Medium Pressure Products MPI Fittings, Valves, Regulators and Hoses 6,000-20,000 PSI Range. Catalog 4234 Revised, September 2003

Transcription

1 Medium Pressure Products Fittings, Valves, Regulators and Hoses 6,000-20,000 PSI Range Catalog 4234 Revised, September 2003

2 Fittings Medium Pressure Fittings Introduction Parker Hannifin Fittings* have been engineered and manufactured to provide secure, tight, and leakresistant connections throughout industry, including off-shore oil and gas exploration platforms, research labs, and other facilities that require operating pressures in the range of 6,000 to 15,000 psi. Fittings are ideally suited to handle liquids, gases, or chemicals and can be used on a wide variety of tubing materials including cold drawn - 1/8 hard (unannealed) tubing or instrument grade thick-walled annealed stainless steel. Every Parker Fitting is supplied complete and ready to install. Advanced Features Every Fitting has the features shown below: Materials and Identification Standard Fittings are made of Heat Code Traceable 316 stainless steel. Tubing and fitting materials should be selected based on compatibility with the fluid or gas media. Part numbers for Fittings use symbols that identify their style, size, and composition. Fittings Pressure Ratings The maximum pressure rating is marked on each fitting. Fittings are designed to a 4 to 1 safety factor. Size 4 end to 15,000 psi Size 6 end to 15,000 psi Size 8 end to 12,500 psi Size 9 end to 12,500 psi Assembly Fittings are installed with standard hand tools. Each size can be preset with a Parker hydraulic preset tool. Tube preparation does not require cutting of threads or tube end coning Front ferrule with corrosion-resistant Parker SUPARCASE forms a tight pressure seal between the body and ferrule in a second strong mechanical hold on the tube. 2. Rear ferrule with corrosion-resistant Parker SUPARCASE provides a strong mechanical hold on the tube. 3. Longer thread area for improved resistance to pressure and load on the ferrules. 4. Molybdenum disulfide-coated inverted nut helps prevent galling, provides easier assembly, and permits multiple remakes. 5. Long tube-support area improves resistance to vibration and line loads. *Patent Pending Dedication To Quality Our resources and vast product line, is available through our worldwide distribution network. For more information regarding our products and services, please contact your authorized Parker Instrumentation Distributor. 2 Parker Hannifin Corporation Huntsville, Alabama

3 Medium Pressure Fittings Assembly, Remake & Gaugeability Instructions 1. Parker Fittings are sold completely assembled and ready for immediate use. Simply insert the tube as illustrated until it bottoms in the fitting body. (If the fitting is disassembled, note that the small tapered end of the ferrule(s) go into the fitting body.) 2. For Fittings from 1/4 to 1, turn the nut to the finger-tight position. Hold the fitting body hex with a second wrench to prevent the body from turning as you continue tightening the nut. Use a wrench to tighten the nut 1 1/2 turns. Parker recommends that you mark the nut (using a scribe or ink) to help you count the turns. 3. For maximum number of remakes, mark the fitting and nut before disassembly. Before retightening, make sure the assembly has been inserted into the fitting until the ferrule seats in the fitting. Retighten the nut by hand. Rotate the nut with a wrench to the original position as indicated by the previous marks lining up. (A noticeable increase in mechanical resistance will be felt indicating the ferrule is being re-sprung into sealing position.) 4. Finally, check the gap between the nut and the body hex with the end of the gauge by inserting the gauge (as shown) into the beveled gap between the nut and body hex. Gently turn the gauge (that is, it twists out ). However, if the gauge slides into the beveled gap, (does not twist out ) the fitting is not properly made up and you must check the entire assembly procedure. ARNING FAILURE, IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice. Copyright 2003, Parker Hannifin Corporation. All Rights Reserved. Offer of Sale The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated in the Offer of Sale. 3 Parker Hannifin Corporation Huntsville, Alabama

4 Fittings Medium Pressure Fittings Introduction Fittings FBMP7 Male Connector... Page 9 T7HBT7 Tube Port Connector... Page 12 T7NBT7 45 o Tube Stub Elbow... Page 15 SBMP7 to Male Branch NPT Tee... Page 18 XHBMP7 37 o Flare to Connector... Page 9 T7HF Tube Stub to Male NPT Pipe... Page 12 EBMP7 Union Elbow... Page 16 FNMP7 Plug... Page 18 MP7H2BX 37 o Flare Bulkhead to Connector... Page 9 XHT7 37 o Flare to Tube Stub... Page 13 PNBMP7 Cap... Page 18 X41HBMP7 High Pressure to Connector... Page 10 X41HT7 High Pressure to Tube Stub... Page 13 T7EBT7 Tube Elbow... Page 16 MPFF Front Ferrule... Page 18 X42HBMP7 Medium Pressure to Connector... Page 10 X42HT7 Medium Pressure to Tube Stub... Page 13 MPBF Back Ferrule... Page 19 MP7HBA to SAE Male O-ring Connector... Page 11 T7HOA Tube Stub to Male SAE O-ring... Page 14 CBMP7 to Male NPT Elbow... Page 16 BMP7 Nut... Page 19 M40HBMP7 Type M High Pressure Hose to Connector... Page 11 TRBMP7 Tube Stub Reducer... Page 14 JBMP7 Union Tee... Page 17 Assembly, Remake & Gaugeability Instructions... Page 3 Typical Raw Materials... Page 6 HBMP7 to Union Connector... Page 12 MP7PC Port Connector... Page 15 How To Order... Page 6 Tubing Selection Guide... Page 7 BMP7 Bulkhead Union Connector... Page 12 NBMP7 45 o Union Elbow... Page 15 RBMP7 to Male Run NPT Tee to Male SAE O-ring... Page 17 Fitting Presetting Tool Kit... Page 19 4 Parker Hannifin Corporation Huntsville, Alabama

5 9MP7-MPNXBD-T-SS 9MP7-MPBLPKH-V-SSP 9MP7-MPBXPK-V-SSP Medium Pressure Products Fittings Medium Pressure Valves Cone and Thread Fittings Two ay Inline Valves... Page 20 Two ay Angle Valves (Replaceable Seat)... Page 23 Union Couplings Cone and Thread... Page 30 Connection Components Cone and Thread... Page 31 Bulkhead Union Cone and Thread... Page 30 Caps Cone and Thread... Page 32 9MP7-MPNLB-T-SS 9MP7-MPNABR-T-SS Two ay Angle Valves... Page 21 Two ay Ball Valves... Page 24 Medium Pressure Elbows Cone and Thread... Page 30 Medium Pressure Anti- Vibration Gland Assemblies Cone and Thread... Page 32 9MP7-MPNAB-T-SS Medium Pressure Tees Cone and Thread... Page 31 Anti-Vibration Component Part Numbers Cone and Thread... Page 32 Three ay/two Pressure Connections... Page 22 Three ay Ball Valves... Page 25 Medium Pressure Crosses Cone and Thread... Page 31 9MP7-MPNXBI-T-SS Three ay/one Pressure Connection... Page 22 9MP7-MPNXBO-T-SS Inline Filters... Page 26 9MP7-MPFL-40-SS Ball Check Valves... Page 27 9MP7-MPCBL-5-SS Check Valves... Page 28 Medium Pressure Ball Valve Medium Pressure Ball Valve... Page 33 Medium Pressure Regulators Medium Pressure Regulators XPR Series... Page 33 How to Order... Page 33 9MP7-MPCL-5-V-SS Three ay/two Stem Connection... Page 23 Relief Valves (Factory Set)... Page 29 polyflex Hose 2020N Page 34 How to Order... Page N Page 34 5 Parker Hannifin Corporation Huntsville, Alabama

