bottom Gauge in Cap Y5 = Back Gauge in Cap ESC = Electrical Pressure Switch (2 Terminals) See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 103

7 MiniMiser Tank- 35 gpm 135 L/min 100 psi 7 bar 4.28 (109) Ø.38 (10) Ø ON A 4.50 (114) Ø B.C. (2) MOUNTG HOLES 2.79 (71) 60 CAP 2.19 MAX (56) SPRG 2.53 (64) O-RG OPTIONAL DI ALARM OR ELECTRIC SWITCH OPTIONAL MAGNET O-RG 1.11 (28) 3TB = 5.86 (1 49) 5TB = 8.17 (207) ELEMENT BYPASS VALVE 3.56 (90) Ø HOLE TANK REQ'D FOR ALLATION 3TB = 3.33 (85) 5TB = 5.64 (143) O-RG 3.14 Ø (80) BOWL Metric dimensions in ( ). Model No. of filter in photograph is 5TBZ5P Ø (27) Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head & Cap: Case: Weight of -3: Weight of -5: Change Clearance: Up to 25 gpm (95 L/min) f 150 SUS (32 cst) fluids -3 Up to 35 gpm (135 L/min) f 150 SUS (32 cst) fluids psi (7 bar) 229 psi (15 bar) Contact facty -20 F to 225 F (-29 C to 107 C) Cracking: 25 psi (2 bar) Full Flow: 51 psi (3.5 bar) Die Cast Aluminum Glass Filled Nylon 1.8 lbs. (0.8 kg) 2.1 lbs. (1.0 kg) 3.0 (76 mm) (127 mm) -5 Perfmance Fluid Compatibility Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 3TB N/A N/A N/A 3TBZ3 <1.0 <1.0 < TBZ TBSZ TBSZ TB N/A N/A N/A 5TBZ3 <1.0 <1.0 < TBZ TBZ TBZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 3TB: 3.0 (76 mm) O.D. x 3.0 (76 mm) long 5TB: 3.0 (76 mm) O.D. x 5.0 (127 mm) long Type Fluid Petroleum Based Fluids Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

8 MiniMiser Tank- Cost effective alternative to spin-on filters. Compact size minimizes space requirements. Special filter design provides aftermarket benefits. Pressure Series Part No. Return Line -Tank- Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 25 gpm (95 L/min) f 5TB25S16CY2 using 200 SUS (44 cst) fluid. Solution: P housing = 3.0 psi [.21 bar] P element = 25 x.08 x ( ) = 2.6 psi P element = [95 x ( ) x (44 32) =.19 bar] P total E Z Flow = = 5.6 psi P element = [ =.40 bar] 3" 5" TB10 TB25 TBZ3 TBZ5 TBZ10 TBZ25 G547 = Two 1 8 gauge pts selections are predicated on the use of 150 SUS (32 cst) petroleum based fluid and a 25 psi (1.7 bar) bypass valve. 10 See 3TB 5TB 25 See 3TB 5TB Z3 See 3TBZ3 5TBZ3 Z5 See 3TBZ5 5TBZ5 Z10 See 3TBZ10 5TBZ10 Z25 See 3TBZ25 5TBZ25 gpm (L/min) 0 (25) (50) (75) (100) (135) P housings f fluids with sp gr = 0.86: P psi Flow gpm sp gr = specific gravity (Omit) = None M = Magnet Flow (L/min) (25) (75) (125) -3 Housing -5 Housing P12 = 3 4 NPTF P16 = 1 NPTF S12 = "-12 SAE Straight (SAE-12) S16 = "-12 SAE Straight (SAE-16) B12 = ISO 228 G- 3 4 ( BSPP) B16 = ISO 228 G-1 (1-11 BSPP) P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 3" 5" TB TB TBZ TBZ TBZ TBZ TBZ If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. Part No. Dirt Alarm Optional (See Appendix A f Series Length Media Magnet Pting Options complete list of options) (0.75) (0.5) (0.25) P (bar) Y2C = Bottom Gauge in Cap Y5 = Back Gauge in Cap ESC = Electrical Pressure Switch (2 Terminals) See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 105

9 20 gpm 75 L/min 85 psi 6 bar Tank- with Integral Air Breather (108) (88) A.43 (11) Ø (2) MOUNTG HOLES (65) (59) 3.00 (76) A DISPOSABLE AIR BREATHER P = SCFM -4G = 5.91 (150) -8G = 9.72 (247) -4G = 3.35 (85) 2.56 (65) -8G = 7.16 (182).86 (22) -4G =.69 (18) Ø -8G =.81 (21) Ø 2.00 Ø (51) 3.00 Ø (76) COLOR CODED DI ALARM GAUGE O-RG SEAL 2.36 (60) Ø HOLE RESERVOIR OIL SEPARATOR Metric dimensions in ( ). Model No. of filter in photograph is 8G10Y6A. LET FITTG PROVIDES CAPABILITY TO ALL EXTENSION TUBE VIEW A-A Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head & Cap: Case: Weight of -4G: Weight of -8G: Change Clearance: Up to 20 gpm (75 L/min) f 150 SUS (32 cst) fluids 85 psi (6 bar) Contact facty Contact facty -20 F to 180 F (-29 C to 82 C) Cracking: 35 psi (2 bar) Glass Fiber Reinfced Plastic Glass Fiber Reinfced Plastic 0.8 lbs. (0.4 kg) 1.1 lbs. (0.5 kg) 4.75 (125 mm) 8.75 (225 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Dirt Holding ß x 75 ß x 100 ß x 200 Capacity gm 4G G GZ GZ GZ Flow Direction: Outside In Nominal Dimensions: 1.75 (45 mm) O.D. x 4.0 (105 mm) long 2.5 (65 mm) O.D. x 8.0 (200 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z10, Z25 Z10, Z25 Z10, Z25 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

10 Tank- with Integral Air Breather Constructed of glass fiber reinfced plastic. Built-in disposable air breather. Cost saving hose barb connection. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 35 psi bypass valve. Return E (Cellulose) 4G10 & 8G10 4G10 8G10 Line -Tank- Z 4GZ10 & 8GZ10 4GZ10 8GZ10 (Glass) 8GZ20 8GZ20 Dirt Alarm Part No. Seal (See Appendix f Series Length Media Material Pting complete list of options) Other Flow gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 10 gpm (38 L/min) f 8G10 using 200 SUS (44 cst) fluid. Solution: P housing = 1.5 psi [.12 bar] P element = 10 x.18 x ( ) = 2.4 psi P element = [38 x ( ) x (44 32) =.17 bar] P total = = 3.9 psi P element = [ =.29 bar] G10 GZ10 G10 GZ10 GZ25 P housing f fluids with sp gr = 0.86: (Omit) = Buna N Omit = Inlet: Male hose barb connection Outlet: Non-threaded connection I.D. P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 4G GZ G GZ GZ20.25 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. None 4 8 P psi sp gr = specific gravity Flow (L/min) (25) (50) (75) Flow gpm (0.50) (0.25) P (bar) Y6 = Col Coded Gauge ES6 = Electric Switch A = Dipstick See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 107

11 Tank- 40 gpm 150 L/min 100 psi 7 bar.56 (14) 5.88 MAX. (149).35 (9) Ø ON A 5.25 (133) Ø B.C. (3) MOUNTG HOLES 5.25 (133) 2.62 (67) 30 TYP. OPTIONAL DI ALARM LOCATED CAP OPTIONAL LET PO 3.12 (79) 1.38 (35) 8Z = 7.62 (194) 3.62 (92) Ø HOLE RESERVOIR 3.50 (89) Ø OPTIONAL DI ALARM OR ELECTRIC SWITCH Optional mounting ring available to weld to tank. Metric dimensions in ( ). Model No. of filter in photograph is 8ZZ10PY2. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head & Cap: Case: Weight of -8Z: Change Clearance: Up to 40 gpm (150 L/min) f 150 SUS (32 cst) fluids 100 psi (7 bar) 400 psi (28 bar) 90 psi (6 bar), per NFPA T2.6.1-R F to 225 F (-29 C to 107 C) Cracking: 25 psi (1.7 bar) Full Flow: 39 psi (2.7 bar) Die Cast Aluminum Steel 3.7 lbs. (1.7 kg) 10.0 (254 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 8Z N/A N/A 39 8Z N/A N/A 32 8Z1 <1.0 <1.0 <1.0 < Z3 <1.0 <1.0 < Z Z Z Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 3.0 (75 mm) O.D. x 9.25 (235 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5 and Z25H.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

12 Tank- Dual inlet pting available. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 25 psi (1.7 bar) bypass valve. Return Line -Tank- E Media Z Media Flow 8 8Z3 paper 8Z10 paper 8Z25 paper 8ZZ3 8ZZ5 8ZZ10 8ZZ25 Z3** Z10** Z25** ZZ1 ZZ3 ZZ5 ZZ10 ZZ25 (Omit) = Buna N H = EPR* P = 1 NPTF PP = Dual 1 NPTF S= SAE Straight (SAE-16) SS = Dual SAE Straight (SAE-16) B = ISO 228 G-1 (1-11 BSPP) BB= Dual ISO 228 G-1 (1-11 BSPP) 8Z3 (cellulose media) 8Z10 (cellulose media) 8Z25 (cellulose media) 8ZZ3 8ZZ5 8ZZ10 8ZZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 20 gpm (76 L/min) f 8ZZ1PES using 200 SUS (44 cst) fluid. Solution: P housing = 1 psi [.07 bar] P element = 20 x.37 x ( ) = 9.8 psi P element = [76 x ( ) x (44 32) = 0.7 bar] P total = = 10.8 psi P element = [ =.77 bar] P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (25) (75) (125) Flow gpm sp gr = specific gravity P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 8Z3.25 8Z Z ZZ1.37 8ZZ3.21 8ZZ5.13 8ZZ ZZ25.08 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. Dirt Alarm Part No. Seal Inlet Outlet (See Appendix A f Series Length Media Material Pting Pting complete list of options) **When H seals are dered all aluminum filter parts are anodized. **Only available with Buna N seals. See also Accessies f Tank- s section. (0.50) (0.25) P (bar) (Omit) = Nonthreaded OP = NPTF Male Y2 = Back Tri-Col Gauge Y2C = Bottom Gauge in Cap Y5 = Back Gauge in Cap ES = Electric Switch ES1 = Heavy-Duty Electric Switch with Conduit Connection See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 109

13 Tank- 100 gpm 380 L/min 100 psi 7 bar 6.25 MAX. (159) OPTIONAL DI ALARM OR ELECTRIC SWITCH OPTIONAL LET PO 4.31 (110) SEE CHA CTO TANK TOP.12 (3) THICK GASKET 5.06 (129) Ø HOLE TANK FOR ALLATION 45 TYP. SEE CHA PO TO PO 7.00 Ø (178).44 (11) Ø ON A 6.25 (159) Ø B.C. (4) MOUNTG HOLES 1K = 8.81 (224) 2K = (457) 3K = (694) 1 1 4, Standard Pts Pts 4-Bolt Flange Only 2 Pts Pt to Pt (P, S, B) 7.38 (F) C L to Casting Base C L to Tank Top (66) 4.50 Ø (114).88 (22) OPTIONAL CHECK VALVE Optional mounting ring available to weld to tank. Metric dimensions in ( ). Model No. of filter in photograph is 1K10S24NP16CY2. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head & Cap: Case: Weight of -1K: Weight of -2K: Change Clearance: Up to 100 gpm (380 L/min) f 150 SUS (32 cst) fluids 100 psi (7 bar) 400 psi (28 bar) 90 psi (6 bar), per NFPA T F to 225 F (-29 C to 107 C) Cracking: 25 psi (1.7 bar) Full Flow: 48 psi (3.3 bar) Die Cast Aluminum Steel 11.4 lbs. (5.2 kg) 14.5 lbs. (6.6 kg) 8.0 (205 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm K N/A N/A 54 K N/A N/A 44 KZ1 <1.0 <1.0 <1.0 < KZ3 <1.0 <1.0 < KZ KZ KZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In See, page 114 f inside out flow version. Nominal Dimensions: 4.0 (100 mm) O.D. x 9.0 (230 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) Media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z Media with EPR Seals, K3H and K10H E Media Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

14 Tank- Meets HF4 automotive standard. Top, side bottom mounting. Optional check valve prevents reservoir siphoning. Up to 3 inlet pts available. W model allows filter to be welded to tank instead of bolted. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 25 psi (1.7 bar) bypass valve. Return Line -Tank- Inlet Pting Options Identify All Pts No. of Seal Outlet Pting Series s Part No. Material Pt A Pt B Pt C Options K3 K10 K25** 1 E Media Z Media Flow KZ1 2 KZ3 KZ5 KZ10 3 KZ25 W KM60 KW Inlet Pting Location K3 1K3 2K3 3K3 K10 1K10 2K10 K25 1K25 2K25 KZ1 1KZ1 2KZ1 KZ3 1KZ3 2KZ3 KZ5 1KZ5 2KZ5 KZ10 KZ25 (Omit) = Buna N H = EPR* W = Buna N* P16 P20 P24 P32 S16 S20 S24 S32 F20 F24 F32 B24 P16 P20 P24 P32 S16 S20 S24 S32 F20 F24 F32 B24 N=None 1KZ10 1KZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 80 gpm (300 L/min) f 1KZ10P24NN using 200 SUS (44 cst) fluid. Solution: P housing = 3.0 psi [.20 bar] P element = 80 x.05 x ( ) = 5.3 psi P element = [300 x ( ) x (44 32) =.38 bar] P total = = 8.3 psi P element = [ =.58 bar] P housing f fluids with sp gr = 0.86: P2 P16 S16 N = None P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 1K 2K K K K KZ KZ KZ KZ KZ If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). sp gr = specific gravity Sizing of elements should be based on element flow infmation provided in the chart above. P psi Flow (L/min) (50) (150) (250) (350) Flow gpm (0.50) (0.25) (Omit) = NPT Male C = Check Valve D = Diffuser CD = Check Valve & Diffuser T = 13 Tube Extension A = Nonthreaded Outlet S32= SAE Straight **When H W seals are dered all aluminum filter parts are anodized. **Not available with EPR seals. Double and triple stacking of elements can be replaced by single KK and 27K elements, respectively. Note: W allows filter to be welded to tank instead of bolted. G501 = Rubber gasket G547 = Two 1 8 gauge pts G820 = Stamped cap N=No-element indicat See also Accessies f Tank- s section. If using Pt B, Pt A & B must always be the same type and size. Example: (A) P20 (B) P20 (C) P16 P=NPTF, S=SAE Straight, F= SAE J518 4-Bolt Flange Code 61, B=BSPP 2= 1 8,16=1,20=1 1 4, 24=1 1 2,32=2 M = Metric thread f SAE 4-bolt flange mounting holes (specify after each F pt designation) P (bar) Dirt Alarm (See Appendix A f complete list of options) Pt D: (Omit) = None Y2 = Tri-col Gauge ES = Electric Switch ES1 = Electric Switch with Conduit Connect Located in Cap: Y2C = Bottom Gauge Pt C: Y2R = Back Gauge ESR = Electric Switch ES1R = Electric Switch with Conduit Connect See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 111

15 Tank- Duplex NEW PRODUCT 100 gpm 380 L/min 100 psi 7 bar (129) DIA. HOLE TANK 8.00 M. CLEARANCE REQUIRED FOR ELEMENT REMOVAL OPTIONAL DI ALARM OR ELECTRIC SWITCH 1 ELEMENT 8.81 (224) 2 ELEMENT (457) 3 ELEMENT (694) 6.25 [159] MAX 4.50Ø BACK DI ALARM LOCATIONS BACK 2.59 FRONT FRONT Metric dimensions in ( ). Model No. of filter in photograph is 2KZ10P24. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head & Cap: Case: Weight of -1K: Weight of -2K: Change Clearance: Up to 100 gpm (380 L/min) f 150 SUS (32 cst) fluids 100 psi (7 bar) 400 psi (28 bar) 90 psi (6 bar), per NFPA T2.6.1.R F to 225 F (-29 C to 107 C) Cracking: 25 psi (1.7 bar) Full Flow: 48 psi (3.3 bar) Die Cast Aluminum Steel 29.2 lbs. (13.3 kg) 35.4 lbs. (16.1 kg) 8.0 (205 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm K N/A N/A 54 K N/A N/A 44 KZ1 <1.0 <1.0 <1.0 < KZ3 <1.0 <1.0 < KZ KZ KZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 4.0 (100 mm) O.D. x 9.0 (230 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol 112 Appropriate Schroeder Media All Paper (E) and Synthetic (Z) Media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z Media with EPR Seals, K3H and K10H E Media Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and 20.

