INPINGO LPP0049 USER INSTRUCTIONS. Code Downloaded from lyon.co.uk UI_LPP0049_17286

Transcription

1 USER INSTRUCTIONS INPINGO Code LPP0049 lyon.co.uk/user-instructions For more detailed user information and to download a PDF copy of these instructions follow the link above or scan the QR code with your smart phone Lyon Equipment Limited Units 3-7, Tebay Business Park, Old Tebay, Penrith, Cumbria, United Kingdom, CA10 3SS Tel: +44 (0) info@lyon.co.uk Web: lyon.co.uk Lyon Equipment UI_LPP0049_17286

2 Quality Assurance Quality management system assessed and certified as meeting the requirements of ISO WARNING Practical training in the use of ground anchor systems is essential before use. Please contact Lyon Equipment if you require training. This information must be read and kept in conjunction with the Lyon General User Instructions supplied with this product, the instructions for the Lyon Ground Anchor Stake. Always wear eye, ear and hand protection when using the INPINGO. Keep feet clear of the Ground Anchor Stake and the INPINGO during use. Maintain a suitable exclusion zone around the work area. Use - installation The INPINGO is intended to be used to drive in and remove Lyon Ground Anchor Stakes only. (LPP0006 and MCA0031). Using the T-slot for access, whilst holding the INPINGO at an angle, place the long end of the INPINGO fully over the head of the Ground Anchor Stake (see Figure 1), once over the head of the stake, re-align the INPINGO with the stake and lower the INPINGO down so that the hammer plate is in contact with the top of the stake (see Figure 2a). Ground Anchor Stake driving Raise and lower the INPINGO until the INPINGO is flush with the surface of the ground (see Figure 2b). Remove the INPINGO. Repeat the process using the short end of the INPINGO (see Figure 2c and 2d). The Ground Anchor Stake is now at the suggested minimum insertion depth. Remove the INPINGO and continue assembly of the ground anchor system. a b c d Figure 2 Figure 1 2

3 Ground Anchor Stake removal To remove the Ground Anchor Stake, reverse the procedure above, but use the T-slot collar as the striking surface on bottom of the head of the stake. Use the inertia of the INPINGO to raise the Ground Anchor Stake rather than pulling the stake out of the ground. Inspection INPINGO should be subject to: Pre-use checks Thorough inspections every 6 months recommended Interim inspections (as appropriate) Check for any signs of wear, corrosion, deformity, sharp edges, cracks or other defects. Sharp edges and burrs may be removed with emery cloth. Check the welds to ensure there are no cracks. The checks should be undertaken in good light. Any item showing any defect should be withdrawn from service immediately. It is recommended that the INPINGO is marked with the date of the next or last inspection. Chemicals Avoid all contact with chemical reagents that could affect the performance of the Ground Stake Linking Straps or other items of equipment that may be used with the ground anchor system, e.g. acids, caustic substances and oxidising agents. If the INPINGO comes into contact with any chemicals, remove it from service and contact Lyon Equipment for advice. Materials The INPINGO is made from powder coated carbon steel. Obsolescence The INPINGO has a theoretically infinite lifetime subject to inspection. Marking Marking, if required, can be made on the label with an indelible laundry marker. Markings LPP0049 End of document. Manufacturer s logo Refer to user instructions Wear hearing protection Wear eye protection Wear hand protection Product code 3

4 Purchase date Lyon Product Inspection Record Year of manufacture Date of first use Product Product code Certificate of conformity number description Individual serial number Length if applicable Manufacturer Address Other relevant information Lyon Equipment Ltd. Unit 3-7 Tebay Business Park Tel. +44 (0) Old Tebay Fax. +44 (0) Penrith CA10 3SS lyon.co.uk UK Record of inspection and repair Date Comments Name and signature of competent inspector Next due date All user instructions supplied with this product must be kept as part of the product inspection record EN 4

5 General user instructions Lyon Equipment Limited Units 3-7, Tebay Business Park, Old Tebay, Penrith, Cumbria, United Kingdom, CA10 3SS Tel: +44 (0) Web: lyon.co.uk Lyon Equipment lyon.co.uk/user-instructions For more detailed user information and to download a PDF copy of these instructions follow the link above or scan the QR code with your smart phone UI_GENSCA6_13233

6 WARNING Make sure that you have read and understood these instructions before using this equipment. These user instructions are to be read and kept along with any other user information provided. Activities at height are hazardous and may lead to injury or death. It is the user s responsibility, at all times, to ensure that they understand the correct use of any equipment supplied by or through Lyon Equipment, use it only for the purposes for which it is designed, and practice proper safety procedures including having a rescue plan in case of emergency. This product must not be used outside its limitations, or for any purpose other than those described in the user instructions. Misuses forbidden in these instructions are examples only; many other misuses may exist which could lead to injury or death. Please note, the information in these user instructions is not exhaustive, and is not a substitute for comprehensive instruction and training by a competent person. Lyon Equipment is not responsible for any consequences, whether direct, indirect or accidental, resulting from the use of its products. If you are unsure about the correct use of this product, please contact us. Who can use this equipment This equipment should only be used by trained, competent and responsible persons, or the user should be under the direct supervision of a trained, competent and responsible person. Activities at height should not be undertaken by persons affected by alcohol or drug dependence, diabetes, epilepsy, fits, blackouts, fear of heights, vertigo / dizziness / difficulty with balance, heart disease / chest pain, high or low blood pressure, impaired limb function, obesity, psychiatric illness, musculoskeletal issues, e.g. a bad back. General instructions for use Equipment must be checked before each use, to ensure it is serviceable and operates correctly. Checks should also be carried out during use. In addition, a thorough inspection by a competent inspector should be carried out in strict accordance with these user instructions, and a record kept of these inspections. This product may be used with any compatible item of Personal Protective Equipment (PPE) which conforms to the European Union Directive 89/686/EEC, keeping in mind the limitations of each item in the safety chain. It should be noted that a full body harness is the only type of harness which may be used in a fall arrest system. The anchor device or anchor point is of primary importance and should be unquestionably reliable. It should be strong enough to withstand the 2