6 Fittings Medium Pressure Fittings Typical Raw Material Specifications Basic Fitting Material Bar Stock Forging STAINLESS STEEL ASME SA-479 ASME SA (Type 316) (1) Type 316-SS BS S31 BS S31 DIN 4401 DIN 4401 (1) If additional information, including heat code traceability, is required, contact Parker Hannifin or your nearest Fitting distributor. (2) Stainless steel Parker Fittings work reliably on cold drawn - 1/8 hard (unannealed), thick-wall 316 tubing and fully annealed type 316 tubing. Tube End Dimensional Data Size No. Tube O.D. Inches Straight Thread C D E 4 1/4 1/ /16 6 3/8 5/ /16 8 1/2 13/ /16 9 9/16 7/ * L = Recommended Straight Length of Circular Un-bent Tubing "D" "C" *L "" "E" How To Order Fittings Parker Fittings should be ordered using the part number as listed in this catalog. Part numbers are developed as follows: 1. A combination of letters and numbers identifies the size and style of the fitting and the material used. 2. Tube and pipe thread sizes are designated by the number of sixteenths of an inch (1/4 tube = 4/16 or 4). All standard Fittings are manufactured from 316 stainless steel. Other materials are available upon special order. "L" Straights and Elbows: Specify the largest end of the MPI first, followed by the smaller tube end OR pipe thread size. Example: Part number 4-4 HBMP7 union would have the specifications listed below. 4-4 HBMP7 Tees: Example: Part number JBMP7 would have the following specifications: JBMP HB MP7 - SS 1/4 1/4 Union Medium Stainless Tube Tube Pressure Steel Inverted JB MP7 - SS 3/8 3/8 3/8 Tee Medium Stainless Tube Tube Branch Pressure Steel Inverted (1) (2) (3) Customer Requests: hen special configurations are required, please provide a blueprint of the installation to Parker with your request for a price quote. 6 Parker Hannifin Corporation Huntsville, Alabama

7 Medium Pressure Fittings Tubing Selection Guide Although Parker s Fittings have been engineered and manufactured to consistently provide high levels of reliability, no system s integrity is complete without considering the critical link: tubing. This section is intended to help you properly select and order quality tubing, both annealed and mediumpressure cold drawn - 1/8 hard (unannealed). Parker believes that proper tubing selection and installation are key to building leak-free, reliable tubing systems. Parker s Fittings have been designed to operate on a wide variety of medium pressure applications (6,000 to 15,000 psi). General Selection Criteria The data tables in this section will help you select the tubing that best satisfies the needs of the application. The most important consideration in the selection of suitable tubing for any application is the compatibility of the tubing materials with the media to be contained. System Pressure The system operating pressure is another important factor in determining the type, and more importantly, the size of tubing to be used. In general, high pressure installations require strong materials such as stainless steel.tube fitting assemblies should never be pressurized beyond the recommended working pressure. Maximum Allowable orking Pressure Tables Table 1 lists 316 stainless steel along with its associated general applications and recommended temperature ranges. Tubing Compatibility Table 1 Tubing General Recommended Material Application Temperature Range Stainless Steel High Pressure, High Temperature, Generally Corrosive Media -425 F to 1200 F (1) (-255 C to 650 C) (1) For operating temperatures above 800 F (425 C), consideration should be given to media. 300 Series Stainless Steels are susceptible to carbide precipitation which may lead to intergranular corrosion at elevated temperatures. All temperature ratings based on maximum rated temperatures per ASME/ANSI B31.3 Chemical Plant and Petroleum Refinery Piping Code, 1999 Edition. The information listed in Table 1 is general in scope. For specific applications, please contact Parker s, Product Engineering Department (256) Inside R & D facilities at major industrial plants, Fittings withstand the rigors of pressurized testing systems and other high stress applications. 7 Parker Hannifin Corporation Huntsville, Alabama

8 Fittings Medium Pressure Fittings Tables 2 and 3 list the maximum suggested working pressure of various tubing sizes, according to material. Acceptable tubing diameters and wall thicknesses are those for which a rating is listed. Combinations which do not have a pressure rating are not recommended for use with Fittings. Medium Pressure Tubing Fittings are designed to work with stainless steel, seamless, cold drawn - 1/8 hard, (unannealed) tubing. Tensile strength is approximately 40% higher than that of annealed tubing. Table 2 Tube Size 316 Stainless Steel (Seamless/Unannealed - 1/8 Hard) Nominal OD (in.) Nominal ID (in.) orking Pressure Nominal ID (in.) orking Pressure 1/ ,000 3/ , ,000 9/ ,500 NOTE: orking pressures calculated using an allowable stress of 35,000 psi for 1/8 hard 316 stainless steel tubing with a minimum tensile strength of 105,000 psi. NOTE: fittings are designed to work with nominal O.D. 1/8 hard tubing with a max. O.D. tolerance of ±.004. Consult the factory for possible use with tubing ouside this tolerance range. *Consult the factory for pressure tables regarding other materials. **.359 I.D. limited to 12,500 psi working pressure when used with fittings. Instrumentation Grade Tubing Table 3 Tube 316 Stainless Steel (Seamless/Annealed) O.D. Size (in.) /4 10,300 13,300 3/8 6,600 8,600 10,000 11,700 1/2 6,700 7,800 9,100 10,000 11,400 NOTE: orking pressures calculated using an allowable stress of 20,000 psi for annealed 316 stainless steel tubing with a nominal O.D. tolerance of ±.005. At chemical plants, corrosion-resistance on flow lines, injections pumps, control panels, and tubing systems is crucial for dependable operation. Fittings meet the challenge. 8 Parker Hannifin Corporation Huntsville, Alabama