16 NEW PRODUCT Tank- Duplex Diversion valve allows f uninterrupted flow during element change. Meets HF4 automotive standard. Top, side bottom mounting. Optional check valve prevents reservoir siphoning. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 25 psi (1.7 bar) bypass valve. Return Line -Tank- E Media Z Media Flow K3 1K3 2K3 3K3 K10 1K10 2K10 K25 1K25 2K25 KZ1 1KZ1 2KZ1 KZ3 1KZ3 2KZ3 KZ5 1KZ5 2KZ5 KZ10 KZ25 1KZ10 1KZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element The P housing curve labeled Sizing is the pressure drop between the inlet and outlet areas of the filter s bypass valve and should be used f filter sizing. The Pt to Pt P takes into consideration any manifolds and/ special valving. This pressure drop can be significantly higher due to these additional flow constrictions. Although this P does not affect the perfmance of the filter, it should be considered f overall system design. G547 = Two 1 8 gauge pts G820 = Stamped cap See also Accessies f Tank- s section. P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (100) (200) PO TO PO M = Metric thread f SAE 4-bolt flange mounting holes (specify after each F pt designation) P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 1K 2K K K K KZ KZ KZ KZ KZ If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). sp gr = specific gravity Sizing of elements should be based on element flow infmation provided in the chart above. (300) ELEMENT SIZG Flow gpm Seal Inlet Outlet Series Length Model No. Material Pting Options Pting Options K3 K10 K25 KZ1 KZ3 KZ5 KZ10 KZ25 KM60 KW (Omit) = Buna N H = EPR (Aluminum Parts Anodized) P16 =1 NPTF P20 =1 1 4 NPTF P24 =1 1 2 NPTF P32 =2 NPTF S16 = SAE Straight (SAE-16) S20 = SAE Straight (SAE-20) S24 = SAE Straight (SAE-24) S32 = SAE Straight (SAE-32) F20 =1 1 4 SAE J518 Split Flange Code 61 F24 =1 1 2 SAE J518 Split Flange Code 61 F32 =2 SAE J518 Split Flange Code 61 B24 =ISO 228 G1 1 2 (1.00) (0.75) (0.50) (0.25) P (bar) (Omit) = 1.50 NPTM A = Non Threaded C = Check Valve D = Diffuser CD = Check Valve and Diffuser T = 13" Tube Extension Dirt Alarm (See Appendix A f complete list of options) Located in Front: (Omit) = None Y2 = Tri-col Gauge ES = Electric Switch ES1 = Electric Switch with Conduit Connect Located in Cap: Y2C = Bottom Gauge Located in Back: Y2R = Back Gauge ESR = Electric Switch ES1R = Electric Switch with Conduit Connect See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 113

17 Tank- (Inside Out Flow) NEW PRODUCT 120 gpm 455 L/min 100 psi 7 bar 6.25 MAX. (159) OPTIONAL DI ALARM OR ELECTRIC SWITCH 45 TYP (110) OPTIONAL LET PO SEE CHA C TO TANK TOP.12 (3) THICK GASKET 5.06 (129) Ø HOLE TANK FOR ALLATION SEE CHA PO TO PO 7.00 Ø (178).44 (11) Ø ON A 6.25 (159) Ø B.C. (4) MOUNTG HOLES KI ELEMENT LENH = 9.75 (248) KKI ELEMENT LENH = (481) 27KI ELEMENT LENH = (729) 4.50 Ø (114) 1 1 4, Standard Pts Pts 4-Bolt Flange Only Pt to Pt C L to Casting Base C L to Tank Top Metric dimensions in ( ). Model No. of filter in photograph is 3KZ10S24NP16Y2. Optional mounting ring available to weld to tank. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head & Cap: Case: Weight of -KI: Weight of -KKI: Change Clearance: Up to 120 gpm (455 L/min) f 150 SUS (32 cst) fluids 100 psi (7 bar) 400 psi (28 bar) Contact facty -20 F to 225 F (-29 C to 107 C) Cracking: 25 psi (2 bar) Full Flow: 62 psi (4.3 bar) Die Cast Aluminum Steel 11.4 lbs. (5.2 kg) 14.5 lbs. (6.6 kg) KI = 9.00 (229 mm) KKI = (457 mm) 27KI = (686 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Dirt Holding Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Capacity gm ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 K/KK/27K KIZ1 <1.0 <1.0 <1.0 < /181/276 KIZ3 <1.0 <1.0 < /185/283 KIZ10 <7.4 <8.2 < /174/266 Collapse Rating: 100 psid (7 bar) Flow Direction: Inside Out Nominal Dimensions: KI: 4.0 (100 mm) O.D. x 9.0 (230 mm) long KKI: 4.0 (100 mm) O.D. x 18.0 (460 mm) long 27KI: 4.0 (100 mm) O.D. x 27.0 (690 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) Media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z Media with EPR Seals, K3H and K10H E Media Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

18 NEW PRODUCT Tank- (Inside Out Flow) Inside out flow direction. Top, side bottom mounting. Optional check valve prevents reservoir siphoning. Up to 3 inlet pts available. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 25 psi (1.7 bar) bypass valve. Return Line -Tank- Z Media Z10 KI KKI 27KI Flow gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 80 gpm (300 L/min) f KKIZ10P24NN using 200 SUS (44 cst) fluid. Solution: P housing = 3.0 psi [.20 bar] P element = 80 x.05 x ( ) = 5.3 psi P element = [300 x ( ) x (44 32) =.38 bar] P total = = 8.3 psi P element = [ =.58 bar] Inlet Pting Options Identify All Pts Seal Series Part No. Material Pt A Pt B Pt C KIZ1 KIZ3 KIZ10 KKIZ1 KKIZ3 KKIZ10 27KIZ1 27KIZ3 27KIZ10 (Omit) = Buna N H = EPR* W = Buna N* P housing f fluids with sp gr = 0.86: P16 P20 P24 S16 S20 S24 F20 F24 P16 P20 P24 S16 S20 S24 F20 F24 N = None P2 P16 S16 N = None P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): KIZ10.08 KKIZ KIZ10.04 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. Inlet Pting Location Flow (L/min) (50) 10 (150) (250) (350) (454) Flow gpm sp gr = specific gravity **When H W seals are dered all aluminum filter parts are anodized. G547 = Two 1 8 gauge pts See also Accessies f Tank- s section. P psi If using Pt B, Pt A & B must always be the same type and size. Example: (A) P20 (B) P20 (C) P16 P=NPTF, S=SAE Straight, F= SAE J518 Split Flange Code 61 2= 1 8,16=1,20=1 1 4, 24=1 1 2 (0.50) (0.25) M = Metric thread f SAE 4-bolt flange mounting holes (specify after each F pt designation) P (bar) Dirt Alarm (See Appendix A f complete list of options) Pt D: (Omit) = None Y2 = Tri-col Gauge ES = Electric Switch ES1 = Electric Switch with Conduit Connect Located in Cap: Y2C = Bottom Gauge Pt C: Y2R = Back Gauge ESR = Electric Switch ES1R = Electric Switch with Conduit Connect See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 115

19 Tank- 100 gpm 380 L/min 100 psi 7 bar 7.00 Ø (178) 1K = (345) 2K = (583) 5.12 (130) 1.78 (45) OPTIONAL MOUNTG RG.44 (11) Ø ON A 6.25 (159) Ø B.C. (4) MOUNTG HOLES ON OPTIONAL MTG. RG 6.06 MAX. (154).12 (3) THICK GASKET 45 OPTIONAL CHECK VALVE 6.82 Ø (173) 2.59 (66).88 (22) OPTIONAL DI ALARM OR ELECTRIC SWITCH Metric dimensions in ( ). Model No. of filter in photograph is 1K10P24P24NBY2. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Cap: Case: Weight of -1K: Weight of -2K: Change Clearance: Up to 100 gpm (380 L/min) f 150 SUS (32 cst) fluids 100 psi (7 bar) 400 psi (27 bar) Contact facty -20 F to 225 F (-29 C to 107 C) Cracking: 25 psi (1.7 bar) Full Flow: 48 psi (3.3 bar) Die Cast Aluminum (standard), Steel (optional) Steel 10.0 lbs. (4.5 kg) 13.6 lbs. (6.2 kg) 8.0 (205 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm K N/A N/A 54 K N/A N/A 44 KZ1 <1.0 <1.0 <1.0 < KZ3 <1.0 <1.0 < KZ KZ KZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 4.0 (100 mm) O.D. x 9.0 (230 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) Media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z Media with EPR Seals, K3H and K10H E Media Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

20 Tank- Meets HF4 automotive standard. Variety of inlet/outlet pting options. Top, side bottom mounting. Optional check valve prevents reservoir siphoning. Can also be used in return line application. Contact facty. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 25 psi (1.7 bar) bypass valve. Return Line -Tank- P filter = P housing + P element P housing P element Exercise: Determine P at 80 gpm (300 L/min) f 2K10P24 using 200 SUS (44 cst) fluid. Solution: P housing = 3 psi [.25 bar] P element = 80 x.05 x ( ) = 5.3 psi P element = [300 x ( ) x (44 32) =.37 bar] P total E Media Z Media Flow = = 8.3 psi P element = [ =.62 bar] K3 1K3 2K3 K10 1K10 2K10 K25 1K25 2K25 KZ1 1KZ1 2KZ1 KZ3 1KZ3 2KZ3 KZ5 1KZ5 2KZ5 KZ10 1KZ10 KZ25 1KZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (50) (150) (250) (350) Flow gpm sp gr = specific gravity Sizing of elements should be based on element flow infmation provided in the chart above. Inlet Pting Options No. of Seal Pt 1 Pt 2 Pt 3 Pt 4 Outlet Pting Series Ele. Part No. Material (Std) (Opt) (Opt) (Opt) Pt Size Options 1 2 K3 K10 K25** KZ1 KZ3 KZ5 KZ10 KZ25 (Omit) = Buna N H = EPR* W = Buna N* P24 P20 P16 P12 P8 P4 P2 S24 S20 S16 S12 S8 S4 F24 F32 N P24 P20 P16 P12 P8 P4 P2 S24 S20 S16 S12 S8 S4 F24 F32 N P24 P20 P16 P12 P8 P4 P2 S24 S20 S16 S12 S8 S4 N P24 P20 P16 P12 P8 P4 P2 S24 S20 S16 S12 S8 S4 N = None 1.50 NPTF 1.25 NPTF 1.00 NPTF 0.75 NPTF 0.50 NPTF 0.25 NPTF 0.12 NPTF Flange 2.0 Flange (0.50) (0.25) P (bar) P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 1K 2K K K K KZ KZ KZ KZ KZ If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). N = Non-Threaded (Omit) = NPTM T = Non- Threaded Tube C = Check Valve D = Diffuser CD= Check Valve and Diffuser Optional Mounting Flange (Omit) = None B = Flange with 4 Holes BW = Flange with no Holes (Omit) = None Y2 = = Back Tri-Col Gauge (Pt 4) (Not Available with 4 Pts) Y2C = = Bottom Gauge in Cap Y5 = = Back Gauge in Cap ES = = Electric Switch (Located on Housing Not Available with 4 Pts) **When H W seals are dered all aluminum filter parts are anodized. **Not available with EPR seals. Double and triple stacking of K-size elements can be replaced by single KK and 27K elements, respectively. G501 = Rubber gasket M = Metric thread f SAE 4-bolt G820 = Stamped cap flange mounting holes (specify after each F pt designation) See also Accessies f Tank- s section. Dirt Alarm (See Appendix A f complete list of options) See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 117

21 L Tank- 150 gpm 570 L/min 100 psi 7 bar 6.25 MAX. (159) OPTIONAL DI ALARM OR ELECTRIC SWITCH OPTIONAL LET PO 4.31 (110) SEE CHA C TO TANK TOP 5.06 (129) Ø HOLE TANK FOR ALLATION.12 (13) THICK GASKET 45 TYP. SEE CHA PO TO PO.44 (11) Ø ON A 6.25 (159) Ø B.C. (4) MOUNTG HOLES 18L = (477) 7.00 Ø (178) 4.50 Ø (114) 1 1 4, Standard Pts Pts 4-Bolt Flange Only 2 Pts Pt to Pt (P, S, B) 7.38 (F) C L to Casting Base C L to Tank Top Optional mounting ring available to weld to tank. Metric dimensions in ( ). Model No. of filter in photograph is L18LZ10S24NP16Y (70).88 (22) OPTIONAL CHECK VALVE Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head & Cap: Case: Weight of L-18L: Change Clearance: Up to 150 gpm (570 L/min) f 150 SUS (32 cst) fluids 100 psi (7 bar) 400 psi (28 bar) 90 psi (6 bar), per NFPA T F to 225 F (-29 C to 107 C) Cracking: 25 psi (1.7 bar) Full Flow: 34 psi (2.3 bar) Die Cast Aluminum Steel 14.6 lbs. (6.6 kg) 17.0 (435 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 18L N/A N/A L N/A N/A 88 18LZ1 <1.0 <1.0 <1.0 < LZ3 <1.0 <1.0 < LZ LZ LZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 4.0 (100 mm) O.D. x 18.5 (470 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5 and Z25H.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

22 Tank- L Available with multi inlet pts. Optional check valve prevents reservoir siphoning. Top, side bottom mounting. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 25 psi (1.7 bar) bypass valve. Return Line -Tank- Z Media Flow 18LZ1 18LZ1 See 18LZ3 18LZ3 18LZ5 18LZ5 18LZ10 18LZ10 18LZ25 18LSZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 120 gpm (455 L/min) f L18LZ5P24Y2 using 200 SUS (44 cst) fluid. Solution: P housing = 3.0 psi [.20 bar] P element = 120 x.04 x ( ) = 6.4 psi P element = [455 x ( ) x (44 32) =.45 bar] P total = = 9.4 psi P element = [ =.65 bar] L P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (100) (300) (500) Flow gpm sp gr = specific gravity P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 18L 18LZ LZ LZ LZ LZ25.02 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. Inlet Pting Options Identify All Pts Part No. Seal Outlet Pting Series Length Media Material Pt A Pt B Pt C Options L 18 L3 L10 LZ1 LZ3 LZ5 LZ10 LZ25 Inlet Pting Location (Omit) = Buna N H = EPR* W = Buna N* P16 P20 P24 P32 S16 S20 S24 S32 F20 F24 F32 B24 P16 P20 P24 P32 S16 S20 S24 S32 F20 F24 F32 B24 N=None P2 P16 S16 N = None *When H W seals are dered all aluminum filter parts are anodized. G501 = Rubber gasket G547 = Two 1 8 gauge pts G820 = Stamped cap See also Accessies f Tank- s section. If using Pt B, Pt A & B must always be the same type and size. Example: (A) P20 (B) P20 (C) P16 P=NPTF, S=SAE Straight, F= SAE J518 4-Bolt Flange Code 61, B=BSPP 2= 1 8,16=1,20=1 1 4, 24 =1 1 2,32=2 S32= SAE Straight M = Metric thread f SAE 4-bolt flange mounting holes (specify after each F pt designation) (0.50) (0.25) P (bar) (Omit) = 2 NPT Male C = Check Valve D = Diffuser T = 13 Tube Extension A = Non- Threaded Outlet Dirt Alarm (See Appendix A f complete list of options) Pt D: (Omit) = None Y2 = Tri-col Gauge ES = Electric Switch ES1 = Electric Switch with Conduit Connect Located in Cap: Y2C = Bottom Gauge Pt C: Y2R = Back Gauge ESR = Electric Switch ES1R = Electric Switch with Conduit Connect See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 119

23 Tank- 300 gpm 1135 L/min 100 psi 7 bar 6.62 (168) 3.43 (87) (451) 6.00 Ø (152).12 (3) THICK GASKET 6.75 MAX. (171) OPTIONAL DI ALARM OR ELECTRIC SWITCH 45 D. PO OPTIONAL PO 9.25 Ø (235) 1BB = (579).56 (14) Ø ON A 8.38 (213) Ø B.C. (4) MOUNTG HOLES 1.50 (38) FOR PIPE/RAIGHT FOR 4-BOLT FLANGE 9.00/(229) 8.75/(222) OPTIONAL CHECK VALVE Metric dimensions in ( ). Model No. of filter in photograph is 1BBZ10FFY2. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head & Cap: Case: Weight of -1BB: Change Clearance: Up to 300 gpm (1135 L/min) f 150 SUS (32 cst) fluids 100 psi (7 bar) 250 psi (17 bar) Contact facty -20 F to 225 F (-29 C to 107 C) Cracking: 25 psi (1.7 bar) Full Flow: 52 psi (3.6 bar) Aluminum Steel 36.7 lbs. (16.6 kg) (375 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm BB N/A N/A 132 BBZ1 <1.0 <1.0 <1.0 < BBZ3 <1.0 <1.0 < BBZ BBZ BBZ Collapse Rating: Flow Direction: Nominal Dimensions: 150 psid (10 bar) Outside In 5.0 (125 mm) O.D. x 18.0 (460 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5 and Z25H.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. 120 F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and 20.

