MATERIAL SAFETY DATA SHEET *MSDS-ID-PRF680I* MIL-PRF-680 Type I Degreasing Solvent

Transcription

1 MATERIAL SAFETY DATA SHEET *MSDS-ID-PRF680I* 1. PRODUCT AND COMPANY INFORMATION PRODUCT NAME: MIL-PRF-680 Type I Inventory ID: PRF680I COMPANY INFORMATION 24 HR. EMERGENCY TELEPHONE NUMBER MACH-DYNAMICS (US Transportation): +1 (570) , ext Main Street (International Transportation): +001 (570) , ext.4 Susquehanna, PA Phone: (570) Fax: (570) Contact: Mark Gingerella 2. HAZARDS IDENTIFICATION OSHA STATUS: This product is hazardous (Combustible) as defined in the OSHA Hazard Communication Standard 29 CFR SYMPTOMS/EFFECTS OF OVEREXPOSURE Inhalation: Overexposure to high vapor/aerosol concentrations (at elevated temperatures) are irritating to the respiratory tract and may cause headaches, dizziness, anesthesia, drowsiness, unconsciousness, and could be fatal. Ingestion: Ingestion may cause irritation of the mouth, throat, and gastrointestinal tract with nonspecific discomfort such as nausea, headache, diarrhea, thirst, and weakness. Ingested product may be aspirated into the lungs and cause mild to severe pulmonary injury and could be fatal. Skin: Low order of toxicity. Frequent or prolonged contact may cause dermatitis. Contact may aggravate existing dermal conditions. Eyes: Slightly irritating but does not injure eye tissue. Vapors from heated materials are irritating to the eyes. Listed Carcinogens: None. 3. COMPOSITION/CHEMICAL INFORMATION DATE ISSUED : 5/1/2014 MSDS REF. No : PRF680I Chemical Name CAS Number Weight % Synthetic Isoparaffinic Hydrocarbon Page 1 of 6

2 4. FIRST AID MEASURES EYES: Immediately flush eyes with plenty of water for at least 15 minutes while holding eyelids open. Seek medical aid if irritation persists. SKIN: Flush skin with soap and water while removing contaminated clothing. If irritation occurs, seek immediate medical attention. Do not reuse clothing or shoes until thoroughly cleaned. INGESTION: Do not induce vomiting, and seek immediate medical attention. Do not attempt to give any liquids if victim is unconscious. Immediately give 2 glasses of water to a conscious person. INHALATION: Immediately remove victim to fresh air. If victim is not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Seek immediate medical attention. NOTES TO PHYSICIAN: None 5. FIRE FIGHTING MEASURES FLASH POINT AND METHOD: 53 C (127 F), ASTM D56 FLAMMABLE LIMITS: LEL 0.7, UEL 77 F (25 C) AUTOIGNITION TEMPERATURE: 689 F (365 C) General Hazard Combustible liquid; can form combustible vapors at temperatures at or above flashpoint. Extinguishing Media Dry chemical, chemical foam, carbon dioxide. Class BC, ABC fire extinguisher. Special Fire Fighting Procedures Self-contained positive pressure breathing apparatus and protective clothing should be worn in fighting fires involving chemicals. Unusual Fire and Explosions Hazards None known. 6. ACCIDENTAL RELEASE MEASURES GENERAL PROCEDURES: Ventilate area of leak or spill for at least 24 hours or until it has been declared safe. Remove all sources of ignition. Stop the leak if there is no risk involved. Clean-up personnel require protective clothing and respiratory protection from vapors. Absorb liquid with inert material. Only specially trained or qualified personnel should handle the emergency. Eliminate sources of ignition. Do not allow to enter drains or waterways. For small spills: Absorb with inert material and dispose of absorbents. Observe government regulations. Page 2 of 6

3 For large spills, dike affected area and excavate spilled materials and affected media. Observe government regulations. 7. HANDLING AND STORAGE GENERAL PROCEDURES: Keep away from heat, sparks, and flame. Surfaces that are hot may ignite liquid even in the absence of sparks or flame. Extinguish pilot lights, cigarettes, and turn off all other sources of ignition prior to use, and until all vapors are gone. Keep containers tightly closed and upright to prevent leakage. Use proper bonding and/or grounding procedures when transferring materials. Store in original container, preferably in a cool, ventilated, fire-resistant building. Avoid overheating or freezing. Since empty containers may retain product residues (vapor, liquid, or solid) all label precautions must be observed. COMMENTS: KEEP OUT OF REACH OF CHILDREN! Empty containers retain product residue and can be dangerous. Do not pressurize, cut weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks static electricity, or other sources of ignition. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION EXPOSURE GUIDELINES : OSHA HAZARDOUS COMPONENTS (29 CFR ) EXPOSURE LIMITS CHEMICAL NAME OSHA PEL ACGIH TLV ppm mg/m 3 ppm mg/m 3 Synthetic Isoparaffinic TWA None None None None Hydrocarbon STEL None None None None *MANUFACTURER recommended TWA of 1200 mg/m 3 (171 ppm) based on total hydrocarbons. ENGINEERING CONTROLS: Provide exhaust ventilation sufficient to keep the airborne concentration of this product below its exposure limits. Exhaust air may need to be cleaned by scrubbers or filters to reduce environmental contamination. PERSONAL PROTECTIVE EQUIPMENT EYES AND FACE: Use chemical safety goggles and/or full face shield where splashing is possible. Contact lenses should not be worn when working with this material. Maintain eye wash fountain and quick-drench facilities in work areas. SKIN: Wear resistant gloves (consult your safety equipment supplier). To prevent repeated or prolonged skin contact, wear impervious clothing and boots. RESPIRATORY: If exposure may or does exceed occupational exposure limits (Section 8) use a NIOSH approved respirator to prevent overexposure. In accord with 29 CFR , use either an atmosphere-supplying respirator or an air-purifying respirator for organic vapors. HYGIENIC WORK PRACTICES: Use good personal hygiene when handling this product. Wash hands after use, before eating, drinking, smoking, or using the toilet. Page 3 of 6

