TANDEM plus BLUMOTION 563H/563. installation instructions

Transcription

1 56H/56. installation instructions inside Full extension concealed runners Basic components ocking devices New side adjustment New rear side adjustment otate side adjustment left or right equally on both locking devices. Drawer front moves in the same direction as rotation. After front side adjustment is made with the locking devices, rotate the rear side adjustment left or right to re-align the back of the box with the front. Drawer back moves in the same direction as rotation. unners ear attachment options Height adjustment Press up on adjustment tab Push towards back of 0 otate the tilt adjustment lever on the rear of each runner to lift the back of the and tilt the top of the front forward. front Tilt adjustment Maximum (/8") rise of front (tool-free) Maximum 5 (/6") rise of back (tool-free) NOTE: Height and tilt adjustments available with all combinations of locking devices and runners 0 New depth adjustable locking device Depth adjustment on runner ocking device TANDEM 56 runners feature elongated holes that allow ±4.5 (/6") depth adjustment T5.90.PS with side, height and depth adjustment Turning the adjustment screw allows for up to a +.5 (") out adjustment Maximum.5 (/6") to left or right on both front and rear (tool-free) NOTE: Side adjustment not available on T5.x8xx locking devices 0 Blum, Inc. NOTE: For T5.90.PS setback in inset applications, see page 5

2 Drawer specifications Face frame and panel applications Preparing for hardware installation Front view opening width inside width = opening width minus 4 6 (/4") minimum top clearance Installation screw 75 ocking device T5.90 with side adjustment or T5.80 without side adjustment preboring holes for locking devices #6 head wood or system screws 7 (-5") (/6") side maximum 6 (5/8") (/") height maximum = opening minus 0 (5") opening height preboring holes for rear hooks.5 mm bit with extension chuck 4 (9/6") bottom clearance 6 mm bit with stop collar Template T NOTE: Because material may vary, the inside width must equal opening width minus 4 for TANDEM to align and function properly NOTE: Use of the T template is essential for accurate location and angle of pre-bored locking device holes and accurate boring for rear hook holes Drawer insertion Extend the runners fully. Place the on the runners and close. The locking devices automatically engage with the runners. Make adjustments if necessary. Drawer removal Squeeze orange handles on locking devices Pull straight out and up 0 Blum, Inc.

3 Face frame application unner mounting specifications Cabinet and specifications 60 (4") rear bracket inside depth range 557 to 599 (-5/6" to -9") mounting position 0 (") 557 (-5/6") minimum setback (/8") face 56H50B 5 (") bracket range 6 to 48 (/4" to -7/8") depth inside depth runner face mounting position 0 (") 60 (4") 5 (") blocking for frame applications 480 to 5 (8-9" to 0-9/6") 56.50B 5 (") 56H4570B 457 (8") Target Drawer ength setback (/8") 7 (-5") 5 (") minimum top clearance 6 (/4") maximum height = opening minus 0 (5") 5 (") 480 (8-9") minimum B 457 (8") mounting screws (#6 x 5/8" wood screw) rear mount bracket gap.5 (/6") bottom clearance 4 (9/6") blocking for frame applications 404 to 446 (5-9" to 7-9/6") 457 (8") 56H80B 8 (5") bottom recess (/") detail of front holes (-/4") 9 (") typical 7 (9") 5 (") 4 (-") 7(-5") 8 (5") 05 (") 8 to 70 (-9" to 4-9/6") *see below 56H050B 05 (") 56H90B0 9 (9") *bracket maximum depth minimum depth (-") 66 (0-5") (-5") 8 (-5") NOTE: *These brackets are for 56H90B0 only NOTE: Orange dots indicate screw locations required to meet specified load capacities depth inside depth maximum minimum 56H50B 60 (4") 599 (-9") 557 (-5/6") 5 (") maximum runner 548 (-9/6") 56.50B 60 (4") 557 (-5/6") 5 (") 548 (-9/6") 56H4570B 5 (") 5 (0-9/6") 480 (8-9") 457 (8") 47 (8-7") B 5 (") 480 (8-9") 457 (8") 6 (5/8") 47 (8-7") 56H80B 457 (8") 446 (7-9/6") 404 (5-9") 8 (5") 95 (5-9/6") 56H050B 8 (5") 70 (4-9/6") 8 (-9") 05 (") 9 (-9/6") 56H90B0 05 (") 99 (-5") 66 (0-5") 9 (9") 59 (0-/6") NOTE: For 56. series runners rear brackets and sockets cannot be used. Cabinet sides must be blocked-out flush with the inside of the frame. T5.90 ocking device with side adjustment (right) ear mounting bracket, non-handed T5.90 ocking device with side adjustment (left) H90B0 rear bracket, non-handed T5.80 ocking device (right) H90B0 rear bracket, non-handed T5.80 ocking device (left) #6 Wood screw (for mounting runner to side, rear brackets and locking devices) 0 Blum, Inc.