24 Tank- Dual inlet pting. Top, side bottom mounting. Optional check valve prevents reservoir siphoning. selections are predicated on the use of 150 SUS (32 cst) petroleum Pressure Series Part No. based fluid and a 25 psi (1.7 bar) bypass valve (with check valve option). Return Line -Tank- 1 E BB10 1BB10 See MLF Media BB25 1BB25 BBZ1 *BBZ1* BBZ3 *BBZ3* Z Media BBZ5 BBZ5 BBZ10 BBZ10 BBZ25 BBZ25 Flow BB10** BB25** BBZ1 BBZ3 BBZ5 BBZ10 BBZ25 G547 = Two 1 8 gauge pts G1476 = Three terminal electric switch gpm (L/min) Shown above are the elements most commonly used in this housing. *Note: Additional per element flow is available up to 300 gpm when using filter without check valve option. See housing pressure drop graph below. P filter = P housing + P element P housing P element Exercise: Determine P at 160 gpm (600 L/min) f 1BBZ3PCY2 using 200 SUS (44 cst) fluid. Solution: P housing = 2.5 psi [.20 bar] P element = 160 x.05 x ( ) = 10.7 psi P element = [600 x ( ) x (44 32) =.8 bar] P total = = 13.2 psi P element = [ = 1.0 bar] (Omit) = Buna N H = EPR* W = Buna N* P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (400) (600) (800) sp gr = specific gravity P= NPTF PP = Dual NPTF S= SAE Straight (SAE-32) SS = Dual SAE Straight (SAE-32) F= SAE J518 4-Bolt Flange Code 61 W/ CHECK VALVE FF = Dual SAE J518 4-Bolt Flange Code 61 P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): BB BB10.03 BB25.01 BBZ1.07 BBZ3.05 BBZ5.04 BBZ10.03 BBZ25.02 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. (1000) W/O CHECK VALVE Flow gpm No. of Seal Outlet Optional Series Ele. Part No. Material Pting Pting Check Valve **When H W seals are dered, all aluminum filter parts are anodized. **Only available with Buna N seals. See also Accessies f Tank- s section. (Omit) = 3 NPT Male (0.50) (0.25) T = 13" Tube Extension M = Metric thread f SAE 4-bolt flange mounting holes (specify after each F pt designation) P (bar) (Omit) = None C = Check Valve Dirt Alarm (See Appendix A f complete list of options) Y2 = Tri-Col Gauge ES = Electric Switch ES1 = Heavy-Duty Electric Switch with Conduit Connection See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 121

25 Accessies f Tank- s Mounting Ring f,,,, and L Models The mounting ring is welded directly to the hydraulic reservoir. The filter is then mounted to the mounting ring with bolts converting the filter to a weld in design. The mounting ring eliminates the need to drill and tap the hydraulic reservoir. Model Part Number Number A B C,,, A-LFT-813, L (178) (127) (25) GASKET C,,,, L High Version A-LFT-1448 A-LFT (178) (127) (38) (159) (92) (22) MOUNTG RG WELDED TO TANK B A Diffuser f,, L, and Models The diffuser option (designated as D f outlet pting option in model number) is threaded to the bushing on the filter bowl below the outlet opening to help decrease turbulent flow in the hydraulic reservoir. No other outlet pt options are available if the diffuser is used. Model Part Number Number NPTF,, A-LFT L A-LFT (76) 4.00 O.D. (102) Check Valve f,,, L,, and Models The check valve option (designated as C f outlet pting option in model number) makes it possible to service the filter without draining the oil from the reservoir when the filter is mounted below the oil level. It also prevents reservoir siphoning when system components are serviced. The check valve can also be used on other reservoir return flow lines, where components upstream of the check valve can be serviced without the loss of reservoir oil. The spring setting is psi cracking. Order by part number shown in chart. No other outlet pt options are available if the check valve is used. Model Part Number Number NPTF A,,, A-LFT-158Q (59) L A-LFT (59) A (114) A 122

26 Accessies f Tank- s 3.50 (89) (330) 2.94 (75) A 3.90 Ø (99) Note: No other outet pt options are available if the tube adapter is used. 45 The diffuser/check valve option (designated as CD f outlet pting option in model number) is threaded on to the outlet pt and combines the advantages of both separate options in one assembly. Available as a separate item with NPT female threads, der part number A-LFT No other outlet pt options are available if the check valve/diffuser is used. The tube adapter outlet pt option (designated as T f outlet pting option in model number) provides the means to direct flow to the bottom of the hydraulic reservoir. Other tube lengths are available f quantity purchases. Contact your Schroeder distribut f details. Model Dimension A Number (O.D.),, 1.62 (41) L 2.25 (57) 3.50 (89) The threaded male outlet pt is standard on the, L,, and models, and is available as an option on the filter by designating OP f the outlet pting options in the model number. and are furnished with NPT Male (standard) L is furnished with 2 NPT Male (standard) is furnished with 3 NPT Male (standard) is furnished with NPT Male (optional) is furnished with NPT Male (standard) Check Valve Diffuser Combination f, and Models Tube Adapter Outlet Pt f,,, L and Models Threaded Outlet Pt f,,, L,, and Models SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 123

27 Installing an efficient air breather is a critical yet often overlooked component when system filtration is considered. On systems operating in dusty atmospheric conditions that experience significant changes in reservoir levels, the use of an air breather will minimize the ingestion of airbne particles as the fluid level drops. By lowering the rate of ingression of dirt, the contamination level of the system will be reduced and the service life of the system s fluid filters will be increased. Schroeder ABF and MBF style air breathers feature large pleated surface areas which remove airbne particles three microns and above with exceptional dirt holding capacity. Higher dirt holding capacities extend the life of the air breather and thus the length of time between servicing. The ABF-S40 models are recommended f mobile applications and other situations where frequent oil splashing occurs. The Schroeder D-AB-2 desiccant filter breather features a dual filtration process, removing water as well as solid contaminants (2 micron absolute). Moisture can decrease a fluid s stability and reduce its service life, as well as cause oxidation and rust. Use of the D-AB-2 keeps air entering a reservoir clean and dry. Breathers with NPT Adapters Schroeder air breathers allow high capacity air flows and are available with both NPT and flange adapters. As can be seen on the opposite page, a variety of options are available with the flange style adapter. All flange style air breathers possess the same high capacity air flows as those shown in the table f the breathers with NPT adapter. ABF-3/10 ABF-3/10-M-P12 ABF-S40 MBF-3-M-P20 MBF-10-M-P20 A B Specifications: Breathers with NPT Adapters Model Nmal Air Flow/ Number A B Adapter Type Capacity psi Drop ABF-3/10.75" NPT Nylon 0.4 psi at 20 SCFM (94) 4.28 (109) 40 SCFM ABF-3/10-M-P12.75" NPT Steel 1.25 psi at 40 SCFM ABF-S (94) 4.28 (109).75" NPT Steel MBF-3-M-P20 MBF-10-M-P20 SCFM = Standard Cubic Feet per Minute 5.06 (128) 8.31 (211) 1.25" NPT Steel 200 SCFM 200 SCFM 0.29 psi at 20 SCFM psi at 40 SCFM 0.3 psi at 70 SCFM psi at 200 SCFM Desiccant Breather D-AB-2 D-AB-2-F NEW PRODUCT 3.25Ø D-AB-2 2um/Water Removal Desiccant Breather Made in the USA Schroeder desiccant breathers are made with environmentally disposable silica gel, which adsbs and traps moisture. They are available with two connection styles as shown in the chart below. Specifications: Model Number D-AB-2 D-AB-2-F Adapter.75" NPT Male 2.25" SAE J829 Flange 124

28 ABF-3/10-F, ABF-S40-F These breathers are designed f retrofit on hydraulic reservoirs using the SAE-type flange fill pt assembly. ABF-3/10FA, B, C, ABF-S40FA, B, C Breathers with Dipstick The air breathers above are also available with a dipstick up to 24 inches in length. The dimensions to the add line and the fill line must be specified in the model number ABF-3/10-F, A, B, C, where: A = overall length of the dipstick in inches B = length from tip of dipstick to fill line in inches C = length from tip of dipstick to add line in inches F safety reasons, the tip of the dipstick is rounded. No tools are needed f installation and removal. A quarter turn should snugly seal the breather in place. Minimum der quantity is 12. LBF (13) OVERALL LENH, A MAX. = 24 (610) (90) 3.57 (91) FILL LE ADD LE 3.75 Ø (TYP) (95) 3.69 Ø (94) SAE-TYPE FLANGE ADAPTER LENH TO ADD LE, C P SAE-TYPE FLANGE ADAPTER This extra large capacity air breather is supplied with its cresponding replaceable element (P/N BF10) installed. The LBF-10 boasts a nmal capacity of 800 SCFM, with an impressive air flow/psi drop of only SCFM. This giant air breather and its replacement element have a minimum der quantity of 6. A 14mm (.551 Ø) MOUNTG HOLES (12) PLACES EQUALLY SPACED.25 Ø DRA ON A Ø B.C. A HOLES (4) PLACES SECTION A-A Ø Ø TANK LENH TO FILL LE, B Ø Ø CUT- Breathers with Flange Adapters High Capacity Air Breather NEW PRODUCT SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 125

29 Filler Strainer Assemblies Filler Breather with Strainer ABF-3/10-S ABF-3/10-S6 ABF-S40-6 ABF-S40-S6 The strainer used here is #24 mesh and is available in the lengths shown Ø (94) 4.48 (114) #26 DRILL (6 HOLES) ON A 2.88 (73) B.C. -S = 3.71 (94) -S6 = 6.00 (152) 2.12 (54) DIA. HOLE MOUNTG REQUIREMENT RAER Rapid Fill Cap and Strainer A-TB-779 A-TB-780 Speed the process of adding fluid to a reservoir by using our rapid fill cap and strainer. The strainer is 4.38 in diameter and designed to accept cold viscous fluids easily. Choose from two strainer mesh sizes: A-TB-779, which features #24 mesh, and A-TB-780, which is supplied with #70 mesh. The cap completely seals the opening. All assemblies are supplied with necessary hardware, including retaining chain f cap and self tapping screws f installation. #26 DRILL (6) HOLES ON A 4.94 (125) B.C. ( TANK LID) RETAG CHA Specifications: A-TB s Model Mesh Strainer Strainer Flange Number Size O.D. Height Diameter A-TB A-TB (111) (100) (141) Metric dimensions in ( ) (33) GASKET CAP 4.41 Ø (112) #26 DRILL ON A 4.50 (114) RADIUS ( TANK LID) RESERVOIR 3.94 (100) 4.50 (114) DIA. HOLE REQUIRED FOR ALLATION ( TANK LID) 4.38 Ø 126

30 Magnetic Suction Separats With the use of Schroeder s Magnetic Suction Separats, suction line filtration is provided without starving the pump. They offer unique protection f pumps from all sizes of ferrous particles, some of which have the potential of destroying a pump in a single pass. Large ceramic magnets are spaced along the length of the separat. All hydraulic fluid entering the pump must move at low velocity through a powerful magnetic field. This field traps large quantities of micronic ferrous particles. The viscous properties of the fluid can cause some non-ferrous particles to adhere to the magnetically trapped particles. Schroeder SKB s are available in sizes ranging from one to three inches. The chart below shows the part numbers, specifications, and dimensions of available models. B C Complete Pipe Flow psi at Dimensions Model Number Size gpm Max. gpm A B C SKB (55) (133) 3.25 (83) 1.62 (41) SKB (95) (210) 3.50 (89) 3.00 (76) SKB (135) (210) 3.50 (89) 3.00 (76) SKB (190) (210) 3.50 (89) 3.00 (76) SKB (380) (254) 4.75 (121) 4.00 (102) Metric dimensions in ( ). The standard outer screen has adequate open area (.079 inch diameter perfations) to eliminate the possibility of pump starvation. All models are also available with a pleated 20 mesh screen (850 micron) by adding SS20 to the model number. (Example SKB-1-SS20.) Please note that we also offer in-line filter housings equipped with SKB elements. See In-Line Magnetic Suction Separats and Tank- Magnetic Suction Separats (pages ) f details. A SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 127

31 These all metal suction strainers are furnished with optimized pleat size and screen area f extended life and low pressure drop. 100 mesh stainless steel screen (140 micron) has 33.3% open area. Pting head is carbon steel, center ce is plated perfated steel. End cap is heavy gauge zinc plated steel. These strainers can handle temperatures up to 250 F (121 C). 60 mesh (238 micron) and 200 mesh (74 micron) models also available contact facty. Our externally mounted suction strainers (ESS) are functionally equivalent to our standard strainers with the added feature of being installed through the wall of the reservoir. They are available with an optional 3 psi bypass valve. TO PUMP RESERVOIR C A B NPT THREAD Model Number Other Optional Dimensions Screen Basic 3 psi Pipe Flow* Area Model Bypass Size gpm (L/min) A B C in 2 (cm 2 ) SS (Omit) = (19) 3.10 (79) 2.63 (67) 1.12 (28) 62 (400) SS None (30) 3.55 (90) 2.63 (67) 1.31 (33) 88 (567) SS (38) 5.35 (136) 2.63 (67) 1.62 (41) 110 (710) SS = (76) 6.85 (174) 3.38 (89) 1.88 (48) 162 (1045) SS Bypass (114) 8.01 (204) 3.38 (89) 2.12 (54) 225 (1450) SS valve 2 50 (189) 9.85 (250) 3.94 (100) 2.75 (70) 340 (2200) SS (284) (257) 5.12 (130) 3.50 (89) 400 (2580) SS (379) (299) 5.12 (130) *Flow rating based on 5 FPS less. Metric dimensions in ( ). Examples: SS SS suction strainer, 2 NPT, without bypass valve. SS SS suction strainer, 1 NPT, with 3 psi bypass valve (102) Round 500 (3225) 128