9 Medium Pressure Fittings FBMP7 to Male NPT Connector "" "D" FBMP7 "B" NPT THREADS SIZE NPT THREAD A B D 4-2 FBMP7 1/4 1/ /8 15, FBMP7 1/4 1/ /8 15, FBMP7 1/4 3/ /4 12, FBMP7 1/4 1/ /8 10, FBMP7 3/8 1/ /4 15, FBMP7 3/8 3/ /4 12, FBMP7 3/8 1/ /4 10, FBMP7 1/2 3/ " 12, FBMP7 1/2 1/ " 10, FBMP7 9/16 3/ /16 12, FBMP7 9/16 1/ /16 10,000 XHBMP7 37º Flare to Connector "B" "D" "T" THREADS "" 37 O FLARE ADAPTER SIZE A B D T THREAD 4-4 XHBMP7 1/4 1/ / /8 15, XHBMP7 1/4 3/ / /4 15, XHBMP7 1/4 1/ / , XHBMP7 1/4 9/ / /16 12, XHBMP7 3/8 1/ / /8 12, XHBMP7 3/8 3/ / /4 12, XHBMP7 3/8 1/ / , XHBMP7 3/8 9/ / /16 12, XHBMP7 1/2 3/ / /16 12, XHBMP7 1/2 1/ / , XHBMP7 1/2 9/ / /16 12,500 MP7H2BX 37º Flare Bulkhead to Connector "H" MAX "B" "T" THREADS "LN" "" 37 o FLARE ADAPTER SIZE A B H MAX T THREAD 4-4 MP7H2BX 1/4 1/ / /16 5/8 15, MP7H2BX 3/8 3/ / /16 3/4 12, MP7H2BX 1/2 1/ / , MP7H2BX 1/2 9/ / /16 12,500 LN 9 Parker Hannifin Corporation Huntsville, Alabama

10 Fittings Medium Pressure Fittings X41HBMP7 High Pressure to Connector "B" "D" "T" THREADS "" HIGH ADAPTER SIZE A B D T THREAD 4-4 X41HBMP7 1/4 1/ / /8 15, X41HBMP7 1/4 3/ / /4 15, X41HBMP7 3/8 1/ / /16 15, X41HBMP7 3/8 3/ / /16 15, X41HBMP7 3/8 9/ / /16 12, X41HBMP7 9/16 3/ / /16 15, X41HBMP7 9/16 9/ / /16 12,500 X42HBMP7 Medium Pressure to Connector "B" "D" "T" THREADS "" MEDIUM ADAPTER SIZE A B D T THREAD 4-4 X42HBMP7 1/4 1/ / /8 15, X42HBMP7 1/4 3/ / /4 15, X42HBMP7 1/4 9/ / /16 12, X42HBMP7 3/8 1/ / /4 15, X42HBMP7 3/8 3/ / /4 15, X42HBMP7 3/8 1/ / , X42HBMP7 3/8 9/ / /16 12, X42HBMP7 9/16 1/ / /8 15, X42HBMP7 9/16 3/ / /8 15, X42HBMP7 9/16 1/ / , X42HBMP7 9/16 9/ / /16 12, Parker Hannifin Corporation Huntsville, Alabama

11 Medium Pressure Fittings MP7HBA to SAE Male O-ring Connector "D" "B" "" "T" THREADS SIZE SAE* END A B D T THREAD 4-4 MP7HBA 1/4 1/ / /8 12, MP7HBA 1/4 3/ / /16 12, MP7HBA 1/4 1/ /4-16 7/8 12, MP7HBA 3/8 1/ / /4 12, MP7HBA 3/8 3/ / /4 12, MP7HBA 3/8 1/ /4-16 7/8 12, MP7HBA 1/2 1/ / , MP7HBA 1/2 3/ / , MP7HBA 1/2 1/ / , MP7HBA 9/16 3/ / /16 12, MP7HBA 9/16 1/ / /16 12,500 *All male o-ring ends for fittings are heavy duty and comply with SAE J This end has maximum thread engagement for strength and requires the minimum full thread engagement specified in SAE J9126 for the female port. M40HBMP7 Type M High Pressure Hose to Connector "B" "D" "T" THR'D "" HOSE* ADAPTER SIZE A B D T THREAD 6-4 M40HBMP7-6 1/ / /8 15, M40HBMP7-6 3/ / /4 15, M40HBMP7-8 3/ / /16 15, M40HBMP7-8 1/ /4-16 1" 12, M40HBMP7-8 9/ / /16 12, M40HBMP7-10 1/ / /16 15, M40HBMP7-10 3/ / /16 12, M40HBMP7-11 1/ " /16 12, M40HBMP7-11 9/ " /16 12,500 * Adapts to Type M Swivel Hose Connection 11 Parker Hannifin Corporation Huntsville, Alabama

12 Fittings Medium Pressure Fittings HBMP7 to Union Connector "" "D" HBMP7 BMP7 Bulkhead Union Connector "T" "D" "H" Max "" T7HBT7 Tube Port Connector T7HF Tube Stub to Male NPT Pipe "T" "L" "" "B" "T" THREADS SIZE A 4-4 HBMP7 1/ /8 15, HBMP7 3/ /4 15, HBMP7 1/ , HBMP7 9/ /16 12,500 SIZE TUBE STUB A TUBE SIZE * 4-4 T7HBT7-SS 1/ , T7HBT7-SS-4 1/ , T7HBT7-SS-6 1/ , T7HBT7-SS-9 1/ , T7HBT7-SS-12 1/ ,000 * 6-6 T7HBT7-SS 3/ , T7HBT7-SS-4 3/ , T7HBT7-SS-6 3/ , T7HBT7-SS-9 3/ , T7HBT7-SS-12 3/ ,000 * 9-9 T7HBT7-SS 9/ , T7HBT7-SS-6 9/ , T7HBT7-SS-9 9/ , T7HBT7-SS-12 9/ ,500 * Same Assembled Length as MP7PC L MALE NPT END A D D H MAX T 4-4 BMP7 1/ , BMP7 3/ /8 15, BMP7 1/ /8 12, BMP7 9/ /8 12, T7HF 1/4 1/ /4-18 5/8 15, T7HF 1/4 3/ /8-18 3/4 12, T7HF 1/4 1/ /2-14 7/8 10, T7HF 3/8 1/ /4-18 5/8 12, T7HF 3/8 3/ /8-18 3/4 12, T7HF 3/8 1/ /2-14 7/8 10, T7HF 1/2 1/ /4-18 5/8 12, T7HF 1/2 3/ /8-18 3/4 12, T7HF 1/2 1/ /2-14 7/8 10, T7HF 9/16 1/ /4-18 5/8 12, T7HF 9/16 3/ /8-18 3/4 12, T7HF 9/16 1/ /2-14 7/8 10,000 Add -Z6 to part number for part assembled with preset ferrules and nuts B T THREAD 12 Parker Hannifin Corporation Huntsville, Alabama