4 OTHER USE PRECAUTIONS: Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower. COMMENTS: May be harmful or fatal if swallowed. May irritate body tissues. Use with adequate ventilation. Avoid breathing vapor. Do not get in eyes, on skin, on clothing. Wash thoroughly after handling. 9. PHYSICAL AND CHEMICAL PROPERTIES Physical State: Liquid Appearance: Clear Liquid Odor: Mild hydrocarbon odor. ph: Not Applicable Flammable Limits: LEL 0.7, UEL 77 F (25 C). Flash Point: 53 C (127 F), ASTM D56 Autoignition Temp.: 689 F (365 C) Boiling Point (760 mm Hg): F ( C) Vapor Pressure (25 C): 0.8 mm Hg, C Vapor Density (Air=1): 6.2 Freezing Point: No data available Solubility in water: < 77 F (25 C) Evaporation Rate (n-bu=1): 0.1 Specific Gravity (15.5 C): 60 F (15.5 C) % Volatile by wt.: No data 10. STABILITY AND REACTIVITY STABLE: Yes. This product is stable under recommended storage conditions. HAZARDOUS POLYMERIZATION: Will not occur CONDITIONS TO AVOID: Avoid heat, sparks, and flame. Prevent vapor accumulation. INCOMPATIBILITY: Strong oxidizing agents. HAZARDOUS DECOMPOSITION PRODUCTS: None, other than normal products of combustion. Polymerization: Will not occur. 11. TOXICOLOGICAL INFORMATION No information available for this product. Refer to section 3 for information on health effects and section 8 for exposure limits. 12. ECOLOGICAL INFORMATION No information available for this product. Page 4 of 6

5 13. DISPOSAL INFORMATION DISPOSAL METHOD: The preferred options for disposal are to send to licensed reclaimers, or to permitted incinerators. Any disposal practice must be in compliance with federal, state, and local regulations. Do not dump into sewers, ground, or any body of water. EMPTY CONTAINER: KEEP OUT OF REACH OF CHILDREN! Empty containers retain product residue and can be dangerous. Do not pressurize, cut weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks static electricity, or other sources of ignition. RCRA/EPA WASTE INFORMATION: Chemical waste generators must determine whether a discarded chemical is classified as a hazardous waste. US EPA guidelines for the classification determination are listed in 40 CFR. Additionally, waste generators must consult state and local hazardous waste regulations to ensure complete and accurate classification. 14. TRANSPORT INFORMATION DOT: Not regulated for containers less than 119 gallon capacity (non-bulk). Combustible liquid PG-III Bulk containers ( 119 gallon capacity): UN1268, PETROLEUM DISTILLATES, N.O.S. (Isoparaffinic Hydrocarbons) Class 3, Packing Group III. IATA, IMDG, TDG: UN1268 PETROLEUM DISTILLATES, N.O.S. (Isoparaffinic Hydrocarbons) Class 3, Packing Group III. Flash Point: 53 C (127 F), ASTM D56 Autoignition Temp.: 689 F (365 C) *** MACH-DYNAMICS verifies that the material was supplied and shipped in the proper packages in accordance with DOT and federal regulations that are applicable to the mode of transportation selected. The shipper must verify that the packaging supplied is acceptable to be re-shipped in per the federal regulations applicable to the mode of transportation for reshipment. Regulations may change depending on mode of transportation selected.*** 15. REGULATORY INFORMATION TSCA: All components of this product are listed on the TSCA inventory. SARA Title III: Under the provisions of SARA Title III, sections 311/312 this product is classified into the Following Hazard Categories: Fire This information may be subject to the provisions of the community right-to- know Reporting Requirements (40 CFR 370) if threshold quantity criteria are met. SARA 313 None of the components appear on any of the EPA's lists of toxic or hazardous substances, or on the toxic chemicals list (40 CFR ). California Prop 65: None of the components of this product is listed in California's Safe Drinking Water and Toxic Enforcement Act of Proposition as a chemical known to cause cancer, birth defects, or other reproductive harm. CANADIAN DSL: IECSC (China): Listed Listed Page 5 of 6

6 16. OTHER INFORMATION APPROVED BY: Mark Gingerella TITLE: President / QC Manager NFPA CODES HMIS RATING Health : 1 Flammability : 2 Reactivity : 0 Personal Protection : G DISCLAIMER: To the best of MACH-DYNAMICS knowledge, all information, recommendations, and suggestions appearing herein concerning this product are taken from sources or based upon data believed to be reliable. Although reasonable care has been taken in the preparation of this information, MACH-DYNAMICS extends no warranties or guarantees, express or implied, makes no representations and assumes no responsibility as to the accuracy, reliability or completeness of the information presented. MACH-DYNAMICS assumes no liability arising out of the use of the product by others. The conditions or methods of handling, storage, use and disposal of the product are beyond MACH-DYNAMICS control. The information provided herein may not be valid for this product if it is used in combination with any other materials or process. It is the user s responsibility to determine the suitability of the product, review the information provided herein, assess the safety and toxicity of the product and to comply with all applicable laws and regulations. For this and other reasons, MACH-DYNAMICS does not assume responsibility and expressly disclaims liability for any loss damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. Page of 6