32 (B) TERNAL THREAD (D) BUSHG (A) EXTERNAL THREAD (C) OVERALL LENH OPTIONAL 3 PSI BYPASS VALVE Model Number Optional Flow A B C D E F Screen Basic 3 psi Rating External Internal Overall Bushing End Cap Hex Area Model Bypass gpm (L/min) Thread Thread Length Length O.D. Size in 2 (cm 2 ) ESS-10P (Omit) = 10 (38) 1 1 4" NPT 3 4" NPT 8.18 (208) 1.20 (30) 1.38 (35) 1.75 (44) 64 (413) ESS-15P None 15 (57) 1 1 2" NPT 1" NPT 8.25 (210) 1.23 (31) 1.66 (42) 2.00 (51) 87 (561) ESS-25P 25 (95) 2" NPT 1 1 4" NPT 9.03 (229) 1.33 (34) 2.12 (54) 2.50 (64) 125 (806) ESS-50P -3 = 50 (189) 3" NPT 2" NPT 9.70 (246) 1.68 (43) 3.00 (76) 3.25 (83) 260 (1677) ESS-100P Bypass 100 (379) 4" NPT 3" NPT (287) 1.75 (44) 3.94 (100) 4.62 (117) 315 (2032) ESS-10S valve 10 (38) 1 5 8"-12 SAE "-12 SAE 8.00 (203) 1.19 (30) 1.38 (35) 1.88 (48) 64 (413) ESS-15S 15 (57) 1 7 8"-12 SAE 1 5 8"-12 SAE 8.38 (213) 1.60 (41) 1.66 (42) 2.12 (54) 87 (561) ESS-25S 25 (95) 2 1 2"-12 SAE 1 7 8"-12 SAE 8.90 (226) 1.50 (38) 2.12 (54) 2.75 (70) 125 (806) Metric dimensions in ( ).. (E) END CAP O.D. S I C N H R D U S (F) O T E R D E E WIDTH ACROSS FLATS I R S NEW PRODUCT SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 129

33 Spin-On 20 gpm 75 L/min 100 psi 7 bar 1.88 (48).38 (10) 1.50 (38) 1.12 (28) 3.75 (95) PO TO PO CHANGE OK 1.50 (38).25-20UNC-2B x.62 (16) DP. (2) MOUNTG HOLES 3.88 MAX. (98) 7.75 (197) 3.73 Ø (95) 5.62 (143) TOP OF SP ON ELEMENT OPTIONAL ELECTRIC SWITCH SP ON THREAD= UNF-2B Metric dimensions in ( ). Model No. of filter in photograph is 6P10S. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head & Cap: Case: Weight of -6P: Change Clearance: Up to 20 gpm (75 L/min) f 150 SUS (32 cst) fluids 100 psi (7 bar) 150 psi (10 bar) Contact facty -20 F to 225 F (-29 C to 107 C) Cracking: 30 psi (2 bar) Full Flow: 36 psi (2 bar) Die Cast Aluminum Steel 1.8 lbs. (0.8 kg) 2.50 (65 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm P N/A N/A 37 PZ N/A PZ N/A Collapse Rating: 100 psid (7 bar) Flow Direction: Outside In Nominal Dimensions: 3.75 (95 mm) O.D. x 5.5 (140 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Appropriate Schroeder Media P10, PZ25 PZ25 PZ25 PZ25 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

34 Spin-On Full pted die cast aluminum head f minimum pressure drop. Pipe and SAE straight thread pting. Visual electrical dirt alarms. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 30 psi (2.1 bar) bypass valve. E To Media 100 psi P10 P10 (7 bar) Z Media PZ25 PZ25 Flow Dirt Alarm Seal (See Appendix A f Series Length Part No. Magnet Pting complete list of options) 6 gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 10 gpm (38 L/min) f 6P10SY2 using 200 SUS (44 cst) fluid. Solution: P housing = 2.0 psi [.18 bar] P element = 10 x.17 x ( ) = 2.3 psi P element = [38 x ( ) x (44 32) =.16 bar] P total = = 4.3 psi P element = [ =.34 bar] P10 PZ10 PZ25 P housing f fluids with sp gr = 0.86: P psi sp gr = specific gravity (Omit) = Buna N Flow (L/min) (25) (50) (75) Flow gpm P = 3 4 NPTF S = SAE Straight (SAE-12) P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): P10.17 PZ25.15 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. (0.50) (0.25) P (bar) Y2 = Tri-Col Gauge ES = Electric Switch See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 131

35 Spin-On 50 gpm 190 L/min 100 psi 7 bar.31-18unc-2b x.50 (13) DP. OR M8 x 1.25 x (13) DP. (2) MOUNTG HOLES 1.88 (48) 2.68 (68) 1.34 (34) 5.25 (133) PO TO PO OK CHANGE 2.63 (67) OPTIONAL ELECTRIC SWITCH 3.50 (MAX.) (89) 7M = 9.50 (241) 10M = (333) 5.06 (129) Ø 7M = 6.87 (174) 10M = (261) TOP OF SP-ON ELEMENT SP-ON THREAD= UN-2B Metric dimensions in ( ). Model No. of filter in photograph is 7M10S. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head & Cap: Case: Weight of -7M: Weight of -10M: Change Clearance: Up to 50 gpm (190 L/min) f 150 SUS (32 cst) fluids 100 psi (7 bar) 150 psi (10 bar) Contact facty -20 F to 225 F (-29 C to 107 C) Cracking: 30 psi (2 bar) Full Flow: 48 psi (3 bar) Die Cast Aluminum Steel 4.2 lbs. (1.9 kg) 5.0 lbs. (2.3 kg) 2.50 (65 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO " Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm M N/A N/A 50 M N/A N/A 37 MZ3 <1.0 <1.0 < MZ Collapse Rating: Flow Direction: Nominal Dimensions: 100 psid (7 bar) Outside In 7M: 5.0 (125 mm) O.D. x 7.0 (180 mm) long 10M: 5.0 (125 mm) O.D. x 10.5 (261 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z3, Z10 Z10 Z10 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

36 Spin-On Full pted die cast aluminum head f minimum pressure drop. Pipe, SAE straight, and BSPP pting available. Visual electrical dirt alarms. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 30 psi (2.1 bar) bypass valve. To 100 psi (7 bar) Dirt Alarm Seal (See Appendix A f Series Length Part No. Magnet Pting complete list of options) E M3 M3 See Media M10 M10 See Z MZ3 MZ3 See Media MZ10 MZ10 See Flow 7 10 gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 25 gpm (95 L/min) f 7M3P using 200 SUS (44 cst) fluid. Solution: P housing = 1.0 psi [.08 bar] P element = 25 x.23 x ( ) = 7.7 psi P element = [95 x ( ) x (44 32) =.54 bar] P total = = 8.7 psi P element = [ =.62 bar] M3 M10 MZ3 MZ10 MW MZ3 MZ10 P housing f fluids with sp gr = 0.86: P psi sp gr = specific gravity (Omit) = Buna N V = Viton Flow (L/min) (50) (100) (150) Flow gpm P= NPTF S= SAE Straight (SAE-20) B = ISO 228 G ( BSPP) (B pting supplied with metric mounting holes) P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 7" M3.23 M10.14 MZ3.22 MZ10.17 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. Note: Replacement element part numbers f 7" length begin with M. Replacement element part numbers f 10" length begin with 10M. L = Two 1 8 NPTF inlet and outlet female test pts (0.50) (0.25) P (bar) Y2 = Tri-Col Gauge ES = Electric Switch See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 133

37 Spin-On 60 gpm 230 L/min 150 psi 10 bar 5.50 (140) 2.75 (70).94 (24).94 (24).50-13UNC-2B X.62 (16) DEEP OR M12 x 1.75 x (16) DEEP (2) MOUNTG HOLES 4.50 MAX. (114) 1.25 (32) 2.34 (60) OPTIONAL DI ALARM OR ELECTRIC SWITCH 5.50 (140) 2.75 (70) 7M = 6.88 (175) 10M = (261) 5.06 Ø (129) SP-ON THREAD= UN-2B Metric dimensions in ( ). Model No. of filter in photograph is 7M10SD5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of -7M: Change Clearance: Up to 60 gpm (230 L/min) f 150 SUS (32 cst) fluids 150 psi (10 bar) 250 psi (17 bar) Contact facty -20 F to 225 F (-29 C to 107 C) Cracking: 30 psi (2 bar) Full Flow: 48 psi (3 bar) Cast Iron Steel 8.6 lbs. (3.9 kg) 1.50 (40 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm M N/A N/A 50 M N/A N/A 37 MZ3 <1.0 <1.0 < MZ Collapse Rating: Flow Direction: Nominal Dimensions: 100 psid (7 bar) Outside In 7M: 5.0 (125 mm) O.D. x 7.0 (180 mm) long 10M: 5.0 (125 mm) O.D. x 10.5 (261 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z3, Z10 Z10 Z10 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

38 Spin-On Full pted cast iron head f minimum pressure drop. Pipe, SAE straight, and BSPP pting available. Differential pressure cartridge dirt alarm. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 30 psi (2.1 bar) bypass valve. To 150 psi (10 bar) Dirt Alarm Seal (See Appendix A f Series Length Part No. Material Pting complete list of options) E 7M3 7M3 See Media 7M10 7M10 See Z 7MZ3 7MZ3 See Media 7MZ10 7MZ10 See Flow 7 gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 30 gpm (115 L/min) f 7MZ3D5 using 200 SUS (44 cst) fluid. Solution: P housing = 3.0 psi [.22 bar] P element = 30 x.22 x ( ) = 8.8 psi P element = [115 x ( ) x (44 32) =.63 bar] P total = = 11.8 psi P element = [ =.83 bar] M3 M10 MZ3 MZ10 MW P housing f fluids with sp gr = 0.86: P psi sp gr = specific gravity (Omit) = Buna N V = Viton Flow (L/min) (25) (75) (125) (175) Flow gpm P = NPTF S = SAE Straight (SAE-20) B = ISO 228 G ( BSPP) (B pting supplied with metric mounting holes) P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): M M3.23 M10.14 MZ3.22 MZ10.17 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. 10 MZ3 MZ10 Note: Replacement element part numbers f 7" length begin with M. Replacement element part numbers f 10" length begin with 10M. (0.75) (0.5) (0.25) P (bar) D5 = Cartridge Electric Cartridge: MS5AC/DC/LC Family (See Appendix A) See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 135

39 Return Line 30 gpm 120 L/min 300 psi 20 bar A 4.50 (114) A 4.25 (108) 4.50 MAX. (114) OPTIONAL DI ALARM OR ELECTRIC SWITCH 1.38 (35).88 (22) 1.50 (38).38 (10).38-16UNC-2B x.50 (13) DEEP OR M10 x 1.5 x (13) DEEP (2) MOUNTG HOLES 1A = 9.31 (236) 2A = (359) VIEW A-A 3.50 Ø (89) Metric dimensions in ( ). Model No. of filter in photograph is AZ10SD5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of -1A: Weight of -2A: Change Clearance: Up to 30 gpm (120 L/min) f 150 SUS (32 cst) fluids 300 psi (20 bar) 1200 psi (80 bar) 270 psi (19 bar), per NFPA T F to 225 F (-29 C to 107 C) Cracking: 30 psi (2 bar) Full Flow: 51 psi (4 bar) Anodized Cast Aluminum Steel 5.1 lbs. (2.3 kg) 6.3 lbs. (2.9 kg) 3.50 (90 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm A N/A N/A 16 A N/A N/A 13 AZ1 <1.0 <1.0 <1.0 < AZ3 <1.0 <1.0 < AZ AZ AZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 3.0 (75 mm) O.D. x 4.5 (115 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5 and Z25H.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

40 Return Line Pipe, SAE straight, flange, and BSPP pting available. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 30 psi (2.1 bar) bypass valve. To 300 psi (20 bar) P filter = P housing + P element P housing P element Exercise: Determine P at 20 gpm (75 L/min) f 2AZ3PD using 200 SUS (44 cst) fluid. Solution: P housing = 4.5 psi [.30 bar] P element = 20 x.25 x ( ) = 6.7 psi P element = [75 x ( ) x (44 32) =.47 bar] P total E Media Z Media Flow = = 11.2 psi P element = [ =.77 bar] A3 1A3 2A3 A10 1A10 2A10 A25 1A25 AZ1 1AZ1 2AZ1 AZ3 1AZ3 2AZ3 AZ5 AZ5 AZ10 AZ10 AZ25 AZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (25) (50) (75) (100) Flow gpm sp gr = specific gravity Sizing of elements should be based on element flow infmation provided in the chart above. 1 2 L=Two 1 4 NPTF inlet & outlet female test pts N=No- indicat (Omit) = Buna N H = EPR V = Viton P = 1 NPTF (0.50) (0.25) S= SAE Straight (SAE-16) F = 1 SAE J518 4-Bolt Flange Code 61* B = ISO 228 G-1 (1-11 BSPP) (B pting supplied with metric mounting holes) P (bar) G440 = 1 2 drain on bottom of housing P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 1A 2A A A A AZ AZ AZ AZ AZ If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Dirt Alarm No. of Seal (See Appendix A f Series s Part No. Material Pting complete list of options) A3** A10** A25** AZ1 AZ3 AZ5 AZ10 AZ25 AM10 AM60 **Not available with Dirt Alarm. **Only available with Buna N seals. D = Pointer D5 = Cartridge MS = Cam Operated Electric Switch MS2 = Cam Operated Electric Switch Electric Cartridge: MS5AC/DC/LC Family (See Appendix A) MS15DC = DC Switch (SP) See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 137

41 Return Line 30 gpm 120 L/min 300 psi 20 bar A 4.50 (114) A 4.25 (108) 4.50 MAX. (114) OPTIONAL DI ALARM OR ELECTRIC SWITCH 1.38 (35).88 (22) 1.50 (38) 8T = (359).38 (10).38-16UNC-2B x.50 (13) DEEP OR M10 x 1.5 x (13) DEEP (2) MOUNTG HOLES 3.50 (89) Ø VIEW A-A Metric dimensions in ( ). Model No. of filter in photograph is 8T10SD5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of -8T: Change Clearance: Up to 30 gpm (120 L/min) f 150 SUS (32 cst) fluids 300 psi (20 bar) 1200 psi (80 bar) 270 psi (19 bar), per NFPA T F to 225 F (-29 C to 107 C) Cracking: 50 psi (3 bar) Full Flow: 72 psi (5 bar) Anodized Cast Aluminum Steel 6.7 lbs. (3.0 kg) 3.50 (90 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 8T N/A N/A 39 8T N/A N/A 32 8TZ1 <1.0 <1.0 <1.0 < TZ3 <1.0 <1.0 < TZ TZ TZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 3.1 (80 mm) O.D. x 8.0 (205 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5 and Z25H.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

42 Return Line Meets HF3 automotive standard. Pipe, SAE straight, flange, and BSPP pting available. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 50 psi (3.4 bar) bypass valve. To 300 psi (20 bar) P filter = P housing + P element P housing P element Exercise: Determine P at 15 gpm (57 L/min) f 8T10PD5 using 200 SUS (44 cst) fluid. Solution: P housing = 3.0 psi [.20 bar] P element = 15 x.09 x ( ) = 1.8 psi P element = [57 x ( ) x (44 32) =.12 bar] P total Z Media Flow = = 4.8 psi P element = [ =.32 bar] 8TZ1 8TZ1 See 8TZ3 8TZ3 8TZ5 8TZ5 8TZ10 8TZ10 8TZ25 8TZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (25) (50) (75) (100) Flow gpm sp gr = specific gravity Sizing of elements should be based on element flow infmation provided in the chart above. 8 L=Two 1 4 NPTF inlet & outlet female test pts N=No- indicat (Omit) = Buna N H = EPR V = Viton P = 1 NPTF (0.50) (0.25) P (bar) S= SAE Straight (SAE-16) F = 1 SAE J518 4-Bolt Flange Code 61* B = ISO 228 G-1 (1-11 BSPP) (B pting supplied with metric mounting holes) G440 = 1 2 drain on bottom of housing P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 8T3.25 8T T TZ1.37 8TZ3.21 8TZ5.13 8TZ TZ25.08 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Part No. Dirt Alarm Seal (See Appendix A f Series Length Media Material Pting complete list of options) T3** T10** T25 TZ1 TZ3 TZ5 TZ10 TZ25 **Bolt thread depth.63 (16 mm). Not available with Dirt Alarm. **Only available with Buna N seals. D5 = Cartridge Electric Cartridge: MS5AC/DC/LC Family (See Appendix A) See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 139