13 Medium Pressure Fittings XHT7 37º Flare to Tube Stub "T" THR'D "" 37 O FLARE ADAPTER SIZE TUBE STUB 4-4 XHT7 1/4 1/ / /2 12, XHT7 1/4 3/ / /2 12, XHT7 3/8 1/ / /8 12, XHT7 3/8 3/ / /8 12, XHT7 3/8 1/ / /8 12, XHT7 3/8 9/ / /8 12, XHT7 1/2 3/ / /16 12, XHT7 1/2 1/ / /16 12, XHT7 1/2 9/ / /16 12,500 Add -Z6 to part number for part assembled with preset ferrules and nuts A T THREAD X41HT7 High Pressure to Tube Stub "" "T" THR'D HIGH ADAPTER SIZE TUBE STUB 4-4 X41HT7 1/4 1/ / /8 15, X41HT7 1/4 3/ / /8 12, X41HT7 1/4 1/ / /8 12, X41HT7 1/4 9/ / /8 12, X41HT7 3/8 1/ / /16 15, X41HT7 3/8 3/ / /16 12, X41HT7 3/8 1/ / /16 12, X41HT7 3/8 9/ / /16 12, X41HT7 9/16 1/ / /16 15, X41HT7 9/16 3/ / /16 12, X41HT7 9/16 1/ / /16 12, X41HT7 9/16 9/ / /16 12,500 Add -Z6 to part number for part assembled with preset ferrules and nuts A T THREAD X42HT7 Medium Pressure to Tube Stub "" "T" THR'D MEDIUM ADAPTER SIZE TUBE STUB 4-4 X42HT7 1/4 1/ / /8 15, X42HT7 1/4 3/ / /8 12, X42HT7 1/4 1/ / /8 12, X42HT7 1/4 9/ / /8 12, X42HT7 3/8 1/ / /4 15, X42HT7 3/8 3/ / /4 12, X42HT7 3/8 1/ / /4 12, X42HT7 3/8 9/ / /4 12, X42HT7 9/16 1/ / /8 15, X42HT7 9/16 3/ / /8 12, X42HT7 9/16 1/ / /8 12, X42HT7 9/16 9/ / /8 12,500 Add -Z6 to part number for part assembled with preset ferrules and nuts A T THREAD 13 Parker Hannifin Corporation Huntsville, Alabama

14 Fittings Medium Pressure Fittings T7HOA Tube Stub to Male SAE O-ring "" "B" "T" THREADS SAE TUBE STUB O-RING END A 4-4 T7HOA 1/4 1/ / /16 12, T7HOA 1/4 3/ / /16 12, T7HOA 1/4 1/ /4-16 7/8 12, T7HOA 3/8 1/ / /16 12, T7HOA 3/8 3/ / /16 12, T7HOA 3/8 1/ /4-16 7/8 12, T7HOA 1/2 1/ / /16 12, T7HOA 1/2 3/ / /16 12, T7HOA 1/2 1/ /4-16 7/8 12, T7HOA 9/16 1/ / /8 12, T7HOA 9/16 3/ / /16 12, T7HOA 9/16 1/ /4-16 7/8 12,500 Add -Z6 to part number for part assembled with preset ferrules and nuts * All male o-ring ends for fittings are heavy duty and comply with SAE J This end has maximum thread engagement for strength and requires the minimum full thread engagement specified in SAE J9126 for the female port. B T THREAD TRBMP7 Tube Stub Reducer 1 "" 2 TUBE STUB #1 SIZE #2 4-6 TRBMP7 1/4 3/ /4 15, TRBMP7 1/4 1/ " 12, TRBMP7 1/4 9/ /16 12, TRBMP7 3/8 1/ /8 12, TRBMP7 3/8 1/ " 12, TRBMP7 3/8 9/ /16 12, TRBMP7 1/2 1/ /8 12, TRBMP7 1/2 3/ /4 12, TRBMP7 9/16 1/ /8 12, TRBMP7 9/16 3/ /4 12,500 Add -Z6 to part number for part assembled with preset ferrules and nuts A 14 Parker Hannifin Corporation Huntsville, Alabama

15 Medium Pressure Fittings MP7PC Port Connector "K" 1 2 TUBE STUB #1 PORT #2 4-4 MP7PC 1/4 1/ , MP7PC 1/4 3/ , MP7PC 3/8 3/ , MP7PC 3/8 1/ , MP7PC 9/16 3/ , MP7PC 1/2 1/ , MP7PC 9/16 9/ ,500 Add -Z6 to part number for part assembled with preset ferrules and nuts A K NBMP7 45º Union Elbow "L" "C" 135 "C" SIZE A 4-4 NBMP7 1/ /8 15, NBMP7 3/ /4 15, NBMP7 1/ , NBMP7 9/ ,500 C L TH'K "" TH'K T7NBT7 45º Tube Stub Elbow "L" "R" 45 "L" TUBE SIZE H R 4-4 T7NBT7-SS 1/ ,000 * 4-4 T7NBT7-SS-2.9 1/ , T7NBT7-SS-6 1/ , T7NBT7-SS-9 1/ , T7NBT7-SS-12 1/ , T7NBT7-SS 3/ ,000 * 6-6 T7NBT7-SS-3.4 3/ , T7NBT7-SS-6 3/ , T7NBT7-SS-9 3/ , T7NBT7-SS-12 3/ , T7NBT7-SS 9/ ,500 * 9-9 T7NBT7-SS-4.2 9/ , T7NBT7-SS-6 9/ , T7NBT7-SS-9 9/ , T7NBT7-SS-12 9/ ,500 * Similar Assembled Lengths as NBMP7 with Two (2) MP7PC s 15 Parker Hannifin Corporation Huntsville, Alabama

16 Fittings Medium Pressure Fittings EBMP7 Union Elbow "H" "C" "L" SIZE C 4-4 EBMP7 1/ /8 15, EBMP7 3/ /4 15, EBMP7 1/ , EBMP7 9/ ,500 H L TH'K "" TH'K "L" "H" "C" T7EBT7 Tube Elbow "R" "H" TYP. TUBE SIZE H R 4-4 T7EBT7-SS 1/ ,000 * 4-4 T7EBT7-SS-2.9 1/ , T7EBT7-SS-6 1/ , T7EBT7-SS-9 1/ , T7EBT7-SS-12 1/ , T7EBT7-SS 3/ ,000 * 6-6 T7EBT7-SS-3.5 3/ , T7EBT7-SS-6 3/ , T7EBT7-SS-9 3/ , T7EBT7-SS-12 3/ , T7EBT7-SS 9/ ,500 * 9-9 T7EBT7-SS-4.2 9/ , T7EBT7-SS-6 9/ , T7EBT7-SS-9 9/ , T7EBT7-SS-12 9/ ,500 * Similar Assembled Lengths as EBMP7 with Two (2) MP7PC s "C" "L" "" CBMP7 to Male NPT Elbow "B" SIZE NPT THREAD A B C L 4-4 CBMP7 1/4 1/ /4 15, CBMP7 1/4 3/ /4 12, CBMP7 1/4 1/ /4 10, CBMP7 3/8 1/ /8 12, CBMP7 3/8 3/ /8 12, CBMP7 3/8 1/ /8 10, Parker Hannifin Corporation Huntsville, Alabama