7 foreseeable maximum load that could be applied e.g. in the event of a fall. When selecting an anchor, the anticipated directions of loading and potential loads should be taken into account. Anchors should be selected and positioned to allow work to be carried out in such a way as to minimise the potential for a fall and potential fall distance, for example by keeping the anchor point / device above the user. Anchors should not have sharp or rough edges which could damage equipment (use edge protection if necessary). On each occasion of use, verify the free space required beneath the user in order to avoid an impact. Always try to place protection so that any fall will be stopped before the user hits the ground or any other obstruction. Remember to allow for rope stretch and slippage in the belay device or rope ascender / descender. In a fall arrest situation, the user must be protected from dynamic forces of greater than 6 kn in the event of a fall, e.g. by use of a fall arrest system incorporating an EN 355 energy absorber. Maintaining your equipment Wash in clean water not exceeding 30 C with pure soap and rinse in clean cold water. Do not use chemical products, solvents or detergents these should be regarded as harmful. that any contaminated equipment should be withdrawn from use and disposed of in a suitable manner. Equipment must be clean and dry before storing. Always allow to dry naturally, away from direct heat. Equipment should be stored in a cool, dry, well-ventilated area, away from excessive heat, high humidity, sharp edges, corrosives, sunlight or other sources of ultraviolet light (UV) and other possible causes of damage. During transport, this product should be protected from abrasion, mechanical damage, chemical contamination, UV and heat. Textiles Always keep textile items at temperatures between -30 C and +50 C. Metal items Always keep metal items at temperatures between -20 C and +60 C. No alterations, additions or repairs may be made to this product without the manufacturer s prior written consent; if done, the repair must be carried out by a competent person for repair authorised by Lyon Equipment to make the repair, and in accordance with specified procedures. These instructions must be strictly adhered to. Due to the difficulties in effectively disinfecting equipment, we recommend 3

8 Inspection A thorough inspection should be carried out at least every 6 months by a competent inspector in accordance with these user instructions. A record of these checks should be kept with the product along with these user instructions. In addition, interim inspections should be carried out where products are used intensively, or in particularly harsh environments where damage is more likely to occur, or where legislation or the type of equipment make it necessary. Pre-use and thorough inspections are essential because the user s level of protection depends on the continuing correct performance of this product. PPE (Personal Protective Equipment) inspection training is available from Lyon Equipment. Lifetime, and when to withdraw your equipment from use Withdraw your equipment from use if any one of the following applies: It shows sign of wear and tear / damage that may affect performance Markings on the product are no longer legible You suspect it may have been exposed to chemical contamination or extreme temperatures It fails a periodic examination It has been used to arrest a fall or has been excessively loaded It is more than 10 years after the date of manufacture (textile items or items with textile components). Metal items have a potentially indefinite lifespan if stored correctly. If you have any reason to doubt that it is safe to use. It is the responsibility of the competent inspector to decide whether the equipment should be put back into use, or permanently withdrawn from use. Equipment permanently withdrawn from use must be destroyed, and should be recycled where facilities exist. Certain environmental elements will considerably accelerate wear: salt, sand, dust, snow, ice, moisture, chemicals, sunlight (UV radiation) list not exhaustive. Warning: the safe working life of this product may be as short as its first use in extreme circumstances. If in doubt, do not hesitate to scrap this product. Guarantee In the event of any defect in materials or workmanship please return the product to the dealer, distributor or manufacturer within 3 years of purchase for inspection. We will replace or repair as required. This guarantee does not cover normal wear and tear or accidental damage. 4

9 Note to resellers If the product is re-sold outside the UK and Eire, but within the EU, the reseller is responsible for providing instructions for use, maintenance, periodic examination and for repair in the language of the country in which the product is to be used. If you require the Intrastat commodity code / customs tariff code or NATO stock number (where applicable) for this product, please contact us via lyon.co.uk Inspection records A record must be kept for each component, subsystem and system, including name and contact details of the manufacturer or supplier, product description, serial number, year of manufacture, date of purchase, date of first use, any other relevant information, and history of periodic examinations and repairs, the name and signature of the competent inspector and the next due date for inspection. An example of a suitable equipment record is shown on this user instruction and can also be downloaded at lyon.co.uk Local jurisdiction may dictate that extra information be recorded in the inspection record check your country s legal requirements. Some products may have features which need special monitoring during periodic inspections, e.g. wear indicators, in which case this information should also be recorded on the inspection record. 5

10 This page deliberately left blank 6

11 Explanation of symbols Refer to user instructions Permitted use Caution Danger of death Telephone number Anchor point Rope diameter Cable SWL SWL 250kg (Safe Working Load) 7

12 Purchase date Lyon Product Inspection Record Year of manufacture Date of first use Product Product code Certificate of conformity number description Individual serial number Length if applicable Address Other relevant information Manufacturer Tel. +44 (0) Fax. +44 (0) lyon.co.uk Lyon Equipment Ltd. Unit 3-7 Tebay Business Park Old Tebay Penrith CA10 3SS UK Record of inspection and repair Date Comments Name and signature of competent inspector Next due date All user instructions supplied with this product must be kept as part of the product inspection record EN