43 Return Line 100 gpm 380 L/min 300 psi 20 bar 6.25 (159) 1.68 TYP (43) 6.25 (159).87 TYP (22) 3.00 (76) OPTIONAL DI ALARM OR ELECTRIC SWITCH.50 MTG. HOLE (13) SURFACE 1.25 (32) 4.50 MAX. (114) 5.50 (140).31-18UNC-2B x.60 (15) M. DEPTH OR M8 x 1.25 x (15) DP. (4) MOUNTG HOLES 1K = (333) 2K = (568) 3K = (810) 4.68 Ø (119) Metric dimensions in ( ). Model No. of filter in photograph is 1K10PD5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of -1K: Weight of -2K: Weight of -3K: Change Clearance: Up to 100 gpm (380 L/min) f 150 SUS (32 cst) fluids 300 psi (20 bar) 1000 psi (70 bar) 290 psi (20 bar), per NFPA T F to 225 F (-29 C to 107 C) Cracking: 30 psi (2 bar) Full Flow: 51 psi (4 bar) Die Cast Aluminum Steel 10.5 lbs. (4.8 kg) 14.2 lbs. (6.4 kg) 18.5 lbs. (8.4 kg) 1.50 (40 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm K N/A N/A 54 K N/A N/A 44 KZ1 <1.0 <1.0 <1.0 < KZ3 <1.0 <1.0 < KZ KZ KZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 4.0 (100 mm) O.D. x 9.0 (230 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) Media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z Media with EPR Seals, K3H and K10H E Media Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

44 Return Line Meets HF4 automotive standard. Pipe, SAE straight, flange, and BSPP pting available. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 30 psi (2.1 bar) bypass valve. To 300 psi (20 bar) E Media Z Media Flow K3 1K3 2K3 3K3 K10 1K10 2K10 3K10 K25 1K25 2K25 KZ1 1KZ1 2KZ1 3KZ1 KZ3 1KZ3 2KZ3 KZ5 1KZ5 2KZ5 KZ10 KZ25 1KZ10 1KZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 60 gpm (225 L/min) f 2KZ5SD5 using 200 SUS (44 cst) fluid. Solution: P housing = 3.5 psi [.24 bar] P element = 60 x.04 x ( ) = 3.2 psi P element = [225 x ( ) x (44 32) =.23 bar] P total = = 6.7 psi P element = [ =.47 bar] P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (50) (150) (250) (350) Flow gpm sp gr = specific gravity P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 1K 2K 3K K K K KZ KZ KZ KZ KZ If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. Dirt Alarm No. of Seal (See Appendix A f Series s Part No. Material Pting complete list of options) K3 K10 K25** KZ1 KZ3 KZ5 KZ10 KZ25 KW KM10 KM25 KM60 L= Two 1 4 NPTF inlet & outlet female test pts N= No- indicat (Omit) = Buna N H = EPR*** V = Viton*** W = Buna N*** ***Bolt thread depth.63 (16 mm). ***Not available with EPR seals. ***When H, W, & V seals are dered, all aluminum filter parts are anodized. P= NPTF (0.50) (0.25) S= SAE Straight (SAE-24) F= SAE J518 4-Bolt Flange Code 61* B = ISO 228 G ( BSPP) (B pting supplied with metric mounting holes) P (bar) Double and triple stacking of K-size elements can be replaced by single KK and 27K elements, respectively. G426 = 3 4 drain on bottom of housing G440 = 1 2 drain on bottom of housing D = Pointer MS = Cam Operated Electric Switch MS2 = Cam Operated Electric Switch D5 = Cartridge Electric Cartridge: MS5AC/DC/LC Family (See Appendix A) MS15DC = DC Switch (SP) See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 141

45 W Return Line (Water Service) 100 gpm 380 L/min 300 psi 20 bar TYP (159) (43) 5.50 (140) 6.25 (159).87 TYP (22) 3.00 (76) OPTIONAL DI ALARM OR ELECTRIC SWITCH MTG. HOLE SURFACE.50 (13) 1.25 (32) 4.50 MAX. (114).31-18UNC-2B x.60 (15) M. DEPTH OR M8 x 1.25 x (15) DP. (4) MOUNTG HOLES 1K = (333) 2K = (568) 3K = (810) 4.68 Ø (119) Metric dimensions in ( ). Model No. of filter in photograph is W1KM25PD5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of W-1K: Weight of W-2K: Weight of W-3K: Change Clearance: Up to 100 gpm (380 L/min) f 150 SUS (32 cst) fluids 300 psi (20 bar) 1000 psi (70 bar) 290 psi (20 bar), per NFPA T F to 225 F (-29 C to 107 C) Cracking: 30 psi (2 bar) Full Flow: 51 psi (4 bar) Anodized Die Cast Aluminum Steel with Internal Protective Coating 11.0 lbs. (5.0 kg) 14.7 lbs. (6.7 kg) 18.1 lbs. (8.2 kg) 1.50 (40 mm) Perfmance Nominal Rating Metal Mesh (micron) KM10 10 KM25 25 KM60 60 KM KM Collapse Rating: Flow Direction: Nominal Dimensions: 150 psid (10 bar) Outside In 3.5 (90 mm) O.D. x 9.25 (235 mm) long Fluid Compatibility Type Fluid Water Appropriate Schroeder Media All Metal (M) elements Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

46 Return Line (Water Service) F use in water systems. Furnished with cleanable metal elements. selections are predicated on the use of water and a 30 psi Pressure Series Part No. (2.1 bar) bypass valve. To 300 psi (20 bar) M Media Flow KM10 KM25 KM60 KM150 KM260 1KM10 1KM25 1KM60 1KM150 1KM260 gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 50 gpm (190 L/min) f W1KM10P using water. Solution: P housing = 2.6 psi [.14 bar] P element = 50 x.08 = 4.0 psi P element = [190 x ( ) =.28 bar] P total = = 6.6 psi P element = [ =.42 bar] W P housing f water: P psi Flow (L/min) (50) (150) (250) (350) Flow gpm P element = flow x element P fact x viscosity fact El. P facts: KM10.08 KM25.06 KM60.01 KM KM If wking in units of bars & L/min, divide above fact by Sizing of elements should be based on element flow infmation provided in the chart above. Dirt Alarm No. of Seal (See Appendix A f Series s Part No. Material Pting complete list of options) W KM10 KM25 KM60 KM150 KM260 *Bolt thread depth.63 (16 mm). L= Two 1 4 NPTF inlet & outlet female test pts (Omit) = Buna N P= NPTF (0.50) (0.25) S= SAE Straight (SAE-24) F= SAE J518 4-Bolt Flange Code 61* B = ISO 228 G ( BSPP) (B pting supplied with metric mounting holes) P (bar) G426 = 3 4 drain on bottom of housing G440 = 1 2 drain on bottom of housing D = Pointer MS = Cam Operated Electric Switch MS2 = Cam Operated Electric Switch D5 = Cartridge Electric Cartridge: MS5AC/DC/LC Family (See Appendix A) See Appendix B f additional infmation on these options and instructions on how to der. W Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 143

47 Return Line 100 gpm 380 L/min 300 psi 20 bar A 5.62 (143) 6.25 (159) A 1.50 MAX. (38) 1.88 (48) 1.88 OPTIONAL DI ALARM OR ELECTRIC SWITCH.38-16UNC-2B x.50(13) DP. OR M10 x 1.5 x (13) DP. (2) MOUNTG HOLES (44) (51).62 (16) 1K = (360) 2K = (602) 3K = (837) 4.69 Ø (119) VIEW A-A Metric dimensions in ( ). Model No. of filter in photograph is 1K10PD. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of -1K: Weight of -2K: Weight of -3K: Change Clearance: Up to 100 gpm (380 L/min) f 150 SUS (32 cst) fluids 300 psi (20 bar) 1000 psi (70 bar) 250 psi (17 bar), per NFPA T F to 225 F (-29 C to 107 C) Cracking: 25 psi (2 bar) Full Flow: 60 psi (4 bar) Anodized Cast Aluminum Steel 13.7 lbs. (6.2 kg) 17.5 lbs. (7.9 kg) 22.3 lbs. (10.1 kg) 2.00 (55 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm K N/A N/A 54 K N/A N/A 44 KZ1 <1.0 <1.0 <1.0 < KZ3 <1.0 <1.0 < KZ KZ KZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 4.0 (100 mm) O.D. x 9.0 (230 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) Media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z Media with EPR Seals, K3H and K10H E Media Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

48 Return Line Meets HF4 automotive standard. Pipe, SAE straight, flange, and BSPP pting available. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 25 psi (1.7 bar) bypass valve. To 300 psi (20 bar) P filter = P housing + P element P housing P element Exercise: Determine P at 40 gpm (150 L/min) f 3K10SD5 using 200 SUS (44 cst) fluid. Solution: P housing = 2.5 psi [.18 bar] P element = 40 x.03 x ( ) = 1.6 psi P element = [150 x ( ) x (44 32) =.11 bar] P total E Media Z Media Flow = = 4.1 psi P element = [ =.29 bar] K3 1K3 2K3 3K3 K10 1K10 2K10 3K10 K25 1K25 2K25 KZ1 1KZ1 2KZ1 3KZ1 KZ3 1KZ3 2KZ3 3KZ3 KZ5 1KZ5 2KZ5 KZ10 KZ25 P housing f fluids with sp gr = 0.86: P psi Flow (L/min) 12 (50) (150) (250) (350) 10 (0.75) 8 (0.50) 6 4 (0.25) Flow gpm sp gr = specific gravity 1KZ10 1KZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. Sizing of elements should be based on element flow infmation provided in the chart above L= Two 1 4 NPTF inlet & outlet female test pts (Omit) = Buna N H = EPR V = Viton P= NPTF P (bar) S= SAE Straight (SAE-24) F= SAE J518 4-Bolt Flange Code 61* B = ISO 228 G ( BSPP) (B pting supplied with metric mounting holes) G426 = 3 4 drain on bottom of housing G440 = 1 2 drain on bottom of housing P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 1K 2K 3K K K K KZ KZ KZ KZ KZ If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Dirt Alarm No. of Seal (See Appendix A f Series s Part No. Material Pting complete list of options) K3 K10 K25** KZ1 KZ3 KZ5 KZ10 KZ25 KW KM10 KM25 KM60 **Bolt thread depth.63 (16 mm). ** Not available with EPR seals. D = Pointer MS = Electric Cam Operated F 2 pting, See contact Double facty. and triple stacking of K-size elements can be replaced by single KK and 27K elements, respectively. See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 145

49 Return Line With 2" Pts NEW PRODUCT 120 gpm 455 L/min 300 psi 20 bar A 5.62 (143) A 1.50 MAX. (38) 1.88 (48) 1.88 OPTIONAL DI ALARM OR ELECTRIC SWITCH 6.25 (159).38-16UNC-2B x.50(13) DP. OR M10 x 1.5 x (13) DP. (2) MOUNTG HOLES (44) (51).62 (16) 18L= (603) 4.69 Ø (119) VIEW A-A Metric dimensions in ( ). Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Available Pting: Weight of -18L: Change Clearance: Up to 120 gpm (455 L/min) f 150 SUS (32 cst) fluids 300 psi (20 bar) 1000 psi (70 bar) 250 psi (17 bar), per NFPA T F to 225 F (-29 C to 107 C) Cracking: 30 psi (2.1 bar) Full Flow: 60 psi (4.1 bar) Anodized Cast Aluminum Steel 2" NPTF, SAE Straight 17.5 lbs. (7.9 kg) 2.00 (55 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 18L N/A N/A L N/A N/A 88 18LZ1 <1.0 <1.0 <1.0 < LZ3 <1.0 <1.0 < LZ LZ LZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 4.0 (100 mm) O.D. x 18.5 (470 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol 146 Appropriate Schroeder Media All Paper (E) and Synthetic (Z) Media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z Media with EPR Seals Z3H.5, Z5H.5, Z10H.5 and Z25H.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and 20.

50 NEW PRODUCT Return Line With 2" Pts Pipe, SAE straight, and BSPP pting available. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 30 psi (2.1 bar) bypass valve. 18LZ1 18LZ1 To 300 psi (20 bar) P filter = P housing + P element P housing P element Exercise: Determine P at 40 gpm (150 L/min) f 8LZ10S32D5 using 200 SUS (44 cst) fluid. Solution: P housing = 1.0 psi [.07 bar] P element = 40 x.03 x ( ) = 1.6 psi P element = [150 x ( ) x (44 32) =.11 bar] P total Z Media Flow 18LZ3 18LZ5 18LZ10 18LZ25 = = 2.6 psi P element = [ =.18 bar] -2" P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (50) (150) (250) (350) Flow gpm sp gr = specific gravity 18LZ3 18LZ5 18LZ10 18LZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. Sizing of elements should be based on element flow infmation provided in the chart above. 18" L= Two 1 4 NPTF inlet & outlet female test pts (Omit) = Buna N H = EPR V = Viton P32 = 2 NPTF 120 (0.75) (0.50) (0.25) P (bar) S32 = SAE Straight (SAE-32) B32= ISO 228 G-2 (2-11 BSPP) (B pting supplied with metric mounting holes) G426 = 3 4 drain on bottom of housing G440 = 1 2 drain on bottom of housing P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 18LZ LZ LZ LZ LZ25.02 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Part No. Dirt Alarm Seal (See Appendix A f Series Length Media Material Pting complete list of options) L3 L10 LZ1 LZ3 LZ5 LZ10 LZ25 Note: 2" pts are available with K-size elements f up to 100 gpm. Contact facty. D = Pointer MS = Electric Cam Operated See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 147

51 M Top-Pted Return Line 200 gpm 760 L/min 300 psi 20 bar 1.50 MAX. (38) 2.25 (57) 2K = (370) 4K = (611) 6K = (846) MANIFOLD OPTIONAL DI ALARM OR ELECTRIC SWITCH MANIFOLD.50-13UNC-2B x 1.00 (25) DEEP (4) MOUNTG HOLES (FROM BOTTOM) 3.00 (76) (297) 6.00 (152) 4.69 (119) Ø 8.50 (216) 4.25 (108) (327) Metric dimensions in ( ). Model No. of filter in photograph is M4K10PD. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of M-2K: Weight of M-4K: Weight of M-6K: Change Clearance: Up to 200 gpm (760 L/min) f 150 SUS (32 cst) fluids 300 psi (20 bar) 1000 psi (70 bar) 250 psi (17 bar), per NFPA T F to 225 F (-29 C to 107 C) Cracking: 25 psi (2 bar) Full Flow: 60 psi (4 bar) Anodized Cast Aluminum Steel 44.0 lbs. (20.0 kg) 50.0 lbs. (23.0 kg) 58.0 lbs. (26.0 kg) 2.00 (55 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm K N/A N/A 54 K N/A N/A 44 KZ1 <1.0 <1.0 <1.0 < KZ3 <1.0 <1.0 < KZ KZ KZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 4.0 (100 mm) O.D. x 9.0 (230 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol 148 Appropriate Schroeder Media All Paper (E) and Synthetic (Z) Media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z Media with EPR Seals, K3H and K10H E Media Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and 20.