17 Medium Pressure Fittings JBMP7 Union Tee "C1" "L" "C2" "L" 1 2 "L" "" TH'K "H" 3 SIZE #1 SIZE #2 SIZE #3 A C1 C2 H L JBMP7 1/4 1/4 1/ /8 15, JBMP7 3/8 3/8 3/ /4 15, JBMP7 1/2 1/2 1/ , JBMP7 9/16 9/16 9/ ,500 TH'K JBMP7 1/4 1/4 3/ /4 15, JBMP7 3/8 3/8 1/ /4 15, JBMP7 3/8 1/4 1/ /4 15, JBMP7 3/8 3/8 1/ , JBMP7 3/8 3/8 9/ , JBMP7 1/2 1/2 3/ , JBMP7 1/2 3/8 3/ , JBMP7 9/16 9/16 1/ , JBMP7 9/16 9/16 3/ , JBMP7 9/16 3/8 1/ , JBMP7 9/16 3/8 3/ ,500 "C1" "C2" "B" RBMP7 to Male Run NPT Tee 2 "" "C3" SIZE #1 NPT THR'D #2 SIZE #3 A C1 C2 C3 B RBMP7 1/4 1/4-18 1/ /4 15, RBMP7 1/4 1/4-18 3/ /8 12, RBMP7 1/4 3/8-18 1/ /4 12, RBMP7 1/4 3/8-18 3/ /8 12, RBMP7 3/8 1/4-18 1/ /8 12, RBMP7 3/8 1/4-18 3/ /8 12, RBMP7 3/8 3/8-18 1/ /8 12, RBMP7 3/8 3/8-18 3/ /8 12,000 TH'K 17 Parker Hannifin Corporation Huntsville, Alabama

18 Fittings Medium Pressure Fittings SBMP7 to Male Branch NPT Tee "C1" "C2" "C3" "B" SIZE #1 NPT THR'D #2 SIZE #3 A C1 C2 C3 B SBMP7 1/4 1/4 1/ /4 15, SBMP7 1/4 3/8 3/ /4 12, SBMP7 3/8 1/4 1/ /8 12, SBMP7 3/8 3/8 3/ /8 12,000 TH'K FNMP7 Plug "" SIZE 4 FNMP7 1/ /16 15,000 6 FNMP7 3/ /16 15,000 8 FNMP7 1/ /16 12,500 9 FNMP7 9/ ,500 A PNBMP7 Cap "" "D" SIZE A 4 PNBMP7 1/ /8 15,000 6 PNBMP7 3/ /4 15,000 8 PNBMP7 1/ " 12,500 9 PNBMP7 9/ /16 12,500 D MPFF Front Ferrule Tube O.D. "D" TUBE O.D. FERRULE O.D. 4 MPFF 1/ MPFF 3/ MPFF 1/ MPFF 9/ Parker Hannifin Corporation Huntsville, Alabama

19 Medium Pressure Fittings MPBF Back Ferrule Tube O.D. "D" TUBE O.D. FERRULE O.D. 4 MPBF 1/ MPBF 3/ MPBF 1/ MPBF 9/ BMP7 Nut "" SIZE 4 BMP7 1/ /16 6 BMP7 3/ /16 8 BMP7 1/ /16 9 BMP7 9/ A Fitting Presetting Tool Kit An Fitting hydraulic presetting tool kit for Fittings ranging in size from 1/4 up to 9/16, is available to preset the ferrules on the tubing prior to assembly. The kit includes a preset Fitting head; an Enerpac hydraulic pump; the appropriate dies for the body and nut; and a heavy duty carrying case. hen ordering the kit, be sure to specify the Fitting presetting head. Gaugeability Tools MPIF Inspection Gauge This one handy gauge works for all sizes. The end of the gauge checks the fitting gap and tube insertion after make-up. Inspection Gauge (Size 4, 6, 9) For additional information about Fittings, including specification and installation instructions, contact your authorized Parker Instrumentation Distributor or the Parker Hannifin at (256) Parker Hannifin Corporation Huntsville, Alabama

20 FittingsMedium Pressure Valves Introduction Parker MPN series valves are designed for multi-turn control of media regulation and shutoff up to 20,000 psi. Additional packing materials are available for application temperatures from -300 o to 800 o F. Standard critical service design features, such as the packing below the thread and the non-rotating lower stem ensure longer valve life in rugged applications. Two ay Inline Valves "H" "G" "F" "C" 9MP7-MPNLB-T-SS "D" "E" "B" TUBING PSI CONNECTION ORIFICE A B C D E F G H TH'K 1/4" O.D. 4MP7-MPNLB-T-SS 15,000 4MP /4" O.D. 4MF-MPNLB-T-SS 20,000 4MF /8" O.D. 6MP7-MPNLB-T-SS 15,000 6MP /8" O.D. 6MF-MPNLB-T-SS 20,000 6MF /2" O.D. 8MP7-MPNLB-T-SS 12,500 8MF /16" O.D. 9MP7-MPNLB-T-SS 12,500 9MP /16" O.D. 9MF-MPNLB-T-SS 20,000 9MF /4" O.D. 12MF-MPNLB-T-SS 20,000 12MF /4" O.D. 12MF-MPNLBH-T-SS 10,000 12MF " O.D. 16MF-MPNLB-T-SS 20,000 16MF " O.D. 16MF-MPNLBH-T-SS 10,000 16MF PIPE SIZE PSI CONNECTION ORIFICE A B C D E F G H TH'K 1/8" NPT 2F-MPNLB-T-SS 15,000 1/8" NPTF /4" NPT 4F-MPNLB-T-SS 15,000 1/4" NPTF /8" NPT 6F-MPNLB-T-SS 15,000 3/8" NPTF /2" NPT 8F-MPNLB-T-SS 15,000 1/2" NPTF /4" NPT 12F-MPNLB-T-SS 10,000 3/4" NPTF " NPT 16F-MPNLB-T-SS 10,000 1" NPTF Materials of Construction Item # Description Material 1 Soc Set Screw Steel 2 Handle Aluminum 3 Upper Stem Assembly 17-4PH 4 Packing Gland 316SS 5 Locking Device 300 SER. SS X 1/4 Fill HD SCR. 300 SER. SS 7 Stem Pin 304SS 8 Top Packing asher 416SS 9 Packing Teflon 10 Bottom Packing asher 316SS 11 Lower Stem 17-4PH-H Body 316SS 20 Parker Hannifin Corporation Jacksonville, Alabama

21 Medium Pressure Fittings Valves Two ay Angle Valves "G" "H" "F" 9MP7-MPNAB-T-SS "D" "E" "B" TUBING PSI CONNECTION ORIFICE A B C D E F G H TH'K 1/4" O.D. 4MP7-MPNAB-T-SS 15,000 4MP /4" O.D. 4MF-MPNAB-T-SS 20,000 4MF /8" O.D. 6MP7-MPNAB-T-SS 15,000 6MP /8" O.D. 6MF-MPNAB-T-SS 20,000 6MF /2" O.D. 8MP7-MPNAB-T-SS 12,500 8MP /16" O.D. 9MP7-MPNAB-T-SS 12,500 9MP /16" O.D. 9MF-MPNAB-T-SS 20,000 9MF /4" O.D. 12MF-MPNAB-T-SS 20,000 12MF /4" O.D. 12MF-MPNABH-T-SS 10,000 12MF " O.D. 16MF-MPNAB-T-SS 20,000 16MF " O.D. 16MF-MPNABH-T-SS 10,000 16MF PIPE SIZE PSI CONNECTION ORIFICE A B C D E F G H TH'K 1/8" NPT 2F-MPNAB-T-SS 15,000 1/8" NPTF /4" NPT 4F-MPNAB-T-SS 15,000 1/4" NPTF /8" NPT 6F-MPNAB-T-SS 15,000 3/8" NPTF /2" NPT 8F-MPNAB-T-SS 15,000 1/2" NPTF /4" NPT 12F-MPNAB-T-SS 10,000 3/4" NPTF " NPT 16F-MPNAB-T-SS 10,000 1" NPTF Parker Hannifin Corporation Jacksonville, Alabama