4 Panel application unner mounting specifications Cabinet and specifications 60 (4") 56 (0-") mounting position 7 (-5") 4 (8-/6") 8 (") typical setback (/8") 557 (-5/6") minimum face 56H50B 5 (") depth inside depth runner face mounting position 7 (-5") 60 (4") 4 (8-/6") 56.50B 5 (") setback (/8") 7 (-5") 5 (") minimum top clearance 6 (/4") 5 (") 557 (-5/6") minimum 9 (7-9/6") 4 (8-/6") 480 (8-9") minimum 56H4570B 457 (8") gap.5 (/6") maximum height = opening minus 0 (5") bottom clearance 4 (9/6") 4 (8-/6") 5 (") B 457 (8") 480 (8-9") minimum 457 (8") detail of front holes (-/4") 7 (9") 5 (") 4 (-") 8 (5") 9 (") typical 7 (-5") 05 (") 9 (7-9/6") 404 (5-9") minimum 96 (-5") 8 (5-") 8 (5-") 8 (-9") minimum 96 (-5") 96 (-5") 66 (0-5") minimum NOTE: Orange dots indicate screw locations required to meet specified load capacities 56H80B 8 (5") 56H050B 05 (") 56H90B0 9 (9") depth minimum inside depth 56H50B 60 (4") 557 (-5/6") 5 (") maximum runner 548 (-9/6") 56.50B 60 (4") 557 (-5/6") 5 (") 548 (-9/6") 56H4570B 5 (") 480 (8-9") 457 (8") 47 (8-7") B 5 (") 480 (8-9") 457 (8") 6 (5/8") 47 (8-7") 56H80B 457 (8") 404 (5-9") 8 (5") 95 (5-9/6") 56H050B 8 (5") 8 (-9") 05 (") 9 (-9/6") 56H90B0 05 (") 66 (0-5") 9 (9") 59 (0-/6") T5.90 T5.90 T5.80 T HG ocking device with side adjustment (right) ocking device with side adjustment (left) ocking device (right) ocking device (left) #6 Wood screw (for mounting runner to side, rear brackets and locking devices) #6 System screw (for mounting runner to side) bottom recess (/") 4 0 Blum, Inc.

5 Inset application Face frame application complete blockout (see table) Trial recommended blocking behind frame Face frame application partial blockout (see table) Trial recommended blocking behind frame Panel application (see table) Trial recommended inside depth minimum = runner + setback + 6 (/4") inside depth range minimum = runner + setback + 6 (/4") maximum with bracket = runner + setback + 48 (-7/8") inside depth range minimum = runner + setback + 6 (/4") Setback information unner setback when using depth adjustable locking device (T5.90.PS) sub-front mounting hole position front NOTE: unner cannot be mounted below opening 56/569 H/. Setbacks in this table recess the sub-front (/") 0 (5") (9") 6 (-") 6 (5/8") (9") 6 (-") 9 (-5") 9 (/4") 6 (-") 9 (-5") (-/4") 6 (5/8") 9 (/4") (7/8") calculating unner setback when using all other locking devices front face of the front inside of the (") The depth adjustment can then be used to move the front out to its desired position,.5 (") out adjustment only 56/569 H/. sub-front + front minus 9 (") 56/569 H/. Setbacks in this table set the sub-front (/") 7.5 (/6") 0.5 (/6").5 (5/6") 6 (5/8") 0.5 (/6").5 (5/6") 6.5 (-") 9 (/4").5 (5/6") 6.5 (-") 9.5 (-5") 6 (5/8") 9 (/4") (7/8") front face of the front flush with the face of the If a depth adjustable locking device is needed, please see the locking device and table above NOTE: For mounting hole position add 7 (9") to calculating 56/569 H/. sub-front + front minus.5 (7/6") 5 0 Blum, Inc.

6 Attachment specifications ear attachment options for face frame applications Front view rear mounting bracket, non-handed x for 56H90B0, non-handed 6 (5/8") (-/4") (") (/6") 4 (9/6") (5") 7.5 (/6") (-/4") 4 (5") 9.5 (-9/6") 6 (5/8") 5 (/6") Depth adjustment specifications B A 0.5 (/6") Mount each runner using at least two of the elongated holes. Install the to check the position of the front. A 56H50B 44.5 (9-5/8") (9-") 56.50B 44.5 (9-5/8") 56H4570B 44.5 (9-5/8") 46.5 (7-/6") B 44.5 (9-5/8") 56H80B 48.5 (5-7") 40.5 (-") 56H050B 48.5 (5-7") 44.5 (9-5/8") 56H90B0 6.5 (4-9").5 (8-/8") emove the, loosen screws and make adjustments if necessary, ±4.5 (/6"). Tighten the screws, verify the front position and finish mounting the runners using the screw locations indicated by the orange dots. B Bottom mounting specifications Plug-in socket, non handed 9 (") Screw-on socket, non handed 9 (") Top view 9 (") X 9 (") 67 (-5/8") Ø8 7 (-5") Z (-/4") Y. (/8") 6 (5/8") 6.5 (/4") NOTE: Use at least three installation screws for or x 40 (-9/6") (") 9 (/4") minimum inside depth (/8") X Y Z 56H50B 5 (") 557 (-5/6") 448 (7-5/8") (5") 9 (/4") 56.50B 5 (") 557 (-5/6") 58 (4-") (5") 9 (/4") 56H4570B 457 (8") 480 (8-9") 78 (4-7/8") (5") 9 (/4") B 457 (8") 480 (8-9") 58 (4-") (5") 9 (/4") 56H80B 8 (5") 404 (5-9") 9 (-9/6") (5") 9 (/4") Millimeter to inch conversion chart /6 /8 5 /6 7 /4 9 5 /6 /8 7 /6 5 / 7 9 /6 9 5 /8 /6 /4 5 /6 7 7 /8 9 5 /6 6 0 Blum, Inc. INST-TDM56H-56.0.