52 Top-Pted Return Line Meets HF4 automotive standard. Pipe and flange pting available. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 25 psi (1.7 bar) bypass valve. To 300 psi (20 bar) E Media Z Media Flow K3 4K3 6K3 K10 4K10 6K10 K25 P filter = P housing + P element P housing P element M P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (200) (400) (600) Flow gpm sp gr = specific gravity PO TO PO 4K25 KZ1 4KZ1 6KZ1 KZ3 2KZ3 3KZ3 4KZ3 KZ5 2KZ5 4KZ5 6KZ5 KZ10 2KZ10 4KZ10 KZ25 2KZ25 4KZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. The P housing curve labeled Sizing is the pressure drop between the inlet and outlet areas of the filter s bypass valve and should be used f filter sizing. The Pt to Pt P takes into consideration any manifolds and/ special valving. This pressure drop can be significantly higher due to these additional flow constrictions. Although this P does not affect the perfmance of the filter, it should be considered f overall system design. ELEMENT SIZG Sizing of elements should be based on element flow infmation provided in the chart above. Dirt Alarm No. of Seal (See Appendix A f Series s Part No. Material Pting complete list of options) M K3 K10 K25** KZ1 KZ3 KZ5 KZ10 KZ25 KM60 KM150 **Not available with EPR seals. L= Two 1 4 NPTF inlet & outlet female test pts (Omit) = Buna N H = EPR V = Viton P= NPTF (2.00) (1.50) (1.00) (0.50) P (bar) F = SAE J518 4-Bolt Flange Code 61 G426 = 3 4 drain on bottom of housing G440 = 1 2 drain on bottom of housing P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 2K 4K 6K K K K KZ KZ KZ KZ KZ If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). D = Pointer MS = Electric Cam Operated See Appendix B f additional infmation on these options and instructions on how to der. M Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 149

53 S U.S. Patent # Medium Pressure 25 gpm 100 L/min 1400 psi 100 bar 3.50 (89).94 (24) 3.50 (89) PO TO PO.81 (21) 1.62 (41) 6R = 9.38 (238) OPTIONAL DI ALARM OR ELECTRIC SWITCH.94 (24) C POS.84 (21).31-18UNC-2B x.50 (13) DEEP OR M8 x 1.25 x (13) DEEP (2) MOUNTG HOLES 2.62 (67) Ø 4.50 MAX. (114) Metric dimensions in ( ). Model No. of filter in photograph is S6RZ10S12D5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of S-6R: Change Clearance: Up to 25 gpm (100 L/min) f 150 SUS (32 cst) fluids 1400 psi (100 bar) 4000 psi (276 bar) 750 psi (52 bar) per NFPA T2.6.1-R F to 225 F (-29 C to 107 C) Cracking: 40 psi (2.8 bar) Full Flow: 55 psi (3.8 bar) Die Cast Aluminum Steel 3.0 lbs. (1.4 kg) 2.75 (70 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 6R N/A N/A 5 6R N/A N/A 6 6RZ1 <1.0 <1.0 <1.0 < RZ3 <1.0 <1.0 < RZ RZ RZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 2.0 (50 mm) O.D. x 6.0 (150 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5 and Z25H.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

54 U.S. Patent # Unique dirt tolerant rolled thread design. Quick and easy cartridge element changeouts. P filter = P housing + P element P housing P element Exercise: Determine P at 15 gpm (57 L/min) f S6R3P12D5 using 200 SUS (44 cst) fluid. Solution: P housing = 5.0 psi [.37 bar] P element = 15 x.45 x ( ) = 9 psi P element = [57 x ( ) x (44 32) =.64 bar] P total = = 14.0 psi P element = [ = 1.01 bar] S P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (25) (50) (75) (95) (1.0) Flow gpm sp gr = specific gravity Smaller, compact version of. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 40 psi (2.8 bar) bypass valve. To 1400 psi (100 bar) E 6R3 6R3 See Media 6R10 6R10 See 6RZ1 6RZ1 See Z 6RZ3 6RZ3 See Media 6RZ5 6RZ5 See 6RZ10 6RZ10 See 6RZ25 6RZ25 Flow gpm (L/min) Shown above are the elements most commonly used in this housing. Sizing of elements should be based on element flow infmation provided in the chart above. 6 (Omit) = Buna N H = EPR* V = Viton* P12 = 3 4 NPTF (0.75) (0.5) (0.25) P (bar) S12 = SAE Straight (SAE-12) B12 = ISO 228 G- 3 4 ( BSPP) (B12 pting supplied with metric mounting holes) P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 6R3.45 6R RZ RZ3.55 6RZ5.50 6RZ RZ25.14 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Dirt Alarm Part No. Seal (See Appendix A f Series Length Media Material Pting complete list of options) S R3** R10** RZ1 RZ3 RZ5 RZ10 RZ25 **Aluminum parts are anodized. **Only available with Buna N seals. L=Two 1 4 NPTF inlet & outlet female test pts Medium Pressure D5 = Cartridge Electric Cartridge: MS5AC/DC/LC Family MS15DC = DC Switch (SP) See Appendix B f additional infmation on these options and instructions on how to der. S Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 151

55 S U.S. Patent # Medium Pressure NEW PRODUCT 25 gpm 100 L/min 1400 psi 100 bar 3.50 (89).94 (24) 3.50 (89) PO TO PO.81 (21) 1.62 (41) 6R = 9.38 (238) OPTIONAL DI ALARM OR ELECTRIC SWITCH.94 (24) C POS.84 (21).31-18UNC-2B x.50 (13) DEEP OR M8 x 1.25 x (13) DEEP (2) MOUNTG HOLES 2.62 (67) Ø 4.50 MAX. (114) Metric dimensions in ( ). Model No. of filter in photograph is S6GRZ10S12D5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of S-6R: Change Clearance: Up to 25 gpm (100 L/min) f 150 SUS (32 cst) fluids 1400 psi (100 bar) 4000 psi (276 bar) 750 psi (52 bar) per NFPA T2.6.1-R F to 200 F (-29 C to 93 C) Cracking: 40 psi (2.8 bar) Full Flow: 55 psi (3.8 bar) Die Cast Aluminum Steel 3.0 lbs. (1.4 kg) 2.75 (70 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 6GRZ1 <1.0 <1.0 <1.0 < GRZ3 <1.0 <1.0 < GRZ GRZ GRZ Collapse Rating: 125 psid (8.6 bar) Flow Direction: Outside In Nominal Dimensions: 2.0 (50 mm) O.D. x 6.0 (150 mm) long Fluid Compatibility Type Fluid Appropriate Schroeder Media Petroleum Based Fluids All 6GR Esafe elements Note: Contact facty f use with other fluids. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

56 NEW PRODUCT Medium Pressure S U.S. Patent # Unique dirt tolerant rolled thread design. Smaller, compact version of Esafe TM. Esafe elements contain no metal and are fully recyclable can be incinerated, crushed shredded. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 40 psi (2.8 bar) bypass valve. To 1400 psi (100 bar) P filter = P housing + P element P housing P element Exercise: Determine P at 15 gpm (57 L/min) f S6GRZ25P12D5 using 200 SUS (44 cst) fluid. Solution: P housing = 5.0 psi [.37 bar] P element = 15 x.24 x ( ) = 4.8 psi P element = [57 x ( ) x (44 32) =.34 bar] P total Z Media Flow 6GRZ1 6GRZ3 6GRZ5 6GRZ10 6GRZ25 = = 9.8 psi P element = [ =.71 bar] S P housing f fluids with sp gr=0.86: P psi GRZ1 6GRZ3 Flow (L/min) (25) (50) (75) (95) (1.0) Flow gpm sp gr = specific gravity 6GRZ5 6GRZ10 6GRZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. Sizing of elements should be based on element flow infmation provided in the chart above. S 6 GRZ1 GRZ3 GRZ5 GRZ10 GRZ25 **Aluminum parts are anodized. (Omit) = Buna N H = EPR* V = Viton* P12 = 3 4 NPTF (0.75) (0.5) (0.25) P (bar) S12 = SAE Straight (SAE-12) B12 = ISO 228 G- 3 4 ( BSPP) (B12 pting supplied with metric mounting holes) P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 6GRZ GRZ3.78 6GRZ5.60 6GRZ GRZ25.24 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Dirt Alarm Part No. Seal (See Appendix A f Series Length Media Material Pting complete list of options) L=Two 1 4 NPTF inlet & outlet female test pts D5 = Cartridge Electric Cartridge: MS5AC/DC/LC Family MS15DC = DC Switch (SP) See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 153

57 T U.S. Patent # Medium Pressure 70 gpm 270 L/min 800 psi 55 bar.31-18unc-2b x.50 (13) DP. OR M8 x 1.25 x (13) DP. (4) MOUNTG HOLES 4.18 (106) 4.75 (121) 1.38 (35).69 (17.5) OPTIONAL DI ALARM OR ELECTRIC SWITCH 1.50 (38) 4.50 MAX. (114) 1.94 (49) 3.88 (98) 8T = (310) 13T = (430) 16T = (529) 3.50 (89) Ø Metric dimensions in ( ). Model No. of filter in photograph is T8TZ10F16D5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of T-8T: Change Clearance: Up to 70 gpm (270 L/min) f 150 SUS (32 cst) fluids f P20, S20, & B20 pting Up to 50 gpm (190 L/min) f 150 SUS (32 cst) fluids f P16, S16, F16, F20 & B16 pting 800 psi (55 bar) 2400 psi (165 bar) 415 psi (29 bar), per NFPA T2.6.1-R F to 225 F (-29 C to 107 C) Cracking: 50 psi (3 bar) f all pting Full Flow: 45 psi (3 bar) f P20 & S20 pting Full Flow: 68 psi (5 bar) f P16, S16, F16 & F20 pting Die Cast Aluminum Steel 6.7 lbs. (3.0 kg) 2.75 (70 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 8T N/A N/A 39 8T N/A N/A 32 8TZ1 <1.0 <1.0 <1.0 < TZ3 <1.0 <1.0 < TZ TZ TZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 3.1 (80 mm) O.D. x 8.0 (205 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol 154 Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5 and Z25H.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and 20.

58 U.S. Patent # Unique dirt tolerant rolled thread design. Meets HF3 automotive standard. Quick and easy element changeouts. To 800 psi (55 bar) P filter = P housing + P element P housing P element Exercise: Determine P at 40 gpm (150 L/min) f T8TZ10S16D5 using 200 SUS (44 cst) fluid. Solution: P housing = 5.5 psi [.40 bar] P element = 40 x.11 x ( ) = 5.9 psi P element = [150 x ( ) x (44 32) =.41 bar] P total = = 11.4 psi P element = [ =.81 bar] T P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (50) (100) (150) (200) (250) SIZE 16 POG Flow gpm sp gr = specific gravity Medium Pressure selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 40 psi (2.8 bar) bypass valve. SIZE 20 POG Sizing of elements should be based on element flow infmation provided in the chart above. T E 8T3 8T3 See Contact Facty f H3 Option Media 8T10 8T10 8TZ1 8TZ1 See Contact Facty f HF3 Option 8TZ3 8TZ3 See Contact Facty f HF3 Option Z Media 8TZ5 8TZ5 8TZ10 8TZ10 8TZ25 8TZ25 Flow T3* T10* TZ1 TZ3 TZ5 TZ10 TZ25 TW **Only available with Buna N seals. **Aluminum parts are anodized. (Omit) = Buna N H = EPR** V = Viton** P16 = 1 NPTF P20 = NPTF (0.75) (0.50) (0.25) P (bar) S16 = SAE Straight (SAE-16) S20 = SAE Straight (SAE-20) F16 = 1 SAE J518 4-Bolt Flange Code 61 F20 = SAE J518 4-Bolt Flange Code 61 B16 = ISO 228 G-1 (1-11 BSPP) B20 = ISO 228 G ( BSPP) (B16 & B20 pting supplied with metric mounting holes) P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 8T3.25 8T T TZ1.37 8TZ3.21 8TZ5.13 8TZ TZ25.08 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Dirt Alarm Part No. Seal (See Appendix A f Series Length Media Material Pting complete list of options) L=Two 1 4 NPTF inlet & outlet female test pts gpm (L/min) Shown above are the elements most commonly used in this housing. D5 = Cartridge See Contact Facty f HF3 Option Electric Cartridge: MS5AC/DC/LC Family See Contact Facty f HF3 Option requires size 20 pting See Appendix B f additional infmation on these options and instructions on how to der. T Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 155

59 U.S. Patent # gpm 270 L/min 800 psi 55 bar Medium Pressure.31-18UNC-2B x.50 (13) DP. OR M8 x 1.25 x (13) DP. (4) MOUNTG HOLES 4.18 (106) 4.75 (121) 1.38 (35).69 (17.5) OPTIONAL DI ALARM OR ELECTRIC SWITCH 1.50 (38) 4.50 MAX. (114) 1.94 (49) 3.88 (98) 9V = (344) 14V = (471) 3.50 (89) Ø Metric dimensions in ( ). Model No. of filter in photograph is 9VZ10S16D5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of -9V: Weight of -14V: Change Clearance: Up to 70 gpm (270 L/min) f 150 SUS (32 cst) fluids f P20, S20, & B20 pting Up to 50 gpm (190 L/min) f 150 SUS (32 cst) fluids f P16, S16, F16, F20 & B16 pting 800 psi (55 bar) 2400 psi (165 bar) 415 psi (29 bar), per NFPA T2.6.1-R F to 225 F (-29 C to 107 C) Cracking: 40 psi (2.8 bar) f all pting Full Flow: 57 psi (3.9 bar) f P20 & S20 pting Full Flow: 75 psi (5.2 bar) f P16, S16, F16 & F20 pting Die Cast Aluminum Steel 6.7 lbs. (3.0 kg) 8.0 lbs. (3.6 kg) 9V & 14V: 2.75 (70 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 9V3/14V N/A N/A 25/38 9V10/14V N/A N/A 12/25 9VZ1/14VZ1 <1.0 <1.0 <1.0 < /102 9VZ3/14VZ3 <1.0 <1.0 < /105 9VZ5/14VZ /83 9VZ10/14VZ /104 9VZ25/14VZ /94 Collapse Rating: 150 psid (10 bar) 500 psid (34.5 bar) f hydrostatic high crush (9V5Z10 element) version Flow Direction: Outside In Nominal Dimensions: 9V: 3.0 (75 mm) O.D. x 9.5 (240 mm) long 14V: 3.0 (75 mm) O.D. x 14.5 (370 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5 and Z25H.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

60 U.S. Patent # Unique dirt tolerant rolled thread design. Durable, lightweight, compact design. Quick and easy element changeouts. To 800 psi (55 bar) P filter = P housing + P element P housing P element Exercise: Determine P at 40 gpm (150 L/min) f 9VZ5S16D5 using 200 SUS (44 cst) fluid. Solution: P housing = 5.5 psi [.35 bar] P element = 40 x.13 x ( ) = 6.9 psi P element = [150 x ( ) x (44 32) =.49 bar] P total = = 12.4 psi P element = [ =.84 bar] P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (50) (150) (250) SIZE 16 POG Flow gpm sp gr = specific gravity SIZE 20 POG Sizing of elements should be based on element flow infmation provided in the chart above V3* V10* VZ1 VZ3 VZ5 VZ10 VZ25 VW N 9 V5Z10 **Only available with Buna N seals. **Aluminum parts are anodized. (Omit) = Buna N H = EPR** V = Viton** Medium Pressure selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 40 psi (2.8 bar) bypass valve. E Media 9V3 & 14V3 9V3 14V3 Contact Facty 9V10 & 14V10 9V10 14V10 Contact Facty 9VZ1 & 14VZ1 9VZ1 14VZ1 Contact Facty 9VZ3 & 14VZ3 9VZ3 14VZ3 Contact Facty Z Media 9VZ5 & 14VZ5 9VZ5 14VZ5 9VZ10 & 14VZ10 9VZ10 & 14VZ10 9VZ25 & 14VZ25 9VZ25 & 14VZ25 Flow (0.75) (0.50) (0.25) P (bar) P16 = 1 NPTF P20 = NPTF S16 = SAE Straight (SAE-16) S20 = SAE Straight (SAE-20) F16 = 1 SAE J518 4-Bolt Flange Code 61 F20 = SAE J518 4-Bolt Flange Code 61 B16 = ISO 228 G-1 (1-11 BSPP) B20 = ISO 228 G ( BSPP) (B16 & B20 pting supplied with metric mounting holes) P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 9V 14V 9V V3.19 9V V VZ VZ1.21 9VZ VZ3.17 9VZ VZ5.09 9VZ VZ VZ VZ25.05 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Dirt Alarm Part No. Seal (See Appendix A f Series Length Media Material Pting complete list of options) L=Two 1 4 NPTF inlet & outlet female test pts gpm (L/min) Shown above are the elements most commonly used in this housing. requires size 20 pting D5 = Cartridge Electric Cartridge: MS5AC/DC/LC Family MS15DC = DC Switch (SP) See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 157