22 FittingsMedium Pressure Valves Three ay/two Pressure Connections "G" "H" "F" 9MP7-MPNXBI-T-SS "E" "C" "D" "B" TUBING PSI CONNECTION ORIFICE A B C D E F G H TH'K 1/4" O.D. 4MP7-MPNXBI-T-SS 15,000 4MP /4" O.D. 4MF-MPNXBI-T-SS 20,000 4MF /8" O.D. 6MP7-MPNXBI-T-SS 15,000 6MP /8" O.D. 6MF-MPNXBI-T-SS 20,000 6MF /2" O.D. 8MP7-MPNXBI-T-SS 12,500 8MP /16" O.D. 9MP7-MPNXBI-T-SS 12,500 9MP /16" O.D. 9MF-MPNXBI-T-SS 20,000 9MF /4" O.D. 12MF-MPNXBI-T-SS 20,000 12MF /4" O.D. 12MF-MPNXBIH-T-SS 10,000 12MF " O.D. 16MF-MPNXBI-T-SS 20,000 16MF " O.D. 16MF-MPNXBIH-T-SS 10,000 16MF Three ay/one Pressure Connection "G" "H" "F" "C" 9MP7-MPNXBO-T-SS "D" "E" "B" TUBING PSI CONNECTION ORIFICE A B C D E F G H TH'K 1/4" O.D. 4MP7-MPNXBO-T-SS 15,000 4MP /4" O.D. 4MF-MPNXBO-T-SS 20,000 4MF /8" O.D. 6MP7-MPNXBO-T-SS 15,000 6MP /8" O.D. 6MF-MPNXBO-T-SS 20,000 6MF /2" O.D. 8MP7-MPNXBO-T-SS 12,500 8MP /16" O.D. 9MP7-MPNXBO-T-SS 12,500 9MP /16" O.D. 9MF-MPNXBO-T-SS 20,000 9MF /4" O.D. 12MF-MPNXBO-T-SS 20,000 12MF /4" O.D. 12MF-MPNXBOH-T-SS 10,000 12MF " O.D. 16MF-MPNXBO-T-SS 20,000 16MF " O.D. 16MF-MPNXBOH-T-SS 10,000 16MF Parker Hannifin Corporation Jacksonville, Alabama

23 Medium Pressure Fittings Valves Three ay/two Stem Connection "H" "G" "F" "C" "C" 9MP7-MPNXBD-T-SS "D" "D" "E" "B" TUBING PSI CONNECTION ORIFICE A B C D E F G H TH'K 1/4" O.D. 4MP7-MPNXBD-T-SS 15,000 4MP /4" O.D. 4MF-MPNXBD-T-SS 20,000 4MF /8" O.D. 6MP7-MPNXBD-T-SS 15,000 6MP /8" O.D. 6MF-MPNXBD-T-SS 20,000 6MF /2" O.D. 8MP7-MPNXBD-T-SS 12,500 8MP /16" O.D. 9MP7-MPNXBD-T-SS 12,500 9MP /16" O.D. 9MF-MPNXBD-T-SS 20,000 9MF /4" O.D. 12MF-MPNXBD-T-SS 20,000 12MF /4" O.D. 12MF-MPNXBDH-T-SS 10,000 12MF " O.D. 16MF-MPNXBD-T-SS 20,000 16MF " O.D. 16MF-MPNXBDH-T-SS 10,000 16MF Two ay Angle Valves (Replaceable Seat) "H" "G" "F" 9MP7-MPNABR-T-SS "D" "E" "B " TUBING PSI CONNECTION ORIFICE A B C D E F G H TH'K 1/4" O.D. 4MP7-MPNABR-T-SS 15,000 4MP /4" O.D. 4MF-MPNABR-T-SS 20,000 4MF /8" O.D. 6MP7-MPNABR-T-SS 15,000 6MP /8" O.D. 6MF-MPNABR-T-SS 20,000 6MF /2" O.D. 8MP7-MPNABR-T-SS 12,500 8MP /16" O.D. 9MP7-MPNABR-T-SS 12,500 9MP /16" O.D. 9MF-MPNABR-T-SS 20,000 9MF /4" O.D. 12MF-MPNABR-T-SS 20,000 12MF /4" O.D. 12MF-MPNABRH-T-SS 10,000 12MF " O.D. 16MF-MPNABR-T-SS 20,000 16MF " O.D. 16MF-MPNABRH-T-SS 10,000 16MF Parker Hannifin Corporation Jacksonville, Alabama

24 FittingsMedium Pressure Valves Introduction Parker MPB series manually, pneumatically and electrically actuated 2-way and 3-way ball valves are designed for 1/4 and 1/2 turn media shutoff or switching applications up to 20,000 psi. Our trunion style ball design and spring loaded seats make the MPB series ideal for severe service applications. The end connector design enables a variety of end connections and combinations for specific customer applications. Two ay Ball Valves THICK BLOCK PANEL MOUNT HOLE THICK BLOCK PANEL MOUNT HOLE MP7-MPBLPK-V-SSP MP7-MPBLPKH-V-SSP /32 O MOUNTING HOLES /32 O MOUNTING HOLES TUBING PSI CONNECTION ORIFICE MINIMUM ORIFICE C v A 1/8" O.D. 2F-MPBLPK-V-SSP 15,000 1/8" NPT /4" O.D. 4F-MPBLPK-V-SSP 15,000 1/4" NPT /4" O.D. 4MP7-MPBLPK-V-SSP 15,000 4MP /4" O.D. 4MF-MPBLPK-V-SSP 20,000 4MF /8" O.D. 6F-MPBLPK-V-SSP 15,000 3/8" NPT /8" O.D. 6MP7-MPBLPK-V-SSP 15,000 6MP /8" O.D. 6MF-MPBLPK-V-SSP 20,000 6MF /2" O.D. 8MP7-MPBLPK-V-SSP 12,500 8MP /16" O.D. 9MP7-MPBLPK-V-SSP 12,500 9MP /16" O.D. 9MF-MPBLPK-V-SSP 20,000 9MF /4" O.D. 4F-MPBLPKH-V-SSP 15,000 1/4" NPT /8" O.D. 6F-MPBLPKH-V-SSP 15,000 3/8" NPT /8" O.D. 6MP7-MPBLPKH-V-SSP 15,000 6MP /2" O.D. 8F-MPBLPKH-V-SSP 15,000 1/2" NPT /2" O.D. 8MP7-MPBLPKH-V-SSP 12,500 8MP /16" O.D. 9MP7-MPBLPKH-V-SSP 12,500 9MP /16" O.D. 9MF-MPBLPK-V-SSP 15,000 9MF /4" O.D. 12MF-MPBLPKH-V-SSP 15,000 12MF " O.D. 16MF-MPBLPKH-V-SSP 15,000 16MF Parker Hannifin Corporation Jacksonville, Alabama