61 U.S. Patent # Medium Pressure NEW PRODUCT 70 gpm 270 L/min 800 psi 55 bar.31-18unc-2b x.50 (13) DP. OR M8 x 1.25 x (13) DP. (4) MOUNTG HOLES 4.18 (106) 4.75 (121) 1.38 (35).69 (17.5) OPTIONAL DI ALARM OR ELECTRIC SWITCH 1.50 (38) 4.50 MAX. (114) 1.94 (49) 3.88 (98) 9V = (344) 14V = (471) 3.50 (89) Ø Metric dimensions in ( ). Model No. of filter in photograph is 9GVZ10S16D5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of -9V: Change Clearance: Up to 70 gpm (270 L/min) f 150 SUS (32 cst) fluids f P20, S20, & B20 pting Up to 50 gpm (190 L/min) f 150 SUS (32 cst) fluids f P16, S16, F16, F20 & B16 pting 800 psi (55 bar) 2400 psi (165 bar) 415 psi (29 bar), per NFPA T2.6.1-R F to 200 F (-29 C to 93 C) Cracking: 40 psi (2.8 bar) f all pting Full Flow: 57 psi (3.9 bar) f P20 & S20 pting Full Flow: 75 psi (5.2 bar) f P16, S16, F16 & F20 pting Die Cast Aluminum Steel 6.7 lbs. (3.0 kg) 2.75 (70 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 9GVZ1 <1.0 <1.0 <1.0 < GVZ3 <1.0 <1.0 < GVZ GVZ GVZ Collapse Rating: 125 psid (8.6 bar) Flow Direction: Outside In Nominal Dimensions: 9V: 3.0 (75 mm) O.D. x 9.5 (240 mm) long Fluid Compatibility Type Fluid Appropriate Schroeder Media Petroleum Based Fluids All 9GV Esafe elements Note: Contact facty f use with other fluids. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

62 NEW PRODUCT Medium Pressure U.S. Patent # Unique dirt tolerant rolled thread design. Esafe TM elements contain no metal and are fully recyclable can be incinerated, crushed shredded. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 40 psi (2.8 bar) bypass valve. To 800 psi (55 bar) P filter = P housing + P element P housing P element Exercise: Determine P at 40 gpm (150 L/min) f 9GVZ25S16D5 using 200 SUS (44 cst) fluid. Solution: P housing = 5.5 psi [.35 bar] P element = 40 x.09 x ( ) = 4.8 psi P element = [150 x ( ) x (44 32) =.34 bar] P total Z Media Flow = = 10.3 psi P element = [ =.69 bar] 9GVZ1 9GVZ3 9GVZ5 9GVZ10 9GVZ25 P psi GVZ1 9GVZ3 9GVZ5 9GVZ10 Flow (L/min) (50) (150) (250) SIZE 16 POG Flow gpm sp gr = specific gravity 9GVZ25 gpm (L/min) Shown above are the elements most commonly used in this housing. SIZE 20 POG Sizing of elements should be based on element flow infmation provided in the chart above. 9 GVZ1 GVZ3 GVZ5 GVZ10 GVZ25 *Aluminum parts are anodized. P housing f fluids with sp gr=0.86: (Omit) = Buna N H = EPR* V = Viton* (0.75) (0.50) (0.25) P (bar) P16 = 1 NPTF P20 = NPTF S16 = SAE Straight (SAE-16) S20 = SAE Straight (SAE-20) F16 = 1 SAE J518 4-Bolt Flange Code 61 F20 = SAE J518 4-Bolt Flange Code 61 B16 = ISO 228 G-1 (1-11 BSPP) B20 = ISO 228 G ( BSPP) (B16 & B20 pting supplied with metric mounting holes) requires size 20 pting P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 9V 9GVZ1.48 9GVZ3.26 9GVZ5.22 9GVZ GVZ25.09 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Dirt Alarm Part No. Seal (See Appendix A f Series Length Media Material Pting complete list of options) L=Two 1 4 NPTF inlet & outlet female test pts D5 = Cartridge Electric Cartridge: MS5AC/DC/LC Family MS15DC = DC Switch (SP) See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 159

63 W Medium Pressure (Water Service) NEW PRODUCT 70 gpm 270 L/min 800 psi 55 bar.31-18unc-2b x.50 (13) DP. OR M8 x 1.25 x (13) DP. (4) MOUNTG HOLES 4.18 (106) 4.75 (121) 1.38 (35).69 (17.5) OPTIONAL DI ALARM OR ELECTRIC SWITCH 1.50 (38) 4.50 MAX. (114) 1.94 (49) 3.88 (98) 9V = (344) 14V = (471) 3.50 (89) Ø Metric dimensions in ( ). Model No. of filter in photograph is W9VM150S16D5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of W-9V: Change Clearance: Up to 70 gpm (270 L/min) f 150 SUS (32 cst) fluids 800 psi (55 bar) 2400 psi (165 bar) 415 psi (29 bar), per NFPA T2.6.1-R F to 225 F (-29 C to 107 C) Cracking: 40 psi (2.8 bar) Full Flow: 57 psi (3.9 bar) Anodized Cast Aluminum Steel with protective coating 6.25 lbs. (2.8 kg) 2.75 (70 mm) Perfmance Nominal Rating Metal Mesh (micron) 9VM VM VMX VMX Collapse Rating: Flow Direction: Nominal Dimensions: 150 psid (10 bar) Outside In 3.0 (75 mm) O.D. x 9.5 (240 mm) long Fluid Compatibility Type Fluid Water Appropriate Schroeder Media All Metal (M) elements F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

64 NEW PRODUCT Medium Pressure (Water Service) W U.S. Patent # Unique dirt tolerant rolled thread design. Durable, lightweight, compact design. Quick and easy element changeouts. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 40 psi (2.8 bar) bypass valve. To 800 psi (55 bar) M Media Flow 9VM150 9VM260 9VMX150 9VMX260 9VM150 9VM260 9VMX150 9VMX260 gpm (L/min) Shown above are the elements most commonly used in this housing. P filter = P housing + P element P housing P element Exercise: Determine P at 50 gpm (190 L/min) f W9VM150P20 using water. Solution: P housing = 7.0 psi [.48 bar] P element = 50 x.03 = 1.5 psi P element = [190 x ( ) =.10 bar] P total = = 8.5 psi P element = [ =.58 bar] W P housing f water: P psi Flow (L/min) (50) (150) (250) Flow gpm sp gr = specific gravity Sizing of elements should be based on element flow infmation provided in the chart above. W 9 SKB Housings L Pressure Drop Accessies f Tank- s and Viscosity Filler Strainer Assemblies Magnetic Suction Separats Model Number W 2" M S S T W Other Available M Options 4 Filtration Carts WN (Non- Bypass) 9 VM150 VM260 VMX150 VMX260 **Only available with Buna N seals. **Aluminum parts are anodized. (Omit) = Buna N H = EPR V = Viton P20 = NPTF (0.75) (0.50) (0.25) P (bar) S20 = SAE Straight P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 9VM VM VMX VMX If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Dirt Alarm Part No. Seal (See Appendix A f Series Length Media Material Pting complete list of options) L=Two 1 4 NPTF inlet & outlet female test pts D5 = Cartridge Electric Cartridge: MS5AC = AC only MS5DC = DC only MS5LC = AC & DC (Low current application) See Appendix B f additional infmation on these options and instructions on how to der. Features 161

65 Medium Pressure 100 gpm 380 L/min 800 psi 55 bar 5.62 (143) 6.25 (159) PO TO PO.38-16UNC-2B x.50 (13) DP. OR M10 x 1.5 x (13) DP. (2) MOUNTG HOLES 1.75 (44) 2.00 (51) 1.88 (48).62 (16) OPTIONAL DI ALARM OR ELECTRIC SWITCH 4.50 MAX (114) 1K = (360) 4.69 (119) Ø Metric dimensions in ( ). Model No. of filter in photograph is 1KZ10SD5. Housing Specifications Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Head: Case: Weight of -1K: Change Clearance: Up to 100 gpm (380 L/min) f 150 SUS (32 cst) fluids 800 psi (55 bar) 2600 psi (179 bar) 500 psi (35 bar), per NFPA T F to 225 F (-29 C to 107 C) Cracking: 40 psi (2.8 bar) Full Flow: 61 psi (4.2 bar) Grey Cast Iron Steel 23.2 lbs. (10.5 kg) 2.00 (51 mm) Perfmance Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm K N/A N/A 54 K N/A N/A 44 KZ1 <1.0 <1.0 <1.0 < KZ3 <1.0 <1.0 < KZ KZ KZ Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 4.0 (100 mm) O.D. x 9.0 (230 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) Media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z Media with EPR Seals, K3H and K10H E Media Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. 162 F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and 20.

66 Medium Pressure Meets HF4 automotive standard. Cast iron head construction. Pipe, SAE straight, flange, and BSPP pting available. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 40 psi (2.8 bar) bypass valve. K3 1K3 housing uses only one K size element. E Media K10 1K10 K25 1K25 To KZ1 1KZ1 800 psi (55 bar) KZ3 1KZ3 Z Media KZ5 1KZ5 KZ10 1KZ10 KZ25 1KZ25 P filter = P housing + P element P housing P element Exercise: Determine P at 50 gpm (189 L/min) f 1KZ10P24D5 using 200 SUS (44 cst) fluid. Solution: P housing = 3.0 psi [.20 bar] P element = 50 x.05 x ( ) = 3.3 psi P element = [189 x ( ) x (44 32) =.24 bar] P total Flow = = 6.3 psi P element = [ =.44 bar] gpm (L/min) Shown above are the elements most commonly used in this housing. P housing f fluids with sp gr = 0.86: Flow gpm sp gr = specific gravity housing uses only one K size element. P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): K3.25 K10.09 K25.02 KZ1.20 KZ3.10 KZ5.08 KZ10.05 KZ25.04 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. *Not available with EPR seals. 1 K3 K10 K25* KZ1 KZ3 KZ5 KZ10 KZ25 KW L= Two 1 4 NPTF inlet & outlet female test pts P psi (Omit) = Buna N W= Buna N H = EPR V = Viton Flow (L/min) (100) (200) Dirt Alarm Seal (See Appendix A f Series Length Part No. Material Pting complete list of options) (300) P24 = NPTF P32 = 2 NPTF (0.75) (0.50) (0.25) S24 = SAE Straight (SAE-24) S32 = SAE Straight (SAE-32) F24 = SAE J518 Split Flange Code 61 B24 = ISO 228 G ( BSPP) (B24 pting supplied with metric mounting holes) P (bar) D = Pointer MS = Electric Cam Operated D5 = Cartridge Electric Cartridge: MS5AC/DC/LC Family See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 163

67 Base-Pted 250 gpm 950 L/min 500 psi 35 bar 39Q = (1353) 16Q = (797) 7.00 Ø (178) 9.75 (248) 4.88 (124) 2.25 (57) (267) SAE 4-BOLT FLG. POS (272) PIPE & R.THD. POS 9.12 (232) 2.25 (57).56 (14) Ø THRU (2) MOUNTG HOLES DRA PLUG OPTIONAL DI ALARM OR ELECTRIC SWITCH 4.50 MAX. (114) US 3.00 (76) D DRA PLUG Housing Specifications Perfmance Metric dimensions in ( ). Model No. of filter in photograph is 39QZ10P3230. Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Base & Cap: Case: Weight of -16Q: Weight of -39Q: Change Clearance: Up to 250 gpm (950 L/min) f 150 SUS (32 cst) fluids 500 psi (35 bar) Contact facty not designed f cyclic pressure applications -20 F to 225 F (-29 C to 107 C) Cracking: 15 psi (1 bar), 30 psi (2 bar), 50 psi (3.5 bar) specify in model no. Full Flow: 69 psi (5 bar) Aluminum Aluminum 86.0 lbs. (39.0 kg) lbs. (47.6 kg) 16Q (380 mm) 39Q (940 mm) Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 16QZ1/16QPMLZ1 <1.0 <1.0 <1.0 < /307 16QZ3/16QPMLZ3 <1.0 <1.0 < /315 16QZ5/16QPMLZ /264 16QZ10/16QPMLZ /330 16QZ25/16QPMLZ /299 39Q10/39QPML N/A N/A 475/814 39QZ1/39QPMLZ1 <1.0 <1.0 <1.0 < / QZ3/39QPMLZ3 <1.0 <1.0 < / QZ5/39QPMLZ /895 39QZ10/39QPMLZ / QZ25/39QPMLZ /1299 Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 16Q: 6.0 (150 mm) O.D. x (430 mm) long 16QPML: 6.0 (150 mm) O.D. x 16.0 (405 mm) long 39Q: 6.0 (150 mm) O.D. x 38.7 (985 mm) long 39QPML: 6.0 (150 mm) O.D. x 37.8 (960 mm) long Fluid Compatibility Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

68 Base-Pted All aluminum filter f non-cyclic lubrication and return line applications. No tools required to service element. changeout from top minimizes oil spillage. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 30 psi (2.1 bar) bypass valve. To 500 psi (35 bar) E Media 16Q25 16Q25 Consult Facty f 39" Paper Elem. 16 & 39QZ1 16QZ1 39QZ1 16 & 39QZ3 16QZ3 39QZ3 16 & 39QZ5 16QZ5 39QZ5 16 & 39QZ10 16QZ10 & 39QZ10 Z 16 & 39QZ25 16QZ25 & 39QZ25 Media 16 & 39QPMLZ1 16QPMLZ1 39QPMLZ1 16 & 39QPMLZ3 16QPMLZ3 39QPMLZ3 16 & 39QPMLZ5 16QPMLZ5 39QPMLZ5 16 & 39QPMLZ10 16QPMLZ10 & 39QPMLZ10 16 & 39QPMLZ25 16QPMLZ25 & 39QPMLZ25 Flow gpm (L/min) Shown above are the elements most commonly used in this housing. Note: Max. flow may be lower if using a 15 psi bypass valve. See Pressure Drop below. P filter = P housing + P element P housing P element Exercise: Determine P at 150 gpm (570 L/min) f 16QPMLZ3S3230D5 using 200 SUS (44 cst) fluid. Solution: P housing = 2.5 psi [.18 bar] P element = 150 x.05 x ( ) = 10.0 psi P element = [570 x ( ) x (44 32) =.71 bar] P total = = 12.5 psi P element = [ =.89 bar] P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (200) (500) sp gr = specific gravity Sizing of elements should be based on element flow infmation provided in the chart above. Housing Dirt Alarm Seal Bypass (See Appendix A f Series Part No. Material Pting Setting complete list of options) 16Q10 16Q25 16QZ1/16QPMLZ1 16QZ3/16QPMLZ3 16QZ5/16QPMLZ5 16QZ10/16QPMLZ10 16QZ25/16QPMLZ25 16QW 39Q10 39Q25 39QZ1/39QPMLZ1 39QZ3/39QPMLZ3 39QZ5/39QPMLZ5 39QZ10/39QPMLZ10 39QZ25/39QPMLZ25 X=Blocked bypass valve B = Buna N H = EPR* V = Viton* W = Buna N* (800) Flow gpm P32 = 2 NPTF P40 = NPTF P48 = 3 NPTF S32 = SAE Straight (SAE-32) F32 = 2 SAE J518 4-Bolt Flange Code 61 F40 = SAE J518 4-Bolt Flange Code 61 F48 = 3 SAE J518 4-Bolt Flange Code 61 39QW All elements are supplied with Viton Seals. Note: All blocks are machined with two 1 4 NPTF inlet and outlet female test pts. *When H, V, W seals are dered all aluminum filter parts are anodized. W=Anodized option (0.50) (0.25) P (bar) (Omit) = 30 psi cracking 15 = 15 psi cracking 50 = 50 psi cracking P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 16QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ25.01 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). (Omit) = None D5 = Cartridge D5C = Cartridge in Cap Electric Cartridge: MS5AC/DC/LC Family DPG = Differential Pressure Gauge See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 165

69 M Base-Pted 300 gpm 1135 L/min 500 psi 35 bar 7.00 (178) Ø 9.12 (232) (533) 9.12 (232) 39Q = (1353) 16Q = (797) 9.75 (248) 4.88 (124) 2.25 (57) 2.25 (57) 4.50 MAX. (114) DRA PLUG OPTIONAL DI ALARM OR ELECTRIC SWITCH.56 (14) Ø THRU (4) MOUNTG HOLES 3.00 (76) D D Housing Specifications Perfmance Fluid Compatibility Metric dimensions in ( ). Model No. of filter in photograph is M39QS1P32. Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Base & Cap: Case: Weight of M-16Q: Weight of M-39Q: Change Clearance: Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Up to 300 gpm (1135 L/min) f 150 SUS (32 cst) fluids 500 psi (35 bar) Contact facty not designed f cyclic pressure applications -20 F to 225 F (-29 C to 107 C) Cracking: 15 psi (1 bar), 30 psi (2 bar), 50 psi (3.5 bar) specify in model no. Full Flow: 55 psi (4 bar) Aluminum Aluminum DRA PLUG lbs. (64.4 kg) lbs. (82.1 kg) 16Q (380 mm) 39Q (940 mm) Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 16QZ1/16QPMLZ1 <1.0 <1.0 <1.0 < /307 16QZ3/16QPMLZ3 <1.0 <1.0 < /315 16QZ5/16QPMLZ /264 16QZ10/16QPMLZ /330 16QZ25/16QPMLZ /299 39Q10/39QPML N/A N/A 475/814 39QZ1/39QPMLZ1 <1.0 <1.0 <1.0 < / QZ3/39QPMLZ3 <1.0 <1.0 < / QZ5/39QPMLZ /895 39QZ10/39QPMLZ / QZ25/39QPMLZ /1299 Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 16Q: 6.0 (150 mm) O.D. x (430 mm) long 16QPML: 6.0 (150 mm) O.D. x 16.0 (405 mm) long 39Q: 6.0 (150 mm) O.D. x 38.7 (985 mm) long 39QPML: 6.0 (150 mm) O.D. x 37.8 (960 mm) long Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

70 Base-Pted M All aluminum dual filter f non-cyclic lubrication and return line applications. No tools required to service element. changeout from top minimizes oil spillage. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 30 psi (2.1 bar) bypass valve. E Media 16 & 39Q25 16Q25 & 39Q25 16 & 39QZ1 16QZ1 39QZ1 16 & 39QZ3 16QZ3 39QZ3 16 & 39QZ5 16QZ5 To 16 & 39QZ10 16QZ10 & 39QZ10 Z 500 psi 16 & 39QZ25 16QZ25 & 39QZ25 Media (35 bar) 16 & 39QPMLZ1 16QPMLZ1 39QPMLZ1 16 & 39QPMLZ3 16QPMLZ3 39QPMLZ3 16 & 39QPMLZ5 16QPMLZ5 39QPMLZ5 16 & 39QPMLZ10 16QPMLZ10 & 39QPMLZ10 16 & 39QPMLZ25 16QPMLZ25 & 39QPMLZ25 Shown above are the elements most commonly used in this housing. Note: Max. flow may be lower if using a 15 psi bypass valve. See Pressure Drop below. P filter = P housing + P element P housing P element Exercise: Determine P at 250 gpm (950 L/min) f M39QPMLZ3S3230D5 using 200 SUS (44 cst) fluid. Solution: P housing = 4.0 psi [.30 bar] P element = 250 x.01 x ( ) = 6.7 psi 2 = 1.7 psi P element = [950 x ( ) x (44 32) =.47 bar 2 =.12 bar] P total = = 5.7 psi P element = [ =.42 bar] M P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (200) (500) (800) (1000) Flow gpm sp gr = specific gravity Sizing of elements should be based on element flow infmation provided in the chart above. M Flow 16Q10 16Q25 16QZ1/16QPMLZ1 16QZ3/16QPMLZ3 16QZ5/16QPMLZ5 16QZ10/16QPMLZ10 16QZ25/16QPMLZ25 16QW 39Q10 39Q25 39QZ1/39QPMLZ1 39QZ3/39QPMLZ3 39QZ5/39QPMLZ5 39QZ10/39QPMLZ10 39QZ25/39QPMLZ25 39QW All elements are supplied with Viton Seals. Note: All M blocks are machined with two 1 4 NPTF inlet and outlet female test pts. *When H seals are dered all aluminum filter parts are anodized. X=Blocked bypass valve gpm (L/min) B = Buna N H = EPR* V = Viton P32 = 2 NPTF P40 = NPTF P48 = 3 NPTF S32 = SAE Straight (SAE-32) F32 = 2 SAE J518 4-Bolt Flange Code 61 F40 = SAE J518 4-Bolt Flange Code 61 F48 = 3 SAE J518 4-Bolt Flange Code 61 W=Anodized option (0.50) (0.25) P (bar) (Omit) = 30 psi cracking 15 = 15 psi cracking 50 = 50 psi cracking P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 16QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ25.01 If wking in units of bars & L/min, divide above fact by Viscosity fact: Divide viscosity by 150 SUS (32 cst). Housing Dirt Alarm Seal Bypass (See Appendix A f Series Part No. Material Pting Setting complete list of options) (Omit) = None D5 = Cartridge D5C = Cartridge in Cap Electric Cartridge: MS5AC/DC/LC Family DPG = Differential Pressure Gauge See Appendix B f additional infmation on these options and instructions on how to der. Features SKB Housings L Accessies f Tank- Pressure s Drop Filler Strainer Assemblies and Viscosity Magnetic Suction Separats Model Number W 2" M S S T W Other Available M Options 4 Filtration Carts 167

71 Duplex Base-Pted 250 gpm 950 L/min 200 psi 15 bar 39Q = (1353) 16Q = (797) 7.00 (178) Ø 39Q = (1398) 16Q = (842) (689) PO TO PO (646) SAE 4-BOLT FLG. PO A A OPTIONAL BASE CHANNEL OPTIONAL DI ALARM OR ELECTRIC SWITCH (495) (991) 4.50 MAX. (114) Housing Specifications Perfmance Fluid Compatibility Metric dimensions in ( ). Model No. of filter in photograph is 39QS7F40. Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Base & Cap: Case: Weight of -16Q: Weight of -39Q: Change Clearance: Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Up to 250 gpm (950 L/min) f 150 SUS (32 cst) fluids 200 psi (15 bar) Contact facty not designed f cyclic pressure applications -20 F to 225 F (-29 C to 107 C) Cracking: 15 psi (1 bar), 30 psi (2 bar), 50 psi (3.5 bar) specify in model no. Full Flow: 69 psi (5 bar) Aluminum Aluminum VIEW A-A lbs. (231.8 kg) lbs. (249.5 kg) 16Q (380 mm) 39Q (940 mm) Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 16QZ1/16QPMLZ1 <1.0 <1.0 <1.0 < /307 16QZ3/16QPMLZ3 <1.0 <1.0 < /315 16QZ5/16QPMLZ /264 16QZ10/16QPMLZ /330 16QZ25/16QPMLZ /299 39Q10/39QPML N/A N/A 475/814 39QZ1/39QPMLZ1 <1.0 <1.0 <1.0 < / QZ3/39QPMLZ3 <1.0 <1.0 < / QZ5/39QPMLZ /895 39QZ10/39QPMLZ / QZ25/39QPMLZ /1299 Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 16Q: 6.0 (150 mm) O.D. x (430 mm) long 16QPML: 6.0 (150 mm) O.D. x 16.0 (405 mm) long 39Q: 6.0 (150 mm) O.D. x 38.7 (985 mm) long 39QPML: 6.0 (150 mm) O.D. x 37.8 (960 mm) long Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and

72 Duplex Base-Pted All aluminum duplex filter f non-cyclic lubrication and return line applications. No tools required to service element. changeout from top minimizes oil spillage. selections are predicated on the use of 150 SUS (32 cst) Pressure Series Part No. petroleum based fluid and a 30 psi (2.1 bar) bypass valve. To 200 psi (15 bar) P filter = P housing + P element P housing P element E Media 16Q25 16Q25 Consult Facty f 39" Paper Elem. 16 & 39QZ1 16QZ1 39QZ1 16 & 39QZ3 16QZ3 39QZ3 16 & 39QZ5 16QZ5 39QZ5 16 & 39QZ10 16QZ10 & 39QZ10 Z 16 & 39QZ25 16QZ25 & 39QZ25 Media 16 & 39QPMLZ1 16QPMLZ1 39QPMLZ1 16 & 39QPMLZ3 16QPMLZ3 39QPMLZ3 16 & 39QPMLZ5 16QPMLZ5 39QPMLZ5 16 & 39QPMLZ10 16QPMLZ10 & 39QPMLZ10 16 & 39QPMLZ25 16QPMLZ25 & 39QPMLZ25 Flow 16Q10 16Q25 16QZ1/16QPMLZ1 16QZ3/16QPMLZ3 16QZ5/16QPMLZ5 16QZ10/16QPMLZ10 16QZ25/16QPMLZ25 16QW 39Q10 39Q25 39QZ1/39QPMLZ1 39QZ3/39QPMLZ3 39QZ5/39QPMLZ5 39QZ10/39QPMLZ10 39QZ25/39QPMLZ25 39QW All elements are supplied with Viton Seals. Note: All blocks are machined with two 1 4 NPTF inlet and outlet female test pts. *When H seals are dered all aluminum filter parts are anodized. X=Blocked bypass valve gpm (L/min) Shown above are the elements most commonly used in this housing. Note: Max. flow may be lower if using a 15 psi bypass valve. See Pressure Drop below. The P housing curve labeled Sizing is the pressure drop between the inlet and outlet areas of the filter s bypass valve and should be used f filter sizing. The Pt to Pt P takes into consideration any manifolds and/ special valving. This pressure drop can be significantly higher due to these additional flow constrictions. Although this P does not affect the perfmance of the filter, it should be considered f overall system design. B = Buna N H = EPR* V = Viton P housing f fluids with sp gr = 0.86: P psi Flow (L/min) (200) (500) Flow gpm P32 = 2 NPTF P40 = NPTF P48 = 3 NPTF PO TO PO S32 = SAE Straight (SAE-32) F32 = 2 SAE J518 4-Bolt Flange Code 61 F40 = SAE J518 4-Bolt Flange Code 61 F48 = 3 SAE J518 4-Bolt Flange Code 61 W=Anodized option (800) ELEMENT SIZG (1.00) (0.50) P (bar) (Omit) = 30 psi cracking 15 = 15 psi cracking 50 = 50 psi cracking P element = flow x element P fact x viscosity fact El. P 150 SUS (32 cst): 16QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ QPMLZ QZ25.01 If wking in units of bars & L/min, divide above fact by Viscosity fact: sp gr = specific gravity Divide viscosity by 150 SUS (32 cst). Sizing of elements should be based on element flow infmation provided in the chart above. Housing Dirt Alarm Seal Bypass (See Appendix A f Series Part No. Material Pting Setting complete list of options) (Omit) = None D5 = Cartridge D5C = Cartridge in Cap Electric Cartridge: MS5AC/DC/LC Family DPG = Differential Pressure Gauge See Appendix B f additional infmation on these options and instructions on how to der. Features Pressure Drop and Viscosity Model Number Other Available Options SKB Housings L Accessies f Tank- s Filler Strainer Assemblies Magnetic Suction Separats W 2" M S S T W M 4 Filtration Carts 169

73 4 Duplex Base-Pted 300 gpm 1135 L/min 200 psi 15 bar 39Q = (1353) 16Q = (797) 7.00 (178) Ø 39Q = (1398) 16Q = (842) (956) PO TO PO (913) SAE 4-BOLT FLG. PO A A OPTIONAL DI ALARM OR ELECTRIC SWITCH OPTIONAL BASE CHANNEL 4.50 MAX. (114) (495) (991) VIEW A-A Housing Specifications Perfmance Fluid Compatibility Metric dimensions in ( ). Model No. of filter in photograph is 439QS7F40. Flow Rating: Max. Operating Pressure: Min. Yield Pressure: Rated Fatigue Pressure: Temp. Range: Bypass Setting: Pting Base & Cap: Case: Weight of 4-16Q: Weight of 4-39Q: Change Clearance: Type Fluid Petroleum Based Fluids High Water Content Invert Emulsions Water Glycols Phosphate Esters Skydrol Up to 300 gpm (1135 L/min) f 150 SUS (32 cst) fluids 200 psi (15 bar) Contact facty not designed f cyclic pressure applications -20 F to 225 F (-29 C to 107 C) Cracking: 15 psi (1 bar), 30 psi (2 bar), 50 psi (3.5 bar) specify in model no. Full Flow: 55 psi (4 bar) Aluminum Aluminum lbs. (317.5 kg) lbs. (351.5 kg) 16Q (380 mm) 39Q (940 mm) Absolute Rating Per ISO 4572/NFPA T Abs. Rating wrt ISO Using automated particle counter (APC) calibrated per ISO 4402 Using APC calibrated per ISO Dirt Holding ß x 75 ß x 100 ß x 200 ß x (c) 200 ß x (c) 1000 Capacity gm 16QZ1/16QPMLZ1 <1.0 <1.0 <1.0 < /307 16QZ3/16QPMLZ3 <1.0 <1.0 < /315 16QZ5/16QPMLZ /264 16QZ10/16QPMLZ /330 16QZ25/16QPMLZ /299 39Q10/39QPML N/A N/A 475/814 39QZ1/39QPMLZ1 <1.0 <1.0 <1.0 < / QZ3/39QPMLZ3 <1.0 <1.0 < / QZ5/39QPMLZ /895 39QZ10/39QPMLZ / QZ25/39QPMLZ /1299 Collapse Rating: 150 psid (10 bar) Flow Direction: Outside In Nominal Dimensions: 16Q: 6.0 (150 mm) O.D. x (430 mm) long 16QPML: 6.0 (150 mm) O.D. x 16.0 (405 mm) long 39Q: 6.0 (150 mm) O.D. x 38.7 (985 mm) long 39QPML: 6.0 (150 mm) O.D. x 37.8 (960 mm) long Appropriate Schroeder Media All Paper (E) and Synthetic (Z) media Z1, Z3, Z5, Z10, Z25 Z10, Z25 Z3, Z5, Z10, Z25 All Z media with EPR Seals Z3H.5, Z5H.5, Z10H.5, Z25H.5 and WH.5 Note: Contact facty regarding use of E Media in High Water Content, Invert Emulsion and Water Glycol Applications. F me infmation, refer to Fluid Compatibility: Fire Resistant Fluids, pages 19 and