25 Medium Pressure Fittings Valves Three ay Ball Valves THICK BLOCK 9MP7-MPBXPK-V-SSP 4.63 PANEL MOUNT HOLE THICK BLOCK 9MP7-MPBXPKH-V-SSP 4.63 PANEL MOUNT HOLE "B".25 9/32 O MOUNTING HOLES "B".25 9/32 O MOUNTING HOLES TUBING 3-AY 90 DEGREES 3-AY 180 DEGREES PSI CONNECTION ORIFICE MINIMUM ORIFICE C v A B 1/8" O.D. 2F-MPBXPKD-V-SSP 2F-MPBXPK-V-SSP 15,000 1/8" NPT /4" O.D. 4F-MPBXPKD-V-SSP 4F-MPBXPK-V-SSP 15,000 1/4" NPT /4" O.D. 4MP7-MPBXPKD-V-SSP 4MP7-MPBXPK-V-SSP 15,000 4MP /4" O.D. 4MF-MPBXPKD-V-SSP 4MF-MPBXPK-V-SSP 20,000 4MF /8" O.D. 6F-MPBXPKD-V-SSP 6F-MPBXPK-V-SSP 15,000 3/8" NPT /8" O.D. 6MP7-MPBXPKD-V-SSP 6MP7-MPBXPK-V-SSP 15,000 6MP /8" O.D. 6MF-MPBXPKD-V-SSP 6MF-MPBXPK-V-SSP 20,000 6MF /2" O.D. 8MP7-MPBXPKD-V-SSP 8MP7-MPBXPK-V-SSP 12,500 8MP /16" O.D. 9MP7-MPBXPKD-V-SSP 9MP7-MPBXPK-V-SSP 12,500 9MP /16" O.D. 9MF-MPBXPKD-V-SSP 9MF-MPBXPK-V-SSP 20,000 9MF /4" O.D. 4F-MPBXPKDH-V-SSP 4F-MPBXPKH-V-SSP 15,000 1/4" NPT /8" O.D. 6F-MPBXPKDH-V-SSP 6F-MPBXPKH-V-SSP 15,000 3/8" NPT /8" O.D. 6MP7-MPBXPKDH-V-SSP 6MP7-MPBXPKH-V-SSP 15,000 6MP /2" O.D. 8F-MPBXPKDH-V-SSP 8F-MPBXPKH-V-SSP 15,000 1/2" NPT /2" O.D. 8MP7-MPBXPKDH-V-SSP 8MP7-MPBXPKH-V-SSP 12,500 8MP /16" O.D. 9MP7-MPBXPKDH-V-SSP 9MP7-MPBXPKH-V-SSP 12,500 9MP /16" O.D. 9MF-MPBXPKD-V-SSP 9MF-MPBXPK-V-SSP 15,000 9MF /4" O.D. 12MF-MPBXPKDH-V-SSP 12MF-MPBXPKH-V-SSP 15,000 12MF " O.D. 16MF-MPBXPKDH-V-SSP 16MF-MPBXPKH-V-SSP 15,000 16MF Materials of Construction Item # Description Material 1 Handle 300 SER. SS 2 Set Screw 17-4PH-H900 3 Stop Collar, 180 Degree 300 SER. SS 4 Stem 17-4PH-H900 5 Panel Nut 300 SER. SS 6 Bearing asher Peek/30% Glass 7 O-ring Viton 8 Back Up Ring Teflon 9 Ball Seat Assembly 316SS/Arlon 10 Belleville asher 302SS 11 Packing asher 316SS 12 Back Up asher Teflon 13 Body Bushing Ampco Trunion, 180 Degree 316SS 15 Bottom Bushing Ampco Body 316SS 17 O-ring Viton 18 O-ring Viton 19 Seat Gland 316SS 20 Bottom Gland 316SS 25 Parker Hannifin Corporation Jacksonville, Alabama

26 FittingsMedium Pressure Valves Introduction Parker MPF series filters utilize sintered stainless steel filter discs to trap particles from 0.5 to 100 micron sizes. Inline filters help protect valuable equipment in the process line. Inline Filters LENGTH 9MP7-MPFL-40-SS FILTER MICRON SIZE AVAILABLE TUBING PSI CONNECTION ORIFICE LENGTH TH'K /4" O.D. 4MP7-MPFL-100-SS 15,000 4MP * * * * * * 1/4" O.D. 4MF-MPFL-100-SS 20,000 4MF * * * * * * 3/8" O.D. 6MP7-MPFL-100-SS 15,000 6MP * * * * * * 3/8" O.D. 6MF-MPFL-100-SS 20,000 6MF * * * * * * 1/2" O.D. 8MP7-MPFL-100-SS 12,500 8MP * * * * * * 9/16" O.D. 9MP7-MPFL-100-SS 12,500 9MP * * * * * * 9/16" O.D. 9MF-MPFL-100-SS 20,000 9MF * * * * * * Materials of Construction Item # Description Material 1 Cap 316SS 2 Sealing 316SS 3 Body 316SS 4 Spacer 316SS Micron Filter Disc 316SS 6 O-ring Teflon 26 Parker Hannifin Corporation Jacksonville, Alabama

27 Medium Pressure Fittings Valves Introduction Parker MPC and MPCB series check valves are designed for uni-directional flow control of fluids and gases up to 20,000 psi. Ball Check Valves LENGTH 9MP7-MPCBL-5-SS TUBING PSI CONNECTION ORIFICE LENGTH TH'K 1/4" O.D. 4MP7-MPCBL-5-SS 15,000 4MP /4" O.D. 4MF-MPCBL-5-SS 20,000 4MF /8" O.D. 6MP7-MPCBL-5-SS 15,000 6MP /8" O.D. 6MF-MPCBL-5-SS 20,000 6MF /2" O.D. 8MP7-MPCBL-5-SS 12,500 8MP /16" O.D. 9MP7-MPCBL-5-SS 12,500 9MP /16" O.D. 9MF-MPCBL-5-SS 20,000 9MF /4" O.D. 12MF-MPCBL-5-SS 20,000 12MF " O.D. 16MF-MPCBL-5-SS 20,000 16MF Materials of Construction Item # Description Material 1 Cap 316SS 2 Body 316SS 3 3/8 Ball 316SS 4 Gasket 316SS 5 Ball Support 316SS 6 Spring 316SS 27 Parker Hannifin Corporation Jacksonville, Alabama

28 FittingsMedium Pressure Valves Check Valves LENGTH 9MP7-MPCL-5-V-SS TUBING PSI CONNECTION ORIFICE LENGTH TH'K 1/4" O.D. 4MP7-MPCL-5-V-SS 15,000 4MP /4" O.D. 4MF-MPCL-5-V-SS 20,000 4MF /8" O.D. 6MP7-MPCL-5-V-SS 15,000 6MP /8" O.D. 6MF-MPCL-5-V-SS 20,000 6MF /2" O.D. 8MP7-MPCL-5-V-SS 12,500 8MP /16" O.D. 9MP7-MPCL-5-V-SS 12,500 9MP /16" O.D. 9MF-MPCL-5-V-SS 20,000 9MF /4" O.D. 12MF-MPCL-5-V-SS 20,000 12MF " O.D. 16MF-MPCL-5-V-SS 20,000 16MF Materials of Construction Item # Description Material 1 Cap 316SS 2 Body 316SS 3 O-ring Buna 4 Gasket 316SS 5 Poppet 316SS 6 Spring 316SS 28 Parker Hannifin Corporation Jacksonville, Alabama

29 Medium Pressure Fittings Valves Introduction Parker MPR series relief valves are offered in preset pressure relief ranges from 1500 to 20,999 psi. Relief valves are tagged with the proper factory preset pressures. Relief Valves (Factory Set) RATING CONNECTION ORIFICE MAX FLO CAPACITY (GPM) 8M8F-MPRA-****-SS 1,500 to 2,999 1/2" M X F NPT M8F-MPRA-****-SS 3,000 to 10,999 1/2" M X F NPT HF8F-MPRA-****-SS 11,000 to 20,999 9HF X 1/2" NPTF /2 NPT HF Materials of Construction Item # Qty Description Material 1 1 Cap 303SS 2 1 5/8-11 X 3 Soc Set Scr 304SS 3 1 Pressure Rating Tag 300 Ser. SS 4 1 Nut 303SS 5 2 Spring Seat 304SS 6 2 5/16 Ball 316SS 7 1 Spring Housing 304SS 8 1 O-Ring Viton 9 1 Stem 17-4PH-H Body 316SS 11 1 Removable Seat Gland 316SS Seal Ring 1500 to SS 13 1 Seal Ring 3000 to SS Seal Ring to SS 14 1 Danly Spring Steel 15 1 Stem Seat 17-4PH-H Parker Hannifin Corporation Jacksonville, Alabama

30 FittingsMedium Pressure Valves Union Couplings TUBING PSI CONNECTION ORIFICE LENGTH 1/4" O.D. 4MFU-SS 20,000 4MF /8 3/8" O.D. 6MFU-SS 20,000 6MF /4 9/16" O.D. 9MFU-SS 20,000 9MF /4" O.D. 12MFU-SS 20,000 12MF /8 1" O.D. 16MFU-SS 20,000 16MF /4 Bulkhead Union TUBING PSI CONNECTION ORIFICE LENGTH MOUNTING THREAD 1/4" O.D. 4MFBU-SS 20,000 4MF /4-16 3/8" O.D. 6MFBU-SS 20,000 6MF /8-14 9/16" O.D. 9MFBU-SS 20,000 9MF /8 1 1/ /4" O.D. 12MFBU-SS 20,000 12MF /8 1 5/8-12 1" O.D. 16MFBU-SS 20,000 16MF /8 1 7/8-12 Medium Pressure Elbows E G H F TUBING PSI CONNECTION E F G H TH K 1/4" O.D. 4MFL-SS 20,000 4MF /8" O.D. 6MFL-SS 20,000 6MF /16" O.D. 9MFL-SS 20,000 9MF /4" O.D. 12MFL-SS 20,000 12MF " O.D. 16MFL-SS 20,000 16MF Parker Hannifin Corporation Jacksonville, Alabama

31 Medium Pressure Fittings Valves Medium Pressure Tees E G H F TUBING PSI CONNECTION E F G H TH K 1/4" O.D. 4MFT-SS 20,000 4MF /8" O.D. 6MFT-SS 20,000 6MF /16" O.D. 9MFT-SS 20,000 9MF /4" O.D. 12MFT-SS 20,000 12MF " O.D. 16MFT-SS 20,000 16MF E Medium Pressure Crosses G H F TUBING PSI CONNECTION E F G H TH K 1/4" O.D. 4MFX-SS 20,000 4MF /8" O.D. 6MFX-SS 20,000 6MF /16" O.D. 9MFX-SS 20,000 9MF /4" O.D. 12MFX-SS 20,000 12MF " O.D. 16MFX-SS 20,000 16MF Connection Components Gland Plug TUBING TUBING 4MFG-SS 6MFG-SS 9MFG-SS 12MFG-SS 16MFG-SS 1/4" O.D. 3/8" O.D. 9/16" O.D. 3/4" O.D. 1" O.D. 4MFP-SS 6MFP-SS 9MFP-SS 12MFP-SS 16MFP-SS 1/4" O.D. 3/8" O.D. 9/16" O.D. 3/4" O.D. 1" O.D. Collar TUBING 4MFC-SS 1/4" O.D. 6MFC-SS 3/8" O.D. 9MFC-SS 9/16" O.D. 12MFC-SS 3/4" O.D. 16MFC-SS 1" O.D. 31 Parker Hannifin Corporation Jacksonville, Alabama

32 FittingsMedium Pressure Valves Caps TUBING PSI CONNECTION LENGTH 1/4" O.D. 4MFCP-SS 20,000 4MF /8 3/8" O.D. 6MFCP-SS 20,000 6MF /4 9/16" O.D. 9MFCP-SS 20,000 9MF /4" O.D. 12MFCP-SS 20,000 12MF /8 1" O.D. 16MFCP-SS 20,000 16MF /4 Medium Pressure Anti-Vibration Gland Assemblies TUBING PSI CONNECTION A B C 1/4" O.D. 4MFAVGA-SS 20,000 4MF /8" O.D. 6MFAVGA-SS 20,000 6MF /16" O.D. 9MFAVGA-SS 20,000 9MF /4" O.D. 12MFAVGA-SS 20,000 12MF " O.D. 16MFAVGA-SS 20,000 16MF "C" "B" Materials of Construction Item # Qty Description Material Collet Gland 316SS 2 1 Slotted Collet 316SS 3 1 Collet Body 316SS 4 1 Collar 316SS Anti-Vibration Component Part Numbers TUBING SLOTTED COLLET COLLET GLAND COLLET BODY COLLAR 1/4" O.D. 4MFAVSC-SS 4MFAVCG-SS 4MFAVCB-SS 4MFAVC-SS 3/8" O.D. 6MFAVSC-SS 6MFAVCG-SS 6MFAVCB-SS 6MFAVC-SS 9/16" O.D. 9MFAVSC-SS 9MFAVCG-SS 9MFAVCB-SS 9MFAVC-SS 3/4" O.D. 12MFAVSC-SS 12MFAVCG-SS 12MFAVCB-SS 12MFAVC-SS 1" O.D. 16MFAVSC-SS 16MFAVCG-SS 16MFAVCB-SS 16MFAVC-SS 32 Parker Hannifin Corporation Jacksonville, Alabama